BASIC COMMAND MOSHELL for RNC and RBS

To check the existing signaling RNC

$ St MTP3

To check the performance parameters

RNC> pmrg m 3

See IP Address
RNC> get ethernetlink ipaddress

To see utrancell connected directedretry

RNC> get utrancell = mdn073w1 directedretry RNC> get
utrancell directedretry RNC> get utrancell directedretry
loadsharing

Check Module 10.11 RNC good or guns

RNC> mirror stat - peer disk = connected

See the second error / quality e1

RXI> lpget
Subrack = MS, Slot = 18 PlugInUnit = 1, ExchangeTerminal = 1, Os155SpiTtp = PP1,
Vc4Ttp = 1, Vc12Ttp = 60 , E1Ttp = 1

See proxy synch

RNMDN01> pr synch

To check any direction signaling connection RNC

$ Lst ranap $
get ranap $ st
ranap

Mengecheck OAM id
RNC> lk b <site Number> <Location RNC> Mis
: To Site Jamin Ginting MDN073 lk b0073MDN
for Site Jamin Ginting KBJ179 lk b3179MDN
for Rajamin Ancient Site PMR208 lk b4208PMS

mengecheck A2EA
RNC> get b <OAM id> Ex:
RNC> get B002 see numberDirection
NODE B> get aal2sp

Mengecheck proxy Aal2RoutingCase

RNC> pr Aal2RoutingCase

To check Signaling Node B

Node B> get nbap

View the status of operational E1 or guns

RXI> lst b <OAM id>, for example: lst b008
Take proxy one of his Aal2PathVccTp RXI> get <proxy>

In column view atmport his vclTpId RXI> st

AtmPort = <MS-xyz>
The result will come out, whether the port is enabled atm or Node B> st E1

Neighbor saw relations

RNC> pr gsmrelation
RNC> lpr utrancell = MDN027W1, gsmrelation

Delete / Create IMA in RXI

1.Block Aal2pathvcctp
2.U +
3.rdel (IMA) example: RXI> Irdel IMA10-1-2-3
4.U-
Script 5.Run results U-
IMA 6.lt
7.fro (IMA) example: RXI> fro IMA10-1-2-3

To see phisycal chanell / sector

corresponding
sector
RBS> lst sector = 1
RBS> get <proxy sectors>

To check the alarm:

RBS> al or
RBS> alt for the complete alarm description
...................................................................................................................................................... ... ...

Mengecheck occupation for a cell channels via RNC:

RNC> PMX mdn160w1 rrcconnect utrancell = -m 1 1 hour before, if you want 2 hours before dressing so 2

Restart RBS via MOSHELL

RBS> restartObj (Obj) Object bias in the form of Node B or PIU
RBS> acc 0 restart
...................................................................................................................................................... ... ...

Check Type RBS RBS via MOSHELL

RBS> get 0

check Synchronization
RBS> get 10

Adding Reference Synch

RBS> acl 10 RBS> RBS>
get 10
RBS> acc 10 addSyncRefResource

example:
MDN261W_Jamin_Ginting_Gg_Kebun> acc 10 addSyncRefResource

120309-14: 24: 23 10.160.64.169 7.1u RBS_NODE_MODEL_M_1_33 stopfile = / tmp /

4464 Call Action addsyncrefresource following on MOs?
================================================== ==========
=======================

10 TransportNetwork = 1, Synchronization = 1
================================================== =======================
========== Are you Sure [Y / n]? y

================================================== ==========
======================================== ============= Proxy MO
Action Nr of params
================================================== ==========
========================================
=========
====
10 Synchronization =
1 addSyncRefResource 2

Parameter 1 of 2 syncReference (moRef-ManagedObject):

Enter mo LDN:
Equipment = 1, Subrack = 1, Slot = 2, PlugInUnit = 1, ExchangeTerminal = 1, E1PhysPathTerm
= p <2, PlugInUnit = 1, ExchangeTerminal = 1, E1PhysPathTerm = pp2

Parameter 2 of 2 syncPriority (long): 2

> > > Return value = null

================================================== ==========
======================================== ============= Total: 1 MOs attempted, 1
MOs actioned

