Internet Controller E17 with

3G and WiFi Embedded

Instruction Manual

Ver1.0 SYS/C3-0002001027
 Internet Controller E17 with 3G and WIFI Embedded

Overview
Update Record..........................................................................Ⅰ

Statement .................................................................................Ⅱ

E17 Operational Flowchart ....................................................Ⅲ

Chapter 1: Introduction to Hardware

1.1 Introduction to E17 .....................................................................................1

1.2 Diagram of E17 Control Card Interface ..............................................3

1.3 Control Card Connection..........................................................................8

1.4 Correct Connection of the HUB..............................................................9

1.5 Correct Connection Method of Flat Cable.......................................12

1.6 Connecting Method of E17 Control Card and Receiving Card...16

1.7 Power Supply to the Control Card.......................................................18

1.8 Connection between Control Card and Computer.........................19

Chapter 2: Configure Parameters of LED Display

2.1 Software Instruction and Operation Procedure..............................21

2.2 Method of Existed Parameters..............................................................24

2.3 LED Screen Smart Setup Wizard ..........................................................30

2.4 Cascading Settings....................................................................................43

2.5 Effect of Micro Adjustment....................................................................48

2.6 Width and Height Pixels for the LED Sign.........................................50

 Internet Controller E17 with 3G and WIFI Embedded

2.7 Web Server Configuration......................................................................52

2.8 WIFI Configuration...................................................................................40

2.9 3G Configuration.......................................................................................42

2.10 FAQ and Solutions...................................................................................60

2.11 Transfer Controller from China AIPS to Foreign AIPS..................62

2.12 Synchronizing Hardware Version.......................................................64

2.13 Upgrade Hardware Version for Controllers....................................68

2.14 Software Upgrade for Controllers......................................................70

2.15 Software Uninstall...................................................................................76

Chapter 3: AIPS Cloud Platform System

3.1 Introduction to AIPS Program Release Cloud Platform................78

3.2 AIPS Cloud Platform Account and Log in..........................................80

3.3 AIPS Cloud Platform Overview..............................................................83

3.4 Terminal Alias Modification....................................................................85

3.5 Control Card Parameter Backup............................................................86

3.6 Time Zone Settings....................................................................................87

3.7 Simple Program Production and Release..........................................90

END
Update Record

Version Date Remark

Ver1.0 2017-07-01 The first version

Statement

Dear customers, thanks for choosing Shanghai XIXUN SYSOLUTION LED

control system for your devices, this document will help you learn to how to use

control cards. Please call 400-608-6499 or send email to [email protected] if

meet any problems or have any suggestions, we will feedback you timely.

Copyright

Copyright of this document belongs to Shanghai XIXUN SYSOLUTION LED,

without the written permission of SYSOLUTION, any unit or individual will not be

able to copy or extract the contents of this document, rights reserved.

Brand

is the registered trademark of Shanghai XiXun SYSOLUTION LED

Security Statements

To avoid possible risk, please operate this device as instructed, please contact

our technical support and leave the maintenance work to expert if the device is br

eakdown.

Danger-High voltage: Working voltage for this device is 4.8~5.5V DC

Ground connection: This device need to connect to ground by power

cable, please make sure the ground connection is good.

EMI: Magnet, motor and transformer.

Damp proof: Please put this device in dry and clean environment and

disconnect the power connection immediately if this device get liquid on

it.

Please put this device away from the inflammable and explosive

dangerous goods

Avoid liquid, metal chip invading into the inner of this device, or it may

cause accident.

Please install socket near the device and easy to reach.

 Internet Controller E17 with 3G and WIFI Embedded

E17 Operational Flowchart

The Application of Personnel

This document introduces the use and setup steps of Android controller E17,

provides guidance to users and technical personnel who use E17 for the first time.

Operational Flowchart
 Instruction manual For Internet Controller E17

1.1 Introduction to E17

With the growth of outdoor digital media market, LED display has its larger

proportion on the market with its unique advantages. Many advertisers and media

companies are eager to have a perfect outdoor digital LED system solutions. For

this market, Shanghai XiXun SYSOLUTION LED announced new product to meet the

market demands----E17 (Internet controller E17 with 3G and WIFI embedded)

E17 Controller

www.sysolution.net

1
 Instruction manual For Internet Controller E17

E17 Control System Industrial Application Solution

www.sysolution.net

2
 Internet Controller E17 with 3G and WiFi Embedded

1.2 Diagram of E17 Control Card Interface

E17 is featured with powerful functions, and pixels it can support are much

bigger than other conventional asynchronous control card. It also has many

functional interfaces. Please see the diagra m below to get a clear understanding

(Unlabeled area is blurred out)

Interface specifications are as follows:

 Power Ports: all the Xixun control cards use standard 5V DC input power

supply, please pay attention to the positive and negative electrode when

www.sysolution.net

3
 Internet Controller E17 with 3G and WiFi Embedded

connecting power supply;

USB Dial Switch:

State A: set the left switch(switch 1) to “OFF(down)”, set right switch(switch 2) to

“ON”, now you can use U-disk to update programs, read back, or load parameters

of control card, and so on.

