JOB NO. : Rev. No.

OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
BUILDING : Approved By

ANCHOR BOLT & BASE PLATE DESIGN (FIXED BASE)

SECTION SIZES:
Depth of Web of column, dw = 625 mm
Thickness of column web, tw = 6 mm
Width of column flange, bf = 300 mm
Thickness of column flange, tf = 10 mm

BASE PLATE DETAILS: e1 p1

Yield stress of Plate, Fy = 345 Mpa
Length of Base Plate, L = 825 mm
Width of Base Plate, B = 400 mm
Thickness of Base Plate, t = 20 mm
Cantilever along Length = 90 mm

ANCHOR BOLT DETAILS: g1

Dia. Of Anchor Bolt near to flanges, db = 20 mm
Anchorage length Of bolt, l = 700 mm
Anchorage length Of bolt acted for Bond, l = 780 mm
No. of Bolts nearer to flanges, N1 = 4
Spacing of Bolts, g = 320.00 mm
Spacing of Bolts, p1 = 150.00 mm
Spacing of Stiffeners, p2 = 309.00 mm
Edge Distance of Bolts, e1 = 40.00 mm
Edge Distance of Bolts, e2 = 40.00 mm
Cantiliver on Both Side=Lz 94.00
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
Diameter Of Anchor Bolt at centre, d'b = mm
Anchorage length Of bolt at Centre, l' = 0 mm Upward Force
No. of Bolts at centre, N2 = 0 Downward Force
Grade of Bolts = 4.6 Anticlockwise Moment
Ultimate Tensile Streass of the Bolt =fub 400.0 Clockwise Moment
Yield Stress of bolt fyb = 0.6fub 240.0
STIFFENER DETAILS:
Thickness of stiffener, ts = 6 mm
width of stiffener, w = 100 mm Notes : We are not taking the adv
Height of stiffener, h = 200 mm the major axis.

Pedestal Details:
Grade of Concrete = M 20 20.0
Maximum Bearing Pressure, Fb = 11.40 Mpa IS 800:2007 Cl 7.4.1
Length of Pedetsal = 925 mm
Width of Pedetsal = 500 mm
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
LOAD DATA (STAAD OUTPUT)
LOAD COMB. Shear Fx, KN Vertical Fy, KN Shear Fz, KN Moment Mx, KNm
501 (1.5XDL+1.5XLL) 22.6 81.1 1.4 0.0
509 (0.9XDL+1.5XWL8) -39.5 -73.2 -1.5 -0.1
517 (1.5XDL+1.5XWL8) -36.9 -55.6 -1.2 -0.1
522 (1.2XDL+1.2XLL+1.2XWL5) 17.5 56.9 1.0 0.0
530 (1.2XDL+1.2XLL+0.6XWL5) 17.8 60.9 1.1 0.0
547 (0.9XDL+1.5XEQ-X) 5.2 26.8 0.4 0.0
543 (1.5XDL+1.5XEQ-X) 7.7 44.4 0.7 0.0
535 (1.2XDL+1.2XLL+1.2XEQ-X) 2.0 309.6 -0.1 -0.7
539 (1.2XDL+1.2XLL+0.6XEQ-X) 1.0 309.6 -0.1 -0.7
550 1.5XDL + 1.5XLL + 1.5XCL1 22.6 123.7 2.1 -0.2
565 1.2XDL + 1.2XLL + 1.05XCL2 + 0.6XWL5 17.7 146.0 2.4 -0.3
589 1.2XDL + 1.2XLL + 0.53XCL2 + 1.2XWL5 17.5 99.9 1.7 -0.2
606 1.2XDL + 1.2XLL + 1.05XCL2 + 0.6XEQ-X 18.5 150.1 2.5 -0.3
618 1.2XDL + 1.2XLL + 0.53XCL2 + 1.2XEQ-X 19.0 108.1 1.8 -0.2

CALCULATIONS FOR TENSION IN BOLTS

CASE I : 501 (1.5XDL+1.5XLL) SP 40 PAGE NO-25

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force 81.092 kN & Moment 65.741 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)-81.092x1000x372.5-65.741x 10^6 =0
=> K^2- 3K +0.205=0
K1= 2.930 OR K2= 0.070
Y=Kx(L-e2)= 2.931x785 OR Y= 0.07x785
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By

