JC6000 MULTI AXIS

JOYSTICK CONTROLLER

Innovation In Motion

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
INNOVATION IN MOTION
The JC6000 rugged joystick controller is designed for demanding operator
control applications in off-highway vehicles and other man-machine interfaces,
where strength, reliability, and handle functionality are important. Available in
one or two axis configurations, this joystick can be supplied with non-contact
Hall effect sensors or long life potentiometer tracks. The JC6000’s compact size,
high lever strength and superb proportional control are ideal for applications
which include operator controls on a wide range of off-highway vehicles,
including cranes, loaders, excavators, access platforms, tractors and harvesters.

Handles and grips

The JC6000 can be specified with a choice of handles and grips to increase the
functionality of the operator controls. With a choice of push buttons, trigger grips,
proportional and switched rockers in a variety of different configurations, users
can match their handle selection to suit their unique application.

Innovative design
With a choice of Hall effect sensors or potentiometer tracks to provide
the analogue signals proportional to lever movement, the JC6000
can be configured to provide a range of output signals, directional
and center switching functions, lever forces, and handle styles. CAN
output can also be specified on the Hall sensor version for digital
communication with vehicle systems.•

Features Benefits
• Hall effect or potentiometric sensing • Long life and maintenance-free operation
• Single or dual axis control • Suited to a range of operator control functions
• High strength lever with superb proportional control • Rugged and smooth lever movement
• Sealed above the panel to IP66 •Operation in hostile environments
• Choice of outputs and switches • Enables user configuration for system safety
• Choice of handles/grips with or without switches • Additional operator control functions
• AMP 040 series multi-lock connectors • Simple installation
• Interchangeable with Penny + Giles' JC600 model • Improved performance within the same footprint

Quality Assurance
Penny + Giles are accredited to BS EN ISO9001:2000
Quality is at the heart of all our systems ensuring the
reliability of our products from initial design to final
despatch.
Certificate No.LRQ 0924881

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
J C 6 0 0 0 M U LT I -A X I S
JOYSTICK CONTROLLER
Total reliability
The JC6000 includes lever mechanics designed to give smooth proportional
control, with Hall effect sensors that provide contactless, long life operation up to
15 million operations. Alternative potentiometer tracks featuring multi-fingered
precious metal wipers give low electrical noise and a long life of greater than 5
million operations.

Safety
The JC6000 with the Hall sensors option has dual outputs
fitted as standard, allowing the signals to be monitored and
compared for failure detection in safety critical applications.
Additional independent switch functions can be specified for
directional and center position indication - vital for vehicle system
start-up safety. These switch functions are also available with the
potentiometer tracks, which can also be specified with padding
resistors to limit the output signals to 10-90% or 25-75%, allowing
comparison and error detection.

Custom design
Penny+Giles offer an extensive range of fingertip and hand
operated joysticks in standard modular configurations,
designed to meet the majority of individual customer needs, but
we can customise our designs for OEMs who require something
more specialised to their application. Please talk to our technical
sales team about your requirements.

Cell manufactured
The modular design of the JC6000 joystick is designed to provide the user
with a wide choice of options, but allows efficient build and despatch using
cell manufacturing principles. Contact your nearest sales office for the latest
information on availability.

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
J C 6 0 0 0 JOYSTICK CONTROLLER
PERFORMANCE
MECHANICAL
Lever operating force
breakout* N 7 or 16
operating* N 19 or 39 (full deflection)
maximum allowable** N 390 (490 overload)
Lever mechanical angle
single axis only º ±20 forward/reverse
square gate º ±20 in X and Y directions
Seat preferred bias on axis
Expected life 15 million operations (5 million for potentiometer track version)
Weight g 750 without handle fitted
* Measured at 55mm above upper flange face ** Measured 130mm above upper flange face

