Scribd
Upload
145 views

Chapter5 - General Inspection

Beechcraft Baron Service Manual component.

Uploaded by

Elmer Villegas
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
145 views

Chapter5 - General Inspection

Beechcraft Baron Service Manual component.

Uploaded by

Elmer Villegas
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Maintenance Manual (Rev G12)

05-00-00-601 (Rev Oct 1/10)

TIME LIMITS/MAINTENANCE CHECKS


GENERAL
INSPECTION/CHECK
1. TIME LIMITS/MAINTENANCE CHECKS - GENERAL - INSPECTION/CHECK
Warning: When an airplane has experienced abnormal landing gear indications of any type, as a safety precaution, place the
airplane on jacks before performing any inspection or maintenance (Ref. 07-10-00, 201, JACKING). Make sure all three
landing gears are down and locked before removing the airplane from jacks.
When doing any of the Inspections/Checks contained in this maintenance schedule, obey all of the warnings and
cautions stated in the Maintenance Manual associated with the system or component under inspection/check.

A. Scheduled Maintenance Checks


The owner or operator is responsible for maintaining the airplane in an airworthy condition, including compliance with all applicable
Airworthiness Directives as specified in Part 39 of Title 14 of the Code of Federal Regulations (14 CFR). It is further the
responsibility of the owner or operator to ensure that the airplane is inspected in conformity with the requirements covered in 14
CFR Parts 43.15 and 91.409 (f) (3). These 14 CFR Parts cover the requirements concerning the Inspection Guide. This inspection
guide is not intended to be all-inclusive, for no such guide can replace the good judgement of a certified airframe and power plant
mechanic in the performance of his duties. As the one primarily responsible for the airworthiness of the airplane, the owner or
operator should select only qualified personnel to maintain the airplane.

B. Special Conditions Cautionary Notice


The time periods for the inspections noted in this schedule are based on normal usage under average environmental conditions.
Airplanes operated in humid tropics, or in cold, damp climates, etc., may need more frequent inspections for wear, corrosion,
lubrication, and/or lack of maintenance. Under these adverse conditions, perform periodic inspections in compliance with this guide
at more frequent intervals until the owner or operator can set his own inspection periods based on the contingencies of field
experience.
Note: The required periods do not constitute a guarantee the item will reach the period without malfunction as the
aforementioned factors cannot be controlled by the manufacturer.
This inspection program in accordance with 14 CFR Parts 43 and 91 consist of, but is not limited to, inspection items
listed in the Inspection Guide, any applicable Airworthiness Directives issued against the airframe or any equipment
installed therein and conformity to Type Certificate Data Sheet as applicable.
Material contained in this guide, including the inspection intervals, may be changed at any time by the
owner/operator, with prior notification and approval of the local FAA General Aviation District Office, when warranted
by service experience or engineering recommendations. Information contained herein is applicable to all Baron 55
and 58 series airplanes except where differences are indicated by serial effectivity.
While the inspection guide may be used as an outline, detailed information of the many systems and components in the airplane
will be found in the various chapters of this manual and the pertinent supplier publications. It is also recommended that reference
be made to the applicable Maintenance Handbooks, Service Instructions, Hawker Beechcraft Corporation Service Bulletins,
applicable FAA Regulations and Publications, suppliers bulletins and specifications for torque values, clearances, settings,
tolerances, and other requirements. In the final analysis, it is the responsibility of the owner/operator to ensure the airframe and
power plant mechanic inspecting the airplane has access to previously noted documents as well as to this inspection guide.
Note: Any time an airplane is repainted or touched up, inspect all placards and decals to assure they are not covered with
paint, are easily readable, and are securely attached. Replace any placards that have been inadvertently defaced or
removed.
In addition to the inspections prescribed by this schedule, the altimeter system and all ATC transponders MUST be
tested and inspected at 24-month intervals in compliance with the requirements specified in 14 CFR Parts 91.411,
and 91.413.
A complete inspection of the airplane must be accomplished within each 12-month period for compliance with the Title 14 Code of
Federal Regulations. The time periods for inspections stated in this inspection guide should NEVER be exceeded by more than 10
hours, and then only if the additional time is required to reach a place where the inspection can be satisfactorily accomplished.
However, the additional time used must be deducted from the next inspection time. If 10 hours were used to reach the inspection
facility, the next inspection would be due in 90 hours for the next 100-hour inspection with no extension allowed.
Note: An airplane must receive a complete 100-hour, annual, or complete continuing care inspection every 12 months
regardless of the hours flown. The inspections completed during a 12-month period can be deleted from the items to
be inspected. Rubber goods such as fuel lines are recommended to be changed at five year periods regardless of

Copyright © Textron Aviation Inc. Page 1 of 2


Retain printed data for historical reference only. For future maintenance, use only current data. Print Date: Thu Oct 25 01:10:32 CDT 2018
Maintenance Manual (Rev G12)
05-00-00-601 (Rev Oct 1/10)

airplane time.
Additional publications are listed on the web at http://pubs.hawkerbeechcraft.com. For information on these
publications contact the Technical Manual Distribution Center (TMDC) at 1-800-796-2665, fax (316) 676-4824 or E-mail
[email protected].
All electrical systems operational inspections are to be made using an external power source capable of delivering
and maintaining 28.25 volts ± 0.25 volts.
The Hawker Beechcraft Corporation issues service information for the benefit of owners and operators in the form of two classes
of Service Bulletins. MANDATORY (Red Border) Service Bulletins are changes, inspections or modifications that could affect
safety. The factory considers compliance with these Service Bulletins mandatory. OPTIONAL (No Border) Service Bulletins cover
changes, modifications, improvements or inspections which may benefit the owner. Due to the wide range of information covered
by the OPTIONAL Service Bulletin, each owner or operator is responsible for conducting a thorough review of each OPTIONAL
Service Bulletin to determine if compliance is required based on the applicability of the OPTIONAL Service Bulletin to their
particular set of operating conditions. It is the responsibility of the owner or operator to ensure that all Hawker Beechcraft
Corporation Service Bulletins which are pertinent to their particular operation are complied with.

C. Maintenance Inspection Program


The Hawker Beechcraft factory approved inspection program is for all airplane models covered by this manual. Any variation to the
inspection program must be approved in writing by the FAA Flight Standards District Office (FSDO), or Airworthiness Authority.
The Maintenance Inspection Program meets the requirement of both 14 CFR 91 and 14 CFR 135.

D. Airworthiness Limitation Statement


There are no additional Airworthiness Limitations as defined in 14 CFR 23, Appendix G, G23.4 for the airplane models covered by
this manual. The Airworthiness Limitations section is FAA approved and specifies maintenance required under Section 43.16 and
Section 91.403 of the Federal Aviation Regulations unless an alternative program has been FAA Approved.

FAA Approved by: _________________________

Randolph C. Shields

ODA Lead administrator

Hawker Beechcraft Corporation

ODA-230339-CE

Copyright © Textron Aviation Inc. Page 2 of 2


Retain printed data for historical reference only. For future maintenance, use only current data. Print Date: Thu Oct 25 01:10:32 CDT 2018

You might also like