ANACOM

ANASAT®-PS
Protection Switch System
Operating Manual
You have just received an AnaSat®-Protection Switch System, a cost-effective product
with no compromise on quality or reliability. This product should provide tireless
performance in any reasonable operating environment.

We, at ANACOM, have taken great care to provide a convenient, easy-to-use product
in a small outdoor package. The Protection Switch consist of a Protection Controller
outdoor box, and WR-229 and WR-137 waveguide switches for C-Band applications,
or a pair of WR-75 waveguide switches for Ku-Band applications. Should a situation
arise beyond the operator’s control, just give us a telephone call. Many situations can
be diagnosed and solved by ANACOM’s trained customer-service personnel over the
phone.

If you have any questions, require technical assistance or training please call
ANACOM directly at (408) 519-2062 or FAX to us at (408) 519-2063. You can also
send e-mail to [email protected] and one of our engineers will contact
you.

ANACOM, INC.
1996 Lundy Ave.
San Jose, CA 95131
Tel: (408) 519-2062
Fax: (408) 519-2063
2013 AnaCom, Inc. All rights reserved. The information furnished by AnaCom, Incorporated, in this publication is
believed to be accurate and reliable. However, no responsibility is assumed by AnaCom for its use, nor any
infringements of patents or other rights of third parties resulting from its use. No license is granted by implication or
otherwise under any patent or patent right of AnaCom, Inc. AnaCom reserves the right to change circuitry and
specifications at any time without prior notice.
The following terms are trademarks of their respective holders:
AnaSat, AnaCom, Inc.
Polyswitch
Teflon
Duroid
VT52, VT100 Digital Equipment Corp.
INTELSAT
 ANACOM 3073906

Operating Manual
for the

ANASAT®-PS

Protection Switch System

Table of Contents
Subject Page
Section 1. Product Introduction and Specifications ............................................... 1-1
Typical Operating Parameters........................................................................................ 1-3

Section 2. Installation ................................................................................................. 2-1

Unpacking ............................................................................................................................. 2-1
Packing List ................................................................................................................... 2-1
Safety Precautions ......................................................................................................... 2-1
Site Considerations ........................................................................................................ 2-2
Protection Switch Mounting RF Considerations........................................................... 2-2
Protection Switch Mounting DC Considerations .......................................................... 2-2
Physical Mounting Considerations ................................................................................ 2-3
Cable and Waveguide Connections ............................................................................... 2-3
Water Resistance Wrap.................................................................................................. 2-5

Section 3. Operation ..................................................................................................3-1

Preliminary Steps................................................................................................................ 3-1
Manual Operation............................................................................................................... 3-1
M & C Operation.......................................................................................................... 3-2

ANACOM ANASAT®–Protection Switch iii

 ANACOM 3073906

Subject Page
Section 4. Theory of Operation............................................................................... 4-1
Switch Logic.................................................................................................................4-1
Receive Signal Switching ...................................................................................................4-1
Transmit Signal Switching..................................................................................................4-2
Switch Power Control.................................................................................................... 4-3
Monitor & Control......................................................................................................... 4-3

Section 5. Serial Port Operation............................................................................. 5-1

Software Applications Considerations .......................................................................... 5-1
RS-232 Data Terminal Connection ................................................................................ 5-2
RS-485 Data Terminal Single Connection ..................................................................... 5-2
RS-485 Data Terminal Multiple Connection .................................................................. 5-3
RS-485 Data Terminal Translator ......................................................................................5-4

Section 6. Maintenance ............................................................................................ 6-1

Built-In Test Equipment ...................................................................................................6-1
Controllable Functions from the Terminal ........................................................................6-1
Limited Warranty ......................................................................................................................... 6-1

Appendices
Appendix A. M & C Command Set ................................................................... A-1
Appendix B. Alarm List ....................................................................................... B-1
Appendix C. Connector Wiring .......................................................................... C-1
Appendix D. Drawings and Diagrams ............................................................... D-1

iv ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

Section 1. Introduction

This manual will normally refer to the TX/RX

Protection Switch version unless specifically noted.
Both units work exactly the same way.
The ANASAT®-PS VSAT protection unit inte-
grates all necessary functions, including complete
switch control logic, display indicators, microproces-
sor, and two independent serial ports into a single,
small outdoor package. Only the actual waveguide
relays are mounted separately. There is no need for
any indoor control box or power.
Figure 1-1 The ANASAT®-PS Protection Switch Designed to interface with any of the ANASAT
C or Ku VSAT transceivers, ELSAT block up con-
The ANASAT®-PS is a VSAT protection sys- verters, and ANASAT SSPA units, the Protection
tem designed for continuous outdoor duty in all types Switch can be used in a wide variety of communica-
of environments. Ideally suited for SCPC, MCPC, tion network situations where redundant radio equip-
and DAMA applications where high reliability re- ment is required.
quirements dictate the use of protected RF equip-
ment. The earth stations may be configured with the
optional Station Management System (SMS), tied to
The Protection Switch, TX Only (32314) pro- a PC, where you can monitor and control all local
vides complete 1 for 1 protection for TX only appli- transceivers and other network-compatible equip-
cations. Full TX and RX protection is provided with ment including the Protection Switch.
the model 30712. This works exactly the same way
as the TX Only unit, but includes an independent RX The ANASAT®-PS Protection Switch splits the
switch function as well. This means that both an RX modulator’s output to feed both A and B transceivers
and a TX fault (double fault) can occur at the same in parallel. This TX IF splitter function works for IF
time and the station can still operate normally. signals from 50 MHz through L band. For applica-
tions where the TX Only unit is protecting a pair of
SSPA amplifiers, an external microwave splitter
must be used to drive the two SSPA units.
The received IF signal from each transceiver is
fed to the Protection Switch where a high quality RF
relay is used to select either the A or the B trans-
ceiver. The selected signal is sent to the modem
equipment.
The transmit RF signal from each transceiver is
sent to a waveguide relay which can be a type-N,
WR-137, or WR-75. That relay is directly controlled
by the Protection Switch via a 6 conductor cable.
The relay is constantly monitored to insure that the
relay is locked to the selected transceiver. The TX
relay can be mounted in any convenient location. It
Figure 1-2 The ANASAT®-PS Protection Switch TX only

ANACOM ANASAT®–Protection Switch 1-1 Introduction

 ANACOM 3073906

is usually positioned to minimize waveguide (or coax)

lengths.
The receive RF signal from the antenna feed
system is switched to either transceiver A or trans-
ceiver B with an RX waveguide relay. This relay
can be either a WR-229 for C band, or a WR-75 for
Ku band operation. In order to minimize signal
losses, this relay is normally mounted directly on the
feed port. The relay switches the receive signal
from the antenna to either the A side LNC or the B
side LNC. Each LNC is then connected to its own
transceiver via coax cable. This arrangement pro-
vides the maximum amount of equipment protection
without loss of system performance.
The protection switch system can also be used
with a pair of LNBs in place of the LNCs. In this
case, the Protection Switch monitors the health of
the LNBs by measuring DC current consumption
but does NOT provide LNB power. That power
must come from the user through the TX IF cable
and it must be sufficient to power two LNBs.
The RX relay is controlled directly from the
Protection Switch unit via a 6 conductor cable. The
relay is constantly monitored to insure that the relay
is locked to the selected transceiver.
Power for the Protection Switch system comes
directly from both transceivers. No other power
source is needed. Even if one transceiver suffers a
power loss or is shut down externally, the remaining
transceiver can supply enough power to the Protec-
tion Switch for it to operate normally.
In the case where a TX/RX Protection Switch
system is used to interface with two ELSAT BUCs
and two LNBs, the LNBs are powered from the mo-
dem, via the Protection Switch Control box. There
must be sufficient power for both LNBs, or the sys-
tem may fail.

Introduction 1-2 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

Typical Operating Parameters

RF ELECTRICAL SPECIFICATIONS
A. TRANSMIT RF SWITCH
(1) Transmit RF Waveguide Relay Options
a) WR-137 C-Band
b) WR-75 Ku-
c) Type N Connection Option Band
CB d
(2) Maximum Power Level 1,000 Watts
(3) Switch Time 2 S maximum
(4) Off-line Load VSWR < 1.5:1
(5) Off-line Load Power Options for 20 through 1,000 Watts

B. TRANSMIT IF SPLITTER
(1) Connector Type Type N
(2) Frequency Range 50 to 2000 MHz
(3) Impedence 50 Ohms (75 Ohms optional)
(4) Insertion Loss 7 dB maximum
(5) Switch time 0 S (splitter)

C. RECEIVE RF SWITCH
(1) Receive RF Waveguide Relay Options
a) WR-229 C-Band
b) WR-75 Ku-
B d
(2) Switch Time 2 S maximum
(3) Off-line Load VSWR < 1.5:1

D. RECEIVE IF SWITCH
(1) Connector Type Type N
(2) Frequency Range 50 to 2000 MHz
(3) Impedence 50 Ohms (75 Ohms optional)
(4) Insertion Loss 1 dB maximum
(5) Switch Time 2 S maximum

ANACOM ANASAT®–Protection Switch 1-3 Introduction

 ANACOM 3073906

RF ELECTRICAL SPECIFICATIONS, (con’t.)

E. POWER REQUIREMENTS
(1) Voltage +13VDC
(2) Current, nominal 0.1
during switching Amps 5
A k
(3) Source Transceiver M&C connector

MECHANICAL SPECIFICATIONS
A. WEIGHT
(1) Protection Switch unit 3 lbs (1.8 kg) max.

(2) RF Relays
WR-229 waveguide switch 6 lbs (2.73 kg) max.
WR-137 waveguide switch 2.5 lbs (1.14 kg) max.
WR-75 waveguide switch 1.5 lbs (0.68 kg) max..
Type N switch (option) 1.10 lbs (0.49 kg) max.

