Mechanical

Cladding
Fixation
catalogue

www.ikkgroup.com
INDEX
- About SFSP 4
- General Information 20
- Types of Load 26
- Types of Fixings 34
Mechanical - L-Brackets
- Z-Brackets
47
59

Cladding - Case Study

- Omega Bracket
- Fishtail Bracket
64
72

Fixation - Corrugated Dowel

- Examples of Steel Back
75
78
82
Support System
- C-CHannels Loads & Supports 90
- Anchors 94
- Locations 102

1
www.sfsp-ikk.com
ABOUT
SFSP

3
 Specialized Factory for Steel Products Co. Ltd
Sigma Factory for Steel Products
www.sfsp-ikk.com

Specialized/Sigma Factory for Steel Products (SFSP) was first established in KSA in 1989 and has been expanding
ever since through a variety of products and through its geographical presence.
Production at the factory is observed using modern practices of manufacturing methods in the steel construction
industry with a definite compliance to international standards of fabrication.

SFSP has manufacturing facilities in KSA, UAE, Egypt, and Lebanon. SFSP adapts quickly and easily to market
demands and requirements. The factory is operating a top of the line production machinery, fully automated with
highest technology to ensure quality and maintain speed with delicacy.

Quality at SFSP is uncompromised; the factories have been able to acquire ISO 9001: 2015 Quality Management
System, ISO 14001:2015 Environmental Management certified factory, and OHSAS 18001:2007 Occupational
Health and Safety Management factory.

HOT-DIP GALVANIZATION
SFSP has an in-house state of the art Hot-Dip Galvanization facility, which permits a full control of the quality of its
finished products, offering better services to our clients globally.

4
 Specialized Factory for Steel Products Co. Ltd
www.sfsp-ikk.com

Specialized Factory for Steel Products Co., ltd,

which is part of Isam Khairi Kabbani Group
of companies is a leading fabricator of steel
construction products serving the kingdom of
Saudi Arabia since 1989.

The factory operates under TQM ISO modules,

using the latest modern technology in the
steel fabrication and manufacturing industry
in conformity with International standards for
safety and in compliance with the environmental
regulations in the Kingdom.

The factory has inaugurated its new manufacturing

facilities which is located in the 3rd Industrial Area
of Jeddah with a total built facilities of 37,000
squared meters.

The facilities include two manufacturing areas, a hot dip galvanization advanced section, warehousing areas
and administrative building. The project is an advanced environmental low emissions factory built with a definite
consideration of the safety of its workers and visitors.

5
 Specialized Factory for Steel Products Co. Ltd
Sigma Factory for Steel Products
www.sfsp-ikk.com

TECHNICAL SERVICES
A crucial factor in the job of a factory is to provide continuous technical services and consultations.
That’s why SFSP has invested in a professional team of researchers and specialists.

SFSP has recruited brilliant graduates and experienced engineers having the appropriate knowhow on the on latest
technology changes and development in the steel building materials industry.

The product range is developed and updated according to the relevant standards of fabrication across markets,
whilst the business processes are evaluated to achieve maximum efficiency.

SFSP R&D Core Objectives

- Carry out responsibilities effectively in a safe and healthy work environment.
- Develop and implement research programs relevant to the products and solutions introduced and ensure that the
results are communicated clearly in-house and among the clients , concisely and accurately.

DESIGN AND ENGINEERING OFFICE - GERMANY

Unitech Deutshland GmbH is

the design office of Unitech
for Building and Construction
Materials and is situated in
Stuttgart, Germany.

6
SOCIAL RESPONSIBILITY
Being socially responsible is a part of who we are and
how we do our business. We aim to provide useful
products and services, to provide jobs and development
opportunities for our communities, and to gain
satisfaction through meaningful work.
We make a difference by acting on the values and
principles of our societies and we inspire others to do
so. At SFSP, we anticipate and reduce threats caused
by environmental changes or natural disasters, and we
are well adapted to significant social changes.
We contribute to a more sustainable society by means
of value and support to our consumers, supply chains,
and stakeholders. We are keen to identify ways they
can improve our impacts on the people and places we
work and live in, and thereby become more valuable
and valued members of society.

- Organizational governance: We promote accountability

and transparency at all levels, thus, promoting - Fair operating practices: Practicing accountability and
responsibility fairness in dealings with other businesses
- Human care: We treat individuals with respect; and
make efforts to help members of vulnerable groups At SFSP, we are committed to continuous improvement
- Labor practices: We provide just, safe and favorable – ongoing learning, process review and innovative
conditions to workers thinking that foster new initiatives; and better practices.
- Environment: At SFSP, we Identify and improve Our environmental programs evolve to meet today’s
environmental impacts of our operations, including the changing needs while; protecting resources for future;
resource use of natural resources and waste disposal. generations.

HEALTH AND SAFETY

The Factory Management regard the health and safety 2. Ensures that all facilities and equipment are safe and
of the employees, clients and all others that may be properly maintained.
affected by their operations to be of a major importance. 3. 
Provides products that can be applied and used
safely and without risk to health.
In support of this, the management promotes health 4. Provides and maintain working procedures, that are
and safety throughout the Factory’s operations safe and without risk to health, throughout the its
and endeavour to engender a positive attitude in all operations in respect of:
employees towards the prevention of accidents and •T he use, handling, storage, transports and disposal
maintenance of healthy working arrangements. of materials and substances.
• The use of factory equipment.
The Factory satisfies the requirements of the Health, •P otential emergency situations, including first aid,
Safety and related legislation by setting out the fire and escape of substances.
responsibilities of all levels of staff and the arrangements 5. Ensure the competence of employees.
for carrying out those responsibilities and in particular
do what is reasonably practicable to: The factory is an OHSAS 18001:2007 Occupational,
1. Maintains safe & healthy working conditions. Health and Safety Management certified Factory.

7
ENVIRONMENTAL AWARENESS
SFSP is committed to the following:
•C  ompliance with all statutory and regulatory
requirements related to its activities, products and
services and the environmental aspects.
• Identifying quality and environmental objectives by
review and audit of the processes both in-house and
on-site.
•F  ormally setting objectives based on the results of
the process reviews and their significance in relation
to their impact on the environment and the continual
improvement of the quality and environmental
management system.
• Implementing management programs to achieve
these objectives.
• Investing in a well-trained and motivated workforce.
•W  orking closely with suppliers and customers to
ensure mutual understanding and benefits of the
environmental aspects consideration.
•R  eviewing our policy and objectives as part of the
Management Review Process.
•C  ommunicating this policy to all persons working for SFSP operates under environmental management
or on behalf of the organization. system certification BS EN ISO 14001:2004 and
•P  reventing and minimizing Pollution to the environment. maintain it through registration and annual review.

SFSP facilities are equipped with the most technologically advanced machinery amongst are Laser
Cut Machines, Robot Bending Sets, Welding Robot Sets, sophisticated Cable Management Production
Lines, as well as Specialized Industrial Sections for its Hot Dip Galvanization facilities.

8
CNC MACHINES

WELDING
ROBOT
SETS

CNC FIBER LASER

PUNCHING CUT

ROBOTIC
BENDING
CELL

9
 SFSP CERTIFICATION

ISO 45001 : 2018 ISO 9001 : 2015

(Occupational Health & Safety) (Quality Management Systems)

14001 : 2015
(Environmental Management System)

10
 STD 096 ISO 14001 : 2015
(Q-Mark Certificate) (Environmental Management System)

OHSAS 18001 : 2018 ISO 9001 : 2015

(Health & Safety Management System) (Quality Management System)

11
 SFSP CERTIFICATION

BS EN 61537:2007 (KEMA - KEUR Certified For BS EN 61537:2007 (KEMA - KEUR BS Certified

Cable Management Products) For Cable Management Products)

CERTIFICATE CERTIFICATE
Issued to: Issued to:
Applicant: Manufacturer/Licensee: Applicant: Manufacturer/Licensee:
Isam Kabbani Trading Est. (Unitech) Sigma Factory for Steel Products (SFSP) Isam Kabbani Trading Est. (Unitech) Sigma Factory for Steel Products (SFSP)
Rashidiya Saih Shuaib 3, 4R/A, Dubai Industrial City, Rashidiya Saih Shuaib 3, 4R/A, Dubai Industrial City,
Dubai, United Arab Emirates Dubai, United Arab Emirates Dubai, United Arab Emirates Dubai, United Arab Emirates

Product : Cable management system Product : Cable management system

Trade name : SFSP Trade name : SFSP
Types : IE-CT-X-10, IE-CT-X-12, IE-CT-X-15, IE-CT-X-20 Types : IE-CT-X-10, IE-CT-X-12, IE-CT-X-15, IE-CT-X-20

The product and any acceptable variation thereto is specified in the Annex to this certificate and the The product and any acceptable variation thereto is specified in the Annex to this certificate and the
documents therein referred to. documents therein referred to.

DEKRA hereby declares that the above-mentioned product has been certified on the basis of: DEKRA hereby declares that the above-mentioned product has been certified on the basis of:
 a type test according to the standard IEC 61537:2006 and EN 61537:2007  a type test according to the standard BS EN 61537:2007 based on IEC 61537:2006
 an inspection of the production location according to CENELEC Operational Document CIG 021  an inspection of the production location according to CENELEC Operational Document CIG 021
 a certification agreement with the number 2156954  a certification agreement with the number 2156954

DEKRA hereby grants the right to use the KEMA-KEUR certification mark. DEKRA hereby grants the right to use the KEMA-KEUR BS certification mark.

The KEMA-KEUR certification mark may be applied to the product as specified in this certificate for the The KEMA-KEUR BS certification mark may be applied to the product as specified in this certificate for the
duration of the KEMA-KEUR certification agreement and under the conditions of the KEMA-KEUR duration of the KEMA-KEUR BS certification agreement and under the conditions of the KEMA-KEUR BS
certification agreement. certification agreement.

This certificate is issued on: 20 January, 2014 and expires upon withdrawal of one of the above mentioned This certificate is issued on: 3 February, 2014 and expires upon withdrawal of one of the above mentioned
standards. standards.

Certificate number: 2156954.01 Certificate number: 2156954.02

DEKRA Certification B.V.

DEKRA Certification B.V.

2 < 2 <
drs. G.J. Zoetbrood H.R.M. Barends
drs. G.J. Zoetbrood H.R.M. Barends Managing Director Certification Manager
Managing Director Certification Manager
© Integral publication of this certificate is allowed
© Integral publication of this certificate is allowed
ACCREDITED BY THE
ACCREDITED BY THE DUTCH ACCREDITATION
DUTCH ACCREDITATION COUNCIL
COUNCIL

DEKRA Certification B.V. Meander 1051, 6825 MJ Arnhem P.O. Box 5185, 6802 ED Arnhem The Netherlands DEKRA Certification B.V. Meander 1051, 6825 MJ Arnhem P.O. Box 5185, 6802 ED Arnhem The Netherlands
T +31 88 96 83000 F +31 88 96 83100 www.dekra-certification.com Registered Arnhem 09085396 T +31 88 96 83000 F +31 88 96 83100 www.dekra-certification.com Registered Arnhem 09085396

UL Certification* UL Certification*
(Cable Trays) (Chute Type Fire Doors)

CERTIFICATE OF COMPLIANCE
Certificate Number 20170811-R38825
Report Reference R38825-20170811
Issue Date 2017-AUGUST-11

Issued to: Sigma Factory for Steel Products

Saih Shuaib 3, 4 R/A Dubai Industrial City
Opposite DEWA Substation
Dubai UNITED ARAB EMIRATES

This is to certify that CHUTE-TYPE FIRE DOORS

representative samples of Chute-type fire door and frame assembly of the insulated
type, rated up to and including 2 hr, 450°F Temperature
Rise Rating.

Have been investigated by UL in accordance with the

Standard(s) indicated on this Certificate.

Standard(s) for Safety: ANSI/UL 10B, Fire Tests of Door Assemblies

Additional Information: See the UL Online Certifications Directory at
www.ul.com/database for additional information

Only those products bearing the UL Certification Mark should be considered as being covered by UL's
Certification and Follow-Up Service.

Look for the UL Certification Mark on the product.

Bruce Mahrenholz, Director North American Certification Program

UL LLC

Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please
contact a local UL Customer Service Representative at http://ul.com/aboutul/locations/

Page 1 of 1

12
 Specialized Factory for Steel Products Co. Ltd
Sigma Factory for Steel Products
www.sfsp-ikk.com

SFSP PRODUCTS
SFSP produces a variety of products ranging from cable management systems; cable trays, cable ladders, basket
trays, trunkings and support systems, to mechanical cladding fixations, steel lintels and block work accessories,
plasterers’ beads, expanded metal and block work reinforcement, strut channel systems, pipe clamps & hangers,
gypsum profiles as well as garbage and linen chutes. With the introduction of new machines and the enhancement
of production methods, SFSP continues to develop its production methods systematically as well as thoroughly.
Its design office in Stuttgart, Germany provides a comprehensive design and calculation case studies, enabling the
factory to have the safety factors required for the usage of its products.

CABLE TRAYS & ACCESSORIES

Cable Trays are designed to meet most requirements of cable and
electrical wire installations and comply to local and international
standards of fabrications and finishes.

CABLE LADDERS (WELDED & SWAGED)

Cable Ladders of different side heights are available upon request.

BASKET TRAYS & ACCESSORIES

SFSP’s Basket Tray systems make connections fast and simple with
limited need for tools. Its design allows for continuous airflow, and
prevents heating up of cables. SFSP’s Basket Tray comes in a full
range of sizes and is made with high-strength welded steel wires.

CABLE TRUNKINGS
Cable Trunkings and Accessories are offered in a comprehensive
range. Mill galvanized, hot-dip galvanized, and powder coated are the
various finishes produced in our factories.

UNDERFLOOR TRUNKING
Underfloor Trunking Systems solutions incorporate a range of products
for the distribution of power and data services , it is a coordinated set of
containments that protect, segregate, contain, and route cables within
a given environment.

13
 CABLE MANAGEMENT SUPPORT SYSTEMS
Cable Support Systems are well designed to provide necessary support for cable
trays, cable ladders and trunkings. Cable supports are manufactured according to
common standards from high quality raw materials.

C-CHANNEL STRUT SYSTEMS

SFSP’s Metal Framing Systems provide an economical solution for electrical,
mechanical and industrial supports with a wide variety of applications in the
construction industry.
Applications: - Pipe and Conduit Supports - Tunnel Pipe Stanchions - Racks and
Shelvings - Wall Framings.

EXPANDED METALS, PLASTERERS` BEADS

Expanded Metals help the formation of joints, protection of corners and resistance
against cracks, chips and impact damage.

BLOCK LADDER REINFORCEMENT

SFSP ladder and truss types are used for the reinforcement of brick and block
masonry to give improved tensile strength to walls subjected to lateral loading e.g.
wind and seismic. SFSPblock reinforcements reduces the risk of cracking either at
stress concentration around opening.

STEEL LINTELS & BLOCK WORK ACCESSORIES

Steel Lintels provide a combination of strength and light weight, resulting in efficient
load bearing performance and increased productivity on site. They are characterized
by their ease of installation in addition to time as well as money saving.

PIPE CLAMPS & HANGERS

Pipe Clamps and Hangers from SFSP used in the support of pipes and equipments
are manufactured according to the highest standards of fabrication.A diversified
choice of Pipe Hangers, Pipe Clamps, EMT Straps, Omega Clamps, Beam Clamps,
J and U-Bolts and Threaded Accessories.

MARBLE & GRANITE FIXINGS

Stangle Cladding Fixation includes design, calculation and production of several
types of mechanical fixings and accessories used for cladding purposes. Stainless
and galvanized steel are among the various materials used in the fabrication.

DRY WALL & CEILING PROFILES

SFSP provides a complete product range for dry wall and ceiling constructions.
Studs, Runners, Furring Channels, Ceiling Channels and Wall Angles are among the
range of products produced to service the dry wall installers.

GARBAGE & LINEN CHUTES

Chutes from SFSP are very convenient, simple and low cost method of controlling
and disposing of refuse and linen. Chutes meet the most stringent requirements
of environmental health and safety. Chutes are used as original equipment in new
buildings, such as : Hotels, Hospitals, High Rises and Residential Towers.

