Scribd
Upload
415 views

Structural Design Basic Report

This document outlines the structural design basis for a proposed Ground+1 villa called 'HAVEN' in Ayanambakkam, Thiruverkadu. The structure will be a reinforced concrete framed building designed using STAAD Pro software. A deep foundation system using piles will be adopted based on soil test results. Slabs will be conventional slabs. Load combinations including dead, live, wind and seismic loads will be considered as per relevant Indian codes for structural analysis and design.

Uploaded by

vaidehisarathy1857
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
415 views

Structural Design Basic Report

This document outlines the structural design basis for a proposed Ground+1 villa called 'HAVEN' in Ayanambakkam, Thiruverkadu. The structure will be a reinforced concrete framed building designed using STAAD Pro software. A deep foundation system using piles will be adopted based on soil test results. Slabs will be conventional slabs. Load combinations including dead, live, wind and seismic loads will be considered as per relevant Indian codes for structural analysis and design.

Uploaded by

vaidehisarathy1857
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

‘HAVEN’ Structural Design Basis Report

PROPOSED CONSTRUCTION OF GROUND+1 VILLA ‘HAVEN’ AT


AYANAMBAKKAM, THIRUVERKADU.

PROJECT BRIEF

This report sets out the basic parameters used for the structural design of the
proposed construction of Ground plus one proposed villa ‘HAVEN’ at Ayanambakkam,
Thiruverkadu. This has been updated to incorporate the current information on the
structure.

STRUCTURAL SYSTEM

The structural system adopted is as below, based on preliminary analysis and


design, which have bean elucidated later in this report.

 The building is basically a RC framed structure comprising of G+1 floors.


The analysis and design are done using STAAD Pro software.

 The foundation System comprises of deep foundation (pile) is adopted as per soil
Test report.

 All slabs are designed as conventional slabs.

LOAD DATA

(I) DEAD LOAD

Self-weight of the materials shall be calculated on the basis of unit weights


given in IS: 875 (PART I)

* Unit weight of concrete - 25 KN/m3

* Unit weight of Bricks - 20 KN/m3

* Floor finishes considered - 2 KN/m2

C. Kannan B.E., M.E (Structure)


Consulting engineer
‘HAVEN’ Structural Design Basis Report

(II) LIVE LOAD

On the basis of intended occupancy and uses, the loading shall be base on
IS: 875 (PART II)

(III) WIND LOAD

Wind loads for design of structures shall be based on the design wind
speeds arrived on IS: 875 (PART III)

The parameters for calculation of design wind speed as per IS: 875
(PART III) are as follows.

Basic wind speed (Vb) : 50 m/sec.

Risk coefficient, K1

(If design life of Structure is taken as 44 yrs) : 1.0

Terrain, Height, Structure size factor, K2 : To suit of the structure

For terrain category-4 and


class C appropriate is 0.67

Topography factor, K3 : 1.0

Design wind speed (Vz) : Vb x K1 x K2 x K3

Design wind pressure (Pz) : 0.6Vz2

: 0.6 x 33.52

: 0.673 kN/m2

C. Kannan B.E., M.E (Structure)


Consulting engineer
‘HAVEN’ Structural Design Basis Report

(IV) SEISMIC LOAD

Seismic loads for design of structure shall be considered as per

IS 1893-2002.

Zone : III

Zone factor : 0.16

Importance factor : 1

Response Reduction factor : 3.0

DESIGN LOAD COMBINATION

The proposed building is designed using the limit state method with
appropriate factors as per IS: 456-2000.

The load combinations are as follows

Load Combination

1.0 (DL+LL)

1.0(DL+WLX)

1.0(DL-WLX)

1.0(DL+WLZ)

1.0(DL-WLZ)

1.0(DL+SLX)

1.0(DL-SLX)

1.0(DL+SLZ)

1.0(DL-SLZ)

C. Kannan B.E., M.E (Structure)


Consulting engineer
‘HAVEN’ Structural Design Basis Report

1.0DL+0.8LL+0.8WLX

1.0DL+0.8LL-0.8WLX

1.0DL+0.8LL+0.8WLZ

1.0DL+0.8LL-0.8WLZ

1.0DL+0.8LL+0.8SLX

1.0DL+0.8LL-0.8SLX

1.0DL+0.8LL+0.8SLZ

1.0DL+0.8LL-0.8SLZ

Where

DL - Dead load

LL - Live load

WLX, WLZ - Wind load in X and Z direction

SLX, SLZ - seismic load in X and z direction.

ADDITIONAL CRITERIA

1. The structure is idealized as 3d frame and analyzed using software package

(STAAD Pro) for both vertical and lateral loads.

2. The lateral loads include wind loads and earthquake loads, seismic loads of medium

And moderate intensity of Zone III is considered for analysis and design puropose.

3. The foundation is designed for critical un-factored load combinations.

4. The super structure members are designed for actual flexure, shear and forces.

5. The structure is analyzed for specific loads (Dead and live loads) and for the load

Combinations given in relevant codes.

C. Kannan B.E., M.E (Structure)


Consulting engineer

You might also like