Scribd
Upload
241 views2 pages

Armox 600T: General Product Description

Armox 600T

Uploaded by

ehudingram6535
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
241 views2 pages

Armox 600T: General Product Description

Armox 600T

Uploaded by

ehudingram6535
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Data sheet 197 Armox 600T 2017-04-19

Armox 600T

General Product Description


Extra-high-hardness armor with very good resistance against penetration.
Armox® 600T is used as an add-on protection plate or where weight is critical.
Armox 600T is available in thicknesses between 4 and 20 mm with a guaranteed hardness range of 570‑640 HBW.
Benefits of Armox 600T include:
• Market-leading steel protection
• Superior workshop properties
• Wide product range – optimized solutions
• Perfect hardness/toughness balance, for combined penetration and blast protection
• Expertise in ballistic protection from SSAB
 
Armox 600T is not intended for further heat treatment.
 
 
Dimension range
Armox 600T is available in thicknesses between 4.0 and 20.0 mm. Other dimensions to be agreed with SSAB.

Mechanical Properties
Plate thickness Hardness Charpy-V 1) 10x10 mm test specimen2) Min.
(mm) (HBW)
4- 20 570- 640 12 J /-400C
1)
Average of three tests. Transverse to rolling direction. Single value min. 70% of specified average.
2)
For plate thicknesses under 12 mm sub-size Charpy-V specimen are used. The specified minimum value is then propotional to the specimen cross-section.
 

Mechanical Testing 


Brinell hardness test according to EN ISO 6506-1 on each heat treatment individual.
Charpy impact test according to EN ISO 148 on each heat and thicknesses from 6 mm.
 
Ultrasonic testing
According to EN ISO 10 160 Class E3 S3.

Chemical Composition (ladle analysis)


C *) Si *) Mn *) P S Cr *) Ni *) Mo *) B *)
(max %) (max %) (max %) (max %) (max %) (max %) (max %) (max %) (max %)
0.47 0.70 1.00 0.010 0.003 1.5 3.00 0.7 0.005
The steel is grain-refined. *) Intentional alloying elements.
 
Tolerances
More details are given in SSAB´s brochure 41-General product information Strenx, Hardox, Armox and Toolox-UK or on www.ssab.com.
Thickness
Heavy Plate
Plate thickness Tolerances
(mm) (mm)
4.0- 12.9 - 0.0 / + 0.6
13.0- 19.9 - 0.0 / + 0.8
20.0 - 0.0 / + 1.0
 
Data sheet 197 Armox 600T 2017-04-19

Length and Width


According to SSAB´s dimension program.
• Tolerances conform to EN 10029 or to SSAB´s standard after agreement.
• Dimensional tolerances for plate with mill edge according to special agreement.
 
Shape
Tolerances according to EN 10 029.
 
Flatness
Tolerances according to SSAB´s flatness tolerances which are more restrictive than EN 10029 Class N (steel type L).
 
Surface Properties
According to EN 10 163-2 Class B Subclass 3.
 
Delivery Conditions
The delivery condition is QT (Quenched and Tempered). Delivery requirements can be found in SSAB’s brochure 41-General plate product infor-
mation Strenx, Hardox, Armox and Toolox-UK or www.ssab.com.

Fabrication and Other Recommendations


Welding, bending and machining

For information concerning welding and fabrication, see SSAB´s brochures on www.armoxplate.com or consult Tech Support, techsupport@
ssab.com.
Armox 600T is not intened for further heat treatment. If Armox 600T is heated above 170 °C after delivery from SSAB no guarantees for the
properties of the steel are given.
Nitriding or surface coating may be carried out if the temperature is below 170 °C.
Appropriate health and safety precautions must be taken when welding, cutting, grinding or otherwise working on the product. Grinding, espe-
cially of primer coated plates, may produce dust with high particle concentration.

Contact Information
www.ssab.com/contact


The English version of this document shall prevail in case of discrepancy. Download the latest version of this document at www.ssab.com
SSAB, Strenx, Hardox, Docol, GreenCoat, Toolox, Armox, Ramor, Domex, Laser, Raex, Duroxite are trademarks owned by the SSAB group of companies.

You might also like