14
 SFSP Products are solely distributed by UNITECH for Building and
Construction Materials

All Products Manufactured by SFSP are Solely Distributed by SFSP Sister Companies in the Following
Countries

KSA BAHRAIN UAE

Isam Kabbani & Partners for Building Isam Kabbani Trading Est. Issam Kabbani Trading Est. –
and Construction Materials Co., Ltd. ‫مؤسسة عصام قباين التجارية‬ ‫مؤسسة عصام قباين للتجارة‬
‫رشكة عصام قباين ورشكاه ملواد األنشاء والتعمري املحدودة‬

KUWAIT OMAN EGYPT

Hassan Kabbani for General Isam Kabbani & Partners UNITECH Egypt for Building
Contracting Est. Trading Co. Materials
‫مؤسسة حسان قباين للمقاوالت العامة للمباين‬ ‫رشكة عصام قباين ورشكاه للتجارة‬ ‫رشكة يونيتك مرص ملواد البناء‬

JORDAN LEBANON

Jordan Build Co. for Building & UNITECH ME s.a.r.l –

Construction Materials – ‫م‬.‫م‬.‫رشكة يونيتك ميدل إيست ش‬
‫رشكة بناء األردن ملواد اإلنشاء و التعمري و الكهرباء‬

SFSP CUSTUMER SERVICE CALL CENTER

KSA UAE
+966 13 8590097, Ext. 3214 +971 4 8181925, Ext. 4269

15
 IKK UNITECH
Group of Companies ISAM KABBANI & PARTNERS FOR
BUILDING & CONSTRUCTION MATERIALS
The IKK Group is a major business institution,
serving most of the Arab World in the Isam Kabbani & Partners for buildings & construction
industrial, construction and trading fields, materials co. Ltd (UNITECH) which is part of
as well as in specialized maintenance and the IKK group of companies is recognized and
services. acknowledged for the quality and reliability of its
products and services as well as for the commitment,
Today, the IKK Group of Companies is a professionalism and experience of its employees.
pioneer in waterproofing, weatherproofing,
building material supplies, UPVC and CPVC Isam Kabbani & partners for buildings & construction
and high density polyethylene pipes and materials co. Ltd (UNITECH) core valuse are to offer
fittings and several other products for the value products and services to its clients, to work
construction industry. closely with them in a lasting business partnership that
provides an outstanding performance.
The Group is also represented in the
sanitary products, steel production, kitchen A partnership based on trust, harmony, and a hard to
manufacturing, telecommunications, food, beat services and solutions.
decoration, re-insurance and real estate
business domain. Our Factories have acquired, in addition to ISO
9001: 2015 Quality Management System, the ISO
Composed of 60 companies, the IKK Group 14001:2015 Environmental Management System, and
operates through almost 200 divisions, OHSAS 18001:2007 Occupational Health and Safety
branches and outlets; it is spread over Management factory.
11 countries, covering all major cities in
the region and employing around 13,000 Our care for the environment has been translated via
employees. Isam Kabbani &partners for buildings &construction
materials co. Ltd (UNITECH)’s membership in the US
Our vision is to maintain and improve our Green Building Council as a Golden Member.
leading position as a contractor whose
reputation is built on the ability to completely Our Vision
UNITECH to be the Customer’s First Choice.
satisfy customers by providing high quality
services. As specialists in their respective
Our Mission
fields, our teams of professionals are We have the conviction to be the leader in building &
dedicated to a standard of excellence for construction industry through:
quality and performance, through continuous
development, which will set standards in our - Providing Excellence in Services with Passionate and
industry. Educated Sales Force
We are simply providing solutions for a future - Strengthen Culture through Unified Sense of Purpose
of success. - Innovative Product Range which is Customer Centric
- Reputable and Quality Service Company
Our mission is to provide our part of the Arab - Attracting, Engaging and Retaining Talent
World with local and reliable services in a
Our Values
variety of sectors and products.
Unitech’s core values are based on:
To create employment to thousands of • Excellence: Highest Quality.
personnel and in-house training for hundreds • Integrity: Outstanding Customer Service.
of young Arab graduates in crucial sectors to • Service with Pride: Highly Effective Business
the benefit of the IKK Group, the graduates Operation.
themselves and their own communities.

To set a good example of our basic business

philosophy: “Hire well, train well, pay well and
treat well.”
16 16
MARBLE & GRANITE FIXINGS
Stangle Cladding Fixation includes design, calculation and production of several types of mechanical fixings and
accessories used for cladding purposes. Stainless and galvanized steel are among the various materials used in
the fabrication.
Calculations are provided by our design office in Stuttgart, Germany.

INTERNATIONAL STANDARDS FOR CLADDING TYPES OF FIXINGS

DESIGN

Design & Calculation Standards Principles for the Fixing of Building Cladding
Reference is made to the following standards for the The fixing systems for building cladding are composed
design and structural calculations of Natural Stone of several elements (angles, expansion bolts, screws,
Fixing Systems. nuts, washers, etc), each of which shall present the
appropriate mechanical features in respect to the
American Standards: requirements posed by the specific project. Any type of
- Uniform Building Code 1997-Volume 2 cladding, once fixed, is subject to two primary types of
- ASTM A 276 Standard specification for stainless steel load:
bars and shapes. - Permanent load (the dead load), due to the weight of
- ASTM 666 Standard specification for annealed or the cladding itself;
cold-worked austenitic stainless steel sheets. - Variable load (applied loads), due to the wind, thermal
- ASTM C1354 / C1354M - 09 Standard Test Method expansions, seismic motions, etc.
for Strength of Individual Stone Anchorages in
Dimension Stone Two fundamental types of fixing systems result:
- Load-bearing fixing: to support the permanent load
British Standards: and the vertical components of the variable loads.
- BS 8298 Design and installation of natural stone - Restraining fixing: to support the horizontal
cladding. components of the loads. Restraining fixings instead,
- BS 1449 Part 2 Steel plates, sheets and strips serve to maintain the slabs in the positions specified
stainless and heat resisting. by the project design. Thanks to the systems of
- BS 6105 Corrosion resistant stainless steel fasteners. adjustment with which they are equipped, the
- BS 5950 Structural use of steel work in building. absence of perfect verticality in the external surfaces
- CP3, Chapter 5, Part 2 Wind loads. may be easily overcome.
- BS 970 Part 3 1991, Mechanical properties for
stainless steel. TYPES OF FACADE BUILDING SUBSTRUCTURE
1- Stone fixed to concrete wall
German Standards: 2- Stone fixed to hollow block wall
- DIN 1045 Concrete and reinforced concrete, design 3- Stone fixed to solid block
and dimensioning. 4- Stone fixed to composite substructure
- DIN 1053 Masonry, design and dimensioning.
- DIN 1055 Design loads for buildings. LOADS
- DIN 18 516 Cladding for external walls. - Self load = (Dead Load)
- DIN 18 800 Steel structures, design and - Wind load - Seismic load
dimensioning. - Temperature variation load
- DIN 18 801 Steel framed structures.

17 17
www.sfsp-ikk.com
 GENERAL
INFORMATION

19
 The most common types of stone are:

Granite Travertine Marble Slate Limestone

Natural stones have as much colors as you can imagine. The variety of color and texture of the natural
stone is huge.

The very common finishes are:

- Polished, Honed, Bush Hammered and Sandblasted for Marble.
- Polished, Honed, Flamed, and Sandblasted for Granite.

Types of Facade Building Sub-Structure

Stone fixed to concrete wall Stone fixed to hollow block wall

Stone fixed to solid block wall Stone fixed to composite substructure

20
 Choice of Fixation System In Relation to The Components of The Stone Facades.

When natural or reconstituted stone has been chosen as a cladding material it

is necessary to give consideration to the following key areas for the purposes of
choosing the most appropriate fixing system:
1) Type of structural material (e.g. concrete / block)
2) Design of cavity (e.g. ventilated / full fill insulation)
3) Design of stone joint (e.g. open /closed )
4) Size of stone (e.g. thickness /panel size)
5) Design duration of building

Required Thickness of Stone Cladding

Thickness of stone and depth of slot for corbel plate.
Stone location Stone type
Minimum thickness of stone Minimum depth of slot
Stone thickness , T
behind a cramp for a corbel plate, d

G T Mb Ls G T Mb Ls G T Mb Ls
Mw LS Ss Mw Ls Ss Mw Ls Ss
H H H
SL SL SL
Q Q Q
mm mm mm mm mm mm mm mm mm mm mm mm

Cladding (external)
Less than 3.7 m above ground or floor level
and continuously 20 20 20 50 7 7 72) 253) Not applicable
supported (incl. fascias)
Fascias less than 3.7 m above ground or floor
30 30 NA 50 12 12 NA 203) 20 20 NA 253)
level (incl. fascias)
More than 3.7m above ground or floor level
40 40 NA 75 15 15 NA 303) 25 25 NA 373)
(incl. fascias)
Soffits (including inclined soffits)4) 40 40 NA 75 15 15 NA 303) Not applicable

Sills, copings and supported reveals 30 30 NA 50 12 12 NA 203) Not applicable

stone faced concrete units 30 30 NA 50 Not applicable Not applicable

Lining (internal)

Less than 7 m above ground or floor level and

20 20 20 50 7 7 72) 203) Not applicable
continuously supported (incl. fascias)5)

Less than 7 m but more than 3.7m above

ground or floor level on corbels in slots (incl. 30 30 NA 50 12 12 NA 203) 20 20 NA 253)
fascias)
More than 7m above ground or floor level (incl.
30 40 NA 75 12 15 NA 303) 20 25 NA 373)
fascias)
Soffits (including inclined soffits)4) 40 40 NA 75 15 15 NA 303) Not applicable

1) Abbreviations
G: Granites - Ls: limestones (e.g. Portland, Bath, Clipsham)
LsH: Hard limestones (e.g. Roman stone) - Mb: Brecciated marbles - Mw: Homogeneous marbles
Q: Quartzites m- mSL: Slates (those unlikely to delaminate). - Ss: Sandstone (e.g. York, Northumberland, Scottish)
- T: Travertines
2) Breccated marbles may need to be reinforced with block liners but in assessing the minimum thiickness of
stone behind a cramp mortice the thickness of the block liner should be ignored.
3) Half thickness if stone is more than 75 mm thick.
4) The figures in the table apply to soffit stones not exceeding 900mm x 600mm. If stones of a greater size
are requiredconsideratin should be given to using some face fixings and/or additional fixings in the length
and/or increased thickness. Internal soffit stone not less than 1.2m and not more than 3.7m above floor level,
continuously supported at reveals may be 20mm thick for G, Q, SL, T, LsH, Mw, and 50mm for Ls and Ss.
5) Internal cladding between 3.7m and 7m in height in a continuous face should have an intermediate corbel
course.
Table based on BS 8298 stone thickness table

21
FIXINGS IN HORIZANTAL OR VERTICAL JOINTS
Fixation In The Horizontal Joint

The brackets carry half the weight of the natural stone slabs in horizontal installation. Brackets bear half the
weight of the slab above and also act as restraint, holding the slabs below and restraining them against wind
pressure and suction.

Load Bearing & Restraint Restraint

Direct fixing
to wall

Load Bearing & Restraint

Fixation In The Vertical Joint

The load bearing carry the full weight of the natural stone slab in vertical installation. Each bracket bears half the
weight of the slab on the right and half the weight of the slab on the left. Restraint brackets hold the slabs below
and restrain them against wind pressure and suction.

Restraint
Direct fixing
to wall

Load Bearing & Restraint

22
 Determining Anchor Loading Fv

Fsw : self weight of natural stone panel

a) Support anchor in vertical joint One
Installation At Horizontal Joints Fsw support anchor carries the dead load (Fv) of
Fv= one natural-stone panel
2

Example :
Fsw/2 Fsw/2
Natural-stone panel b/h/s
(width/ height/ thickness) = 0.6/1.00/0.04m
Density (Design weight) = 27 kN /m³
Anchor loading Fv = 0.6 * 1.00 * 0.04 * 27 =
0.65kN = 65 kg.

Self weight per panel: Fsw = Fv = 65kg

b) Support anchor in horizontal joint One

support anchor carries the dead load (Fv) of
Load Bearing &
Restraint half natural-stone panel.

Example:
Natural-stone panel b/h/s = 0.6/1.00/0.04/m
Density= 27 kN/m³
Anchor loading Fv = Fsw/2 = 0.32kN
Fv = 32kg

The shape and the material of the facing to

be anchored

Determining Anchor Loading FH (Wind loa-

ding):

Example:
Natural-stone panel = 0.6/1.00/0.04m
Wind load W = 1.1 kN/m² (Wind pressure) for
Installation at vertical joints Fsw building height 20-100m
Fv=
1
Wind load/ panel = 0.6 * 1.00 * 1.1 = 0.66 kN
Anchor load FH = 2 * 0.25 * 0.66 = 0.5 * 0.66
Fsw/1 Fsw/1
kN = 0.33kN

One anchor carries the wind loading of halph

Natural-stone half-panel.

Restraint Only Load Bearing

Restraint

23
www.sfsp-ikk.com
TYPES OF
LOADS

25
WIND LOADS
Wind Load for Cladding Facade According to Din 1055 Part 4

wind pressure q(kN/m2) wind suction

1.30 100m
100m ws = -2.60 ws = -0.91
wp = 1.04
Height of building

ws = -2.20 ws = -0.77
wp = 0.88 1.10
20m
20m ws = -1.60 ws = -0.56 8m
0.80
0.50 ws = -1.00 ws = -0.35
wp = 0.64 8m
wp = 0.40 b

wind pressure= wp = cp x q
cp = aerodymnamic pressure coefficient

-2.0
Lee -0.5
Cp -0.7

-0.7 -0.7
b Cp-values wind wind
Cp Cp b Cp-values wind
from frontside direction
from left -0.5
-2.0

-2.0
+0.8
0.8 x q
wind
Cp -0.7
Luv +0.8 direction
-2.0
A

A = building length Cp =
b = building width -0.7 for H/b > 0.5
H = Height of building -0.5 for H/b < 0.25
q = velocity pressure Values in between can be obtained by interpolation.
Wp = wind pressure
ws = wind suction

WIND LOAD ACCORDING TO DIN 1055

Wind Force Wind Velocity and wind Pressure

Height 0-8 >8 m - 20 m >20 m - 100 m >100 m
The total wind force wich act on a structure or m
component wind
W = Cf x q(ze) x A velocity 28,3 35,80 42,00 45,6
m/s
Cf = The aerodynamic Coefficient
qze = The velocity pressure at the reference height wind
A = The reference Area q 0,50 0,8 1,10 1,30
Kn/m2

26
Wind Suction Suction Coefficient in area of discontinuity
W=Cxq Increasing Coefficient Cp Width of a (m) Width of d (m)
C = Wind Coefficient a<8 m 1,0 m
q = Velocity Pressure -2,0 8 m < a ≤ 16 m a/8
a > 16,0 m 2,0 m
Wind Suction
Height 0-8m > 8 m - 20 m > 20 m - 100 m > 100 m
Wind -1,00 -1,60 -2,20 -2,60
kN/m2 (-2 x 0,5) (-2 x 0,8) (-2 x 1,1) (-2 x 1,30)

Wind Pressure = w = Cp x q Lateral Walls

aerodynamic Pressure Factor CP CP = -0,5 for H/W ≤ 0,25
Elevation Section CP = -0,7 for H/W ≤ 0,5
Plan Section Cp (B)
- 0.7 - 0.5

g
+ 0.8 - 0.5

in
wind
(B)

ild
direction Luv Lee
Lee (B)

Bu
H = height
g

+ 0.8 - 0.5
in

- 0.7 - 0.5
ild

Luv
Cp (B)
Bu

Wind pressure on corners

d = Corner (A) d

-2,0 - 0.5 (-0.7) (B)

g
W + 0.8 (B)

wind
in - 0.5
ild
CP = -2,0
Bu

d = 1m for A < 8 m
d = W/P for 8m < A < 16 m
d = 2,0 m for W > 16 m -2,0
- 0.5 (-0.7) (B)
(A) d
W

WIND LOAD ACCORDING TO DIN 1055

Vertical Joints Horizontal Joints

Fv Fv
FH FH

Fv= 1 panel Fv= 1/2 panel

FH= 1/2 panel FH= 1/2 panel

27
 Loads for Support Anchor
Characteristic weights of natural stone panels [kN/m²]
Density Plate thickness [cm]
kN/m³
2,0 3,0 4,0 5,0 6,0 7,5
20 0,40 0,60 0,80 1,00 1,20 1,50
24 0,48 0,72 0,96 1,20 1,44 1,80
25 0,50 0,75 1,00 1,25 1,50 1,88
26 0,52 0,78 1,04 1,30 1,56 1,95
27 0,54 0,81 1,08 1,35 1,62 2,03
28 0,56 0,84 1,12 1,40 1,68 2,10
30 0,60 0,90 1,20 1,50 1,80 2,25

Characteristic loads per panel [kN] by panel thickness 3cm and stone density 26kN/m³ (0,78kN/m2)
self Size Wind pressure FH Wind suction FH (A) Wind suction FH (B)
weight m² kN kN kN
kN
0-8m 8-20m 20-100m 0-8m 8-20m 20-100m 0-8m 8-20m 20-100m

0,3 0,38 0,15 0,25 0,34 -0,38 -0,62 -0,85 -0,13 -0,22 -0,30

0,6 0,77 0,31 0,49 0,68 -0,77 -1,23 -1,69 -0,27 -0,43 -0,59
0,9 1,15 0,46 0,74 1,02 -1,15 -1,85 -2,54 -0,40 -0,65 -0,89
1,2 1,54 0,62 0,98 1,35 -1,54 -2,46 -3,38 -0,54 -0,86 -1,18
1,5 1,92 0,77 1,23 1,69 -1,92 -3,08 -4,23 -0,67 -1,08 -1,48
1,8 2,31 0,92 1,48 2,03 -2,31 -3,69 -5,08 -0,81 -1,29 -1,78

Characteristic loads per panel [kN] by panel thickness 4cm and stone density 28kN/m³ (1,12kN/m2)
self Size Wind pressure FH Wind suction FH (A) Wind suction FH (B)
weight m² kN kN kN
kN
0-8m 8-20m 20-100m 0-8m 8-20m 20-100m 0-8m 8-20m 20-100m

0,4 0,36 0,14 0,23 0,31 -0,36 -0,57 -0,79 -0,13 -0,20 -0,28

0,8 0,71 0,29 0,46 0,63 -0,71 -1,14 -1,57 -0,25 -0,40 -0,55
1,2 1,07 0,43 0,69 0,94 -1,07 -1,71 -2,36 -0,38 -0,60 -0,83
1,6 1,43 0,57 0,91 1,26 -1,43 -2,29 -3,14 -0,50 -0,80 -1,10
2,0 1,79 0,71 1,14 1,57 -1,79 -2,86 -3,93 -0,63 -1,00 -1,38
2,4 2,14 0,86 1,37 1,89 -2,14 -3,43 -4,71 -0,75 -1,20 -1,65

SEISMIC LOAD ACCORDING TO UBC

Seismic Load
Seismic loading is one of the basic concept of earthquake engineering which means application of an
earthquake generated agitation to a structure. It happens at contact surface of a structure either with the ground
or with adjacent structure:
(2.5 x Ca x I)
= SL = D, SL ≥ 0.11 Ca x I x D
R
SL = Seismic load, Ca = Seismic response spectrum = Lateral force value in 97 UBC table 160
I = Importance factor given in 97 UBC Table 16 K
R = Component response modification factor from 97 UBC Table 16N
D = Dead Load
It is common practice to oxpress the Seismic load as a percentage of dead load calculating only the coefficient term.