State B: set the left switch(switch 1) to “ON”, set the right witch(switch 2) to

“OFF(down)”, now you can USB debug line for debugging (Generally used for

secondary development).

 USB Port: it is used for connecting the U disk device to update the program,

read back/input control card parameters, etc;

 Ethernet Port for Receiving Card: cascading all series of Sysolution receiving

cards.

 Temperature: it is used for connecting temperature sensor to monitor the

external environment temperature;

 Smoke: it is used for connecting smoke sensor to monitor the smoke in the

box;

www.sysolution.net

4
 Internet Controller E17 with 3G and WiFi Embedded

 Light: it is used for connecting light sensor to monitor the external

environment brightness,

 Humidity: it is used for connecting humidity sensor to monitor the humidity

around.

 Fan: monitoring the power of fan;

 Power Voltage Detector: it is used for connecting the power supply and

monitor the state of the relevant power supply;

 Expand Serial Port: reserved serial port;

 Cabinet Door Detector: it is used for connecting open and close induction

sensor to monitor switch state of the screen cabinet;

 WIFI Dial Switch:

A: set the top switch (switch 1) to “OFF” (the left side), control card will

switch into AP mode, release a WIFI hotspot(named by control card serial number).

For example, if the serial number of control card is E17-716-00159, users can search

this WIFI hotspot named by serial number E17-716-00159 via wireless devices

(laptop or mobile phone). After connecting this hotspot, use Detector software to

configure modules or screens parameter (Default WIFI Password: 12345678).

B: set the top dial to “ON” (the right side ), control card will switch into

WIFI/3GAP mode, set WIFI hotspot name and password so that E17 will get access

to Internet. If want to use the E17 as a hotspot, then please set SSID and password

www.sysolution.net

5
 Internet Controller E17 with 3G and WiFi Embedded

in Detector software. When plugged the 3G/4G SIM card in, then E17 will get access

to Internet through 3G/4G data flow.

 SIM Slot: it is used to insert the 3G phone card to provide Internet for E17 to

remote control(Optional);

 TEST: it is used to test whether the control card matches the LED screen and

resume the control card to default setting;

 RTC Clock Battery: it is power supply for clock chip of the control card, if the

control card time displays abnormal, please check button battery voltage is

normal or not(normal voltage should be 3.3V);

 HUB Connector(two ports): standard 50PIN interface for connecting to the

HUB of general model;

 TF Slot: it is used for connecting TF memory card to expand E17 storage

capacity;

 WIFI Antenna: it is used for connecting Sysolution signal antenna, thereby

ensuring the normal use of WIFI function (if use WIFI, the signal antenna must

be connected);

 Microphone Input: it is used for connecting the sound of microphone speech;

 GPS Antenna: it is used for connecting the special GPS antenna, so as to

ensure the normal use of GPS function (if use GPS function, GPS antenna must

www.sysolution.net

6
 Internet Controller E17 with 3G and WiFi Embedded

be connected);

 Audio Output: it is used for connecting such as Voice Box to play sound;

 3G Antenna: it is used for connecting Sysolution special signal antenna, so as

to ensure normal use of 3G function (if use 3G function, the signal antenna

must be connected);

 Power: it is used to display the operation status of the control card, uniform

flashing indicates that the control card works normally;

 RUN: it is used to display the operation status of the control card, uniform

flashing indicates that the control card works normally;

 Alarm: it is used to display the operation status of the control card, the

indicator light is off if operating status is good, when upgrading, U-disk import,

or operating abnormally, the indicator light will flicker or keep bright ;

 Internet: it is used to display the communication status, as control card is

connected to the computer network via 3G, uniform flashing indicates that the

communication is normal

www.sysolution.net

7
 Internet Controller E17 with 3G and WIFI Embedded

1.3 Control Card Connection

Y10 control card belongs to the LED asynchronous control system, and it needs

to connect to LED display to realize normal process. Related devices are as follows:

 Y10 control card

 LED module

 Hub/Adapter

 Flat cable of different length

 D10 receiving card

 Cable of different length

www.sysolution.net

8
 Instruction manual For Internet Controller E17

1.4 Correct Connection of the HUB

Y10 control card connects to the LED screen through the hub, and the type of

hub is determined by the LED module. You need to consult the module supplier

about the the type of hub that matches. If you are not sure whether the hub

matches the corresponding module, please refer to the tag marked on the back of

the module:

Tag 1: The type of hub on the back of the module

www.sysolution.net

9
 Instruction manual For Internet Controller E17

Tag 2: Port definition of the LED module.

