Missouri University of Science and Technology

Scholars' Mine
International Conferences on Recent Advances in 2010 - Fifth International Conference on Recent
Geotechnical Earthquake Engineering and Soil Advances in Geotechnical Earthquake Engineering
Dynamics and Soil Dynamics

May 24th - May 29th

Ground Improvement Using Stone Column

K. S. Beena
Cochin University of Science and Technology, India

Follow this and additional works at: http://scholarsmine.mst.edu/icrageesd

Part of the Geotechnical Engineering Commons

Recommended Citation
Beena, K. S., "Ground Improvement Using Stone Column" (2010). International Conferences on Recent Advances in Geotechnical
Earthquake Engineering and Soil Dynamics. 7.
http://scholarsmine.mst.edu/icrageesd/05icrageesd/session08/7

This Article - Conference proceedings is brought to you for free and open access by Scholars' Mine. It has been accepted for inclusion in International
Conferences on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics by an authorized administrator of Scholars' Mine. This
work is protected by U. S. Copyright Law. Unauthorized use including reproduction for redistribution requires the permission of the copyright holder.
For more information, please contact [email protected].
 GROUND IMPROVEMENT USING STONE COLUMN

BEENA K. S.
Professor in Civil Engineering, School of Engineering, Cochin University of Science and Technology
Cochin, Kerala, INDIA 682 022

ABSTRACT

The use of stone column (called granular piles) has proved to be an economical and technically viable ground improvement technique
for construction on soft soils and has been successfully applied for the foundation structure like oil storage tanks, earth embankments,
raft foundation etc. When the stone columns are installed in extremely soft soils, the lateral confinement offered by the surrounding
soil may not be adequate to form the stone column. In such soil, encasing the stone column with a geotextile can induce required
lateral confinement. Considering the cost aspect of stone columns, the major portion of the cost owes to the cost of stone. If replacing
a portion of stone by some other cheaper material, without affecting the performance, can reduce the total cost In the present work
experimental studies are carried out to evaluate the behavior of stone column encased with geotextile, in which stone is replaced by
cheaper quarry dust The effect of geotextile is also studied. It is revealed from the studies that a portion of stone can be replaced by
cheaper quarry dust without with out affecting the performance of the column.

INTRODUCTION

In quest of knowledge and demand, there is ever increasing While most of these technologies were originally developed
awareness of new technologies created or found by man. The for uses other than seismic risk mitigation, many of the recent
field of geotechnical engineering is not new to this advances in the areas of deep densification, jet and
phenomenon. Over the last century, the field of geotechnical compaction grouting, and deep mixing methods have been
engineering has achieved many milestones with brilliant ideas spurred on by the need for practical and cost effective means
and advancements. The ground improvement techniques are for mitigating seismic risks. Many of these methods have also
one of the areas, which have attained lots of interest, and been applied to increase the liquefaction resistance of loose,
improvements due to an interesting fact that anything can be saturated, cohesion less soils. Ground improvement techniques
constructed anywhere- if only proper foundation is laid. basically utilize the effects of increasing adhesion between
soil particles, densification and reinforcement to attain one or
Many methods for ground modification and improvement are more of the following:
available around the world now, including dewatering, • Increased strength to improve stability,
compaction, preloading with and without vertical drains, • Reduced deformation due to distortion or compressibility of
grouting, deep mixing, deep densification and soil the soil mass,
reinforcement are among those. Many of these techniques, • Reduced susceptibility to liquefaction, and
such as dewatering, compaction, preloading and grouting, • Reduced natural variability of soils.
have been used for many years. However, there have been
rapid advances in the areas of deep densification (vibro- Of many techniques of ground improvements, stone column
compaction, deep dynamic compaction, compaction piles, and has gained lots of popularity since it has been properly
explosive densification), jet and compaction grouting, deep documented in the middle of the last century. Potential
mixing, and vibro-replacement and vibro-displacement in applications of stone column include stabilizing foundation
recent years. These methods have become practical and soils, supporting structures, landslide stabilization, and
economical alternatives for many ground improvement reducing liquefaction potential of fine sands.
applications.

