Cast Iron Regular Pattern - Standard Type AUDCO Lubricated Taper Plug Valve has been successfully used ina variety of services because of its unique in-line maintenance capability. The Plug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluid; this confines corrosion and erosion to less critical areas, Sealing is further enhanced by a specially developed plug sealant charged evenly around the seating surfaces. Plugs from 1'/," are impregnated with a PTFE based anti-friction agent - ‘SUPER LoMu’ which provides greater wear resistance and ensures low consistent operating torque. SUPER LoMu also enhances resistance to seizure, Regular pattern Cast Iron Lubricated Taper Plug ‘Valves are supplied with square stems suitable for ‘wrench operation (MW series). Valves 4" and above can be offered with Light Duty Gear Units (MO series), Valves 6" and above ean be offered FG 2200 Cuton with Heavy Duty Worm Gear Unit (MG series). steel ASTM A216 ‘Wrenches and Gear units should be selected as Ge WCB determined by the service conditions, which | Baking ‘Cathon Stel influence the operating torque. However wrenches Sues 188970220 M07 should be ordered separately whereas gear units. Hex. Serew = ANSEBIS2.1 Hex, Nut: ANSIBIS22 as ordered are installed on the valves and supplied. Valvescan alsobe offered with Carbon Steel Plug | Shim (MWSIMOSIMGS series). Gland Packing Mild Steel, Nickel Plated Rubberised Ashesios ‘Compressed Asbestos ‘As astandard, Cast Iron Valves are supplied with | Gasbet AUDCO 731 Plug sealant which is suitable for most services other than acid solutions and petroleum products, On request, plug sealant from, a wide range offered, can be supplied to suit the nature of service. It is recommended that you sonsult us before selecting the plug sealant for a new service, ‘Valves can be offered with screwed ends and flanged ends to the fallowing standards. Screwed : BSP Tr as per BS21 & NPT as per ANSI/ASME B1,20.1, Flanged : To match flanges drilled to BSIO Table D, F and ANSVASME B16.1, Class 125. Drilling to DIN 2532 PN10 or BS 10 Table E or BS 4504 PN 10 can be offered. Valves can also be offered with undrilled flanges. A familiarity with our Catalogue number is not necessary when specifying our Valves, Provide the following details of the valve to our stributor/Stockist: Size, Type (Standard, Inverted), Line Fluid, Pattern, Materials of construction, Pressure rating, End connection and ‘Type of Operation.TECHNICAL DATA Catalogue No. Miz, MW MWIMWSIMOMOSMGMGS 11 ‘Screwed BSPTY Screwed NPT Flanged BST DY Flanged BST'F Flanged Class 125 | boas DIMENSIONS (mm) E Ti ae Fae Soe ie DN 15] [DN 22] DN 40 | DN 50]| DN 65 | DN 80 |DN 100}N 125|DN 150 [DN 200) EndwEsd Screwed A | 8&9 Fase to Face Flanged B | 1207 raz3 | 241.3 | 304 | 3854 | 393.7 | 4972 Flange diameter BST"D' C | 05.3 165.1 | 1842] 2189 | asso | 2794 [3366 BST 953 1ga2 | 203.2 2794 | 3048 | 368.3 CL 125 1773 | 1905 254.0 | 2794 | 342.9 Flange thickness BST ‘DD wi | it 238 | 54 | 284 BsT Dt wo | 191 2s4 | 24 a a7 tn | it as4 | 284 ‘CIL-1010p of plug z | ms 2o2 | 227 327 | 402 ‘Chubouwm ofbedy BL a6 a | os | 7 | wo | wos vet | ise | 232 WOW diameter G sve | six_| 528 Max. width H | 102 wor | v7 [138] ta9 | 219 | 260 | 289 | 300. ‘Clearance MwMo y | 1s vs | 213 | 249 [ 273 | 30s [ass | aie [| ay | s2e MG aos | 373 ‘CLtwQuadant MOK 29 | m9 | 229 | 229 CILWHIW face MG 30x | a0 CH.twtepolHAVMO Lb. 3e4 | 432 | a7 | 316 MG 619 | 686, Wrench No. jsweue] an [am [an | oe ou st_| ton | wit Sealant stick sire atalala ce}o}jo]felele * For ii MW 12 the wrench willbe 2H * Light duly unt ie recommended for valve size 6 ‘As we continuausly endéavour to improve our products, the data given herein are subject to change. Manufactured by AUDCO INDIA LIMITED 8, MDA Inui Area, Maramaiai Nagar 609-200 Phone: 0411482123 Faxc 001411452607 ‘Acminigtatve OMe Pst Bag 976, Chennal- 600 089 -Phone : 282 2023, Fax: 981 (4d) 282 S0589805 PB No: C1002 pecs recs) Markoted by LARSEN & TOUBRO LIMITED (lrcustinlVabves Section) PO, Box 619, Calcata 700 071 -Ph : 2822001- Fax: s8.2821025 Pst ag 5247, Cheanal 620002 « Ph 8822141» Fak: 44-6520769 PO, Box 6723, New Dat 1001S - Ph: SH 1302 «Fax: i-S429624 PO. Bor 119, Pune 411 001 Ph: e247 Fax: 272-626010 PO, Box 8119, Mumba! 