B. SIZE
(1) Protection Switch unit 8.5” x 9.5” x 4.0”
(215.9 x 241.3 x 101.6 mm)
(2) RF Relays
WR-229 waveguide switch 3.45” x 3.45” x 7.73” (87.6 x 87.6 x 196.3 mm)
WR-137 waveguide switch 2.25” x 2.25” x 5.12” (57.2 x 57.2 x 130 mm)
WR-75 waveguide switch (option) 2.20” x 2.20” x 4.07” (55.8 x 55.8 x 103.4 mm)
Type N switch (option) 2.00” x 2.00” x 3.05” (50.8 x 50.8 x 77.5 mm)

C. SURFACE FINISH
Painted Surface

(a) Color (per FED-STD-595A, Spec. # 25630) Light Gray

(b) Final Coating: Powder

Unpainted Surfaces: Chem. Film per MIL-C-5541, Class 3

Introduction 1-4 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

ENVIRONMENTAL SPECIFICATIONS

A. AMBIENTTEMPERATURE CONDITIONS
(1) Operating –40 to +50°C

(2) Storage –60 to +75°C

B. ALTITUDE 15000'ASL max. (4560m)
C. RAIN 20" / hour (508mm/hr)
D. WIND 150 MPH (250km/hr)
E. VIBRATIO
N 1.0 G random
(1) Operating 2.5 G maximum random
F. (2) Surviva
l SHOCK 10G
(1) Operating 40 G max.

NOTE: Specifications subject to change without notice.

ANACOM ANASAT®–Protection Switch 1-5 Introduction

 ANACOM 3073906

Section 2. Installation
The ANASAT®-PS Protection Switch system ANASAT®-PS Packing List
consists of the Protection Switch box, one TX
Waveguide (or possibly coax) Relay, and one RX
 Protection Switch Box
Waveguide Relay as needed.
 TX Waveguide (or coax) Relay
This chapter contains the general requirements  RX Waveguide Relay
for installing the Protection Switch and associated  This Manual
Relays on the antenna and making the cable and  Quick Start Guide
waveguide connections. Specific mounting methods
may vary considerably depending upon particular an- Note: A cable kit containing several
tenna and site characteristics. Refer to the antenna possible cables may, or may not be
manufacturer’s instructions for more detailed instruc- included in this shipment.
tions.
ANASAT®-Protection Switch control box is
designed for installation and setup without removing
Table 2-1. ANASAT®-PS Packing List
the cover. The control box may be completely initial-
ized for normal operation using a Hand Held ASCII
terminal or a local computer. Safety Precautions
General
Removal of any cover may jeopardize
the weather seal which may cause Observe normal safety precautions
when operating this equipment.
! problems later.
!
Unpacking Ensure the Waveguide Relays and the Control
box are properly grounded. Do not rely on coaxial
Check to make sure that the Control box and cable shields for the ground connection.
the Waveguide Relays have not suffered any dam- If the cover is removed from any ANACOM
age in shipment. Compare contents of the crate to product, ensure that all:
ensure items received match those listed on the
packing slip. Retain all shipping containers for future  gaskets are intact and free of damage prior
use. to reinstallation
 mounting screws are properly installed
Tools and Test Equipment
Have on-hand a standard electrician’s tool kit Ensure all connectors are waterproofed.
and any tools listed in your antenna installation in-
structions. Power Supply
Power is obtained from the associated RF
equipment. No additional power is required. Al-
though the power feed from each transceiver is pro-
tected with a re-settable fuse, do not intentionally
short the power pins. Arcing may occur.

ANACOM ANASAT®–Protection Switch 2-1 Installation

 ANACOM 3073906

mounting kit, customized for your site and hardware.

Transceiver
Take adequate precautions to ensure the Contact ANACOM for details.
ANASAT® transceiver does not transmit a signal un-
til it has been properly connected and set up for au- Antenna
thorized frequencies and power levels. The Protection Switch components must be at-
tached to some form of mounting structure which is
Transmitter RF output power levels usually the antenna feed boom or the antenna mast.
are adequate to cause blindness or Specific mounting procedures will depend on the an-
other serious injury to body tissues. tenna used. The RF equipment is designed to be
! Use caution when working around the mounted on most antennas. Locate and install the
transceiver or antenna when the antenna according to the antenna manufacturer’s
transmitter is active. instructions. Specific mounting kits are available for
most antennas. Contact the antenna maker or
Power Amplifier AnaCom Inc.
Be sure the transceiver TX OUT port is prop-
Lightning arrestors should be used at the site to
erly terminated prior to operation. NEVER operate
protect personnel and equipment. Size 3/0 or 4/0
the transceivers when installing or working on the
stranded copper wire should be used to bond the
TX Relay.
transceiver to the antenna frame and to the lightning
Ensure all the correct waveguide gaskets are protection ground rod.
used to prevent water damage not only at the trans-
ceivers, but also on all ports of the TX Relay.
Protection Switch Mounting
TO ENSURE PROTECTION OF PERSONNEL
AND EQUIPMENT, USE CARE DURING AN- RF Considerations
TENNA INSTALLATION AND WHENEVER The ANASAT® PS Control box can be
WORKING ON OR AROUND THE SYSTEM. mounted in any position. However, for ease of use,
the front panel should be in a position where the dis-
LNC play is easily read and operated.
Be sure the LNC units are properly terminated
The length (and associated RF losses) of the
prior to operation. Ensure all the correct waveguide
interconnecting RF cables must be considered when
gaskets are used to prevent water damage on all
determining the location of the transceivers and both
ports of the RX Relay.
the TX and RX relays.

LNB The two LNCs should be mounted directly on

The use of LNBs in the Protection Switch sys- the RX relay. The RX relay itself should be mounted
tem is very similar to the use of LNCs. The main dif- directly on the RX feed of the antenna. This will
ference is that the LNBs connect directly to the minimize RF losses in the receive path and assure
RXIF connectors on the Protection Switch Control optimum receiver performance.
box. Unless specifically noted, assume that any other Each LNC is connected to its own transceiver
mention of LNCs will similarly apply to LNBs as with the 10 ft. (3m) coax cable provided with the
well. transceiver. If longer cables are required, low loss
coax must be used. As a rule of thumb, the LNC
Site Considerations cable must have less than 5dB total loss at 5GHz.
(LNB and BUC only) As LNBs are indepen-
Peculiar installation requirements of any par-
dent, there will be no cable connecting the LNB and
ticular site is the responsibility of the system opera-
the BUC.
tor. ANACOM can engineer an optional installation

Installation 2-2 ANACOM ANASAT®–Protection Switch

 ANACOM
The TX relay should be located near the two
3073906

protected transceivers (or power amplifiers). This

Physical Mounting
will minimize cable/waveguide cost. Over all TX Considerations
loss must be considered from a system engineering
view point. When mounting the transceivers and the Pro-
tection Switch components, allow enough room to
adjust the antenna’s azimuth and elevation. Through-
Protection Switch Mounting out installation and during any polarization, azimuth,
DC Considerations or elevation adjustment, ensure the cables and
waveguide are not crimped or pinched.
Positioning of the Control box should be within
The Control box has the same mounting holes
a few feet of the RX relay. Both relays require 12
as the AnaCom transceivers: 1/2 inch holes sepa-
volts DC to operate. The RX relay uses several
rated by 5 inches. Since the Control box is small and
amps of current when switching. Therefore, voltage
light, the box can be mounted on the very same
drop in the relay control cable is an important
mounts as one of the transceivers, using the same, or
consideration. The RX control cable should be as
similar, mounting hardware.
short as possible to maintain proper switching volt-
ages. If the cable is constructed with small gauge
wires, the RX relay may not switch reliably. LNC/TR Filter Mounting
A Transmit Reject (T/R) filter, the two LNCs,
AnaCom recommends the distance between and the RX relay are shown in Figure 2-1. Bolt this
the RX relay and the Control box be 10 ft. (3 meters) assembly to the antenna’s feed horn at the T/R filter
or less and that the RX relay control cable be con- open end. In this way, only one T/R filter is needed.
structed with 18 AWG wires. If the distance must
be greater, then heavier wiring must be used. WARNING! TX power should never be ap-
plied to the antenna without an adequate T/R fil-
The TX relay is also a 12 VDC unit but re- ter installed to protect the LNCs.
quires less current than the RX relay. The distance
between the TX relay and the Control box should be Route the two LNC cables to the transceivers,
15 ft. (5 meters) or less and the control cable should and the RX relay control cable to the Control box.
also be constructed with 18 AWG wires.
Additional voltage drop must also be considered OMT receive port CPR-
for the cables between the transceivers and the Con- 229G
trol box. The 12 volts used by the TX and RX relays
control cable

is generated by the transceivers themselves. There

RX switch
T/R FILTER

is no power supply in the Protection Switch itself.

TO ODU B

Cabling between the transceivers and the Control TO ODU A

TYPE N

TYPE N

box must assume that all power comes from only one
of the transceivers. Therefore, these cables must be
kept as short as practically possible. AnaCom rec-
ommends a cable length of 10 ft. (3m) or less.
AnaCom further recommends that the +12 VDC
wire (pin 7), and the ground wire (pin 18) both be
made from 18 AWG wire or heavier. LNC B LNC A

The heavy gauge power wiring discussed in this

section can be achieved by paralleling multiple Manual Over-ride
smaller wires in the cable as necessary.
LOAD

