For DENSO Authorized

ECD Service Dealer Only

Diesel Injection Pump

No. E-03-02

SERVICE MANUAL
Common Rail System for ISUZU
6HK1/6SD1 Type Engine
Operation
June, 2003

00400018
GENERAL
The common rail system was designed for electronic control of injection quantity, injection tim-
ing and injection pressure to obtain optimal operational control.

Features
• Lower exhaust gas and higher output due to high pressure injection in all usage ranges.
• Reduction in noise and exhaust gas due to injection rate control.

om
• Improved performance due to increased flexibility in the injection timing setting.
• Independent control of injection pressure in response to engine speed and load.

l.c
ua
an
Main Elements

irm
Total
Cylinder

pa
Manufacturer Vehicle Model Engine Model Displacement
Configuration

re
(cc)

e-
6HK1 7,800

ic
rv
ISUZU Forward 6SD1 se Straight 6 9,800
6WG1 15,600
1. Outline
1.1 System Outline
This system also provides the following functions:

om
• A self-diagnosis and alarm function using computer to diagnose the system’s major
components and alert the driver in the event of a problem.

l.c
ua
• A fail-safe function to stop the engine, depending upon the location of the problem.

an
• A backup function to change the fuel regulation method, thus enabling the vehicle to

irm
continue operation.

pa
1.2 System Configuration

re
Divided by function, the system can be classified according to the fuel system and the control

e-
system.

ic
[1] Fuel System

rv
se
High-pressure fuel that is generated by the supply pump is distributed to the cylinders using a
rail. Electromagnetic valves in the injectors then open and close the nozzle needle valve to con-
trol the start and end of fuel injection.

Electronic
control
Solenoid valve to control
the needle lift

Discharge
volume
Fuel tank Supply pump Rail Injector

Q000080E

[2] Control System

Based on the signals received from various sensors mounted on the engine and the vehicle,
the ECU controls current timing and the duration in which the current is applied to the injectors,
thus ensuring an optimal amount of fuel is injected at an optimal time.
The control system can be broadly classified according to the following electronic components:
sensors, computers, and actuators.

Sensors Computers Actuators

(Accelerator opening)
Accelerator sensor
Injectors
(Engine speed)
NE sensor
(Crankshaft position sensor)
(Fuel
and injection timing control etc.)
injection quantity

Cylinder
TDC sensor
( recognition signal )
ECU
Rail
(Cylinder recognition sensor)

Supply pump
Other sensors and switches
(Fuel pressure control)
Q000081E

1
 Diesel Injection Pump

SERVICE MANUAL

COMMON RAIL SYSTEM (CRS)

om
l.c

OPERATION
ua
an
irm

September, 2007
pa
re
e-
ic
rv
se

00400534E
 om
l.c
ua
an
irm
pa
re
e-
ic
rv
se

© 2007 DENSO CORPORATION

All Rights Reserved. This book may not be reproduced
or copied, in whole or in part, without the written
permission of the publisher.
 Revision History

Revision History
Date Revision Contents
2007. 09 • SCV: Explanation of compact SCV added to "Suction Control Valve (SCV)". (Operation: Refer
to page 1-30.)

om
• "Repair" section added.

l.c
ua
an
irm
pa
re
e-
ic
rv
se
 Table of Contents

Table of Contents
Operation Section

1. GENERAL DESCRIPTION
1.1 Changes In Environment Surrounding The Diesel Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 Demands On Fuel Injection System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

om
1.3 Types Of And Transitions In ECD (ELECTRONICALLY CONTROLLED DIESEL) Systems . . . . . . . . . . . . . . 1-3
1.4 Common Rail System Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

l.c
ua
1.5 Common Rail System And Supply Pump Transitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

an
1.6 Injector Transitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

irm
1.7 Common Rail System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

pa
2. COMMON RAIL SYSTEM OUTLINE

re
2.1 Layout of Main Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

e-
ic
rv
3. SUPPLY PUMP DESCRIPTION se
3.1 HP0 Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
3.2 HP2 Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
3.3 HP3 Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27
3.4 HP4 Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-41

4. RAIL DESCCRIPTION
4.1 Rail Functions and Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-46
4.2 Component Part Construction and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-46

5. INJECTOR DESCRIPTION
5.1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-50
5.2 Injector Construction and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-51
5.3 Injector Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-54
5.4 Injector Actuation Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-54
5.5 Other Injector Component Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-56