If it is consistent with the port definition of the hub board, the application is correct.

www.sysolution.net

10
 Instruction manual For Internet Controller E17

If the type of hub plate is defined, next step is to connect hub plate to the port

of E17 50PIN hub. Please note that each pin buckles correspondingly, and the

direction of hub plate gap is toward outside of the control card. As shown below:

www.sysolution.net

11
 Instruction manual For Internet Controller E17

1.5 Correct Connection of Flat Cable

After the Hub is properly connected, it is necessary to connect the control card

with the module through flat cable. In most cases, there is a bayonet at the interface

of the Hub and a module which can prevent the cable from being inversely

connected (shown in the picture below).

www.sysolution.net

12
 Instruction manual For Internet Controller E17

Or keeping red thread of flat cable on top (shown in the picture below).

www.sysolution.net

13
 Instruction manual For Internet Controller E17

In general, an interface on the Hub board corresponds to a row of modules of the

control card, for example, the first interface corresponds to the first row of module,

and the second interface corresponds to the second row of module, the rest can be

done in the same manner.

www.sysolution.net

14
 Instruction manual For Internet Controller E17

www.sysolution.net

15
 Instruction manual For Internet Controller E17

1.6 Correct Connection of E17 Control Card and

Receiving Card

The pixels of single E17 control card is 320x192. If pixels of your entire screen

exceed this range, or the LED device is rental cabinet, you need to choose E17

control card (Sending Card) together with the receiving Card to support the entire

screen.

If the LED screen is a rental cabinet, the number of receiving Cards will be one

less than the number of total boxes (Because E17 card can also support one

cabinet );

If the LED screen is a special cabinet or of other type, please refer to the

following web page to calculate the number of receiving Cards:

http://sysolution.net/getcardssolution/GetCardsSolution.html

E17 control card connects the receiving Cards though cables. It is the same for

the connection between receiving Cards.

The receiving Card needs to be connected to the network port marked with D10.

E17 control card is in series with all receiving Cards. please pay attention to the

connection order. You can simply mark it for later setting, such as: Mark E17 control

card as one, mark the first receiving Card which is connected with E17 card as two,

and so on.

www.sysolution.net

16
 Instruction manual For Internet Controller E17

www.sysolution.net

17
 Instruction manual For Internet Controller E17

1.7 Power Supply to the Control Card

Selection and Connection of Power Supply

XiXun E17 control card only adopts 5V DC power supply, please make sure

the correct power supply output before process, or the control card can’t work

properly or even cause overload damage.

It is also important to make clear about positive and negative electrode of

power and E17 control card when connecting the power supply. The interface

marked with +5V should be connected to positive electrode of power, and

interface marked with GND should be connected to negative electrode of power,

just as shown below:

Then turn on the power, the control card start to run automatically as it

finishes examination. If it works normally the light marked with RUN will flicker

constantly and the light marked with Alarm will be off.

www.sysolution.net

18
 Instruction manual For Internet Controller E17

1.8 Connection between Control Card and Computer

State A: set the top switch (switch 1) to “OFF” (the left side), control card will switch

into AP mode, release a WIFI hotspot(named by control card serial number). For

example, if the serial number of control card is E17-716-00159, users can search this

WIFI hotspot named by serial number E17-716-00159 via wireless devices (laptop or

mobile phone). After connecting this hotspot, use Detector software to configure

modules or screens parameter (Default WIFI Password:12345678)

State B: set the top dial to “ON” (the right side ), control card will switch into

WIFI/3GAP mode, set WIFI hotspot name and password so that E17 will get access to

www.sysolution.net

19
 Instruction manual For Internet Controller E17

Internet. If want to use the E17 as a hotspot, then please set SSID and password in

Detector software. When plugged the 3G/4G SIM card in, then E17 will get access to

Internet through 3G/4G data flow.

Step 1: If you want to set parameters of E17, please make sure WIFI dial switch at

state A.

Step 2: Use laptop (or other wireless devices) search WIFI hotspot named by serial

number of E17 controller, default WIFI password is 12345678, open Detector

software (or open browser input: 192.168.43.1: 3000 at the address bar via other

wireless devices) to do configurations.

This section mainly introduces the connecting method between the control card

and computer. E17 control card need to connect to laptop (or other wireless devices)

via WIFI, please make sure your laptop can support WIFI function and works well.

The wireless devices here means:laptop, tablet, cellphone.

www.sysolution.net

20
 Instruction manual For Internet Controller E17

2.1 Software Instruction and Operation Procedure

LedSet Software:

Software1: Detector (only work with LED android series controller), find your

card automatically, download link for Software:

http://www.sysolution.net/download.html

Software2: WebLedSet(set on web page): Open web page (Google chrome

recommended) and input “card IP address: 3000” at the address bar to enter the

configuration interface.

For example: 192.168.43.1: 3000, Here the card IP address “ 192.168.43.1 ” is

changeable, it should be your LED control card IP address.

For example, in the following screenshot, we input “192.168.43.1: 3000” to enter

the WebSet interface.