ENVIRONMENTAL
Operating temperature ºC -25 to +80 (-25 to +80 with microswitches)
Storage temperature ºC -25 to +85 (-25 to +85 with microswitches)
Environmental protection IP66 IEC 60529 (fitted with HKN handle)
(above the flange)
Vibration Level±3g,10Hz to 200Hz (random) @ 3.6g(rms)
Shock 20g, 6mS, half sine profile
EMC immunity level 100V/m, 30MHz to 1GHz, 1KHz 80% sine wave modulation, EN50082-2 (1995)
EMC emissions level Complies with EN50081-2 (1993), 150kHz to 30MHz, level B
ESD immunity level IEC61000-4-2 level 4 8kV contact discharge, 15kV air discharge

ELECTRICAL -
HALL EFFECT SENSOR
Resolution Infinite
Supply voltage range Vdc 5 ±0.5 regulated transient free
Over voltage (maximum) Vdc 15 continuous
Reverse polarity (maximum) Vdc 14.5
Output voltage span - options Vdc ±25% span - nominal 1.1 to 3.9
±30% span - nominal 1.0 to 4.0
±40% span - nominal 0.5 to 4.5
Load impedance (minimum) kΩ 5
Center voltage (no load) % 48 - 52 of supply voltage
Current consumption mA 13 per axis (6.5 per sensor)
Insulation resistance Greater than 50MΩ at 50Vdc
Output sense The dual outputs rise together in the same direction, increasing with lever forward (and right),
decreasing with lever backward (and left)
Output matching See maximum output difference diagram below

ELECTRICAL All Hall sensor connections terminate in a 12-way AMP 040 series multi-lock connector in the
CONNECTIONS joystick base. See page 8 for pin identities
Mating 12 way connector and pins SA48061 (AMP 040 12 way connector 174045-2; pins 175062-1)
Mating 12 way harness P49779 (connector, pins and 380mm long cable)

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
ELECTRICAL -
POTENTIOMETER TRACK
Resolution Virtually infinite
Track resistance ±20% kΩ 1.8, 2, 2.9, 5
Track operating angle º ±18
Output voltage range % 0-100, 10-90, 25-75 of input
Center tap voltage % 48 - 52 of applied voltage
Center tap angle º ±2.5
Center tap to switch alignment º Within 0.5
Supply voltage maximum Vdc 32
Wiper circuit impedance MΩ 1 minimum recommended*
Power dissipation @ 25°C W 0.25
Insulation resistance Greater than 15MΩ at 50Vdc
* The long life resistive elements require a high impedance load in the wiper circuit to minimise
the current flowing through the wiper for optimum life conditions

ELECTRICAL -
DIRECTIONAL OR CENTER
SWITCH (LOW CURRENT) Not available with CANbus output
Switch operating angle º 1.5 or 5 either side of center
Supply voltage maximum Vdc 35
Load current maximum mA 200 resistive

ELECTRICAL All primary potentiometer track and directional/center switch connections terminate in a 16-way
CONNECTIONS AMP 040 series multi-lock connector in the joystick base. Secondary potentiometer track
connections terminate in an 8-way AMP 040 series multi-lock connector. See page 8 for
pin identities
Mating 16 way connector and pins SA47931 (AMP 040 16 way connector 174046-2; Pins 175062-1)
Mating 16 way harness P49780 (connector, pins and 380mm long cable)
Mating 8 way connector and pins SA304522 (AMP 040 8 way connector 174044-2; pins 175062-1)
Mating 8 way harness P303083 (connector, pins and 380mm long cable)

ELECTRICAL -
MICROSWITCH Not available with CANbus output
Switch configuration Two switches per axis. Normally open at lever center position
Switch operating angle º 2 to 5 either side of center
Contact rating 3A @125Vac, 2A @ 30Vdc
Switch life minimum 100,000 cycles, cycled at 1Hz, 1A and 12Vdc
Operating temperature ºC -25 to +85

ELECTRICAL Microswitch connections in the potentiometer joystick will replace the low current
directional/center switches in the 16-way AMP 040 series multi-lock connector in the joystick
CONNECTIONS base. In the Hall sensor joystick, switches terminate in the 8-way connector. See Electrical
Connections on page 8 for pin identities