400 051 - Ph 6401092 - Fax: 20-6404Cast Iron Regular Pattern - Inverted Type AUDCO Lubricated Taper Plug Valve hasbeen successfully used in.a variety of services because of its unique in-line maintenance capability. The Plug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluids this confines corrosion and erosion to less critical areas, Sealing is further enhanced by a specially developed plug sealant, charged evenly around the seating surfaces. Plugs are impregnated with a PTFE based anti-friction agent - ‘SUPER LoMu’ which provides greater wear resistance and ensures low consistent operating torque. SUPER LoMu also enhances resistance to seizure. Regular pattern Inverted Cast Iron Lubricated ‘Taper Plug Valves areal supplied with worm gear units (BG series). Valves can also be offered with Carbon Steel Plug (BGS series). Asastandard, Cast Iron Valves are supplied with 2 AUDCO 731 Plug sealant which is suitable for | piyg Cant ron 15210 most services other than acid solutions and Gr. FG 220 or Carbon Steel petroleum products, On request, plug sealant from arTaazis a wide range offered, can he supplied to suit the | Or WR nature of service. It is recommended that you | Botting Studs consult us before selecting the plug sealant fora | ye screwy new service, Hex. Nut Giland Packing Gasket ‘Valves can be offered with flanged ends to the following standards, Flanged : To match flanges drilled to BS1O ‘Table B, F and ANSUASME B16.1 ‘Class 125, Drilling to DIN 2532 PN1O or BS 4504 PN 10 can be offered A familiarity with our Catalogue number is not necessary when specifying our valves. Provide the following details of the valve to ur Distributor/Stockist: = Size = Type (Standard, Inverted) ~ Line ~ Pattem (Regular, Venturi, Short) = Materials of construction (Body, Plug) ~ Pressure Rating = End Connection & Type of OperationTECHNICAL DATA iT Catalogue No. End Connection ala bac | Sa] Seat. BGIVBGSIL Flanged BST ‘D" 100 7 25 165. BGIEBGSUF Flanged BST “F isa 10 2s 16s. BGIWBGSI3 4 300 | 220 10 ns 165 DIMENSIONS (mm) 16" is" DN 400 DN 450 Face w Face 685.8 863.6 Flange BST 'D 5779 ool Diameter BST 'F 609.6 673 Class 125 596.9 6350 Flange thickness 366 Ex CAL, to bostom af body a6 439 HAW diameter 787 787 Clearance 702 703 CA to HUW face 437 529 CAL to tap of HAY 899 992 Sealant stick size E E "AS we continuously endeavour to improve aur preduet, the data given herein are subject change, Manulactured by il AUDCO INDIA LIMITED ost Bag 976, Choral 600.089. Phone: 282 2823 Fax: +91 (441282 sassi9605 PS No: C1008 99 (mpececes CrenO) Marketed by LARSEN & TOUBRO LIMITED (India Valves Section) P.O. Box 619, Calcutta 700 O71 - Ph: 2822901 - Fax: 99-0821005 Post Bag 6247, Chennai 600.002 - Ph: 8620141 - Fax: 44-B620769 P.O, Box 6223, New Deni 110015 - Ph: 8691002 - Fax: 11-5490624 P.O, Boa 119, Pune 411 001. Ph: AD4447 - Fax: 212-800910 PQ, Box 8118, Mumbai 200 051 Ph : 6401232. Fox: 22-6401312Cast Iron Short Pattern - Standard Type AUDCO Lubricated Taper Plug Valve has been successfully used in a variety of services because of its unique in line maintenance capability. The Plug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluid; this confines corrasion and erosion to less critical areas. Sealing is further enhanced by a specially developed plug sealant charged evenly around the seating surfaces. Plugs are impregnated with a PTFE based anti-friction agent - ‘SUPER LoMu’ which provides greater wear resistance and ensures low consistent operating torque. SUPER LoMu also enhances resistance to seizure, ‘Short Pattern Lubricated Taper Plug Valves upto 10” are all supplied with square stems suitable for wrench aperation (LW Series). Valves 6° to 10" can be offered with Light Duty Gear Units {LO Series). Valves 6" and above can be offered with Heavy Buty Worm Gear Unit (LG Series). ‘Wrenches and Gear Units should be selected as determined by the service conditions, which influence the operating torque. However wrenches should be ordered separately whereas gear units as ordered are installed on the valves and supplied. ‘Valves can also be offered with Carbon Steel Plug (LWSJLOSILGS Series) ‘As astandard, Cast Iron Plug Valves are supplied with AUDCO 731 Plug sealant which is suitable for most services other than acid solutions and petroleum products. On request, plug sealant from a wide range offered, can be supplied to suit the nature of service, It is recommended that you ‘consult us before selecting the plug sealant for a new service, Valves ean be offered with flanged ends te the following standards. Flanged : To match flanges drilled to BS1O Table D and ANSIVASME B16.1, Class 