10th Biennial International Conference & Exposition

P 410

Effect of Seismic Wavelet Phase on Post Stack Inversion

Chirag Jain*

Summary

E&P industry now a days greatly depends on inversion for interpretation of the data. Seismic data may be inspected and
interpreted on its own without inversion, but this does not provide the most detailed view of the subsurface and can be
misleading under certain conditions. Because of its efficiency and quality, most oil and gas companies now use seismic
inversion to increase the resolution and reliability of the data and to improve estimation of rock properties including porosity
and net pay. Inversion can be defined as deriving a model to describe the subsurface from field data that is consistent with the
data.

Keywords: Inversion, Wavelet Phase, Quality Controls and Wavelet.

Introduction of the band limited nature of the seismic data. The lower
frequencies are most critical to rock properties, because it
Seismic inversion is the process of converting seismic leads to determining fluid, porosity, and all other reservoir
reflection data into seismic impedance. Seismic acoustic properties needed to make a drilling decision. Therefore a
impedance is the product of density and velocity. Acoustic low frequency trend model is necessary in order to really
impedance (AI) is a rock/layer property as it is related to find out what is going on in earth.
layers and not the interfaces. Since AI varies with
lithology, porosity, fluid content, depth, pressure and Seismic inversion depends on a number of parameters (low
temperature it can be used as a lithology indicator to map frequency model, wavelet phase, wavelength of wavelet,
flow units accurately, porosity indicator, hydrocarbon frequency of wavelet, etc.). A good wavelet is the core of
indicator and a tool for quantitative analysis. Therefore inversion. This investigation takes account of variation in
result of inversion greatly effects the interpretation and phase of wavelet keeping all other parameters same. Gulf
finally decision making in the industry. of Mexico Data set (Public domain) is used for the
experiment.
Theory and Method
Phase describes the relative timing relationships of the
Seismic inversion is based on the convolution model: various frequency components that make up the seismic
wavelet.
- Seismic trace is convolution of reflectivity R(t) with
wavelet W(t) plus noise First of all data is loaded and the quality controls are
N(t): S(t) = R(t)*W(t) + N(t) (Where * is convolution) applied to test the quality of data. Well to seismic tie is
- Assuming that the noise component is negligible: done using initial wavelet derived from the statistical
S(t) = R(t)*W(t) method. This is then followed by zero or minimum phase
wavelet estimation at the wells, where the reflectivity
It is better to work in frequency domain than in time series is known both from the well as well as from the
domain and so when we convert the above equation in seismic. Synthetic Ricker wavelets of 15, 30, 45, 60, 75,
frequency domain a problem arises: the lowest and the 90, 120, 150 and 180 degree phase are then generated.
highest frequencies will be missing. This happens because Each of above created synthetic Ricker wavelet is merged

118 – Opal Hostel, Indian School of Mines, Dhanbad-826004;

[email protected]
with the extracted wavelet to get 15, 30, 45, 60, 75, 90,
120, 150 and 180 degree amplitude-phase wavelet.

Figure 4 Phase spectra of all the extracted wavelet

overlapped

Trend model is then created for each case. These wavelets

and trend models are then used for seismic inversion to
find out the reflectivity series away from the well. Every
step is followed by the quality controls to check the
accuracy. The results are as follows:

Figure 5 Inverted impedance zero degree phase wavelet

Figure 1 Phase rotation of a zero phase wavelet

Figure 6 Inverted impedance 15 degree phase wavelet

Figure 2 All the extracted wavelets

Figure 7 Inverted impedance 30 degree phase wavelet

Figure 3 Amplitude spectra of all the extracted wavelet

overlapped

Figure 8 Inverted impedance 45 degree phase wavelet

2
 When zero degree phase wavelet is used for inversion,
results follows almost the same trend as the well data
follow. Thus indicating that inversion result is good. When
15 degree phase wavelet is used for inversion, it also
follows the geology of the area as described by well to an
extent which can be considered. However when we take
Figure 9 Inverted impedance 60 degree phase wavelet wavelet with phase 30 degree and greater the inversion
results disagree with the geology of the area, for instance
high impedance region becomes low impedance and
viceversa. For the case of 180 degree phase, the inversion
results show a relatively high impedance layer within
the low impedance layer with respect to the exact geology
of the area.

Conclusions
Figure 10 Inverted impedance 75 degree phase wavelet

Zero phase or minimum phase wavelets are the most

desirable for interpretation. The degree of variation in
phase of the input wavelet greatly effects the inversion
results. The higher the phase shift, the higher is the error
in impedance results.

Acknowledgment
Figure 11 Inverted impedance 90 degree phase wavelet
I'm very thankful to Dr. Ranjit Shaw, Principal Project
Geoscientist at Jason - A CGG Company and all the
members of JASON office at MIDC, Navi Mumbai for
providing me the assistance and guidance without which
this would not have been possible.

References

Figure 12 Inverted impedance 120 degree phase wavelet Al-Chalabi, M., 1997, Parameter nonuniqueness in
velocity versus depth functions; Geophysics, 62, 970-979.
Connolly, P., 1999, Elastic impedance; The Leading Edge,
18(4), 438-452.

Hosken, J.W.J., 1988, Ricker wavelets in their various

guises; First Break, 6(1), 24-33.

Simm, R. and White, R.E., 2002, Phase, polarity and the

Figure 13 Inverted impedance 150 degree phase wavelet
interpreter’s wavelet; First Break, 20(5), 277-281.

Walden, A.T. and White, R.E., 1998, Seismic wavelet

estimation: a frequency domain solution to a geophysical
noisy input-output problem; IEEE Transactions on
Geoscience and Remote Sensing 36, 287-297. White, R.E.,
1997, The accuracy of well ties: practical procedures and
examples; Expanded Abstract RC1.5, 67th SEG Meeting,
Figure 14 Inverted impedance 180 degree phase wavelet Dallas.

Observations

3
White, R.E., 1998, Stretch and squeeze – just keeping up
appearances? ; EAGE 60th Conference and Technical
Exhibition, Leipzig, Extended Abstract P138. White, R.E.
and Hu, T., 1998, How accurate can a well tie be? ; The
Leading Edge, 18(8), 1065-1071.