Scribd
Upload
27 views

Microscope

A compound microscope has structural components that include the head, base, and arm. It contains two optical systems - eyepiece lenses that the user looks through, and objective lenses of varying magnification that are housed in the nosepiece. To use the microscope, a specimen is placed on the stage under the objective lenses and illuminated from below by the condenser and light source in the base. The user focuses on the specimen by adjusting the coarse and fine focus knobs and selects different objective lenses by rotating the nosepiece to view the specimen at increasing levels of magnification.

Uploaded by

Dinnich aa
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
27 views

Microscope

A compound microscope has structural components that include the head, base, and arm. It contains two optical systems - eyepiece lenses that the user looks through, and objective lenses of varying magnification that are housed in the nosepiece. To use the microscope, a specimen is placed on the stage under the objective lenses and illuminated from below by the condenser and light source in the base. The user focuses on the specimen by adjusting the coarse and fine focus knobs and selects different objective lenses by rotating the nosepiece to view the specimen at increasing levels of magnification.

Uploaded by

Dinnich aa
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

1.

Principle
A high power or compound microscope achieves higher levels of
magnification than a stereo or low power microscope. It is used to view smaller
specimens such as cell structures which cannot be seen at lower levels of
magnification. Essentially, a compound microscope consists of structural and optical
components. However, within these two basic systems, there are some essential
components that every microscopist should know and understand.
2. Part Of Microscope Binocular

STRUCTURAL COMPONENTS

The three basic, structural components of a compound microscope are the head, base
and arm.

a. Head/Body houses the optical


parts in the upper part of the
microscope
b. Base of the microscope supports
the microscope and houses the
illuminator
c. Arm connects to the base and
supports the microscope head. It is
also used to carry the microscope.

When carrying a compound microscope always take care to lift it by both the arm
and base, simultaneously.
OPTICAL COMPONENTS

There are two optical systems in a compound microscope: Eyepiece Lenses and
Objective Lenses:

a. Eyepiece or Ocular is what you look through at the top


of the microscope. Typically, standard eyepieces have a
magnifying power of 10x.
b. Eyepiece Tube holds the eyepieces in place above the
objective lens.
c. Objective Lenses are the primary optical lenses on a

microscope. They range from 4x-100x


and typically, include, three, four or five
on lens on most microscopes. Objectives
can be forward or rear-facing.
d. Nosepiece houses the objectives. The
objectives are exposed and are mounted
on a rotating turret so that different objectives can be conveniently selected.
Standard objectives include 4x, 10x, 40x and 100x although different power
objectives are available.
e. Coarse and Fine Focus knobs are used to focus
the microscope. Increasingly, they are coaxial
knobs - that is to say they are built on the same
axis with the fine focus knob on the outside.
Coaxial focus knobs are more convenient since
the viewer does not have to grope for a different
knob.
f. Stage is where the specimen to be viewed is placed. A mechanical stage is
used when working at higher magnifications
where delicate movements of the specimen
slide are required.
g. Stage Clips are used when there is no
mechanical stage. The viewer is required to
move the slide manually to view different
sections of the specimen.
h. Aperture is the hole in the stage through
which the base (transmitted) light reaches the
stage.
i. Illuminator is the light source for a microscope,
typically located in the base of the microscope. Most
light microscopes use low voltage, halogen bulbs
with continuous variable lighting control located
within the base.

j. Condenser is used to collect and focus the light from


the illuminator on to the specimen. It is located under
the stage often in conjunction with an iris diaphragm.

k. Iris Diaphragm controls the amount of light


reaching the specimen. It is located above the
condenser and below the stage. Most high quality
microscopes include an Abbe condenser with an
iris diaphragm. Combined, they control both the
focus and quantity of light applied to the
specimen.
3. Procedure

a. Turn on the illuminator. slowly increase the light intensity as the lamp heats
up quite quickly.

b. Place a slide or specimen on the stage with the sample


directly, fasten it to the stage with the stage clips.

c. Ensure the iris diaphragm is completely open, allowing


the maximum amount of light to reach the slide and the
lenses.

d. Rotate the nosepiece so that the objective lens with the lowest level of
magnification is directly above the sample. Reminder: Using lower
magnifications first helps to select the part of the specimen of interest and
then adjust further

e. Look through the binocular eyepieces and adjust the iris diaphragm until the
amount of light is satisfactory.

f. Turn the coarse adjustment knob until the specimen comes into broad focus.

g. Turn the fine adjustment knob until the specimen comes into sharp focus.

h. The viewer should then be able rotate the nosepiece to higher settings and
bring the sample into more and more detail with a minimal amount of
refocusing
i. In order to move your microscope safely, one hand should be under its base
for support and the other at its arm. Be sure to only switch off the microscope
when the lamp is set to the lowest intensity and always turn off the lamp
before moving the microscope.

You might also like