125. Drilling to DIN 2532 PN 10 or BS 4504 PN 10.can be offered Valves can also be offered with undrilled flanges. Sizes 6" and above have some holes (refer table) ped on each flange to fucilitate fastening of the mating flanges and require studs of same diameter of the bolts which they replace. The tapping is to UNC threads of class 125 & BST “D’ flanges and ISO metric coarse for PN10 flanges. ‘Name of Part Specification Body Cover de Cast bea Gland 1$210Gr. RG-220 Plug (Cast Iroa IS 210 Gr. FG 220 or ‘Carbon steel ASTM A2I6 Gr WEB Botting Carbon Steel Stags |S 970220 MO? Hes, Seow: ANSIBIB21 Hi ANSI BI8.2.2 Shin ‘Mild Steel, Nickel Plata Gland Packing | Rubberised Asbestos Gasket Compressed Asbestos A familiarity with our Catalogue number is not necessary when specifying our Valves. Provide the following details of the valves to.our Distributor/Stockist:~ Size, Type (Standard, Inverted). Line Fluid, Materials of construct (Body, Plug), Pressure Rating, End Connect ‘Type of Operation.TECHNICAL DATA Catalogue No, End Connection WISI /LOSIVLGINLGSH Flanged BST -D" LWLYEWS1VLOLWLOSINLGLYLGSI3 Flanged Class 125 200, ‘Test Pressure for body and seat including duration of test conforms to BS 6755 Part e Th he DIMENSIONS (mm) Sire Face to Face “Tapped Hote details per flange Flange diameter Flange thickness CA. to top of pus Ci. to bottom of body HAW diameter Max. width Clearance CAL to Quadrant? HUW face CAL 10 wp of HW ‘Wrench No. Sealant sick size ‘These vatves have Nanges tegral wi the body and Glass 125 Gameter + Ligh duly gear unt is recommended for Valves sizes 8° 107 ‘As wo eantinueusty endeavour to improve our products, the data gvan herain are subject to change. antacid vetted by AUDCO INDIA LIMITED LARSEN & TOUBRO LIMITED 8, HOA Inga, Mara Napa 608.209 ita vas Seton Pronavouttesaaed. Fae Oras PO. Ba 9, Caeota 7000 - Ph 22200 " 8 152 184 216 280 3 Flange diameter chs 152 191 229 280 33 : ast © 9 9 Be 254 285 ing tes cus iv 19 28 254 283 CAL to bolom ofthe valve > 15 124 135 18a Clk to wp ol the valve E 13 155 m1 198 253 Double D Wrench No. BO as | Bas Bas BSM Square Head Wrench No a él 7H 10H 10H TEST PRESSURE Max CWP “Test Pressure (pai Catalogue No. | End Connection = a e PRLW IT Flanged BST 100 7 300 220 PRLWI3 Flanged Class 125 200 4 300 220 PRLRV 1S Flange Class 125 200 1 300 220 Test pressure for body and seat including duration of test confarms 10 BS67S5 Part 1 ‘Ase contrucsiy endeavour to improv Our DICOLE. he dala ven hein are subject 9 cage Manus by AUDCO INDIA LIMITED st 849978, Chennai 600 O89. tna Prone 2422028 Fax 401 (4) 202 5088 PONS, :C1078-20.06 (Sapemeden 1071) Mashotod by LARSEN & TOUBRO LIMITED (Wns voles Sarton) On 618, Ceuta POOOPY Pm: BAzz90) - Fax 9.240757 ost Bea 5247, Charnol #00 062 - Ph BSQ24E1 ~Fax 44-8520789 Oy Box 62%, New Dots 110015 - Pr: SO¥SS2- Fan: 11-6808 PO. ox 118, Pune 61 O91 -Ph s62eaa7 Fax: Z12-825010 PO. ex 8119, urbe 60005! «Ph 6401252 «Fax 726801312Steam Jacketed Cast Iron & Carbon Steel, Regular & Venturi Pattern - Standard Type AUDCO Lubricated Taper Plug Valve has been successfully used in a variety of services because of its unique inline maintenance capability. The Plug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluid; this confines corrosion and erosion to less critical areas. Sealing is further enhanced by a specially developed plug sealant charged evenly around the seating surfaces. Plugs from 1'/." are impregnated with a PTFE based anti-friction agent - ‘SUPER LoMu’ which provides greater wear resistance and ensures low consistent operating torque. SUPER LoMu also enhances resistance to seizure. Steam jacketed valves have an integral chamber around the body. The chamber is provided with inlet and outlet screwed connections for passing steam. This feature helps to keep the line fluid heated and prevents solidification inside the valve. Steam Jacketed Lubricated Taper Plug Valves are Materials of construction, Pressure Rating, End all supplied with square stems suitable for wrench Connection and Type of Operation. operation (MJ/MWJ/KWJ Series). Wrenches, as required, should however be ordered separately. 