WI-XML Page 1 of 10

Transporter Fitting Locations No. 804 / 1

Edition 02.2010

Pin connector assigment of selected connections

Overview:
1 - Ignition/starter switch -D-
 On steering column
 Connector assigment → chapter
2 - Onboard power supply control unit -J519-
 Below the dash panel
 Connector assigment → chapter
3 - Steering column switch -T41-
 On steering column
 Connector assigment → chapter
4 - Diagnosis connection -T16-
 Left under dash panel
 Connector assigment → chapter
5 - Control unit in dash panel insert -J285-
 Pin connector -T32- → chapter
 Pin connector -T32a- → chapter
WI-XML Page 2 of 10

Contact assignment of pin connector on ignition/starter switch -D-

1 - Terminal 50
2 - Terminal 75
3 - Terminal 30
4 - Terminal P
5 - terminal 50b
6 - Terminal 15
7 - Terminal 30
8 - terminal 86s

Onboard power supply control unit -J519-

Connector assigment:
A - Pin connector, T6, black → chapter
B - Pin connector, T6a, brown → chapter
C - Pin connector, T6b, red → chapter
D - Pin connector, T5, black → chapter
E - Pin connector, T5a, brown → chapter
F - Pin connector, T6c, black → chapter
G - Pin connector, T18, black → chapter
H - Pin connector, T6d, brown → chapter
I - Pin connector, T18a, brown → chapter
J - Pin connector, T6e, red → chapter
K - Vacant
WI-XML Page 3 of 10

Contact assignment of pin connector -T6-, on onboard supply control unit (Item A)
Pin Assignment/Component Terminal
1 - 636 - Earth point onboard supply control unit 31
2 - Vacant
3 - B129 - Connection (interior light, 31l), in interior wiring harness TK
4 - B153 - Connection (RTS), in interior wiring harness (output right turn signal) BLR
5 - SB36 - Fuse 36 on fuse holder B (turn signal input) 30a
6 - B152 - Connection (LTS), in interior wiring harness (output left turn signal) BLL

Contact assignment of pin connector -T6a-, on onboard supply control unit (Item A)
Pin Assignment/Component Terminal
1 - Z5 - Front passenger side heated exterior mirror (output)
2 - Z4 - Driver side heated exterior mirror (output)
3 - SB16 - Fuse 16 on fuse holder B (input) 15
4 - SB20 - Fuse 20 on fuse holder C (input heated exterior mirror) 30a
5 - SB17 - Fuse 17 on fuse holder C (interior light output) ¹) 30g
SC24 - Fuse 24 on fuse holder C (interior light output) ¹) 30g
5 - B315 - Positive connection 1 (30a), in main wiring harrness (interior light output) ²) 30g
6 - SB7 - Fuse 7 on fuse holder C (interior light input) ¹) 30a
6 - SB17 - Fuse 17 on fuse holder C (interior light input) ²) 30a

Note
 ¹) for models with roof console only
 ²) for models without roof console only

Contact assignment of pin connector -T6b-, on onboard supply control unit (Item C)
Pin Assignment/Component Terminal
WI-XML Page 4 of 10

1 - Vacant
2 - SC35 - Fuse 35 on fuse holder C RFL
3 - Vacant
4 - Vacant
5 - Vacant
6 - B520-Connection (RL), in main wiring harness RFL

Contact assignment of pin connector -T5-, on onboard supply control unit (Item D)
Pin Assignment/Component Terminal
1 - J49-Electric fuel pump 2 relay 85
2 - V - Windscreen wiper motor, Pin 1 (speed 2) 53b
3 - V - Windscreen wiper motor, Pin 2 (speed 1) 53
4 - 370 - Earth connection 5, in main wiring harness 31
5 - SB32 - Fuse 32 on fuse holder (windscreen wiper motor input) 30a

Contact assignment of pin connector -T5a-, on onboard supply control unit (Item E)
Pin Assignment/Component Terminal
1 - SB3 - Fuse 3 on fuse holder B (input) 30a
2 - H1 - Horn or dual tone horn (output)
C13 - Positive connection in dual tone horn wiring harness (output)
3 - SB13 - Fuse 13 on fuse holder B (horn or dual tone horn input) 30a
4 - Z1-Heated rear window (output)
5 - S41-Heated rear window fuse (input) 30a

Contact assignment of pin connector -T6c-, on onboard supply control unit (Item F)
Pin Assignment/Component Terminal
WI-XML Page 5 of 10

1 - Vacant
2 - Vacant
3 - B441-Connection (CCS), in main wiring harness, GND on/off
4 - E45-Cruise control system switch, T41 Pin 31, GND R
5 - E45-Cruise control system switch, T41 Pin 27, GND memory
6 - E45-Cruise control system switch, T41 Pin 30, GND memory

