Polish J. of Environ. Stud. Vol. 20, No.

4 (2011), 925-930

Original Research
Comparison of Analytical and Numerical Solutions
for Steady, Gradually Varied Open-Channel Flow

Jacek Kurnatowski*

Department of Hydroengineering, West Pomeranian University of Technology,

Piastów 50a, 70-311 Szczecin, Poland

Received: 9 August 2010

Accepted: 21 January 2011

Abstract

The depths for a steady, gradually varied flow in a rectangular open channel with infinite width obtained
analytically by the Bresse formula and numerically using trapezoidal rule for integration have been compared.
It has been shown that numerical integration may generate significant errors of flow values for looped river
networks. The method for choosing the optimum integration step that minimizes numerical integration errors
has been presented.

Keywords: open-channel flow, river looped networks, gradually varied flow, Bresse formula, numeri-
cal integration

Introduction bilities of computational accuracy improvement by relevant

numerical integration are shown.
Among various open-channel systems, a special position
is occupied by looped networks, i.e. networks with cyclic Gradually Varied Flow in Open Channels –
sequences of reaches. Looped structure often happens at irri- Analytical Solutions
gation systems; in the case of rivers this this results from nat-
ural bifurcations, in particular at deltaic mouths, like the Red The energy equation is the base for all methods of
River in Vietnam, the Ganges and the Mekong [1] as from steady, gradually varied flow computations in open chan-
hydrotechnical works (bypasses). Rivers of braided and nels. Assuming abscissa x directed opposite the flow (Fig.
anastomosing types [2] can be perceived as looped networks 1), this equation can be presented in a differential form:
as well. The Lower Oder River is an example of such a sys-
Dv 2 D
tem in Poland [3]. z z  dz  v  dv 2  Sdx (1)
Looped networks are worthy of special regard among 2g 2g
others due to the fact that any local change of flow condi-
tions, e.g. the narrowing or deepening of a river bed in one ...where z – water surface elevation [m], α – Coriolis coef-
place, may affect the flow values at the major part of the ficient [-], v – mean velocity in a cross-section [m·s-1], g –
network. Hence, these networks require computational gravity [m·s-2], S – energy line slope (hydraulic slope) [-], or
methods that allow us to determine flows and water levels in an integral one:
D
with high accuracy.
The present paper aims to show circumstances of signif-
z 2  z1 
2g
v 2
2
 v1
2
 ³ x2

x1
Sdx (2)
icant errors at flow determination in looped networks using
standard numerical methods. Simultaneously, some possi-
...where z1, z2 are elevations and v1, v2 are mean velocities in
*e-mail: [email protected] cross-sections positioned at x1 and x2, respectively.
926 Kurnatowski J.

Considering the rectangular bed cross-section, Eq. (1) can Analytical solution for equation (5) was given by
be written as follows: Venutelli [5].
dh S  S0
dx 3 (3) Gradually Varied Flow in Open Channels –
§h · Comparison of Numerical and Analytical
1 ¨ c ¸
©h¹ Solutions
...where h is depth [m], hc – critical depth [m], S0 – bed
The integral form (2) of a gradually varied flow equa-
slope [-]. tion is basically applied in natural channels, while energy
Solution of Eq. (3) requires specification for the energy losses being an integral of the hydraulic slope function are
loss function. Assuming the concept of the infinitely wide calculated using the trapezoidal rule method [6]:
channel with a constant bed slope as a base for further con-
siderations, at constant value of Chézy coefficient Eq. (3) is x  'x
S  x  'x   S  x 
given by: ³ Sdx # ˜ 'x
3 x
2 (9)
§h ·
1 ¨ n ¸
dh © h¹ This method is widely accepted as a sufficiently accu-
S 0 3 (4) rate one [4, 7], so the applications of other methods of
dx §h ·
1 ¨ c ¸ numerical integration, like Runge-Kutta [4, 8] or Kutta-
©h¹ Merson [4], are rare.
Some researchers [1, 9], while discussing methods of
...where hn is the normal depth [m], while Manning’s
flow calculations in looped networks, assume arbitrarily the
approach leads to the equation:
acceptable error of water elevations in a single integration
10 / 3
§h · step as 0.001 m, which creates an impression of accuracy
1 ¨ n ¸
dh © h¹ sufficient for practical purposes. Adlul Islam et al. [10],
S 0 3
(5) comparing the effectiveness of various algorithms for river
dx §h ·
1 ¨ c ¸ network calculations, assume (also arbitrarily) the accept-
©h¹ able error ten times smaller, i.e. 0.0001 m. However, con-
The analytical solution of Eq. (4) is known as the Bresse sidering the looped network as the trapezoidal method as
formula [4], which is for the given initial condition (x0, h0) the mentioned error, values may appear insufficiently accu-
and at the following denotations: rate, as in the example discussed below.
Example: Let us consider a river network (Fig. 2) con-
h hc sisting of two main channels, 2-1 and 3-1, with constant bed
y, E , E3 Fr 2 (6) slope joined in node No. 1 and connected additionally by
hn hn
transverse channel 2-3. The following assumptions are
...where Fr is a Froude number for uniform flow and may made:
be written as follows: - cross-sections for each channel are rectangular with
infinite width,
S 0 x  x0  - the Chézy coefficient for each channel is a constant
F  y0   F  y  (7)
hn independent of the depth and calculated as for uniform
flow due to the Manning formula for the given rough-
...where:
ness coefficient n.
1
F y y
6

