Scribd
Upload
167 views

Design PDF Bommakur

The document provides the design and analysis of a roof truss for the Bommakur Pump House in Telangana, India. It includes the scope, material properties, applicable codes and standards, design philosophy, and wind load calculations. The roof truss is designed for dead loads, live loads, and wind loads using the applicable load combinations from the Indian codes. The wind loads are calculated based on the basic wind speed of the area and modeling of the structure. The roof truss structure is analyzed in STAAD Pro software.

Uploaded by

Rama Krishna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
167 views

Design PDF Bommakur

The document provides the design and analysis of a roof truss for the Bommakur Pump House in Telangana, India. It includes the scope, material properties, applicable codes and standards, design philosophy, and wind load calculations. The roof truss is designed for dead loads, live loads, and wind loads using the applicable load combinations from the Indian codes. The wind loads are calculated based on the basic wind speed of the area and modeling of the structure. The roof truss structure is analyzed in STAAD Pro software.

Uploaded by

Rama Krishna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 113

IRRIGATION & COMMAND AREA DEVELOPMENT

DEPARTMENT
GOVERNMENT OF TELANGANA

GLIS PHASE-III (PACKAGE – IV)

DESIGN AND DRAWINGS OF ROOF TRUSS FOR


BOMMAKUR PUMP HOUSE

Agency
NCC- MEIL-ZVS-SIGMA (JV)
Hyderabad.
Report on Roof Truss for Bommakur Pump House 
 

I. Introduction:    J.Chokka  Rao  Devadula  Lift  irrigation  Scheme‐phase‐III  Package‐IV:              


Investigation,  Design  &  Execution  of  Tunnel    of  minimum  internal  diameter  4m  ‘D’ 
shaped/modified horse shoe with carrying  of 15.30 cumecs  water from Dharmasagar tank to 
R.S.Ghanpur  tank  and  construction  of  head  regulator  at  the  entrance  portal  of  tunnel  and 
construction of pumping station at R.S.Ghanpur and Investigation, design and Laying  pipeline of 
single row with 1.9m dia from Dharmasagar to Gandiramaram, 2.6m dia. From Gandiramaram 
to  Bommakuru,2.5m  dia.  From  Bommakuru  to  Tapaspally,  from  oftake  (valve)  to 
Kanneboinagudem with 0.9m dia. pipeline, from offtake (valve) to Veldanda with 1.30m dia.Pipe 
line  and  0.5m  dia.Pipe  line  from  Tapaspally  to  Jeellagudem  and  formation  of  tank  near 
Jeellagudem and distributary system for 2000 acres and 1.2m dia. Pipeline from R.S.Ghanpur to 
Aswaraopally  and  construction  of  pumping  stations  at  Dharmasagar,  Gandiramaram, 
Bommakuru,  Tapaspally  and  R.S  Ghanpur  including  execution  of  civil,  electro‐mechanical  and 
hydro‐mechanical,  instrumentation,  auxiliary,  miscellaneous  equipment  and  SCADA 
communication system at all pumping stations in Warangal district of Andhra Pradesh‐India. 
 
II. Scope of Work:  This document covers the Analysis and Design of Roof Truss for the Bommakur 
Pump House. 
 
III. Units of Measurement: Units of measurements used in analysis shall be of SI Units 

IV. Material Properties:

Material  Property  Value  Units 


Structural Steel  Density  78.5  kN/cum 
  Yield Strength  250  N/sq.mm 
Modulus of Elasticity  200000  N/sq.mm 
V. Codes and Standards :

IS Code No  Description 
IS: 875‐1997  Part I – Dead Loads. 
Part II – Imposed Loads 
Part III – Wind Loads 
Part V – Special Loads and Load Combinations 
IS: 800‐1984  Code of practice for steel structures. 
SP‐6  Steel Sections. 
SP‐38  Handbook  of  typified  design  for  structures  with  steel  roof 
trusses. 

VI. Design Philosophy :

1. Design Conditions:  Roof Truss is designed for all dead, live and wind loads with 

applicable load combinations. Design of Steel roof truss structures of pumping station shall 
be as per the latest Indian Codes.  
 
2. Modeling: The roof for pump house is modeled in STAAD Pro as space frame.  Designs of 
steel members are checked in the STAAD Pro. The Base plates and Anchor Bolts is designed 
by using excel for maximum Loads. 
 
