MOP of setup RET in SRAN 18SP

Method of Procedure for

Setup RAN in SRAN 18SP
Nokia - 2018
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

Revision Record

Date Revised Version Change description Author

2
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

Table of Contents

1. EXECUTIVE SUMMARY……………………………………………………………………………………………… 4
2. BACKGROUND AND OBJECTIVES…………………………………………………………………………….… 5
3. SCOPE OF WORK………………………………………………………………………………………………………. 7
4. DETAIL TIME AND TABEL OVERALL ACTIVITY……………………………………………………………. 10
5. SERVICE AND AREA IMPACT…………………………………………………………………………………….. 11
6. TESTING AND VERIFICATION……………………………………………………………………………………. 12
7. ROLLBACK OPERATION…………………………………………………………………………………………….. 13
8. PERSON IN CHARGE…………………………………………………………………………………………………. 14
9. SUPPORTING DOCUMENT………………………………………………………………………………………… 15

3
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

1. EXECUTIVE SUMMARY

The purpose of this document is to demonstrate the step-by-step procedure of RET

setup and configuration in BTS level SW SRAN18SP in Indosat network, using new Antenna
(Combi/Comba tripleband or Mobi_pentaband) or using exsiting Antenna (same procedure)

 Involved NE:

o eNB ( BTS LTE1800 )

o NodeB ( BTS U900 )
o BTS GSM 900
o NodeB ( BTS U2100)

 Pre-requisite:

1. Combi/Comba_Tripleband
Default setting:
Electrical = 2 degree
Mechanical = 2 degree
Min degree = 0 degree
Max degree = 10 degree

Figure 1. Degree electrical range antenna tripleband

2. Mobi_Pentaband
Default setting:
Electrical = 2 degree
Mechanical = 2 degree
Min degree = 0 degree
Max degree = 10 degree

Figure 2. Degree electrical range antenna pentaband

4
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

3. Incase use existing antenna

Take awareness on existing antenna feature with support RET or not, also take a
consider SCF creation.
How to read and record existing RET setting:
• capture it from BTS Manager.
• Climb tower and see antenna sector, check the antenna tilt road.

Figure 3. physical check antenna tilt road

Some remarks RET for existing antenna on the table below :

Antenna Type RET Remarks
RVVPX310R-BTQ support independent with manual override on all arrays
RV4PX310B1Q support independent with manual override on all arrays
RVVPX310B1Q support independent with manual override on all arrays
NNPX310R-4P not support
K730378 not support
CVVPX310R-BT1 support independent with manual override on all arrays
K739630 not support
VM65-7_T0 not support
K739650+XXGG85-17-TVV not support + not support
K739650 not support
K739630+K739650 not support + not support
RVVPX310R-BTQ support independent with manual override on all arrays
RV4PX310B1Q support independent with manual override on all arrays
RVVPX310B1Q support independent with manual override on all arrays
NNPX310R-4P not support
K730378 not support
CVVPX310R-BT1 support independent with manual override on all arrays
K739630 not support
VM65-7_T0 not support
K739650+XXGG85-17-TVV not support + not support
K739650 not support
K739630+K739650 not support + not support

5
 MOP of setup RET in SRAN 18SP

2. Setup RET band 900 (R1)

Instructions on how to setup RET band 900, motor RET is R1 using BTS Manager, based on information table

Antenna model Antenna serial number Site ID Basestarion ID Sector ID

Combi/comba 00CB1820000424 16SBS005 PEMANGKAT 1-900

RET Location Remarks RET ID RETU Naming : ALD ID RF Module type Antenna Line Number
served antenna line Antenna line
device
00CB1820000424- Sector-1 RET - 1 RETU - 1 ALD - 1 FXDA, FXDB RMOD - 1 : ANT1 … ANT6 | RMOD - 2 : ANT7
R1 … ANT12

1. Go to commissioning wizard

2. Please see setting gear for R1, than Click. Than take look in setting Antenna Line Device  Antenna Line Device RET
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

click

3. Major setting in band 900 for RET-1 must be setup is : control protocol, controlling port, and DC power source

 Control protocol = AISG 2.0 _for protocol antenna line device R1 for band 900
Auto-detect

 Controlling port = RMOD_1/ANTL_1 (FXDA) or (FXDB) _ make sure physical port antenna (+45) connected to port ANT_1 (TxRx)

R1 for band 900

Auto-detect

7
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

OSS will remotly send degree of electrical tilt_signal go to port (+45) in antenna, make sure jumper connection from ANT_1 (TxRx) at RF
module FXDA or FXDB are correct and properly

 DC power source = RMOD_1/ANTL_1 (FXDA) or (FXDB) _ make sure physical port antenna (+45) connected to port ANT_1

Motor RET running using power dc feed/source from antenna port (+45), make sure jumper connection from ANT_1 (TxRx) at RF module
FXDA or FXDB are correct and properly

8
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

2.3 Setup RETU band 900 (RETU-R1)

Instructions on how to setup RETU band 900 (R1), for served antenna line ANT_1, ANT_3, ANT_5 of FXDB_1/FXDA_1 and served antenna line
ANT_7, ANT_9, ANT

1. Major setting in RETU for RET-1 must be setup is : served antenna lines, Base station ID, Sector ID, Angel

 Served antenna lines, for define antenna connection band 900 in part RF module (FXDA or FXDB) sides

The More antenna lines number is described number of RF module (FXDA or FXDB) installed in the site BTS.