Screenshot of Software Interface:

www.sysolution.net

21
 Instruction manual For Internet Controller E17

Steps of configuring LED display module:

Step1. System Version Management (Synchronizing all hardware versions)

Step2. LED Screen Smart Setup Wizard (Smart Setup Wizard--Cascading

Settings--Effect of Micro Adjustment)

Step3. System Common Parameters Settings including web server parameters.

www.sysolution.net

22
 Instruction manual For Internet Controller E17

Steps of Configuring network parameters before publishing programs：

Step1. Log in AIPS platform www.ledaips.com:8888 for foreign customers.

Step2. System Network Server Configuration (Configure web server address,

company ID and internet type WIFI or 3G)

Step3. Log in AIPS platform and publish programs.

www.sysolution.net

23
 Instruction manual For Internet Controller E17

2.2 Method of Existed Parameters

Method1: Copy the parameters to other LED controllers

Copy the correct parameters (including intelligent setup, cascading settings, effect

parameters, data numbers, screen width and height pixels) to other LED controllers

through software. This method could also be applied to multiple LED controllers

within the same local network area.

Example:

E17-715-00507 control card has been setup correctly. Now let’s copy the correct

parameters from this card to other two cards E17-116-01575 and E17-116-01578,

here are steps:

Step1: Plugging all LED controllers in the same local network area, select the card

E17-715-00507 that has been already setup, click“ParameterSetting”, following is

the screen shot:

www.sysolution.net

24
 Instruction manual For Internet Controller E17

Step2: Select“Copy LED Screen and System Parameters to Others”, following is the

screen shot:

Step3: Then go to control cards interface and choose the other two cards or more

cards those need to be setup, click the arrow and into copy function and

result interface, here is the following screen shot:

www.sysolution.net

25
 Instruction manual For Internet Controller E17

Method2: Import and export LED display configuration parameters

Import configuration parameters:

Step1: With correct FPGA parameters, select “ LED Screen Configuration Import

and Export” option, here is the screen shot:

www.sysolution.net

26
 Instruction manual For Internet Controller E17

Step2: Upload the FPGA parameters and select the file, here is the screen shot:

www.sysolution.net

27
 Instruction manual For Internet Controller E17

Step3: There will be a tip message pop up to showing the result, “ Good Job ”

means the parameters have successfully imported to other cards. Here is the screen

shot:

Readback parameters:

Select “Download The Hardware Parameters”and then could readback the correct

parameters from the LED control card, here is the screen shot:

www.sysolution.net

28
 Instruction manual For Internet Controller E17

NOTE: FPGA file including the intelligent setup file, cascading settings file and

effect parameters.

Please refer to: 2.16 Import and Export Backup File Through USB.

www.sysolution.net

29
 Instruction manual For Internet Controller E17

2.3 LED Screen Smart Setup Wizard

Step1: Run Detector software

(if not windows system computer, then write down 192.168.43.1:3000 in web page,

while 192.168.43.1 is the LED card IP address it is changeable, if control card IP

address is 192.168.8.175 for example, then write down 192.168.8.175:30000)

after this, enter the software interface and select the card ID to continue:

Default IP address of E series LED card:192.168.43.1

Default IP address of Y series LED card: 192.168.0.200;

Step2: As shown above, select ”ParameterSetting” enter CardSystem settings, and

then,Select “ LED screen smart setup wizard ” and enter into the LED module

parameters interface, see picture in below:

www.sysolution.net

30
 Instruction manual For Internet Controller E17

Step3: When enter smart setup, a tip message will show up “click ‘yes’ to set the

module, click ‘skip’ to cascading settings”. Normally need to do smart setup for

all brand new controllers. So choose‘Yes’and continue, see screen shots in below:

(If LED sign already display correct images or videos means the controller has been

setup already, so no need do settings again, click ” Skip ” to enter next step

“Cascading Settings” ).

www.sysolution.net

31
 Instruction manual For Internet Controller E17

Step4: If choose “ Yes ” then enter next interface, need to write down exactly

correct parameters for one LED module.

For example, Module width : 64

Module height: 32

Input flat cable number:1

RGB group:2

Decoding type: 138 Decoding

All those information should be known before doing this, if do not know then need

to consult the LED module suppliers in advance.

After done here, please click Next Step :

www.sysolution.net

32
 Instruction manual For Internet Controller E17

Step5： Need to choose status one, watch the module status, choose status two,

watch module status, find out which status is on, which status is off. After done,

click Next Step:

Step6: Need to choose status one, watch the module status, choose status two,

watch module status, find out which status is bright, which status is dark. After

done, click Next step:

www.sysolution.net

33
 Instruction manual For Internet Controller E17

Step7: Need to choose colors, color1, color2, color3 and color4. After done, click

Next step:

Step8: Watch LED module and find out how many bright lines within one LED

module, also need to figure out how many lines between the bright lines.

If only one bright line in one module, then choose 0 or only one bright line.

If whole LED module all bright, then also choose 0 or only one bright line.