3. Loads considered for Design and Analysis:   The following loads are taken for analysis and 
design     
 
• Dead Load  
• Live Load 
• Wind Load 
 
 
4. Load Calculations: Dead loads will include the weight of all structural and architectural 

components including permanently applied external loads. Self‐weight of materials will be 
calculated on the basis of unit weights given in IS: 875 (Part I).
Roof structure is designed for a live load of 75 kg/ sq m. 
Wind Load Calculations ‐ Bommakur Roof Truss

BASIC WIND SPEED  =  44 m/sec FROM APPENDIX ‐A ‐ AS PER IS :875 (PART 3) ‐ 1987


for Zone II
CALCULATION OF DESIGN WIND SPEED (VZ)

K1 = 1.07 FROM TABLE ‐1 ‐ AS PER IS :875 (PART 3) ‐ 1987 (Imporatant Buliding )

FROM TABLE ‐2 ‐ AS PER IS :875 (PART 3) ‐ 1987 FOR TERRAIN CATEGORY 2 ‐ 
K2 = 1.05
CLASS A

K3 =  1.00 FROM CLAUSE ‐ 5.3.3.1 AS PER IS:875(PART 3) ‐1987

FROM CLAUSE ‐ 5.3 AS PER 
WIND SPEED = (VZ) =  49.4 m/sec *VZ = Vb*K1*K2*K
IS:875(PART 3) ‐1987

2 FROM CLAUSE ‐ 5.4 AS PER 
WIND PRESSURE = (PZ) =  1.466 kN/m *PZ = 0.6*VZ 2
IS:875(PART 3) ‐1987

HEIGHT OF BUILDING = h =  15.00 m *h = SUMP BOTTOM LEVEL ‐ TOP SLAB LEVEL

WIDTH OF BUILDING = w =  14.85 m

LENGTH OF BUILDING = l =  22.25 m

EACH BAY WIDTH  = 8.00 m

h/w =  1.01

l/w =  1.5

slope =1/7.5 = 0.133333 = 0.1326 Rad = 7.59 0

spacing of purlins 1.0
1) PITCHED ROOFS  

FROM TABLE ‐ 5 AS PER IS :875 (PART 3) ‐ 1987

EXTERNAL INTERNAL COMBINATIONS


WIND ANGLE WIND WARD(1) LEE WARD(2) EXHAUST(3) SUCTION(4) 1+3 1+4 2+3 2+4
0 ‐1.00 ‐0.60 ‐0.2 0.2 ‐1.2 ‐0.8 ‐0.8 ‐0.4
90 ‐0.85 ‐0.60 ‐0.2 0.2 ‐1.05 ‐0.65 ‐0.8 ‐0.4

2
DESIGN WIND PRESSURE = ‐1.759 kN/m WIND ANGLE = 0 , WIND WARD SIDE+EXHAUST WIND LOAD CASE‐1 ( Use in STAAD Pro.)
2
DESIGN WIND PRESSURE = ‐1.173 kN/m WIND ANGLE =0 LEEWARD SIDE +EXHAUST

2
DESIGN WIND PRESSURE = ‐1.173 kN/m WIND ANGLE = 0 , WIND WARD SIDE+SUCTION WIND LOAD CASE‐2
2
DESIGN WIND PRESSURE = ‐0.586 kN/m WIND ANGLE =0 LEEWARD SIDE +SUCTION

2
DESIGN WIND PRESSURE = ‐1.540 kN/m WIND ANGLE =90 , WIND WARD SIDE+EXHAUST WIND LOAD CASE‐3
2
DESIGN WIND PRESSURE = ‐1.173 kN/m WIND ANGLE =90 LEEWARD SIDE +EXHAUST

2
DESIGN WIND PRESSURE = ‐0.953 kN/m WIND ANGLE =90 , WIND WARD SIDE+SUCTION WIND LOAD CASE‐4
2
DESIGN WIND PRESSURE = ‐0.586 kN/m WIND ANGLE =90 LEEWARD SIDE +SUCTION
LOADS
DESIGN WIND LOAD = ‐1.759 kN/m WIND ANGLE = 0 , WIND WARD SIDE+EXHAUST WIND LOAD CASE‐1
DESIGN WIND LOAD = ‐1.173 kN/m WIND ANGLE =0 LEEWARD SIDE +EXHAUST

DESIGN WIND LOAD = ‐1.173 kN/m WIND ANGLE = 0 , WIND WARD SIDE+SUCTION WIND LOAD CASE‐2


DESIGN WIND LOAD = ‐0.586 kN/m WIND ANGLE =0 LEEWARD SIDE +SUCTION

DESIGN WIND LOAD = ‐1.540 kN/m WIND ANGLE =90 , WIND WARD SIDE+EXHAUST WIND LOAD CASE‐3 ( Use in STAAD Pro.)