Contact assignment of pin connector -T18-, on onboard supply control unit (Item G)
Pin Assignment/Component Terminal
1 - B406-Connection 1 (convenience CAN bus, low), in main wiring harness CAN-L
2 - B397-Connection 1 (convenience CAN bus, high), in main wiring harness CAN-H
3 - Vacant
4 - E2-Turn signal switch, T41 Pin 32 (right turn signal input) BLR
5 - SD18 - Fuse 18 on fuse holder D (input battery voltage measurement, positive) 30A
6 - A - Battery (input battery voltage measurement, negative) 31
7 - F2 - Driver door contact switch (input)
8 - Vacant
9 - O4 - Positive connection (30as), in seat heating wiring harness (deactivate - output J131, J132)
10 - E3 - Hazard warning light switch (input)
11 - F11 - Rear right door contact switch (J741 Pin 7), (input)
12 - E2-Turn signal switch, T41 Pin 34 (left turn signal input) BLL
13 - F10 - Rear left door contact switch (J741 Pin 8), (input)
14 - E15 - Heated rear window switch (input)
15 - H-Horn plate, T41 Pin 10 (input)
16 - F266 - Bonnet contact switch (input)
17 - F3 - Front passenger door contact switch (input)
18 - E231 - Exterior mirror heater button (input)
WI-XML Page 6 of 10

Contact assignment of pin connector -T6d-, on onboard supply control unit (Item H)
Pin Assignment/Component Terminal
1 - J245 - Sliding sunroof adjustment control unit (output)
2 - E180 - Heated windscreen switch (input) ¹)
3 - G213 - Rain sensor, (signal - input)
4 - J39 - Headlight washer system relay (output) 85
5 - K122-Heated windscreen warning lamp ¹)
6 - G213 - Rain sensor (GND) 31

Contact assignment of pin connector -T18a-, on onboard supply control unit (Item I)
Pin Assignment/Component Terminal
1 - Vacant
2 - K10 - Heated rear window warning lamp (output)
3 - Vacant
4 - F5 - Luggage compartment light switch (input via B475)
5 - F111 - Rear lid contact switch (input via B534)
6 - SB35 - Fuse 35 on fuse holder B (input via B340) 58d
7 - V - Windscreen wiper motor (input)
8 - D - Ignition/starter switch, Pin 8 (input - S-contact via SB19 and B518) 86s
9 - E34 - Rear wiper switch, T41 Pin 20 (input - windscreen and rear window washer pump)
10 - F4 - Reversing light switch (input - reversing lights via B520) RFL
11 - E38-Intermittent wipe regulator, T41 Pin 17 (input - intermittent) INT
12 - D-Ignition/starter switch, Pin 8 (input) 50b
13 - C - Alternator (input - battery charge) 61
14 - E22-Intermittent wiper switch, T41 Pin 16 (input - windscreen wiper speed 2) 53b
15 - D-Ignition/starter switch, Pin 2 (input - X-contact via B173) X
16 - K6-Hazard warning light system warning lamp
WI-XML Page 7 of 10

17 - Vacant
18 - E22-Intermittent wiper switch, T41 Pin 16 (input - windscreen wiper speed 1) 53

Contact assignment of pin connector -T6e-, on onboard supply control unit (Item J)
Pin Assignment/Component Terminal
1 - A18 - Windscreen heater voltage transformer (output) ¹)
2 - J7 - Battery isolation relay (output) 85
- J713 - Second battery charging circuit relay (output) 85
3 - J207 - Starter inhibitor relay (output) 50a
4 - J98 - Gearshift indicator control unit (output)
5 - G213 - Rain sensor (voltage supply - output) 15
6 - F125 - Multifunction switch (input - release AG)