After done, click Next step.

www.sysolution.net

34
 Instruction manual For Internet Controller E17

For example, this means there is one bright line.

So choose interval line is 0 or only one bright line.

www.sysolution.net

35
 Instruction manual For Internet Controller E17

Step9: Normally will see two bright pixels, find out which row it is. Click the correct

position in the software.

For example, now there are two bright pixels in the top row, so start clicking in the

row1 in the software.

Then the two pixels will move, just following the bright pixels movements and click

the correct position in the software.

www.sysolution.net

36
 Instruction manual For Internet Controller E17

After done, remind message will pop up and ask you go to next step, see screen

shot in the below:

www.sysolution.net

37
 Instruction manual For Internet Controller E17

Step10: Normally will see one flashing pixels in the module, also need to find its

position, in which row and which column and then click in the software correctly,

When click the first pixels correctly in the software, the second pixels will show up

immediately, need to click in the software for the second pixels either, then

third,.......

Just need to watch the pixels movements in the module and click in the software

correctly.

www.sysolution.net

38
 Instruction manual For Internet Controller E17

After done, the module will show bright lines

www.sysolution.net

39
 Instruction manual For Internet Controller E17

Meanwhile, the tip message will pop up to ask you go to next step after

confirmation,

www.sysolution.net

40
 Instruction manual For Internet Controller E17

Step11: After done success for last step, at this step, will see correct and complete

slash lines come out from top right to the bottom left, if the slash lines not correct

then need double check above steps again.

www.sysolution.net

41
 Instruction manual For Internet Controller E17

After clicking, go to next step: Cascading Settings

www.sysolution.net

42
 Instruction manual For Internet Controller E17

2.4 Cascading Settings

Write down the cascading setting parameters according to the module information

and receiving cards numbers, see picture in below:

1. The width and height pixels of one module

2. The width and height pixels of receiving card

3. If master card responsible for one screen

4. Vertical and horizontal card number of the whole screen

For example, here:

1. Module width is 32 pixels, and Module height is 16

2. The width and height pixels of receiving card is 128x96

3. Master card responsible for one screen

www.sysolution.net

43
 Instruction manual For Internet Controller E17

4. Vertical card number is 2, and horizontal card number is 2

5. Click the empty blocks according to the receiving cards connection orders, the

first click should be master card, the second click is the first receiving card, and so

on.

If click wrong, please click “Backspace” button and redo it. See picture in below：

The click sequence of cascading setting according to the connection sequence of

receiving cards, As shown below:

www.sysolution.net

44
 Instruction manual For Internet Controller E17

Press “Set” button after confirmation, then watch the screen image correct or not,

if correct, click “Save” button, then cascading setting parameters will be stored in

controller automatically. See picture in below:

www.sysolution.net

45
 Instruction manual For Internet Controller E17

Please look at the screen in below:

www.sysolution.net

46
 Instruction manual For Internet Controller E17

www.sysolution.net

47
 Instruction manual For Internet Controller E17

2.5 Effect of Micro Adjustment

There is an optional function, if LED screen display all good without any problem,

then can omit this step. But if LED screen display with some lines or irregular pixels,

please try these micro adjustment.

① scan clock: range 25MHz-2.0MHz, default is 12.5MHz,higher scan clock higher

refresh rate;

② Effect adjust: range 0-41. When there some shadow pixels or irregular /flashing

lines in the screen, please adjust the effect number, higher numbers means lower

refresh rate;

③ Refresh rate and brightness selection: can leave with default one; there are three

choices including high light lower refresh, middle light middle refresh, low light

high refresh;

④ Gray level: 65536 is default one;

⑤ 16/20：select different types according to the HUB type; need some professional

knowledge of hub;

⑥ Lock phase: there are 5 levels for different types of LED module.

When LED screen display irregular pixels or broken image, could try this function;

⑦Blanking: 400 is default;

⑧ Phase: 2 is default.

Note: no need to change or adjust for default parameters.

www.sysolution.net

48
 Instruction manual For Internet Controller E17

See screen shot of software interface:

Need to click “Save” button after adjusting all parameters and download and

save the backup file in the computer. The backup file name is *.FPGA.click Next step

to finished. See picture in below:

www.sysolution.net

49
 Instruction manual For Internet Controller E17

2.6 Width and Height Pixels for the

System Common Parameters Settings

Please select “System Common Parameters Settings” in the main menu and enter

the following interface:

www.sysolution.net

50
 Instruction manual For Internet Controller E17

1. Control card language: Chinese or English; control card time zone: choose your

local time zone;

2. Width and height pixels for the whole LED sign; press save;

3. Volume settings: range 0-15. Input the volume number you need or use the

add/reduce button （add 4, reduce 1）;

4. Brightness settings:

Manual brightness: maximum brightness value is 64. Can input the number

directly or use the add/reduce button (add 4, reduce 1);

Automatic brightness: sensor sensitivity, range 0-100; higher sensor sensitivity

then higher degree of accuracy (add 5 reduce 1).