DESIGN WIND LOAD = ‐1.173 kN/m WIND ANGLE =90 LEEWARD SIDE +EXHAUST

DESIGN WIND LOAD = ‐0.953 kN/m WIND ANGLE =90 , WIND WARD SIDE+SUCTION WIND LOAD CASE‐4


DESIGN WIND LOAD = ‐0.586 kN/m WIND ANGLE =90 LEEWARD SIDE +SUCTION
STAAD INPUT 

STAAD SPACE 

START JOB INFORMATION 

ENGINEER DATE 12‐May‐15 

JOB NAME ROOF TRUSS FOR PUMP HOUSE 

JOB CLIENT GLIS‐III,PKG‐IV‐BOMMAKUR 

END JOB INFORMATION 

INPUT WIDTH 79 

UNIT METER KN 

JOINT COORDINATES 

1 0.1 0 15.1; 4 7.525 1 15.1; 5 7.525 2 15.1; 6 0.1 1 15.1; 

7 1.09129 1.13173 15.1; 8 3.07386 1.3952 15.1; 9 2.08257 1.26346 15.1; 

10 4.06514 1.52693 15.1; 11 5.05643 1.65866 15.1; 12 6.04771 1.79039 15.1; 

13 7.039 1.92213 15.1; 14 1.09129 0.131732 15.1; 15 3.07386 0.395197 15.1; 

16 2.08257 0.263465 15.1; 17 4.06514 0.526929 15.1; 18 5.05643 0.658661 15.1; 

19 6.04771 0.790394 15.1; 20 7.039 0.922126 15.1; 21 14.95 0 15.1; 

22 14.95 1 15.1; 23 13.9587 1.13173 15.1; 24 11.9761 1.3952 15.1; 

25 12.9674 1.26346 15.1; 26 10.9849 1.52693 15.1; 27 9.9936 1.65866 15.1; 

28 9.00229 1.79039 15.1; 29 8.011 1.92213 15.1; 30 13.9587 0.131732 15.1; 

31 11.9761 0.395197 15.1; 32 12.9674 0.263465 15.1; 33 10.9849 0.526929 15.1; 

34 9.9936 0.658661 15.1; 35 9.00229 0.790394 15.1; 36 8.011 0.922126 15.1; 

37 0.1 0 22.25; 39 7.525 1 22.25; 40 7.525 2 22.25; 41 0.1 1 22.25; 

42 1.09129 1.13173 22.25; 43 3.07386 1.3952 22.25; 44 2.08257 1.26346 22.25; 

45 4.06514 1.52693 22.25; 46 5.05643 1.65866 22.25; 47 6.04771 1.79039 22.25; 

48 7.039 1.92213 22.25; 49 1.09129 0.131732 22.25; 50 3.07386 0.395197 22.25; 

51 2.08257 0.263465 22.25; 52 4.06514 0.526929 22.25; 
53 5.05643 0.658661 22.25; 54 6.04771 0.790394 22.25; 55 7.039 0.922126 22.25; 

56 14.95 0 22.25; 57 14.95 1 22.25; 58 13.9587 1.13173 22.25; 

59 11.9761 1.3952 22.25; 60 12.9674 1.26346 22.25; 61 10.9849 1.52693 22.25; 

62 9.9936 1.65866 22.25; 63 9.00229 1.79039 22.25; 64 8.011 1.92213 22.25; 

65 13.9587 0.131732 22.25; 66 11.9761 0.395197 22.25; 

67 12.9674 0.263465 22.25; 68 10.9849 0.526929 22.25; 69 9.9936 0.658661 22.25; 

70 9.00229 0.790394 22.25; 71 8.011 0.922126 22.25; 72 0.1 0 8; 74 7.525 1 8; 

75 1.09129 0.131732 8; 76 7.525 2 8; 77 0.1 1 8; 78 1.09129 1.13173 8; 

79 2.08257 1.26346 8; 80 3.07386 1.3952 8; 81 4.06514 1.52693 8; 