Figure 2-1 RX Switch, C band example

ANACOM ANASAT®–Protection Switch 2-3 Installation

 ANACOM 3073906

Cable and Waveguide (0dBm Transceivers) Connect sections of low

loss coaxial cable with Type N connectors be-
Connections tween the Power Amplifier input port, and the
transceiver’s transmit output (TX OUT). Then
Cabling Requirements use waveguide to connect between the Power
Local regulations may require that cables in oc- Amplifier outputs, the TX waveguide relay, and
cupied buildings be installed in steel conduit. Local the antenna TX port as described above for
government agencies may waive this requirement for Waveguide TXOUT. Ensure all connections
the use of Plenum cables, which are standard cables are weather-tight.
entirely encased in solid Teflon. Check the codes in
Connect a control cable between the TX
your area.
waveguide relay (circular connector) and the
NOTE: Equipment outages due to faulty Protection Switch 6 pin connector labeled TX
cable materials or installation are not covered by RELAY.
your warranty.
The cables needed for interconnecting the
ANASAT®- Protection Switch to other equipment 2. 70 MHz Modem
(including other AnaCom equipment) are not neces- (TX side) Attach a coaxial cable with N-con-
sarily included. Various external equipment and con- nectors between the Protection Switch TX IF
figurations are too widely varied to be able to antici- connector (see Figure 2-3) and the modulator
pate all possibilities. Specific installations can be ad- IF OUTPUT. Make sure that the connec-
dressed with special AnaCom Cable Kits. Contact tions are weather-tight.
AnaCom for details.
Attach another coax cable with N connectors
1. Transmitter Feed between transceiver “A” TX IF input connector,
and the Protection Switch (Control box) con-
(Waveguide TX OUT) Connect a section of
nector labeled TX IF A. In a similar fashion,
flexible waveguide between the TX Relay com-
connect another coax cable from transceiver
mon port and the antenna OMT transmit port.
“B” TX IF input to the Control box at TX IF B.
Waveguide should be attached to the antenna
The internal connection inside the Control box is
feed per manufacturer’s instructions. Use an-
a resistive splitter with DC blocking.
other section of waveguide to connect each of
the transceiver’s transmit output, (TX OUT) to (RX side) Attach a coaxial cable with N con-
the A and B ports of the TX Relay. Ensure a nectors between the Protection Switch RX IF
gasket is fitted for each port. (see Figure 1-3) and the demodulator IF IN-
PUT. Make sure that the connections are
(Type N TXOUT) Connect low loss coaxial weather-tight.
cable with type N connectors between the
OMT transmit port, the TX Relay (with Type N (If the system uses BUCs instead of trans-
connectors) and the transceiver’s transmit out- ceivers, skip this step) Attach another coax
put, in the same configuration as described cable with N connectors between transceiver
above for waveguide. Ensure the connec- “A” at the RX IF output connector, and the Pro-
tions are weather-tight. tection Switch (Control box) connector labeled
RX IF A. In a similar fashion, connect another
(0dBm Transceivers) If there are no external coax cable from transceiver “B” RX IF con-
power amplifiers in the system (they may be nector to the Control box at RX IF B. The in-
separately protected), then install coaxial cabling ternal connection inside the Control box is a re-
as described above for the Type N transceivers. lay. Make sure all IF connections are
weather-tight!

Installation 2-4 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

3. LNC TX Baseball Radio

Switch Transmit
Attach both “A” and “B” LNCs to the RX Port 1 Wave Guide to Feed
waveguide relay. Attach a high quality T/R fil- Port 2 Wave Guide Radio-A
ter to the RX waveguide relay common port. Port 3 TX-Termination (large)
See figure 2-1. Bolt this entire assembly to the Port 4 Wave Guide Radio-B
antenna RX feed point. Make sure all ports RX Baseball Radio
have waveguide gaskets installed! Switch Receive
Port 1 RX Feed
Attach the RF cable supplied with the transceiv-
Port 2 LNC connected to Radio-A
ers between the LNC type N connector and the Port 3 RX-Termination (small)
transceiver connector labeled “LNC”. If a Port 4 LNC connected to Radio-B
longer cable is required, insure that the replace-
ment cable is a low loss microwave type. Make (LNB and BUC only)
sure that the LNC attached to the “A” port of RX Baseball Radio
the RX relay is connected to the “A” trans- Switch Receive
ceiver. Port 1 RX Feed
Port 2 LNB-A
Accidental cross-connection of RX cables Port 3 RX-Termination (small)
can result in NO receive signals at the mo- Port 4 LNB-B
dem regardless of switch position!
Connect a control cable between the RX
waveguide relay (circular connector) and the
Protection Switch 6 pin connector labeled RX
Final Check
Recheck all bolts and cabling. Refer to Ap-
RELAY.
pendix D to verify cable connections.
(LNB and BUC only) LNB attachment to the
RX waveguide relay is the same as the above Water Resistance Wrap
method for the LNCs. The application of moisture-resistant wrap
Attach the RF cables from the LNB type N (mastic tape) to all connectors is required to prevent
connector to the corresponding RXIF connector water entry and resultant water damage. Apply the
on the Protection Switch Control box. Make mastic tape as follows:
sure all IF connections are weather-tight! 1. Ensure that all connectors are tight and “O”
rings are installed in plastic cable connectors.
4. Terminal Connections
2. Pre-cut the mastic tape or 3M type 2242
A data terminal or a computer with terminal
tape to the desired size. Each connector
software connects to the ANASAT®-Protection
should be fitted with one piece of tape, not
Switch via either RS-232 or RS-485 serial ports
several short pieces.
at the 18-pin circular connector labeled
“M&C”. Appendix C shows the pin-out of the 3. Center the tape on the connector to be
serial outputs. See chapter 5 for a discussion of sealed and wrap the tape tightly around the
serial port configurations. Optional serial com- connector. Squeeze the tape tightly and en-
puter cables are available from ANACOM. sure that both ends of the tape have formed
around the connector and the cable.
5. Baseball switches 4. Apply the mastic tape to all connectors that
The connectivity of cables and Wave-Gudes to may be exposed to moisture.
the baseball switches can only be done in one
possible way. See opposite tables: (see figure 2-2 on next page)

ANACOM ANASAT®–Protection Switch 2-5 Installation

 ANACOM 3073906

Figure 2-2 Example of a properly weatherized

connection

Installation 2-6 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

Section 3. Operation
and properly terminated. Improper termination can
Preliminary Steps cause severe damage to amplifier components.
After all of the ANACOM®-PS hardware Open or leaking transmission
is mounted and verified, the antenna must be lines anywhere between the
aimed toward the desired satellite. Follow the power amplifiers, theTX relay,
antenna manufacturer’s instructions, using coor- and the antenna feed can
dinates provided by the satellite operator. ! cause personnel injury or
Do not transmit until you even death.
have received authoriza-
tion from the satellite net- Manual Operation
! work operation center, and
a transmit power level from The Protection Switch operation is very simple.
its engineering staff. There are five (5) push-button switches on the front
panel which are used to manually set operating con-
Both the on-line and the standby transceiv-
ditions of the Protection Switch. See Figure 3-1.
ers must be set up for the same TX frequency,
RX frequency, TX gain, and RX gain values. Four red lights show active alarms from the
transceivers. These lights are based on relay contact
Refer to the AnaSat Series Transceiver
closures in the radio equipment. If separate high
Operation Manual for details.
power amplifiers are used, their alarm relay contacts
Which transceiver is designated “A” and should be wired in parallel with the transceiver TX
which is “B” is arbitrary. However, once you alarm relay. Then an alarm in either the power am-
decide, the installation wiring, programming and plifier or the TX side of the transceiver will cause the
operation of the system must be consistent. red light to glow.
Before applying power to either transmitter, Four green lights show the present state of the
make sure that the transmit signal path is secure TX and the RX relays. There should be one TX and
one RX light active at any given time. If the light is
ANA COM Protection flashing, this indicates the relay is in Over-Ride mode
AUTO Switch and will not switch if a fault occurs.
If both A and B green lights are on for either
TX - A TX - B the TX or RX relay, this means the Protection Switch
ON-LINE cannot determine the state of the physical relay.
ALARM
This can happen if the cable to the relay is discon-
nected.
RX - A RX - B One red light is used to indicate a SWITCH
ON-LINE
FAULT. This is usually caused by a faulted TX or
RX relay, a cable fault, or may be due to an internal
ALARM
microprocessor fault.

SWITCH FAULT
AUTO Operation
By pushing the AUTO switch, the Protection
Figure 3-1 TX/RX Switch Panel Layout Switch is put into AUTOmatic mode for both TX and

ANACOM ANASAT®–Protection Switch 3-1 Operation

 ANACOM
RX. In Auto mode, the individual TX and RX relays Since TX and RX switches are independent,
3073906

will switch to the transceiver not having alarms. one can be in AUTO mode while the other has an
over-ride active.
If neither transceiver has an alarm (the normal
situation), then the Protection Switch takes no action.
However, should one of the on-line transceivers gen- M & C Operation
erate an alarm, then the Protection Switch will re-
move the faulted unit from service and switch the
Terminal Display
stand-by unit on-line.
Connect a terminal (or computer running termi-
AUTO mode is visually verified by noting the nal emulation software, switch.exe or Hyper termi-
green ON-LINE LED is steady, not flashing. nal) to the RS-232 serial port. Set the terminal to
1200 baud, eight data bits, no parity, and one stop bit
Note that TX and RX sides of the transceiver
(1200,N,8,1 protocol). Refer to Appendix C for wir-
are independent. It may be normal, for example, for
ing diagrams for the COM ports.
the A side TX to be on -line while the B side RX is
on-line. The M & C terminal display gives a complete
accounting of the Protection Switch alarms and sta-
Manual Over-ride Operation tus. The display is usually sent to the terminal every
By pushing one of the other four push button 30 seconds. This interval can be changed with the
switches, the Protection Switch will force the select- UTIMER command. (See Appendix A).
ed equipment to go on-line. Figure 3-1 shows what this status screen looks
For example, by pushing the TX A switch, the A like.
side transmitter will be switched on-line regardless of The top line shows the Protection Switch user
its alarm state. The Protection Switch will keep the label, hardware revision, and serial number.
A transmitter on-line until the AUTO switch is
pushed, or until the TX B switch is pushed. The second line shows any alarms which may
be active at the time. This includes summarized
Manual Over-ride mode is indicated by the transceiver alarms in addition to actual Protection
flashing green LED on the front panel. Switch alarms (see Appendix B).
Note that the switch is a “non-revertive” type. The third line shows the present setting of the
This means that when a momentary alarm causes a TX switch and if the switch is in AUTOMATIC or
switch action, the removal of the alarm does not MANUAL over-ride mode.
cause the switch to go back to the former equipment.
The fourth line shows the present setting of the
If a switch is forced using one of the push-but- RX switch and if the switch is in AUTOMATIC or
ton switches, the switch will not switch back again MANUAL over-ride mode.
when the AUTO button is pushed (unless there is an
alarm active). The fifth line gives details about the serial port
and how the port is presently set:

{USER LABEL} AnaCom VSAT PROTECTION SWITCH REV:02 S/N:123456

ALARMS: CLEAR
TX A on line | TX RELAY in MANUAL MODE
RX B on line | RX RELAY in AUTOMATIC MODE
DTE1: PC_MODE |UTIMER: 30.0 |TERMTYPE: TTY |ECHO on|CRLF off|BAUDRATE
19200 COMMAND>_

Figure 3-2. Remote M & C terminal screen display.

