Scribd
Upload
118 views

Intelligent Reactive Compensation Controller

Intelligent

Uploaded by

Fernando Rubio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
118 views

Intelligent Reactive Compensation Controller

Intelligent

Uploaded by

Fernando Rubio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 6
mriehoent Pe Reactive Compensation | sete srameaeee COntroller JKW series > intelligent General Description Functional characteristics Service condition 23 << ZHIYUR Reactive Compensation Controller i {JI sete intligent low voltage reactive auto compensation controller (abbr Controle) isthe special device for compensating reactive power for low voltage distribution system. ts sampling physical quantty is reactive power, with various specications of 1~16 step dynamic output JKWD15, JKWD2O) and static utputJKWI5, JW2C. JRWIBF, JRWIB), JKW3B. JKW28) ec, as wall as with characteristics of novel design, mutfunction, fine control performance and high allabilty et. tis at the leading postion among similar products in domestic market and supplies a brand new device fo istibuton automation, This series product showing type fae “20 when power ‘on denotes the program version of product 1. Realtime displays network tate: including reactive power, power factor, secondary current, primary curent and system voltage etc 2, Automatically ecognize the polarity of sampling signal, to avoid non-polarty connection. 3. With power down memory function by seting parameter. Data will not lose after power down, ‘4 With ove voltage and under voltage protection functions. 5. With input and resect delay can be adjusted separately, with applicable capacity for electric network. 6. Re-inputting locking time can beset to ensure the capacitor with enough discharge time before inputting. 7. Output group quantity can cutoff one group or start one group a wil through the button. 9. With strong anti-intrference capacity, can directly ess the interfering impulse with total amplitude value of 2000 from periphey. Power voltage: Rated vale is AC 380 fluctuation should not exceed +10%, ‘Ambient temperature: -250~55° Relative humidity: Max 90% (at 20°). ‘Altitude: not exceed 2000, Environmental condition: without explosive and flammable dangerous medium, without corrosive metal gas and ‘the conductive dust that may damage the electric insulation. Basic technical parameters Ex-store setting value for each parameter Operation method for manual function JKW series 4 Intelligent Reactive Compensation Controller Rated current: ACO~5A ‘Current input impedance: 0.029 Frequency: SOH2/60H2 Rated voltage: AC 220V/380V Protection grade of shel 1P30 Power: Max EW ‘Contact capacity: Dynamic state DCI2W/SOMa(Staic state ACZ20V/7A) each branch Sensitivity 50m Code Meanings ‘Setting value ‘Adjustable range Po Input threshold for power factor 0.950 0.800~1.000 p02 Resect threshold for power factor 1.000 0.900~-.900 p03 Input delay 30 1~25030.1~60.05, Pow cut delay 30 1~25030.1~60.05 Pos (ver voltage protection aga 400~500/230-27 P06 Re inputting locking time 30 0-240 por ‘ansformation ratio of transformer 500 5~10000 orc __Outputof each controled capacitor 5 0-200kvar ‘lick the set key Il to perform fast ranser between automatic and manual operation. AUTO/MAN signal ight flash frequently under manual state. Operate A can input one group. Operate ¥ can cut the group of input ‘copactor. Brief instruction for choosing JKW series products Model Rated voltage ‘Tapping size Output JK 380V 113x113, 1-12 step static outout sRw2c 20v 113x113, 1-12 step static output JKWIBF 380V 140% 102 1-12 step static output sew) ov 140% 102, 1-12 step state output sKW38 380V 162% 102 1-12 step static outout sKw28 20v 162% 102, 1-12 step stale output JKWOIS 380V 113x113 1-12 step dynamic output Jewo2c 220v 13x13, 1-12 step dynamic output ZHIYUE >>> 24 JKWF series P intelligent Reactive Compensation Controller General Functional characteristics 28 << ZHIYUR i IWF series reactive power compensation controller (hereinafter refered to as controll, taking postion SCM ‘score, adopting the contol scheme of phase splitting sampling, phase spliting compensation and common ‘compensation plus phase splitting compensation, is used for controling reactive compensation devices in unbalance three-phase load electric system with ACSOH2, 0.4KV. (WS I sngle;phase sampling, with same basic function, to use referring tothe instruction). 