In this capture means: RMOD-1/ANTL-1 (FXDA number-1) while RMOD-2/ANTL-7 (FXDA number-2) is correspondent with band 900
RETU-R1.

Served antenna lines : RMOD-1/ANTL-1 (FXDA) | RMOD-2/ANTL-7

(FXDA)
Each antenna line can exist only on one antDNList in the BTS.

9
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

 Base station ID : GDULT_PEMANGKAT_PL_XYX _ is define the site Name of BTS

Site name

 Sector ID : 1-900 (sector 1), or 2-900 (sector 2), or 3-900 (sector 3) _ for this identification must follow Standard Naming RET Indosat.
Please see supporting document for more details

The sector ID must have corelation with serial number antenna, the input parameter in site ID must correct with actual antenna
insalled is in the right sector, to cross check by validating serial number antenna.

Sector ID

 Angels: is consisting of degree value refer to RF data planning and antenna tilt range capability as of antenna specification

10
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

Angle = electrical tilt degree value as per RF data planning, range value : 0 – 90 degree. Default electrical tilt 2 degree

Mechanical angle = is value set of mechanical tilt bracket antenna as of actual install. Default mechanical tile 0 degree

Min – Max Angle = is range electrical tilt capability antenna as of specification. value of range electrical tilt between 0 – 10 degrees

For the other RET unit : Y1, Y2_band 1800, 2100 or Y3, Y4 (antenna pentaband) is the same procedure as described in RET unit R1

Antenna model Antenna serial number Site ID Basestarion ID Sector ID RET Location Remarks
Combi/comba 00CB1820000424 16SBS005 PEMANGKAT 1-900 00CB1820012820-R1 Sector-1
RET IDCombi/combaRETU Naming :
00CB1820000424 ALD ID16SBS005 RF Module type
PEMANGKAT 1-1800 Antenna
00CB1820012820-Y1 Line NumberSector-1
served antenna line Antenna line device
Combi/comba 00CB1820000424 16SBS005 PEMANGKAT 1-2100 00CB1820012820-Y2 Sector-1
RET - 1 RETU - 1 ALD - 1 FXDA, FXDB RMOD - 1 : ANT1 … ANT6 | RMOD - 2 : ANT7 … ANT12
Combi/comba 00CB1820000325 16SBS005 PEMANGKAT 2-900 00CB1820000325-R1 Sector-2
RET - 2 RETU - 2 ALD - 1 FXDE RMOD - 1 : ANT1 … ANT6 | RMOD - 2 : ANT7 … ANT12
Combi/comba 00CB1820000325 16SBS005 PEMANGKAT 2-1800 00CB1820000325-Y1 Sector-2
RET - 3 RETU - 3 ALD - 1 FRGP, FRGF, FRGU RMOD - 1 : ANT1 … ANT6 | RMOD - 2 : ANT7 … ANT12
Combi/comba
RET - 4 RETU - 400CB1820000325 ALD - 216SBS005 PEMANGKAT
FXDA, FXDB 2-2100 RMOD 00CB1820000325-Y2
- 1 : ANT1 … ANT6 | RMOD - 2Sector-2
: ANT7 … ANT12
Combi/comba
RET - 5 RETU - 500CB1820000400 ALD - 216SBS005 PEMANGKAT
FXDE 3-900 RMOD 00CB1820000400-R1
- 1 : ANT1 … ANT6 | RMOD - 2Sector-3
: ANT7 … ANT12
Combi/comba
RET - 6 RETU - 600CB1820000400 ALD - 216SBS005 PEMANGKAT
FRGP, FRGF, FRGU 3-1800 RMOD 00CB1820000400-Y1
- 1 : ANT1 … ANT6 | RMOD - 2Sector-3
: ANT7 … ANT12
RET - Combi/comba
7 RETU - 700CB1820000400 ALD - 316SBS005 PEMANGKAT
FXDA, FXDB 3-2100 RMOD 00CB1820000400-Y2
- 1 : ANT1 … ANT6 | RMOD - 2Sector-3
: ANT7 … ANT12
RET - 8 RETU - 8 ALD - 3 FXDE RMOD - 1 : ANT1 … ANT6 | RMOD - 2 : ANT7 … ANT12
RET - 9 RETU - 9 ALD - 3 FRGP, FRGF, FRGU RMOD - 1 : ANT1 … ANT6 | RMOD - 2 : ANT7 … ANT12

11
 MOP of setup RET in SRAN 18SP
_________________________________________________________________________________________________

12
 MOP of setup RET in SRAN 18SP

3. SUPPORTING DOCUMENTS

No Document description Status File

Standard naming RET unit Indosat Available / Yes

1. RETU related to
SON tools_v7.pdf

RET unit naming antenna Combi/Comba, Mobi Available / Yes

2. naming Site ID_RET
Combi Mobi Isat_v1.xlsx

LTE_SRAN_RET_management_in_Configurator Available / Yes

3 LTE_SRAN_RET_man
agement_in_Configurator.pdf