Operation 3-2 ANACOM ANASAT®–Protection Switch

 ANACOM
 DTE1 is the RS-232 port (DTE0 is the RS-
3073906

This command switches the RX relay to the A

485 port). The port operating mode can be PC- side regardless of alarm status. This also puts the
MODE if you are using an ASCII terminal, or RX switch into manual over-ride mode.
PACKET if you are using terminal software which
uses packet protocol.
 RXB
 UTIMER is the screen refresh time. This
This command switches the RX relay to the B
can be set to any number of seconds (usually 30), or
side regardless of alarm status. This also puts the
be turned OFF.
RX switch into manual over-ride mode.
 ECHO gives the present setting for the ter-
minal echo function. When “ON”, the serial port will Extended M & C Commands
echo all characters typed. When this parameter is Several other commands are available for use
“OFF” then the port will not echo characters. in setting the serial ports or setting other user param-
 CRLF gives the present setting for the serial eters. Appendix A gives a complete list of all M&C
port to issue a line feed (LF) after each carriage re- user commands.
turn (CR). Options are “ON” or “OFF”.
 BAUDRATE shows the present terminal com-
Hand-Held Terminal
munications speed setting in bits per second (bps). The AnaSat Hand-Held Terminal can be used
Note that in order to change baudrate, first give the to control and monitor a 1+1 Redundancy System.
Protection Switch a command to change rate, then Please see the Section “Controlling 1+1 Redundant
change baudrate on your terminal. Systems” in the AnaSat Hand-Held Terminal Guide.

Basic M & C Commands

There are five basic Protection Switch com-
mands. Their operation is exactly the same as press-
ing the front panel push-button switches.

 AUTO
This command puts the Protection Switch into
AUTOMATIC mode for both TX and RX switches.

 TXA
This command switches the TX relay to the A
side regardless of alarm status. This also puts the
TX switch into manual over-ride mode.

 TXB
This command switches the TX relay to the B
side regardless of alarm status. This also puts the
TX switch into manual over-ride mode.

 RXA

ANACOM ANASAT®–Protection Switch 3-3 Operation

 ANACOM 3073906

Section 4. Theory of Operation

General Receive Signal Switching

The ANASAT®-Protection Switch consists of Receive signals from the antenna feed through
only two major blocks: a waveguide port into the TR Filter, which prevents
the transmit signal and receiver image frequencies
• Switch Logic and Control from passing into the low noise block converter
• Communications M & C (LNC).
The T/R filter is necessary to insure that the
Switch Logic earth station TX signals do not overload the sensitive
RX low noise amplifiers, and to protect against image
The Switch Logic circuits monitor alarm relay signals. Some antenna manufacturers include the T/
states of both A and B transceivers, both TX and RX R filter in their feed assembly. If not, a suitable T/R
relays, and the five front panel push-buttons. filter is available from ANACOM.
A latch circuit (one bit memory cell) maintains The LNC amplifies and mixes the receive sig-
the state of each switch (TX and RX). This latch nal, outputting a IF signal to the converter module.
can be set or reset from several inputs:
See the Signal Flow Block Diagram in the Ap-
Front panel manual over-ride switch is pushed pendix D.
M&C computer commands The coaxial cable connecting the LNC with the
transceiver carries not only the IF signal, but also a
Transceiver alarm
stable LO signal from the transceiver to the LNC,
If the latch is set (or reset) by an over-ride ac- plus +13 VDC power for the LNC.
tion from either the push-button switches or from the
Any attempt to monitor the
M&C computer, any change of alarm state is ignored
LO signal in the LNC cable
until the over-ride state is reset by the AUTO func-
may severely damage your
tion. test equipment due to the DC
Both TX and RX relays are monitored to insure ! supply voltage.
they are switched to the proper side. This is accom- Use a DC block!
plished by monitoring secondary switch closures in Since the LNC is not a typical TVRO device,
the relay itself. Should any relay NOT be in the and since it is calibrated in gain in conjunction with its
proper position, a SWITCH ALARM is set. own transceiver, it is not possible to use a single
The SWITCH FAULT is set whenever any of LNC and switch at the L band cable.
the three relays (TX, RX waveguide, and RX IF) are Always insure that the A side LNC is con-
not in the proper position, or when any of the relays nected to the A side transceiver, and that the B side
are disconnected from the Protection Switch. When LNC is connected to the B side transceiver.
the alarm is active, the front panel red light will
blink, and a dry contact closure is provided at the Check the serial numbers of the LNCs to see
18 pin M&C connector. See Appendix C. that they match their respective transceivers.
If used, LNBs are monitored by the Protection
Switch Control unit via their DC current consump-
tion.

ANACOM ANASAT®–Protection Switch 4-4 Theory of Operation

 ANACOM
If the LNCs are inadvertently reversed, the in-
3073906

of the switch latch, then a Switch Alarm is set. This

dividual transceiver gain value will not be correct, alarm can be seen on the front panel as a flashing
although the system may still function. red light, and the Protection Switch alarm relay is set
into alarm mode. (See Appendix C)
The RX alarm relay from the transceiver
should be normally closed, and open only during an
active alarm. This is important so that if a power Transmit Signal Switching
failure occurs in the ODU, the alarm relay will de-
fault to the alarm state.
Transmit IF Signal
An active alarm input to the Protection Switch The TX IF signal from the modem equipment is
will SET the RX switch latch if the alarm is from the split inside the Protection Switch and fed equally to
A ODU, and will RESET the latch if the alarm is the A and B transmitters.
from the B ODU.
This splitter is resistive and matched for 50
The RX latch state drives the RX waveguide Ohms. If either transceiver be removed from ser-
relay via high current drivers inside the Protection vice (physically), the TX IF connector on the Protec-
Switch box. tion Switch should be terminated in 50 Ohms. The
splitter gives a flat 6 dB loss of signal strength which
The RX latch SET and RESET will only occur
must be accounted for in the over all earth station
if the switch is in AUTO mode. If the switch is in
signal path calculations.
manual over-ride mode, any alarm input will be ig-
nored. This splitter is not rated at C or Ku band fre-
quencies. For SSPA protection, which requires split-
A manual over-ride can be set from the front
ting microwave frequency signals, use an external
panel push-button switches, or from the M&C com-
splitter.
puter. The over-ride command will SET or RESET
the latch immediately and block any alarm inputs.
Transmit RF Switch
The RX waveguide relay itself is a latching There are several possibilities of transmit equip-
type relay and will not change state unless com- ment and switching arrangments. The simplest ex-
manded to do so. Loss of power will not change its ample would be a pair of AnaSat-20EC transceivers.
state. A more complicated example would be a pair of
AnaSat-0EC transceivers working with a pair of high
Receive IF Switching power amplifiers (HPAs). The HPAs may be sepa-
Both transceivers are always on and opera- rately protected using a second Protection Switch, or
tional. However, only the “on-line” transceiver may be combined with the AnaSat-0EC as a single
(ODU) is actually processing a real signal from the TX entity.
antenna. Since the “off-line” transceiver has its
The operation of the Protection Switch is the
LNC terminated by the RX relay, its IF output signal
same for any TX equipment posibility. The Protec-
will be only the LNC noise floor.
tion Switch has one monitor point for the A transmit-
The Protection Switch contains a UHF type ter and one monitor point for the B transmitter.
latching relay which is used to switch between A and
In the case of the AnaSat-20EC example, the
B receiver outputs. Again, insure that the RX IF ca-
TX summary alarm relay in the transceiver is wired
bling is consistent with the RF side positioning of the
to the “ODU-A M&C” connector on the Protection
LNCs on the RX relay and cabling of the LNCs to
Switch box.
the correct transceiver.
In the case of the AnaSat-0 dBm unit plus
Position confirmation contacts within the RX
HPA, the HPA alarms must be wired to the 0 dBm
waveguide relay and in the RX IF relay are read by
unit with a separate cable. The 0 dBm unit then sum-
the Protection Switch logic. If the confirmation con-
marizes the HPA alarm with its’ own alarms to pro-
tact closures from both relays do not match the state
vide a single TX alarm for the protection switch.

Theory of Operation 4-2 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

The alarm relay(s) should be normally closed, Monitor and Control

and open only during an active alarm. This is impor-
tant so that if a power failure occurs in the ODU, the The monitor and control unit (M & C), is a mi-
alarm relay will default to the alarm state. croprocessor-based circuit providing remote diagnos-
tics and command capability.
An active alarm input to the Protection Switch
will SET the switch latch if the alarm is from the A Microprocessor-Based Functions
ODU, and will RESET the latch if the alarm is from
The heart of the M & C unit is the 80C188 mi-
the B ODU.
croprocessor, operating at 8 MHz. It has 128K of
The latch state drives the RF relay via high cur- SRAM and two 1MB FLASH EPROMs (electrically
rent drivers inside the Protection Switch box. erasable programmable read-only memories) for pro-
gram and variable storage.
The latch SET and RESET will only occur if
the switch is in AUTO mode. If the switch is in The microprocessor allows long term, com-
manual over-ride mode, any alarm input will be ig- pletely unattended remote operation of the ANASAT®-
nored. Protection Switch. All functions are ac- cessible
remotely via either of the two serial ports, which allow
A manual over-ride can be set from the front remote monitoring and diagnostics.
panel push-button switches, or from the M&C com-
puter. The over-ride command will SET or RESET
the latch immediately and block any alarm inputs. Serial Ports
Serial communication is provided through the
The TX relay itself is a latching type relay and SWITCH M&C. It is both RS-232 and RS-485
will not change state unless commanded to do so. compatible.
Loss of power will not change its state.
Both ports are completely independent and al-
Position confirmation contacts within the relay low communications rates between 300bps and
are read by the Protection Switch logic. If the con- 57.6kbps
firmation contact closure does not match the state of
the switch latch, then a SWITCH FAULT is set. Protocol is fixed at eight data bits, no parity, and
This alarm can be seen on the front panel as a flash- one stop bit. It is set at the factory to 1200bps.
ing red light, and the Protection Switch alarm relay is See applications examples in Section 5.
set into alarm mode. (See Appendix C)
Both ports can be used with a simple “dumb
terminal” or PC based terminal program such as
Switch Power Control “DT” provided by AnaCom.
All power for the Protection Switch comes Both ports can also be used in packet mode us-
from the AnaSat transceiver directly. The trans- ing the AnaCom packet protocol system.
ceiver 18 pin M&C connector has a source of +13
Volts DC. This is protected from accidental shorts Monitor Inputs
with a chemical fuse. This novel fuse opens when
The microprocessor monitors the state of
excessive current is drawn from the transceiver, but
both the RX and the TX switch latches, and the
recovers automatically when the short is removed.
SWITCH FAULT.
An internal timer, independent of the micropro-
cessor circuit is used to insure that the TX and RX Control Outputs
relays do not activate at the same time. Having both The microprocessor controls:
relays active at the same time could cause the
chemical fuse to open resulting in total power loss to  TXA over-ride
the Protection Switch.  RXA over-ride

