Scribd
Upload
35 views

UMG 508 - Multifunctional Power Analyser: Smart Energy & Power Quality Solutions

medidores

Uploaded by

Tavo Cox
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
35 views

UMG 508 - Multifunctional Power Analyser: Smart Energy & Power Quality Solutions

medidores

Uploaded by

Tavo Cox
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 34

Smart Energy &

Power Quality Solutions

UMG 508 – Multifunctional Power Analyser

with Ethernet and BACnet


UMG 508

UMG 508 – Multifunctional Power Analyser


with Ethernet and BACnet

The Power Analyser UMG 508 is an all-rounder for the gle-phase loads. The UMG 508 has per each current input
front door panel mounting. The device is equipped with a separate energy counter. The very large data memory
a colourful graphic display with intuitive user interface. of 256 MB permits the logging of all readings for months
The extensive measuring functions, such as monitoring even without intermediate reading.
of short term interruptions, inrush currents, transients,
harmonics up to the 40th order …) are unique in this price Areas of application
range.
t.POJUPSJOHPGBXJEFSBOHFPGFMFDUSJDBMBOEFOFSHZQBSBNFUFST

Extensive communication options, such as RS485 (Mod- t$POUJOVPVTNPOJUPSJOHPGUIFQPXFSRVBMJUZQBSBNFUFST


bus RTU, Profibus), Ethernet TCP / IP, BACnet, HTTP, FTP, t&UIFSOFU(BUFXBZGPSTVCPSEJOBUFNFBTVSFNFOUEFWJDFT
SNMP, SMTP, SNTP, or DNS allow a cost effective and t"OBMZTJTPGFMFDUSJDBMGBVMUTBOESPPUDBVTFBOBMZTJTJODBTFPG
rapid integration into existing communication structures. power failures
t$PTUDFOUSFNBOBHFNFOU
The measurement is made on 4 separate current inputs, t3FNPUFNPOJUPSJOHGPSSFBMFTUBUFNBOBHFNFOU
either for three phase systems with additional measure-
t6TBHFJOUFTUGBDJMJUJFT FHJOVOJWFSTJUJFT

ments in N or PE or the measurement of 4 individual sin-

Various versions with UL-approval available!

1
Main features and customer‘s benefit UMG 508

User-friendly graphical colour display with intuitive user interface


The high-resolution graphic display provides informative presentations
of line graphs, FFT harmonic as bar diagram, clear display of the kWh-
month values, alarm management/event viewer with dates and time
stamp, and many other features.

In addition to the information content the redesign of the UMG displays


focused very much on a user-friendly, self-explanatory and intuitive
operation of the UMG 508.

Modern communication architecture via Ethernet:


Cost-effective, fast and safe communication
In many cases the costs for installation and communication (e.g.
peripheral equipment for field buses) exceed those for the respective
power meters. Integration of the UMG 508 in an existing Ethernet
architecture means a fast, cost-efficient and reliable communication.
Additional interfaces enable the integration of the power analysers into
PLC or building automation systems. The use of open standards offers
great flexibility to the user.

Modbus Gateway:
Easy integration of devices without Ethernet interface
With the Modbus Gateway function of UMG 508 you can connect less
sophisticated Modbus RTU meters to Ethernet.The UMG 508 can be used
simultaneously as a gateway for sub-meters or prior instruments exis-
ting within the installation. Each instrument with a Modbus RTU interface
can be connected, if its data format and function codes correspond. Data
can be scaled and labelled.

Highspeed Modbus
The UMG 508 series can transfer data via RS485 interface with a speed
of up to 921.6 kB/s among each other device of this series.

Alarm management:
E-mail and homepage inform you, wherever you are...
Who would not agree? Just leaving the building the first call arrives
about certain problems in production, computer failure, energy
breakdown...

By using a webbrowser and IP address you have direct access to the


extremely powerful homepage of your UMG 508. You get detailed
information about the actual condition of your powergrid from the
homepage. Online data as well as historical data and graphs of events
are available. Via homepage you can directly calculate the costs of your
energy consumption and export it into a CSV-file or print it out.

Alternatively, an e-mail informs you, if overload occurs, short-term


interruptions disrupt your production process, harmonics reduce the life
expectancy of your technical equipment...

The applications are ceaseless.

2
Main features and customer‘s benefit UMG 508

Grids
t5/ 55HSJET
tBOEXJSFHSJET
Router SPS Software tVQUPTJOHMFQIBTFHSJET

8 Digital inputs
t1VMTFJOQVU
Interfaces t"MBSNJOQVUMPHJD
t&UIFSOFU t$POEJUJPONPOJUPSJOH
t1SPmCVT34 %46#
t)JHIMPXUBSJGGDIBOHFPWFS
t&NBYSFTFU

5 Digital outputs
t1VMTFPVUQVUL8ILWBSI
t4XJUDIJOHPVUQVU
t-JNJUPVUQVU
t&NBYPVUQVU
t-PHJDBMPVUQVU

Communication
t1SPUPDPMT1SPmCVT %17

t.PECVT 356 6%1 5$1 (BUFXBZ

t5$1*1
t#"$OFU
t)551GSFFMZQSPHSBNNBCMFIPNFQBHF Memory
t'51 mMFUSBOTGFS
t.#ZUF'MBTI
t4/.1 t.CZUF3".
t5'51 BVUPNBUJDDPOmHVSBUJPO

t/51 UJNFTZODISPOJTBUJPO

t4.51 FNBJMGVODUJPO

t%)$1 Power quality


t)BSNPOJDT TUUI
t4IPSUUFSNJOUFSSVQUJPOT
t5SBOTJFOUT çT

Accuracy t*OSVTIDVSSFOUT NT

t&OFSHZDMBTT "
t6OCBMBODF
t$VSSFOU t'VMMQFSJPE3.4SFDPSEJOH NJO

t7PMUBHF

Maximum demand control Programming language


tPVUQVUT

3
Power analyser UMG 508

Overview of product variants

Three / four phase universal measurement instrument; 50/ 60Hz; current transformer ../1/5A;
including GridVis programming and analysis software