MDN261W_Jamin_Ginting_Gg_Kebun>

Block
RBS> bl 5 5 is a proxy when we do pr or lst of what we load (lt). Command bl able to block some boards at
once. RBS> bl 5 6 9 block board on the proxy 5, 6, 9 RBS> bl 5-12 block board on the proxy 5-12

unblock Board
RBS> deb 5

Block Iub
RNC> lbl Iub
Example: block Iub Jamin Ginting Node B and RNC> lbl
b0073MDN

unblock Iub
RNC> ldeb Iub ...
Look
RNC> get vc trafficdes
Block Cell
RNC> lbl <Cell Id>
Example: block cell Node B and RNC Jamin Ginting> lbl
MDN073W

unblock Iub
RNC> ldeb <Cell Id>

See Cross conecction VC

RNC> get cross vc

To see all the status of the disabled MO

RNC> st all dis

...................................................................................................................................................... ... ...

View the status of board
RBS> cab or RBS> cabx more detail
....................................................................................................................................
.................. ... ...
View the status / site name
RBS> get to see the complete status of the following parameters
RBS> get 0 to view the status and type of RBS
....................................................................................................................................
.................. ... ...
Me-Load an
object
Object bias in the form of antenna, feeder, RBS,
RBS> lt (Managed Object) radio, etc
....................................................................................................................................
.................. ... ...

See Licensekey Node B

Rbs> cat
/c/license/licensekeys.xml

Seeing the desired board

RBS> lhsh aabbcc vii bias command form, te log read, llog, ps port,
(command) reload / restart
aa: SMN; bb: APN; cc:
default 00
For example:
to view the status of
RBS> lhsh 000 800 vii Rax
RBS> lhsh 010 400 reload to reload TRX
RBS> 010 600 lhsh restart to restart AIU
RBS> lhsh 010 view the status of
200 / port_0_dev_12 vii MCPA
RBS> lhsh 010
600 / port_0_dev_17 restart restart ASC
RBS> lhsh 010
600 / port_0_dev_17? ASC command help
RBS> lhsh 010 help command
200 / port_0_dev_12? MCPA
to search
RBS> lhsh xxxxxx ps more
...................................................................................................................................................... ... ...
Saw logs Alarms
RBS> te log read or RBS> ter or RBS> llog restart status If you want to
sort the desired status, add | grep ... RBS> te log read | grep clock
view the status of any clock RBS> te log read | grep error
view the status of any error
RBS> te log read | grep faulty RBS> te help
help command te

If using the command lt, it will display a confirmation, select Y, then beat the pr command or lst.
RBS> 2005-03-20 LGS RBS>
lgasmi 30 RBS> 5h lgaevs
RBS> lgac 30m

...................................................................................................................................................... ... ...

See HSDPA per cell

RNC> CED

To see Proxy
RBS> pr
To see the detailed status, use the command get.
...................................................................................................................................................... ... ...
Viewing configuration version (CV)
RBS> cvls CV status last saw RBS> cvms
to create and set a new CV
...................................................................................................................................................... ... ...
See radiolink ID and radio channel occupation status
RBS> RBS radio lt> get no
radio
...................................................................................................................................................... ... ...
If you want to change a parameter, use the command set Example: to change the delay and
attenuation feeder
RBS> lt feeder
RBS> get antfeedercable RBS> get
(proxy)
RBS> set (no proxy) dl attenuation xxxxxxxxxxxx for setting att in the downlink direction x =
a new value (12x)
...................................................................................................................................................... ... ...
See if there is interference in the TRX or sector
RBS> 010 400 te lhsh clear log deleting old log on TRX sector 1 (010400) RBS> lhsh 010 400 te e trace3

trxMeasIntLevelC immediately disable, then RBS> lhsh 010 400 te log read

lh mod celldata -cid utrancellnya41413

...................................................................................................................................................... ... ...
See radio channel occupation
RBS> RBS radio lt> get no
radio
...................................................................................................................................................... ... ...
Choosing a CV that is used when startable
RBS> cvset (name CV)
...................................................................................................................................................... ... ...
Adding Route
At the prompt DOC C: route print
...................................................................................................................................................... ... ...
TxDeviceG faulty
1.
Site> Lt tx
Site> Get TxDeviceGroup Change
See cabx
loadHs false if txHs loadHs = true
loadHs proxyxxx set false
/ True
2.
Change CV
Cvls.
Cvms <cvname> [<carrier>] [<comment>] Cvcu see cv reply active

...................................................................................................................................................... ... ...