6" valves can be offered with Heavy Duty Worm Gear Unit(KGI Series). Wrenches and Gear Units ‘Specification should be selected as determined by the service | Name of Part (=> Taam Raa conditions, which influence the operating torque Gear Units as ordered are installed on the valves. | Bay Cast ton Carbon See, ASTM and supplied. wsaioce. [x Tosuptol* Cast Iron Valves (MJ Series) and Carbon Steel Fon ae re Ge Valves (MW Series) of sizes upto 4" are of tee Regular Pattern, Carbon Steel Valve (KWI/KGJ - Series) of sie 6" is oF i Cover, Gnd &| Cast tron [ASTMAZI6Ge WC ) ‘Venturi Pattern, fee oe aoe P Asa standard, Steam Jacketed Valvesare supplied 0 “ with AUDCO 731 Plug sealant which is suitable for most services other than acid solutions and | Bolte Carton Steet] Alloy Stee. petroleum products, On request, plug sealant from | SiS. | BST MIT/ASTALA Wh Ge a wide range can be supplied to suitthe | oS Rar | ANS Ries = nature of service. It is recommended that you : = consult us before selecting the plug sealant fora | Shim Mi Steel, Nickel Plated new service. Gland packing | Rubberised Asbestos Compressed Asbestos Valves can be offered with flanged ends to the following standards, 1, Cast fron Valves: BS10 Table D and F ANSV’ ASME B16.1 Class 125. Drilling to DIN 2523 PN 10, BS 4504 PN 10, BS 10 Table E or undrilled flangescanalsobe offered, Carbon Steel Valves: ANSVASME B16.5 ‘Class 300 RF, spirally serrated. Drilling to DIN 2545 PN 40 or BS 4504 PN4O -ean be offered. A familiarity with our Catalogue number is: not necessary when specifying our Valves. Provide the following details of the valves to our Distributor/Stockist:— Size, Type, Line Fluid,TECHNICAL DATA Maximam Working pressure recommended in Jacket-12S psig. ‘Test pressure for body and seat inelading duration of test conforms to BS 6755 Part Catalogue No. MIE Flanged BST" MIE Flanged BST "F Mana Flanged Class 125 MWISVKWISVKGI33 Flanged Class 300 RF DIMENSIONS (mm) a a " ‘Size ‘DN25 DN8O | DNIOO Facet Face | Mi B| 1307 213 | 3556 Mwurewinar — | 158.8 2s | doxs Flange BST-D" ¢| 07 142 | 215.9 diameter BST 1207 2032 | 2286 CL. 125 oso | 127.0 roos | 2256 ct. 300 rato | 158 2096 | 254.0 Fine MD bp] a7 [asa Py thickness MWHKWIKGI 173 206 MB Clio MI el rt | ass 248 ofplug—_MWsKWs i7_| 19 246 tLtobotiom MI Fl as | 9 178 oftody | MW) si] 6s 140 KWIKG) | eee ae ete [ae WW diameter sof - | - | =] - | - Ma. width MO al tos [a0 | ie 229 Mw) me | 108 | 1s 219 ws oe [See ‘Clearance MU g| as | a | 20 | ais | 3s MWWKWS 170 | 210 | 265 | 2s | 36 | 403 kar ef Pe PS | tas ‘CL HW face KGI [ae | ee eee |e Chow KGE ef - | - | - | - | - | ne ‘Size of ache ae] or [ame [iam [am [we ‘onnections asp Tr | psPte| BSP Te| BSPry | BSP Te | NPT No.of Jacket connections Soule [pes eae [iors [oa Pastas of me fe fie fe fee ot) me Jacket connections 4R aL ofa eee poss aes |e Wrench No, a | an | sw [om | su | 08 Seale Stok Size ato fef[efof[e Postions of Jacket oonectone {76° rasod face height is incixded io face ta fae cimenaion and Nange tikness af Garton Ste! Vales. As we continuously endeavour Io inprave cur products, the data Gren Neve are subject a change. Manutaetured by Markoted by il AUDCO INDIA LIMITED LARSEN & TOUBRO LIMITED Ba, MMDA Industrial Area, Maraimalai Nagar = £09 200 (industrial Vaives Section) Ponw (08118) 52828 Fax; o@1-4114-82027. FO. Bou 619, Calouta 700071 «Ph: 2827301 - Fax: -262t025 Adina Oto: ‘Post Bag 976, Charm -600 090 Phong: 292 2323 Fan: «0% (44) 292 S055.0605 PON: ©1002-48-09 Supeeden C8087 Post ag 5247, Chennai €00 092 Ph: BSZ2¥61 = Fax: 44:8520760 P.O, Box 6229, Neve De 110 O15 -Pn=S091902 - Fax: 1-5439626 P.O. Bou 119, Pune 411 001 ~Ph: 628447 - Fax: 212-604910 ~ PO. Box 8119, Mumbai 400051 - Ph: 6401282 - Fax; 224401912Carbon Steel Class 300 - Regular Pattern - Standard Type AUDCO Lubricated Taper Plug Valve has been successfully used in a variety of services because of its unique in-line maintenance capability. The Plug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluid; this confines corrosion and erosion to less critical areas. Sealing is further enhanced by a specially developed plug sealant, charged evenly around the seating surfaces. Plugs from 1'/:" are impregnated with a PTFE based anti-friction agent - ‘SUPER LoMu’ which provides greater wear resistance and ensures low consistent operating torque. SUPER LoMu also enhanees resistance to seizure, Regular Pattern Carbon Steel Lubricated Taper [NameotPart ‘Specification Plug Valves are all supplied with square stems suitable for wrench operation (MW' series). Wrenches, as required, should however be ordered separately. Body & Cusbon Stee! ASTM A105 for sizes upto 1” ASTM A2I6 Gr. WCB for Sizes Lf? & above Asa standard, Carbon Stec! Plug Valves are | Cover 18 2062 supplied