Supply voltage Interfaces

application programmes
œPGOPNJOBMSBOHF

œPGOPNJOBMSBOHF

œPGOPNJOBMSBOHF

GSFFMZQSPHSBNNBCMF
Additional memory

Ethernet 100baseT
5 digital outputs
4 current inputs

8 digital inputs

Profibus DP V0
4 voltage and

256 MB Flash
95...240V AC,
7%$

48...180V DC
7"$

7%$
20...50V AC

RS 485*
Type Item number

t - - t t t t t t t t UMG 508 52.21.001

- t - t t t t t t t t UMG 508 52.21.002

- - t t t t t t t t t UMG 508 52.21.003

optionally available
Application programme Emax function Emax 52.21.080

BACnet communication BACnet 52.21.081


1
t$POUBJOFE/PUQPTTJCMF x DSUB-9 connector

Features

Memory 256 MB
Clock +/- 1 min per month
Integrated logic Programming language Jasic®
Operating hours counter yes
Weekly switching clock Jasic®

Periphery

Digital inputs as status or pulse input 8


Digital outputs as switching or pulse output 5
Password protection yes
Maximum demand control optional 64 channels yes
Software GridVis yes

Communication

Interfaces
RS 485*       LCQT yes
Profibus DP* Sub D9-pole up to 12 Mbps yes
Ethernet 10/100 Base- TX RJ-45 connector yes
Protocols
Modbus RTU yes
Profibus DP V0 yes
Modbus TCP yes
Modbus over TCP yes
Modbus-Gateway yes
HTTP homepage (configurable) yes
SMTP E-Mail yes
SNTP time synchronization yes
TFTP automatic configuration yes
FTP file transfer yes
SNMP yes
DHCP yes
TCP/IP yes
BACnet yes
*1 x DSUB-9 connector

4
Power analyser UMG 508

Technical data

QIBTFXJSFHSJE -/ --


  7"$ 
Nominal voltage
QIBTFXJSFHSJE --
7"$ 

Overvoltage class 600 V CAT III


Quadrants 4
Continuous Measurement yes
Sampling rate, 8 channels per channel 20 kHz
Weight 1 kg
Dimensions )NNY8NNY%NN
Mounting according to IEC EN60999-1/ DIN EN50022 Frontpanel mounting
Working temperature -10…55 °C

one wire, more wires, fine stranded wires 0.08 - 2.5 mm²
Connectable wires (U/I)
cable end sleeve 1.5 mm²

Protection class according to EN60529 IP 20

Measuring range

Voltage L-N, AC (without VT) 10…600 V rms


Voltage L-L, AC (without VT) 18…1000 V rms
$VSSFOU 5SBOTGPSNFSYVOEY"
0,005...6 A
Frequency of fundamental )[
Grids TN, TT, IT
Measurement in grids QI QI QI QIBOEVQUUPYQI

Measured values

Voltage - - - - -- -- -- BDDVSBDZœ


Current - - - - 4VN-- 4VN-- BDDVSBDZœ
K-factor - - - - yes
Rotating current components Positive/ Negative/ Zero Phase Sequence yes
Real, apparent, reactive power - - - - 4VN-- 4VN-- BDDVSBDZœ
Cos-phi / phase angle - - - - 4VN-- 4VN-- yes
Phase angle - - - - yes
- - - - 4VN-- 4VN--
Class 0.2 (…/5 A),
Real energy (kWh) - Consumed real energy (rate 1, rate 2)
Class 1 (…/1 A)
- Supplied real energy (rate 1, rate 2)
- - - - 4VN-- 4VN--
Reactive energy (Karh) - Inductive energy (rate 1, rate 2) Class 2
- Capacitive reactive energy
Apparent energy (kVAh) - - - - 4VN-- 4VN-- yes
Wave form voltage - - - - yes
Frequency of mains BDDVSBDZœ
Average values yes
Minimum and maximum values yes

Power quality

Current, voltage, real/reactive power (±)


Harmonics, 1st- 40th BDDVSBDZœ SEH SOH

- - - -


%JTUPSUJPOGBDUPS5)%6JO - - - - yes
%JTUPSUJPOGBDUPS5)%*JO - - - - yes
Unbalance yes
Positive/ Negative/ Zero Phase Sequence yes
Transients çT yes
Inrush-currents 10 ms yes
Malfunction writer yes
Short-term interruptions yes

5
UMG 508

Dimensional drawing Connection illustration

All measurement data in mm Ethernet connection

Side view View from below

Typical connection

6
Smart Energy &
Power Quality Solutions

✔ UMG 511 – Class A power quality analyser

according to IEC 61000-4-30


Power quality analyser UMG 511

UMG 511 – Class A power quality analyser


according to IEC 61000-4-30

The UMG 511 power quality analyser is particularly suitable Areas of application
for monitoring power quality according to standards such • Continuous monitoring of the power quality e.g. EN 50160
as the EN 50160. All power quality parameters are collected • Ethernet gateway for subordinate measurement points
and analysed e.g. flicker, short term interruptions with • Analysis of electrical faults for network problems
fault recorder function, transients, harmonics up to the • Monitoring of the internal distribution network according to
63rd and inrush currents etc. Extensive communication EN 61000-4-7, 4-15, 4-30
possibilities e.g. RS 485 Modbus, Profibus, Ethernet (TCP/ • Report generator for EN 50160 analysis
IP), BACnet, HTTP, FTP, SMTP, SNTP, DNS ... allow cost • Remote control
effective and rapid integration in existing communication
networks. Worldwide access to the embedded web
server can be gained through a web browser. The GridVis
software included in the content of delivery allows
extensive analysis just by the click of a button.

Various versions with UL-approval available!

1
Power quality analyser UMG 511

UMG 511

Added value with additional functions

Continuous monitoring of the power quality e.g. in


accordance with EN 50160. This serves for the purpose
of monitoring the supply power quality from the energy
supply side. The UMG 511 can also be used in applications
for failure analysis on the consumer side and is also used
as a preventative measure for network perturbations. A
rapid, cost-optimised and reliable communication system
can be developed through the Ethernet connection. The
instrument’s own homepage offers you the opportunity to
call up the data or configure the instrument directly using
the embedded web server.

