Scribd
Upload
1K views2 pages

Iso 10511 Nut Dimensions - Ref

This document provides product standards for metric nylon insert locknuts in stainless steel. It specifies dimensional, mechanical, performance, and chemical requirements according to ISO standards for various nut sizes. Suppliers must meet all requirements specified in order to be approved, and corrective action may be required if products do not meet standards. Revision levels and rationale for changes to the document standards are recorded on the last page.

Uploaded by

kumarkk1969
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views2 pages

Iso 10511 Nut Dimensions - Ref

This document provides product standards for metric nylon insert locknuts in stainless steel. It specifies dimensional, mechanical, performance, and chemical requirements according to ISO standards for various nut sizes. Suppliers must meet all requirements specified in order to be approved, and corrective action may be required if products do not meet standards. Revision levels and rationale for changes to the document standards are recorded on the last page.

Uploaded by

kumarkk1969
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2 Fastenal Product Standard REV-00

Date: November 21, 2018 M.NYLK.10511.A2

Metric, Nylon Insert Locknut, ISO 10511, A2-035 Stainless Steel


This product standard contains the required dimensional, mechanical, performance, and chemical characteristics of the products shown
in this purchase order (as applicable to the product). Unless specified below, current revisions of national or international standards
shall be applicable as of the date of Fastenal’s purchase order and must be adhered to in their entirety. If the order received does not
meet these requirements, corrective action may be issued which could jeopardize your status as an approved supplier to Fastenal.

h m s
Hex Width Across
Size Thickness
Height Flats
Min. Max. Min. Min. Max.
M3 3.42 3.90 1.55 5.32 5.50
M4 4.52 5.00 1.95 6.78 7.00
M5 4.52 5.00 2.45 7.78 8.00
M6 5.52 6.00 2.90 9.78 10.00
M8 6.18 6.76 3.70 12.73 13.00
M10 7.98 8.56 4.70 15.73 16.00
M12 9.53 10.23 5.70 17.73 18.00
M14 10.22 11.32 6.42 20.67 21.00
M16 11.32 12.42 7.42 23.67 24.00
M20 13.10 14.90 9.10 29.16 30.00
M24 16.00 17.80 10.90 35.00 36.00
M30 20.10 22.20 13.90 45.00 46.00
M36 23.40 25.50 16.90 53.80 55.00

RECORD OF REVISION CHANGES TO THIS DOCUMENT ARE LOCATED ON THE


LAST PAGE
Page 2 of 2 Fastenal Product Standard REV-00

Date: November 21, 2018 M.NYLK.10511.A2

Specification Requirements:

• Dimensions: ISO 10511


• Threads: 6H
• Material &
Mechanical Properties: A2-035 per ISO 3506-2
Nylon 6/6 material shall be in compliance with
current RoHS European Union Directive
• Prevailing Torque: Per Fastenal QA7-96 Metric Stainless Steel Locknut Test
• Finish: Per ASTM A380/A380M
• Material Test Reports: The MTR must have documented lot traceability, dimensional
results, full chemical test results and full mechanical test
results to the specification(s) above. In addition, the MTR
shall be in full compliance with Fastenal’s MTR
Requirements.

Revision Level Changes to this Document

Revision Revision
Document Name Rationale for Revision
Level Date
M.NYLK.10511.A2 00 11/21/2018 Original document

The rationale above may not include all of the changes within each revision. A complete
review of the Fastenal Product Standard is required.

You might also like