Note
¹) is still not delivered

Contact assignment of pin connector -T41-, on steering column switch

1 - T41/1 - Steering angle sender (vacant)
2 - T41/2 - Steering angle sender (CAN-low)
3 - T41/3 - Steering angle sender (CAN-high)
4 - T41/4 - Steering angle sender (terminal 31)
5 - T41/5 - Steering angle sender (terminal 30)
6 - T41/6 - Steering angle sender (terminal 15)
7 - T41/7 - Airbag +
8 - T41/8 - Airbag -
9 - T41/9 - Horn 31/ multifunction steering wheel -
10 - T41/10 - Horn 71a/ multifunction steering wheel - data wire
11 - T41/11 - multifunction steering wheel +
12 - T41/12 - vacant
13 - T41/13 - vacant
14 - T41/14 - vacant
15 - T41/15 - terminal 53b, wiper 2nd speed
16 - T41/16 - terminal 53b, wiper 1nd speed
17 - T41/17 - wiper potentiometer
18 - T41/18 - Multifunction indicator reset
WI-XML Page 8 of 10
19 - T41/19 - Terminal 31
20 - T41/20 - Terminal 53c
21 - T41/21 - Rear wiper
22 - T41/22 - Terminal 15
23 - T41/23 - Multifunction indicator -
24 - T41/24 - Multifunction indicator +
25 - T41/25 - vacant
26 - T41/26 - CCS - on/off
27 - T41/27 - CCS memory
28 - T41/28 - CCS terminal 15a
29 - T41/29 - CCS - on/off
30 - T41/30 - CCS SET
31 - T41/31 - CCS resume
32 - T41/32 - Right turn signal
33 - T41/33 - Turn signal terminal 31
34 - T41/34 - Left turn signal
35 - T41/35 - Right parking light
36 - T41/36 - Parking light (input)
37 - T41/37 - Left parking light
38 - T41/38 - Flasher terminal 30
39 - T41/39 - Main beam terminal 56a
40 - T41/40 - Dipped beam terminal 56b
41 - T41/41 - Dipped beam/ main beam terminal 56

Contact assignment of pin connector -T16-, on diagnosis pin connector

1 - T16/1 - Terminal 15
4 - T16/4 - Terminal 31
5 - T16/5 - Terminal 31
6 - T16/6 - CAN-H (motor, switched)
7 - T16/7 K-diagnosis wiring
14 - T16/14 - CAN-I (motor, switched)
16 - T16/16 - Terminal 30

Control unit in dash panel insert -J285-

Note
The connector assignment on the dash panel insert despends on the equipment, the country and the
engine version of the vehicle.

T32 - 32 pin connector, blue

WI-XML Page 9 of 10
1 - T32/1 - Terminal 15, positive
2 - T32/2 - vacant
3 - T32/3 - Speed signal-output
4 - T32/4 - vacant
5 - T32/5 - Fuel gauge sender
6 - T32/6 - Warning lamp for daytime running lights
7 - T32/7 - Terminal 31, sender earth
8 - T32/8 - vacant
9 - T32/9 - Terminal 31, earth
10 - T32/10 - Oil pressure switch
11 - T32/11 - vacant
12 - T32/12 - vacant
13 - T32/13 - vacant
14 - T32/14 - Rear fog light warning lamp
15 - T32/15 - vacant
16 - T32/16 - vacant
17 - T32/17 - Main beam warning lamp
18 - T32/18 - vacant
19 - T32/19 - vacant
20 - T32/20 - vacant
21 - T32/21 - vacant
22 - T32/22 - Coolant shortage warning lamp
23 - T32/23 - Terminal 30, positive
24 - T32/24 - Terminal 31, earth
25 - T32/25 - Self-diagnosis/ K-wire
26 - T32/26 - Right parking light - input signal
27 - T32/27 - Left parking light - input signal
28 - T32/28 - Speed signal-input
29 - T32/29 - Brake system warning lamp
30 - T32/30 - S-contact
31 - T32/31 - Belt switch warning lamp
32 - T32/32 - vacant

T32a - 32-pin connector, green

1 - T32a/1 - Radio clock receiver, + 5 V
2 - T32a/2 - Immobilizer reader coil
3 - T32a/3 - Radio clock receiver, sender cable
4 - T32a/4 - CAN
5 - T3a2/5 - vacant
6 - T32a/6 - Washer fluid level warning lamp
7 - T32a/7 - Brake pad warning lamp
8 - T32a/8 - CAN-H (convenience)
9 - T32a/9 - CAN-L (convenience)
10 - T32a/10 - Radio clock receiver, earth
11 - T32a/11 - vacant
WI-XML Page 10 of 10
12 - T32a/12 - vacant
13 - T32a/13 - Handbrake warning-input
14 - T32a/14 - vacant
15 - T32a/15 - CAN-H (info)
16 - T32a/16 - CAN-L (info)
17 - T32a/17 - Immobilizer reader coil
18 - T32a/18 - Oil level and oil temperature sender
19 - T32a/19 - CAN-H (drive train)
20 - T32a/20 - CAN-L (drive train)
21 - T32a/21 - vacant
22 - T32a/22 - vacant
23 - T32a/23 - Multifunction indicator - up
24 - T32a/24 - Multifunction indicator - down
25 - T32a/25 - Multifunction indicator 1/2 - reset
26 - T32a/26 - Ambient temperature sensor
27 - T32a/27 - CAN-H (out)
28 - T32a/28 - CAN-L (out)
29 - T32a/29 - vacant
30 - T32a/30 - vacant
31 - T32a/31 - vacant
32 - T32a/32 - vacant