1. Realtime displays three-phase network tate: including system voltage, system current, active power, reactive ‘power apparent power, power factor and electric network frequeng, contol parameter et. 2. Automatically recognize the polarity of sampling signal, to avid non-polar connection 3. Mth power down mereny function by setting parameter. Data wll natioe after power down, 4 With over voltage and under voltage protection functions. 5. With double input threshold Input jst canbe performed only the power factor and reactive power are lower than set valu, to avoid input-eset vibration. 6. (th input and resect delay canbe ase separate, wth applicable capaci for elec network, 7..With 5 kinds of input-resect program: sequential input-resect, code input-resect and optimized input- resect modes. 8. Reinputting locking time canbe set to ensure the capacitor with enough discharge time before inputting. 9. Output group quantiy can cut off one group or tart one group at wil through the button. 10. Whole cit ofall kinds of parameter is adjustable, can be widely used in ferent eectic network. 11, With strong ant-itererence capacity can directly resist the interfering impulse with otal amplitude value of 2000V from periphery. 12, Compensation modes: hase spliting compensation can be set, phase spliting compensation plus three- phase compensation, three-phasecompensation 13, Output modes: stati, dynamic and compound ete. Service condition Basic technical parameters Ex-store setting value for each parameter JKWF series < Intelligent Reactive Compensation Controller Power voltage: Rated value is AC220¥, fluctuation should not exceed 10%. Ambient temperature: -250~55. Relative humidity: Max 90% (at 20) ‘Altitude: Not exceed 200m, Environmental condition: Without exlosve and flammable dangerous medium, without corrosive metal gas and the conductive dust that may damage the electric insulation, Rated current: ACO~5A, Frequency: SOH2/60H2 Protection grade of shel P40 Contact capacity: Dynamic state DC12V/50Ma\Statc state AC220V/7A}each branch Sensitivity: 20mA, code Meanings Setting value Adjustable range Po} Input threshold for power factor 0.950 0.800~1.000 poz Resect threshold for power factor 1.000 0.800—.900 p03 Input delay 10s poy Gut off delay 105 Pos (Over wltage threshold 245 220V~300V Pos Capacitor discharge delay ° 0~240s pao ‘Sampling curent transformer ratio 500 5~9000 Pa Compensation scheme _3F07(2F06) (0F16-5F01(0F12~4F09) GOrCA __Output of each controlled capactor 5 0-200!var PFC series P Monitoring intelligent Compensation Controller | \ t | t oll ba oe! | Safety operation prc type distribution monitoring controller should be installed and operated by the electrician with certain and installation experience Pease carefully read the instruction before using. According tothe modes and steps stipulated Service conditions Technical parameters 27 <<< ZHIYUR inthe instruction when debugging and musn't confuse the connection diagram and terminal label at back ofthe controle. 1. Attade: not ceed 2500. 2. Ambient temperature: -25°0~50. 3. Air humidity should not exceed 50% at 40°C and not exceed 90% at 20°C. “4. No corrosive gas, conductive dust and flammable and explosive medium around the ambient. 5. No ferce vibration at instalation site. 1. Basic parameter Power voltage: AC220V-+10% Signal frequency: 45-65H2 Signal current: ACO-SA. 2. Measure precision Voltage: +0.5% Power factor: 1.0% Reactive power: 1.0% Reactive coulom: 1.0% System clock: 49pm. yearly error less than 2min Power frequency: 45-654 ‘Signal voltage: ACS0-260V ower consumption of machine: <10VA ‘Current: 0.5% ‘Active power: £1.0% ‘Active coulom: 1.0% Electric network frequency: +:0.01H2 Main functions Analysis system software for upper position computer PFC series 4 Monitoring Intelligent Compensation Controller 1. PFC distribution monitoring controle is mainty used for auto controling to capacitance reactive compensation >> 28 p> 2KW186 Series High Voltage Reactive Power Compensation Controller Service conditions model Technical parameters 1. Basic parameter 29 << ZHIYUE JIRW18G high votage reactive power compensation controller sa new generation dlstrbution test control device asintegrating data acquistion, power network parameter analysis, reactive power compensation communication, 25. unit, whichis ultable for contzoling the hig voltage power network syste parameter monitors and reactive compensation, can offer the perfect and accurate data bass for power network safety running, reasonable distributing load improving electric energy quality et. 1. Altitude: aot exceed 2500m. 2. Ambient temperature: 250-SOT. 3. Air humidity should not exceed 50% at 40°C and not exceed 90% at 200. 