with AUDCO 733 Plug sealant which is suitable for most hydrocarbon services. On request, plug sealant from a wide range offered, ‘ASTM Al0S or ASTM A216Gr. WCB ‘Carton Steel - ASTM A216 can be . Plog can be supplied t6 suit the nature of service. It is, Gwen aoe. recommended that you consultus before selecting | ° wnt for anew service. Botting “Alloy Steel ASTM A193 the plug sealant for a new serv Aba sed Ao AIG Shim Mild Stoel Nickel Plated Valves can be offered with screwed ends, flanged | Gland Packing ends and socket weld ends to the following standards, Screwed: BS Tr as per BS21 & NPT as per ANSI/ASME BI.20.1 Flanged : To match flanges drilled to ANSU ASME BI16.5 Class 300 RF spirally serrated. Drilling to DIN 2545 PN40 or BS 4504 PN 40 can be offered, Socketweld: ANSIASME B 16.11 Rubberised Asbestos Gasket ‘Compressed Asbestos A familiarity with our Catalogue numbering is not necessary when specifying our valves. Provide the following details of the valve to our Distributoo/Stockist: = Type (Standard, Inverted) Line Fluid Pattern (Regular, Venturi, Short) Materials of construction (Body, Plug) Pressure Rating End Connection & Type of OperationTECHNICAL DATA ‘Catalogue No, wad Mw34 MWw33 aw39 End Connection ‘Serewed BSP. Tr ‘Screwed NPT Flanged Class 300 RF Socketweld ‘Test pressure for boy and seat including duration of test conforms to BS 6755 Part | . 1 oan DIMENSIONS (mm) Size id voend-Serewed/SW valves Face to Face Flanged valves Flange diameter Flange thickness CAL wvop of plug alsfal = Cit wbettomof body 7 37 3 Max, wid ® 8 ® 15 182 219 [Clearance 1s isa 150 268 325 3 Iotemal deameter of Socketweld end Zz lelel> 2172. zn0s 3378 Depa af soeket (aot chown) 10 B iB Wrench No. ED 2H 3 Sit 7 a ‘Seat sick size « a A “Trim raised faca height fe induded In lace 10 face dimensions and fange thiemness: + Welded on anges As wo continuously endeavour ia improve aur product, the data given herein are subject to change. Manvtactored by Phone: 252 2323, Fax: 91 (éd) 232 50SS.9605 AUDCO INDIA LIMITED Post Bag 978, henna 600.089. PB No: Ob 8 sapere C1035 Marketed by LARSEN & TOUBRO LIMITED (Qnaustial Valves Soeton) P.O. Box 619, Caloutia 700 O71 -Ph: 2822801 - Fax : 0-2821025 ost Bag 5287. Chermal 6002 « Ph 8822141 «Fax: 448520769 P.O. Box 6223, New Doi 110.015 «Ph: 6991902 «Fax: T1o5a3end BO. Box 119, Puna 411 O03 - Ph 24aa7 » Fax :212-624990 P.O, Bex 8139, Mums 400.051 - Ph: 601292 - Fax: 22-640912Carbon Steel Class 150 - Short Pattern - Standard Type AUDCO Lubricated Taper Plug Valve has been successfully used in a variety of services because of its uniqui line maintenance capability, The Piug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluid; this confines corrosion and erosion to less critical areas, Sealing is further enhanced by a specially developed plug sealant, charged evenly around the seating surfaces. Plugs are impregnated with a PTFE based anti-friction agent - ‘SUPER LoMu’ which provides greater wear resistance and ensures low consistent operating torque. SUPER LoMu also enhances resistance to seizure, ‘Short Pattern Carbon Stee! Lubricated Taper Plug Valves upto 8° are alll supplied with square stems suitable for wrench operat Series). Wrenches, as required, should however be ordered separately. Valves 6" to 10" can be ‘offered with Light Duty Gear Units (LO Series). Valves 6" and above can also be offered with Heavy Duty Worm Gear Unit (LG Series), Wrenches and Gear Units should be selected as determined by the service conditions, which influence the operating torque. Gear Units as ‘ordered are installed on the valves and supplied. Valves can also be offered with Carbon Steel Plug. (LS/LOSILGS Series) Asa standard, Carbon Steel Plug Valves are supplied with AUDCO 733 Plug sealant which is, suitable for most hydrocarbon services, On request, plug sealant from a wide range offered, can be supplied to suit the nature of service. It is recommended that you consult us before selecting, the plug sealant for a new service Valves can be offered with flanged ends to the following standards Flanged: To match flanges drilled to ANSI ASME B16.5 Class 150 RF, spirally serrate Drilling to DIN 2543 PN 16 or BS 4504 PN 16 can be offered, Sizes 6° and abave have some holes (refer table) tapped on cach flange to facilitate fastening of the mating flanges and require studs of same diameter of the bolts which they replace. ‘The tapping is to UNC threads for ANSI Class 150 flanges