1  Fr 2 ˜  These assumptions make the Bresse formula (7, 8) the
exact solution for the problem of water surface level deter-
ª  y  13 3 º (8) mination for each reach of the network. Although Manning
«ln 3  2 3 ˜ arctan »
¬ y 1 2 y  1¼ formula is basically redundant here due to the invariability
of the Chézy coefficient, it was used to demonstrate the
I II proximity of assumptions to a possible real situation.
Z Using independently the Bresse formula and the inte-
gral form of Eq. (2) at different integration steps Δx by
Sdx energy line Į(v  dv) 2
Įv2 2g
water surface
2g
2
v v+dv
z+dz
z bottom 1

datum
X
dx 3
Fig. 1. Gradually varied open-channel flow. Fig. 2. Example of cyclic looped river network.
Comparison of Analytical and Numerical... 927

Table 1. Determination of flows in an example of a cyclic looped river network.

Assumptions
Reach
Value
2-1 3-1
Lengths [m] 2,000 2,000
Bed slopes [-] 0.001 0.001
Unit flows [m2s-1] 3.00 5.00
Roughness coefficients [m-1/3s] 0.032 0.020
Depth in node No. 1 [m] 3.000
Reach 2-3
Length [m] 200
Bed slope [-] 0
Roughness coefficient [m s] -1/3
0.026
Calculation results
Reach
Values common for both methods
2-1 3-1
Normal depths [m] 1.95 2.00
Critical depths [m] 1.00 1.41
1/2 -1
Chézy coefficients [m s ] 34.92 56.10
Values for particular methods Bresse (exact) Δx=500 m Δx=1,000 m Δx=2,000 m
Depths in node No. 2 [m] 2.05405 2.05277 2.04994 2.05754
Errors of depth in node No. 2 in relation to
0 -1.28 -4.11 +3.49
exact value [mm]
Depths in node No. 3 [m] 2.05337 2.05028 2.04189 2.04430
Errors of depth in node No. 3 in relation to
0 -3.09 -11.48 -9.07
exact value [mm]
Unit flow at reach 2-3 [m2s-1] 0.235 0.450 0.805 1.036

trapezoidal rule (9), unit flow at reach 2-3 should be calcu- 2. Calculation of depths in nodes 2 and 3 using adopted
lated. The following values have been assumed for reaches methods.
2-1 and 3-1: 3. Determination of unit flow at reach 2-3 using the
- unit flows q [m2s-1], Chézy-Manning formula.
- Manning roughness coefficient n [m-1/3s]. All assumptions and results of computations performed
Additionally the following values are given: due to the presented algorithm are shown in Table 1.
- depth in the node No. 1 common for both main reaches Analysis of the calculation results shows that differ-
h0 [m], ences between exact water level elevations and the eleva-
- constant Coriolis coefficient α=1.1. tions obtained by integration of energy losses using trape-
The sequence of calculations is presented below: zoidal rule method are seemingly small and negligible
1. Determination of critical depth, normal depth, and (a few millimeters); however, these differences are the
Chézy coefficients for reaches 2-1 and 3-1 due to the source of high changes of calculated unit flow values at
relations: reach 2-3. This may produce biased results of mathematical
modeling of flows in a complicated river network with
3/ 5
§ q˜n · looped structure and give even entirely false flow condi-
¨ ¸ D ˜ q2
hn , hc 3 , tions in such a network as a consequence. Additionally, the
¨ S ¸ g elevation differences are not a monotone function of the
© 0¹
(10) integration step length Δx.
1 1/ 6 Therefore, the problem of accuracy for water level
C hn
n determination is essential when gradually varied flow has
928 Kurnatowski J.