CAN OUTPUT VERSION JC6000 with Hall sensing option can also be supplied with an integrated CANBUS output
offering the J1939 protocol. This CANBUS interface meets the requirements of IEC61508 SIL
level 1
Supply voltage range Vdc 9 to 36
CAN version CAN 2.0b
Protocol J1939
Under-panel sealing IP66 IEC60529

ELECTRICAL
CONNECTIONS All connections terminate in the 6-way Deutsch DTM04-6P integrated connector
Mating connector and pins P304844 (includes 390mm flying leads)

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
JC6000 JOYSTICK CONTROLLER
H O W TO S P E C I F Y
PERFORMANCE OPTIONS CODE
AXES Single NY
Dual XY

SENSING Potentiometer Px or Pxx selected from below P

Output 5k 0-100%, ±5º directional switch E
1.8k 0-100%, ±5º directional switch N
2.9k 25-75%, ±1.5º directional switch Q
2k 10-90%, ±1.5º directional switch R
2k 10-90%, ±5º directional switch S
2.9k 25-75%, ±5º directional switch T
Dual outputs per axis, 2k 10-90%, ±1.5º directional switch U

Dual Hall Effect sensors each axis Hxx with output selected from below H
Dual Hall Effect sensors each axis and ±1.5º directional switch Bxx with output B
Output selected from below
1.1Vdc to 3.9Vdc K
1.0Vdc to 4.0Vdc L
0.5Vdc to 4.5Vdc M

CANbus Output HC
Single Axis/Dual Axis 1 or 2
Note: Directional track switches not currently available with CANbus output.

LEVER SPRING FORCE Heavy duty, 16N breakout, 39N full deflection H
Medium duty, 7N breakout,19N full deflection M

GATE Square ±20º mechanical angle in X and Y directions S

MECHANICAL No lock or detents fitted NL

FEATURES

MICROSWITCH No switch fitted N

High current microswitches, 2A @ 30Vdc (Not available with CANbus output) Y

INTERFACE Standard interface (no electronics) STN

CANbus output, SAE J1939 protocol, Source Address 33 (HEX) JR1
1000 CAN counts Source Address 34 JL1
Source Address 35 JC1
Source Address 36 JA1

HANDLE/GRIP STYLE Standard knob, no functions HKN

See pages 9-15 Hand grip with options for buttons or rocker HB
Ergonomic grip with multiple buttons and proportional rockers A
Trigger grip with optional rocker switching MG
No handle NH
No handle, flying leads fitted (allows customer to fit own handle.) NHF

E X A M P L E O R D E R C O D E JC6000 - XY- PRR - H - S - NL - N - STN - HKN

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
J C 6 0 0 0 JOYSTICK CONTROLLER

DIMENSIONS POTENTIOMETER AND HALL EFFECT CAN OUTPUT CONTROLLER

Note: drawings not to scale CONTROLLER

61 mounting 61 mounting
screw centers screw centers
M6 Torx T30 supplied M6 Torx T30 supplied

INSTALLATION (4 places)
ø11.93/12.00
(4 places)
ø11.93/12.00
ø9.518/9.548 ø9.518/9.548
The joystick is designed to be fitted from

9.7

9.7
below the mounting panel, through a

32

32
70mm diameter hole. The effectiveness of ø 3.218/3.2 ø 3.218/3.2

the joystick flange sealing is dependent on

the panel mounting surface being

150 (nominal)
Joystick mounting
sufficiently rigid to compress the sealing surface

gaiter. The surface finish of the mounting

panel is critical to achieving an adequate
seal and rough surface finishes, paint

68 (max)

74 (max)
chips, deep scratches, etc. should be
avoided.
16-way connector
Potentiometer interface
Recommended panel thickness (Handle on Hall version)
Forward 80 (includes gaiter)
3.5 to 6mm orientation Pin 1
ident
Pin 9
Pin 1
Pin 1
Recommended screw torque Pin 1
Forward
Fixing screws can be driven to a maximum Pin 5 Pin 7 orientation
ident on this
face
torque of 5Nm when clamped against a
3.5mm thick panel.
8-way connector 12-way connector
secondary pot interface Hall sensor interface
(Switch connections on (handle on potentiometer
The mounting hole depth is 12.6mm. For Hall version). version)).