The large number of digital and analogue inputs and


outputs offer a variety of communication systems
possibilities and allows connection to PLC systems and
independent control tasks. The GridVis analysis software
represents a fundamental part of the standard delivery. presentation of online data and the analysis of historical
The GridVis can be used to practically trigger analysis in data is also a benefit for finding the root cause of network
accordance with EN 50160 with the click of a button. The problems.

Main features

• Measurement of power quality according to • Continuous sampling of voltage and current inputs with 20kHz
DIN EN 61000-4-30, Class A • Recording of more than 2000 different measurement parameter
• Fourier analysis 1st to 63rd harmonic for U-LN, U-LL, I, P per measuring cycle (200ms)
(consumption/supply) and Q (ind./cap.) • Detection of transients >50µs and storage with up
• Measurement of harmonics and interharmonics (U-LN, U-LL, I) to 16.000 samples
according to DIN EN 61000-4-7 • Data logger / event memory (256MB Flashdisk)
• Analysis and evaluation according to DIN EN 50160 with the • 8 digital inputs and 5 digital outputs
contained programming and analysis software GridVis • Proibus DP/V0 alternatively RS 485 (Modbus RTU, Modbus-
• Flicker measurement according to DIN EN 61000-4-15 Master, optional BACnet)
• Measurement in TN and TT grids (600V CAT III) • Ethernet (Web-Server, E-Mail, optional BACnet)
• 4 voltage measuring inputs, 4 current measuring inputs • Programming of customer speciic applications in Jasic®

Applications
The power quality analyser which is equipped with serves the UMG 511 as a reference voltage for harmonic
4 current and voltage inputs collects and digitalises measurement, transient and event recording and for
the effective values (True RMS) from currents and the flicker meter. A nominal current can be set using
voltages in 40-70Hz (15-440Hz) networks. The integrated this for the measurement of electrical current events.
microprocessor calculates the electrical parameters The 4th current and voltage input represents a separate
from the sampling values. The relevant voltage can be measurement system. However, it is generally used for
defined as a phase-neutral or a phase-phase voltage measuring the current in the neutral or PE conductor or
for measurement in a three-phase system. The voltage used for measuring a voltage difference between N and PE.

2
Power quality analyser UMG 511

Display examples
The backlighted active matrix display (5,7“) of the UMG
511 enables the presentation of measurement values
in numerical form, as a bar chart or as a line graph.
Selected displays can automatically be displayed in
alternation (automatic display rotation). The instrument is
programmed using userfriendly clear text menus or the
GridVis software.

Example of a UMG 511 connection illustration Main measurement


The UMG 511 has 4 measurement channels for current
and voltage. The first three channels (main measurement)
are intended for use in a three-phase system.

Auxiliary measurement
The auxiliary measurement can be used for measurement
in a single-phase or symmetrical three-phase system.
Alternatively, the current input can be allocated to
the three-phase system of the main measurement for
measuring the neutral-conductor current. For example, the
voltage input could then be used for recording the voltage
between the neutral conductor and PE. The auxiliary
measurement provides all measurement parameters
like in the main measurement (current, voltage, power,
harmonics, transients, events and flicker).
Measurement in a four-phase network with main
measurement and auxiliary measurement

3
Scope of operation UMG 511

Networks
• IT, TN, TT networks
• 3 phase and 4 phase networks
Router PLC Software

8 digital inputs
• Pulse input
Interfaces • Logic input
• Ethernet • Status monitoring
• Proibus 485 • HT/LT switch over
• Emax (max. demand) resetting

5 digital outputs
• Pulse output kWh/kvarh
• Switch output
• Limit value output
• Emax output
• Logic output

(can be extended through external I/O


modules)

Communication
• Proibus (DP/V0)
• Modbus (RTU, UDP, TCP, gateway)
• TCP/IP
• BACnet
• HTTP (freely conigurable homepage) Memory
• FTP (ile transfer) • 256 MByte Flash
• TFTP (automatic coniguration) • 16 Mbyte RAM
• NTP (time synchronisation)
• SMTP (e-mail function)
• DHCP
• SNMP Power quality
• Harmonics up to 63rd
• Short-term interruptions
• Transient recorder (>50μs)
• Starting current (>10ms)
Measurement accuracy • Unbalance
• Class: 0.5S (…/5A) class • Half wave-effective value
• Current: 0.2% recordings (up to 4.5 min)
• Voltage: 0.2% • Flicker

Peak demand management programming language


• 64 stages for load shedding

4
Scope of operation UMG 511

Dimensional drawing Connection illustration

All measurement data in mm Ethernet connection

Side view View from below

Typical connection

5
Product variants and technical data UMG 511

Overview of product variants

Three/four phase power quality analysers; current transformer .../1/5a; including GridVis programming and analysis software

Supply voltage Interfaces


±10% of nominal range

±10% of nominal range

±10% of nominal range

Ethernet 100baseT
4 current inputs

Profibus DP V0
digital outputs
4 voltage and

256 MB Flash

digital inputs
95...240V AC,
80...340V DC

48...180V DC
44...130V AC

20...70V DC
20...50V AC

Memory

RS 485*
Type Item number

• - - • • 8 5 • • • UMG 511 52.19.001


- • - • • 8 5 • • • UMG 511 52.19.002

- - • • • 8 5 • • • UMG 511 52.19.003

Options (for all versions)


Emax function application program (peak demand management) Emax 52.19.080

BACnet communication BACnet 52.19.081


• = Contained - = Not possible *1 x DSUB-9 connector

General technical data


3-phase 4-wire grid (L-N, L-L) 417/720 V AC +10%
Nominal voltage
3-phase 3-wire grid (L-L) 600 V AC +10%
Overvoltage category 600 V CAT III
Quadrants 4
Continuous measurement yes
8 channel scanning rate Per channel 20 kHz
Weight 1 kg
Dimensions L=144mm x W=144mm x H=81 mm
Mounting According to IEC EN 60999-1/DIN EN 50022 Front panel mounting
Working temperature range -10…55 °C

Single wire, multi-wire, fine-wire 0.08 - 2.5 mm²


Connectable conductor (U/I)
pin cable lugs, ferrule 1.5 mm²

Protection class According to EN 60529 IP 50 front /IP 20 rear

6
Product variants and technical data UMG 511

Measurement range
L-N voltage, AC (without voltage transformer) Free voltage transformer settings 10…600 V AC rms
L-L voltage, AC (without voltage transformer) Free voltage transformer settings 18…1000 V AC rms
Current (transformer: x/1 and x/5A) 0.005..6 A
Frequency of mains (only for static frequence) 15...440 Hz
Networks TN, TT, IT
Measurement in single/multi-phase networks 1 ph, 2 ph, 3 ph, 4 ph

