System Wiring Overview

AC740502B AC740500B AA740502C (REF. OPTION CODES 9636C, D & F)

2 STEPPER MOTORS (1 PER BANK) VHP SERIES FOUR 12 CYLINDER WIRING DIAGRAM
STEPPER STEPPER STEPPER LEFT BANK RIGHT BANK
(GAS REG) (GAS REG) (GAS REG) E STOP SWITCH E STOP SWITCH

PRIMARY IGNITION HARNESS

FLYWHEEL
HOUSING
FRONT LEFT BANK INTAKE MANIFOLD (TOP VIEW) INTAKE MANIFOLD PRESSURE SENSOR - LEFT BANK
SECTION 211893, A740119, 740119 & 740043A
CRANK ALTERNATOR 1 2 1 2 1 2 1 2
(SIDE VIEW) JUNCTION
SENSOR BOX
A295844D
295844D
740043C IPM-D 3 4 3 4 3 4 3 4
OXYGEN SENSOR INTAKE MANIFOLD TEMPERATURE SENSOR
HARNESS ALTERNATOR
A740120, 740120 & 740043B CABLE
ENG GND + JUMPER B
JUMPER A
JUMPER B

JUMPER A

G LEAD 2 GND
FUELV RLY

ESTOP SW
ESTOP SW

ESTOP SW
ESTOP SW

G LEAD 2 GND

G LEAD
IPM F/B

IPMF/BRET
FUELV SW

G LEAD
OXYGEN KNOCK SENSOR -
SENSOR 2 PIN CONNECTOR
CYL 6L CYL 5L CYL 4L CYL 3L CYL 2L CYL 1L IGNITION COIL ALTERNATOR "G" LEAD
ESM E STOP SWITCH HARNESS
ENG GND
ENG GND ALTERNATOR

HARNESS
(REF. OPTION CODE 3433E)

ECU INPUT B

LB
MONITOR
HARNESS

ALTERNATOR
LEFT TOP WATER
BANK MANIFOLD CAM SENSOR 14 PIN CONNECTOR
(TOP VIEW) A295844D (12 OPEN SPACES)
295844D IPM-D POWER
EXHAUST 740043C 2 PIN CONNECTOR
OUTLET GEAR COVER (1 OPEN SPACE)
COOLANT
TEMPERATURE (TOP VIEW) ALTERNATOR MONITOR 14 PIN CONNECTOR
RIGHT SENSOR (5 OPEN SPACES)
BANK A740120 ECU CONNECTION
CAN HARNESS
740120

RB
740043B ECU CONTROL HARNESS
ENG GND ENG GND
CYL 6R CYL 5R CYL 4R CYL 3R CYL 2R CYL 1R

HARNESS
ECU INPUT A
ESM E STOP SWITCH HARNESS

ENG GND RS 232

CONNECTION
CRANKCASE

ESM HARNESS WITH ACTUATORS

WIRED IF ELECTRIC START AND ALTERNATOR OPTION SPECIFIED
WIRED IF ELECTRIC START AND ALTERNATOR OPTION SPECIFIED
EXHAUST TEMP OIL TEMPERATURE OIL HEADER RAIL ECU
ESM ACTUATOR HARNESS

SENSOR SENSOR (SIDE VIEW)

78212C
A740120 OIL PRESSURE
EXH TEMP. SENSOR SENSOR 78212C, A740118
HARNESS 740120
740043B 740118 & 740043
ECU CONTROL HARNESS

INTAKE MANIFOLD PRESSURE

RIGHT BANK SENSOR - RIGHT BANK
INTAKE MANIFOLD 211893, A740119 ENG GND
(TOP VIEW) 740119 & 740043A ECU INPUT "A" HARNESS
POWER
ECU INPUT "B" HARNESS +24V POWER DISTRIBUTION
ACTUATOR BOX
AC740502B AC740500B AA740502C
(SIDE VIEW)
STEPPER STEPPER STEPPER ESM ACTUATOR HARNESS W/GAS REGULATOR ACTUATORS
ACT/IPM/STEP
(GAS REG) (GAS REG) (GAS REG)

E STOP SWITCH
(REF. OPTION CODES 9636C, D & F)
2 STEPPER MOTORS (1 PER BANK)
ECU/IPM DATA/TEST
JUMPER HARNESS
CUSTOMER INTERFACE
WIRED IF ELECTRIC START OPTION SPECIFIED ONLY
AIR PRELUBE

PMR
AC/DC ESM START HARNESS (AIR AND ELECTRIC)
PMR START/LEAN
RELAY GROUND
See Note #6

SM2
SM1
in lower ENGINE OPTIONS

PMR
GROUND

PMR
AC PRELUBE OPTION right corner SMC2 SMC1
(REF. OPTION CODES 5229A,B)
FUEL GND
ASV GND

FUEL V
ASV

REMOVE SEE TABLE 2.10-4

EXPOSED END REMOVE LOCAL CONTROL OPTIONS
OF GREEN WIRE EXPOSED END CUSTOMER
COIL IN OF GREEN WIRE CONNECTION
CONDUIT BOX *FUEL VALVE AIR START VALVE COIL IN
CONDUIT BOX BATTERY GROUND
SM2 SM1
POWER DISTRIBUTION

PMR
See Note #6 in BOX BRACKET See Note #6 in ENGINE GROUND
lower right corner lower right corner
SEE TABLE 2.10-3
CUSTOMER

PMR GROUND
1/2"
CONNECTION GROUND STUD

PRELUBE MOTOR RELAY - - - -

3.5-3.9 AMP. A1 A2 + + + +
(REF. OPTION CODE 5230) RIGHT BANK NOTES
OIL PAN ACCESS
*BATTERY 24VDC *BATTERY 24VDC DOOR #4 1. Electrical devices are shown in normal engine operating mode. 5. Wiring per Table 2.10-1 on page 2.10-2
PRELUBE PUMP ELECTRIC START
MOTOR - 35 AMP (REF. OPTION CODE 9000) (on/off switch terminals 1&2 normally closed, 3&4 normally open). 6. Component not supplied by Waukesha.
24 VDC 2. #10 AWG wire Suppression diode must be installed.
3. #2/0 AWG wire 7. Optional equipment.
4. #6 AWG wire

Figure 2.10-3 VHP Series Four 12 Cylinder Wiring Diagram

FORM 6295 Fourth Edition 2.10-11

12