Y= 2300.11 OR 54.89 mm
=> 54.89 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 44.1 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.1 KN T = 44.2 KN
Total Tension in bolts, T = 44.2 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
81.1/(825x400) +-65.8x6/(400x825^2) + -0.1x6/(825x400^2) 1.7 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE II : 509 (0.9XDL+1.5XWL8)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Tensile Force 73.223 kN & Moment 114.895 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) + P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)+73.223x1000x372.5-114.895x 10^6 =0
=> K^2- 3K +0.188=0
K= 2.9363 OR 0.0637
Y=Kx(L-e2)= 2.937x785 OR 0.064x785

Y= 2304.98 OR 50.02 mm
=> 50.02 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 187.3 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.2 KN T = 187.5 KN
Total Tension in bolts, T = 187.440 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
-73.3/(825x400) +114.9x6/(400x825^2) + -0.1x6/(825x400^2) 2.31 MPa

CASE III : 517 (1.5XDL+1.5XWL8)

Tensile Force 55.579 kN & Moment 107.33 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) + P x ( L/2 - e2 ) - Mz = 0

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
=> 1/2x11.4 x785^2x K x400x(1-1/3K)+55.579x1000x372.5-107.33x 10^6 =0
=> K^2- 3K +0.185=0
K= 2.9370 OR 0.0630
Y=Kx(L-e2)= 2.938x785 OR 0.063x785
Y= 2305.56 OR 49.44 mm
=> 49.44 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 168.3 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.2 KN
Total Tension in bolts, T = 168.5 KN T = 168.6 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
-55.6/(825x400) +107.4x6/(400x825^2) + -0.1x6/(825x400^2) 2.2 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE IV : 522 (1.2XDL+1.2XLL+1.2XWL5)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Tensile Force = 56.939 kN & Moment = 58.804 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) + P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)+56.939x1000x372.5-58.804x 10^6 =0
=> K^2- 3K +0.081=0
K= 2.9730 OR 0.0270
Y=Kx(L-e2)= 2.973x785 OR 0.028x785

Y= 2333.80 OR 21.20 mm
=> 21.20 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 105.3 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.1 KN
Total Tension in bolts, T = 105.4 T = 105.4 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
57/(825x400) +-58.9x6/(400x825^2) + -0.1x6/(825x400^2) 1.5 MPa

CASE V : 530 (1.2XDL+1.2XLL+0.6XWL5)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 60.906 kN & Moment = 55.698 kNm
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0
=> 1/2x11.4 x785^2x K x400x(1-1/3K)-60.906x1000x372.5-55.698x 10^6 =0
=> K^2- 3K +0.168=0
K= 2.9431 OR 0.0569
Y=Kx(L-e2)= 2.944x785 OR 0.057x785

Y= 2310.36 OR 44.64 mm
=> 44.64 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 40.9 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.1 KN
Total Tension in bolts, T = 41.0 KN T = 41 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
61/(825x400) +-55.7x6/(400x825^2) + -0.1x6/(825x400^2) 1.4 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE VI : 547 (0.9XDL+1.5XEQ-X)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 26.767 kN & Moment = 19.258 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)-26.767x1000x372.5-19.258x 10^6 =0
=> K^2- 3K +0.063=0
K= 2.9791 OR 0.0209
Y=Kx(L-e2)= 2.98x785 OR 0.021x785

Y= 2338.55 OR 16.45 mm
=> 16.45 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 10.7 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.1 KN
Total Tension in bolts, T = 10.8 KN T = 10.9 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
26.8/(825x400) +-19.3x6/(400x825^2) + -0.1x6/(825x400^2) 0.5 MPa

CASE VII : 543 (1.5XDL+1.5XEQ-X)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 44.411 kN & Moment = 26.823 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
=> 1/2x11.4 x785^2x K x400x(1-1/3K)-44.411x1000x372.5-26.823x 10^6 =0
=> K^2- 3K +0.093=0
K= 2.9688 OR 0.0312
Y=Kx(L-e2)= 2.969x785 OR 0.032x785