Zone Seismic Load Seismic Zone

1 0.06 7x D Zone Damage to Structure
2 0.122 x D 0 No Domage
3 0.2 x D 1 Minor
4 0.244 x D 2 Moderate
3 Major
4 Huge
28
 Table 16-K - Occupancy Category
Seismic Seismic Seismic
Occupancy
Occupancy or functions of Structure Importance Importance Importance
Category
Factor, l Factor1, lp Factor, lw
Group I, Division 1 Occupancies having surgery and emergency treatment areas
Fire and police stations, Garages and shelters for emergency vehicules and emrgency aircraft,
Structures and shelters in emergency - preparedness centers
1. Essential Aviation control towers, Structures and equipment in government communication centers and
1.25 1.50 1.15
facilities2 other facilities required for emergency response
Standby power - generating equipment for Category 1 facilities
Tanks or other structures containing housing or supporting water or other fire - suppression
material or equipment required for the protection of Category 1.2 or 3 structures.
Group H, Divisions 1, 2, 6 and 7 Occupancies and structures therein housing or
2. Hazardous supporting toxic or explosive chemicals or substances, Nonbuilding structures housing,
1.25 1.50 1.15
facilities supporting or containing quantities for toxic or explosive substances that, if contained within a
building, would cause that building to be classified as a Group H, Division 1, 2 or 7 Occupancy
Group A, Divisions 1, 2 and 2.1 Occupancies
Buildings housing Group E, Divisions 1 and 3 occupancies with a capacity greater than 300
students, Buildings Housing Group B Occupancies used for college or adult education with a
3. Special
capacity greater than 500 students, Group I, Divisions 1 and 2 Occupancies with 50 or more
occupancy 1.00 1.00 1.00
resident incapacitated patients, but not included in Category I, Group I, Division 3 Occupancies
structures3
All structures with an occupancy greater than 5.000 persons
Structures and equipment in power-generating stations, and other public utility
facilities not included in Category 1 or Category 2 above, and required for continued operation
4. Standard
All structures housing occupancies or having functions not listed in Category
occupancy 1.00 1.00 1.00
1, 2 or 3 and Group U Occupancy towers
structures3
5. Miscellaneous
Group U Occupancies except for towers 1.00 1.00 1.00
structure

SEISMIC LOAD ACCORDING TO UBC

Table 16-N-Structural Systems1
HEIGHT LIMIT FOR
BASIC STRUCTURAL SEISMIC ZONES 3
LATERAL-FORCE-RESISTING SYSTEM DESCRIPTION R O AND 4 (feet)
SYSTEM 2
x 304.8 for cm

1. Light-framed walls with shear panels

a. Wood structural panel walls for structures three stories or less 5.5 2.8 65
b. All other light-framed walls 4.5 2.8 65
2. Shear walls
a. Concrete 4.5 2.8 160
1. Bearing wall system b. Masonry 4.5 2.8 160
3. Light steel-framed bearing walls with tension-only bracing 2.8 2.2 65

4. Braced frames where bracing carries gravity load

a. Steel 4.4 2.2 160
b. Concrete3 2.8 2.2 -
c. Heavy timber 2.8 2.2 65
1. Steel eccentrically braced frame (EBF) 7.0 2.8 240t

2. Light-framed walls with shear panels N.L.--no limit

a. Wood structural panel walls for structures three stories or less 6.5 2.8 65 1
Sec Section 1630.4 for combi-
b. All other light-framed walls 5.0 2.8 65 nation of structural systems.
3. Shear walls
2
Basic structural systems are
5.5 2.8 240
a. Concrete defined in Section 1629.6.
5.5 2.8 160
2. Building frame system b. Masonry 3
Prohibited in Seismic Zones 3
and 4.
4. Ordinary braced frames
a. Steel 5.6 2.2 160
4
1ncludes precast concrete con-
b. Concrete3 5.6 2.2 -- forrning to Section 1921.2.7.
c. Heavy timber 5.6 2.2 65
5
Prohibited in Seismic Zones 3
and 4, except as permitted in
5. Special concentrically braced frames Section 1634.2.
6.4 2.2 240
a. Steel 6
0rdinary moment-resisting
1. Special moment-resisting frame (SMRF) fi’ames in Seismic Zone 1 meet-
a. Steel 8.5 2.8 N.L. ing the requirements of
b. Concrete4 8.5 2.8 N.L. Section 2211.6 may use a R
value of 8.
2. Masonry moment-resisting wall frame (MMRWF) 6.5 2.8 160
3. Moment-resisting
7
Total height of the building
3. Concrete intermediate moment-resisting frame (IMRF) 5
5.5 2.8 -- including cantilevered columns.
frame system
4. Ordinary moment-resisting trame (OMRF)
8
Prohibited in Seismic Zones
a. Steel6 4.5 2.8 160 2A, 2B, 3 and 4. See Section
b. Concrete7 3.5 2.8 -- 1633.2.7.
5. Special truss moment frames of steel (STMF) 6.5 2.8 240

29
 HEIGHT LIMIT FOR
BASIC STRUCTURAL SEISMIC ZONES 3
LATERAL-FORCE-RESISTING SYSTEM DESCRIPTION R O AND 4 (feet)
SYS’TEM2
x 304.8 for cm
1. Shear walls 8.5 2.8 N.L.
a. Concrete with SMRF 4.2 2.8 160
b. Concrete with steel OMRF 6.5 2.8 160
c. Concrete with concrete IMRF5 5.5 2.8 160
d. Masonry with SMRF 4.2 2.8 160
e. Masonry with steel OMRF 4.2 2.8 --
f. Masomy with concrete IMRF3 6.0 2.8 160
g. Masonry with masonry MMRWF

2. Steel EBF
a. With steel SMRF 8.5 2.8 N.L.
4. Dual systems b. With steel OMRF 4.2 2.8 160

3. Ordinary braced frames

a. Steel with steel SMRF 6.5 2.8 N.L.
b. Steel with steel OMRF 4.2 2.8 160
c. Concrete with concrete SMRF3 6.5 2.8 --
d. Concrete with concrete 1MRF3 4.2 2.8 --

4. Special concentr.ically braced frames 7.5

2.0 N.L.
a. Steel with steel SMRF 4.2
2.8 160
b. Steel with steel OMRF

5. Cantilevered column building

1. Cantilevered column elements 2.5 2.0 357
systems

6. Shear \vall-frame interaction systems 1. Concrete8 5.5 2.8 160

7. Undetined systems See Sections 1629.6.7 and 1629.9.2 -- -- --

SEISMIC LOAD ACCORDING TO UBC

Table 16-0-Horizontal Force Factors, Ap and Rp
ELEMENTS OF STRUCTURES AND NONSTRUCTURAL COMPONENTS AND EQUIPMENT1 ap Rp FOOTNOTE

1. Elements of Structures
A. Walls including the following:
(1) Unbraced (cantilevered) parapets. 2.5 3.0
(2) Exterior walls at or above the ground floor and parapets braced above
their centers of gravity 1.0 3.0 2
(3) All interior-bearing and nonbearing walls. 1.0 3.0 2
B. Penthouse (except when framed by an extension of the structural trame). 1.5 4.0
C. Connections for prefabricated structural elements other than walls. See also Section 1632.2. 1.0 3.0 3
2. Nonstructural Components
A. Exterior and interior Oll1amentations and appendages. 2.5 3.0
B. Chimneys, stacks and trussed towers supported on or projecting above the roof:
(l) Laterally braced or anchored to the structural frame at a point below their centers of mass. 2.5 3.0
(2) Laterally braced or anchored to the structural frame at or above their centers of mass 1.0 3.0
C. Signs and billboards. 2.5 3.0
D. Storage racks (include contents) over 6 feet (1829 mm) tall 2.5 4.0
E. Permanent floor-supported cabinets and book stacks more than 6 feet (1829 mm) in height (include contents). 1.0 3.0
F. Anchorage and lateral bracing for suspended ceilings and light fixtures. 1.0 3.0 3,6,7,8
G. Access floor systems. 1.0 3.0 4,5,9
H. Masonry or concrete fences over 6 feet (1829 mm) high. 1.0 3.0
I. Partitions.

3. Equipment
A. Tanks and vessels (include contents), including support systems. 1.0 3.0

B. Electrical. mechanical and plumbing equipment and associated conduit and ductwork and piping. 1.0 3.0 5,10,11,12,13,14,15,16
C. Any flexible equipment laterally braced or anchored to the strue-tural frame at a point below their center of mass. 2.5 3.0 5,10,14,15,16
D. Anchorage of emergency power supply systems and essential communications equipment. Anchorage and support
systems for battery racks and fuel tanks necessary for operation of emergency equipment. See also Section 1632.2. 1.0 3.0 17,18
E. Temporary containers with llammable or hazardous materials. 1.0 3.0 19

4. Other Components
A. Rigid components with ductile material and attachments. 1.0 3.0 1
B. Rigid components with nonduetile material or attachments. 1.0 1.5 1
C. Flexible components with ductile material and attachments. 2.5 3.0 1
D. Flexible components with nonductile material or attachments. 2.5 1.5 1
30
 Table 16-Q-Seismic Coefficient Ca
SOIL PROFILE SEISMIC ZONE FACTOR, Z
TYPE Z= 0.075 Z= 0.15 Z= 0.2 Z= 0.3 Z= 0.4
SA 0.06 0.12 0.16 0.24 0.32Na
SB 0.08 0.15 0.20 0.30 0.40Na
SC 0.09 0.18 0.24 0.33 0.40Na
SD 0.12 0.22 0.28 0.36 0.44Na
SE 0.19 0.30 0.34 0.36 0.36Na
SF See Footnote I

Site-specific geotechnical investigation and dynamic site response analysis shall be perfomled to determine seismic coefficients tor Soil Profile
1

Type SF
I
See Sectlon 1627 for definitions of flexible components and rigid components.
2
See Sections 1633.2.4 and 1633.2.8 for concrete and masonry walls and Section 1632.2 for connections for panel connectors for panels.
3
Applies to Seismic Zones 2,3 and 4 only.
4
Ground supported steel storage racks may be designed using the provisions of Section 1634. Chapter 22, Division VI, may be used for design,
provided seismic design forces are equal to or greater than those specified in Section 1632.2 or 1634.2, as appropriate.
5
Only attachments, anchorage or restraints need be designed.
6
Ceiling weight shall include all light fixtures and other equipment or partitions that are laterally supported by the ceiling. For purposes of
determining the seismic force, a ceiling weight of not less than 4 psf (0.19 kN/m2) shall be used.
7
Ceilings constructed of lath and plaster or gypsum board screw or nail attached to suspended members that support a ceiling at one level
extending from wall to wall need not be analyzed, provided the walls are not over 50 feet (15 240mm) apart.
8
Light fixtures and mechanical services installed in metal suspension systems for accoustical title and lay-in panel ceilings shall be independently
supported from the structure above as specified in UBC Standard 25-2, part III.
w for access floor systems shall be the dead load of the access floor system plus 25 percent of the floor live load plus a 10-psf (0.48 kN/m2)
9 p

partition load allowance.

10
Equipment includes, but is not limited to, boilers, chillers, heat exchangers, pumps, air-handling units, cooling towers, control panels,
motors, switchgear, transformers and life-safety equipment. It shall include major conduit, ducting and piping, which services such
machinery and equipment and fire sprnkler systems. see section 163.2.2 for additional requirements for determining ap for nonrigid or
flexibly mounted equipment.
11
Seismic restraints may be omitted from piping and duct support if all the following conditions are satisfied:
11.1
Lateral motion of the piping or duct will not cause damaging impact with other systems.
11.2
The piping or duct is made of ductile material with ductile connections.
11.3
Lateral motion of the piping or duct does not cause impact of fragile appurtenances (e.g., sprinkler heads) with any other equipment,
piping or structural member.
11.4
Lateral motion of the piping or duct does not cause loss of system vertical support.
11.5
Rod-hung supports of less than 12 inches (305mm) in length have top connections that cannot develop moments.
11.6
Support members cantilevered up from the floor are checked for stability.

THERMAL MOVEMENTS
Thermal Movements
General
It is essential to take thermal movements into account. These are the relative changes in length and height due
to temperature differences between the cladding, and the structure to which the cladding is fixed. The magnitude
of the movements is dependent on whether the frame is entirely or partly inside the building envelope, the
ambient temperature, the coefficients of the thermal expansion of the various materials ( see the table), and the
temperature of the various components when the cladding is fixed.

For buildings in the KSA with modern standards of thermal insulation and air
conditioning, the temperatures tabulated in table KSA may be used as a guide to the
extremes likely to be experienced

31
 Material Coefficient of linear expansion 10^-6K^-1
)Steel ( and any concrete casing to steel members 12
Concrete
Dense gravel aggregate to 14 10
)Crushed rock (except limestone to 13 10
Limestone aggregate to 8 7
Lightweight aggregate to 12 8
Masonry
Concrete brickwork and blockwork to 12 6
Dense aggregate to 12 6
)Lightweight aggregate (autoclaved to 12 8
)Aerated (autoclaved 8

Calcium silicate brickwork to 14 8

Clay or shale brickwork or blockwork to 8 5
Natural stones
Limestone to 10 3
Sandstone to 12 7
Granite to 10 8
Slate to 12 6
Marble to 15 3
Quaritzte to 12 9

Thermal Movements
1- Example of Calculation of thermal movement:
Consider a Building Construction type is an enclosed Concrete frame with Granite cladding
(1000x500x30mm)
On a hot summer´s day with the building complete and occupied the relative movement (in mm/m) of frame to
cladding is given by the equation A =1000 [( tfs.tfe) Xf-(tcs-tce)Xc ]
tfs = is temperature (in °C) of frame in Summer
tfe = is temperature (in °C) of frame on erection
Xf = is coefficient of thermal expansion of frame
tcs = is temperature (in °C) of cladding in Summer
tce = is temperature (in °C) of cladding on erection
Xc = is coefficient of thermal expansion of cladding using the following values:
tfs = 30°C, tfe = 40°,Xf = 13x10^-6 per °C,tcs = 80°C, ce= 10°C,Xc =(8 to 10) x 10 ^-6 per °C
If Xc = 8 x 10^-6 per °C, movement = 1000[ (30-40) 13-(80-10)^8]
DL= 0,69mm/m, if Xc = 10, Dl = 0,83 mm/m in both cases , the movement shall be Coefficients Of Thermal Expansion
less than 1,0mm Material Linear expansion ‘
(in/°F)
Example Calculation of Deflection
Aluminium 0.0000133
Panel size : 1000mmx500mmx30mm
Brass 0.0000104
Granit with a density of 28 kN/m³
Deflection on the support anchor with a section of (width x height) 35mmx4mm Bronze 0.0000101

Existing deflection = f = (Fv.a³)/3xExI Bronze 0.0000096

Fv = Weight of cladding panel = 420 N Concrete 0.0000079
a = Cavity to pin in mm = 40mm Marble 0.0000073
E= Modulus of Elasticity of bracket = 170000 N/mm² Granite 0.0000078
I = Moment of Inertia = 35x4³/12 = 186,70mm^4 Lime stone 0.0000060
Allowable deflection f = (420Nx403 mm3) / 3x170000 N/mm2 x186,70mm^4) Masonry 0.0000035
f = 0,28 mm < 1.0mm
Mild steel 0.0000067
Thermal Expansion:
The thermal expansion of natural stone is an important consideration where natural stone is used with dissimilar
materials to form large units which are rigidly fixed.
The coefficient of thermal expansion varies from one variety of natural stone to another, so theactual thermal
characteristics of a specific natural stone should be obtained from the supplier when the final choice of a natural
stone is made.
Thermal expansion is calculated as follows: ∆L = α . h . ∆T ~0.5 mm/m
Where
∆L Change in height of panel in [mm]
α: Coefficient of thermal expansion in
[mm/mm/°C]
h: Height of panel in [mm]
∆T: Change in temperature in [°C]
We need joints, allowable movement thermal expansion

32
TYPES OF
FIXINGS

www.sfsp-ikk.com
 Principles for the Fixing of Building Cladding

The fixing systems for building claddings are composed of several elements (angles, expansion bolts,
screws, nuts, washers, etc), each of which shall present the appropriate mechanical features in respect to
the requirements posed by the specific project.

Any type of cladding, once fixed, is subject to two primary types of load:

- The permanent load (the dead load), due to the weight of the cladding itself;
- The variable load (applied loads), due to the wind, thermal expansions, seismic motions, etc.

Two fundamental types of fixing systems result:

- Load-bearing fixing: to support the permanent load and the vertical components of the variable loads.
- Restraining fixing: to support the horizontal components of the loads.

Load-bearing fixing are usually composed by

angles (of adequate dimensions), firmly fixed
to the building by the opportunely selected
anchoring element complete with expansion
anchors and bolts.

Restraining fixings instead, serve to maintain

the slabs in the positions specified by the project
design .Thanks to the system of adjustment with
which they are equipped, the absence of perfect
verticality in the external surfaces may be easily
overcome.