Read the log file
lhsh 001 200 / port_8_dev_6 te log read read log files
...................................................................................................................................................... ... ...
Average RSSI and Transmitted Carrier Power
$ pmr
<= AvgRssi - 80.00 Good
...................................................................................................................................................... ... ...
check TMA
RBS> TMA lt RBS>
get TMA
...................................................................................................................................................... ... ...
LNA Disabled in ASC
10.149.14.105> lhsh 001 200 / port_9_dev_19 ASC lnaerr $
lhsh 001 200 / port_9_dev_19 ASC lnaerr ERROR: LNA branch
A, one faulty transistor LNA transistors branch B OK

10.149.14.105> lhsh 001 200 / port_9_dev_19 ASC lnaerrset lhsh

001 200 na / na port_9_dev_19 lnaerrset ASC No. LNA transistor
faults set for branch A

10.149.14.105> lhsh 001 200/001 200 lhsh port_5_dev_17

lnaerr ASC / ASC lnaerr port_5_dev_17 transistors LNA LNA
transistors branch A branch B OK OK

...................................................................................................................................................... ...
check OBIF
RBS> lt all RBS> cabx
RBS> get OBIF RBS>
get optical

...................................................................................................................................................... ... ...

Check the status of the sector
RBS utrancell lt> lt
all RBS> pr fach

Clock SET NODE B

RBS> setclock yyyy-mm-dd hh: mm: ss eg:

RBS> setclock 2006-10-26 18:39:00

Print Out Clock
RBS> Readclock
...................................................................................................................................................... ... ...
Change antennaSupervisionThreshold
RBS> RBS antenna lt> get
Antenna
RBS> set antennaSupervisionThreshold 20 (if 0 then VSWR not supervised)
............................................................................................................... .......................................... ...
Seeing the transmission status
In EMAS RNC, if site A down E1 should be red. However, if site A and LED E1 down green, it must be because in
the loop to the RNC.

In Moshell RNC, lt E1 and lst, if the site has been down and Op disable state, the TRS problem (open), but if
Op enable state, the TRS loop to the RNC.

Check E1.
MoShell> lst ImaGroup = ES-2-2-1 dis MoShell> lk
<ImaLink proxy #> phy
MoShell> lpr Subrack = ..., Slot = .., PlugInUnit = 1, Etmc41 = 1, Os155SpiTtp = PP1, Vc4 ..... MoShell> lpget
<PhyPath MO proxy #>

RNC> lt all
RXMDN02> for ever
Enter commands (one per line), then type "done"
> PGET 685 687 689 691 ice
> PGET 685 687 689 691 UAS
> wait 1800
> done ((to check the performance site in E1, see the value, is there any counter in every time? if yes,
the performance is going to worse, if the value is stable, the performance is OK) RNC> PGET es1-2- 1
(see Value pmReceivedAtmCells, pmSecondsWithUnexp, pmTransmittedAtmCells)

Error VC ete Loss of Connectivity AAL5 hang

$ Get AAL5

$ 4 continuityCheck set to false (if True tried on false ... then be returned again to the starting
position) $ set 4 continuityCheck true

Check Kelerusan E1
RXMDN02> strt check the first and second VC (if any) RXMDN02> lt vc

RXMDN02> lacc atmport = es1-24-17 2193 eteloopback AtmPort = ES1-24-17, VplTp =

VP1, VpcTp = 1, VclTp = vc32 eteLoopBack 0
> > > Return value = false

Or via EM RNC equipment select MS or ES continue to select the VC to XX ... find E1 keXX
................................................................................................ ......................................................... ...
Check E1 from RXI
RXI> lt AAL2
RXI> lst iublink

RXI> lt all
RXI> lst imagroup = xxxx (form vclTpId copy of MS-16-1-IMA3)
RXI> get porxy
...................................................................................................................................................... ... ...
View the status of RBS that is available
RNC> str
RNC> -I str 1003 see RBS 1003 RNC> lt utrancell
RNC> get utrancell
RNC> lst utrancell
RNC> set (no proxy) primaryCpichpower (value) per 3 dB max.
...................................................................................................................................................... ... ...
Seeing RNC ok or not
RNC> std
...................................................................................................................................................... ... ...
Seeing the error code cell
RNC> tg
...................................................................................................................................................... ... ...
Troubleshooting Viewing the status of E1
Web> lt E1 site>
PGET e1 ice RNC> lst

...................................................................................................................................................... ... ...