NOTE: all numbers could not exceed the range, or will invalid.

www.sysolution.net

51
 Instruction manual For Internet Controller E17

2.7 Web Server Configuration

Select “System Network Server Configuration” and enter the following interface:

www.sysolution.net

52
 Instruction manual For Internet Controller E17

1. Write down the web server address and company id, press SAVE button.

Normally use www.ledaips.com:888 for foreign customers. Customers should use

the same company ID that registered in the AIPS platform. Pay attention to the

letter case.

2. “ Network status detection ” , press this button and detect the current

network connection status and signal strength. See picture in below：

www.sysolution.net

53
 Instruction manual For Internet Controller E17

www.sysolution.net

54
 Instruction manual For Internet Controller E17

2.8 WiFi Configuration

1. WIFI settings: enable “WiFi switch” and click “Scanning WiFi”, select the WiFi

name and write down the WiFi password. Click “Save”.

2. After set the WiFi parameters, set the top dial of“WIFI Dial Switch” to state B

(number“3”), wait for the control card access WiFi automatically.

www.sysolution.net

55
 Instruction manual For Internet Controller E17

3. Wait for about 5 minutes, controller will come online. Please watch the

“Internet” light, if it flashing regularly means online success, go to AIPS platform

and check it.

NOTES:

1. If could not scanning the WiFi, please try to turn on/turn off Software or WiFi

Switch.

2. If controller can’t get access to internet through WiFi, please double check the

steps below:

A. WiFi antenna plug correctly.

B. WiFi password is correct or not.

C. If the Wireless router being accessed too many terminals?

D. Try another WIFI hot spot.

www.sysolution.net

56
 Instruction manual For Internet Controller E17

2.9 3G Configuration

1. Choose correct country code, 460 is Chinese code for example (If do not know

your country code, please click Network status detection button and check IMSI

number, the first 3 numbers are the country code).

2. APN access point: China Unicom for instance. If do not know the APN, please

consult your local SIM card provider;

www.sysolution.net

57
 Instruction manual For Internet Controller E17

3. After choose correct APN access point, the APN will show up automatically, if has

user and password, please write down and press SAVE. If no user and password,

leave it empty.

4. After save 3G parameters, waiting for about 5 minutes, please check if card online

in AIPS platform. “ Internet ” light will flashing fast for dialing up then flashing

regularly means get online success.

NOTES: If controller can’t get online success, please checking following things:

A. 3G antenna has plugged correctly?

B. APN is correct or not？

D. SIM card has activate? SIM card has enough money and 3G data service?

E. Check 3G signal at least 13 and above? Click Network status detection to check

3G signal.

www.sysolution.net

58
 Instruction manual For Internet Controller E17

Here is the log in interface of AIPS platform:

For more information, please refer to Chapter 3: AIPS Cloud Platform System

www.sysolution.net

59
 Instruction manual For Internet Controller E17

2.10 FAQ and Solutions

1. Can’t detect E17 controller through software?

Answer: Please check whether the laptop is connected to the hotspot of E17;

restart Detector.

2. Area of the LED sign which is connected to D10 show nothing on it?

Answer: Please go to “system version management” and click

“synchronization Hardware Version” to make the firmware version of D10 match

with it of E17, after the synchronization, screen will show message properly. P.S. It

may take some time if you have several D10 connected.

3. Cannot set the controller by “LED screen smart setup wizard”?

Answer: ①Please check the drive IC and Decoding chip of the module and

contact us to get upgrade firmware if the chips are special.

②You cannot set the controller if it is under upgrade or synchronization. Please

check the “Alarm” indicator on controller, it means the controller is be upgraded

or synchronized if this indicator is flashing very fast, please wait patiently till

upgrade or synchronization is finish.

4. ”RUN” indicator on the controller is off and LED screen show nothing?

Answer: Please check the power input of the controller with multimeter,

controller need 5V DV to work normally.

www.sysolution.net

60
 Instruction manual For Internet Controller E17

5. Screen show nothing or several blue squares on it?

Answer: ①Please check the connection between E17 and D10s;

②Please refer to the second answer of question 3.

6. Controller do not come online via 3G?

Answer:

①Please make sure the network cable is off from the controller;

②Please check the antenna is connected to the 3G port of the controller nice

and well;

③Please check the APN you filled in the 3G setting is correct ( You can get the

correct APN from your SIM card carrier);

④Please make sure the SIM card you use is activated and workable;

⑤Please check the 3G signal. You can check it by clicking “Network status

detection” in “system network server configuration”.

www.sysolution.net

61
 Instruction manual For Internet Controller E17

2.11 Transfer Controller from China

AIPS to Foreign AIPS

China AIPS address:www.m2mled.net

Foreign AIPS address:www.ledaips.com:8888

Method 1:

Select “system network server parameter configuration” and then write down

the foreign AIPS address, company ID, press save.