4, No corosve gas, conductive dust ad flammable and explosive medium around the ambient. 5. No fer vibration at installation ste, Product model Tapping size Powervoltage Signal frequency Control creult_ Display JRWIBG 139139 ac220v 50/602 1-6 Leo Power voltage: AC220V+10% Power frequency: 45-654 Signal frequency: 45-65H2 Signal voltage: ACS0-260V Signal current: ACO-5A Power consumption of machine: <10VA Technical parameters 2. Measure precision Function characteristic JKW18G Series High Voltage Reactive Power Compensation Controller < Voltage: 0.5% ‘Current: £0.5% Power factor: 1.0% Active power: +1.0% Reactive power: 1.0% Active coulom: 1.0% Reactive coulom: 1.0% Electric network frequency: 0.01H System clock: +4ppm, yearly eror less than 2min suitable for controling the high voltage power network system, to make the power factor of electric network to be optimal Fullbig screen display (contain back ight. The bac ight is bright by operating any key. If within tin there isn't any operation, the back ight will extinguish automatically, with friendly human machine interface and visual and simple Chinese present operation. Actual te calculation displays three-phase power factor, three-phase active power, three-phase reactive power, three-phase voltage, three-phase current, zero sequence curent, three-phase wotage distortion rate. Three;phasecurent distortion rate, 3-13 times voltage and aurent harmonic wave contain rate, rel time dock, active electrical degree and reactive electical degree ete. JRW18G type distribution monitoring controller can widely store 24 integral points data and the daily statistical data reaching min 200 days. And also can be extended to 800 daye according to user's requirement, Data Includes the three-phase voltage, three-phase current, three-phase power factor, three- phase active power, three-phase reactive power, three-phase voltage distortion rate, three-phase current distortion rate active lectical degree and reactive electrical degree of everyday integral hours. Calculate everyday max and min three-phase voltage and the time of occurrence, daily max and min three-phase current and the time of ‘occurence. daly min three-phase power factor and the time of occurence, dally max and min three-phase active power and the time of occurrence, daily max and min three-phase reactive power and the time of ‘current, daily max and min three-phase voltage dstortion rate and the time of occurrence, dally max and ‘min three-phase current distortion rate and the time of occurrence. dally three-phase voltage on the high and low side time. daily three-phase voltage percent of pass. daly three-phase voltage distortion rate standards exceeding time. dally three-phase current dstotin rate standard-exceeding time, dally three-phase power factor les than 0.95 time, oad unbalance rate standard-exceeding time. running total time of 1-6 step capacitor input-esect times of 1-6 step capacitor, power failure moment, incoming power moment. Power {allure ties, incoming power times. daly max current value foe 15min and the time of occurance, Various control parameter functions of full digital pre-set, password, ID number (for communication), FT transformation ratio, CT transformation rato, over voltage threshold, under voltage threshold, target power factor threshold, inputresect delay, dstortion rat threshold, Clock. Compensation schemes. Inputesect codes {and capacitor capacity etc can be set ‘Communication functions: with RS232 and RS485 communication por of hardware conventions. Adopting 101 ‘or MODEBUS-RTU communication conventions. Onsite or long-deiance communication can be excuted. Can realize real time, summon various electric parameter by timing, modify control parameter and input-resect capacitance through long-distance. On ste operation through short-stance (30-50m) wireless communication function and portable computer data can be performed, With manual input-esect capacitance function, manual input and resect capacitor under the condition without voltage and current signal. Integrated protection function. JKW186 distibution monitoring compensator has functions of protecting against over voltage. Phase les. under voltage. Harmonic wave overflow et. And it can allow or forbid alarm relay drawing and closing through control parameters. ZHIYUE >>> 30 p> 2KW186 Series High Voltage Reactive Power Compensation Controller Connection drawing Installation mode Flush type and ‘guide rail type 34 <

You might also like