82 5.05643 1.65866 8; 83 6.04771 1.79039 8; 84 7.039 1.92213 8; 

85 2.08257 0.263465 8; 86 3.07386 0.395197 8; 87 4.06514 0.526929 8; 

88 5.05643 0.658661 8; 89 6.04771 0.790394 8; 90 7.039 0.922126 8; 

91 14.95 0 8; 92 13.9587 0.131732 8; 93 14.95 1 8; 94 13.9587 1.13173 8; 

95 12.9674 1.26346 8; 96 11.9761 1.3952 8; 97 10.9849 1.52693 8; 

98 9.9936 1.65866 8; 99 9.00229 1.79039 8; 100 8.011 1.92213 8; 

101 12.9674 0.263465 8; 102 11.9761 0.395197 8; 103 10.9849 0.526929 8; 

104 9.9936 0.658661 8; 105 9.00229 0.790394 8; 106 8.011 0.922126 8; 

107 0.1 1 18.675; 108 7.525 2 11.575; 109 0.1 1 11.575; 110 14.95 1 11.575; 

111 7.525 2 18.675; 112 14.95 1 18.675; 113 1.09129 1.13173 18.675; 

114 3.07386 1.3952 18.675; 115 2.08257 1.26346 18.675; 

116 4.06514 1.52693 18.675; 117 5.05643 1.65866 18.675; 

118 6.04771 1.79039 18.675; 119 7.039 1.92213 18.675; 

120 13.9587 1.13173 18.675; 121 11.9761 1.3952 18.675; 

122 12.9674 1.26346 18.675; 123 10.9849 1.52693 18.675; 

124 9.9936 1.65866 18.675; 125 9.00229 1.79039 18.675; 

126 8.011 1.92213 18.675; 127 1.09129 1.13173 11.575; 
128 3.07386 1.3952 11.575; 129 2.08257 1.26346 11.575; 

130 4.06514 1.52693 11.575; 131 5.05643 1.65866 11.575; 

132 6.04771 1.79039 11.575; 133 7.039 1.92213 11.575; 

134 13.9587 1.13173 11.575; 135 11.9761 1.3952 11.575; 

136 12.9674 1.26346 11.575; 137 10.9849 1.52693 11.575; 

138 9.9936 1.65866 11.575; 139 9.00229 1.79039 11.575; 

140 8.011 1.92213 11.575; 141 0.1 0 30.25; 142 7.525 2 26.255; 

143 0.1 1 26.255; 144 1.09129 1.13173 26.255; 145 3.07386 1.3952 26.255; 

146 2.08257 1.26346 26.255; 147 4.06514 1.52693 26.255; 

148 5.05643 1.65866 26.255; 149 6.04771 1.79039 26.255; 

150 7.039 1.92213 26.255; 151 14.95 0 30.25; 152 14.95 1 26.255; 

153 13.9587 1.13173 26.255; 154 11.9761 1.3952 26.255; 

155 12.9674 1.26346 26.255; 156 10.9849 1.52693 26.255; 

157 9.9936 1.65866 26.255; 158 9.00229 1.79039 26.255; 

159 8.011 1.92213 26.255; 160 1.09129 0.131732 30.25; 161 7.525 1 30.25; 

162 7.525 2 30.25; 163 0.1 1 30.25; 164 1.09129 1.13173 30.25; 

165 2.08257 1.26346 30.25; 166 3.07386 1.3952 30.25; 167 4.06514 1.52693 30.25; 

168 5.05643 1.65866 30.25; 169 6.04771 1.79039 30.25; 170 7.039 1.92213 30.25; 

171 2.08257 0.263465 30.25; 172 3.07386 0.395197 30.25; 

173 4.06514 0.526929 30.25; 174 5.05643 0.658661 30.25; 

175 6.04771 0.790394 30.25; 176 7.039 0.922126 30.25; 

177 13.9587 0.131732 30.25; 178 14.95 1 30.25; 179 13.9587 1.13173 30.25; 

180 12.9674 1.26346 30.25; 181 11.9761 1.3952 30.25; 182 10.9849 1.52693 30.25; 

183 9.9936 1.65866 30.25; 184 9.00229 1.79039 30.25; 185 8.011 1.92213 30.25; 

186 12.9674 0.263465 30.25; 187 11.9761 0.395197 30.25; 