ANACOM ANASAT®–Protection Switch 4-3 Theory of Operation

 ANACOM
 TXB over-ride
3073906

resulting in a total power loss of the Protection

 RXB over-ride Switch. Removal of the extra load, and subsequent
re-application of power to the Protection Switch may
 AUTO result in unwanted TX and/or RX relay switching.
These outputs are connected to the switch logic The Protection Switch normally draws only a
in parallel with the front panel push-button switches. few milliampears of current. However, the RX and
Their activation via remote commands is exactly the TX relays draw up to 3 Amps each during a switch
same as pushing the panel switches. action. The Protection Switch circuit includes stor-
age capacitors which can smooth out the switching
Power Up and Reset functions current load so as not to overload the protection fuse
The microprocessor will automatically boot it- in the transceivers. In addition, a timer circuit in the
self at the time of initial power application. No user switch logic circuit is used to insure the TX and RX
action is needed. relays are never operated at exactly the same time.

It is highly unlikely that the microprocessor will

ever hang-up. However, should it ever become
necesary to re-start the processor, simply push all
five front panel switches at the same time. This will
initiate a re-boot of the processor. Note that this
may also change the position of the TX and/or the
RX relays.

Alarm Relay
A mechanical form C relay is used in the Pro-
tection Switch for external alarm indication.
The alarm relay has normally-closed contacts,
so it defaults to the alarm state when power is off.

Power Distribution
All power for the Protection Switch comes
from the AnaSat transceivers. Each transceiver has
a source of +13 Volts DC on its 18 pin M&C con-
nector.
Power is protected from accidental shorts with
a chemical fuse. This fuse opens when excessive
current is drawn from the transceiver, but recovers
automatically when the current drain is removed.
The transceiver also contains a steering diode
in its utility power output. The Protection Switch
simply connects the A and B power sources together
for its internal +12 volt supply.
The voltage is fed through another steering di-
ode and is available on the SWITCH M&C 18 pin
connector for use externally. The use of this voltage
should be limited to only a few milliamps at most.
Excessive current drawn from this utility output may
cause the protection fuses in the transceiver to open

Theory of Operation 4-4 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

Section 5. Serial Port Operation

The Protection Switch contains two indepen- Software Applications Con-
dent serial ports for remote monitoring and control
applications. Both ports are made available on the siderations
middle 18 pin weather-tight connector labeled
The Protection Switch is shipped with an
“SWITCH M&C”.
applications utility program called DT. This program
is a “Dumb Terminal” emulator that communicates
Port 0 is a dedicated RS-485 (or RS-422)
with the Protection Switch (or any AnaCom radio)
balanced interface. This port is made available as a
with a simple ASCII exchange.
4 wire interface. 2 wire bus applications can be
supported if the TX + is wired to RX + and TX - is
DT differs from other terminal programs in that
wired to RX -. Port 0 should be used when ever
it will automatically establish communications with
control cable lengths are expected to be greater than
the Protection Switch at 1200 baud, then change
50 meters, or when multiple devices are to be
baud rate to 19,200 for faster user operation.
connected together on a single M&C bus.
Any user application program should do a
Port 1 is a dedicated RS-232 interface. Op-
similar routine: First establish communications at
tional control pins are available if needed: DTR and
1200 baud by sending about 5 to 10 Carrage Returns.
DCD. These are normally used with an external
Regardless of how the Protection Switch port was
modem. Simple terminal connections usually require
previously configured, it will reset to 1200 baud under
only TXD, RXD, and GND. Port 1 should be used
this condition. Next, send the desired new baudrate
only when the distance to the terminal (or modem) is
to the Protection Switch with the command
less than about 50 meters.
BAUDRATE 19200 (for example)
For both ports, baud rates are supported from
300 to 57,600. There is no “auto-baud” detection.
However, when in terminal mode, the Protection The Protection Switch port will immediately change
Switch will detect a mis-match in baud rates and to 19,200 baud. IMPORTANT: The user program
reset the port to 1200 baud. This is very important. must now be switched to the matching rate WITH-
Any M&C application program should first establish OUT sending any characters (or the Protection
commumications with the Protection Switch at 1200 Switch may fall back to 1200 baud). Communica-
baud, and then change baud rate to the desired speed tions is now established at the desired rate.
(see Appendix A).

Assistance with controlling this unit via either

(or both) serial ports is available by calling AnaCom.

ANACOM ANASAT®–Protection Switch 5-1 Serial Ports

 ANACOM 3073906

RS485/RS232 Selection RS-232 Data Terminal

The Protection Switch does NOT require pin
Connection
12 of the 18-pin circular connector to be strapped to
ground for RS-485. Both the RS-232 port and the Use a serial cable with a connector on one end
RS-485 ports are always active. that matches your terminal equipment (either a
“dumb” terminal or a computer running terminal
However, AnaCom radios do sense Pin 12 for emulator or modem software). Connect the 18-pin
RS-485 activation. As a convienience, pin 12 is weathertight circular connector to the other end,
internally connected to pin 12 of both ODU-A and following Figure 5-1.
ODU-B connectors.

25 pin “D” 9 pin “D” SIGNAL 18 pin circular

7 5 GROUND 18
3 2 TX DATA 17
2 3 RX DATA 16
8 1 DCD 15
20 4 DTR 14

Note: Select either the 9 or 25 pin female “D” connector to match your particular data terminal.
Most terminals do not need the DTR, DSR, or DCD connections.
Figure 5-1. RS232 Serial Cable Connections. Computer or terminal connections.

RS-485 Data Terminal

Single Connection emulator or modem software). Connect the 18-pin
weathertight circular connector to the other end,
RS-485 is usually utilized when the data cable following Figure 5-2. Note that pin 12 on the 18-pin
needs to be longer than what RS-232 can support, or
connector should be left open.
when it is required to communicate with more than
one piece of equipment at a time. Always use
An alternative wiring arangement is to use a 2
shielded, twisted pair cable!
wire bus. In this case, the TX + signal can be
connected to the RX + signal in the connector shell.
There are several different ways to utilize the
Also connect the TX - signal to the RX - signal in the
RS-485 port. First is a simple, direct connection
connector shell as shown in Figure 5-3.
between the Protection Switch and the user com-
puter terminal. In this configuration, operation of the
Protection Switch is identical to that of the RS-232
connection.

Use a serial cable with a connector on one end

that matches your terminal equipment (either a
“dumb” terminal or a computer running terminal

Serial Ports 5-2 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

Terminal SIGNAL 18 pin circular

GND GROUND 18
no connect 485 enable 12
TX + RX DATA + 10
TX - RX DATA - 11
RX + TX DATA + 8
RX - TX DATA - 9

Figure 5-2. RS485 Serial Cable Connections (four wire).

Terminal SIGNAL 18 pin circular

GND GROUND 18
no connect 485 enable 12
+ DATA + 10 RX +
– DATA – 11 RX -
8 TX +
9 TX -

Figure 5-3. RS485 Serial Cable Connections (two wire).

Although not shown in the figures, a 120 Ohm However, the maximum length of the data cable
resistor should be wired across the + to - should be kept to less than 500 meters.
connection at each end of the cable on both data
wire pairs. IMPORTANT: Any multiple connection
system will ONLY work in data packet mode.
In the two wire case, a resistor should be added
to each end of the data pair. The ASCII interface normally associated with
RS-232 operation does NOT work with RS-485
multiple connections. Therefore, a simple dumb
RS-485 Data Terminal: terminal (or computer running DT or Procomm) will
not work either. Multiple connection RS-485 MUST
Multiple Connections use the packet protocol defined in Packet.txt.
RS-485 can be used to control / monitor several
different devices using one common data bus. AnaCom radios, as well as the Protection
Wiring for multiple devices is a simple extension of Switch unit normally have the RS-485 port in “packet
the single connection wiring shown above. mode” at power turn on. The port is automatically
switched to Terminal Mode (non-packet ASCII)
With multiple connections, the data cable is when several Carriage Returns are received. The
daisy-chained to as many devices as desired. De- port will also automatically switch to “packet mode”
vices can be separated by considerable distances. when a packet containing the STX character (ASCII
02) is received.

ANACOM ANASAT®–Protection Switch 5-3 Serial Ports

 ANACOM
Wiring for multi-connection RS485 is similar to supported by the Protection Switch. When wiring
3073906

Figures 5-2 and 5-3 except that the wiring is chained the cable, insure that the cable is one continuous line
from one device to the next until all devices are and does not have “stub” lines in the middle. This
connected. Both four wire and two wire cables are could cause reflections and unreliable operation.

RADIO 1 RADIO 2 RADIO 3

RX + RX - TX + TX - RX + RX - TX + TX - RX + RX - TX + TX -

COMPUTER

TX +
TX -
RX +
RX -

Figure 5-4 RS-485 wiring between a host computer and various devices

RS-485 Data Terminal: The specific application of using the Protection

Switch as a translator is given in figure 5-5. The
Translator host computer must communicate with packets, and
the Protection Switch must be set with “DIGIPEAT
AnaCom radios and the AnaCom Protection
ON”. See Appendix A.
Switch have two independent serial ports. One port
can be configured to run RS-485 while the other one
As with other RS-485 configurations, a 120
is always RS-232. It is possible to use an
Ohm termination resistor should be wired to the end
AnaCom unit to convert between RS-232 and RS-
of each twisted pair.
485.