Periphery
Digital inputs Status, logic or pulse input 8
Digital outputs Switch logic output or pulse output 5
Password protection Multilevel yes
Peak load management Optional 64 channels yes
Software GridVis yes

Features
Memory 256 MB
Clock +/- 1 min per month
Integrated logic Programming language Jasic®
Operating hour meter yes
Weekly time switch Jasic®

Measurement values

Voltage L1, L2, L3, L4, L1-L2, L2-L3, L1-L3 Accuracy ±0.1 %

L1, L2, L3, L4 ±0.2 %


Current
Calculated sum current ±0.5%

K-factor L1, L2, L3, L4 yes


Three-phase current components Positive/ Negative/ Zero Phase Sequence yes
L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 Accuracy ±(0.4% + 0.10%)
40 ..70 Hz, cos-phi = 1 ±(0.4% + 0.0075%)
Effective, reactive and apparent power 40 ..70 Hz, cos-phi = > 0.8 ±(0.5% + 0.0075%)
40 ..70 Hz, cos-phi = > 0.5 ±(0.5% + 0.0075%)
15 ..440 Hz, cos-phi = > 0.5 ±(3.0% + 0.0075%)
Cos-phi, power factor L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 yes
Phase angle L1, L2, L3, L4 yes
L1, L2, L3, L4, Sum L1-L3, Sum L1-L4:
Class 0.2S (…/5A),
Effective energy (kWh) - Purchased effective energy (tariff 1, tariff 2)
Class 0.5S (…/1A)
- Supplied effective energy (tariff 1, tariff 2)
L1, L2, L3, L4, Sum L1-L3, Sum L1-L4:
Reactive energy (kvarh) - Inductive reactive power (tariff 1, tariff 2) Class 2
- Capacitive reactive power
Apparent energy (kVAh) L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 yes
Current/voltage wave form L1, L2, L3, L4 yes
Frequency of mains Accuracy ±0.1 %
Average value yes
Minimum and maximum values yes

7
Product variants and technical data UMG 511

Power quality

Harmonics order, 1st to 63rd Voltage L1, L2, L3, L4 Accuracy ± 5%


Harmonics, even/odd Accuracy ± 0.05

Interharmonics Current, voltage L1, L2, L3, L4 yes


Distortion factor THD- U in % L1, L2, L3, L4 yes
Distortion factor THD- I in % L1, L2, L3, L4 yes
Positive/negative/zero system yes
Actual flicker value L1, L2, L3, L4 yes
Short-term flicker value L1, L2, L3, L4 yes
Long-term flicker value L1, L2, L3, L4 yes
Transients 50 μs yes
Trigger events 10 ms yes
Inrush currents 10 ms yes
Event recorder yes,

Communication
RS 485 9.6, 19.2, 38.4, 57.6, 76.8, 115.2, 921.6 kbps yes
faces
Inter-

Profibus DP Plug, sub D 9-pole up to 12 Mbps yes


Ethernet 10/100 Base- TX RJ-45 sockets yes
Modbus RTU yes
Profibus DP V0 yes
Modbus TCP yes
Modbus over TCP yes
Modbus-Gateway yes
HTTP Homepage (configurable) yes
SMTP E-Mail yes
SNMP yes
SNTP Time synchronisation yes
TFTP Automatic configuration yes
Protocols

FTP File Transfer yes


DHCP yes
BACnet / IP yes, option

8
Smart Energy &
Power Quality Solutions

✔ UMG 604 – High performance power analysers


UMG 604

UMG 604 – High performance power analysers

High performance power analysers from the UMG Areas of application


604 product family are suitable for use at all network • For measuring, monitoring and checking electrical
levels. The high scanning rate enables a continuous parameters in energy distribution units
measurement by gathering more than 800 measurement • Consumption data collection and analysis (cost centre
parameters. Due to the very high performance level of data collection)
the digital signal processor, all important power quality • For monitoring the power quality (harmonics, short
parameters are recorded e.g. short-term interruptions term interruptions, transients, initial current…)
with fault recorder function, transients, harmonics up to • Measurement value generator for building
a 40th and starting current etc. Extensive communication management systems or PLC
options e.g. Ethernet (TCP/IP), BACnet, Modbus, Proibus, • Control tasks e.g. depending upon the achieved
RS232, RS485, HTTP, FTP, SMTP, SNTP, SNMP or DNS… measurement values or limit values
allow affordable and quick integration in the existing • Peak demand management (avoidance of costly and
communication architecture. Worldwide access to the dangerous peak loads)
embedded web server can be gained through a web • Ethernet gateway for subordinate measurement points
browser e.g. for energy consumption analysis. Programs • Remote monitoring
speciic to the user can be created with implemented
graphic programming. It is possible to run 7 user
programs simultaneously.
Various versions with UL-approval available!

2
Power analyser UMG 604

UMG 604 the extra compact power analyser


Added value through additional functions

Through the integration of various functions, the UMG


604 power analyser goes far beyond the limits of digital
multifunctional measuring equipment and, therefore,
offers the respective added value. The UMG 604 and the
use of state-of-the-art processors allow to offer a very fast
and extremely compact power analyser at an affordable
price.