6. DESCRIPTION OF CONTROL SYSTEM COMPONENTS

6.1 Engine Control System Diagram (Reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-59
6.2 Engine ECU (Electronic Control Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-60
6.3 EDU (Electronic Driving Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-60
6.4 Various Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-61

7. CONTROL SYSTEM
7.1 Fuel Injection Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-66
7.2 E-EGR System (Electric-Exhaust Gas Recirculation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-76
7.3 Electronically Controlled Throttle (Not Made By DENSO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-78
7.4 Exhaust Gas Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-79
7.5 DPF System (Diesel Particulate Filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-80
7.6 DPNR SYSTEM (DIESEL PARTICULATE NOx REDUCTION). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-82
 Table of Contents

8. DIAGNOSIS
8.1 Outline Of The Diagnostic Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-83
8.2 Diagnosis Inspection Using DST-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-83
8.3 Diagnosis Inspection Using The MIL (Malfunction Indicator Light) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-84
8.4 Throttle Body Function Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-86

9. END OF VOLUME MATERIALS

9.1 Particulate Matter (PM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-87
9.2 Common Rail Type Fuel Injection System Development History And The World’s Manufacturers. . . . . . . . . 1-87
9.3 Higher Injection Pressure, Optimized Injection Rates, Higher Injection Timing Control Precision, Higher Injection
Quantity Control Precision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-88
9.4 Image Of Combustion Chamber Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-90

Repair Section

1. DIESEL ENGINE MALFUNCTIONS AND DIAGNOSTIC METHODS (BASIC KNOWL-

EDGE)
1.1 Combustion State and Malfunction Cause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-91
1.2 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92

2. DIAGNOSIS OVERVIEW
2.1 Diagnostic Work Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93
2.2 Inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94
2.3 Non-Reoccurring Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96

3. DTC READING (FOR TOYOTA VEHICLES)

om

3.1 DST-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98

l.c

3.2 DTC Check (Code Reading via the DST-2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98

ua

3.3 DTC Memory Erasure (via the DST-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98

an
irm

4. TROUBLESHOOTING BY SYSTEM
pa

4.1 Intake System Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-99

re

4.2 Fuel System Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-99

e-

4.3 Basics of Electrical/Electronic Circuit Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-102

ic
rv
se

5. TROUBLESHOOTING
5.1 Troubleshooting According to Malfunction Symptom (for TOYOTA Vehicles). . . . . . . . . . . . . . . . . . . . . . . . 2-107
5.2 Other Malfunction Symptoms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-122

6. DIAGNOSIS CODES (DTC)

6.1 DTC Chart (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-124
 Operation Section
1– 1

1. GENERAL DESCRIPTION

1.1 Changes In Environment Surrounding The Diesel Engine

z Throughout the world, there is a desperate need to improve vehicle fuel economy for the purposes of preventing global
warming and reducing exhaust gas emissions that affect human health. Diesel engine vehicles are highly acclaimed in
Europe, due to the good fuel economy that diesel fuel offers. On the other hand, the "nitrogen oxides (NOx)" and "par-
ticulate matter (PM)" contained in the exhaust gas must be greatly reduced to meet exhaust gas regulations, and tech-
nology is being actively developed for the sake of improved fuel economy and reduced exhaust gases.

(1) Demands on Diesel Vehicles

• Reduce exhaust gases (NOx, PM, carbon monoxide (CO), hydrocarbon (HC) and smoke).
• Improve fuel economy.
• Reduce noise.
• Improve power output and driving performance.

om
l.c
(2) Transition of Exhaust Gas Regulations (Example of Large Vehicle Diesel Regulations)

ua
• The EURO IV regulations take effect in Europe from 2005, and the 2004 MY regulations take effect in North America
an
from 2004. Furthermore, the EURO V regulations will take effect in Europe from 2008, and the 2007 MY regulations
irm

will take effect in North America from 2007. Through these measures, PM and NOx emissions are being reduced in
pa

stages.
re
e-
ic
rv

PM NOx
se

g/kWh g/kWh
Europe Europe
EURO EURO EURO EURO EURO EURO

North America
1998 MY 2004 MY 2007 MY
3.5

2.7
North
America 2.0
0.13
0.11 1998 MY 2004 MY 2007 MY

0.03 0.27
0.013
2004 2005 2007 2008 2004 2005 2007 2008
Q000989E