34
 L-Bracket (Standard & Serrated) | Type ST- 500 1100 With Pin

a b L-Bracket Holder With Pin

a Cavity to back side panel
b Panel thickness
T 1.5cm
2 cm T Bracket thickness
e d Diameter of pin
Leg b

e Cavity to pin
Hex bolt /
Leg a ~ Economic for 20 < a ≤ 80mm
Anchor

L-Bracket (Standard & Serrated) | Type ST- 500 1200 Up and Down

a b
L-Bracket Holder Up and Down
a Cavity to back side panel
T 1.5cm b Panel thickness
2 cm
T Bracket thickness
e Cavity to pin
Leg b

Hex bolt / e Economic for 20 < a ≤ 80mm

Anchor
Leg a ~

L-Bracket (Standard & Serrated) | Type ST- 500 1300 Up

a b L-Bracket Holder Up
a Cavity to back side panel
b Panel thickness
T Bracket thickness
e Cavity to pin
T 1.5cm Economic for 20 < a ≤ 80mm
2 cm
d
Leg b

Hex bolt / Leg a ~

Anchor
e

35
` L-Bracket (Standard & Serrated) | Type ST- 500 1400 Down

T L-Bracket holder down

1.5cm a Cavity to back side panel
2 cm
Leg b

b Panel thickness
Hex bolt / Leg a ~
Anchor T Bracket thickness
e Cavity to pin
d Economic for 20 < a ≤ 80mm
e

a b

L-Bracket (Standard & Serrated) | Type ST- 500 1500 With Two Pins

a b L-Bracket holder with pin

a Cavity to back side panel
b Panel thickness
T 1.5cm
2 cm T Bracket thickness
e d Diameter of pin
Leg b

e Cavity to pin
Hex bolt /
Leg a ~ Economic for 20 < a ≤ 80mm
Anchor

L-Bracket (Standard & Serrated) | Type ST- 500 1600 Double Up and Down

a b L-Bracket holder up and down

a Cavity to back side panel
b Panel thickness
T 1.5cm
2 cm T Bracket thickness
e Cavity to pin
Leg b

Economic for 20 < a ≤ 80mm

Hex bolt / e
Anchor
Leg a ~

36
` L-Bracket (Standard & Serrated) | Type ST- 500 1700 With Curved Leg

a b L-Bracket holder Curved

a Cavity to back side panel
T b Panel thickness
T Bracket thickness
1.5cm Economic for 20 < a ≤ 80mm
2 cm
Leg b

Hex bolt /
Anchor Leg a ~

Z-Bracket with returned Leg Horizontal joint (Staandard & Serrated) | Type ST- 600 1100

a b Z-returned bracket
a Cavity to back side panel
T 1.5cm b Panel thickness
2 cm
Leg a ~ e T Bracket thickness
d Diameter of pin
Leg b

Hex bolt / e Cavity to pin

Anchor
o
f Flat head parts
75 FHB
g Threaded part
Economic for 50 < a ≤ 120mm
d
n g f

Omega Bracket (Standard & Serrated) | Type ST- 700 1100

Z-returned bracket
a Cavity to back side panel
Hex bolt /
Anchor b Panel thickness
T Bracket thickness
T d Diameter of pin
e Cavity to pin
f Flat head parts
e a
g g Threaded part
Economic for 50 < a ≤ 120mm
f
d b

37
` Fishtail with Pin | Type ST- 800 1100

i a b Fishtail with Pin

a Cavity to back side panel
b Panel thickness
e T Bracket thickness
d Diameter of pin
e Cavity to pin
T i Embedment in wall
T Fish tail thickness
d Economic for 20 < a < 80mm

Fishtail Up & Down | Type ST- 800 1200

i a b Fishtail Up & Down

a Cavity to back side panel
b Panel thickness
e T Bracket thickness
d Diameter of pin
e Cavity to pin
T i Embedment in wall
T Fish tail thickness
d Economic for 20 < a < 80mm

Corrugated dowel | Type ST- 900 1100

i a b Corrugated dowel
a Cavity to back side panel
b Panel thickness
e T Bracket thickness
d Diameter of pin
e Cavity to pin
T i Embedment in wall
T Fish tail thickness
economic for 20 < a < 80mm
d

38
` Flat-Head-Bolt Direct in Wall

a b Flat-Head-Bolt direct in wall

a Cavity to back side panel
b Panel thickness
T Bracket thickness
e d Diameter of pin
T
Leg b

e Cavity to pin
f Flat head parts
g Rounded part
economic for 10 < a ≤ 60mm
g f d

Flat-Head-Bolt in C-Channel

a b Flat-Head-Bolt in C-Channel
a Cavity to back side panel
b Panel thickness
T Bracket thickness
T d Diameter of pin
e Cavity to pin
FHB f Flat head parts
g Rounded part
economic for 10 < a ≤ 60mm
g f d
e

39
 Metals Used in Fixing Systems

The metals used for the realization of the various components comprising the fixing system set shall possess
special features which, in addition to assuring a satisfactory mechanical resistance, shall also be immune to the
varying forms of corrosion, in order to withstand both the static and dynamic load conditions to which they are
subject throughout installation and the harmful atmospheric conditions which may arise as well, with extreme
sturdiness and security.

Particular attention shall be dedicated to the phenomenon of galvanic corrosion, which comes about whenever a
more noble metal is placed into direct contact with another metal in the presence of an electrolyte (water containing
salts, acids or substances deriving from combustion).

Under such conditions, a chemical reaction takes place which tends to damage the less noble metal. Galvanic
corrosion is particularly dangerous whenever the mass of the noble metal is inferior to that of the more noble metal.
The ratio between these two masses, the direct-contact surface area, and the difference in potential between the
two metals, determine the degree of corrosion or deterioration.

For this reason, the material most commonly-advised for the realization of a complete set of fixings is Stainless
steel AISI 304 which, in addition to guaranteeing optimum mechanical resistance features, is suited to satisfactory
resistance even in particularly harsh environmental surroundings.

Several combinations of different metals may be acceptable, provided that the designer is aware of the specific
environmental conditions, and that the combination is compatible with the same. Below we provide a table showing
the compatibility of different metals, from which an initial indication regarding combinations may be obtained.

SFSP Anchor bolts

Surfaces of contact (metal) Stainless Aluminium bronze Brass Galvanized Cast iron
steel steel
Stainless steel
Aluminum bronze
Brass
Copper
Galvanized steel
Mild steel
Cast iron
Lead
Aluminium

Possibility to use these metals together in all conditions.

Possibility to use these metals together in dry conditions according to designer’sinstruction.
These metals shall not be used together.

40
 Design Criteria
The design for the supporting structures of buildings claddings should be based on some basic principles :
a) The shape and the material of the structure to which the cladding is to be anchored (concrete, hollow brick, etc);
b) The shape and the material of the facing to be anchored

Cladding type Design weight (kN/m3)

Ceramic, Tuff 20
Limestone conglomerate, 25
Nagelflue, Travertine 26
Dolomite, Sandstone, Greywake 27
Granite, Porphyry, Syenite, Slate, Limestone, Marble 28
Basalt, Diorite, Gabbro, Gneiss 30

Thickess T
Height H
Width W

c) The forces to which the building itself may be subject (winds of particular intensity, seismic activity, etc);
d) 
The environmental surroundings in which the building is located, paying particular attention to harmful
atmospheric conditions which may be found in industrial, marine or other areas.
e) Arrangement of panel anchor in vertical or horizontal joint

The awareness and a complete analysis of these factors is a necessary condition for the correct planning, in order
to guarantee the highest safety levels possible.

41
INSTALLATION METHODS
The Dry Fixing Installation Method

The principle installation phases of a set of fixings for cladding is represented as follows:
1) Accurately locate the position of the drilling hole.
2) Drill a hole of the required depth and diameter.)
3) Insert the expansion bolt into the hole and cause it to expand by screwing down the nut A.
4) To regulate the distance, from the wall to the angle, rotate the screw B, while keeping the nut A
locked tightly in position. If necessary, to facilitate the operation, loosen the nut A, which will be
re-tightened at the end of the operation.
5) Tighten the lock-nut C for the final locking of the angle in the desired position.
6) Insert the pin in the angle to match the hole in the cladding slab.

1 2 3 4 5 6 7

A C
B

MOUNTING INSTRUCTIONS FOR STANGLE MORTAR ANCHOR (WET

FIXING)

Arrangement of Anchors in Vertical Joint Start at left edge

of the building
Take exact measurements of building, allowing for existing tolerances. Make
sufficiently large recesses in thermal insulation for natural-stone anchors.
Drill out anchor-pin holes and remove drilling dust. Erect support frame for support
bottom row of panels. Panel mounting starts at the left edge of the building. frame

Mount from left to right and from bottom to top.

Place first natural-stone panel on an anchor in horizontal joint and underlay support anchor
with wedge. Wet anchor holes and fill with cement mortar.
Insert anchor in the two anchor holes. Put anchor pin through anchor and
push into sliding sleeve. There shall be a clearance of about 2mm in the
sleeve for the anchor pin. Leave clear space of at least 2mm on side (sliding-
sleeve side) when inserting anchor. Pack mortar in anchor hole and re-insert Sliding sleeve
cut-out thermal insulation for exact fit. Fill anchor holes of second panel with
mortar, and then mount second panel, etc.
2mm 2mm Vertical joint
Mounting at right edge of building:
Anchor last panel but one at right edge, with pins on one side in vertical joint.
Mount last panel at right building-edge on 2 support anchors in horizontal Mounting at right edge
joint. of the building

2 support anchor

42
MOUNTING INSTRUCTIONS FOR STANGLE MORTAR ANCHOR (WET
FIXING)
Arrangemment of Anchors In Horizontal Joint

Take the exact measurements of the building façade, allowing for existing
tolerances. Cut out recesses in thermal insulation, sufficiently large for
natural-stone anchors. Drill anchor holes and remove drilling dust. Erect
2mm
support frame for bottom row of panels. Wet anchor holes and fill with
cement mortar. Insert support anchor for bottom row of panels and underlay 2mm

Sliding sleeve
with wedges.
Pack cements mortar in anchor holes. Insert cut-out thermal insulation for
exact fit. Drill anchor-pin holes in first-row panels and fill with mortar. Insert
sliding sleeve at top and then place natural-stone panel on support anchor;
align top edge of panel and fix provisionally and with wall hook, etc.
Insert support anchor for second row of panels.
Provide clear space of 2mm between top edge of bottom row of panels and
support anchor of second row.

wedge as
underlay

Mounting the first row of panels

INSTALLATION STEPS
Anchoring In Vertical Joint

1. Starting installation at the left hand of the building.

2. Position the first anchor under left bottom corner of the panel and install to the structure.
3. Position the first stone panel onto the first support anchor and wedge the right hand side.
4. Fasten the support anchor and restraint anchor for the first vertical joint and adjust.
5. Push the anchor Pin through the bracket and push into the sliding sleeve.
6. Fill the pin holes of the second stone panel with mortar
7. Push the second panel up to the first panel (leave a gap of 2mm on the sliding sleeve side)
8. Fit the next support anchor and restraint anchor.
9. Adjust and continue with the panel sequence
10. The second - last panel is anchored at the right - hand edge in the vertical joint with one-way pins.
11. The last panel at the right - hand edge of the building is placed onto 2 support anchors in the horizontal joint.

Anchoring in Horizontal Joint

1. Drill holes in the structure for the support anchors need for the first and second row of panels.
2. Align support anchors and fasten to the structure.
3. Fill the pin holes of the first panel with mortar and place the first panel on the bottom anchors.
4. Supporting the panel, adjust its second row support anchors to leave a gap (joint) of at least 2,5 mm between
the top edge of the panel and the under - side of the second row support anchors
5. Push the plastic sliding sleeve into the top pin through the bracket and into the sleeve below.
6. Working left to right repeat these steps for the first row and subsequent rows of the panels.

43
THE RANGE OF PRODUCTION
The problems inherent in the fixing of cladding and their respective solutions are confronted by SFSP/STANGLE
through either of two well-distinct approaches:
A) Standard fixing solutions:
W
 hich have been done in response to the most representative and demanded dimensional characteristics.
These products come to be illustrated in the chapter “Standard Types”.
B) Special fixing solutions:

For which SFSP/STANGLE has organized a staff of specialized techni cians, in grade to provide a series of
services at the complete disposal of the client. For greater detail, we shall illustrate these additional services to
which our clients may avail themselves, as follows:

- Consultant service - Designing service -Testing service -Quality control service

-Installation service

Consultant Service
SFSP/STANGLE puts its entire technical staff specialized in fixing systems, at the complete disposal of the
client, whenever indications regarding the most opportune decisions and methods to be adopted for the correct
realization of any cladding fixing project are required. In addition, upon the request of the client, technical visits
may be effected in the work yard, for the purposes of making realistic estimates, providing technical advice prior
to construction, or for a follow-up in regard to the correct utilization of the advised fixing systems.

Designing Service
SFSP/STANGLE can affect a performance study and the complete designing of the most opportune fixing
system for the cladding of buildings with marble facings, or facings of other materials.
The Design Department, after having received the essential information, will develop the project in respect to the
necessary specifications supplied by the client.
The primary objective is to provide by best solution to problems posed by the respective project.

Testing service
SFSP grants particular importance to this structure, without which it would be difficult to make and manage an
archive of knowledge that allows the preparation of new and advanced technical solutions to be subsequently
applied for the perfection and maximum reliability of each specific project. In order to attain this aim, an effective
system of collaboration has been evolved with testing centers.. In fact, SFSP is able to provide the documentation
belonging to the trial and testing of its own products, whenever requested by interested parties.

Quality control service

Quality represents one of the most essential characteristics of the finished product for SFSP.
In accordance with this concept, the company invests energy, which results in additional advantages for
the client. Control operations effected upon the raw material, upon the half-finished work-piece, and further
verifications upon the finished product, mean guarantees in regard to the component materials, exact conformity
with the desired dimensional features, and the faultless realization of even the smallest details.

Installation Service
SFSP is also ready to provide assistance service and to carry out the laying of the building cladding with
specialized personnel. Our technical staff is at your complete disposal in order to supply any further clarification
you should desire.

Product range
SFSP Steel angle range covers a wide variety of cavity, widths and load capacity. The steel angle consists of two
main components, a bracket with a vertical slot, and a threaded flat head bolt with dowel pin. The vertical slot
allows for up and down adjustment for connecting to the structure. The threaded flat head bolt allows in and
out adjustment to accommodate variations in cavity wide steel angle can be bolted to C-Channel for maximum
adjustment, or installed using drilled bolts. Steel angles are available in several configurations with a choice of
either full or half dowel pins. Full dowel pins have a nurled zone to prevent the pin dropping through the hole in
the flat head bolt.

44
INTERNATIONAL STANDARDS FOR CLADDING DESIGN
Design & Calculation Standards
Reference is made to the following standards for the design and
structural calculations of Natural Stone Fixing Systems.

British Standards:
BS 8298 Design and installation of natural stone cladding.
BS 1449 Part 2 Steel plates, sheets and strips stainless and heat resisting.
BS 6105 Corrosion resistant stainless steel fasteners.
BS 5950 Structural use of steel work in building.
CP3, Chapter 5, Part 2 Wind loads.
BS 970 Part 3 1991, M Mechanical properties for stainless steel.

German Standards:
DIN 1045 Concrete and reinforced concrete, design and dimensioning.
DIN 1053 Masonry, design and dimensioning.
DIN 1055 Design loads for buildings.
DIN 18 516 Cladding for external walls.
DIN 18 800 Steel structures, design and dimensioning.
DIN 18 801 Steel framed structures.

American Standards:
ASTM A 276 Standard specification for stainless steel bars and shapes.
ASTM 666 Standard specification for annealed or cold-worked
austenitic stainless steel sheets.
Uniform Building Code 1997-Volume 2

45
L- BRACKETS

www.sfsp-ikk.com
STANDARD TYPES
Support Bracket
The structural analysis fully considers the dead load of panel, imposed wind loads and thermal stresses, in
accordance with relevant DIN standards.

Loads caused by earthquakes can be

transferred into the anchoring base.

The support and restraint brackets are Fixed

using expansion anchors, chemical anchors,
etc.

Using expansion bolts, an installation of

the facade is also possible during the winter
months.

Due to the small drill hole dimensions of the

expansion bolts, the facade can be installed
very quickly.

47
L- BRACKETS ST-500
L - Brackets

Type ST- 500 1100 Type ST- 500 1200

F T
With Pin Angle Up and Down Angle F T
G
G
B
B

A C
E C
A
H

Type ST- 500 1300 Type ST- 500 1400

F T
Up Angle F T Down Angle
G
G
B
B

H
A C
A C H

Load Table for ST-1100/1200/1300/1400/1700.

Materials: SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50oc 24h average temperature

Leg B Cavity to Pin Deadload Windload Bracket Width Bracket Thickness Anchor
Ø Pin
B C max DL max WL ± A T comb. Force
mm
mm mm kN kN mm mm kN*
45 30 35 2 4 1.40
45 35 40 2 4 1.60
45 40 0.06 0.11 35 3 4 1.70
45 45 35 3 4 1.90
45 50 35 3 4 2.00
45 30 35 3 4 2.30
45 35 35 3 4 2.60
45 40 0.09 0.17 35 3 4 2.80
45 45 35 3 4 3.10
45 50 40 3 4 3.30
45 30 40 3 4 3.60
45 35 40 3 4 4.00
45 40 0.15 0.28 35 4 4 4.40
50 45 35 4 4 3.40
50 50 35 4 4 3.70
45 30 35 4 4 4.60
45 35 35 4 4 5.10
45 40 0.20 0.33 35 4 4 5.60
50 45 40 4 4 4.40
50 50 40 4 4 4.70

Loads per 1 bracket

If loads are bigger or dimensions are different, an individual calculation is necessary
* with safety 3.0

48
 Type ST- 500 1500 Type ST- 500 1600
With Two Pins T F
Double Up and Down
T
G F
G

J
B
K B
I L
A C
C A K H

Type ST- 500 1700

With Curved Leg F T

G
B

H C

Load Table for ST-1500/1600.

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG £ 50°C 24h average temperature
Leg B Cavity to Pin Deadload Windload Bracket Width Bracket Thickness Anchor
Ø Pin
B C max DL max WL ± A S comb. Force
mm
mm mm kN kN mm mm kN*
50 30 120 3 2x 4 5,80
50 35 120 3 2x 4 6,30
50 40 0,40 0,56 120 3 2x 4 6,80
50 45 140 3 2x 4 7,30
50 50 120 4 2x 4 8,90
50 30 120 3 2x 4 8,10
50 35 130 3 2x 4 8,90
50 40 0,50 0,70 120 4 2x 4 9,60
50 45 120 4 2x 4 10,40
50 50 120 4 2x 4 11,10
60 30 140 3 2x 4 7,00
60 35 120 4 2x 4 7,90
60 40 0,60 0,84 120 4 2x 4 8,40
60 45 120 4 2x 4 8,90
60 50 120 4 2x 4 9,40
60 30 120 4 2x 4 8,60
60 35 120 4 2x 4 9,20
60 40 0,70 0,98 120 4 2x 4 9,80
60 45 130 4 2x 4 10,40
60 50 140 4 2x 4 11,00

Loads per 1 bracket

If loads are bigger or dimensions are different, an individual calculation is necessary
* with safety 3,0

49
SYSTEM TYPE ST 500 -1100 WITH PIN
e

Fv e T b

FHZ n

FHD

Ød

b a

l c
K

Øf

Fv perm = permissible vertical loading capacity

FR = existing load on the dowel with maximum load of the anchor

Anchoring base: acc. To the licence of the dowel chosen.