The UMG 604 contains the following functions:


• Power analyser for electrical energy distribution
(over 800 parameters)
• Energy consumption and cost centre data collection
• Monitoring of power quality
• Peak demand management (optional)
• PLC function (up to 7 simultaneous freely
programmable programs, graphic programming)
• Transient recorder
• Event recorder
• Data logger Main features
• Modbus/Ethernet gateway
• Continuous measurement
• Collection of all relevant power quality parameters (harmonics,
short-term interruptions, unbalance ...)
• Ethernet and embedded web server
• Jasic® interpreter
• Up to 7 user deined programs
• GridVis software - full version included in the delivery

Applications
Major increases of energy costs make electrical energy a with 20 KHz per channel enables the collection of all
driving force in costing. With the UMG 604, you can make relevant electrical parameters (more than 800 values),
the irst step towards better cost eficiency. The precise minimum and maximum values, the basic power quality
collection of all energy data and electrical parameters values such as harmonics (up to the 40th, each phase
ensures the necessary amount of transparency in your with direction recognition) and short-term interruptions.
energy supplies. Concepts can be developed on the Even fast transients (> 50µs) can be safely identiied.
basis of the data e.g. electricity cost reductions and the Using modern communication processes, the collected
introduction of measures. These targeted improvements data is conducted to a central location, stored centrally
can also be monitored and recorded with the UMG 604. in a high-performance database and provided for further
processing in an open system. Simple integration in an
The UMG 604, equipped with a 500 MHz DSP (digital existing building management system control or PLC
signal processor), is a fast and high performing power environment expands the areas of application of the UMG
analyser. The continuous scanning of eight channels 604.

3
Power analyser UMG 604

DIN rail mounting (6 units): Ethernet/Modbus gateway: the affordable


reduction of installation costs connection of units without an Ethernet interface
Measurement equipment is usually installed in the low With the Modbus gateway function, simple Modbus RTU-
voltage main distribution as an integral measurement units can be connected to the Ethernet using the UMG 604.
instrument for the switchgear cabinet door. Installation For example, the UMG 604 can be used simultaneously as
and connection costs are signiicantly reduced by the a gateway for subordinate measurement points or older
installation of the UMG 604 on a 35mm DIN rail. This units which already exist in the installation. Each unit
means that the panel cut-out and wiring to the cabinet with a Modbus RTU interface, where the data format and
door is no longer necessary. In order to make use of the function codes match up, can be connected. Data can be
extensive functions of modern measuring equipment, marked and scaled.
the interconnection and central analysis of the data plays
an important role. This means that the on-site display Highspeed Modbus
generally serves the purpose of the initialisation and The devices of the UMG 604 series can transfer data
service only. between the units using the RS485 interface at a speed of
The decidedly compact UMG 604 is suitable for up to 921.5 kB/s.
installation in low voltage main distribution panels and
machines as well as in installation distribution boards The e-mail and homepage inform you
which is particularly of interest for applications in building wherever you are…
services engineering, information technology and data Who hasn’t experienced it before? You are hardly through
centres. the door and the telephone is already ringing. There are
problems in production, computers are crashing and the
energy supplies are lost.

You have direct access to the extremely high performance


homepage of the UMG 604 with a web browser and an
IP address. Extensive information is already available to
you on the homepage. Online data are available together
with historical data and graphs recording events. The
homepage can be used to directly convert the rates into
costs and be exported as a csv ile or printed. As an
alternative, you can let yourself be informed by e-mail
anywhere in the world if your energy supply becomes
overloaded, if short-term interruptions to the voltage
supplies bring your production processes to a standstill
or unauthorized harmonics reduce the lifespan of
equipment. The application possibilities are endless.

Modern communication processes through the


Ethernet: affordable, rapid and safe communication
The costs for installation and communication (e.g.
periphery for ield buses) often surpass the costs of the
equipment.

By connecting the equipment to an existing Ethernet


system, a fast, optimally priced and reliable communi-
cation system can be developed. Additional interfaces
allow the integration of power analysers in PLC systems
or in central building management systems. The use of
clear standards offers the user a high amount of lexibility.

4
Power analyser UMG 604

Residual current measurement (RCM)

Functionality
All lines on the output to be monitored are fed through
the current transformer, with the exception of the PE line.
If the system is operating correctly, the sum of all currents
is equal to zero so that no voltage is induced in the current
transformer. In the event that a fault current lows via
ground or other channel, the current difference induces
a current in the current transformer which is captured by
the residual current measurement device.

UMG 604D
The UMG 604D monitors the residual currents of pure
alternating currents in TN and IT networks in electrical
systems, displays the current value and issues a warning
if the limit values are exceeded.
Differently coloured terminals
for residual current measure-
In addition to the operating currents L1-L3, the fourth
ment (current input 14)
measurement input for residual current measurement is
coloured differently (light grey) and suitable for currents up
to 30 mA. The current transformer with a transformation
ratio of 600/1A and suficiently-dimensioned internal
dimensions (20x30, 50x80 or 80x120mm) can be found in
section 6, page 166.
Extended main features of UMG 604D

• Measures the increase in residual current


• Allows for maintenance scheduling
• Warns if the limit values are exceeded
• Detects slowly developing fault currents
• Detects weaknesses in the electrical system
• Residual current monitoring device
(RCM – Residual current monitoring)

Illustration: Connection for measurement channels and differential


current transformer of series KBU (split core).

5
Power analyser UMG 604

GridVis EMS-/PQM system software

Online monitoring with the software


GridVis
The software GridVis, which comes along
with the content of delivery, allows an
individual collection, reading out of historic
data and visualisation of online data. The
received data of multiple measuring points
are collected, saved, processed, visualised
and provided for further use. All measured
values are available in the mode of online
measurement either as a line graph or bar
graph.

The topology gives a quick overview of


the energy distributions and the possibility
to locate power failures by comparing
measuring points and checking the deined
Illustration: topological view
tolerances at a glance.

Depositing some graphical iles (common


formats such as .jpg) with circuit diagrams,
low processes or building plans and
binding of the corresponding instruments
by drag and drop to their real position, you
can establish customer speciic solutions
quickly and simply.

Main features

• Parameterisation and programming of UMG


measurement equipment
• Visualisation of the measurement values with
topological view
• Automatic download of the measurement data
• Data storage
• Online analysis tools
• Analysis tools for historic data

Illustration: Report presentation for voltage quality (simple report)

6
Power analyser UMG 604

Visualisation, topological view


GridVis allows an individually adaptable visualisation
of online data. The topological view provides a rapid
overview of energy distribution with the possibility of
localising power faults by comparing the individual
measurement points and by offering the possibility to
check the deined tolerances at a glance.

Customer speciic solutions can be quickly and simply


implemented through uploading of graphic documents
(standard formats such as JPG) with circuit diagrams,
production lines or construction plans and incorporating
the respective measurement units by drag and drop into
their actual locations. Limit value excesses (e.g. THD-U is
too high) and the status of inputs and outputs can also be
displayed.