See picture in below:

Method 2:

If controller has already registered in China AIPS and get online. Then go to

config setting-->advanced -->write down foreign AIPS address and the

company ID, click Submit.

Then controller will be transferred to the foreign AIPS platform. But need to

register the company id in advance.

NOTE: The controller need to be online then could transfer.

www.sysolution.net

62
 Instruction manual For Internet Controller E17

www.sysolution.net

63
 Instruction manual For Internet Controller E17

2.12 Synchronizing Hardware Version

1. Select “System Version Management” and enter

www.sysolution.net

64
 Instruction manual For Internet Controller E17

2. Should synchronize hardware version for all receiving cards before configuring;

if change new receiving card also need synchronization hardware version for it.

www.sysolution.net

65
 Instruction manual For Internet Controller E17

3. When pressing this button, a tip message will pop up: synchronous hardware

version successful means the command has sent, now need the receiving cards to

upgrading one by one.

www.sysolution.net

66
 Instruction manual For Internet Controller E17

4. Please do not turn power off for all controllers or do other operations, can watch

the ALARM light in sending card, if ALARM light quick flashing means upgrading,

also can click “Hardware Version Query” to check the result.

www.sysolution.net

67
 Instruction manual For Internet Controller E17

2.13 Upgrade Hardware Version for

Controllers

1. Click “ Upgrade Hardware Version ” and select the correct upgrade file from

computer, normally the file format is .rpd. File name with “m” is for sending card,

“s“ for receiving card.

2. When upload process show 100% means upload success to the controller, then

controller will auto upgrade, each controller may take 1.5minutes. Can also watch

the ALARM light status in the sending card, if quick flashing means still upgrading,

when ALARM light off, means done.

www.sysolution.net

68
 Instruction manual For Internet Controller E17

After that, click “Hardware Version Query” to check result.

www.sysolution.net

69
 Instruction manual For Internet Controller E17

2.14 Software Upgrade for

Controllers

All of software versions can be upgrade for controllers, if customized own software,

need compress with password 888.

1. Xixun software upgrade

Method 1: Online Update

Log in AIPS platform, select the terminal, click “Update Online”,

Click the new version and “Send “ to upgrading

www.sysolution.net

70
 Instruction manual For Internet Controller E17

Can see upgrading process and status, after success, means upgrade has done

Click “Query Terminal State” to get all software versions for controllers；

Method 2：Offline Update

Log in AIPS platform, go to “Update Online”, click the download icon to

download the new version file to computer.

www.sysolution.net

71
 Instruction manual For Internet Controller E17

Then go to WebLedSet, detect the controller IP, go to “ System Version

Management” and choose “Upgrade Software Version”, select the new version

file, it is a zip file, no need unzip.

Upload 100% and wait another one minute and then a upgrade success tip

message will pop up;

www.sysolution.net

72
 Instruction manual For Internet Controller E17

NOTE: even saying upload file success, need wait another 1-2 minutes for software

installation.

Click “Software Version Query” to check the result:

www.sysolution.net

73
 Instruction manual For Internet Controller E17

2. Third Party Software Upgrade

Customized own APK software, compress into zip file with password 88888888

Click third party APK application and then click upgrade software version, then

select the zip/rar file.

Please wait another 1 -2 minute after uploading 100%, when upgrade success, even

show success, need waiting for software installation, this will take 1-2 minutes.

www.sysolution.net

74
 Instruction manual For Internet Controller E17

Refresh this interface and click drop down box besides software uninstall button

will see all apk applications in controller, see picture in below；

www.sysolution.net

75
 Instruction manual For Internet Controller E17

2.15 Software Uninstall

Click drop down box and choose the apk application that need to be uninstalled,

then click “Software Uninstall” button, see picture in below:

After done this, the uninstall result will pop up.

www.sysolution.net

76
 Instruction manual For Internet Controller E17

www.sysolution.net

77
 Instruction manual For Internet Controller E17

3.1 Introduction to AIPS Program

Release Cloud Platform

As the first solution for led display industry, Xixun AIPS program release

cloud platform can be used in various systems timely, with powerful features but

easy steps, customers will take over it quickly. Please follow the instructions to use

our AIPS platform correctly.

For the terminal that access in the AIPS for the first time, please follow the

steps：

1. Modify the terminal surname,

2. Backup for the terminal,

3. Set the timezone,

4. Simple program made and send.

For details, please refer to section 3.4, 3.5, 3.6 and 3.7.

www.sysolution.net

78
 Instruction manual For Internet Controller E17

www.sysolution.net

79
 Instruction manual For Internet Controller E17

3.2 AIPS Cloud Platform Account and

Log in

Based on web page program software, can run AIPS platform in any devices

including laptop, smart phone, pad and so on. Please use Google Chrome as

recommended to remote control the LED displays.

 www.ledaips.com：8888

(Please use the same AIPS platform address that set in controller)

After open the correct AIPS platform, please write down the administrator ID

and password. Click Log in and then enter the interface.

www.sysolution.net

80
 Instruction manual For Internet Controller E17

If has not register in AIPS platform, please click register and write down details then

will get the verify email, go to administrator email box, please click the link to finish

the verification.

www.sysolution.net

81
 Instruction manual For Internet Controller E17

www.sysolution.net

82
 Instruction manual For Internet Controller E17

3.3 AIPS Cloud Platform Overview

AIPS platform integrates various features, following picture shows the main

functions of it:

There are functions label menu and operations menu totally, when click

different label will have different operation menu. When under “Terminal” label,

will show all terminals including detailed information and all operations icon.