RS-232 Protection RADIO A RADIO B

Switch
RX + RX - TX + TX - RX + RX - TX + TX - RX + RX - TX + TX -

RS-232

COMPUTER
TO
OTHER
DEVICES

Figure 5-5 RS-485 wiring using the Protection Switch as a translator

Serial Ports 5-4 ANACOM ANASAT®–Protection Switch

 ANACOM
The Protection Switch has special internal For standard RS-485 (figure 5-4), simply
3073906

wiring which makes this translator function especially connect the radio A 18 pin connector to the switch
easy. ODU-A connector with 1-for-1 wiring. Similarly,
connect the radio B 18 pin connector to the switch
Inside the Protection Switch, the RS-485 lines ODU-B connector with 1-for-1 wiring.
are connected directly to the ODU-A and to the
ODU-B RS-485 lines. This allows both transceivers When using the Protection Switch as a transla-
and the Protection Switch unit to be automatically tor, the radio-to-switch cabling must reverse TX and
wired in the multi-connection RS-485 mode without RX wiring. This is shown in Figure 5-5 and below in
special daisy-chained cabling. Figure 5-6.

The three 18 pin connectors on the Protection Note that pin 12 MUST be wired to ground (pin
Switch have pins 8, 9, 10, 11, and 12 internally wired 18) before the radios will operate in RS-485. The
across. Protection Switch will operate in RS-485 with or
without this strap.

RADIO A RADIO B

RX + RX - TX + TX - RX + RX - TX + TX -

ODU-A

ODU-B
M&C

RS-232

COMPUTER

RX TX RX + RX - TX + TX -
PORT 1 PORT 0

MICROPROCESSOR

Figure 5-6 Internal Wiring of the Protection Switch

ANACOM ANASAT®–Protection Switch 5-5 Serial Ports

 10945 WR-137 waveguide, C Band
10956 WR-75 waveguide, Ku Band
11706 Andrew PNR-HC/F1PNM-H C Band
TX OUT

ELSAT or SSPA

IN
TX IF
M&C
18 PIN

COAX
30641-003
31197-003
COAX / WAVEGUIDE
OMT

ANACOM ANASAT®­­–Protection Switch

TO MODEM * COAX
TX IF IN Type N Switch 10931

M&C A

TX IF A
EQUIPMENT
Protection WR137 Switch 10928 C Band
WR75 Switch 10955 Ku Band
ANACOM

31048-010RS-232 / M&C
Switch
M&C 32314 10946-250 C band
31199-010RS-485 / M&C COAX / WAVEGUIDE
10958-250 Ku band
TX - RELAY (customer provided)
TX CONTROL CABLE

5-6
M&C B
* TX input cable should be 100% shielded:

TX IF B
6 PIN 30933-005 NOTE: Use coax cables only
low loss (Customer provided)
with 20W and below.
Note: Normal TX IF internal splitter is for IF inputs.
For C band SSPA applications, use 32314-C

COAX
For Ku band SSPA applications use 32314-K

18 PIN

30641-003
31197-003
COAX / WAVEGUIDE

IN
TX OUT

TX IF
M&C 10945 WR-137 waveguide, C Band
ELSAT or SSPA 10956 WR-75 waveguide, Ku Band
11706 Andrew PNR-HC/F1PNM-H C Band

ANACOM 1 + 1 Redundancy Protection Switch Cabling Diagram

NOTE: Most popular configurations shown. (C Band , TX only )

Other configurations also available . (Ku Band , TX only ) ANACOM 32123 REV03
11/22/2013  
3073905

Serial Ports
 ANACOM 3073906

Section 6. Maintenance

Built In Test Equipment authorization number (RMA). If it is necessary to

return the product for repair, the customer is
To improve and simplify maintenance routines, responsible for paying the cost of shipping it to
an external terminal (or computer) can be connected AnaCom. AnaCom will pay the cost of shipping
to monitor a number of critical parameters without the product back to the customer when the repairs
use of additional test equipment. These include: are completed. All import duties, customs fees,
taxes of any kind, or any related fees are the sole
- Transceiver alarm status (TX, RX; A and B)
responsibility of the customer.
- Switch alarm and position status
Spare parts, repairs, or replacements are
warranted to be free from defects in material or
workmanship for ninety (90) days or the remainder
Controllable Functions From of the limited warranty period, whichever is longer.
The Terminal
There are no express or implied warranties
except as listed above. In no event shall AnaCom
- Force TX switch to the A or to the B side be liable for special, incidental, or consequential
damages arising from the use of this product, or
- Force RX switch to the A or to the B side
arising out of any breach of this warranty. All
- Restore AUTOmatic operation express and implied warranties, including the
warranties of merchantability and fitness for a
particular purpose, are limited to the applicable
warranty period set forth above. No employee or
LIMITED WARRANTY representative of AnaCom is authorized to modify
this warranty or AnaCom’s standard warranty for
If this product should fail due to defects in any product.
materials or workmanship, AnaCom, Inc., will, at its
sole option, repair or replace it with new or rebuilt Non-warranty repair service is available from
parts free of charge for a period of two (2) years AnaCom for a nominal charge. Non-warranty repair
from the date of shipment from the AnaCom service can be obtained by contacting AnaCom and
factory. This warranty covers only failures due to requesting a return authorization number (RMA), as
defects in materials and workmanship that occurs described above. The customer is responsible for
during the period of the warranty. It does not cover paying the cost of the shipping to and from
damage that occurs during shipment, failure caused AnaCom for any non-warranty repairs. Non-
by operation of the product outside the published warranty repair service will be available for any
electrical or environmental specifications, or AnaCom product for a minimum of five years from
malfunctions caused by misuse of the product. the date of its first shipment from AnaCom’s
Expendable components are not covered under this factory.
warranty.

In order for the customer to exercise their

rights to repairs under the warranty, the customer
must first contact AnaCom to obtain a repair

ANACOM ANASAT®–Protection Switch 6-1 Maintenance

 ANACOM 3073906

Appendix A. M & C Command Set

The Protection Switch will not respond to any command until a carriage return has been entered,
terminating the command input. Multiple commands may be entered before a carriage return, using “;” as a
delimiter. Example: TXA; RXA <cr> will set the transmit switch to A, and the receive switch to A.

If a command is not recognized, an error message is returned. For example, if “foo <cr>” is
entered, the following is returned:

??????? foo

Alphabetical Listing of M & C Commands

Command Page
ALARMS .............................................................................................................................. A-2
AUTO ................................................................................................................................... A-2
BAUDRATE ......................................................................................................................... A-2
CLEAR_PASSWORD ......................................................................................................... A-2
CLS ........................................................................................................................................ A-2
CRLF ..................................................................................................................................... A-2
DIGIPEAT ............................................................................................................................. A-2
DTE ....................................................................................................................................... A-3
ECHO .................................................................................................................................... A-3
HELP ..................................................................................................................................... A-3
LABEL .................................................................................................................................. A-3
LOCK PASSWORD ............................................................................................................. A-3
MODE ................................................................................................................................... A-3
MODEM_MODE ................................................................................................................. A-3
MODEM_STRING ............................................................................................................... A-4
PC_MODE ............................................................................................................................ A-4
RESET ................................................................................................................................... A-4
RXA . ..................................................................................................................................... A-4
RXB ....................................................................................................................................... A-4
SAVE ..................................................................................................................................... A-4
SET_PASSWORD ................................................................................................................ A-4
STANDBY_MODE .............................................................................................................. A-4
TERMTYPE ......................................................................................................................... A-5
TXA ....................................................................................................................................... A-5
TXB ....................................................................................................................................... A-5
UNLOCK PASSWORD ....................................................................................................... A-5
UTIMER ............................................................................................................................... A-5

ANACOM ANASAT®–Protection Switch A-1 Appendix A

 ANACOM 3073906

ANASAT®-Protection Switch
M & C Commands
ALARMS
This command returns a list of raised alarms for the Protection Switch. The possible
alarms are: RXA, RXB, TXA, TXB, SWITCH, and PROMERR.
If there are no alarms then “ALARMS CLEAR” is returned. Status of all individual
alarms is evaluated ten times a second.

ALARMS
RXA raised when the receive section of transceiver A gives an alarm.
RXB raised when the receive section of transceiver B gives an alarm.
TXA raised when the transmit section of transceiver A gives an alarm.
TXB raised when the transmit section of transceiver B gives an alarm.
SWITCH raised when either the TX or RX waveguide relay confirmation does
not match the desired switch state.
PROMERR raised if a write or erase operation in the PROM fails.

AUTO
This command sets the Protection Switch into AUTOmatic mode. The Protection
Switch is free to switch both TX and RX waveguide relays based on the alarm state of trans-
ceiver A and transceiver B.
BAUDRATE [ 300 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600]
This command sets the baudrate of the serial channel the user is presently connected to.
The serial port has been programmed for 8 bits, no parity and 1 stop bit. These parameters
are not changeable.
CLEAR_PASSWORD [PASSWORD]
This command will clear an existing password. Note that the password must be given in
order for it to be cleared.
CLS
In terminal mode, 25 line feeds are sent to the terminal, effectively clearing the screen.
CRLF [ON | OFF]
This command is only relevant to dumb-terminal mode. It sets (or returns) carriage-re-
turn/line-feed status. “CRLF ON” will command the M & C computer to insert a line-feed in
display output following a carriage return. This can be necessary to make some terminal dis-
plays operate properly. In other cases this would be redundant.
DIGIPEAT [ON | OFF]
In packet mode, packets received on one port are transmitted out of the other port. In
this manner, the Protection Switch acts as a bi-directional digital repeater.