50
 L-Bracket (Standard & Serrated) | Type ST- 500 1100 With Pin

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG,

S235JR-HDG ≤ 50°C 24h average temperature Standard
Items:

F T

E
C
A

51
SYSTEM TYPE ST 500 -1200 WITH UP & DOWN LEGS
L-Bracket (Standard & Serrated) | Type ST- 500 1200 Up and Down

Materials SS304, SS316, SS316L, SS316TI, S235JR- T

F
MG, S235JR-HDG ≤ 50°C 24h average temperature

Standard Items: G

A C

Item No. T A B C H sl hole

1200-35.45.30.2 2 35 45 30 15 6,5 x 22
1200-40.45.35.2 2 40 45 35 15 6,5 x 22
1200-35.45.30.3 3 35 45 30 15 6,5 x 22
1200-40.45.30.3 3 40 45 30 15 8,5 x 22
1200-35.45.35.3 3 35 45 35 15 6,5 x 22
1200-40.45.35.3 3 40 45 35 15 8,5 x 22
1200-35.45.40.3 3 35 45 40 15 6,5 x 22
1200-35.45.30.4 4 35 45 30 15 8,5 x 22
1200-35.45.35.4 4 35 45 35 15 8,5 x 22
1200-35.45.40.4 4 35 45 40 15 8,5 x 22
1200-35.50.45.4 4 35 50 45 15 8,5 x 22
1200-40.50.45.4 4 40 50 45 15 8,5 x 22

52
SYSTEM TYPE ST 500 -1300 WITH UP LEG
L-Bracket (Standard & Serrated) | Type ST- 500 1300 Up

Materials SS304, SS316, SS316L, SS316TI, S235JR-

MG, S235JR-HDG ≤ 50°C 24h average temperature F T

Standard Items:
G

A
C

Item No. T A B C H sl hole

1100-35.45.30.2 2 35 45 30 4 6,5 x 22
1100-40.45.35.2 2 40 45 35 4 6,5 x 22
1100-35.45.30.3 3 35 45 30 4 6,5 x 22
1100-40.45.30.3 3 40 45 30 4 8,5 x 22
1100-35.45.35.3 3 35 45 35 4 6,5 x 22
1100-40.45.35.3 3 40 45 35 4 8,5 x 22
1100-35.45.40.3 3 35 45 40 4 6,5 x 22
1100-35.45.30.4 4 35 45 30 4 8,5 x 22
1100-35.45.35.4 4 35 45 35 4 8,5 x 22
1100-35.45.40.4 4 35 45 40 4 8,5 x 22
1100-35.50.45.4 4 35 50 45 4 8,5 x 22
1100-40.50.45.4 4 40 50 45 4 8,5 x 22

53
SYSTEM TYPE ST 500 -1400 WITH DOWN LEG
L-Bracket (Standard & Serrated) | Type ST- 500 1400 Down

Materials SS304, SS316, SS316L, SS316TI, S235JR- F T

MG, S235JR-HDG ≤ 50°C 24h average temperature

Standard Items: G

A
C

Item No. T A B C H sl hole

1200-35.45.30.2 2 35 45 30 15 6,5 x 22
1200-40.45.35.2 2 40 45 35 15 6,5 x 22
1200-35.45.30.3 3 35 45 30 15 6,5 x 22
1200-40.45.30.3 3 40 45 30 15 8,5 x 22
1200-35.45.35.3 3 35 45 35 15 6,5 x 22
1200-40.45.35.3 3 40 45 35 15 8,5 x 22
1200-35.45.40.3 3 35 45 40 15 6,5 x 22
1200-35.45.30.4 4 35 45 30 15 8,5 x 22
1200-35.45.35.4 4 35 45 35 15 8,5 x 22
1200-35.45.40.4 4 35 45 40 15 8,5 x 22
1200-35.50.45.4 4 35 50 45 15 8,5 x 22
1200-40.50.45.4 4 40 50 45 15 8,5 x 22

54
SYSTEM TYPE ST 500 -1500 WITH DOUBLE PIN
L-Bracket (Standard & Serrated) | Type ST- 500 1500 With Two Pins

Materials SS304, SS316, SS316L, SS316TI, S235JR-

MG, S235JR-HDG ≤ 50°C 24h average temperature

Standard Items: T
F

A
C

Item No. T A B C Pin sl hole

1500-120.50.30.3 3 120 50 30 2x 4 8,5 x 22
1500-120.50.35.3 3 120 50 35 2x 4 8,5 x 22
1500-120.50.40.3 3 120 50 40 2x 4 8,5 x 22
1500-140.60.30.3 3 140 60 30 2x 4 8,5 x 22
1500-140.50.45.3 3 140 50 45 2x 4 8,5 x 22
1500-120.60.30.4 4 120 60 30 2x 4 8,5 x 22
1500-120.60.35.4 4 120 60 35 2x 4 8,5 x 22
1500-120.50.40.4 4 120 50 40 2x 4 10,5 x 22
1500-120.50.45.4 4 120 50 45 2x 4 10,5 x 22
1500-120.50.50.4 4 120 50 50 2x 4 8,5 x 22
1500-120.60.50.4 4 120 60 50 2x 4 10,5 x 22
1500-140.60.50.4 4 140 60 50 2x 4 10,5 x 22

55
SYSTEM TYPE ST 500 -1600 WITH DOUBLE UP & DOWN LEGS
L-Bracket (Standard & Serrated) | Type ST- 500 1600 Double Up and Down

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50°C 24h

average temperature T

Standard Items: F
G

K B

L
C
A
K H
L= A/2
K=A/4

Item No. T A B C H L K sl hole

1600-120.50.30.3 3 120 50 30 15 A/2 A/4 8,5 x 22
1600-120.50.35.3 3 120 50 35 15 A/2 A/4 8,5 x 22
1600-120.50.40.3 3 120 50 40 15 A/2 A/4 8,5 x 22
1600-140.60.30.3 3 140 60 30 15 A/2 A/4 8,5 x 22
1600-140.50.45.3 3 140 50 45 15 A/2 A/4 8,5 x 22
1600-120.60.30.4 4 120 60 30 15 A/2 A/4 8,5 x 22
1600-120.60.35.4 4 120 60 35 15 A/2 A/4 8,5 x 22
1600-120.50.40.4 4 120 50 40 15 A/2 A/4 10,5 x 22
1600-120.50.45.4 4 120 50 45 15 A/2 A/4 10,5 x 22
1600-120.50.50.4 4 120 50 50 15 A/2 A/4 8,5 x 22
1600-120.60.50.4 4 120 60 50 15 A/2 A/4 10,5 x 22
1600-140.60.50.4 4 140 60 50 15 A/2 A/4 10,5 x 22

56
SYSTEM TYPE ST 500 -1700 WITH CURVED LEG
L-Bracket (Standard & Serrated) | Type ST- 500 1700 With Curved Leg

Materials SS304, SS316, SS316L, SS316TI, S235JR-

MG, S235JR-HDG ≤ 50°C 24h average temperature

Standard Items: F T

C
H

Item No. T A B C H sl hole

1700-35.45.30.2 2 35 45 30 20 6,5 x 22
1700-40.45.35.2 2 40 45 35 20 6,5 x 22
1700-35.45.30.3 3 35 45 30 20 6,5 x 22
1700-40.45.30.3 3 40 45 30 20 8,5 x 22
1700-35.45.35.3 3 35 45 35 20 6,5 x 22
1700-40.45.35.3 3 40 45 35 20 8,5 x 22
1700-35.45.40.3 3 35 45 40 20 6,5 x 22
1700-35.45.30.4 4 35 45 30 20 8,5 x 22
1700-35.45.35.4 4 35 45 35 20 8,5 x 22
1700-35.45.40.4 4 35 45 40 20 8,5 x 22
1700-35.50.45.4 4 35 50 45 20 8,5 x 22
1700-40.50.45.4 4 40 50 45 20 8,5 x 22

57
Z- BRACKETS

www.sfsp-ikk.com
SYSTEM TYPE ST- 600 -1100 WITH RETURNED LEG
Z-Bracket with returned Leg

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG,

S235JR-HDG ≤ 50°C 24h average temperature Standard
Items:

Anchor bolt 1
Z-bracket 2
Pin 3
Nut 4
Flat head bolt 5
Plastic tube 6

Application Advantages hole dimensions of the anchors,

According to DIN 18515 all The panels are secured to the the facade can be installed very
cladding panels which are larger anchoring base material with quickly. The small size of drill
than 0.1 m2 have to be anchored. absolute safety. Manufactured hole into the anchoring base
from stainless steel. The material means that heavy
Material support and restraint brackets drilling equipment is not required.
Manufactured from stainless are adjustable in 2 directions.
steel AISI 304, 316, 316L and The brackets are fixed into the
316Ti. anchoring base by means of
Adjustability in two directions. anchors. Due to the small drill

59
SYSTEM TYPE ST- 600 -1100 WITH RETURNED LEG
Z-Bracket with returned Leg Horizontal joint (Standard & Serrated) | Type ST- 600 1100

e T

Fv

FR M
FHZ
N
FHD a±x
Ød

K
ØP
a Øf

Anchoring base: Adjustibility: FV perm. = permissible vertical

acc. to the licence of in 2 directions x = ± 10 mm loading capacity
the anchor bolt chosen. Z = ± 05 mm FH perm. = permissible horizontal
a = cavity to backside to panel t ensile load or
pressure load
FR = e  xisting load on
the anchor with
maximum

Z-Bracket with returned Leg Vertical joint (Standard & Serrated) | Type ST- 600 1100

e T

Fv

FR
FHZ m

FHD N
a±x
Ød

K
a
Ød
(Top View) Øf

60
SYSTEM TYPE ST- 600 -1100 WITH RETURNED LEG
Z-Bracket with returned Leg | ST-600-1100

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50°C 24h average temperature

Standard Items:

Item No. Width (W) Thickness (T) Offset (N) FHB Ø Pin sl hole
600-1100 -35.3.20 35 3 20 M8 4 6,5 x 22
600-1100 -40.3.30 40 3 30 M8 4 6,5 x 22
600-1100 -45.3.40 45 3 40 M8 4 6,5 x 22
600-1100 -50.3.50 50 3 50 M8 4 6,5 x 22
600-1100 -40.4.20 40 4 20 M10 5 8,5 x 22
600-1100 -40.4.30 40 4 30 M10 5 8,5 x 22
600-1100 -45.4.40 45 4 40 M10 5 8,5 x 22
600-1100 -50.4.50 50 4 50 M10 5 8,5 x 22
600-1100 -40.5.20 40 5 20 M12 6 8,5 x 22
600-1100 -45.5.30 45 5 30 M12 6 8,5 x 22
600-1100 -45.5.40 45 5 40 M12 6 8,5 x 22
600-1100 -50.5.50 50 5 50 M12 6 8,5 x 22

Load Table of Z-Bracket with returned Leg

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50°C 24h average temperature

Bracket Cavity to Pin Deadload Windload Bracket Bracket FHB Anchor

Ø Pin
Offset min - max max DL max WL ± Width Thickness (T) A2-70 comb. Force
mm
mm mm (e) kN kN mm mm A4-70 kN *
20 50-60 35 3 4 M8 1,90
30 60-70 40 3 4 M8 2,00
40 70-80 45 3 4 M8 2,10
0,16 0,21
50 80-90 50 3 4 M8 2,10
60 90-100 40 4 4 M8 2,10
70 100-110 40 4 4 M8 2,10
20 50-60 40 4 5 M10 3,40
30 60-70 40 4 5 M10 3,60
40 70-80 45 4 5 M10 3,60
0,28 0,37
50 80-90 50 4 5 M10 3,70
60 90-100 50 4 5 M10 3,70
70 100-110 55 4 5 M10 3,80
20 50-60 40 5 6 M12 6,00
30 60-70 45 5 6 M12 6,00
40 70-80 45 5 6 M12 6,10
0,45 0,66
50 80-90 50 5 6 M12 6,20
60 90-100 55 5 6 M12 6,30
70 100-110 60 5 6 M12 6,30

Loads per 1 bracket

If loads are bigger or dimensions are different, an individual calculation is necessary
* with safety 3,0

61
SYSTEM TYPE ST- 600 -1100 WITH RETURNED LEG
Z-Bracket with returned Leg Horizontal joint
The structural analysis fully considers the dead load of panel, imposed wind loads and thermal stresses, in
accordance with relevant DIN standards.

Loads caused by earthquakes can be transferred

into the anchoring base.

The support and restraint brackets are fixed using

expansion anchors, chemical anchors, etc.

The support and restraint brackets are adjustable in

2 directions.

Due to the adjustability of the brackets and the

small drill hole dimensions of the anchors, the
façade can be installed very
quickly.

The restraint anchors of the system 1 to 5 are

interchangeable so that any fixing problem can
optimally be solved.`

SYSTEM TYPE ST- 600 -1100 WITH RETURNED LEG

Z-Bracket with returned Leg Vertical joint
The structural analysis fully considers the
dead load of panel, imposed wind loads Support Bracket
and thermal stresses, in accordance with
relevant DIN standards.

Loads caused by earthquakes can be

transferred into the anchoring base.

The support and restraint brackets are

fixed using expansion anchors, chemical
anchors, etc.

The support and restraint brackets are

adjustable in 2 directions.

Due to the adjustability of the brackets

and the small drill hole dimensions of the
anchors, the façade can be installed very
quickly.

62
CASE STUDY

www.sfsp-ikk.com
PROOF FOR Z-RETURNED BRACKET ACCORDING TO DIN 18.800

a b Z-Returned Bracket
a Cavity to back side panel
T 1.5cm b Panel thickness
2 cm
Leg a ~ e T Bracket thickness
d Diameter of pin
Leg b

Hex bolt / e Offset to pin

Anchor f Flat head parts
o
75 FHB
g Threaded part
N Bracket offset

d
n g f

Facade Panel:
Bending detail: 50 Bending r: 6mm min.
15
4 Width = 800 mm
30
Height = 450 mm
4
Thickness = 30 mm

Cavity a = 40 ± 10 mm
Offset N = 15 mm
Cavity to Pin = 55 ± 10 mm

Facade Bracket:

Sec 1: min. w1 = 8 mm
t1 = 3 mm

Sec 2: thread = M8

Sec 3: w3 = 40 mm
t3 = 3 mm

Sec 4: d= 4.0 mm
l= >= 40 mm

Pieces in 1 joint: 2

64
 Structural Data

Node Numbering
Element Numbering

17
1218

11
12
2.00

DX = 6.50 Opposite Y-direction

14
1
X DX = 5.00
1
11
2.00

Z
DX = 1.50 DX = 3.20
13
DZ = 0.40

216
10 DX = 2.40
2
3 DX = 1.80

3
DZ = 3.00

6 8 9 7 8 6 7

5
DX = 4.20
DZ = 0.40

4
9510 1.259 cm
4

General Data
LC No LC Description Factor Combination Type Dead Weight

1 Proper weight 1,0 Permanent 1.00

2 Wind pressure 1,0 Variable -

3 Wind suction 1,0 Variable -

4 Seismic Load 1,0 Exceptional -

Load Groups
LG No LG Description Factor Safety 8M Load Cases in LG

1 1.00 1.10 1.35*LC1 + 1.50*LC2

2 1.00 1.10 1.35*LC1 + 1.50*LC3

3 1.00 1.10 LC1 + 1.50*LC3

4 1.00 1.10 LC1 + LC4

51 LC1 + LC2 ( for deflection) 1.00 1.10 LC1 + LC2

52 LC1 + LC3 ( for deflection) 1.00 1.10 LC1 + LC3

65
PROOF FOR Z-RETURNED BRACKET ACCORDING TO DIN 18.800
LOADS : LC 1 - Proper weight [kN] LOADS : LC 2 - Wind pressure [kN]

NODAL FORCES LC 1 NODAL FORCES LC 2

No Loaded Nodal Forces No Loaded Nodal Forces

Nodes Nodes
PX [kN] PY [kN] PZ [kN] PX [kN] PY [kN] PZ [kN]

1 7 0.000 0.000 0.15 1 7 0.2 0.000 0.000

1217
18
5
4 11
12

5 14
X 1
X
5 1
Z 11
Z
4 13
10216
5 2
4 3

4 Opposite Y-Direction 0.15

3
Opposite Y-direction

6 8 9 7 8 6 7
3 2 1
0.20
4
1.259 cm 5

4
4 9510
5 4

LOADS : LC 3 - Wind pressure [kN] LOADS : LC 4 - Seismic load [kN]

NODAL FORCES LC 3 NODAL FORCES LC 4

No Loaded Nodal Forces No Loaded Nodal Forces

Nodes Nodes
PX [kN] PY [kN] PZ [kN] PX [kN] PY [kN] PZ [kN]
1 7 0.2 0.000 0.000 1 7 0.000 0.05 0.000

1217
18

11
12

14
1
X X
Y
1
11 Z
Z

13
10216
2
3

Opposite Y-direction Isometric

3

6 8 9 7 8 6 0.20 7

5
1.259 cm 0.05
4
9510
4

66
PROOF FOR Z-RETURNED BRACKET ACCORDING TO DIN 18.800
LOAD COMBINATIONS

CO No CO Description Combination Criteria

1 LC1 or LC2 or LC3 or LC4 LG1 o LG2 o LG3 o LG4

Factor Number Eps-Convergence Ny-fold Tension

LG-No
Ny Iterations Existing Wanted Results Force Effect

LG1 1.000 71 .00E+00 0.01 Yes No

LG2 1.000 20 .25E-04 0.01 Yes No
LG3 1.000 20 .14E-04 0.01 Yes No
LG4 1.000 28 .92E-06 0.01 Yes No

LG51 1.000 61 .00E+00 0.01 Yes No

LG52 1.000 21 .16E-04 0.01 Yes No

RESULTS : LG 1 | Internal RESULTS : LG 2 | RESULTS : LG 3 |

Forces M-2 | Support Internal Forces M-2 | Internal Forces M-2 |
Reactions Support Reactions Support Reactions

0.04 0.22 0.19

0.04 0.22 0.19

0.18 0.62 0.52

0.07 X 0.44 X 0.38 X
0.21 0.21 0.15

Z -0.07 0.04 Z 0.05 Z

-0.36 -0.29
-0.22
-0.19
-0.22 -0.36 -0.22 -0.29
0.03 -0.22 -0.19
0.03
-1.03 -1.01 -0.75
-0.87 -0.85 -0.63
-0.38 -0.36 -0.27