Change Cell ID
RNMDN02> RNMDN02 cell lt> lt RNMDN02
cell = 0920> get RNMDN02 local cell =
0920> get cell = 0920

RNMDN02> 1489 set localCellId = 9201

...................................................................................................................................................... ... ...
Block / CD12 Cell DeBlock IUBLINK
RNMDN02> lt cell
RNMDN02> get {IUBLINK} / Cell ID RNMDN02> lst {IUBLINK} / Cell ID
RNMDN02> bl {proxy} to block RNMDN02> deb {proxy} to deblock
RNMDN02> lbl {IUBLINK} CD12 on the block once RNMDN02> ldeb
{IUBLINK} CD12 in deblock at once

...................................................................................................................................................... ... ...

Block / DeBlock Sector - Utrancell
RNMDN02> lbl {utrancell} all sectors on the block once
RNMDN02> lbl {utrancell1} sector1 only in block RNMDN02> ldeb
{utrancell} all sectors in deblock at once RNMDN02> ldeb
{utrancell1} sector1 only in deblock

...................................................................................................................................................... ... ...

RetDevice_RetNotCalibrated
lt lst ret
ret
acl <proxy>
actc <proxy> forceCalibration ( do it twice)

loop commen
RNMDN02> for ever
RNMDN02> strt RNMDN02>
5 RNMDN02> done

...................................................................................................................................................... ... ...

Check Traffic and HSDPA
$ Lt $ get
Radio radio
$ Lt IubDataStreams
$ get
IubDataStreams

For detail information

$ Mom all noOfCommonStreams

...................................................................................................................................................... ... ...
Check all IMSI list
RNMDN02> ueregprint all see that inactive IMSI
RNMDN02> uer (xxxIMSIXXX) all check the status of
the IMSI
RNMDN02> uer check all the IMSI used data or complete Voic radio with ling
......................................................................................................... ................................................ ... Test
VSWR etc.

RBS> lhsh 001 200 / port_1_dev_16 asc

...................................................................................................................................................... ... ...
See the list of
software RNC
U / Trace - check software RNC u / target monitor handle = 43 (default handle = 42)
RNMDN02> pglist

RNMDN02> pgload CXC1326054_R1D01 - if not already active, load the software 43 in RNC
RNMDN02> pgstart 43 - to activate the software 43 which has been loaded RNMDN02> pgkill
43

RNMDN02> bo - board at the RNC list u / viewed GPB which will be monitored RNMDN02> lhsh 011
300 te enable bus_send bus_receive RANAP * - ie GPB in Extension subrack and in the slot 13, and
we only monitor its course RANAP NB.

> lhsh 011 300 te enable bus_send bus_receive NBAP *

> lhsh 011 300 te enable bus_send bus_receive PRC *
> ueenable IMSI (XXXXXXimsi number) bus_send bus_receive NBAP
> ueenable IMSI <IMSINUMBER> bus_send bus_receive
Location s / w decoder
[~ / Moshell] $ ls -l

How Chack All Calls Track

[~ / Moshell] $ monitor6054.exe 10.24.20.9 011 300 -nolocal | decoder / decoder.pl | de coder / flow.pl -colour

KILL S / w to 43 $
pgkill 43
...................................................................................................................................................... ... ...
RXI
See Lk rxi AAL2 at .4702

...................................................................................................................................................... ... ...