188 10.9849 0.526929 30.25; 189 9.9936 0.658661 30.25; 
190 9.00229 0.790394 30.25; 191 8.011 0.922126 30.25; 194 0.595643 0.0658657 8; 

195 0.595643 0.0658657 30.25; 198 14.4544 0.065866 8; 

199 14.4544 0.065866 30.25; 204 0.1 0.674 8; 205 14.95 0.674 8; 

212 0.1 0.674 30.25; 213 14.95 0.674 30.25; 218 1.09129 0.670732 8; 

219 13.9587 0.670732 8; 220 1.09129 0.670732 30.25; 221 13.9587 0.670732 30.25; 

226 2.08257 0.667465 8; 227 12.9674 0.667465 8; 228 2.08257 0.667465 30.25; 

229 12.9674 0.667465 30.25; 234 3.07386 0.665197 8; 235 11.9761 0.665197 8; 

236 3.07386 0.665197 30.25; 237 11.9761 0.665197 30.25; 242 4.06514 0.658929 8; 

243 10.9849 0.658929 8; 244 4.06514 0.658929 30.25; 245 10.9849 0.658929 30.25; 

257 7.525 1.26346 8; 258 3.07386 1.26346 8; 259 4.06514 1.26346 8; 

260 5.05643 1.26346 8; 261 6.04771 1.26346 8; 262 7.039 1.26346 8; 

263 11.9761 1.26346 8; 264 10.9849 1.26346 8; 265 9.9936 1.26346 8; 

266 9.00229 1.26346 8; 267 8.011 1.26346 8; 279 7.525 1.26346 30.25; 

280 3.07386 1.26346 30.25; 281 4.06514 1.26346 30.25; 

282 5.05643 1.26346 30.25; 283 6.04771 1.26346 30.25; 284 7.039 1.26346 30.25; 

285 11.9761 1.26346 30.25; 286 10.9849 1.26346 30.25; 287 9.9936 1.26346 30.25; 

288 9.00229 1.26346 30.25; 289 8.011 1.26346 30.25; 300 7.039 1.79039 8; 

301 8.011 1.79039 8; 302 7.039 1.79039 30.25; 303 8.011 1.79039 30.25; 

305 7.525 1.79039 8; 307 7.525 1.79039 30.25; 308 6.54335 1.79039 30.25; 

309 8.50664 1.26346 30.25; 310 6.54335 1.26346 30.25; 

311 8.50664 1.79039 30.25; 312 7.52501 0.658661 30.25; 

313 7.52502 0.0658659 30.25; 314 8.51001 0.658661 30.25; 

315 8.51002 0.0658659 30.25; 316 6.54002 0.658661 30.25; 

317 6.54002 0.0658658 30.25; 318 9.49795 1.26346 30.25; 

319 5.55207 1.26346 30.25; 320 9.50001 0.658661 30.25; 

321 9.50002 0.0658659 30.25; 322 5.55002 0.658661 30.25; 
323 5.55002 0.0658658 30.25; 324 4.56079 0.658795 30.25; 

325 10.4892 0.658795 30.25; 326 10.4892 1.26346 30.25; 

327 4.56079 1.26346 30.25; 328 4.56002 0.0658658 30.25; 

329 10.49 0.0658659 30.25; 330 3.5695 0.662063 30.25; 

331 11.4805 0.662063 30.25; 332 11.4805 1.26346 30.25; 

333 3.5695 1.26346 30.25; 334 3.57002 0.0658658 30.25; 

335 11.48 0.0658659 30.25; 336 6.54335 1.79039 8; 337 8.50664 1.26346 8; 

338 6.54335 1.26346 8; 339 8.50664 1.79039 8; 340 7.52502 0.0658659 8; 

341 7.52501 0.658661 8; 342 8.51002 0.0658659 8; 343 8.51001 0.658661 8; 

344 6.54002 0.0658658 8; 345 6.54002 0.658661 8; 346 9.49795 1.26346 8; 

347 5.55207 1.26346 8; 348 9.50002 0.0658659 8; 349 9.50001 0.658661 8; 

350 5.55002 0.0658658 8; 351 5.55002 0.658661 8; 352 3.5695 0.662063 8; 

353 4.56079 0.658795 8; 354 10.4892 0.658795 8; 355 11.4805 0.662063 8; 

356 11.4805 1.26346 8; 357 10.4892 1.26346 8; 358 4.56079 1.26346 8; 