been considered by an integral form of the energy equation Calculations of the λ values were performed for the fol-
(2). In particular, the proper choice of the integration steps lowing ranges: β∈〈0,1〉, γ∈〈0;1.5〉, and y*∈〈−1;2〉. This
minimizing the errors of channel depths and elevations variability covers practically the whole range of flow para-
determination becomes important. Earlier, this problem meters at backwater computations. The graphs for some β
was reported by Tavener [11]. Next, Družeta et al. [12], values are shown in Fig. 3. It results that for the given val-
while analyzing the influence of finite element size on the ues of β and γ there exists only one value y*=y0*, where
accuracy of the solution for the 2-D open-flow problem, λ=0.5 and numerical integration by trapezoidal rule gives
showed the existence of an optimal element size that, when an unbiased result. Analogically, at given values β and y*
decreased, may produce the worse quality of the model. there exists the single (at the outmost) value γ=γ0 fulfilling
One of the possible analysis options is the application of this condition. This means that while performing one inte-
the modified trapezoidal rule due to the formula: gration step for the gradual flow equation (4) by trapezoidal
x  'x
rule, the depth is equal to the exact analytical value at one,
³ Sdx >O ˜ S x  'x   1  O  ˜ S x @ ˜ 'x (11) if any, length of the spatial integration step Δx=Δx0. The
x1 graphs show that at sufficiently small values y* (one may
estimate y*<0, so at depths h≥2·hn) the value Δx0>0 does not
...where λ is the weight coefficient, and determination of exist; therefore, every integration step must be biased.
the λ value that results in the numerical integral of the ener-
Worthy of notice is that at y*≅y0*, plots λ=λ(β,γ,y*) have point
gy head losses equal to the relevant analytical value.
of inflexion and high gradients that cause each inexactness
For rectangular channel Eq. (2) yields:
of y0* determination affecting λ value relatively strongly.
Dq 2 Dq 2 x1 'x Substituting λ=0.5 and putting γ=γ0 to Eq. (18) the fol-
h1  2
h2  S 0 ˜ 'x  2
 ³ Sdx (12) lowing inverse function can be found:
2 gh1 2 gh2 x1

...where Δx = x2 – x1. Assuming conditions adequate to the y 0* y 0* E , J 0  (20)

Bresse solution the hydraulic slope can be expressed as:
The graphs for relation (20) are shown at Fig. 4, whilst
2 3 coefficients of the approximating trinomial function
q §h ·
S x  2 3
S 0 ¨¨ n ¸¸ (13)
C h © h ¹ 2
y 0* a 0 E   a1 E  ˜ J 0  a 2 E  ˜ J 0 (21)
Therefore, using denotations (6), relations (10), and for-
mula (11), Eq. (12) can be written as: are given in Table 2 together with relevant determination
coefficients R2.
ª 1 § E ·3 º
y1 «1  ¨¨ ¸¸ »
«¬ 2 © y1 ¹ »¼
ª 1 § E ·3 º S ˜ 'x ª § 1 (14) Table 2. Approximation of the relation y0*=y0*(β, γ0).
1 · 1 º
y2 «1  ¨¨ ¸¸ »  0 «O ¨¨ 3  3 ¸¸  3  1»
«¬ 2 © y2 ¹ »¼ hn «¬ © y2 y1 ¹ y1 »¼ β a0 a1 a2 R2
0.00 0.6879 -0.4538 0.0646 1.0000
Rewriting Eq. (7) in a form:
0.10 0.6881 -0.4542 0.0647 1.0000
S 0 ˜ 'x
F  y1   F  y 2  (15) 0.20 0.6892 -0.4562 0.0652 1.0000
hn
0.30 0.6922 -0.4622 0.0670 1.0000
...the set of equations is obtained that allows us to determine 0.40 0.6982 -0.4739 0.0706 1.0000
relevant λ value for any integration step as a function:
0.50 0.7087 -0.4953 0.0773 1.0000
O O E , J , y 2  (16) 0.55 0.7163 -0.5109 0.0823 1.0000
...where: 0.60 0.7260 -0.5312 0.0890 1.0000
S 0 ˜ 'x
J (17) 0.65 0.7383 -0.5577 0.0981 1.0000
hn
0.70 0.7540 -0.5926 0.1104 1.0000
For practical reasons it is more convenient to show the 0.75 0.7745 -0.6396 0.1277 1.0000
relation (16) in a logarithmic scale, i.e.:
0.80 0.8017 -0.7050 0.1532 0.9999
O O E , J , y
 (18) 0.85 0.8392 -0.8004 0.1928 0.9998
...where: 0.90 0.8949 -0.9514 0.2605 0.9993
y  log10  y 2  1 (19) 0.95 0.9899 -1.2301 0.3979 0.9968
Comparison of Analytical and Numerical... 929

1,0 1,0

E = 0.0
0,9 0,9

0,8 0,8
J = 1.5
0,7 J = 1.0 0,7

J = 0.7
0,6 0,6
J = 0.4
O J = 0.1 0,5
0,5
y 0* E = 0.95

0,4
0,4 E = 0.90
E = 0.80
0,3
0,3
E = 0.70
0,2
0,2 E = 0.60

0,1 E = 0.50
0,1
E = 0.00
0,0
0,0
0,0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5
-1,0 -0,5 0,0 0,5
y* 1,0 1,5 2,0 J0

Fig. 4. Values y0* at different β and γ0.