Y= 2330.52 OR 24.48 mm
=> 24.48 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 11.4 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.2 KN
Total Tension in bolts, T = 11.6 KN T = 11.6 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
44.5/(825x400) +-26.9x6/(400x825^2) + -0.1x6/(825x400^2) 0.7 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE VIII : 535 (1.2XDL+1.2XLL+1.2XEQ-X)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 309.607 kN & Moment = 9.194 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)-309.607x1000x372.5-9.194x 10^6 =0
=> K^2- 3K +0.266=0
K= 2.9086 OR 0.0914
Y=Kx(L-e2)= 2.909x785 OR 0.092x785

Y= 2283.24 OR 71.76 mm
=> 71.76 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= -146.0 KN Compressive Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 2.1 KN
Total Tension in bolts, T = -143.9 KN T = -144 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
309.7/(825x400) +-9.2x6/(400x825^2) + -0.7x6/(825x400^2) 0.7 MPa

CASE IX : 539 (1.2XDL+1.2XLL+0.6XEQ-X)

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 309.607 kN & Moment = 4.597 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
=> 1/2x11.4 x785^2x K x400x(1-1/3K)-309.607x1000x372.5-4.597x 10^6 =0
=> K^2- 3K +0.257=0
K= 2.9121 OR 0.0879
Y=Kx(L-e2)= 2.913x785 OR 0.088x785

Y= 2285.97 OR 69.03 mm
=> 69.03 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= -152.2 KN Compressive Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 2.1 KN
Total Tension in bolts, T = -150.2 KN T = -150.2 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
309.7/(825x400) +-4.6x6/(400x825^2) + -0.7x6/(825x400^2) 0.8 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE X : 550 1.5XDL + 1.5XLL + 1.5XCL1

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 123.671 kN & Moment = 65.741 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)-123.671x1000x372.5-65.741x 10^6 =0
=> K^2- 3K +0.239=0
K= 2.9182 OR 0.0818
Y=Kx(L-e2)= 2.919x785 OR 0.082x785

Y= 2290.78 OR 64.22 mm
=> 64.22 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 22.8 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.5 KN
Total Tension in bolts, T = 23.3 KN T = 23.3 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
123.7/(825x400) +-65.8x6/(400x825^2) + -0.2x6/(825x400^2) 1.8 MPa

CASE XI : 565 1.2XDL + 1.2XLL + 1.05XCL2 + 0.6XWL5

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 146.005 kN & Moment = 55.774 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
=> 1/2x11.4 x785^2x K x400x(1-1/3K)-146.005x1000x372.5-55.774x 10^6 =0
=> K^2- 3K +0.236=0
K= 2.9194 OR 0.0806
Y=Kx(L-e2)= 2.92x785 OR 0.081x785

Y= 2291.75 OR 63.25 mm
=> 63.25 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= -1.8 KN Compressive Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.9 KN
Total Tension in bolts, T = -0.9 KN T = -1 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
146.1/(825x400) +-55.8x6/(400x825^2) + -0.3x6/(825x400^2) 1.7 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE XII : 589 1.2XDL + 1.2XLL + 0.53XCL2 + 1.2XWL5

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 99.894 kN & Moment = 58.842 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)-99.894x1000x372.5-58.842x 10^6 =0
=> K^2- 3K +0.206=0
K= 2.9300 OR 0.0700
Y=Kx(L-e2)= 2.931x785 OR 0.07x785

Y= 2300.05 OR 54.95 mm
=> 54.95 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 25.4 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.5 KN
Total Tension in bolts, T = 25.9 KN T = 25.9 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
99.9/(825x400) +-58.9x6/(400x825^2) + -0.2x6/(825x400^2) 1.6 MPa

CASE XIII : 606 1.2XDL + 1.2XLL + 1.05XCL2 + 0.6XEQ-X

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 150.093 kN & Moment = 55.833 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
=> 1/2x11.4 x785^2x K x400x(1-1/3K)-150.093x1000x372.5-55.833x 10^6 =0
=> K^2- 3K +0.239=0
K= 2.9182 OR 0.0818
Y=Kx(L-e2)= 2.919x785 OR 0.082x785

Y= 2290.82 OR 64.18 mm
=> 64.18 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= -3.8 KN Compressive Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.9 KN
Total Tension in bolts, T = -2.9 KN T = -2.9 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
150.1/(825x400) +-55.9x6/(400x825^2) + -0.3x6/(825x400^2) 1.7 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CASE XIV : 618 1.2XDL + 1.2XLL + 0.53XCL2 + 1.2XEQ-X

