Scribd
Upload
47 views

Lesson 1 Introduction Rev B

The document provides information on the upgrades and new features of the Network Platform compared to the Smart Platform. Key points include: 1. The Network Platform features new processing hardware that provides faster scanning speeds and higher data rates compared to the Smart Platform. 2. Many components remain the same between the two platforms, including sensors, the frame, motors, and traversing cables. 3. The Network Platform features upgrades like new software, troubleshooting utilities, and enhanced health pages.

Uploaded by

FachrurroziAs
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
47 views

Lesson 1 Introduction Rev B

The document provides information on the upgrades and new features of the Network Platform compared to the Smart Platform. Key points include: 1. The Network Platform features new processing hardware that provides faster scanning speeds and higher data rates compared to the Smart Platform. 2. Many components remain the same between the two platforms, including sensors, the frame, motors, and traversing cables. 3. The Network Platform features upgrades like new software, troubleshooting utilities, and enhanced health pages.

Uploaded by

FachrurroziAs
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 22

Network Platform Class

1. Introduction to the Network Platform


2. Electrical Functions
3. Health Pages
4. Installation and Maintenance Manual
5. Diagnostic Tool
6. Scanner Debug Tool
7. Service Work Station
8. Configuration Tool
9. NP Update Tool
10. Client Suite
Document Revision:
Rev A
By S. Cleland
Date 18/3/09
Network Platform
What is New?
1. New Processing Hardware
2. Faster Scanning (500 mm/second)
3. Higher Databox rates (250 DB/s)
4. New Software
5. New Troubleshooting Utilities
6. New Maintenance Utilities
7. Enhanced Health Pages
8. New Manuals and Functional Drawings
9. Sensors and Scanner Hardware Remain The Same as the Smart
Platform
10. Retrofit for Smart Platforms with -004 backplane.

Lesson 1 - Introduction to Network 2


Platform
What is the same?

1. Sensors
2. Frame
3. Motor Controller (Uses ACS 101 or VLT)
4. Frame Control Panels
5. Traversing Cables and Carrier
6. Remote J-Box is supported
7. Utilities (Power, Air, Water)

Lesson 1 - Introduction to Network 3


Platform
Sensors
• All sensors except TLK/TLP/Basis Weight, Old Ash, and Smoothness are
supported. ( TLS1 will be supported in Release 1.3 due Mar/Apr ’09)
• Pigtails and carriage board (interconnect boards NP700) are the same.

Lesson 1 - Introduction to Network 4


Platform
Frame
• Unchanged mechanically.
• Installation procedure is the same
• Head Package is unchanged
• Wiring to switches, encoder, digital inputs, and motor
controller is the same.

Lesson 1 - Introduction to Network 5


Platform
Frame Control Panel
• Frame control panel operates the same Except:
– Manual limit led flashes if illegal limit is entered.
– Maintenance and standardize lights flash after restart
before encoder sync.
– Additional function for frame tuning.

Lesson 1 - Introduction to Network 6


Platform
Traversing Cables and Carrier
• The same cables are used for the NP1200 and SP1200 with -
004 backplane.
• The same cables are also used for the NP700 and SP700
with -004 backplane.
• The same cable carrier as Smart Platform is used.
• Carriage Board (interconnect boards) are the same as Smart
Platform.

Lesson 1 - Introduction to Network 7


Platform
New Processing Hardware

ASPC

SBC w flash card

Lesson 1 - Introduction to Network 8


Platform
SSIB
ASPC

ASPC SSIB
(Standard Signal Interconnect Board)

Passive PCI Backplane

PSIB

SSIB
PSIB
9
New Processing Hardware
• Network Platform uses one Single Board Computer with Embedded XP. Operating
system is stored on Flash but locked to SBC.

• Communication to the CPU is by TCP/IP over Ethernet either to port on SBC or


through a Fiber Optical/Electrical Ethernet Board (Board not shown).

SBC Bottom Side SBC Top Side


Lesson 1 - Introduction to Network 10
Platform
• 2 GB Flash Card used, no hard drive
• Very few writes are done to flash card.

Lesson 1 - Introduction to Network 11


Platform
• SBC & CF Partioning

Active Memory

XPe Config Files


&
Application SW

Lesson 1 - Introduction to Network 12


Platform
I/O by DAQ Board
(Two boards may be used in larger systems)

32 analogue channels with up to 250kS/s


Most channels at 2000 measurements per second.
IR sampling at 20000 measurements per second
Lesson 1 - Introduction to Network 13
Platform
RS-485 serial board supports Color Sensor and
Frame Control Panels - 8 channels

Lesson 1 - Introduction to Network 14


Platform
Fiber Optical/Electrical Ethernet Card
Used to support Fiber Optic Connection

Lesson 1 - Introduction to Network 15


Platform
HDLC Card for Fiber Orientation
Sensor

Lesson 1 - Introduction to Network 16


Platform
Signal Processing

SSCB Standard Signal Conditioning Board (Two boards in larger systems)


Conditions signals for the DAQ and the PSCB
Preconditions the signals before they are sent to the DAQ board.
Has LEDs that indicate the validity of, SS (Watch Dog), +5 VDC, +12 VDC, -12VDC,
+15 VDC, and -15 VDC. Lesson 1 - Introduction to Network 17
Platform
Signal Conditioning
Typical PSCB Status Leds
DH 1 BW SHUTTER
DH 2 BW INTERNAL SMP
DH 3
DH 4
AH 1 BW HEATER TOP
AH 2 ASH HEATER TOP
AH 3 CAL SOL TOP
AH 4 BW HEATER BOT
AH 5 ASH HEATER BOT
AH 6 CAL SOL BOT
AH 7 TOP or BOT COL HEATER
AH 8 IR PWR – Hemi +
AH 9 IR PWR – Top Refl
AH 10 IR PWR – Bot Refl
PSCB Power Signal Conditioning Board
Power output to heaters, shutters, solenoids PWM 1 ASH SHUTTER

PWM 2 ASH INTERNAL SMP

Lesson 1 - Introduction to Network 18


Platform
Signal Processing

Standard -001 for 4 core sensors plus 1 -002 required for additional sensors

SSJB Standard Signal Jumper Board


(Two Boards in larger systems)

Lesson 1 - Introduction to Network 19


Platform
Modular Power Supply
± 12 VDC, ± 15 VDC + 24VDC and +42VDC

Note : 24 V & 42 V Optional


The 24 VDC is used with the CSS
The 42 VDC is used for flag driver in
Reflection IR & Coat weight sensors

Frame Modular Power Supply


± 12 VDC, ± 15 VDC + 24VDC and +42VDC
Lesson 1 - Introduction to Network 20
Platform
Other Power Supplies

PC Power Supply Lamp Power Supply for Gloss and Optipak

Lesson 1 - Introduction to Network 21


Platform
Power Supply Drawer

Frame Power Supply

Fuse

Sola Transformer

Lesson 1 - Introduction to Network 22


Platform

You might also like