1,0
E = 0.3
0,9

0,8
J = 1.5 Application of linear interpolation to the trinomial
0,7 J = 1.0 approximation coefficients given in Table 2 for the first step
J = 0.7
0,6
of the energy equation integration in the main reaches of the
J = 0.4
O
0,5
J = 0.1 example river network results in the following values:
– for the reach 2-1: β=0.513, y0*=0.269, γ0=1.062,
0,4
Δx0=2,071 m (exact value – 2,076 m),
0,3
– for the reach 3-1: β=0.705, y0*= 0.301, γ0= 0.919,
0,2
Δx0= 1,838 m (exact value – 1,847 m).
0,1

0,0
-1,0 -0,5 0,0 0,5 y* 1,0 1,5 2,0
Conclusions
1,0

E = 0.6 The simulations performed have revealed that numeri-

0,9
cal integration of the steady, gradually varied flow in
J = 1.5
0,8 looped networks of infinitely wide rectangular open chan-
0,7 J = 1.0 nels may lead to significant errors of water level slopes and
J = 0.7
0,6
be the source of errors of flow values at particular reaches
J = 0.4
O J = 0.1 of the network. It has been shown that numerical integra-
0,5
tion of this equation is exact only for at most one integra-
0,4
tion step with its length being a function of the flow para-
0,3 meters. Therefore, in order to obtain the unbiased solution,
0,2 one may either apply specified inconstant step length or
0,1
modify trapezoidal rule by application of variable weight
coefficients according to Eq. (11).
0,0
-1,0 -0,5 0,0 0,5
y* 1,0 1,5 2,0 One can anticipate that similar relations exist for a rec-
tangular channel of finite width; however, weight coeffi-
1,0 cients as optimum integration steps require further research
E = 0.9 J = 1.5
0,9 in this case.
J = 1.0 J = 0.7
0,8

0,7 J = 0.4
References
0,6
J = 0.1
O
0,5 1. PRASHANTH REDDY H., MURTY BHALLAMUDI S.
0,4 Gradually Varied Flow Computation in Cyclic Looped
Channel Networks. Journal of Irrigation and Drainage
0,3
Engineering, ASCE, 130, (5), 424, 2004.
0,2 2. SMITH D.G. Anastomosed fluvial deposits: modern exam-
0,1
ples from Western Canada. Special Publications,
International Association of Sedimentologists, 6, 155, 1983.
0,0
-1,0 -0,5 0,0 0,5
y* 1,0 1,5 2,0 3. KURNATOWSKI J. River Roughness Coefficient as
a Function of Vertical Reference System. Polish Journal of
Fig. 3. Sample values of λ at different β, γ, and y*. Environmental Studies, 18, (5A), 279, 2009.
930 Kurnatowski J.

4. SUBRAMANYA K. Flow in Open Channels, 3rd ed. Tata Varied Flows in Channel Networks. Journal of Irrigation and
McGraw-Hill Publishing Co. Ltd., New Delhi, India, 2009. Drainage Engineering, ASCE, 128, (6), 351, 2002.
5. VENUTELLI M. Direct Integration of the Equation of 10. ADLUL ISLAM, RAGHUWANSHI N.S., SINGH R., SEN
Gradually Varied Flow. Journal of Irrigation and Drainage D.J. Comparison of Gradually Varied Flow Computation
Engineering, ASCE, 130, (1), 88, 2004. Algorithms for Open-Channel Network. Journal of Irrigation
6. MITOSEK M. Fluid mechanics in engineering and environ- and Drainage Engineering, ASCE, 131, (5), 457, 2005.
mental protection. Wydawnictwo Naukowe PWN, 11. TAVENER G.F. Stability and Reach Length in Water
Warszawa, 2001 [In Polish]. Surface Profile Determination. Water Resources Bulletin,
7. CHOW V.T. Open-Channel Hydraulics. McGraw-Hill Book AWRA, 9, (5), 950, 1974.
Co. Inc., 1959. 12. DRUŽETA S., SOPTA L., MAĆEŠIĆ S., CRNJARIĆ-ŽIC
8. SAWICKI J. Free-surface flows. Wydawnictwo Naukowe N. Investigation of the Importance of Spatial Resolution for
PWN, Warszawa, 1998 [In Polish]. Two-Dimensional Shallow-Water Model Accuracy. Journal
9. SEN D.J., GARG N.K. Efficient Algorithm for Gradually of Hydraulic Engineering, ASCE, 135, (11), 917, 2009.
Copyright of Polish Journal of Environmental Studies is the property of Scientific Investigation Committee and
its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's
express written permission. However, users may print, download, or email articles for individual use.