Appendix A A-2 ANACOM ANASAT®–Protection Switch

 ANACOM
DTE [0 | 1] (COMMAND) (ARGUMENT)
3073906

This command gets [sets] specific parameters for a specific serial port. If the command
is left out, all port settings are returned. Port 0 is RS-485 and port 1 is RS-232. This com-
mand can be given from either port. Acceptable commands include: ECHO, CRLF,
BAUDRATE, TERMTYPE, PACKET_MODE, TERMINAL_MODE, UTIMER.
ECHO [ON | OFF]
This command is only relevant in dumb-terminal mode. It sets (or returns) character
echo mode. For example, if the operator is running a terminal emulation program on his PC
with local echo disabled, type
ECHO ON
to enable echo back from the M & C computer. If the terminal is displaying doubled up char-
acters, use ECHO OFF.
HELP
?
H
This command displays a menu of available commands for quick reference.
LABEL [TEXT]
This command erases or [sets] an alphanumeric string up to 32 characters long that the
user can use to “title” or describe the purpose of the given device. This label appears on ev-
ery status screen.
LOCK PASSWORD
With this command most M & C functions will be locked and further user access will be
denied until the UNLOCK command is given. Those commands which remain user accessible
are: UNLOCK, CLS, and ALARMS.
If a password has been established with the SET_PASSWORD command then that
password must be used with the LOCK command. If there is no established password (if
CLEAR_PASSWORD has been used, for instance), then M & C functions will be locked; but
they can be unlocked without a password. There is only one solution to the problem of hav-
ing a locked unit and/or a forgotten password:
If the unit is attached to a modem, and presently accessible remotely,
telephone ANACOM.
MODE
This command returns either MODEM_MODE or PC_MODE. Example: MODE
might return MODE MODEM_MODE when the user is connected to the unit via a phone line
and a Hayes compatible modem.
MODEM_MODE
This command is used to tell the M & C computer that a Hayes compatible modem is
attached (or is about to be attached) to the serial port. The way this would be used is a user
would enter this command from a PC using a null modem cable, then disconnect the PC and
attach a modem directly to the port via a modem cable. RX, TX, DCD and signal GND
lines must be properly connected.
Once MODEM_MODE is activated, the M & C computer will no longer display dumb
terminal display updates or generate packets in packet mode until the DATA-
CARRIER_DETECT line becomes active, indicating the modem is off-hook and connected to
another modem.

ANACOM ANASAT®–Protection Switch A-3 Appendix A

 ANACOM
MODEM_STRING [TEXT]
3073906

When the M & C computer is in modem mode it will periodically send a Hayes compat-
ible initialization string of up to 40 characters to the modem to make sure it is properly config-
ured. The user can get [set] this string via this command. The default string as part of fac-
tory settings is:
MODEM_STRING AT S0=1 &C1 &S0 \Q0 E0
PC_MODE
This is the converse of MODEM_MODE. At any time, the user may type PC_MODE
and the M & C computer will again behave as if a PC or network is directly attached to the
serial port rather than a modem.

RESET
This command resets the M & C computer. This should not normally cause the Protec-
tion Switch to change state.
RXA
This command forces the RX switch to the A side and into MANUAL mode. The RX
switch will remain on the A side regardless of any RX alarms. Use the AUTO command to
revert the RX switch to automatic operation.
RXB
This command forces the RX switch to the B side and into MANUAL mode. The RX
switch will remain on the B side regardless of any RX alarms. Use the AUTO command to
revert the RX switch to automatic operation.
SAVE
This command saves present M & C operating parameters to a FLASH EEPROM.
Note that the Protection Switch state of RX and TX relays is NOT saved. This is only used to
store serial port operating parameters.
SET_PASSWORD [PASSWORD] [PASSWORD]
The M & C computer supports password control of M & C functions. One potential
use of this feature would be for leaving the Protection Switch unit connected to a modem on
an open telephone line. A valid password must be an alphanumeric string with no imbedded
blanks, and between four and eight characters long inclusive. It must be given twice to ensure
accuracy.
An existing password must first be cleared before setting a new password. This is done
with the CLEAR_PASSWORD command.
STANDBY_MODE [HOT | WARM]
Conventionally, when a protection system has been set up, the unit in standby mode is in
a HOT standby mode. This means that the TX function is ON and the standby unit is trans-
mitting into a load through a baseball switch. Beginning with REV 11 of the protection switch
firmware, and REV 48 of the ODU firmware, this command can be used to select a WARM
standby mode instead. In this state, the transmitter will be muted and will not be transmitting
while in standby mode. The positive aspect of this feature is that the system will draw only
half the current, since the TX function in the standby ODU will be muted. The negative as-
pect is that the transmit function in the standby unit will not be monitored for alarms until it is
brought back online.

Appendix A A-4 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

Entering this command without an argument will return its present state. Use the SAVE
command to make the setting permanent.
Note: unplugging the control cable that runs from the protection switch to the ODU will
remove the mute control line being asserted by the protection switch, and the ODU will return
to full output power!
TERMTYPE [TTY | VT52 | VT100] (OLD UNITS,OBSOLETE)
This command is only relevant to dumb-terminal mode. It sets (or returns) the terminal
emulation mode.
TTY Terminal Mode: this is a basic 80 character by 25 line ASCII “dumb” terminal
mode.
VT52 Mode: This is a standard terminal emulation, more intelligent than TTY.
VT100 Mode: This in an enhanced communications terminal emulator with a fixed dis-
play window.
There are some control characters that will be filtered by the terminal driver when the
M & C computer is in terminal mode. These control characters will be ignored in packet
mode.

CTRL-E: This will erase the screen, similar to the CLS command.
CTRL-Q: refer to the description of CTRL-S.
CTRL-S: Periodic screen updates will be squelched until the user has
finished entering present command or hits CTRL-Q.
CTRL-BS: (Backspace) The present input command will be erased.
TXA
This command forces the TX switch to the A side and into MANUAL mode. The TX
switch will remain on the A side regardless of any TX alarms. Use the AUTO command to
revert the TX switch to automatic operation.

This command forces the TX switch to the A side and into MANUAL mode. The TX
switch will remain on the A side regardless of any TX alarms. Use the AUTO command to
revert the TX switch to automatic operation.
TXB
This command forces the TX switch to the B side and into MANUAL mode. The TX
switch will remain on the B side regardless of any TX alarms. Use the AUTO command to
revert the TX switch to automatic operation.

UNLOCK PASSWORD
This command will unlock M & C functions for user access.

UTIMER [NUMBER]
This command is only relevant to dumb-terminal mode. It sets (or returns) the number of
seconds between automatic display updates. Note that changing baud rate will automatically
revert to a default appropriate for that particular baudrate.

ANACOM ANASAT®–Protection Switch A-5 Appendix A

 ANACOM 3073906

Appendix B. Alarm List

The ANASAT-C Protection Switch provides a simple control and monitor feature. If an abnormal
condition occurs, a description of the abnormality is sent via the M & C serial port to the operator’s console.
Transceiver alarms are monitored and related via the serial port even though they are not Protection
Switch alarms per se. This is done so that a single point remote M&C computer can see transceiver summary
alarms as alarms even though only the Protection Switch unit is actually connected.
A true Protection Switch alarm is reported as simply a SWITCH alarm. This almost always means that
one of the waveguide relays has not switched to the proper side. It could also mean that the internal RX IF
relay has not switched properly.

ALARMS
TXA there is a summary TX fault on the A transceiver
TXB there is a summary TX fault on the B transceiver
RXA there is a summary RX fault on the A transceiver
RXB there is a summary RX fault on the B transceiver
PROMERR the M & C PROM checksum fails
SWITCH one of the waveguide relays or the RX IF relay has not switched
properly

ANACOM ANASAT®–Protection Switch B-1 Appendix B

 ANACOM 3073906

Appendix C. Connector Wiring

6-Pin Circular Weathertight Connectors

5 1
1 6
4 5 6 2
2 4
3 3

Cable Wire View Cable End View

Pin Signal Description

1 P12V + 12 VDC
2 A A side relay coil
3 B B side relay coil
4 ACON A side confirmation
5 GND Ground
6 BCON B side confirmation
Note dimple next to pin 1
18-Pin Circular Weathertight Connector: M&C

1
10 1112 1 11
2 12
9 17 18 13 2 3 13 17 10
18 9
16 14
8 15 3 14 16
4 15
7 4 8
6 5
5 6 7

Cable End View Cable Wire View

Pin Signal Description Pin Signal Description

1 RYNO Alarm Normally Open 10 RX+ Differential Receive Data
2 RYNC Alarm Normally Closed 11 RX- Differential Receive Data
3 RYC Alarm Common 12 RS485 RS485 Jumper (open for 232)
4 n/c 13 TXM TX Mute*
5 n/c 14 DTR Data Terminal Ready
6 n/c 15 DCD Data Carrier Detect
7 P12V +12V DC Power 16 RXD Receive Data RS232
8 TX+ Differential Transmit Data 17 TXD Transmit Data RS232
9 TX- Differential Transmit Data 18 GND Ground

Note dimple next to pin 1. (*) active with short to ground.

Appendix C C-2 ANACOM ANASAT®–Protection Switch

 ANACOM 3073906

18-Pin Circular Weathertight Connector: ODU-A and ODU-B

10 1112 1 1 11
9 17 18 13 2 2 12

16 3 13 17 109
8 3 18
15 14 16
7 4 14 15
4 8
6 5 5
6 7

Cable End View Cable Wire View

Pin Signal Description Pin Signal Description

1 RY1NC RX Alarm Normally Closed 10 RX+ RS-485 Receive Data
2 n/c 11 RX- RS-485 Receive Data
3 RY1C RX Alarm Common 12 RS485 RS485 Jumper (open for 232)
4 n/c 13 TXM TX Mute*
5 RY2NC TX Alarm Normally Closed 14 DTR Data Terminal Ready
6 RY2C TX Alarm Common 15 DCD Data Carrier Detect
7 P13V +13 Volts DC Power 16 RXD Receive Data RS232
8 TX + RS-485 Transmit Data 17 TXD Transmit Data RS232
9 TX - RS-485 Transmit Data 18 GND Ground

Note dimple next to pin 1 * active with short to ground

ANACOM ANASAT®–Protection Switch C-1 Appendix C

 ANACOM 3073905

Appendix D. Drawings and Diagrams

ANASAT®-PS Simplified Signal Flow Block Diagram

ANACOM ANASAT®–Protection Switch D-1 Appendix D

 ANACOM 3073906

COAX / WAVEGUIDE
TX OUT

ODU - A
COAX
RX IF

TX IF

M&C
LNC
COAX

COAX

LNC-A
18

T/R OMT
6
RX IF A

TX IF A

M&C A

LNC-B
RX - RELAY RX CONTROL
COAX
TX IF CABLE
TO MODEM Protection
COAX /
EQUIPMENT Switch WAVEGUIDE
RX IF
COAX
RX IF B

TX IF B

M&C B

6
TX - RELAY
TX CONTROL
CABLE
COAX

COAX

18
RX IF

TX IF

M&C

TX OUT
COAX / WAVEGUIDE
ODU - B
LNC
COAX

ANASAT®-PS Cabling Interconnection Diagram.

