Scribd
Upload
109 views5 pages

Service Manual 3Y11 Chassis: Design and Specifications Are Subject To Change Without Prior Notice. (Only Referrence)

This document provides service manual instructions for adjusting various components of a 3Y11 chassis, including: 1) Adjusting the B+ voltage to 110V +/- 0.5V by adjusting VR601. 2) Instructions for entering factory mode to adjust components like AGC voltage and screen voltage. 3) Additional adjustments for focus, white balance, sub-bright, vertical size and pincushion, horizontal center, Secam color decoder alignment, and pure flat tube alignment using patterns and voltage measurements.

Uploaded by

olegvs
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
109 views5 pages

Service Manual 3Y11 Chassis: Design and Specifications Are Subject To Change Without Prior Notice. (Only Referrence)

This document provides service manual instructions for adjusting various components of a 3Y11 chassis, including: 1) Adjusting the B+ voltage to 110V +/- 0.5V by adjusting VR601. 2) Instructions for entering factory mode to adjust components like AGC voltage and screen voltage. 3) Additional adjustments for focus, white balance, sub-bright, vertical size and pincushion, horizontal center, Secam color decoder alignment, and pure flat tube alignment using patterns and voltage measurements.

Uploaded by

olegvs
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

SERVICE MANUAL

3Y11 CHASSIS

Design and specifications are subject to change without prior notice.


( ONLY REFERRENCE)

_____
ENGINEER BY: _____
CHECKED BY: PPROVED BY: _____
Service Adjustments
MAIN CHASSIS ADJUSTMENT
B+ Adjustment (VR601)
(1) Disconnect horizontal load.Connect a light bulb(100W) AC250V across C321).
(2) Connect 220V AC 50/60Hz to CN601 and switch on power switch.
(3) Test the voltage with digital meter between C321 two terminals.
(4) Adjust VR601 to obtain +110V+/-0.5V.

FACTORY MODE ADJUSTMENT


(1) Press MENU key twin, till the PICTURE MENU appears, then press Q.VIEW key. MUTE key to turn on
CPU. TV SET will go to factory mode. Press TIMER key TO go to the next Factory menu. Go to MENU3
status by this means.
(2) Press MENU key to exit factory mode.

AGC Adjustment
(1) Receive 60dB +/-2dB therefore signal. Connect Digital voltmeter positive terminal to AGC terminal of
Tuner and negative terminal to GND.
(2) Go to MENU3 status accorging to FACTORY MODE ADJUSTMENT.
(2) Select RF.AGC by pressing CH+ or PROG+ keys. Adjust VOL+ and VOL- keys to obtain 4V Digital vol-
Tage meter reading.
(3) Press MENU key to exit factory mode.

COMPLETE SET GENERAL ADJUSTMENT


FOCUS Adjustment
(1) Receive monoscope pattern.
(2) Set TV to work in dynamic status.
(3) Adjust the focus knob of FBT to get the clearest picture.

Screen Voltag Adjustment


(1) Go to factory mode MENU2 status according to AGC adjustment (2).
(2) Select V-KILL by prssing CH+ or PROG+ and CH- or PROG- KEYS.
(3) Press VOL+ key all the time, adjust the screen of FBT to get a horizontal faintness beam line. Then
Loose VOL+

White Balance Adjustment(Applied when servicing)


(1) Set the TV set to AV mode. Receive black white pattern(color temperature test pattern).
(2) Put the test probe 1 of CRT color analyzer (CA-100) on the low bright area and the test probe 2 on the high
bright area. Adjust bright and contrast to get 5nit of low bright area and 80nit of high bright area.
(3) Go to factory mode MENU2 according to AGC adjustment (2). Obtain low bright area to X=281 and Y=311
by adjusting R.bias and B.bias. Obtain both area to X=? and Y=? by adjusting the two status repeatedly.
Note: the values of X & Y may be changed by the favour 0f customers.

-15-
Service Adjustments
Sub-bright Adjustment
(1) Receive GREY SCALE signal.
(2) Set TV normal mode.
(3) Go to factory mode ,adjust sub-bright option to make the picture same as below.

Totally dark Can be seen the brightness

Ver tical size and pincushion adjustment


(1) Receive monoscope pattern. Set TV standard status. Adjust V.size to obtain picture vertical redisplay ratio
more than 90% in factory mode MENU1.
(2) Receive cross hatch pattern. Set TV standard status. Adjust V.LINE and V.SC to obtain picture vertical pin
cushion a good status in factory mode MENU1.
(3) Receive cross hatch pattern. Set Tv standard status. In factory mode MENU1 adjust V.POSITION to obtain
picture vertical center of CRT screen.

Horizontal Center adjustment


Receive PHILIPS pattern. Set TV standard status. Adjust H.PHASE to obtain horizontal center at the
center of of CRT screen.

Secam color decoder alignment


Receive the GREY SCALE/COLOR BAR signal. Enter into the factory mode. Adjust the valuse of secam
R-Y DC and Secam B-Y DC to make the gray scale to the normal color.

Pure flat tube alignment


Horizontal size and pincushion distortion must be adjusted in pure flat tube as following:
1. Receive mono scope pattern;Adjust VR902 untill redisplay ratio is correct.
2.Receive cross hatch pattern signal;Adjust Vr901 untill the erect klines of the CRT two sides are most
straight.

-16-
Chassis Block Diagram

-4-

You might also like