Mfg.

Representative: Date: Page __1___ of __3___

Authorized Inspector: Date:
FORM U-1 MANUFACTURER'S DATA REPORT FOR PRESSURE VESSELS
As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1
___________________________________________________________________________________________________________

1. Manufactured and certified by ______ SAUDI ARABIA_______

l(Name and address of Manufacturer)
2. Manufactured for ____________________________Demo Vessel_____________________________
l(Name and address of Purchaser)
3. Location of installation ___________________________________DEMO VESSEL____________________________________
l(Name and address)
4. Type ___________Horizontal___________ ____________Vessel_____________ ______________________
l(Horizontal, vertical, or sphere) l(Tank, separator, jkt. vessel, heat exch., etc.) l(Manufacturer's serial number)
___________N/A___________ _____ ___________N/A___________ __________2019___________
l(CRN) l(Drawing number) l(National Board number) l(Year built)
5. ASME Code, Section VIII, Div. 1 ______2017 Edition_______ __________________ _______________________
l[Edition and Addenda, if applicable (date)] l(Code Case number) l[Special Service per UG-120(d)]
Items 6-11 incl. to be completed for single wall vessels, jackets of jacketed vessels, shell of heat exchangers, or chamber of
multichamber vessels.

6. Shell: (a) Number of course(s) __________1___________ (b) Overall length _________1,0 mm _________
Course(s) Material Thickness Long. Joint (Cat. A) Circum. Joint (Cat. A, B, & C) Heat Treatment
Full, Spot, Full, Spot,
No. Diameter Length Spec./Grade or Type Nom. Corr. Type Eff. Type Eff. Temp. Time
None None
1 590 mm ID 1,00 mm SA-516 70 10 mm 2.5 mm 1 Full 100% 1 Full 100% None None
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Body Flanges on Shells

Bolting
Min Hub How Bolting Washer Washer
No. Type ID OD Flange Thk Thk Material Attached Location Num & Size Material (OD, ID, thk) Material
SA-193
1 WN 590 mm 812.8 mm 90 mm 10 mm SA-105 N Welded Shell 20 - 1-1/4" - -
B7N
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

7. Heads: (a) _____________SA-105 (H.T - N/A)______________ (b) ___________SA-234 WPB (H.T - N/A)____________
l(Material spec. number, grade or type) (H.T. - time and temp.) l(Material spec. number, grade or type) (H.T. - time and temp.)
Location (Top, Bottom, Thickness Radius Elliptical Conical Flat Side to Pressure Category A
Ends) Ratio Apex Angle Hemis. Radius
Min. Corr. Crown Knuckle Diameter Convex Concave Type Full, Spot, None Eff.
(a) Left End 45.97 mm 2.5 mm N/A N/A N/A N/A N/A 812.8 mm N/A Yes S None 100%
(b) Right End 12.7 mm 2.5 mm N/A N/A 2:1 N/A N/A N/A N/A Yes S None 100%

Body Flanges on Heads

Bolting
How Bolting Washer Washer
Location Type ID OD Flange Thk Min Hub Thk Material Attached Num & Size Material (OD, ID, thk) Material
(a) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
(b) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

8. Type of jacket _______________N/A_______________ Jacket closure

_______________N/A_______________
l(Describe as ogee and weld, bar, etc.)
8. If bar, give dimensions; if bolted, describe or sketch ____________________________N/A_____________________________
9. MAWP 1,200 kPa __N/A__ at max. temp _200 °C__ __N/A__ . Min. design metal temp. ___0 °C____ at 1,200 kPa_ .
l(Internal) l(External) l(Internal) l(External)
10. Impact test _______________No (Exempted as per UG-20(f))________________ at test temperature of _____N/A______ .
l[Indicate yes or no and the component(s) impact tested]
11. Hydro., pneu., or comb. test pressure __Hydro. at 1,560 kPa (R8)___ Proof test ________________N/A________________

Items 12 and 13 to be completed for tube sections.

12. Tubesheet _______N/A________ _______N/A________ _____N/A_____ _____N/A_____ ________N/A________

l[Stationary (material spec. no.)] l[Diameter (subject to press.)] l(Nominal thickness) l(Corr. allow.) l[Attachment (welded or bolted)]
________N/A________ ________N/A________ _____N/A_____ _____N/A_____ ________N/A________
l[Floating (material spec. no.)] l(Diameter) l(Nominal thickness) l(Corr. allow.) l(Attachment)
13. Tubes ________N/A_________ ______N/A______ ______N/A______ ______N/A______ ________N/A_________
l(Material spec. no., grade or type) l(O.D.) l(Nominal thickness) l(Number) l[Type (straight or U)]

(07/17)