and ISO metric coarse for PN 16 flanges. Specification LWILOL.G-23) LS/.OS/LGS.23 (Carbon Steel ASTM A216 G:WCB ‘Carbon Steel ASTM AZI6Gr. WEBNS: 2062 Carbon seed ASTM A2I6 Gr WCB Boking Alay Sisal Studs ASTM A193 Hex. Screw! Go BTS Hex. Nut ASTM A194 Gr2 ‘Shim ickel Plated Gland Packing | Rubberised Asbestox ‘Compressed Ashestos A familiarity with our Catalogue number is not necessary when specifying our Valves, Provide the following details of the valve to our Distributor/Stockist = Size — Type (Standard, Inverted) = Line Fluid — Pattern (Regular, Venturi, Short) — Materials of construction (Body, Plug) — Pressure Rating — End Connection & Type of OperationTECHNICAL DATA Catalogue No, LW2¥1.S2VLO2¥1OS2MLG2NLGS23 End Connection Flanged Class 1S0RF | _ 285 zo | a0 ‘Test pressure for body and seat including duration of txt conforms to BS 6753 Part | Abo poor soars OES DIMENSIONS (mm) Sue DN 100 | DNase | DN200 | DN2s50 | DN 300 Fave 1a Face B ‘Topped Hole details per Mange lange diameter - Class 150 Flange thickness CAL top of plug ‘=|=] s/o CA. 10 bowtorn of body HAW diameter Max, width Clearance LwiLo. « lela CAL wo Quadram face LO. K CA. to HOW face LG. CAL to top of HAW Lo LG Wrench No, Sealant stick size E “+ Lightaay gear unt ie recommanda tor Valves iro 6° & @° 1.6m razed faco height ie eluded in Face tolace mansions and Range hicknace As me continuous endeavour tolimprove cur products, the daia given herein ae subject to change. Manulactured by nil AUDCO INDIA LIMITED Post 8ag 976, Chennal 600 089 Phone: 282 2928 Fax +91 (44) B42 SOSS9605 Pio: 1006-406 9 .ceoeea cte083) Mackoted by LARSEN & TOUBRO LIMITED (tesutral vaives Section) P.O. Box 618, Calcutta 700 O71 - Ph : 2822904 -Fax: 83-2621025 ost Bag 5247. Cronnal 600 002» Ph: 882241 «Fax 44520769 PO. Box 6223, New Defi 110 015. P= 8531002 « Far: T1-siaeane ‘PO. Box H19, Puna 411 001 - Ph: 6aaa7 «Fax:IN 123 Cast Iron Regular Pattern - Inverted Type AUDCO IN 123 is aself lubricated taper plug valve designed to offer leak tight operation over its entire service life, Ideally suited for non-corrosive services like compressed air, low pressure gas, fuel oil, hot and cold water and low temperature steam. This valve incorporates a simplified system, fed from a sealant reservoir by means of 4 spring loaded piston. The spring serves t0 maintain the plug correctly in its seat. the supply of sealant is continuous and automatic. A delta ring at the shank end provides tight atmospheric sealing. A slight tightening of the delta ring by the setserew will also help in stopping the seat leak. All valves are supplied with levers fitted for quarter-turn operation. These levers are adjusted for open/close positions and should not be disturbed, (As a standard all valves are filled with AUDCO 734 sealant, specially formulated for non- corrosive services like low pressure gas, compressed air, water and steam. Valves can be offered with screwed ends to the following standards: Screwed: BSP pl. as per BS: 21/BS 2779/ 180 228 BSPT as per BS: 21 Over tightening beyond the length of end threads (Refer dimension “F" in the drawing over leaf) whilst installing would not aid better sealing. It is sealing medium like Teflon tape for a leak tight joint, Excessive torque should be avoided as this could cause the ends to crack, ‘Air under water psig bar Body 125 9 Seat (closure) 125 9 Maximum Cold Working Pressure is 125 psigMATERIAL SPECIFICATION ‘Name of Part Specification 1. Body 9 2. Plug Cast Iron to 15-210 GeFG 220 3. Cop 3 Sieel o 18:513 Gr, Ni Plated/ 5 ‘Piston Cast Iron ta 18:210 Ge FG 220 Sieel wo 18:4454 Part 1 Ge2r 2. Sains ISS Par? GSW 6. Gasket ‘Compressed Ashestos - 7. Delta Ring PIFE* & Gland 9. Spacer 3 10. Tab Washer Steel to IS: 2082Gr.A, Zn Plated ; 5 I. Lever 3 Steel to ASTM A307 GLA/ tee Hex: Sasost BS: 1768 Gr ‘Wherever more than one material of constructions specified for component, the choice of any one isa our option. “Rubber as an alternative material canbe offered DIMENSIONS (inch/mm) ValveSize F 05; 8 as 8 O68 16 O69 16 ans 0 O78 20 ‘As we continuously endasvour ta improve our products, the data given havin are subject to change, Marwlactaed by Marketed by AUDCO INDIA LIMITED LARSEN & TOUBRO LIMITED 8, MMMOA incustiat Area, Mavaimatss Nagar 608 200 {industial Valves Section) Phono = 0811482523 Fax: sOT4 114-5237 P.O. Box 618, Caicutta 700001 «Ph: 2822901 . Fax: 39-2821005 Post Bag 5247, Chennai 600 002 Ph : 6522141 - Fax: 44.8520760 PLO, Box 6225; New Dei 10 015.