Scribd
Upload
67 views

Experiment No. 2: HARSH SOHNI-2017120060 AYUSH SINGH-2017120058 To Design A Monopole Antenna

The document describes an experiment to design a monopole antenna using HFSS simulation software. Key steps include drawing a cylindrical monopole conductor and assigning it as a perfect electric conductor. A lumped gap source is added to provide excitation. A radiation boundary is created and assigned. Frequency sweeps and various parameter analyses are run through solutions and reports to characterize the antenna performance.

Uploaded by

Ayush Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
67 views

Experiment No. 2: HARSH SOHNI-2017120060 AYUSH SINGH-2017120058 To Design A Monopole Antenna

The document describes an experiment to design a monopole antenna using HFSS simulation software. Key steps include drawing a cylindrical monopole conductor and assigning it as a perfect electric conductor. A lumped gap source is added to provide excitation. A radiation boundary is created and assigned. Frequency sweeps and various parameter analyses are run through solutions and reports to characterize the antenna performance.

Uploaded by

Ayush Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 8

Experiment No.

HARSH SOHNI-2017120060

AYUSH SINGH-2017120058

AIM- To design a monopole antenna.

SOFTWARE- High Frequency Simulation Software.


Theory:
A monopole antenna is a class of radio antenna consisting of a straight rod-
shaped conductor, often mounted perpendicularly over some type of conductive
surface, called a ground plane. The driving signal from the transmitter is applied,
or for receiving antennas the output signal to the receiver is taken, between the
lower end of the monopole and the ground plane. One side of the antenna
feedline is attached to the lower end of the monopole, and the other side is
attached to the ground plane, which is often the Earth. This contrasts with a
dipole antenna which consists of two identical rod conductors, with the signal
from the transmitter applied between the two halves of the antenna.
The monopole is a resonant antenna; the rod functions as an open resonator for
radio waves, oscillating with standing waves of voltage and current along its
length. Therefore, the length of the antenna is determined by the wavelength of
the radio waves it is used with. The most common form is the quarter-wave
monopole, in which the antenna is approximately one quarter of the wavelength
of the radio waves. The monopole antenna was invented in 1895 by radio pioneer
Guglielmo Marconi; for this reason it is sometimes called the Marconi
antenna.Common types of monopole antenna are the whip, rubber ducky,
helical, random wire, umbrella, inverted-L and T-antenna, inverted-F, mast
radiator, and ground plane antennas.Like a dipole antenna, a monopole has an
omnidirectional radiation pattern: it radiates with equal power in all azimuthal
directions perpendicular to the antenna. However, the radiated power varies with
elevation angle, with the radiation dropping off to zero at the zenith of the
antenna axis. It radiates vertically polarized radio waves.
Procedure:
Following are some of the steps which are to be followed in
simulating the antenna: 1. To begin working with
geometries, you must insert an HFSS design. Right-
Click the project file and select Insert -> Insert HFSS Design from the
menu.
2. After the successful creation of the design we need to draw a cylinder.
For this we will use the 3D modelling toolbar,using the Draw Cylinder
button from the toolbar. Choose 3 Arbitrary points inside the drawing
area and the cylinder is drawn

3. To create a cylinder of a desired dimension we can go to edit properties


and edit the required field such as Length, Radius, Position,etc. The
material of this cylinder must be PEC(perfect electric conductor)
4. Since it is a monopole antenna we will only require one cylinder. The
next step will be to make the gap source
5. Using the 3D toolbar we can draw a rectangle of arbitrary dimensions.
The plane for this needs to be chosen very wisely.
6. Having fed in the appropriate dimensions, the sheet needs to be converted
into a Lumped Gap Source. This will provide excitation to the antenna.
This excitation is commonly used when the far field region is of primary
interest. In the project explorer, right-click Excitation -> Assign ->
Lumped Port.
7. Now we need to create a circle of given radius with its center at the
origin. We need to assign a PerfE to the circle
8. A radiation boundary is created so that far field information may be
extracted from the structure. To obtain the best result, a cylindrical air
boundary is defined with a distance of λ/4. From the toolbar, select Draw
Cylinder and choose 3 arbitrary points within the model window.
9. With the geometry complete, the actual radiation boundary may now be
assigned. From the 3D toolbar select face from the drop down window
10. With all faces selected, right-click the Boundary icon in the object
explorer and select Boundary -> Assign -> Radiation.
11.After successful completion of the above mentioned steps we can add a
solution step keeping all the parameters to their default value
12. To view the frequency response of the structure, a frequency
sweep must be defined. From the project explorer select Setup1 -> Add
Sweep. The sweep parameters need to be edited as per the requirement of
the project.
13. After this, the user must be ready to analyze the design, but before
this we need to verify using the verification button on the 3D toolbar.
Having done the analysis we are now in a position to create a report.
14. Various graphs and various parameters can be analysed to look at
various outputs and required simulations can be achieved.
Procedures to be followed during analysis:
1. For simulation a solution must be defined to display the
desired data. We are primarily interested in the frequency
response of the structure. We will also explore HFSS's
ability to calculate general antenna parameters such as
directivity, radiation resistance, radiation efficiency, etc... .
From the project explorer, select Analysis -> Add Solution
Setup.
2. All the settings are to be left as default. To view the
frequency response of the structure, a frequency sweep must
be defined. From the project explorer select Setup1 -> Add
Sweep.
3. The next step is to analyse the model created. Before that a
validation check needs to be performed by selecting from
the 3D toolbar. If everything is correct the user should see:
4. Analyze the structure by clicking
5. After completion of the analysis, we will create a report to
display both the resonant frequency and also the radiation
pattern. Click on the heading HFSS and select Results ->
Create Reports.
6. Depending upon our requirements for the simulation and
desired output we can choose the report we need to look at.
For s,z a rectangular plot is preferred and for other radiations
we can choose from a wide range from 3D to other plots
s parameter-

VSWR

Z-parameter
3-D rectangular plot

You might also like