Paper No. 8.11 1

Considering the cost aspect of stone column, the major portion stone column, the major portion of the cost owes to the cost of
owes to the cost of stone. If some other cheaper material, can stone. If this can be reduced by replacing other cheaper
replace the stones, without affecting the performance, the cost materials, without affecting the performance, the total cost can
of construction can be reduced. Here an attempt is made to be reduced. The effect of a natural geotextile as an encasing
replace the stone partly with quarry dust and the performance material is also studied.
is studied in terms of load settlement behavior. The effect of
geotextile encasement is also studied using a natural geotextle.
MATERIAL CHARACTERIZATIONS

LITERATURE REVIEW The clay used is natural clay which is locally available at a
place called Maradu in Kochi. Collected sample has been air
Hughes and Withers (1974) carried out series of model dried and pulverized. The pulverized sample was sieved
tests in normally consolidated clay. The test results through 4.75 mm sieve for easy mixing and quicker hydration.
indicated that ultimate capacity of stone column was governed The properties of soil are obtained in the geotechnical
primarily by the maximum radial reaction of the soil against engineering laboratory as per IS specification. Properties of
the bulging and the extend of vertical movement in the stone clay, quarry dust and stone aggregate and geotextiles are
column was limited to about four times the diameter. Shankar tabulated in Tables 1 to 3 respectively.
and Shroff (1997) conducted experimental studies to study the
effect of pattern of installation of stone columns and Table 1. Properties of Soil (air dried sample)
showed that triangular pattern seems to be optimum and
rational. Mitra and Chatopadhyay (1999) studied the Property Value
effect of different factors influencing the capacity of stone
column improved ground from the available literature and Specific gravity 2.74
showed that in the case of columns failing by bulging the Liquid limit (%) 59
critical length is about three to five times the stone column
diameter. Mitchell and Huber (1985) compared the field Plastic limit (%) 27
performance of stone columns with the predictions by finite Plasticity index (%) 32
element analysis and reported that the agreement was
generally good. It was concluded further that Clay content (%) 12
settlement predictions using other simpler methods also gave
Silt content (%) 61
values, which agreed reasonably with the measured values.
However, when used in sensitive clays, stone columns Max. dry density(KN/m³) 15
have certain limitations. There is increase in the settlement of
the bed because of the absence of the lateral restraint. The OMC (%) 30
clay particles get clogged around the stone column
thereby reducing radial drainage. To overcome these
limitations, and to improve the efficiency of the stone columns Table 2. Properties of Quarry Dust and Stone
with respect to the strength and the compressibility, stone
columns are encased (reinforced) using geogrids/
geocomposites. Deshpande & Vyas (1996) have brought out Property Quarry Stone
conceptual performance of stone columns encased in Dust
geosynthetic material. Effective size (mm) 0.041 4.6
Uniformity 3.85 1.4
Malarvizhi and llamparuthi (2002) has studied load versus
settlement response of the stone column and reinforced stone coefficient
column i.e., geogrid-encased stone column in the laboratory.
Coefficient of 5.6 0.93
Load test were performed on soft clay bed stabilized with
single stone column and reinforced stone column having curvature
various slenderness ratio and using different type of encasing
Density(KN/m³) 19.5 17.6
material. The settlement in reinforced stone column is lesser
o
than the stone column and the settlement decreased with the Angle of internal 37 -
increasing stiffness of the encasing material.
friction

In recent years stone column have been increasingly used for Cohesion (kg/cm²) 0.15 -
improvement of soft soils to increase the load bearing and to
reduce the settlement. This present experimental work
examines the behavior of stone column, in which stone chips
are replaced by quarry dust. Considering the cost aspect of

Paper No. 8.11 2

 Table 3 Properties of Coir Geotextile*
Experimental Setup for the Load Test
TYPE Non woven lined(NWL)
Tests were conducted on a single column of diameter 110 mm
for various proportions of the stone column and quarry dust on
Mass / Area (g) 1350 a standard loading frame as a strain-controlled test. Fig 1
Thickness at 2 kPa (mm) 11.35 shows the schematic sketch of test set up.