0.85 -0.18 0.06 -0.69

0.19 -0.82
Opposite Y-direction Opposite Y-direction
Opposite Y-direction
-0.18 1.572kNcm 1.145kNcm
-0.04 1.542kNcm -0.01
0.18 Max M-2: 0.85, Min M-2: -1.03 kNcm 0.04
Max M-2: 0.44, Min M-2: -1.01 kNcm 0.01 Max M-2: 0.38, Min M-2: -0.75 kNcm

0.44 1.453 cm 1.453 cm 0.03 1.453 cm

0.10

RESULTS : LG 4 | RESULTS : LG 51 - LC1

Internal Forces M-2 | + LC2 ( for deflection) |
Support Reactions Deformations

0.09

0.33
0.2
Y X
Y X
0.05 0.15
0.220.16
0.16 Z
Z
0.34
0.11

0.09

Isometric
-0.25 -0.21
0.01
-0.09

Isometric Max u: 0.44 mm

Max M-3: 0.34, Min M-3: -0.25 kNcm Factor for Deformations: 40
0.507kNcm 0.507kNcm 0.44
0.20

67
PROOF FOR Z-RETURNED BRACKET ACCORDING TO DIN 18.800
RESULTS : LG 52 - LC1 + LC3 ( for def lection) | Deformations

Isometric
MAX/MIN/CORR SUPPORT FORCES AND SUPPORT
1.453 cm
MOMENTS
Support Forces [kN] Support Moments Y X
Max u: 0.48 mm
Node CO Factor for Deformations: 80
[kNcm]
No No
PX PY PZ MX MY MZ Z

Max P-X .62 .00 .21 .00 .00 .00

Min P-X .00 .00 .00 .00 .00 .00
LC in Max P-X: LG2
LC in Min P-X:
Max P-Y .29 .05 .15 -.22 .00 .33
Min P-Y .00 .00 .00 .00 .00 .00
LC in Max P-Y: LG4
LC in Min P-Y:
Max P-Z .18 .00 .21 .00 .00 .00
Min P-Z .00 .00 .00 .00 .00 .00
LC in Max P-Z: LG1 0.48
LC in Min P-Z:
1 CO1
Max M-X .00 .00 .00 .00 .00 .00 RESULTS : CO 1 - LC1
Min M-X .29 .05 .15 -.22 .00 .33
LC in Max M-X: or LC2 or LC3 or LC4
LC in Min M-X: LG4 | Max/Min Internal
Max M-Y .62 .00 .21 .00 .00 .00 Forces M-2
Min M-Y .00 .00 .00 .00 .00 .00
LC in Max M-Y: LG2
LC in Min M-Y:
Max M-Z .29 .05 .15 -.22 .00 .33
0.22
Min M-Z .00 .00 .00 .00 .00 .00
LC in Max M-Z: LG4
LC in Min M-Z: 0.44 X

Max P-X .00 .00 .00 .00 .00 .00

0.05 -0.07
Min P-X -.44 .00 .00 .00 .00 .00 Z
-0.36
LC in Max P-X:
LC in Min P-X: LG1 -0.36 -0.22
10 CO1 0.03 -0.22
Max P-Y .00 .00 .00 .00 .00 .00 0.03
-1.03
-0.87
Min P-Y -.20 .00 .00 .00 .00 .00 -0.38
LC in Max P-Y:
0.85 -0.82
LC in Min P-Y: LG4
Opposite Y-direction
Max P-X .00 .00 .00 .00 .00 .00 1.572kNcm
-0.18
Min P-X .00 .00 .00 .00 .00 .00
0.18
LC in Max P-X: Max M-2: 0.85, Min M-2: -1.03 kNcm
1.453 cm
LC in Min P-X: LG1
16 CO1
Max P-Y .00 .00 .00 .00 .00 .00
Min P-Y .00 .00 .00 .00 .00 .00
LC in Max P-Y:
LC in Min P-Y: LG4
Max P-X .00 .00 .00 .00 .00 .00
Min P-X -.22 .00 .00 .00 .00 .00
LC in Max P-X:
LC in Min P-X: LG2
18 CO1
Max P-Y .00 .00 .00 .00 .00 .00
Min P-Y .00 .00 .00 .00 .00 .00
LC in Max P-Y:
LC in Min P-Y:

68
 RESULTS : CO 1 - LC1 RESULTS : CO 1 - LC1 RESULTS : CO 1 - LC1
or LC2 or LC3 or LC4 or LC2 or LC3 or LC4 or LC2 or LC3 or LC4
| Max/Min Internal | Max/Min Internal | ExtremeSupport
Forces N Forces V-3 Reactions
0.22

0.22
0.22 0.22

0.21 X
0.22 -0.40
X
0.33 0.62
0.20 Z
X
-0.40 0.21
Z
0.22
0.20
0.20
Z
-0.40
-0.30 -0.30 -0.30 -0.30 -0.40
0.44 0.16
0.44 0.16
0.20 -0.20 -0.20 -0.21 -0.21
-0.43
-0.43 -0.40
-0.44
0.30 0.30 0.30 0.30
Opposite Y-direction
Opposite Y-direction Isometric
0.672kN 0.693kN 1.453 cm
-0.44
Max N: 0.44, Min N: -0.43 kN Max V-3: 0.22, Min V-3: -0.44 kN
1.453 cm 0.12 1.500 cm
0.12
0.12
0.44

STEEL1 - SPANNUNGSANALYSE| GENERAL DATA

All
LG1 1.35*LC1 + 1.50*LC2
ELEMENTS TO DESIGN
LOAD CASES TO DESIGN LG2 1.35*LC1 + 1.50*LC3
LG3 LC1 + 1.50*LC3
LG4 LC1 + LC4

Mat Material Material Allowable Stresses [kN/cm^2] at 50oc

No Description Code, Criterion
Sigma Tau Sigma eq
1 SS-304 Stainless Steel 16.1 9.3 17.7
2 A-70 Stainless Steel 40.9 23.6 40.9

Stress Elem x Loc S Point LC Stress [kN/cm^2] Stress

Type No [cm] No No Ratio
existing allowable

Section No 1 - Flat 8/3

Sigma Total 6 1.80 3 LG1 -32.92 40.90 0.80
Tau Total 6 0.00 5 LG1 1.31 23.60 0.06
Sigma eq 6 1.80 3 LG1 32.92 40.90 0.80

Section No 2 - Round 6.8

Sigma Total 7 2.40 28 LG1 -29.01 40.90 0.71
Tau Total 7 0.00 37 LG1 0.77 23.60 0.03
Sigma eq 7 2.40 28 LG1 29.01 40.90 0.71

Section No 3 - Round 13
Sigma Total 8 0.80 28 LG1 -5.00 16.10 0.31
Tau Total 8 0.00 37 LG1 0.20 9.30 0.02
Sigma eq 8 0.80 28 LG1 5.00 17.70 0.28

Section No 4 - Flat 40/3

Sigma Total 5 0.00 1 LG1 -14.17 16.10 0.88
Tau Total 13 0.00 1 LG 4 2.89 9.30 0.31
Sigma eq 5 0.00 1 LG1 14.17 17.70 0.80

Section No 5 - Flat 30/3

Sigma Total 1 0.00 3 LG2 10.01 16.10 0.62
Tau Total 1 0.00 1 LG4 3.91 9.30 0.42
Sigma eq 1 0.00 3 LG2 10.01 17.70 0.57

69
www.sfsp-ikk.com
 OMEGA
BRACKET

71
 Omega Bracket (Standard & Serrated) | Type ST- 700 1100

It is is designed for fastening the natural stone panel x

c
beneath a concrete floor slab.
m
Anchoring base: acc. to the licence of the anchor bolt chosen. T
N a±x
d
a
Adjustibility: Fv
in 2 directions x = ± 05 mm c
Z = ± 10 mm

FVperm = permissible vertical loading capacity K

FHperm.= permissible horizontal tensile load or pressure load
FR= existing load on the anchor with maximum load of the ØP Øf
bracket

FHB
Width (W ) Bracket Offset Ø Pin
Codes A2-70 sl hole
mm mm (N) mm
A4-70
700 1100-35.3.70 35 3 70 M8 4 6,5 x 22
700 1100-35.3.80 35 3 80 M8 4 6,5 x 22
700 1100-40.3.110 40 3 10 M8 4 6,5 x 22
700 1100-40.3.120 40 3 20 M8 4 6,5 x 22
700 1100-55.4.110 55 4 10 M10 5 8,5 x 22
700 1100-55.4.120 55 4 20 M10 5 8,5 x 22
700 1100-55.5.90 55 5 90 M12 6 10,5 x 22
700 1100-55.5.100 55 5 0 M12 6 10,5 x 22
700 1100-60.5.110 60 5 10 M12 6 10,5 x 22
700 1100-60.5.120 60 5 20 M12 6 10,5 x 22

Omega Brackets Load Table

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50C° 24h average temperature

Bracket Cavity to Pin Deadload Windload Bracket Bracket FHB Anchor

Ø Pin
Offset min - max max DL max WL ± Width Thickness (T) A2-70 comb. Force
mm
mm mm kN kN mm mm A4-70 kN *
70 100-110 30 3 4 M8 2.30
80 110-120 30 3 4 M8 2.40
90 120-130 35 3 4 M8 2.50
0.16 0.22
100 130-140 35 3 4 M8 2.50
110 140-150 40 3 4 M8 2.50
120 150-160 40 3 4 M8 2.60
70 100-110 55 3 5 M10 4.10
80 110-120 55 3 5 M10 4.20
90 120-130 50 4 5 M10 4.30
0.28 0.39
100 130-140 50 4 5 M10 4.40
110 140-150 55 4 5 M10 4.50
120 150-160 55 4 5 M10 4.60
70 100-120 50 5 6 M12 8.80
80 110-130 50 5 6 M12 9.00
90 120-140 55 5 6 M12 9.20
0.55 0.77
100 130-150 55 5 6 M12 9.40
110 140-160 60 5 6 M12 9.60
120 150-170 60 5 6 M12 9.80

Loads per 1 bracket

If loads are bigger or dimensions are different, an individual calculation is necessary with safety 3,0

72
FLAT HEAD BOLT TECHNICAL DETAILS
Flat Head Bolt

Materials A2-70, A4-70 ≤ 50°C 24h average tem-

perature Fixing in reinforced concrete vertical wall,
or steel substructure

Cavity to Pin Deadload Windload FHB

Ø Pin
min - max max DL max WL ± A2-70
mm
mm kN kN A4-70
20-30 M6 4
30-40 M6 4
0.08 0.11
40-50 M8 4
50-60 M8 4
30-40 M8 4
40-50 M8 4
0.16 0.22
50-60 M10 4
60-70 M10 4
30-40 M10 5
40-50 M10 5
0.23 0.32
50-60 M10 5
60-70 M10 5
30-40 M12 6
40-50 M12 6
0.45 0.63
50-60 M12 6
60-70 M12 6

According to DIN 18515 part 3

Pins: pin hole shall be 3mm bigger than pin diameter.
Pin distances (d<30): Distance between pannel corner and middle pinhole is min 2.5 the pannel thickness.

Support anchor

pin hole Ø d≥30

Sleeve
d/2 d/2
d

pin Ø b ≥ 10 x pin Ø b ≥ 10 x pin Ø d/2

73
FISHTAIL
BRACKET

www.sfsp-ikk.com
TYPE ST- 800 -1100
Fishtail with Pin | Type ST- 800 1100

Materials SS304, SS316, SS316L, SS316TI, S235JR- T

MG, S235JR-HDG ≤ 50°C 24h average temperature
Standard Items:

B
C L
w

Codes Width (W) Thickness (T) Length (L) sl hole

800-1100-25.2.100 25 2 100 4.1 x 15
800-1100-25.2.120 25 2 120 4.1 x 15
800-1100-25.2.140 25 2 140 4.1 x 15
800-1100-25.2.160 25 2 160 4.1 x 15
800-1100-25.3.100 25 3 100 4.1 x 15
800-1100-25.3.120 25 3 120 4.1 x 15
800-1100-25.3.140 25 3 140 4.1 x 15
800-1100-25.3.160 25 3 160 4.1 x 15
800-1100-30.4.100 30 4 100 5.1 x 15
800-1100-30.4.120 30 4 120 5.1 x 15
800-1100-30.4.140 30 4 140 5.1 x 15
800-1100-30.4.160 30 4 160 5.1 x 15

TYPE ST- 800 -1100

Fishtail Up & Down | Type ST- 800 1200

Materials SS304, SS316, SS316L, SS316TI, S235JR- T

MG, S235JR-HDG ≤ 50°C 24h average temperature
Standard Items:
B
w
C L
H

Codes Width (W) Thickness (T) Length (L) Height (H)

800-1200-25.2.100 25 2 100 15
800-1200-25.2.120 25 2 120 15
800-1200-25.2.140 25 2 140 15
800-1200-25.2.160 25 2 160 15
800-1200-25.3.100 25 3 100 15
800-1200-25.3.120 25 3 120 15
800-1200-25.3.140 25 3 140 15
800-1200-25.3.160 25 3 160 15
800-1200-30.4.100 30 4 100 15
800-1200-30.4.120 30 4 120 15
800-1200-30.4.140 30 4 140 15
800-1200-30.4.160 30 4 160 15

75
TYPE ST- 800 - 1200
Type ST- 800 (1100-1200) Fishtail (Pin & Up and Down)

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50°C 24h average temperature
Fixing in reinforced concrete vertical wall

Cavity to Pin Deadload Winload Bracket Bracket Ø Pin

Embedment Length
min - max max DL max WL ± Width Thickness A-70
mm mm
mm kN kN mm mm mm
40-50 25 2 4 45 100
50-60 25 2 4 55 120
0,10 0,14
60-70 25 2 4 65 140
70-80 25 2 4 75 160
40-50 25 3 4 45 100
50-60 25 3 4 55 120
0,22 0,31
60-70 25 3 4 65 140
70-80 25 3 4 75 160
40-50 30 4 5 45 100

50-60 30 4 5 55 120
0.29 0.41
60-70 30 4 5 65 140
70-80 30 4 5 75 160

Loads per 1 bracket

If loads are bigger or dimensions are different, an individual calculation is necessary

Type ST- 800 (1100-1200) Fishtail (Pin & Up and Down)

Materials SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50°C 24h average temperature
Fixing in solid blockwork vertical wall

Cavity to Pin Deadload Winload Bracket Bracket Ø Pin

Embedment Length
min - max max DL max WL ± Width Thickness A-70
mm mm
mm kN kN mm mm mm
40-50 25 2 4 45 100
50-60 25 2 4 55 120
0,08 0,11
60-70 25 2 4 65 140
70-80 25 2 4 75 160
40-50 25 3 4 45 100
50-60 25 3 4 55 120
0,13 0,18
60-70 25 3 4 65 140
70-80 25 3 4 75 160
40-50 30 4 5 45 100

50-60 30 4 5 55 120
0.20 0.28
60-70 30 4 5 65 140
70-80 30 4 5 75 160

Loads per 1 bracket

If loads are bigger or dimensions are different, an individual calculation is necessary

76
CORRUGATED
DOWEL

www.sfsp-ikk.com
TYPE ST- 900 -1100 (CORRUGATED DOWEL)
Corrugated dowel | Type ST- 900 1100

The Mortar Anchor is a restraint anchor and is used to

install last row of slabs on to concrete and
masonry walls at horizontal installation.
This anchor can be used for wind loads of up to 1000 N
and can be used on projection ,in addition that it can be
used both in horizontal and in vertical joints.

Load bearing and restraining corrugated stud.

Material: SS304, SS316, SS316L, SS316TI, S235JR-MG,
S235JR-HDG.

Load-bearing and retaining angles.

Material: SS304, SS316, SS316L, SS316TI, S235JR-MG, S235JR-HDG ≤ 50oc 24h average temperature

Standard items:

Stud Fixable Resin

0 0 0 Hole vol-
Net anchor CODE length Hole depth thickness volume
stud Hole inside ume
/EHD /EHD to inject

Type CODE dv/mm l/mm do/mm dv/mm ho/mm tfix/mm cm3 cm3
BE 12x45 8708955 M6-M8 65 12 10 45 - 5,1 5,1
BE 12x60 8708956 M6-M8 80 12 10 60 - 6,8 6,8
BE 12x80 8708957 M6-M8 110 12 10 70 10 9,1 9,1
BE 15x85 8708952 M8-M10 110-160 15 13 85 30-55 15,0 15,0
BE 15x130 8708953 M8-M10 160 15 13 130 10 23,0 23,0
BE 20x85 8708954 M12 115 20 18 85 10 26,7 26,7

BM 11x1000 8708961 M8 .var 12 9.5 .var - - -

BM 15x1000 8708962 M10 .var 16 13.5 .var - - -
BM 20x1000 8708963 M12 .var 22 19.0 .var - - -

Angles of different dimensions can be manufactured upon specific demand.

78
 ho Tfix

do dv

hef
lv

a b cc
aaa bbb cc
a- Drill to the b- Insert tube screen. c- Inject the resin with
suggested diameter. the special nozzle.

d e
ddd eee
d- insert the threaded e- After the hardening
stud turning it slowly. time fix the object.

0 Stud 0 0 Hole Fixable Hole Resin volume

Net anchor CODE stud length/ Hole inside depth thickness/EHD volume to inject
EHD

Type CODE dv/mm l/mm do/mm dv/mm ho/mm tfix/mm cm3 cm3
BE 12x45 8708955 M6-M8 65 12 10 45 - 5,1 5,1
BE 12x60 8708956 M6-M8 80 12 10 60 - 6,8 6,8
BE 12x80 8708957 M6-M8 110 12 10 70 10 9,1 9,1
BE 15x85 8708952 M8-M10 110-160 15 13 85 30-55 15,0 15,0
BE 15x130 8708953 M8-M10 160 15 13 130 10 23,0 23,0
BE 20x85 8708954 M12 115 20 18 85 10 26,7 26,7

BM 11x1000 8708961 M8 .var 12 9.5 .var - - -

BM 15x1000 8708962 M10 .var 16 13.5 .var - - -
BM 20x1000 8708963 M12 .var 22 19.0 .var - - -

79
www.sfsp-ikk.com
 EXAMPLES OF STEEL
BACK SUPPORT SYSTEM

81
EXAMPLES OF STEEL BACKSUPPORT SYSTEMS

Example -1
Front To Back Channel with welded back plate and up & down bracket

Example -2
Square tube with welded channel & double pin L-bracket

Example -3
Single channel with Omega support and Z-brackets

Example -4
B2B with Omega support and Z-brackets

Example -5
Cantilever Arm with BTB and Flate Head Bolt

82
EXAMPLE -1
Front To Back Channel with welded back plate and up & down bracket

Floor to floor System using front to back channels with support plates and L-Brackets up & down with bolts and
spring nuts fixed to the channels .
- Min cavity to backside of panel: 100 mm
- Span ≤ 3,0 mm

Hex Bolt With Spring Nut Through Bolt

(Wedge Anchor

L-Bracket (Standard) Front To Back Channel

Type ST- 500 1200 Up & Down with welded Support Plate

(A)

Detail (A)
total cavity

b 82 mm 10

83
EXAMPLE -2
Square tube with welded channel & double pin L-bracket

Floor to floor System using square tubes with channels and L-Brackets double pin type with bolts and spring
nuts fixed to the channels .