AAL2RoutingCase in Node B
When making changes to make cv (CVMR)
1.$ lt aal2sp
2.$ lt aal2routingcase (see A2EA)

$ Get aal2routingcase
3.Check / and equate in RXI also in the
RNC $ lt aal2routingcase
$ Get aal2routingcase = A2EA (ie get aal2routingcase = 620,000,100,405,232)
When the difference and will make changes On Node B

1.
$ Set 1 A2EA 620,000,100,402,999 (value 999 Dummy)
2.
at RXI
$ Rset 159 numberDirection 620,000,100,402,999 (value 999 Dummy)
...................................................................................................................................................... ... ...

CREATE CROSS CONNECT NBAPCOMMON in RXI

RXI901> cr TransportNetwork = 1, AtmCrossConnection = b7ca

Attribute 1 of 2 vclTpAId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-26-1, VplTp = VP6, VpcTp = 1, VclTp = vc36 #vclTpAId

Attribute 2 of 2 vclTpBId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-3-ima1, VplTp = VP1, VpcTp = 1, VclTp = vc36 #vclTpBId

> > > [Proxy ID = 135] MO

name: ManagedElement = 1, TransportNetwork = 1, AtmCrossConnection = b7ca

RXI901> cr TransportNetwork = 1, AtmCrossConnection = b7cb

Attribute 1 of 2 vclTpAId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-26-1, VplTp = VP6, VpcTp = 1, VclTp = vc43 #vclTpAId

Attribute 2 of 2 vclTpBId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-3-ima1, VplTp = VP1, VpcTp = 1, VclTp = vc43 #vclTpBId

> > > [Proxy ID = 136] MO

name: ManagedElement = 1, TransportNetwork = 1, AtmCrossConnection = b7cb

Create VC

RXMDN02> cr TransportNetwork = 1, AtmPort = IMA14-61-62-63, VplTp = VP1, VpcTp = 1, VclTp = vc51

090207-19: 37: 30 10.160.64.105 7.1-CPP5.1.2.28_3 CPP_MOM_MOM stopfile = / tmp / 25 589

Attribute 1 of 2 externalVci (long): 51 #externalVci

Attribute 2 of 2 atmTrafficDescriptorId (moRef: AtmTrafficDescriptor):

Enter mo LDN: AtmTrafficDescriptor = U42 #atmTrafficDescriptorId

> > > [Proxy ID = 5234] MO name: ManagedElement = 1, TransportNetwork = 1, AtmPort = IMA14-6162-63,
VplTp = VP1, VpcTp = 1, VclTp = vc51

RXMDN02> lset TransportNetwork = 1, AtmPort = IMA14-61-62-63, VplTp = VP1, VpcTp = 1, VclTp = vc51 $
userLabel VclTp vc51

090207-19: 37: 30 10.160.64.105 7.1-CPP5.1.2.28_3 CPP_MOM_MOM stopfile = / tmp / 25 589

================================================== ==========
======================================== ========
id MO userLabel Result
================================================== ==========
======================================== 5234 ======== AtmPort = IMA14-61-62-63,
VplTp = VP1, VpcTp = 1, VclTp = vc51
- - > VclTp vc51 >>>
Set.
================================================== ==========
========================================
======== Total: 1 MOs attempted, 1 MOs set

Nambahin Synch in Node B

LHK114W_Air_Bersih_Kutablang_BSC> st e1

090312-21: 27: 11 10.164.25.41 7.0 RBS_NODE_MODEL_J_5_17 stopfile = / tmp / 4352

================================ ============================
====================== = Proxy Adm State Op. State MO

================================================== ==========
======================= 145 1 (UNLOCKED) 1 (ENABLED)

Equipment = 1, Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, ExchangeTerminal = 1, E1PhysPathTerm =

PP3 146 1 (UNLOCKED) 1 (ENABLED)
Equipment = 1, Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, ExchangeTerminal = 1, E1PhysPathTerm =
pp2 147 1 (UNLOCKED) 1 (ENABLED)
Equipment = 1, Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, ExchangeTerminal = 1,
E1PhysPathTerm = PP1 =======================
===================================== ============= ========== Total: 3
MOs

