Scribd
Upload
360 views

AATCC Test Method 42 (Water Resistance: Impact Penetration Test)

This document summarizes AATCC Test Method 42, which tests the water resistance of fabrics using impact penetration. It sprays water onto fabric samples backed by weighed blotting paper. The increase in blotter mass is measured to determine water penetration resistance. The test can be used to predict rain resistance of garments. It describes the test equipment, sample preparation, testing procedure, evaluation method, and analysis of precision between two tester types. Variances between testers were low, showing the method produces consistent results.

Uploaded by

ADITI AWASTHI
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
360 views

AATCC Test Method 42 (Water Resistance: Impact Penetration Test)

This document summarizes AATCC Test Method 42, which tests the water resistance of fabrics using impact penetration. It sprays water onto fabric samples backed by weighed blotting paper. The increase in blotter mass is measured to determine water penetration resistance. The test can be used to predict rain resistance of garments. It describes the test equipment, sample preparation, testing procedure, evaluation method, and analysis of precision between two tester types. Variances between testers were low, showing the method produces consistent results.

Uploaded by

ADITI AWASTHI
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

AATCC Test Method 42

(Water Resistance: Impact Penetration Test)

Developed in 1945 by AATCC Committee RA63; revised 1952, 2000; reaffirmed


1957, 1961, 1964, 1967, 1971, 1977, 1980, 1989; editorially revised and reaffirmed
1985, 1994; editorially revised 1986, 1987.

Purpose and Scope:

 This test method is applicable to any textile fabric, which may or may not have been given a
water-resistance or water repellent finish.
 It measures the resistance of fabrics to the penetration of water by impact, and thus can be
used to predict the probable resistance of fabrics to rain penetration. It is especially suitable
for measuring the penetration resistance of garment fabrics.
 The results obtained with this test method depend on the water repellency of the fibres, yarns,
construction and finish of the fabric.

Principle:

A volume of water is allowed to spray against a taut surface of a test specimen backed by a
weighed blotter. The blotter is then reweighed to determine water penetration and the specimen
is classified accordingly.

Apparatus and Materials:

 Impact penetration testers


 Type I tester (see Figs. 1,3) or
 Type II tester (see Figs. 2,3)
 White AATCC textile blotting paper
 Water: distilled, deionized or reverse osmosis
 Balance accurate to 0.1g

Test Specimens:

 A minimum of three specimens are taken each 178 × 330 mm.


 The specimens and the blotting paper should be conditioned in an atmosphere of 65 ± 2% RH
and 21 ± 10c for at least 4 hr before testing.
Figure:1,2&3:Impact penetration type I and type II tester and its structural details

Procedure:

 One end of the specimen is clamped under the 152 mm spring clamp at the top of the inclined
stand. Another 152 ± 10 mm clamp, of 0.4536 kg total mass, is clamped at the free end of the
test specimen (see fig.3).
 A standard blotter paper 152 × 230 mm is weighed to the nearest 0.1g and inserted beneath
the test specimen (see fig.3).
 A 500 ± 10 mL volume of distilled, deionized water at 27 ± 1 0c is poured into a funnel of the
tester and allowed to spray onto the test specimen (see fig.3).
 The water should be poured into the funnel without imparting any swirling motion of the
water in the funnel.
 Upon completion of the spraying period, the test specimen is carefully lifted, the blotter
beneath removed, and then quickly reweighed to the nearest 0.1g.
Evaluation:

 The increase in mass of the blotter in grams is calculated and the average result of the three
test specimens is reported. Individual determinations or average values of over 5.0 g may be
simply reported as +5.0 g or > 5.0 g.
 Each fabric was evaluated 15 times and averages calculated for each group of three.

Precision and Bias:

 Three sets of fabrics were analyzed using both pieces of equipment.


a. Variances ranged in value from 0.1- 0.4 with an average value of 0.23 for the type I
tester, as determined by analysis of variance. Critical differences, based on these
values and a 95% probability level, may be applied to determine significance.
b. Variances ranged in value from 0.0-0.1 with an average value of 0.01 for the type II
tester, as determined by analysis of variance. Critical differences based on these
values and a 95% probability level may be applied to determine significance.
 The values derived by this procedure can be defined only in terms of test method. There is no
independent referee method for determining the true value. This test method has no known
bias.

Submitted By:
Monalisa Pradhan

Roll no: 1501106446

You might also like