- Min cavity to backside of panel: 120 mm

- Span ≥ 3,0 mm

Through Bolt
(Wedge Anchor)
Hex Bolt With Spring Nut
Tube With Welded Channel
And Support Back Plate
L-Bracket (Standard )
Type ST- 500 1600 With Two Pins

(A)

Detail (A)

Total cavity

b 91 8

84
EXAMPLE -3
Single channel with Omega support and Z-brackets

Steel back-support system for large cavity using omega brackets, channels and Z- brackets with bolts and spring
nuts fixed to the channels and adjustable flat head bolts .

- For cavity ≥ 150 mm

- Distance of Omega brackets ~150 cm (=Span of channels)

Omega Support
C-Channel
Through Bolt
(Wedge Anchor)

Hex Bolt
With Spring Nut

Z-Bracket

Flat Head Bolt

With Pin

(A)

Detail (A)
Total Cavity
omega
41 offset

85
EXAMPLE -4
BTB with Omega Sapport and Z-brackets

Steel back-support system for large cavity using omega brackets, channels and Z- brackets with bolts and spring
nuts fixed to the channels and adjustable flat head bolts.

- For cavity ≥ 200mm

- distance of Omegabrackets ~200-300cm

Through Bolt (A)

(Wedge Anchor)
C-Channel
Omega Support

Hex Bolt
With Spring Nut

Z-Bracket
Flat Head
Bolt With Pin

Detail (A)
Total Cavity
90 Omega Offset

86
EXAMPLE -5
Cantilever Arm Support with BTB channel and Flate Head Bolt

Steel back-support system for Adjustable large cavities using support brackets, front to back channels,and adju-
stable flat head bolts with back plates and spring nuts fixed to channels .

- For cavity ≥ 300 mm

- Distance of Omega brackets ~3 cm (=Span of channels).

Hex Bolt with Nut (A)

Front to Back Channel

Support Brackets
Flat Head Bolt With
Back Plate and Spring Nut

Detail (A)
Total Cavity
Support Bracket Offset

b 82

87
TECHNICAL DETAILS
Detail solution: fixing of slabs at opening. ex . window

section 1

support anchor
type ST-600

restraint anchor
type ST-550

restraint anchor
type ST-550

Fixings positions as per DIN 18516 part3. special

Slabs will be held usually at 4 points. corner section 2
minimum at 3 points. bracket
Fixings positions have to allow the slab to
contract or expand freely when subjected to
temperature.
All fixing points have to be located on an
imaginary circle if drawn through these
points.

restraint anchor
type ST-500

88
C-CHANNELS
LOADS & SUPPORTS

www.sfsp-ikk.com
Channel Finishes
SFSP’s metal framing channel is
Standard Finishes: Pre-Galvanized
finish (ASTM A653M coating G90 CHANNEL HOLE
PATTERNS
cold formed on modern rolling
and G60). Hot Dip Galvanized
machines from low carbon steel
after fabrication (ASTM A123
manufactured according to BS
or BS EN ISO1461:2009). Other
6946:1988. A continuous slot PT Type Channel PT Plain Type
custom coatings are available upon
provides the ability to make
request. Part No Thick. Height “H”
attachments at any point. mm.
CCH-220 1.5 21.0
Lengths Z CCH-240 1.5 41.0
Standard length: 3000mm with ± CCH-260 1.5 25.0
3.2mm length tolerance. CCH-320 2.0 21.0
Z
Custom lengths vv available upon CCH-340 2.0 41.0
request.
CCH-360 2.0 25.0
CCH-420 2.5 21.0
Y Y Y Y CCH-440 2.5 41.0

METAL FRAMING CHANNELS CCH-460 2.5 25.0

Selection Chart

Part No Z
Channel Dimensions Thickness ST Type Channel ST Slotted Type
Height “H” Width “W” Part No Thick. Height “H”
Z
CCH - 220/221 21.0 mm 41.0 mm 1.5 mm mm.
CCH - 240/241 41.0 mm 41.0 mm 1.5 mm CCH-221 1.5 21.0
CCH - 260/261 25.0 mm 50.0 mm 1.5 mm CCH-241 1.5 41.0
CCH - 320/321 21.0 mm 41.0 mm 2.0Z mm Z Z CCH-261 1.5 25.0
CCH - 340/341 41.0 mm 41.0 mm 2.0
Z
mm Z CCH-321 2.0 21.0
Z
Z
CCH - 360/361 25.0ZZ mm 50.0 mm 2.0 mm CCH-341 2.0 41.0
Z
CCH-361 2.0 25.0
21.0 CCH - 420/421 Y21.0 mm 41.0 mm 2.5 mm
Y 41.0 Y Y

CCH - 440/441 Y
41.0
Y mm Y
41.0 mm
Y
Y
Y 2.5 mm Y CCH-421 2.5 21.0
Y

CCH - 460/461 Y
25.0
Y
mm Y
50.0 mm
YY Y
2.5 mm Y Y CCH-441 2.5 41.0
Z
41.0 CCH-461 2.5 25.0
Z
For Toothed Channel add “T” after the ZPart no. ex: CCH-220T
Z 41.0
Z Z

Z
Z
B2B Type Channel
B2B Type
3 2 0
Z Z

CCH 320 Part No Thick. Height “H”

22.0
T 22.0
Z
mm.
Z

Z Z Z
7.0 CCH-222 1.5 42.0
7.0
Z
CCH-242 1.5 82.0
Material Thickness
21.0 Y
Size
21.0
ZY
Y
Z
Channel
Y Patterns
Y
41.0 Y
Toothed
Y
Y

channel CCH-262 1.5 50.0

21.0 41.0
2 for 1.5 mm 21.0 Y 2 -Y 21/41Ymm
21.0 Y0 - PT41.0
41.0
Y
41.0 Y Y Y

3 for 2.0 mm 4 - Z41/4141.0mmZ 1 - ST CCH-322 2.0 42.0

4 for 2.5 mm41.0 6-
41.0
41.0
25/50
Z mm Z 2 - B2B Z
Z
41.0
CCH-342 2.0 82.0
41.0
Z
41.0 Z
41.0 41.0 CCH-362 2.0 50.0
41.0
22.0
22.0 CCH-422 2.5 42.0
22.0
22.0
22.0 7.0
22.0 22.0
7.0
7.0 CCH-442 2.5 82.0
22.0
7.0 22.0
21.0 7.0 7.0 CCH-462 2.5 50.0
22.0
21.0 7.0 7.0 41.0
41.0
21.0 21.0 7.0
41.0 41.0

41.0
7.0 41.0

Toothed channel type

41.0 41.0 41.0
41.0
41.0 41.0
42.0 22.0
22.0
22.0
22.0 22.0 22.0 7.0
7.0
22.0 22.0 7.0 82.0
7.0 7.0 7.0
7.0 7.0
42.0
42.0
41.0
42.0 42.0 82.0
82.0
82.0 82.0
41.0
41.0
41.0 41.0

41.0
41.0
41.0
41.0 41.0

13
13 13 50
50
50 13
0
13 30
50 50 3
30 30 30 For Toothed Channel add “T” after the
Part no. ex: CCH-220T

90
 CCH-240/241
Load table for single beam with uniform (characteristic) Live-
Load
This associated data are considered for perforated and non-perforated c-channel types according to DIN 18.800

Thickness : 1.5 mm
Standard Length : 3.00 m C-Channel: 41x41x1.5
Finishes : Pre-Galvanized, Area of Shear (Az) 1.02 cm2
Hot-Dip Galvanized.
Moment of Inertia (Iy) 3.87 cm4
Z

Moment of Inertia (Iz) 5.68 cm4

Z
min. Section Modulus (Sy) 1.76 cm3
Warping Constant (Iw) 114.17 cm6
Y Y Y Y
Torsional Constant (IT) 0.02 cm4
Plastic Moment cap. (Mpl,y) 0.52 kNm
Z
Self weight (G) 1.44 kg/m

C 41x41x2,5 CCH-240 C
1,67 cm2
5,87 cm4 Z
Chosen Material: 40 B = S 235 JRG2
8,76 cm4
Z
2,72 cm3 Allowable Bending Stress 21,82 kN/cm2
Y Y 6
171,52 cm 41.0 Y Y 17
21.0
0,07 cm4 Allowable Shear Stress 12,60 kN/cm2
0,82 kNm C-Channel:
A) cm2 41.0
Z
2,32 kg/m Modulus ofCross
Elasticity
Section Area (A) 21.000
cm2 kN/cm2
Z
) cm4 41.0
Moment of Inertia (I y ) cm 4

) cm4 Moment of Inertia (I z ) cm4

kg/m Self Weight (G) kg/m
22.0
22.0

Beam Load Data

7.0
7.0
21.0
41.0

41.0 Uniform Load* @

41.0 C-Channel:
Span
cm2
(L) Allowable Load* Deflection Area of Shear (Az) L / 360 cm2
L / 180
4
cm[cm] Moment of Inertia (Iy) cm4
q [kN/m] F [kN] U22.0
[mm] [L /X] q [kN/m] q [kN/m]
cm4 22.0 Moment of Inertia (Iz) cm4
7.0
s (Sy) cm350 6.60 1.70 0.83 610 6.60
min. Section Modulus (S y) cm3 6.60
7.0
) cm6 Warping Constant (Iw) cm6
T) cm460 4.60 1.40 1.19 500 Torsional Constant (IT) 4.60 cm4 4.60
(Mpl,y) kNm 42.0 Plastic Moment cap. (Mpl,y) kNm
70
kg/m 3.30 1.20 1.59 440 Self weight (G) 3.30 kg/m 3.30
82.0
80 2.60 1.00 2.13 380 2.60 2.60
^ S 235 JRG2 41.0 ^ S 235 JRG2
40B = 90 2.00 0.90 2.63 340 Chosen Material: 1.90 40B = 2.00
ress 21,82 kN/cm² Allowable Bending Stress 21,82 kN/cm²
ss 100
12,60 kN/cm² 1.60 0.80 3.20 310 Allowable Shear Stress1.40 12,60 kN/cm² 1.60
21.000 kN/cm² Modulus of Elasticity 21.000 kN/cm²
125 1.00 0.60 4.89
41.0
260 0.70 1.00
150 0.73 0.50 7.40 200 0.40 0.70
13
175 0.53 50 0.50 9.96 180 0.30 0.50
30

200 0.41 0.40 13.14 150 0.20 0.30

225 0.32 0.36 16.42 140 x 0.24
250 0.26 0.33 20.34 120 x 0.18
275 0.22 0.30 25.20 110 x x
300 0.18 0.27 29.20 100 x x

Allowable Load Allowable Uniform Load

F q

Span Span

* Given loads are always “allowable characteristic live load”

91
 Z

CCH-242
Z

Load table for single beam with uniform (characteristic) Live-

Y Y Y Y

Load Z
This associated data are considered for perforated and non-perforated c-channel types according to DIN 18.800
Z

Thickness : 1.5 mm Z

Standard Length : 3.00 m Z

Finishes : Pre-Galvanized,
Y Y 41.0 Y Y
C-Channel: 41x 41x1.5 b2b
21.0
Hot-Dip Galvanized. Area of Shear (Az) 1.43 cm2
Z
41.0
Z Moment of Inertia (Iy) 21.11 cm4
41.0
Moment of Inertia (Iz) 11.37 cm4
22.0 min. Section Modulus (Sy) 5.15 cm3
22.0

7.0
7.0 Warping Constant (Iw) 95.85 cm6
21.0
41.0 Torsional Constant (IT) 0.04 cm4
41.0 Plastic Moment cap. (Mpl,y) 1.53 kNm

C C H - 2 4 2 Self weight (G) 2.88 kg/m

41.0

22.0

C22.0
41x41x2,5 7.0
1,67 cm2 7.0
5,87 cm4
8,76 cm4
Chosen Material:
42.0
2,72 cm3 40 B = S 235 JRG2
171,52 cm6 82.0
0,07 cm4 Allowable Bending Stress 21,82 kN/cm2
0,82 kNm
41.0
C-Channel:
a (A) cm2 2,32 kg/m Allowable Shear Stress
Cross Section Area (A) 12,60cm2 kN/cm2
Iy) cm4 Moment of Inertia (I y ) cm4
Iz ) cm4 Modulus of Elasticity
Moment of Inertia (I z ) 21.000
cm4 kN/cm2
kg/m 41.0 Self Weight (G) kg/m

Beam Load Data

13
50
30

Uniform Load* @
C-Channel:
2
Span
cm (L) Allowable Load* Deflection Area of Shear (Az) L / 360 cm2 L / 180
Iy) cm4 Moment of Inertia (Iy) cm4
Iz) [cm]
cm 4 q [kN/m] F [kN] U [mm] [L /X] Moment of Inertia q
(Iz)[kN/m] cm4q [kN/m]
us (Sy) cm3 min. Section Modulus (Sy) cm3
(Iw) cm50
6 19.20 4.80 0.44 1.130 Warping Constant (Iw19.20
) cm6 19.20
(IT) cm4 Torsional Constant (IT) cm4
p. (Mpl,y)
60 13.30 4.00 0.63 950 13.30
Plastic Moment cap. (M )
13.30
kNm pl,y kNm
kg/m Self weight (G) kg/m 9.80
70 9.80 3.40 0.86 810 9.80
80 7.50 3.00 1.13 710 7.50 7.50
^ S 235 JRG2
40B = Chosen Material: ^ S 235 JRG2
40B =
Stress 90
21,82 kN/cm² 5.90 2.70 1.42 630 5.90
Allowable Bending Stress 21,82 kN/cm² 5.90
ress 12,60 kN/cm² Allowable Shear Stress 12,60 kN/cm²
y 100
21.000 kN/cm² 4.80 2.40 1.76 570 Modulus of Elasticity 4.80 21.000 kN/cm² 4.80
125 3.10 1.90 2.78 450 3.10 3.10
150 2.10 1.60 3.90 380 2.10 2.10
175 1.60 1.40 5.51 320 1.40 1.60
200 1.10 1.10 6.46 310 0.90 1.10
225 0.80 0.90 7.53 300 0.70 0.80
250 0.58 0.70 8.32 300 0.50 0.60
275 0.44 0.60 9.24 300 0.40 0.40
300 0.34 0.50 10.11 300 0.30 0.30

Allowable Load Allowable Uniform Load

F q

Span Span
* Given loads are always “allowable characteristic live load”

92
ANCHORS

www.sfsp-ikk.com
Direction of Loading
The direction of the applied load shall be considered to
determine the most appropriate anchor. The tension and
shear components shall be lesser than the recommended
load/design resistance in the direction concerned.

Fig.1
Tensile Loading
Tensile loads are applied along the axis of fixing (see Fig.2
Fig.1).
Common examples include suspended ceiling
applications and the suspension of mechanical services,
pipe work , duct work ,etc ...

Fig.3
Shear Loads
Shear loads act at right angles to the axis of fixing and
directly against the face of the structural material (see
Fig.2).
Shear performance is governed mainly by the shear
strength of the bolt material and by the compressive
strength of the supporting substrate. Fig.4

Oblique / Combined Loads

Oblique loads are a combination of tension and shear
components (see Fig.3).
If the angle of the applied oblique load is within 10˚ of
pure tension or pure shear, the safe working load for
that direction may be assumed. Otherwise, the applied
oblique load shall be resolved into its shear and tensile
components.

Offset Loads
Offset loads act at right angles to the fixing axis but are
offset from the surface (see Fig.4).
In this situation, the deflection of the bolt due to bending
needs to be considered as well as the shear capacity of
the anchor

Slotted Holes in Fixture

When fixing anchors through slotted holes; it is important
to ensure that there is an adequate surface of contact
between the washer and the fixture to guarantee a
positive clamping force. If in doubt, a square plate
washer with a thickness of 3mm or above would be
recommended in place of the standard washer supplied.

Diamond Drilled Holes

When holes are formed in the structure using a diamond
drilling system; extra care is required to ensure the holes
are thoroughly cleaned by brushing and blowing for at
least three times. Also, to make a key for the anchor
(particularly if a bonded anchor is installed) the sides of
the hole shall be roughened up by inserting a standard
masonry bit into the hole attached to a hammer action
drilling machine. A resin with minimal shrinkage shall be
selected for diamond drilled holes.

94
 Yellow zinc Stainless
EXPANSION STEEL ANCHOR -plated
STM Steel
SteelYellow z
Thread (Zn) Threadplated S(
STM STM/H
Thread
M6 M6 M6
M8 M8 M8

M 10 M 10 M 10
Features: M 12
• Suitable for all screws or threaded bolts with metric thread.
• Low energy impact, power-saving assembly. M 12
• Multiple removing and fixing.
• Inside threaded anchor, allows great flexibility. Order exa
• Can use variable lengths and art of threaded rods or bolts.
• Small edge distance and small distance between anchors.
•P
Order example: STM - Zn - M
 rovide uniform load by tightening the screw or hexagon nut, the cone pulls into the expansion anchor and tightens
against the drilled hole.
• Suitable for use in concrete and natural stone.

Typical Applications:
Cable Management , handrails, brackets, staircases, ladders, machines, window panels, base plates, scaffoldings
and frameworks

Technical Data:
Recommended loads (non cracked -concrete C 20/25).