LHK114W_Air_Bersih_Kutablang_BSC> acl synch

090312-21: 27: 46 10.164.25.41 7.0 RBS_NODE_MODEL_J_5_17 stopfile = / tmp / 4352

================================================== ==========
======================================== ============= Proxy MO
Action Nr of params
================================================== ==========
======================================== 975
============= Synchronization = 1
addSyncRefResource 2
975 Synchronization = 1 changeSyncRefPriority 2
975 Synchronization = 1 removeSyncRefResource 1
975 Synchronization = 1 resetLossOfTracking 1
1101 RbsSynchronization = 1 switchMasterTu 0
================================================== ==========
======================================== =============

LHK114W_Air_Bersih_Kutablang_BSC> acc 975 addSyncRefResource

090312-21: 28: 21 10.164.25.41 7.0 RBS_NODE_MODEL_J_5_17 stopfile = / tmp /
4352 Call Action addsyncrefresource following on MOs?
================================================== 975
======================= ========== TransportNetwork = 1, Synchronization = 1

================================================== =======================
========== Are you Sure [Y / n]? y

================================================== ==========
======================================== ============= Proxy MO
Action Nr of params
================================================== ==========
======================================== 975
============= Synchronization = 1
addSyncRefResource 2

Parameter 1 of 2 syncReference (moRef-ManagedObject):

Enter mo LDN:
Equipment = 1, Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, ExchangeTerminal = 1, E1PhysPathTerm = pp2

Parameter 2 of 2 syncPriority (long): 2

> > > Return value = null

================================================== ==========
======================================== ============= Total: 1 MOs attempted, 1
MOs actioned

LHK114W_Air_Bersih_Kutablang_BSC> get synchro

090312-21: 28: 46 10.164.25.41 7.0 RBS_NODE_MODEL_J_5_17 stopfile = / tmp / 4352

================================ ============================
====================== 975 ===============================

TransportNetwork = 1, Synchronization = 1
================================================== ==========
========================================
============= SynchronizationId
1
0
degradationIsFault (DEGR_NOT_FAULT)
syncRefActivity i [8] = 2 1 1 1 1 1 1 1
syncRefPriority i [8] = 1 2 0 0 0 0 0 0
i [8] = 3 3 0 0 0 0 0
syncRefStatus 0
syncReference [8] =
> > > syncReference =
Equipment = 1, Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, ExchangeTerminal = 1, E1PhysPathTerm = PP1
> > > syncReference =
Equipment = 1, Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, ExchangeTerminal = 1, E1PhysPathTerm = pp2
> > > syncReference =
> > > syncReference =
> > > syncReference =
> > > syncReference =
> > > syncReference =
> > > syncReference =
systemClockA 2 (LOCKED_MODE)
systemClockB 7 (NOT_APPLICABLE)
userLabel
================================================== ==========
========================================
============= 1101
NodeBFunction = 1, RbsSynchronization = 1
================================================== ==========
========================================
============= RbsSynchronizationId
1
masterTu 1 (PLUG_IN_UNIT_REF1)
nodeIsStable true
nodeIsSynchronized true
plugInUnitRef1 Subrack = 1, Slot = 1, PlugInUnit = 1
plugInUnitRef2
timDeviceRef1
Subrack = 1, Slot = 1, PlugInUnit = 1, CBU = 1, TimDeviceSet = 1, TimDevice = 1 timDeviceRef2

================================================== ==========
======================================== ============= Total: 2 MOs

...................................................................................................................................................... ... ... CV

Inventory RNC> l +

==> start a log file

RNC> inv ==> check inventory RNC
RNC> l- ==> put an end to the log file.

...................................................................................................................................................... ... ...

HSDPA for check maxHsRate
RBS> lt IubDataStreams RBS> get
IubDataStreams maxHsRate
15 for 1 E1
...................................................................................................................................................... ... ...
(4 commands below are to be executed on RNC when the Heartbeat Failure on RNC only )

Telnet or moshell to the RNC.

We only have a few minutes to execute the command before the JVM recovered. Your help is appreciated.

RNC> capi tot lhsh RNC 001 200> 001

200 (About 2 minutes of logs displayed on screen)
capi type lhsh pri
RNC> lhsh 001 200 30 RNC capi type
pri> lhsh
001 200 ps -bw JVM
...................................................................................................................................................... ... ...

check Temp

$ Lh fui ru get temp

...................................................................................................................................................... ... ...
alarm Log
$ Iga
$ Lgasmi 30
...................................................................................................................................................... ... ...
.......................................................................................................................................... ............... ...
.............................................................................................................................. ........................... ...