359 3.5695 1.26346 8; 360 4.56002 0.0658658 8; 361 3.57002 0.0658658 8; 

362 10.49 0.0658659 8; 363 11.48 0.0658659 8; 

MEMBER INCIDENCES 

18 6 7; 19 7 9; 20 8 10; 21 9 8; 22 10 11; 23 11 12; 24 12 13; 25 13 5; 

26 14 16; 27 15 17; 28 16 15; 29 17 18; 30 18 19; 31 19 20; 32 20 4; 33 6 14; 

34 7 16; 35 9 15; 36 8 17; 37 10 18; 38 11 19; 39 12 20; 40 13 4; 51 22 23; 

52 23 25; 53 24 26; 54 25 24; 55 26 27; 56 27 28; 57 28 29; 58 29 5; 59 30 32; 

60 31 33; 61 32 31; 62 33 34; 63 34 35; 64 35 36; 65 36 4; 66 22 30; 67 23 32; 

68 25 31; 69 24 33; 70 26 34; 71 27 35; 72 28 36; 73 29 4; 84 5 111; 85 6 107; 

86 7 113; 87 8 114; 88 9 115; 89 10 116; 90 11 117; 91 12 118; 92 13 119; 

101 22 112; 102 23 120; 103 24 121; 104 25 122; 105 26 123; 106 27 124; 

107 28 125; 108 29 126; 122 41 42; 123 42 44; 124 43 45; 125 44 43; 126 45 46; 
127 46 47; 128 47 48; 129 48 40; 130 49 51; 131 50 52; 132 51 50; 133 52 53; 

134 53 54; 135 54 55; 136 55 39; 137 41 49; 138 42 51; 139 44 50; 140 43 52; 

141 45 53; 142 46 54; 143 47 55; 144 48 39; 155 57 58; 156 58 60; 157 59 61; 

158 60 59; 159 61 62; 160 62 63; 161 63 64; 162 64 40; 163 65 67; 164 66 68; 

165 67 66; 166 68 69; 167 69 70; 168 70 71; 169 71 39; 170 57 65; 171 58 67; 

172 60 66; 173 59 68; 174 61 69; 175 62 70; 176 63 71; 177 64 39; 187 72 194; 

188 74 257; 189 72 204; 190 77 78; 191 78 79; 192 80 81; 193 79 80; 194 81 82; 

195 82 83; 196 83 84; 197 84 76; 198 75 85; 199 86 87; 200 85 86; 201 87 88; 

202 88 89; 203 89 90; 204 90 74; 205 77 75; 206 78 85; 207 79 86; 208 80 87; 

209 81 88; 210 82 89; 211 83 90; 212 84 74; 213 78 218; 214 79 226; 215 80 258; 

216 81 259; 217 82 260; 218 83 261; 219 84 300; 221 91 198; 222 91 205; 

223 93 94; 224 94 95; 225 96 97; 226 95 96; 227 97 98; 228 98 99; 229 99 100; 

230 100 76; 231 92 101; 232 102 103; 233 101 102; 234 103 104; 235 104 105; 

236 105 106; 237 106 74; 238 93 92; 239 94 101; 240 95 102; 241 96 103; 

242 97 104; 243 98 105; 244 99 106; 245 100 74; 246 94 219; 247 95 227; 

248 96 263; 249 97 264; 250 98 265; 251 99 266; 252 100 301; 256 76 108; 

257 77 109; 258 78 127; 259 80 128; 260 79 129; 261 81 130; 262 82 131; 

263 83 132; 264 84 133; 273 93 110; 274 94 134; 275 96 135; 276 95 136; 

277 97 137; 278 98 138; 279 99 139; 280 100 140; 281 107 41; 282 108 5; 

283 109 6; 284 110 22; 285 109 127; 286 108 140; 287 111 40; 288 107 113; 

289 112 57; 290 111 126; 291 113 42; 292 114 43; 293 115 44; 294 116 45; 

295 117 46; 296 118 47; 297 119 48; 298 120 58; 299 121 59; 300 122 60; 

301 123 61; 302 124 62; 303 125 63; 304 126 64; 305 127 7; 306 128 8; 

307 129 9; 308 130 10; 309 131 11; 310 132 12; 311 133 13; 312 134 23; 

313 135 24; 314 136 25; 315 137 26; 316 138 27; 317 139 28; 318 140 29; 