Wide tensile strength 3.49

(kN/m) machine direction

* After Rao and Balan(2000)

EXPERIMENTAL INVESTIGATIONS

Preparation of Clay bed

The air-dried and pulverized clay sample was mixed with

required quantity of water to achieve a consistency
index of 0.1. Water content of 56% was used. Initially the soil
was thoroughly mixed with the water and kept covered for
48 hours in order to achieve uniform consistency. After
48 hours of hydration, the soil was mixed and kneaded well
and checked for moisture content. Loss of water, if any due to
evaporation was compensated by adding water before forming
the bed. Thoroughly mixed clay is filled in the tank in layers
of 100 mm thick and the weight of clay was adjusted so as to
achieve a uniform wet density of 17 kN/m³. Care was taken
Fig 1 Schematic Sketch of Test Set Up
to avoid the entrapped air by tapping the clay layers
gently with a wooden plank.
Load test were carried out on single columns of 110 mm
diameter. Loading was done on a plate of 243 mm
diameter, which was 2.2 times the diameter of the single
Stone Column Installation
column, placed over the clay filled in the tank of size 500
mm diameter and 500mm in height. Loading was done over
The center of the cylindrical tank was properly
clay alone, clay stabilized by stone column and clay stabilized
marked and a PVC pipe of the required diameter was placed at
with stone column encased within geotextile of the same
the center of the tank. Around this pipe, clay bed was formed.
diameter as that of the stone columns alone. The load was
The clay layer was tamped with a wooden tamper frequently
applied through a proving ring at a maintained rate of 1.2
and gently to expel air during the process of filling. The stone
mm/min and the settlement of the plate was recorded by
required to form the column was carefully charged in the tube
means of two dial gauges set diametrically opposite.
in three layers. Each layer was compacted using 12mm
diameter rod to achieve a density of 17 kN/m 3.

For reinforced stone columns the reinforcement was stitched

and placed around the PVC tube. After preparing the clay
bed, the tubes were charged with stone chips and
compacted in layers. The PVC tube was withdrawn to certain
level and charging of stones for the next layer was continued.
The operations of charging of stones, compaction and
withdrawal of tubes were carried out simultaneously.

Further the bed thus prepared was left for 24 hours to

obtain uniform bed, which also ensured proper contact
between clay and reinforced stone column. The test after 24
hours of preparation of the bed has also ensured gain in their
strength of disturbed clay. Fig 2 Photograph of the Test Set-up

Paper No. 8.11 3

RESULTS AND DISCUSSION geotextile. Pressure settlement response of clay bed with stone
column encased with geotextile is shown in Fig. 4.

Effect of stone column without geotextile

Pressure settlement response of clay bed and stone column 35 Clay alone
without geotextile are shown in Fig.3.

30 Clay with
35
Clay alone stone
column S1
25 stone
30 Clay with column with
stone Geotextile

Settlement in mm
column 20

25
C
15
S
Settlement in mm

20

10

15
5

10
0
0 5 10 15 20 25
Pressure in kN/m2
5
Fig. 4 Effect of Geotextile encapsulated stone column

0 In the Fig. 4, C represents the experiment with Clay soil alone,

0 5 10 15 20 S1 represents the experiment with stone column without
Pressure in kN/m2 geotextile and S represents the experiment stone column with
geotextile. By using geotextile the load bearing capacity of
stone column (S1) is increased by 21% for the 10 mm of
Fig. 3 Effect of Stone Column settlement and ultimate bearing capacity also increased by
60% compare to that without geotextile. Initially stone column
bears load, as load increases bulging occurs in stone column
The load bearing capacity of clay soil is increased by 74% due but in case of encapsulated stone column bulging reduces
to the installation of stone column for 10 mm settlement hence the ultimate load and settlement improves.
whereas the ultimate load capacity of clay soil is increased by
52%.
From pressure settlement curve of stone column, initially Effect of Quarry dust
stone column bears the load and after bulging settlement
increases rapidly. The stone chip in the stone column is replaced by quarry dust
with varying proportion in order to reduction the cost of the
stone column. The percentage of quarry dust varies as 30 %,
Effect of geotextile 50% 70%, 100%. The pressure settlement behavior for column
is as shown in Fig. 5.
To keep the stones of the column intact, the column is covered
with geotextile and the stone column is encapsulated by the