Appendix D D-2 ANACOM ANASAT®–Protection Switch

 Appendix D
3073905

10956 WR-75 waveguide, Ku Band

11706 Andrew PNR-HC/F1PNM-H C Band
TX OUT
TRANSCEIVER - A
COAX 31198-010
RX IF

TX IF

M&C

LNC

COAX / WAVEGUIDE
WR229 Switch 10927 C Band

10958 Ku band
10947 C band
WR75 Switch 10955 Ku Band
30641-003

30641-003

31197-003
18 PIN

LNC-A
COAX

COAX

C Band TRF 10917

Ku Band TRF 10968
RX CONTROL CABLE T/R OMT
6 PIN 30933-010
RX IF A

TX IF A

M&C A

LNC-B
RX - RELAY
* COAX TX IF
TO MODEM
EQUIPMENT * COAX Protection WR137 Switch 10928 C Band
RX IF
31048-010RS-232 / M&C
Switch WR75 Switch 10955 Ku Band
M&C 32313 10946-250 C band
31199-010RS-485 / M&C
RX IF B

TX IF B

M&C B
COAX / WAVEGUIDE

D-3
10958-250 Ku band
TX - RELAY (customer provided)

COAX / WAVEGUIDE
* IFL cables should be 100% shielded: TX CONTROL CABLE
Belden 9913 or equivalent 6 PIN 30933-005
(Customer provided)

30641-003

31197-003
30641-003
ANACOM

COAX

COAX

18 PIN

ANACOM ANASAT®–Protection Switch

RX IF

TX IF

M&C
TX OUT
10956 WR-75 waveguide, Ku Band
TRANSCEIVER - B 11706 Andrew PNR-HC/F1PNM-H C Band
LNC
COAX 31198-010
ANACOM 1 + 1 Redundancy Protection Switch Cabling Diagram
(C Band, Single Enclosure)
(Ku Band, Single Enclosure) ANACOM 30908 REV07
3090807_PS Block.vsd. 11/07/2013
 ANACOM ANASAT®–Protection Switch
3073906

TX OUT
COAX HPA - A
30641-005
M&C
TRANSCEIVER - A COAX
RX IF

TX IF

M&C

LNC 31198-010

10945-003 WR137, C band

10956-003 WR75, Ku band
32126-010 AnaSat SSPA

WAVEGUIDE
WR229 Switch 10927 C Band
30952-010 Xicom
WR75 Switch 10955 Ku Band
30641-003

30641-003

31059-010 Xicom / MTN

COAX

COAX

LNC-A
18

30756-003 RS-232 C Band TRF 10917*

Ku Band TRF 10968*
31197-003 RS-485
RX CONTROL T/R OMT
CABLE
6
RX IF A

TX IF A

M&C A 30933-010

LNC-B
RX - RELAY
* COAX TX IF
TO MODEM
EQUIPMENT * COAX
RX IF
Protection WR137 Switch 10928 C Band
WR75 Switch 10955 Ku Band
31048-010RS-232 M&C Switch
31199-010RS-485 M&C M&C Load depends
RX IF B

TX IF B

M&C B
6 on HPA power WAVEGUIDE
w RS232--RS485 adapter

D-4
TX - RELAY (customer provided)
30933-005

10945-003 WR137, C band

10956-003 WR75, Ku band
TX CONTROL
CABLE

WAVEGUIDE
30641-003

30641-003
30756-003 RS-232
* Optional TRF should be
ANACOM

COAX

COAX
* IFL cables should be 100% shielded: 31197-003 RS-485 32126-010 AnaSat SSPA
used if not included with

18
Belden 9913 or equivalent 30952-010 Xicom
(Customer provided) 31059-010 Xicom / MTN antenna feed system
M&C

RX IF

TX IF

M&C
COAX
TX OUT HPA - B
30641-005
TRANSCEIVER - B
COAX
LNC
31198-010
ANACOM 1 + 1 Redundancy Protection Switch Cabling Diagram
(External HPA)

Appendix D
ANACOM 30909 Rev 05
3090905 .vsd. 11/07/2013

 Appendix D
3073905

10959 Ku adapter
User Supplied Cable Block Down Converter
L-Band Out
31052-014
11013
COAX HPA - A Part of 50 ohm
TX OUT Optional Ganged
30641-005
M&C RX Coax Switch
TRANSCEIVER - A COAX Block Down Converter
10990 Ku band
RX IF

TX IF

M&C

LNC 31198-010

10945-003 WR137, C band

10956-003 WR75, Ku band
32110 C band
32126-010 AnaSat SSPA

WAVEGUIDE
WR229 Switch 10927 C Band
30952-010 Xicom
WR75 Switch 10936 Ku Band
30641-003

30641-003

31059-010 Xicom / MTN

COAX

COAX

LNC-A
18

30756-003 RS-232 C Band TRF 10917*

31197-003 RS-485 Ku Band TRF 10968*
RX CONTROL T/R OMT
CABLE
6
RX IF A

TX IF A

M&C A
30933-010

LNC-B
RX - RELAY
* COAX 31053-014 Ku
TX IF
TO MODEM
EQUIPMENT * COAX Protection WR137 Switch 10928 C Band 31052-014 C

D-5
RX IF
31048-010 RS-232 M&C Switch WR75 Switch 10955 Ku Band
31199-010 RS-485 M&C M&C
RX IF B

TX IF B

M&C B
6 WAVEGUIDE
w RS232--RS485 adapter TX - RELAY (customer provided)
30933-005

10945-003 WR137, C band

10956-003 WR75, Ku band
ANACOM

TX CONTROL
CABLE

WAVEGUIDE
30641-003

30641-003
30756-003 RS-232
* Optional TRF should be

COAX

COAX

ANACOM ANASAT®–Protection Switch

* IFL cables should be 100% shielded: 31197-003 RS-485 32126-010 AnaSat SSPA

18
Belden 9913 or equivalent 30952-010 Xicom used if not included with
(Customer provided) 31059-010 Xicom / MTN antenna feed system
M&C

RX IF

TX IF

M&C
COAX
TX OUT
30641-005
HPA - B
TRANSCEIVER - B
COAX
LNC
31198-010
ANACOM 1 + 1 Redundancy Protection Switch Cabling Diagram
(External HPA)
ANACOM 30909 Rev 05
3090905 -L.vsd. 11/07/2013

 Appendix D
3073905

10945-003 (1 meter)
TX OUT
WAVEGUIDE
BUC - A
COAX
TX IF

M&C

31198-010
30641-003

31197-003

WR229 Switch 10927

18 PIN

LNB-A
COAX

Termination
C Band TRF 10917 *

10947
RX CONTROL CABLE T/R OMT
RX IF A

6 PIN 30933-010
TX IF A

M&C A

LNB-B
RX - RELAY
* COAX TX IF
TO MODEM
EQUIPMENT * COAX Protection Switch WR137 Switch 10928
RX IF
RS-232 / M&C 32313-L WAVEGUIDE
M&C 10946
31336-010 (customer provided,
RX IF B
TX IF B

M&C B

Termination length depends on

D-6
TX - RELAY installation)
* IFL cables should be 100% shielded: TX CONTROL CABLE
Belden 9913 or equivalent 6 PIN 30933-005
(Customer provided)
31197-003
30641-003
COAX
ANACOM

18 PIN
COAX 31198-010
NOTE: RX side cables can be ordered

ANACOM ANASAT®–Protection Switch

with different lengths if needed.
* Optional TRF should be used if not

M&C
TX IF
included with antenna feed system
BUC - B
10945-003 (1 meter)
TX OUT
WAVEGUIDE
ANACOM 1 + 1 Redundancy Protection Switch Cabling Diagram
(Wave guide C Band, BUC + LNB)
ANACOM 31302-L Rev 02
31302-L Block.vsd. 11/07/2013

 Appendix D
3073905

N connector
11706-003 (1 meter)
TX OUT
LOW LOSS COAX
BUC - A
TX IF

M&C

31198-010
COAX
30641-003

31197-003

WR229 Switch 10927

18 PIN

LNB-A
COAX

Termination
C Band TRF 10917 *

10947
RX CONTROL CABLE T/R OMT
6 PIN 30933-010
TX IF A

M&C A

LNB-A

LNB-B
RX - RELAY
* COAX
TO MODEM TX IF
* COAX
EQUIPMENT RX IF Protection Switch WR137 Switch 10928
RS-232 / M&C 32313-L WAVEGUIDE
M&C 10946
31336-010 (customer provided,
TX IF B

M&C B

Termination
LNB-B
length depends on

D-7
TX - RELAY installation )
* IFL cables should be 100% shielded: TX CONTROL CABLE
Belden 9913 or equivalent 6 PIN 30933-005
(Customer provided) N to waveguide
31197-003
30641-003
adapter (2)
COAX
COAX 31198-010
ANACOM

18 PIN
10948
NOTE: RX side cables can be ordered

ANACOM ANASAT®–Protection Switch

with different lengths if needed .
* Optional TRF should be used if not

M&C
TX IF
included with antenna feed system
N connector
BUC - B
11706-003 (1 meter)
TX OUT
LOW LOSS COAX
ANACOM 1 + 1 Redundancy Protection Switch Cabling Diagram
(N Type C Band , BUC + LNB)
ANACOM 31258-L Rev 02
31258 -L Block.vsd. 11/07/2013

 ANACOM 3073906

Appendix D D-8 ANACOM ANASAT®–Protection Switch

 ANACOM 3073905

ANACOM ANASAT®–Protection Switch D-9 Appendix D