-Pn : Soasae2 - Fax #1549064 P.O. Bok 119, Pune 499 001 - Ph: Gade? Fax 212494090 Phone.=292 2203 Fax: +01 (44) 2960569605 P.O, Box 8119, Mumbai 400 051 -Ph : 6401232 - Fax; 22-6401312 PB No: C1001:3690(tperndneO101.8)AUDCO-FTS Sleeved Plug Valves ‘The AUDCO-FTS Sleeved Plug Valve is a further development of the conventional PTFE sleeved valve. A high standard of performance is achieved by imate contact between plug and the firmly fixed PTFE sleeve in the body. A unique atmospheric sealing arrangement prevents any form of leakage to the atmosphere even under the most adverse conditions, These valves are availablein either Carbon. Steel or Stainless Steel. PTFE SLEEVE ‘The PTFE sleeve serves as the seat for the valve plug permits the use of any bodlyéplug: Positive shut-off is ensured and the valves are free from regular mi ATMOSPHERIC SEALING The primary seal to the aamosphere isthe PTFE Sleeve, Sealing of the cover flange is achieved by means of a PTFE diaphragm which is protected by a metal —aerstane RG ADUETING COUAR PADENG (OMPHITES Fant Ganka TE RSuA ANG wleeene Pea Se ene vena” ~ vom ans diaphragm, Between the caver and metal diaphragm is 4 Graphite delta ring to ensure tight sealing, Leakage past the ste is prevented by this Graphite delta ring which is held by means of a thrust collar, Leakage past the stem is further prevented by means of a Graphite packing that is compressed between two thrust rings on both sides. The adjustable collar makes it possible to compress the Graphite packing uniformly and ensures leak Lightness to atmosphere even under adverse conditions, CONTAINMENT LIPS AROUND BODY PORTS PTPE has a natural tendency to flow under temperatur and pressure, In the AUBCO-FTS, PTFE flow is prevented by means of com ips cast around the body ports, These lips also prevent rotation of the sleeve uring valve operation EXPANSION ZONES IN BODY ‘Two recesses are cast in the body at 90° 10 the ports 10 accommodate expansion of the sleeve. This is so because PTFE has a higher coefficient of expansion than metals, FIRE SAFE AND ANTI STATIC The graphite delta ring and graphite packing in the stem sealing arrangement makes FTS Sleeved Plug Valve inherently fire safe to atmosphere. ‘A build-up of static electricity around the plug ean be caused by the plug mubbing against the PTFE sleeve. A spring is inserted into a groove in the adjusting screw which providesn electrical continuity between the plug and the body, thereby discharging any static electricity build-up. END CONNECTION ‘Valves ean be offered with flanged, serewed and socket weld end connections to the following Standards. nged > ASMEYANSI B16.5 Cl. 150 or 300 = NPT as per ASME/ANSI_ BI.20.1. BSPT as per BS21 Socket Weld : ASMEVANSI B16,11 ScrewedMATERIAL SPECIFICATION Stainless Steet | Carbon Steel Body. ASIMA3S1 | ASTMA2I6 Ge CPM, Gr. WEB. Plug AISE3IQ/ASTM | ASTM ASI A3S1Gr CF8M | Gr CE8Gr. CFM Cover ASTMA381 | ASTMA2I6 Gr. CFSM. Gt. WCB. Virgin PTFE, Graphite Stainless Stee ‘Valvecin Sixe 150 mmand abe are supplied with Gear Unit DIMENSIONS (mm) Openiting lever Duetile Iron or Steet ‘Wherever more than one material of construction is specified the shoiccof using any one is at our option. ‘Valvevare albo availabe in 3161. Alloy 20 and CD MCU on roquest. oe Pape pe | o beeln tape pee tote be Bina ae 3 pertete totes wie Se @ fas fw Poo] pw fae paw be Pope Poe ates 80, 203 | 162 480, a 2 283 100, 29 | 18h 555 _ cd 308 wi == ee mm [= {-|— le be [ a 230 Ro} — 25 49 ue ww [x (—|— Tr Tan 360 sso} — =— $20 289, — Hexagonal thin ruts only should be sed for end flange bolt Sandee or thin us cm he used NIT BSP ‘of 15 and 201m Class 150 valves, For 25mm salves (lass # hexagonalSECTIONAL VIEW ueeve E CATALOGUE NUMBER STANDARDS: Valve design — ASME/ANSI B16,34 Face to Face — BS 2080 and ASME/ ANSI B16.10 ‘Testing — APIS98 TEST PRESSURE Shell (Hyde) | 450 ar | ups | 78 Seat (Air 80 A Fanilisity with our catalogue numbers not necessary when specifying or ordering our valves. If ull description of the valve ‘could be provided we will translate this into catalogue number formulated as per the following system. 