Online values and analysis of historic data


With the graphic line writer function, GridVis enables rapid
online presentation of the selected measurement values.
In this function, the graph is continuously expanded with
new measurement values. For example, load proiles can
be presented through the analysis of historic data in order
to produce exact consumption analysis for optimised
electricity supply contracts. Fault analysis through the
comparison of various parameters can also be achieved
with a few mouse clicks.

Graphic programming
The graphic programming option for user programs is
completely new in the ield of digital power analysers.
Programs speciic to the application can be created with
this method such as the free programming of inputs and
outputs, monitoring of processes or the issue of reports
when deined limit values are achieved. In addition to the
operator-friendly graphic programming, the user is also
free to program the Jasic® code directly.

programming language

The Jasic® programming language offers brand new


opportunities. The user is no longer tied to the functions
which are ixed integrations in the unit; the unit can be
expanded to include more functions. Up to seven of
these freely deinable user programs can be processed
simultaneously in the unit.

7
Power analyser UMG 604

Networks
• IT, TN, TT - networks
• 3 phase and 4 phase networks
Router SPS Software • Up to 4 single phase networks

2 digital inputs
• Pulse input
Interfaces • Logic input
• Ethernet • Status monitoring
• RS 232 • HT/LT conversion
• RS 485 • Emax (max. demand) resetting

2 digital outputs
• Pulse output kWh/kvarh
• Switch output
• Limit value output
• Emax output
• Logic output

(can be extended through external I/O


modules – see chapter 6)

Profibus connection

Communication Temperature measurement input


• Proibus (DP/V0) • PT 100, PT 1000, KTY 83, KTY 84
• Modbus (RTU, UDP, TCP, gateway)
• TCP/IP
• BACnet
• HTTP (freely conigurable homepage) Memory
• FTP (ile transfer) • 128 MB Flash
• SNMP • 16 MB RAM
• TFTP (automatic coniguration)
• NTP (time synchronisation)
• SMTP (e-mail function)
Power quality
• DHCP
• Harmonics up to 40th
• Short-term interruptions
• Transient recorder (>50µs)
Measurement accuracy • Starting current (>10ms)
• Class: 0.5S (…/5A) class • Unbalance
• Current: 0.2% • Full wave-effective value
• Voltage: 0.2% recordings (up to 4.5 min)

Peak demand management (optional) programming language


• 64 stages for load shedding

8
Product variants and technical data UMG 604

Overview of product variants

Three/four phase power analysers; 50/60Hz; current transformer .../1/5a; including GridVis programming and analysis software

Supply voltage Interfaces

7 freely programmable
±10% of nominal range

±10% of nominal range

±10% of nominal range

application programs
1 temperature input

Ethernet 100baseT
2 digital outputs
4 current inputs

2 digital inputs

Proibus DP V0
135...340 V DC

4 voltage and

128 MB Flash
95...240 V AC,

50...155V DC
50...110V AC

20...77V DC
20...55V AC

Memory

RS 232

RS 485
Type Item number

• - - • • • • • • • • - • UMG 604 E 52.16.002

- • - • • • • • • • • - • UMG 604 E 52.16.012

- - • • • • • • • • • - • UMG 604 E 52.16.022

• - - • • • • • • • • • • UMG 604 EP 52.16.001

- - • • • • • • • • • • • UMG 604 EP 52.16.021

• - - • • • • • • • • • • UMG 604 DE 52.16.041

Options (for all versions)

Emax function application program (peak demand management) Emax 52.16.080

BACnet communication BACnet 52.16.081

Accessories for UMG 604D

Differential current transformer, transmission ratio of 600/1A, interior dimensions: 20mm x 30mm KBU 23D 15.03.400

Differential current transformer, transmission ratio of 600/1A, interior dimensions: 50mm x 80mm KBU 58D 15.03.401

Differential current transformer, transmission ratio of 600/1A, interior dimensions: 80mm x 120mm KBU 812D 15.03.402
- = Not possible • = Contained Not suitable for use in residential areas.

General technical data


Nominal voltage 3-phase 4-wire grid (L-N, L-L) 277/480 V AC
3-phase 3-wire grid (L-L) 480 V AC
Overvoltage category 300V CAT III
Quadrants 4
Continuous measurement yes
8 channel scanning rate Per channel 20 kHz
Weight 350g
Dimensions L=107.5mm* W=90mm* H=62 mm
Mounting According to IEC EN60999-1/DIN EN50022 35mm DIN rail
Working temperature range -10…55 °C
Single wire, multi-wire, ine-wire 0.08 - 2.5 mm²,
Connectable conductor (U/I))
pin cable lugs, ferrule 1.5 mm²
Protection class According to EN 60529 IP 20

Measurement range
L-N voltage, AC
Free voltage transformer settings Networks to 480 V AC
(without voltage transformer)
Current (transformer: x/1 and x/5A) 0.001..7.5 A
Frequency of mains 45 ..65 Hz
Networks IT, TN, TT
Measurement in single/multi-phase networks 1 ph, 2 ph, 3 ph, 4 ph and up to 4 x 1 ph

Periphery
Digital inputs Status, logic or pulse input 2
Digital outputs Switch logic output or pulse output 2
Temperature measurement input PT100, PT1000, KTY83, KTY84 1
Password protection Multilevel yes
Peak demand management Optional 64 channels yes
Software GridVis yes

9
Product variants and technical data UMG 604

Measurement values

Voltage L1, L2, L3, L4, L1-L2, L2-L3, L1-L3 Accuracy ±0.2%
Current L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 Accuracy ±0.2%
K-factor L1, L2, L3, L4 yes
Three-phase current components Positive/negative/zero phase sequence yes
Effective, reactive and apparent power L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 Accuracy ±0.4%
Cos-phi, power factor L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 yes
Phase angle L1, L2, L3, L4 yes
L1, L2, L3, L4, Sum L1-L3, Sum L1-L4:
Class 0.5S (…/5 A),
Effective energy (kWh) - Purchased effective energy (tariff 1, tariff 2)
Class 1 (…/1 A)
- Supplied effective energy (tariff 1, tariff 2)