VSWR
$ Lh fui ru get VSWR
...................................................................................................................................................... ...... ..

Type Command to determine the RNC

$ Get 0

Knowing what type of board in the RNC

RNC> bo

knowing inventory
RNC> inv

Know the board is active, standby, including board temperature

RNC> cab

Knowing that terdefine E1 ports on RNC

$ stt

Knowing Iub link to Node B terdefine where

$ IFI

Resume the number of occupied channels

$ uer

See history Command

$ HC

See Status Cell

$ str

See All conection

$ lst

See All Node B, RNC

$ str

See All Node B, RNC along with ATM port

$ strt

View the status of devices in the RNC

$ std

Viewing proxy
$ pr

See Iublink used in RNC

RNC> lk iublink <Iub> RBS> lk
Iub <Iub>

To check the data packet router (pdr)

RNC> get packetdatarouter

To see all disable MO

RNC> st all dis

Check the status of the disabled equipment

RNC> st equip dis

See all the disabled mo

RNC> st all 1 * 0

See all mo blocked

RNC> st all ^ 0

Scrambling CEK CODE / PNCODE

RNMDN02> lt all
RNMDN02> get all primaryScramblingCode Or:

RNMDN02> get utrancell = 4184 primaryScramblingCode - For one cell

..................................................................................................................... .................................... ...
CHECKS PARAMETERS OF CELL
RNC1> lt utrancell RNC1>
get 13 091 1309 cell sector 1
...................................................................................................................................................... ... ...
STATUS CHECKS crossconnect
RXI >> STC 2051 -> show all crossconnections where the information matches "2051" (in the case below, where
the atmport is 2051)

RXI >> STC. * 0 -> show all crossconnections that are disabled.
...................................................................................................................................................... ... ...
STATUS CHECKS IubLink
RNMDN02> lst .1040
...................................................................................................................................................... ... ...
CELL STATUS CHECKS
RNMDN02> str | grep 1040
...................................................................................................................................................... ... ...
CELL STATUS CHECKS
RNMDN02> lst .MDN524W
...................................................................................................................................................... ...
CEK Interference
RNJKT01> TGD cell = 51 361 ulinterference celldata 5136 cell sector 1
Or:
RNJKT01> cid dyncelldata 51 361

CEK ULINTERFERENCE

RCN> TGD cell ulinterference

...................................................................................................................................................... ... ...
Check HSDPA:
$ Lt iubdata
$ Get IubDataStreams Check
Exp:

IubDataStreamsId 1
maxHsRate 60
noOfCommonStreams 14
noOfDedicatedStreams 17
userLabel

noOfCommonStreams = n * 4
maxHsRate 15 = 1E1

description mom all maxHsRate

...
...
Tracert IP or OAM problem

Get .iub lst proxy Lacc

eteloopback

...................................................................................................................................................... ... ...

KILL JVM RNC

IP TELNET RNC $ lhsh 001 200

pglist -e
$ Lhsh 001 200 pgkill 8 (List No. 8 handle Java)

...................................................................................................................................................... ... ... Tracert

...................................................................................................................................................... ... ...

HOW TO REMOVE THE BOARD AND REPLACE WITH DIFFERENT BOARD:

* For remove and delete the board from NODE:

1. Lock the board
2. Go to Software allocation -> Right click on property
3. Move the software for the board that want to remove from right to left
4. Go to Equipment and select the board -> Right click and Delete

* For Add the new board to NODE:

1.Go to software allocation -> Right click on property
2.Add the new software board from left to right
3.Go to moshell -> do command -> lt all
- - > Pr managed
- - > Get 1
- - > See AutoConfiguration allow -> the state should be TRUE
4.Plug-in the new board.
5. Restart the new board and wait until the board synchronize to the NODE
......................................................................................................... ................................................ ... HOW
TO UPGRADE SOFTWARE
FROM RBS and RNC OSS

1.Install the Upgrade Package software to OSS, dont forget to unzip the files in the OSS with the command:

- - > unzip <Name_of_file>

2.Run RANOS (WCDMA RAN OSS Explorer) -> GO to Configuration menu -> chose Hardware and Software
management -> choose
SMO
3.Go to software in the SMO menu, choose the software -> right click choose Synhcronize CPP SW Package

4.Go to the Network menu -> Find RBS or RNC that want to upgrade -> right click and choose Upgrade

5.Choose a software upgrade and click next

6.Dont thick the "Use associated software FTP service for each NE" and choose "UTRAN SOFTWARE"

7.In TAB Jobs Configuration -> Thick the 2 upper point -> Installation (Immediate)
- - > Verify Upgrade (Manual)
8.Click NEXT and in this parameter and choose Software Installation In transfer-type load module choose FULL

9.Go to JOBS menu and see the progress / log of Install Software (wait until it shows the activity install
complete) activity after install complete
10.Go to NE Thread again, right click and select Start NE Threads -> this activity will upgrade the node go
to JOBS menu and see the progress / log of Upgrade (wait until it shows the complete upgrade activity)

11. After the upgrade complete back-to netwroks menu right click and choose ADJUST
12. In thick adjust menu All Filters and Jobs scheduling Immediate
13. Go to JOBS menu and see the log, wait until Adjust activity complete
14.Go to network menu Choose RBS or RNC want to upgrade, right click choose Upgrade.
15. In Jobs Configuration Thick Upgrade "Immediate", Confirm Upgrade "Manual" and SWAdjust "Manual"

16. TAB choose Reboot Node upgrade Upgrade

17. See progress in Jobs menu

18. If a complete upgrade activity go to NE Threads -> choose the NODE and right click and choose Start NE
Thread

19. Go back again to the NE Threads to verify the Software Adjustment by right click and choose NE Thread
start again

20. FINISH UPGRADE ACTIVITY

IP mentrace OAM:

traceroute <IP>
/ CREATE SOME CROSS IN RXI connects FOR THE

NBAPCOMMON RXI901> cr TransportNetwork = 1,

AtmCrossConnection = b7ca
Attribute 1 of 2 vclTpAId (moRef: VclTp):
Enter mo LDN: AtmPort = MS-26-1, VplTp = VP6, VpcTp = 1, VclTp = vc36 #vclTpAId

Attribute 2 of 2 vclTpBId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-3-ima1, VplTp = VP1, VpcTp = 1, VclTp = vc36 #vclTpBId

> > > [Proxy ID = 135] MO

name: ManagedElement = 1, TransportNetwork = 1, AtmCrossConnection = b7ca

RXI901> cr TransportNetwork = 1, AtmCrossConnection = b7cb

Attribute 1 of 2 vclTpAId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-26-1, VplTp = VP6, VpcTp = 1, VclTp = vc43 #vclTpAId

Attribute 2 of 2 vclTpBId (moRef: VclTp):

Enter mo LDN: AtmPort = MS-3-ima1, VplTp = VP1, VpcTp = 1, VclTp = vc43 #vclTpBId

> > > [Proxy ID = 136] MO

name: ManagedElement = 1, TransportNetwork = 1, AtmCrossConnection = b7cb

Pindahin Node B and RNC to another Module

RNMDN01> get b0194MDN

090317-10: 41: 04 10.160.64.17 7.0 RNC_NODE_MODEL_G_5_30 stopfile = / tmp / 3780

================================ ============================
====================== =============================== 20034

RncFunction = 1, IubLink = b0194MDN

================================================== ==========
========================================
============= IubLinkId
b0194MDN
availabilityStatus 0 (NO_STATUS)
beMarginDlHw 0
beMarginUlHw 0
dlHwAdm 99
operationalState 1 (ENABLED)
preferredSubrackRef Subrack = MS
rbsId 194
reservedBy [3] =
> > > reservedBy = RncFunction = 1, UtranCell = MDN194W1
> > > reservedBy = RncFunction = 1, UtranCell = MDN194W2
> > > reservedBy = RncFunction = 1, UtranCell = MDN194W3
rncModuleRef RncModule =
1
ulHwAdm 99
userLabel IubLink b0194MDN
================================================== ==========
======================================== ============= Total: 1 MOs
RNMDN01> 20034 set preferredSubrackRef Subrack = MS