through-hole installation, the screws can

be driven at a torque of 3.5Nm directly
through the blind cast holes to remove the
CAN OUTPUT OPTIONS
cast covers. The joystick mounting flange
The sealing of the lower cover meets the
should be connected to the vehicle chassis
requirements of IP66 (IEC 60529) and uses
or reference plane (normally zero volts).
an integrated Deutsch DTM04-6P 6 pin
connector with the cover. The use of a
suitable sealed mating connector will
enable a full IP66 connection to be made.
The cover also includes an integrated
breather system to ensure pressure
regulation under all barometric pressure
and temperature conditions without
moisture ingress into the joystick.

See next page for electrical connections

7
Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29
www.wimesure.fr • [email protected]
 J C 6 0 0 0 JOYSTICK CONTROLLER
ELECTRICAL CONNECTIONS
Pin number Potentiometer tracks Hall effect sensors
16-way primary connector 1 Y switch track N/O (lever forward +Y) Pins 1 to 12 used for handle connections
2 X switch track center on See chosen handle style for details
3 X pot track left -
4 X pot track wiper signal -
5 X pot track right -
6 X pot track center tap -
7 X switch track common -
8 X switch track N/O (lever left -X) -
9 Y pot track backward -
10 Y pot track wiper signal -
11 Y pot track forward -
12 Y pot track center tap -
13 Y switch track common Not connected
14 Y switch track N/O (lever backward -Y) Not connected
15 X switch track N/O (lever right +X) Not connected
16 Y switch track center on Not connected

8-way secondary connector (where fitted) 1 Secondary Y pot track backward Forward (directional or micro)
switch common
2 Secondary Y pot track center tap Forward switch output
3 Secondary Y pot track wiper signal Backward switch output
4 Secondary Y pot track forward Backward switch common
5 Secondary X pot track right Left switch common
6 Secondary X pot track wiper signal Left switch output
7 Secondary X pot track center tap Right switch output
8 Secondary X pot track left Right switch common

12-way connector 1 Pins 1 to 12 used for handle connections +5V supply - sensors 3 and 4
2 See chosen handle style for connection details 0V supply - sensors 3 and 4
3 - +5V supply - sensors 1 and 2
4 - 0V supply - sensors 1 and 2
5 - Forward/backward output - sensor 3
6 - Left/right output - sensor 2
7 - Left/right output - sensor 4
8 - Forward/backward output - sensor 1
9 - Not connected
10 - Not connected
11 - Not connected
12 - Not connected

6 pin Deutsch connector CAN output 1 Not available Ground

2 Not available Power
3 Not available CAN high
4 Not available CAN low
5 Not available CAN shield
6 Not available Not connected

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
J C 6 0 0 0 JOYSTICK CONTROLLER
HANDLE OPTIONS
HKN NH or NHF
The HKN handle is the simplest option These options are selected when
available for the JC6000. This handle does no handle is required to be fitted.
not include any additional functionality, but is NHF option has wires fitted to the
designed to allow the joystick to be controlled joystick connector on the base,
by the operator gripping the handle palm through the operating lever.
downwards.

HB
Developed to replicate the functionality of the
traditional mechanical handle, the HB range of
hand grips can be specified with either a button
or rocker switch, mounted into the top of the
handle, within easy reach of the operator’s
thumb. These can be configured as a ‘Person
Present’ feature or, for example, the steer
signal for an access platform.

A RANGE
Designed to meet the demands for more complex control systems in off-highway
applications, the 'A' range of ergonomic hand grips can be fitted with a combination
of analogue outputs, push button and ‘Person Present’ switches. The handle can be
specified with two independent analogue outputs generated by proportional rockers
which, in turn, provide auxiliary directional switching in addition to the potentiometric
output. When coupled with the two axis JC6000 base joystick this unit can provide a
four-axis controller.
This handle can also be purchased separately, for fitting to customer levers or
assemblies. Ask our sales team for more details on this option.