L1, L2, L3, L4, Sum L1-L3, Sum L1-L4:


Reactive energy (kvarh) - Induktive Blindarbeit (Tarif 1, Tarif 2) Class 2
- Kapazitive Blindarbeit
Apparent energy (kVAh) L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 yes
Current/voltage wave form L1, L2, L3, L4 yes
Frequency of mains Accuracy ±0.01
Temperature measurement Accuracy ±1.5%
Average value yes
Minimum and maximum values yes

Features
Memory 128 MB
Clock +/- 1 min per month
Integrated logic Programming language Jasic®
Operating hour meter yes
Weekly time switch Jasic®

Power quality
Current, voltage reactive/effective power (±)
Harmonics, 1-40 harmonic Accuracy ±0,5%
L1, L2, L3, L4
Distortion factor THD- U in % L1, L2, L3, L4 yes
Distortion factor THD- I in % L1, L2, L3, L4 yes
Unbalance yes
Positive/negative/zero system yes
Transients 50 μs yes
Start-up processes 10 ms yes
Fault recorder function yes
Short-term interruptions yes

Communication
RS 232 9.6, 19.2, 38.4, 115.2 kbps yes
RS 485 9.6, 19.2, 38.4, 57.6, 76.8, 115.2, 921.6 kbps yes
Interfaces

Proibus DP Plug, sub D 9-pole up to 12Mbps Yes, EP version


Ethernet 10/100 Base- TX RRJ-45 sockets yes
Modbus RTU yes
Proibus DP V0 Yes, EP version
Modbus TCP yes
Modbus over TCP yes
Modbus-Gateway yes
HTTP Homepage (conigurable) yes
SMTP E-mail yes
SNMP yes
SNTP Time synchronisation yes
TFTP Automatic coniguration yes
FTP File transfer yes
Protocols

DHCP yes
BACnet / IP yes, option

10
UMG 604

Connection illustration

Dimensional drawing
90 mm
90 mm

107.5 mm 50 mm
76 mm
82 mm

Illustration: front view Illustration: side view

11
Smart Energy &
Power Quality Solutions

✔ UMG 605 – power quality analyser

(EN 50160, IEEE 519, ITIC)


UMG 605

UMG 605 – power quality analyser


(EN 50160, IEEE 519, ITIC)

The UMG 605 power quality analyser is particularly Areas of application


suitable for monitoring power quality according to • Continuous monitoring of the power quality e.g.
standards such as the EN 50160. All power quality EN 50160
parameters are collected and analysed e.g. flicker, short- • Ethernet gateway for subordinate measurement points
term interruptions with fault recorder function, transients, • Analysis of electrical faults for network problems
harmonics up to 63rd and inrush currents etc. Extensive • Monitoring of the internal distribution network
communication possibilities e.g. RS 485 Modbus, Profibus, according to EN 61000-4-7, 4-15, 4-30
Ethernet (TCP/IP), BACnet, HTTP, FTP, SMTP, SNTP, SNMP, • Report generator for EN 50160 analysis
DNS .... allow cost effective and rapid integration in • Control tasks, e.g. depending on achieved measured
existing communication networks. Worldwide access to values or limits
the embedded web server can be gained through a web • Transducer for building automation or PLC systems
browser. The GridVis software included in the content of
delivery allows extensive analysis just with the click of a
button.

Various versions with UL-approval available!

1
Power quality analyser UMG 605

UMG 605 the extra compact power quality analyser


Added value through additional functions

Thanks to state-of-the-art digital signal processor, it is


possible to offer the power quality analyser UMG 605 at
a very reasonable price. The high sampling rate enables
a continuous measurement of more than 2000 measured
values per measurement cycle (200ms). The UMG 605
power quality analyser serves the purpose of continuous
monitoring of the power quality e.g. in accordance with
EN 50160. This serves the purpose of monitoring the
supply power quality from the energy supply side. The
UMG 605 can also be used in applications for failure
analysis on the consumer side and is also used as a
preventative measure for network perturbations.

Main Features
• Measurement of power quality according to DIN EN 61000-4-30 • Recording of more than 2000 different measurement parameters
• Measurement method class A per measuring cycle (200ms)
• Fourier analysis 1st to 63rd harmonics for U-LN, U-LL, I, P • Detection of transients >50µs and storage with up to 16.000
(consumption/supply) and Q (ind./cap.) samples
• Measurement of harmonics and interharmonics (U-LN, U-LL, I) • Data logger/event memory (128MB Flashdisk)
• Analysis and evaluation according to DIN EN 50160 with the • 2 digital inputs and 2 digital outputs
contained programming and analysis software GridVis • Proibus DP/V0 alternatively RS 485 (Modbus RTU, Modbus-
• Flicker measurement according to DIN EN 61000-4-15 Master, optional BACnet)
• Measurement in IT and TT grids (300V CAT III) • Ethernet (Web-Server, E-Mail, optional BACnet)
• 4 voltage measuring inputs, 4 current measuring inputs • Programming of customer speciic applications in Jasic®
• Continuous sampling of the voltage and current measuring
inputs with 20kHz

Applications
The power quality analyser which is equipped with serves the UMG 605 as a reference voltage for harmonic
4 current and voltage inputs collects and digitalises measurement, transient and event recording and for
the effective values (True RMS) from currents and the flicker meter. A nominal current can be set using
voltages in 40-70Hz (15-440Hz) networks. The integrated this for the measurement of electrical current events.
microprocessor calculates the electrical parameters The 4th current and voltage input represents a separate
from the sampling values. The relevant voltage can be measurement system. However, it is generally used for
defined as a phase-neutral or a phase-phase voltage measuring the current in the neutral or PE conductor or
for measurement in a three-phase system. The voltage used for measuring a voltage difference between N and PE.