Tension Load
Yellow zinc
Shear Load
Bending Stainless
Screw Grade
S
plated Steel x
Type

Steel
Moment
(Order No)
(kN) (kN) (Nm)
M6
M8
2.5
3.3
2.3
4.4
Thread (Zn) 3.9
17 Thread
8.8
8.8
M10 4.7 6.5 34 8.8

M6 M6
M12 6.9 8.5 60 8.8
*for cracked concrete we shall use 0,5 x this value (approximately)

Materials:
• Zinc plated steel. M8 M8
• Stainless steel [ SS 304 (A2), SS 316 (A4) ].

Setting Data: M 10 M 10
Edge distance > 1,5 x H eff., distance between anchors > 3 x H eff.
Thickness of foundation > 2 x H eff.
M 12
Edge Distance Thickness of
Tightening Spanner
H eff. Distance Between Foundation Washer
Size Torque size
C Anchors S hmin

M6
(mm)
40
(mm)
60
(mm)
120
(mm)
100
Order example: STMH - Zn - M
(Ø)
12 x 1.6
(Nm)
10
(mm)
10
M8 45 68 135 100 16 x 1.6 20 13
M10 55 83 165 110 20 x 2.0 40 17
M12 70 105 210 140 24 x 2.5 75 19

95
DROP-IN ANCHOR - SDA

SDA

Features:

• Provides permanently fixed threaded socket in concrete.

• Use in non-cracked concrete or cracked concrete and natural stone.
• The anchor will spread and tighten against the drilled hole after
inserting with setting tool.
• Low setting depth, reduced drilling time.
• Enables cost-effective assembly .
• Multiple removing and fixing.

Typical Applications:

Pipes, ventilation ducts, suspended ceilings, sprinkler systems, brackets, threaded rods and Cable Trays.

Technical Data:

Bending
Type Tension Load Shear Load Screw Grade
Moment
(Order No)
(kN) (kN) (Nm)
M6 2.5 2.3 3.9 8.8
M8 3.3 4.4 17 8.8
M10 4.7 6.5 34 8.8
M12 6.9 8.5 60 8.8
*for cracked concrete we shall use 0,5 x this value (approximately)

Materials:

• Zinc plated steel.

• Stainless steel [ SS 304 (A2), SS 316 (A4) ].

Setting Data:

Edge distance > 1.5 x effective anchorage depth, distance between anchors
> 3,0 x effective anchorage depth, min. thickness of foundation > 2,5 x H eff.

Edge Distance Thickness of

Tightening Spanner
H eff. Distance Between Foundation Washer
Size Torque size
C Anchors S hmin
(mm) (mm) (mm) (mm) (Ø) (Nm) (mm)
M6 25 37.5 75 100 4 10 10
M8 30 45 90 100 9 13 13
M10 40 60 120 130 17 17 17
M12 50 75 150 140 30 19 19
M16 65 197.5 195 160 75 24

96
SLEEVE ANCHOR - SAS
Features:

• Suitable for use in concrete, natural stone, brickwork and blockwork

• Small distance between anchors.
• Optimum performance in most base material types. SAS
• No protruding threads after installation.
• Small distance between anchors and from edge.
• Controlled expansion.
• Zinc plated > 5µm.
• Effective force distribution in the drilled hole.
• Sleeve anchor with hexagon screw or with threaded bolt.

Typical Applications:

Uni-channel ,railings, steel constructions , machines, high-racks, cable support systems and mechanical fixations.  

Technical Data: Materials:

Recommended loads (non cracked-concreted C 20/25). • Zinc plated steel.

M H A Sleeve Anchor
Metal Products

• Stainless steel [ SS 304 (A2), SS 316 (A4) ].

Tension Load Shear Load Torque Moment
Bolt Size
(kN) (kN) (Nm) Fea tur es
M6 2.56 2.0 5.0 • Sma ll ed
M8 3.33 3.3 12.5 • Torque co
M10 4.1 5.0 25.5
• Zinc plat
M12 6.66 7.5 .......
*for cracked concrete we shall use 0,5 x this value (approximately)
• Through

Setting Data: Application

Edge distance > 1.5 x effective anchorage depth, distance between anchors
steel constru
> 3,0 x effective anchorage depth, min. thickness of foundation > 2,5 x H eff.

Distance
Edge Thickness of
Between Washer Tightening
Bolt H eff. Distance Foundation Spanner
Anchors (Ø) Torque
Size C hmin size
S
(mm) (mm) (mm) (mm) (mm) (Nm)
M6 35 52.5 105 70 18 x 1.6 8 10
M8 40 60 120 80 16 x 1.6 25 13
M10 50 75 150 100 20 x 2.0 40 17
M12 75 112.5 225 150 26 x 2.0 50 19
Type Tension load Shear load Bending moment Tighten torque Distance between Distance to ed
(Order No) (kN) (kN) (Nm) (Nm) anchor S (mm) C (mm)
Sleeve Anchor - SAS:
M6 2.0 2.5 4.20 8.0 105 55.0
M8 3.0 3.3 5.30 25.0 120 60.0
With hexagon screw (non-cracked
M10 concrete
5.0 C20/25). 5.5 12.80 40.0 150 75.0
M12 7 .5 8.0 25.0 50.0 225 115.0
Hole Ø in Drilling Setting Min.Usable Usable Length Drilling Depth
Length Drill H eff.
Size I nsta lla tion
Fixture Depth Depth Length
(mm) (Ø) (mm) (mm) (Ø) (mm) (mm)
M6 45 8 10 55 35 35 5 Spanner
Size M Drill Ø
M6 60 8 10 55 35 35 15
M8 60 10 12 60 40 40 15
M8 80 10 12 60 40 40 25 Washer H eff Tinst
M10 70 12 14 70 50 50 15 Setting Depth
M10 100 12 14 70 60 50 35
M H A -S Sleeve Anchor with hexagon screw
*for cracked concrete we shall use 0,5 x this value (approximately).
Length

97
THROUGH BOLT (WEDGE ANCHOR) - STB
Features:

• Suitable for use in cracked concrete or in non-cracked concrete and in natural stone.
• Special design of the clip in stainless steel which ensures a safe hold in the hole.
• Torque controlled expansion.
• Zinc plated > 5µm.
• User friendly, face fixing or through fixing.
SDB
Typical Applications:

Uni - channel, hand rails, steel construction, Cable Trays, supports, brackets, ducts and shelf feet.  

Technical Data:

Through Bolt zinc plated (non-cracked C20/25).

Bolt Size
Tension Load Shear Load Throughbolt, stainless steel A4/316
Torque Moment
Usable Length Drilling Depth

M6
(kN)
2.1
(kN)
1.9
Throughbolt, stainless steel A4/316
(Nm)
4.0 Drill Ø
M8 4.0 4.0 15.0
M10 5.9 5.95 30.0
M12 8.8 10.0 50.0
Washer
H eff Fea tu
Setting Depth • Eur
M16 12 16.0 100 Bolt Length
*for cracked concrete we shall use 0,5 x this value (approximately)
• Tor
• App
Materials: • Sta
• Fac
• Zinc plated steel.
• Stainless steel [ SS 304 (A2) , SS 316 (A4) ].
Applic
fa ca de
M H A Sleeve Anchor
Metal Products

under
Fea tu
• Sm
• Tor
Through bolt • Zin
• Th
Setting Data: Bolt Bolt
Size Size Tension
Tension load load Shear load
Shear load
BendingBending
momentmoment
Heff. Heff.Edge Distance
Edge D
(Nm)
(kN) (kN) (kN) (kN) (Nm) (mm) (mm) C (mm)
Appli
C(

Edge distance > 1,5 H eff. , distance betweenM 6 M 6 > 3 x 2.6

anchors H eff.2.6 3.3 3.3 5.5 5.5 40 40 60 steel 6c
Thickness of foundation > 2 x H eff. M8 M8 4.1 4.1 6.3 6.3 13 13 50 50 75 7
M 1 0M 1 0 5.8 5.8 8.5 8.5 26.5 26.5 58 58 87 8
M 1 2M 1 2 9.2 9.2 12 12 46.5 46.5 68 68 102 1
Edge Distance 14 14
M 1 6M 1 6 Thickness of 23 23 118.5 118.5 80 80 120 1
Tightening
Bolt H eff. Distance Between Washer Foundation Spanner
Torque
Size C Anchors S hmin Size
(mm) (mm) (mm) (Ø) (mm) (Nm)
M6 40 60 120 12 x 1.6 100 7 10
I nsta lla tion
M8 50 75 150 I nsta l16laxt1.6
ion 100 14 13
M10 58 87 174 20 x 2.0 120 30 17
M12 68 102 204 24 x 2.5 140 35 19
M16 80 120 Type
240 Tension
30 x 3.0 load 160 Shear load
80 24 moment Tighten torque
Bending Distance between Distan
(Order No) (kN) (kN) (Nm) (Nm) anchor S (mm)

M6 2.0 2.5 4.20 8.0 105

M28 3.0 3.3 5.30 25.0 120
M10 5.0 5.5 12.80 40.0 150
98 M12 2 7 .5 8.0 25.0 50.0 225
 SHIELD ANCHOR - SSA
Features:

• Assembly detachable, multiple removing and fixing. SSA

• Low energy impact, power-saving assembly.
• Force controlled expansion.
• Flexibility inside threaded anchor.
• Variable length and art of threaded rods or bolts.
•By tightening the screw, the cone pulls into the sleeve and tense against the drill hole.
• Small edge distance and small distance between anchor.
• Expansion elements are held together by a spring.
• Optimum taper nut angle for maximum expansion.
• Pressed steel segment ensures consistent dimensional accuracy.
• Provide a projecting stud to support fixture during installation and removal.
• Suitable for use in concrete, natural stone, brick and sand stone.

Typical Applications:

For fixing: steel constructions, handrails, consoles, brackets, ladders, gates and spacing designs.

Technical Data:
(Recommended loads concrete C 20/25 and in brick work).

M H A Sleeve Anchor
Distance to Edge Distance Between Min. Thickness of H eff.
Metal Products

Size C Anchors S Foundation hmin

(mm) (mm) (mm) (mm)
M6 52.5 105 70 35
Fea tu
M8
M10
60
75
120
150
80
100
40
50
t Sm
M12 90 180 120 60 t Tor
t Zin
Materials: t Thr
• Zinc plated and die-cast.
Applic
Setting Data:
steel c
Edge distance > 1,5 x H eff., distance between anchors > 3 x H eff.
Thickness of foundation > 2 x H eff.

Concrete
Brick Work Torque
Torque Brick
Size Tension Shear Tension Shear Concrete

KN KN KN N.m N.m
M6 3.3 2.1 1.6 6.5 5.0
M8 4.8 4.4 2.1 15.0 7.5
M10 6.2 6.1 2.6 27.0 13.0
M12 9.7 12.4 3.9 50.0 23.0
*for cracked concrete we shall use 0,5 x this value (approximately)
Type Tension load Shear load Bending moment Tighten torque Distance between Distan
(Order No) (kN) (kN) (Nm) (Nm) anchor S (mm) C

M6 2.0 2.5 4.20 8.0 105

M8 3.0 3.3 5.30 25.0 120
M10 5.0 5.5 12.80 40.0 150
M12 7 .5 8.0 25.0 50.0 225 1

I nsta lla tion 99

 CHANNEL NUTS
Nut without Spring Nut with Short Spring Nut with Long Spring Hammer Head Bolt

Material: Zinc plated steel and stainless steel 304 (A2),316 (A4).
Tolerance: Metric thread 6 H acc. DIN 13-20.
tt t tt t
20
20 20 Washer Ø 40

M
M M 3

length
0.18

0.18

0.18

0.18
34.5

34.5

t
LL FL
FF34.5
10
10 10 34
34 34

Short Spring Long Spring

Available length: L 30mm, 40mm, 50mm, 60mm.

Material: Zinc plated.

ALLOWABLE LOAD CAPACITIES FOR CHANNEL NUTS

AND BOLTS
Mild Steel Channels, Bolt Material zinc plated or hot dip-galvanized
Pull out Longitudinal Tightening
Thread Size )Force Fv (kN )Force FL (kN )Torque (Nm
M6 5.0 1.0 12.0
M8 6.0 2.4 28.0
M10 7.0 3.5 55.0
M12 7.0 5.0 55.0 Fv
Stainless Steel Channels, Bolt Material Stainless steel A4
Pull out Longitudinal Tightening
Threaded Size )Force Fv (kN )Force FL (kN )Torque (Nm
M6 5.0 0.3 6.5
M8 6.0 0.6 16.0
M10 7.0 1.2 31.5
FL
M12 7.0 1.7 55.0

Note: Do not exceed channel capacity

ALLOWABLE LOAD CAPACITIES FOR TOOTHED CHANNEL NUTS AND

BOLTS Stainless Steel Toothed Channels, Bolt Material Stainless steel A4

Mild Steel Toothed Channels, Bolt Material zinc plated or hot dip-galvanized Longitudinal Tension Load Tightening
Bolt Size )Force FL (kN )(Fv )Torque (Nm
Longitudinal Tension Load Tightening
Bolt Size M6 2.2 5.0 6,5
)Force FL (kN )(Fv )Torque (Nm
M6 2.2 5.0 12 M8 4.0 6.0 16.0

M8 4.0 6.0 28 M10 5.0 7.0 31,5

M10 5.0 7.0 55 M12 5.0 7.0 55.0

M12 5.0 7.0 55

100
LOCATIONS

www.sfsp-ikk.com
LOCATIONS
BAHRAIN
KIGDOM OF SAUDI ARABIA [email protected]
[email protected]
Manama
Jeddah Qassim / Buraidah Tel : +973 17 874 897
Fax: +973 17 789 470
Tel : +966 12 627 8222 Tel : +966 16 382 3946
Fax: +966 12 627 8722 Fax: +966 16 385 2186

Jeddah - Ghurab Showroom Hail KUWAIT

[email protected]
Tel : +966 12 667 2000 Tel : +966 16 543 3931
Fax: +966 12 661 4306 Fax: +966 16 543 3935 Kuwait City
Tel : +965 2 4924 937
Fax: +965 2 4924 938
Mak kah/Taif Skakah / Qurayyat
Tel : +966 12 541 1206 Tel : +966 14 626 3904
Fax: +966 12 532 1675 Fax: +966 14 626 3905 UNITED ARAB EMIRATES
[email protected]
Mad inah Tabuk
Dubai - Al Rashidiyah
Tel : +966 14 842 1095 Tel : +966 14 423 5203 Tel : +971 4 2591 773
Fax: +966 14 842 1090 Fax: +966 14 423 5203 Fax : +971 4 2591 774

Abu Dhabi - Musaffah

Yanbu Hafr el Batin Tel: +971 2 552 3393
Tel : +966 14 390 1499 Tel : +966 13 729 3644 Fax: +971 2 552 5499
Fax: +966 14 322 7101 Fax: +966 13 729 3644

Khamis Mushayt Dammam OMAN

Tel : +966 17 237 5929 Tel : +966 13 859 0097 [email protected]
Fax: +966 17 237 8783 Fax: +966 13 857 8177 Muscat
Tel : +968 24 591 006
Najran Jubail Fax : +968 24 597 006
Tel : +966 17 546 3873 Tel : +966 13 361 4390
Fax : +966 17 546 3873 Fax: +966 13 362 4499
JORDAN
Al Baha Hofuf [email protected]
Tel : +966 17 237 5929 Tel : +966 13 530 1474 Amman
Fax: +966 17 237 8783 Fax: +966 13 530 7144 Tel : +962 6 556 3030
Fax: +962 6 554 7911
Sharorah Aqaba
Tel : +966 17 532 8153 Tel : +962 6 556 3030
Fax: +966 17 532 8153 Fax: +962 6 554 7911

Gizan
Tel : +966 17 321 6660 EGYPT
[email protected]
Fax: +966 17 321 0665
Cairo 6th of October City
Tel : +20 2 3820 6477
Riyadh North Fax: +20 2 3820 6036
Tel : +966 11 415 5465
Fax: +966 11 456 6627
LEBANON
Riyadh South [email protected]
Tel : +966 11 448 0112
Beirut
Fax: +966 11 447 7421 Tel : +961 1 858 277
Fax: +961 1 858 276
Riyadh West
Tel : +966 11 431 6271
Fax: +966 11 431 7642

Riyadh East
Tel : +966 11 448 0112
WWW.UNITECH-IKK.COM
Fax: +966 11 447 7421

102
FACTORIES
SFSP - KSA SFSP / UAE
[email protected] [email protected]

Specialized Factory for Steel Products SIGMA Factory for Steel Products
3rd Industrial City / Jeddah DIC (Dubai Industrial City)
Tel: +966 12 637 4482 Tel : +971 4 818 1919
Fax: +966 12 636 1963

SFSP / Egypt SFSP / Lebanon

[email protected] [email protected]

Specialized Factory for Steel Products Specialized Factory for Steel Products
6th of October City Giza Tanayel, Bekaa
Tel : +20 2 3820 6477 Tel: +961 8 514 290
Fax: +20 2 3820 6036 Fax: +961 8 514 291

ENGINEERING, DESIGN, MARKETING & MULTIMEDIA

Unitech Deutschland GmbH Multi-D s.a.r.l
Germany Lebanon
[email protected] [email protected]

Stuttgart Multi-d Beirut

Tel : +49 711 6868 7222 Tel : +961 1 841 155
Fax: +49 711 6868 7223 Fax: +961 1 841 156
PP-CT-SMFS17-M19
 SFSP makes every effort to maintain the accuracy and
quality of the information provided in this Catalogue.

However, SFSP cannot guarantee and assumes legal

liability or responsibility for the accuracy or completeness
of the information provided.

Whilst every care has been exercised in the

preparation of this catalogue to ensure that any advice,
recommendations or information is accurate, no liability
or responsibility of any kind is accepted.

Project working details should be entrusted to

appropriately qualified and experienced persons, case by
case.

With a policy of continuous product development, SFSP

may modify product design and specification without
due notice.

In case of any questions or remarks, feel free to contact

the R&D Department.

DISTRIBUTED BY:

www.sfsp-ikk.com

PP-CT-SMFS07-M18

106