Calculating the Y & Tension in the Bolt as per SP 40 Page 24 for analysis only.
Compressive Force = 108.069 kN & Moment = 58.96 kNm

=> 1/2 x Fb x(L-e2)^2 xK x B x (1-1/3 K) - P x ( L/2 - e2 ) - Mz = 0

=> 1/2x11.4 x785^2x K x400x(1-1/3K)-108.069x1000x372.5-58.96x 10^6 =0
=> K^2- 3K +0.212=0
K= 2.9276 OR 0.0724
Y=Kx(L-e2)= 2.928x785 OR 0.073x785

Y= 2298.20 OR 56.80 mm
=> 56.80 mm

Tension in bolts due to Major Moment, T1 =1/2xFbxYxB ± P= 21.4 KN Tensile Force

Tension in bolts due to Minor Moment, T2 =M/(B-e1*2)= 0.5 KN
Total Tension in bolts, T = 22.0 KN T = 22 KN

Check for Base Plate Under Bearing Pressure

(P/(B x L)) ± (6 x Mz / B x L2) ± (6 x Mx / L x B2) < Fb
108.1/(825x400) +-59x6/(400x825^2) + -0.2x6/(825x400^2) 1.6 MPa
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
MAXIMUM FORCE IN BOLTS = 187.4 KN Load Case=
Maximum force in each bolt in tension = 46.9 KN

Check For Tension:

Tension per bolt 'Tb' =Flange Force/N = 46.86 kN

Tension Capacity of the Bolt (Tnb)=0.9fub x An=0.9x400xЛ/4x17^2= 81.72 kN IS 800:2007 Cl 10.3.5
< fyb x Asb x Ymb/Ym0=240x Л/4 x 20^2 x (1.25/1.1) 85.68 kN
Hence , Tnb = 81.72 kN
Capacity of Bolt (Tdb)=Tdb= Tnb/Ymb =81.72/1.25 65.38 kN > 46.86
* Provide 8.0 no.s of 20 mm dia. Bolts

Calculation for anchor bolt length

Permissible bond stress of Plain bars in tension , ζbd = 1.2 N/mm2
Overall Anchorage length required = T/(Л x ζbd x (20 )
Thus Doverall = 621.5 mm [OVERALL ANCHORAGE LENGT

Check For Shear :

NOTE : It is assumed that the whole of Shear or Horizontal force is transferred to the pedestal through Shear Lug and bolt is not carrying a
combined tension & shear is not required. Bolt is designed only to take care of the tension.

Design of Shear Lug:

LOAD DATA (STAAD OUTPUT) FOR MAXIMUM SHEAR ONLY
LOAD COMB. Shear Fx, KN Vertical Fy, KN Shear Fz, KN Moment Mx, KNm
509 (0.9XDL+1.5XWL8) -39.5 -73.2 -1.5 -0.06

Coefficient of friction 'µ' = 0.45 From IS 800:2007 7.4.1

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
Max Shear Force= Vx= 39.45

Design of Shear Lug for Vx :

Area of Shear Lug= Alg=V/(.45fck) 4383.7 mm2 IS 800:2007 Cl 7.4.1

Assuming width of Shear Lug = w 200.0 mm

Assuming the Height of Grout Depth= 50.0 mm
Height of Shear Lug = H-G =Alg/w 21.92 mm Grout
Reuired Depth of Shear Lug= H = 72.0 Say 150 mm
The Clantilever end moment = Mlg =(V/w)x(H-G/2)
Mlg= 9271.46 Nmm/mm width
Thickness of Shear Lug=tlg= 4.0Mlg/(fy/ym0)
tlg= 10.87 Say 12 mm
Hence provide shear lug of Width=200mm x Depth=150mm x Thickness=12mm Minimum Size of Shear Lug

Check for Weld in Shear Lug:

Size Fillet Weld 'W'= 6 mm Throat size of Weld 'tt'= 0.7 x W
Design Strength of fillet Weld = (Fu/√3)/fm0)=(480/√3)/1.25 221.70 N/mm2 As per 800-2007 Cl 10.5.7.1.1
Stress developed in Weld = Vx/(w*tt) = 39.453x 1000 /(200x4.242) = 46.50 N/mm 2