Terminal: Show all terminals under this account with detailed information and

all corresponding operation buttons;

Media: Download, upload and check all media files under this account, those

media files are also the program materials;

Program: Includes various types of program, can add simple and advanced

program, select the materials and make the programs for led display;

www.sysolution.net

83
 Instruction manual For Internet Controller E17

Check Task: Check all operations for controller with state;

Log: Includes user log, operation log, fault log and alarm report;

GPS Task: Especially for led vehicles or led taxi top signs, switching programs

according to device’s locations (longitude and latitude);

User: Can manage all sub-users accounts;

Services: For administrator accounts only, to get the player record of controller

per day, per week or per month.

www.sysolution.net

84
 Instruction manual For Internet Controller E17

3.4 Terminal Alias Modification

In order to manage all terminals efficiently and easily, please modify the alias

for terminals when reports to the AIPS platform for the first time.

Default Alias name of terminals is “noname”.

Select the terminals then go to Config settings-->set-->terminal alias, write

down the new alias and press submit, will see the operation result then. Also click

“Query Terminal State” to check the Alias.

www.sysolution.net

85
 Instruction manual For Internet Controller E17

3.5 Control Card Parameter Backup

We strongly recommend all customers to backup all terminals for future

maintenance, AIPS platform will store the backup file forever, here are steps:

Log in AIPS platform, enter Terminal label, then select the terminals those

need to be backup, go to Config Setting-->Backup, press “Backup” button and

then will switch to the Check task interface and show the operation result:

www.sysolution.net

86
 Instruction manual For Internet Controller E17

3.6 Time Zone Settings

If the led display devices not in China mainland, can modify android controller’s

timezone:

Log in AIPS platform, select the terminals, go to Config setting-->set--timezone,

click drop down box and choose the correct time zone then press submit.

www.sysolution.net

87
 Instruction manual For Internet Controller E17

Then go to “Sync setting”and choose Type C for the terminals, and press “Set”

button. When appears green icon means set success.

www.sysolution.net

88
 Instruction manual For Internet Controller E17

Finally go to“Query”,keep selecting the terminals and press Query button, can see

the time zone result, if show correct local time means all settings correct.

www.sysolution.net

89
 Instruction manual For Internet Controller E17

3.7 Simple Program Production and

Release

After done basic settings for terminals, can try the simple program immediately.

Please refer to AIPS instructions for how to make advance programs and other

functions.

Rules of simple program:

1. Simple program materials include images and video (mp4 format only);

2. Simple program display in full screen size;

3. Simple programs display in loop, can adjust the list order manually;

Steps of making simple program:

Prepare the images and videos (mp4 format), upload to media (go to Media-->click

upload media files), select the files and upload. Please refer to AIPS instructions for

details.

www.sysolution.net

90
 Instruction manual For Internet Controller E17

Go to Program label, choose “Add Simple Program” button, then set the correct

width and height pixels, press “OK” then enter the program editing interface.

Program editing interface in below:

www.sysolution.net

91
 Instruction manual For Internet Controller E17

Choose the images and videos from the media list and then click the blue add icon

before each media file, click the small image to preview it. Can adjust the media file

up and down by clicking icons. After done this, write down the simple program

name and save it. After save, it will jump to the “Program” function label interface,

see picture in below:

Will see program name in the upside, click the “Create Task Quickly” button and

then jump to the “terminal” function label.

www.sysolution.net

92
 Instruction manual For Internet Controller E17

Please select the terminals that need be published and click “program task” tool,

find the program task just created, click Send button and watch the sending

progress.

After sending success, will jump to “Check task” interface automatically, will show

the process of the sending, when achieve 100%, program will be display in led

screen automatically.

www.sysolution.net

93
 Instruction manual For Internet Controller E17

Simple program made and send operations finished.

www.sysolution.net

94
 Instruction manual For Internet Controller E17

END

This is all about the E17 controller system settings, hope that could help you to

use our products with those instructions.

Thanks again for choosing Shanghai XiXun SYSOLUTION LED control system

for your devices. Please call 400-608-6499 or send email to [email protected]

if meet any problems or have any suggestions, we will feedback you timely.

Please visit our English website: www.sysolution.net to get more solutions and

English manuals. It is our honor to cooperate with you and truly to make mutual

benefit for future.

Make LED display be more Intelligent!

Shanghai XiXun Electronics Co., Ltd

August, 2017

95