2
Power quality analyser UMG 605

Networks
• IT, TN, TT networks
• 3 phase and 4 phase networks
Router SPS Software • Up to 4 single phase networks

2 digital inputs
• Pulse input
Interfaces • Logic input
• Ethernet • Status monitoring
• RS232 • HT/LT switch over
• RS485 • Emax (max. demand) resetting

2 digital outputs
• Pulse output kWh/kvarh
• Switch output
• Limit value output
• Emax output
• Logic output

(can be extended through external


I/O modules)

Profibus connection

Communication Temperature measurement input


• Proibus (DP/V0) • PT 100, PT 1000, KTY 83, KTY 84
• Modbus (RTU, UDP, TCP, Gateway)
• TCP/IP
• BACnet (optional) Memory
• HTTP (freely conigurable homepage) • 128 MB Flash
• FTP (ile transfer) • 16 MB RAM
• SNMP
• TFTP (automatic coniguration)
• NTP (time synchronisation)
• SMTP (e-mail function) Power quality
• DHCP • Harmonics up to 63rd
• SNMP • Short-term interruptions
• Transient recorder (>50μs)
• Starting current (>10ms)
Measurement accuracy • Unbalance
• Class: 0.5S (…/5A) class • Half wave-effective value
• Current: 0.2% recordings (up to 4.5 min)
• Voltage: 0.2% • Flicker

Peak demand management programming language


• 64 stages for load shedding

3
Scope of operation and types of variants UMG 605

Overview
Three/four phase power quality analysers; current transformer .../1/5a; including GridVis programming and analysis software

Supply voltage Interfaces


±10% nominal range

±10% nominal range

±10% nominal range

1 temperature input

Ethernet 100baseT
4 current inputs

Profibus DP V0
digital outputs
135...340 V DC

4 voltage and
95...240 V AC,

128 MB Flash

digital inputs
50...155V DC
50...110V AC

20...77V DC
20...55V AC

Memory

RS 232

RS 485
Type Item number

• - - • • 2 2 • • • • • UMG 605 52.16.027

- • - • • 2 2 • • • • • UMG 605 52.16.028

- - • • • 2 2 • • • • • UMG 605 52.16.029

Options (for all versions)

Emax function application program (peak demand management) Emax 52.16.084

BACnet communication BACnet 52.16.083

- = not possible • = contained

General technical data


Nominal voltage 3-phase 4-wire grid (L-N, L-L) 277/480 V AC
3-phase 3-wire grid (L-L) 480 V AC
Overvoltage category 300V CAT III
Quadrants 4
Continuous measurement yes
8 channel scanning rate Per channel 20 kHz
Weight 350g
Dimensions L=107.5mm* W=90mm* H=76/82mm
Mounting According to IEC EN 60999-1/DIN EN 50022 35mm DIN rail
Working temperature range -10…55 °C
Single wire, multi-wire, fine-wire, 0.08 - 2.5 mm²,
Connectable conductor (U/I)
pin cable lugs, ferrule 1.5 mm²
Protection class According to EN 60529 IP 20

Measurement range
L-N voltage, AC (without voltage transformer) Free voltage transformer settings Networks to 480 V AC
Current (transformer: x/1 and x/5A) 0.005...6 A
Frequency of mains (only for static frequence) 15...440 Hz
Networks IT, TN, TT
Measurement in single/multi-phase networks 1 ph, 2 ph, 3 ph, 4 ph and up to 4 x 1 ph

Periphery
Digital inputs Status, logic or pulse input 2
Digital outputs Switch logic output or pulse output 2
Temperature measurement input PT100, PT1000, KTY83, KTY84 1
Password protection Multilevel yes
Demand management Optional 64 channels yes
Software GridVis yes

Features
Memory 128 MB
Clock +/- 1 min per month
Integrated logic Programming language Jasic®
Operating hour meter yes
Weekly time switch Programming language Jasic®

4
Scope of operation and types of variants UMG 605

Measurement values
Voltage L1, L2, L3, L4, L1-L2, L2-L3, L1-L3 Accuracy ±0.2%
Current L1, L2, L3, L4 / Calculated sum current ±0.2% / ±0.6%
K-factor L1, L2, L3, L4 yes
Three-phase current components Positive/ Negative/ Zero Phase Sequence yes
Cos-phi, power factor L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 yes
Phase angle L1, L2, L3, L4 yes
L1, L2, L3, L4, Sum L1-L3, Sum L1-L4:
Class 0.5S (…/5 A),
Effective energy (kWh) - Purchased effective energy (tariff 1, tariff 2)
Class 1 (…/1 A)
- Supplied effective energy (tariff 1, tariff 2)
L1, L2, L3, L4, Sum L1-L3, Sum L1-L4:
Reactive energy (kvarh) - Inductive reactive power (tariff 1, tariff 2) Class 2
- Capacitive reactive power
Apparent energy (kVAh) L1, L2, L3, L4, Sum L1-L3, Sum L1-L4 yes
Current/voltage wave form L1, L2, L3, L4 yes
Frequency of mains Accuracy ±0.1%
Temperature measurement Accuracy±1.5%
Average value yes
Minimum and maximum values yes

Power quality
Harmonics order, 1.- 63.
Voltage L1, L2, L3, L4 Accuracy ± 0.5%
Harmonics, even/odd

Interharmonics Current, voltage L1, L2, L3, L4 yes


Distortion factor THD- U in % L1, L2, L3, L4 yes
Distortion factor THD- I in % L1, L2, L3, L4 yes
Positive/negative/zero system yes
Actual flicker value L1, L2, L3, L4 yes
Short term flicker value L1, L2, L3, L4 yes
Long term flicker value L1, L2, L3, L4 yes
Transients 50 μs yes
Trigger events 10 ms yes
Inrush currents 10 ms yes
Event recorder yes

Communication
Interfaces
RS 232 9.6, 19.2, 38.4, 115.2 kbps yes
RS 485 9.6, 19.2, 38.4, 57.6, 76.8, 115.2, 921.6 kbps yes
Profibus DP Plug, sub D 9-pole up to 12Mbps yes
Ethernet 10/100 Base- TX RJ-45 sockets yes
Protocols
Modbus RTU yes
Profibus DP V0 yes
Modbus TCP yes
Modbus over TCP yes
Modbus-Gateway yes
HTTP Homepage (configurable) yes
SMTP E-Mail yes
SNMP yes
SNTP Time synchronisation yes
TFTP Automatic configuration yes
FTP File Transfer yes
DHCP yes
BACnet / IP yes, Option

5
UMG 605

Connection illustration

Dimensional drawing
90 mm
90 mm

107.5 mm 50 mm
76 mm
82 mm

Illustration: front view Illustration: side view

You might also like