Hence Safe
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By

Calculation of Plastic Secion modulus of Rectangular Section

t/4
t Ac
At
b t/4
Zp=bxt/2xt/4+bxt/2xt/4 =bt2/8+bt2/8=bt2/4

fy/fm0<M/Zp => Zp<M/(fy/fm0) => t2 = 4M/(bx(fy/fm0))

t = 4M/(bx(fy/fm0))

CALCULATION FOR MAXIMUM BENDING MOMENT IN BASE PLATE

ON TENSION SIDE :
Moment Due to Tension= Tesion Force x Projection= Tb x No.of bolt outer facexLz =46.86x2x176.71
M = 16.6 KN-m

Thickness of base plate required for tension = 4M/(fy/fm0) = 26.8 mm

ON COMPRESSION SIDE (DL+LL+CR):

Moment due to compression in plate = Bx(Fb1xe2xe2/2 +1/2xFb2xe2x2/3xe2) Refer SP 40 Page 24
M=400x(5.1x40x40/2+1/2X6.3x40x40x2/3) 2.98 KN-m

Thickness of base plate required for compression = 6M/1.2(fy/fm0) = 10.9 mm

BASE PLATE SHOULD NOT BE
LESS THAN THIS THICK.
Maximum thickness of base plate without Stiffners=twos 26.8 mm

Check for Min Thickness of Baseb plate as per IS 800:2007 7.4.3.1

JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
Thickness of base plate t due to downward force= 2.5w(a -0.3b )Ym0/fy > tf
2 2

Note: Check is done for DL+LL+CL only for axial compressive load
where w = pr. Due to downward force
a = 90 mm Max Projecttion
b = 50 mm Min projection
w = 0.246 N/mm2
Ym0 = 1.100
t= 3.79 Hence Safe
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
CALCULATION OF BASE PLATE THK. WITH STIFFNERS
Calculation for Elastic Section Modulus
Minimum Plastic Sectional Modulus reqd. =Bxtwos^2/4=400x26.81^2/4 = 71877.61 mm3
Plastic Sectional Modulus w/o Stiffeners= Bxt^2/4 =400x20^2)/4 = 40000.00 mm3

Assuming that Depth of NA Axis lies within Base Plate. (Theory of Plasticity By Ac=At=A/2) h
Plastic N.A from Bottom = h1 = (bx t +hxt1)/(2xb) = 11.50 mm Assumption is Right

Plastic Section Modulus = Bxh1xh1/2+Bx(t-h1)*(t-h1)/2+hxt1x(h/2+(t-h1)) h1 t

=400x11.5x11.5/2 +400x8.5x8.5/2 + 200x6(200/2+8.5) 1

Zp = 171100 mm3

Plastic Section Modulus of Base plate with stiffeners= Zp 171100.00 mm3 > 71877.61 mm3

Provide Base Plate 825 mm x 400 mm x 20 mm with 4 nos. 20 dia. nearer to the flanges & 0 nos. dia. at the centre w
CHECKING OF POLATE THICKNESS BY W.T MOODY

Base Plate Thickness :-

Exterior Panel : Two Contineous Edge is Fixed & Two Contineous Edge is Free Interior Panel :Three Contineous E

a1

d1 d1
a1= 90 mm a1=
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
d1 = 197 mm d1 =

a1/d1 = 0.457 a1/d1 =

Assuming Y/b 1 Assuming Y/b

Assuming X/a 0 Assuming X/a

Moment Coefficient a3 = 0.109 after interpolation Moment Coefficient a3 =

For Coefficient See Page 33 of Moment & Reaction for rectangular plate by W.T Moody For Coefficient See Page 7 of Momen

Mp = a3 x s con-max x d12 = 9762.1296997333 Nmm Mp = a3 x (s con-max x (C-e)/C) x d1

t requd = (5 x Mp/fy/ym0 ) 0.5 = 12.48 mm t requd =

SUMMARY
PLATE SIZE = 825x400 MM .
PLATE THICKNESS = 20 MM
JOB NO. : Rev. No.
OWNER : Date
CONSULTANT : Designed By
MAIN CONTRACTOR : Checked By
PROJECT : Recommded By
DESIGN FOR WELDED CONNECTION BETWEEN COLUMN PLATE