80 [we 1 FL G sy Sia ‘Body Material Prowure Class End Connection Operation Options ae Fe - Carton tet 1 Chass 190 Flanged | [Ras wrench ‘SF «Stem Jacke ASTM ARIS 5 Chas 300 SC. Screwed NPT| |G - GearOperace LA Locking Gewes SW. Sovket welt | | Pocumatic Actuator Arengement 8M Seine Sect ASTMASSE = Scr ‘swe coninvousy endeaves to irestie pets, he daa Svan erin are subject 6 change. ‘Manufactured by Maiatediy AUDCO INDIA LIMITED LARSEN & TOUBRO LIMITED Post Bag 976, Chennai 600080 (tsi! Yves Sactor) Phono 252 2823 Fax + 1 24) 252 5055 PO No: C1ON 22000 pipes G81 AO. Gox 619, Caouta TOD OF =P: 2627901 Fax: on.2801025 Posi ag 247, Channa 600 002 Ph. 8529341 «Fax: 46-0520769 0. Box 6223, Now Out T1DOTS Pre S0S1302 Fax: 15630526 0. Bex 119, Pune 417 001 P= 26087 Fay 212-674010 0. Box 810, Mumba 09 061» Pr @x01232- Fax 22-6801912AUDCOLOY Regular & Short Pattern - Standard Type AUDCO Lubricated Tay xr Plug Valves have been successfully used ina variety of services because of its unique in line maintenance capability. The Plug and Body seating surfaces, which are lapped and matched, are not exposed to the line fluid; this confines corrosion and erosion to less critical areas. Sealing is further enhanced by a specially developed plug sealant charged evenly around the seating surfaces. Plugs from 1'/:" areimpregnated with a PTFE based anti-friction agent - ‘Super LoMu’ which provides greater wear resistance and ensures low consistent operating torque, SUPER LoMu also enhances resistance to seizure. Audeoloy Lubricated Taper Plug Valves upto 8" are all supplied with square stems suitable for wrench operation (MD Series). Wrenches, as required, should be ordered separately. Valves, 4" to 8" can be offered with Light Duty Gear Units (MDO Series), Valves 6° and above can be offered with Heavy Duty Worm Gear Unit (MDGILDG Series). Wrenches and Gear U: should be selected as determined by the service conditions, which influence the operating torque, Gear Units as ordered are installed on the valves and supplied. Valves upto 8" are of Regular Pattern (MD series) and 10" & 12° are of Short Pattern (LDG series) As a standard, Audeoloy Plug Valves are supplied with AUDCO 147 Plug sealant which is suitable for services like nitrating acids, sulphuric acid and oxidizing chemicals. On request, plug sealant from a wide range offered, can be supplied to suit the nature of service, It is, recommended that you consult us before selecting the plug sealant for a new service. Valves can be offered with serewed ends and flanged ends to the following standards, Flanged : fo match flanges drilled to BS 10 Table D, F and ANSI/ASME BIG. | Class 125. Drilling t DIN 2532 PN 10, BS 4504 RN 10 of BS 10 Table E can be offered Valves can also be offered with undrilled flanges. ‘Name of Part ‘Specification Body & ‘Audcoloy Cover de Cast ion Glan IS 210Gr, FG 220 Plug ‘Audcoloy Carton Stee! BS.970 220 Mar ANSI BIS2.1 ANSI BIS.22 Stainless Steel, AISI 304 (Gland Pucking Rubberised Asbestos ‘Gasket Compressed Asbestos Audeoloy” is an aust BS3468 Grade AUS 104, alloy cast iron as per A familiarity with our Catalogue number is not necessary when specifying our valves. Provide the following details of the valves to our Distributor/Stockist— Size, Type (Standard, Inverted), Line Fluid, Materials of construction (Body, Plug), Pressure Rating, End Connection, Type of Operation,TECHNICAL DATA Catalogue No. End Connection MDH/MDOW/MDGILDGH. ‘Flanged BST'D* MDUEMMIDOLEMDGILE Flanged BST -F MDISMDOIVMDGIMLDGI3 ‘Fanged Class 125 “Test pressure for body and seat including duration of test conforms to BS 6735 Part L DIMENSIONS (mm) © wo] aa N25 |>N200 |DN250] DN300 Face to Fase i as72 [3302 | ass6 ‘No. oftapped BS a] Iles perfange CL. 128 2 | 2 Flange Diameter STDC] 1207 Saas [woes | FRE BST -F 1207 sons || cL125 too sin | s064 | ax26 Flange thickness: BST-D"D | 127 302 | 318 BST-F ie =a cL 125 127 soz | sis ‘Cito wp of plug EB] 12 Sale ‘CL tobouom of kody F 29 | 2 HAW Diamsier 6 s7s_[ 578 Max. wid u ‘Light oy pear unl ie recommended tx Valves size © As we continuousty endeavour io knprove our products, the data gven herein are subject to change. Manutactured by Markoted by AUDCO INDIA LIMITED LARSEN & TOUBRO LIMITED ea (Indust Vatves Section) Channa 0 Ue, PO, Box 619, Calouta 700 O71 «Ph: 2822301 - Fax: 99-2821025 Phone; 538 2323 Fax: +01 44) 202 SOSs005 Post Bag £247, Chennai 600.002 - Ph = 8822141 - Fax : 44-8520760 sraialainagar Week PO. Box 6223, New Da 110015 - Ph 5091902 - Fax: 11-5499528 BE, MMDAlndustial Area, Maralmalal Nagar - 609 200 PO, Box 119, Pune 491 001 - Ph: A447 «Fax: 212-628910 Phone: (414) 52aza Fax 91 04114 S227 PO, Box 8118, Mumbai 400081 -Ph 401282 Fax : 224401912 PAN C1004-16.09 apceen C1004