MG
Designed to provide a simple approach to a ‘Person Present’ handle whilst offering the
flexibility of switch options in the top of the handle. The profile of the MG handle
ensures the operator's fingers are permanently close to the buttons, minimising operator
fatigue and maximising functional control. The handle can be supplied with or without
a hand rest and can be configured with a combination of trigger lever, single or dual
switches.
This handle can also be purchased separately, for fitting to customer levers or
assemblies. Ask our sales team for more details on this option.

9
Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29
www.wimesure.fr • [email protected]
 HKN HANDLE OPTION
DIMENSIONS
ø35

45
110 max

NH OR NHF HANDLE OPTIONS

ELECTRICAL NH option has no wires fitted.
CONNECTIONS
Wire size 28AWG NHF option allows customer to
Wire current 1.4A fit own handle style to joystick
operating lever.
250 min

Pin Wire color

see page 7 for lever dimensions
1 Grey
2 Yellow
3 Red
4 Orange
5 Brown
6 Black
7 Green
8 White
9 Blue
10 Violet
11 Pink
12 Red/Yellow
13 Not connected
14 Not connected
15 Not connected
16 Not connected

NHF handle option note: Wires terminate on the 12-way connector (Potentiometer
version), or the 16-way connector (Hall sensor version).

10

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
HB HANDLE OPTIONS
DIMENSIONS HB0 HB1 HB2 HBD

ø35

155

155

164
115
149 max

SPECIFICATION HBO HB1 HB2 HBD

Maximum height above flange mm 149 155 155 164
Maximum grip diameter mm 35 35 35 35
Environmental sealing (IEC 60529) IP65 IP65 IP65 IP65

Number of switches 0 1 2 1
Action Momentary rocker Momentary rocker Momentary button
Switch operating force N - - - 7
Maximum current @ 30Vdc A - 2.5 2.5 5
Expected life (operations) 100,000 100,000 100,000 100,000

ELECTRICAL
CONNECTIONS
Common terminal 11 11 11
N/O contact switch 1 4 4 1
N/C contact switch 1 1
N/O contact switch 2 1

Note: Signals terminate on the 12 way connector (potentiometer version) or the 16 way connector (Hall sensor version)

11

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
 A RANGE HANDLE OPTIONS
SPECIFICATION ROCKER
Maximum height above flange mm 166 Rocker profile Standard (S) or V profile (V)
Maximum grip diameter mm 61 Breakout force N 5 at the end of the rocker
Environmental sealing Operating force N 15 at the end of the rocker
(IEC 60529) IP65 Mechanical movement º ±10 (±1°)
Number of switches 1 to 6 in the top plate Electrical movement º ±9 (±1°)
Action Momentary button Expected life (operations) 5 million
Switch operating force N 3 Load current (maximum) mA 200 (see note on page 5)
Maximum current @ 50Vdc mA 200 Power dissipation @ 25ºC W 0.25
Expected life (operations) 1 million Track resistance Will match JC6000 Y axis resistance †

Weight g 170 - A2LD option Output voltage Will match JC6000 Y axis output †

Operating temperature ºC -40 to +70 Center tap angle º ±1.5

Storage temperature ºC -40 to +80 Directional or center off switch Standard
Switch gap º 2.5 either side of center
Switch supply voltage Vdc 35
† unless requested otherwise

FUNCTIONALITY SWITCHES ROCKERS

1 2 3 4 5 6 TOP Person Present LEFT RIGHT HORIZONTAL
SWITCH 1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
SWITCH 2 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
SWITCH 3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
SWITCH 4 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
SWITCH 5 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
SWITCH 6 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
TOP SWITCH ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
PERSON PRESENT ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

