Republic of the Philippines

UNIVERSITY OF RIZAL SYSTEM

Antipolo City
A.Y. 2019 – 2020

COLLEGE OF ENGINEERING

Assignment/Individual Research No. 03

Work Method Statement

In partial fulfilment of the requirements in

CE 16: Timber Design

Presented by:

Jomarie A. Paclibar
Student No.: 1011500160

Submitted to:

George Prejula Palada, RCE

Instructor

23 September 2019
 Work Method Statement
Construction of Timber Stud Wall and Installation of Ceiling Drywall

I. Introduction
A method statement explains in a logical sequence precisely how a work is
to be performed in a secure way and without health hazards. It involves all the
hazards recognized in the risk evaluation and the measures required to regulate
those hazards.
II. Purpose / Scope of work
The primary purpose of method statement is to assist supervisors,
employees and any other individuals at the workplace in understanding the criteria
that have been developed for the secure and healthy performance of high-risk
construction work.
III. Standard References
1. Contract documents
a. Project Specification
b. Contract Drawings
2. Contractors Submittal
a. Project Quality Plan
b. Project Safety Plan
c. Material approvals (MAT)
d. Shop Drawings approvals (SPD)
e. Related method statements (MET)
IV. Definitions and Abbreviation
 Project Manager – It is accountable for the general execution of the MET.
He will guarantee that this MET is assigned by the supervisory employees.
 Site Engineer – It is accountable for performing the installation work
according to the MET authorized.
 QA/QC Engineer – It is accountable for ensuring that research is carried out
in accordance with the specifications and that checks are carried out in
accordance with the ITP authorized.
 Safety Officer – Is accountable for ensuring that all on-site staff comply with
the safety demands of the project.
 ITP – Inspection and Test Plan
 MAT – Material Submittal
  MET – Method Statement
 PPE – Personal Protective Equipment
 QA / QC – Quality Assurance and Quality Control
 SPD – Shop Drawing
V. Materials Definitions and Specification
 Ceiling Plate – (also known as Top Plate) is the continuous timber beam on
top of the walls that supports the roof structure by carrying the vertical forces
from the rafters to the wall studs. End joints in top plates shall be offset not
less than 24 inches (610 mm).
 Sole Plate – (also known as Sill Plate) in construction and architecture is the
bottom horizontal member of a wall or building to which vertical members are
attached. Soleplates shall be a minimum of 2-inch by 4-inch (51 mm by 102
mm) nominal lumber.
 Timber Stud – is a vertical framing member which forms part of a wall or
partition that may carries vertical structural load, or as part of a partition wall,
may be non-load bearing. Timber stud is typically either 90mm or 70mm deep
with 35mm or 45mm thick studs depending on load and spacing — usually
450–600mm.
 Furring Strips – are thin strips of wood or other material to level or raise
surfaces of another material to prevent dampness, to make space for
insulation, or to level and resurface ceilings or walls. The general rule to install
furring strips that are the same width as the ceiling joists.
 Drywall — (also known as plasterboard, wallboard, sheet rock, gypsum board,
or gypsum panel) used in the construction of interior walls and ceilings. When
installed on ceilings, 5/8-inch-thick panels are more resistant to sagging than
1/2-inch panels.
VI. Work Method Statement
The process to construct a timber stud wall is outlined below:
1. Mark out the position of the internal walls as per the site plan.
2. Measure and cut the Ceiling Plate.
3. Nail fix the Ceiling Plate through into the joists.
4. Measure and cut the Sole Plate.
5. Nail fix the Sole Plate ensuring they are plumb with the Ceiling Plate.
6. Mark out the position of the Studs on both the Ceiling Plate & Sole Plate.
7. Measure each stud and mark up in case of any variation.
8. Skew nail each stud both top and bottom and check for vertical with the spirit
level.
9. Mark out the position for the horizontal noggins as per site plan.
10. Nail fix the horizontal noggins.
11. Measure and cut to size the interior door frames.
12. Nail to stud frame ensuring frame is square and plumb.
13. Ensure area is left safe at end of each shift.
14. Remove all waste and dispose of as per local authority guidelines.
The process to install ceiling drywall is outlined below:
1. Inspect the ceiling for obstructions or problems that need to be fixed. (NOTE:
Make sure the electrical wires, ductwork, protruding pipes, and other
obstructions won’t be in your way. As well, take this opportunity to make
sure there aren’t any obvious issues, such as faulty plumbing, that would be
easier to address without drywall in the way.)
2. Install furring strips to the framing in order to create a flat, even surface for
drywall installation around these obstacles as necessary.
3. Find the ceiling joists and mark their location on the wall.
4. Mark the placement of light fixtures and vents on the drywall.
5. Smooth the rough edges of the drywall pieces.
6. Build a T-brace if you’ll be working alone or without a lift.
(NOTE: A T-brace will provide the leverage and support needed to raise the
drywall panels to the ceiling when you're working alone. Use a 2 feet (61 cm)
piece of 1x4 and nail it to a 2x4 that is long enough to be 1 foot (30 cm)
higher than the length from the floor to the ceiling.)
7. Apply adhesive to the joists where the first sheet of drywall will go.
(NOTE: Drywall adhesive dries within 15 minutes, so make sure you’re ready
to begin placing the drywall as soon as you apply the adhesive.)
8. Raise the first piece of drywall to the ceiling.
9. Repeat this process along the first wall.
10. Affix the drywall sheets permanently to the ceiling joists.
(NOTE: Use either nails or screws to attach the drywall to the joists. Drive
the fasteners in .375 inches (0.95 cm) away from the edges of each sheet
and space them 7 inches (18 cm) apart along the perimeter. Along the interior
joist, install the fasteners at about 12 inches (30 cm) increments.
11. Start the second row with a half sheet of drywall to stagger the seams.
 (NOTE: When you finish the first row of drywall and move on to the second,
make sure the seams don’t line up between the two rows. Having staggered
seams will enforce the stability of the drywall.)
12. Repeat this process until the entire ceiling is covered.
13. Go back and cut holes in the drywall for vents and fixtures.
VII. Quality Assurance and Control
The QA / QC Manager will monitor and guarantee that this Method
Statement is followed in such a way that smooth work flow is achieved. In addition,
the QA / QC team will ensure that each individual component of the work is
substantially completed in accordance with the approved plans and project
specifications to meet the expectations of the client.