Size of Fillet Weld 'W' = 8 mm

Throat size of weld 'tt'=0.707W 5.7 mm
Design Strength of fillet Weld = Fu/√3)/fm0=(610/√3)/1.25 281.75 N/mm2 As per 800-2007 Cl 10.5.7.1.1
Maximum Moment = 114.90 kNm Axial Force= 73.223 kN
Maximum Force in Weld between column & stiffeners=F= M/(Dw+2*Tf)+P/2 = 214743.28 N

715.8109431525 N/mm
Force Per unit length of weld in flange & Web of Column = F/m = F/((Dw+tf*2)/2+bf) 454.48

Stress in Fillet Weld = (F/m)/tt 80.35 N/mm2 < 281.75

 :
:
:
:
:
:

BASE PLATE DESIGN (FIXED BASE)

General Frames
Frame No. : 1
Node No. : 13
Detail : A
Location : SWC

e1 p1 p1 e1

b=197mm b=197mm

p2= 310 mm
a=154.75mm a=90mm

Fig. 1
 :
:
:
:
:

" -ve "

" +ve "
" -ve "
" +ve "

Notes : We are not taking the advantage of centre bolt as it is not take any tension in
the major axis.

IS 800:2007 Cl 7.4.1
 :
:
:
:
:
D OUTPUT)
Moment Mz, KNm
-65.7
114.9
107.3
-58.8
-55.7
-19.3
-26.8
-9.2
-4.6
-65.7
-55.8
-58.8
-55.8
-59.0

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

11.4 MPa

Fig. 2

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

11.4 MPa

Fig. 3

[HENCE SAFE]

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

11.4 MPa

Fig. 4

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

Fig. 5

11.4 MPa

[HENCE SAFE]

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

Fig. 6

11.4 MPa

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

Fig. 7

11.4 MPa

[HENCE SAFE]

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

Fig. 8

11.4 MPa

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

11.4 MPa

Fig. 9

[HENCE SAFE]

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

11.4 MPa

Fig. 10

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

309.6 MPa

Fig. 10

[HENCE SAFE]

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

0.0 MPa

Fig. 10

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

0.0 MPa

Fig. 10

[HENCE SAFE]

Refer SP 40 Page 24 to 25 for analysis only.

:
:
:
:
:

0.0 MPa

Fig. 10

[HENCE SAFE]
:
:
:
:
:

Refer SP 40 Page 24 to 25 for analysis only.

0.0 MPa

Fig. 10

[HENCE SAFE]
 :
:
:
:
:
509 (0.9XDL+1.5XWL8)

Hence OK

IS 456 : 2000 Cl 26.2.1.1

[OVERALL ANCHORAGE LENGTH REQUIRED IS SUFFICIENT]

d to the pedestal through Shear Lug and bolt is not carrying any of the Shear Force. Hence Check for Shear and
of the tension.

R MAXIMUM SHEAR ONLY

Moment Mz, KNm
114.90
 :
:
:
:
:

H
G

Shear Lug
m x Thickness=12mm Minimum Size of Shear Lug Fig. 11

4 mm
As per 800-2007 Cl 10.5.7.1.1
 :
:
:
:
:

a1 90.00
d1 197.00
a1/d1 0.46

Lz= (p1/2)2+(g/2)2
Lz = 176.71 mm

Refer SP 40 Page 24

71.76

Fb1=5.1 N/mm2
Fb=11.4 N/mm2
BASE PLATE SHOULD NOT BE Fb2=6.3 N/mm2
LESS THAN THIS THICK.
40 mm
Fig 12
:
:
:
:
:
 :
:
:
:
:

t1

1
1 Ac1
h h2
y
Ac2
t At h1
1

b b
Fig - 13
HENCE SAFE

20 dia. nearer to the flanges & 0 nos. dia. at the centre with 6 mm thk. Siffeners

Interior Panel :Three Contineous Edge is Fixed & One Edge is Free :-

a1

154.75 mm
 :
:
:
:
:
197 mm

0.79
0.75
1
0

Moment Coefficient a3 = 0.2000 after interpolation

For Coefficient See Page 7 of Moment & Reaction for rectangular plate by W.T Moody

Mp = a3 x (s con-max x (C-e)/C) x d12 = 17912.1645866667 kNm

(5 x Mp/246 ) 0.5 = 16.9 mm

 :
:
:
:
:
N BETWEEN COLUMN PLATE

As per 800-2007 Cl 10.5.7.1.1

N/mm

HENCE SAFE