LEFT ROCKER ✔ ✔ ✔ ✔ ✔ ✔
RIGHT ROCKER ✔ ✔ ✔ ✔ ✔ ✔
HORIZONTAL ✔ ✔ ✔

SWITCH AND ROCKER OPTIONS

A000 A400 3 2 A1LO A1RO A0H0

A00T A40T A1LT A1RT A0HD
A00D A40D A1LD 1 A1RD 3
A00B A40B A1LB A1RB
4 1

A100 A500 3 2 A2LO 2 A2RO 3 A1HO 2

A10T A50T A2LT A2RT A1HD
A10D A50D 5 A2LD A2RD
A10B A50B A2LB A2RB
1 1 4
4 1

A200 A600 3 2 A3LO 2 A3RO 3 A2H0 3 2

A20T A60T A3LT A3RT A2HD
A20D A60D 5 6 A3RD 5
A3LD
A20B 3 2 A60B A3LB A3RB
4 1
1 4
6

A300 3 2 AOLO AORO AOBO

A30T
AOLT AORT A0BD
A30D
AOLD AORD
A30B
1 AOLB AORB

12

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
DIMENSIONS
110 60

Push button
switch

Left
rocker

132
Top switch

ø55

166
Person present switch

Standard rocker profile

Optioinal V - rocker profile

ELECTRICAL
CONNECTIONS
Pin Wire color Pin Wire color
Common terminal (for all switches) 11 Black Rocker center tap 6 Yellow/Red*
Switch 1 4 Blue Rocker zero or negative supply (L, R or H) 10 Pink/Grey
Switch 2 3 Yellow Rocker output signal (L or H only) 5 Pink
Switch 3 2 Blue/White Rocker output signal (R) 9 White
Switch 4 1 White/Green Rocker switch common 11 Black
Switch 5 † Red Rocker switch (L forward) 2 Blue/Orange
Switch 6 † Violet Rocker switch (L backward) 1 Green
Top switch † Pink with marker Rocker switch (R forward) 3 Yellow
Person present switch 12 Red/Green Rocker switch (R backward) 4 Blue
Person present switch 8 Black/White Rocker switch (H left) 4 Blue/Orange
Rocker positive supply (L, R or H) 7 White/Red Rocker switch (H right) 1 Green

† depends on other options selected

*Center tap not connected on A3LB and A3RB handles

Note: Signals terminate on the 12-way connector (Potentiometer version), or the 16-way
connector (Hall sensor version)

ORDERING CODES A -2 - L - D -R - S
Push button Rocker profile
select 1 to 6 in the top plate S = Standard
V = V profile
Rocker position
O = None Rocker resistance code
L = Left (See page 6 for codes)
R = Right
B = Both Additional switches
H = Horizontal O = None
T = Top
D = Person Present (Deadmans)
B = Both

Note: When ordering a handle fitted with a rocker, two profiles can be supplied
(S = standard profile; V = v profile) please specify style when ordering.

13

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
 MG HANDLE OPTIONS
DIMENSIONS
Switch 1

ø62.5

ø40

28
Switch 2
54

14

Switch 1/2

114
Trigger

168

SPECIFICATION
Maximum height above flange mm 168
Maximum grip diameter mm 40
Environmental sealing (IEC 60529) IP67 (IP66 with trigger switch)
Number of switches 0 to 3
Action Momentary Button, Rocker or Trigger
Switch operating force
Trigger N 5
Switch 1 or 2 N 7
Maximum current @ 30Vdc mA 100
Expected life (operations) 1 million
Operating temperature ºC -25 to +75
Storage temperature ºC -30 to +80

14

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]
HANDLE CODE Top switch position Trigger switch Hand rest
MG00 None No No
MG01 1 No No
MG02 1&2 No No
MG03 1&2 Yes No
MG04 1&2 Yes Yes
MG05 1 Yes Yes
MG06 1&2 No Yes
MG07 1 No Yes
MG08 1 Yes No
MG09 None Yes Yes
MG10 None None Yes
MG11 None Yes No
See Electrical Connections for wire color codes.

ELECTRICAL Pin number Wire color

CONNECTIONS
Common terminal (for top switches) 12 Black
Switch 1- Left 6 Blue
Switch 2 - Right 3 Green
Trigger switch 4 Blue/Orange
Trigger switch 5 Yellow
Note: Signals terminate on the 12-way connector (Potentiometer version), or the 16-way
connector (Hall sensor version)

15

Wimesure • 54, rue de Versailles • 78460 CHEVREUSE • Tél. 01 30 47 22 00 • Fax 01 30 47 28 29

www.wimesure.fr • [email protected]