Paper No. 8.11 4

 35

Table 4 Results for Various Proportions of Quarry dust in

S4 stone column
30

S5
Pressure at 5 Pressure at Ultimate
25
Proportion mm 10 mm load
C S3 of column settlement settlement capacity
S
(KN/m²) (KN/m²) (KN/m²)
C
S2 3.34 5.36 7.10
Settlement in mm

20
S1
6.37 9.30 10.60
S
15 7.25 14.20 17.00
S2
S 70%+ Q 11.8 17.15 18.60
10 30%
S3
S 50% + 12.07 18.40 17.40
Q50%
5 S4
S 30%+ Q 6.0 11.2 16.50
70%
S5
0 9.847 16.067 17.50
Q (100%)
0 10 20 30 40

Pressure in kN/m2
C-Clay alone
S - stone column with Geotextile CONCLUSIONS
S2- 70 %Stone and 30% QD
S3- 50% Stone and 50%QD
The use of stone column is accepted as a means for ground
S4- 30%Stone +70% QD
improvement in soft clayey soils. The cost of construction
mainly depends on the cost of stone using for filling the stone
S5- 100% QD
column. Here an alternative is thought of, to replace partially,
the stones filling the column by cheaper materials. The
Fig. 5. The effect of various proportion of Quarry dust following observations could be made from this study.

• Stone column improves the bearing capacity and

In the figure 5, S5 represents the experiment with 100%quarry settlement behavior of soft soil.
dust, S4 represents the 30% stone and 70% quarry dust , S3 • Encasing the stone column with geotextile result in an
represents the 50% stone and 50% quarry dust , S2 represents increase in load carrying capacity and reduction in
the 70% stone and 30% quarry dust and S represents the 100% settlement when compared to that with the case without
stone inside the stone column. geotextile.
• A portion of stone in the column can be replaced by
Load bearing capacity for the system corresponding to the test quarry dust without affecting the strength of the improved
conditions for S2, S3 and S5 were increased by 21%, 29.5%, ground
13.14% respectively when it is compared to S (100% stone • From the studies it is revealed that the replacement of
enclosed in geotextile), for 10mm settlement. For the case of 30% (by weight) of stones by quarry dust can be possible
S4, a small reduction in capacity is observed with respect to without affecting the strength and performance of the
other values, as can be observed from Table 4. The increment system.
in the load bearing capacity is may be due to fill of void by • Further studies in this direction have to be conducted so
quarry dust. But there is a very small difference in the as to get more understanding of the system specially in
ultimate load capacity due to varying proportion of quarry dust the context of liquefaction.
in stone column with geotextile.

Paper No. 8.11 5

REFERENCES

Deshpandey, P.M and Vyas, A.V., [1996]. “Interactive

encased stone column foundation”, Sixth international
conference and exhibition on piling and deep foundation,
DFI’96, ISSMFE, Bombay,ppl-19.

Hughes, J.M.O and Withers, N.J., [1974]. “Reinforcing of soft

cohesion soils with stone columns”, Ground Engineering, vol.
7, No. 3 pp. 42-42 and pp. 47-49.

Malarvizhi S.N and llamparuthi K., [2002]. “Load versus

Settlement of Clay bed stabilized with Stone & Reinforced
Stone Column”, Anna University.

Mitchel, J.K. and Huber, T.R. [1985]. “Performance of a stone

column foundation”, Journal of Geotechnical Engineering,
Vol.111, No.2, ASCE.

Mitra,S. and Chatopadhyay, B.C. [1999]. “Stone Columns and

Design limitations” Proc. Of Indian Geotechnical Conference
held at Calcutta, 201-205.

Rao G. V and Balan K., [2000]. “Coir Geotextile Engineering

Trends”, Arenor printers, New Delhi.

Shanker, K. and Shroff, A.V. [1997]. “Experimental Studies

on Floated Stone Column in Soft Kaolinite Clay”, Proc. Of
Indian Geotechnical Conference held at Vadodara, pp. 265-
268.

Paper No. 8.11 6