VIII. Inspection Test Plan

IX. Safety
The safety precautions from construction of timber stud wall drywall are outlined
below:
 Keep all hand tools clean, sharp and in good repair.
 Use all hand tools for the purpose for which they were intended.
 Do not carry sharp/pointed objects in pockets.
 Wear approved PPE at all times.
 Inspect work area for unsafe conditions, remedy before beginning work.
 Maintain appropriate safety margin between cutting edge and hands.
 Make all adjustments and tighten all locking devices before attaching tool to
power supply.
 The safety precautions from installation of ceiling drywall are outlined below:
 Taking care accessing and traversing the work area, avoiding tripping over
debris, material and the ceiling trusses;
 Being aware of the location of electrical cables, fittings and equipment and
avoiding contact with them.
 Making sure you do not damage any electrical cables or electrical equipment.
(NOTE: if any electrical cable or equipment is damaged, consult with the
owner and engage a licensed electrical contractor to inspect the installation.)
 Wearing appropriate, well maintained and correctly-fitted personal protective
equipment when working in dusty ceiling spaces, including:
 A half-face (class P1 or P2) disposable particulate respirator, in
accordance with AS/NZS 1715.
 A head covering and goggles, to avoid eye irritation.
 Long-sleeved, loose-fitting clothing and gloves, to minimize skin contact
with insulation material.
 Wearing appropriate footwear.
 Keeping your work areas clean and clear of fibers and dust and place waste
in plastic bags capable of containing the dust.

X. Risk Assessment / Job Hazard Analysis

The hazards from construction of timber stud wall and installation of ceiling drywall
are outlined below:
 Injury hazards from the use of various machinery and tools.
 Exposure to toxic molds, fungi and bacteria.
 Toxic hazards from exposure to chemicals, solvents and other materials.
 Cancer from exposure to solvents, formaldehyde in pressed wood, and wood
dust.
 Exposure to flammable or combustible materials, including wood dust.
 Injury from working in awkward positions, performing repetitive tasks, and
lifting.
 Risk of eye injury from flying particles.
 Risks of falling from working at heights.
 Stress and increased risks of injury from shift work and extended work days.
XI. Resources
 Jonhume,2013. Safety Precautions. Retrieved from https://visual.ly
 Deakin,2019. Timber Stud. Retrieved from https://adeakindevelopmentsltd.com/
 NA. Ceiling System. Retrieved from https://worldarchi.com
 NA. Working in ceiling spaces. Retrieved from www.commerce.wa.gov.au/worksafe
XII. Appendix

Construction of Timber Stud Wall

Installation of Ceiling Drywall