319 133 108; 320 132 133; 321 131 132; 322 130 131; 323 128 130; 324 129 128; 
325 127 129; 326 134 110; 327 136 134; 328 135 136; 329 137 135; 330 138 137; 

331 139 138; 332 140 139; 333 119 111; 334 118 119; 335 117 118; 336 116 117; 

337 114 116; 338 115 114; 339 113 115; 340 120 112; 341 122 120; 342 121 122; 

343 123 121; 344 124 123; 345 125 124; 346 126 125; 347 6 127; 348 9 127; 

349 25 134; 350 22 134; 351 41 113; 352 44 113; 353 60 120; 354 57 120; 

355 39 4; 356 4 74; 357 127 79; 358 127 77; 359 134 93; 360 134 95; 361 113 9; 

362 113 6; 363 120 22; 364 120 25; 366 40 142; 367 41 143; 368 42 144; 

369 43 145; 370 44 146; 371 45 147; 372 46 148; 373 47 149; 374 48 150; 

376 57 152; 377 58 153; 378 59 154; 379 60 155; 380 61 156; 381 62 157; 

382 63 158; 383 64 159; 384 141 195; 385 161 279; 386 141 212; 387 163 164; 

388 164 165; 389 166 167; 390 165 166; 391 167 168; 392 168 169; 393 169 170; 

394 170 162; 395 160 171; 396 172 173; 397 171 172; 398 173 174; 399 174 175; 

400 175 176; 401 176 161; 402 163 160; 403 164 171; 404 165 172; 405 166 173; 

406 167 174; 407 168 175; 408 169 176; 409 170 161; 410 164 220; 411 165 228; 

412 166 280; 413 167 281; 414 168 282; 415 169 283; 416 170 302; 417 151 199; 

418 151 213; 419 178 179; 420 179 180; 421 181 182; 422 180 181; 423 182 183; 

424 183 184; 425 184 185; 426 185 162; 427 177 186; 428 187 188; 429 186 187; 

430 188 189; 431 189 190; 432 190 191; 433 191 161; 434 178 177; 435 179 186; 

436 180 187; 437 181 188; 438 182 189; 439 183 190; 440 184 191; 441 185 161; 

442 179 221; 443 180 229; 444 181 285; 445 182 286; 446 183 287; 447 184 288; 

448 185 303; 449 143 163; 450 142 162; 451 143 144; 452 152 178; 453 142 159; 

454 144 164; 455 145 166; 456 146 165; 457 147 167; 458 148 168; 459 149 169; 

460 150 170; 461 153 179; 462 154 181; 463 155 180; 464 156 182; 465 157 183; 

466 158 184; 467 159 185; 468 150 142; 469 149 150; 470 148 149; 471 147 148; 

472 145 147; 473 146 145; 474 144 146; 475 153 152; 476 155 153; 477 154 155; 

478 156 154; 479 157 156; 480 158 157; 481 159 158; 482 163 144; 483 165 144; 
484 180 153; 485 178 153; 486 161 39; 487 144 44; 488 144 41; 489 153 57; 

490 153 60; 493 194 75; 494 195 160; 497 198 92; 498 199 177; 501 195 334; 

502 194 361; 503 88 351; 506 174 322; 511 204 77; 512 205 93; 513 212 163; 

514 213 178; 519 218 75; 520 219 92; 521 220 160; 522 221 177; 527 226 85; 

528 227 101; 529 228 171; 530 229 186; 535 234 86; 536 235 102; 537 236 172; 

538 237 187; 543 242 87; 544 243 103; 545 244 173; 546 245 188; 581 204 218; 

582 218 226; 583 226 234; 584 234 352; 585 242 353; 586 104 354; 587 243 355; 

588 235 227; 589 227 219; 590 219 205; 591 79 258; 592 83 336; 593 257 305; 

594 258 234; 595 259 242; 596 260 88; 597 261 89; 598 262 90; 599 263 235; 

600 264 243; 601 265 104; 602 266 105; 603 267 106; 604 263 95; 605 264 356; 

606 265 357; 607 266 346; 608 267 337; 609 257 267; 610 262 257; 611 261 338; 

612 260 347; 613 259 358; 614 258 359; 649 212 220; 650 220 228; 651 228 236; 

652 236 330; 653 244 324; 654 189 325; 655 245 331; 656 237 229; 657 229 221; 

658 221 213; 659 165 280; 660 169 308; 661 279 307; 662 280 236; 663 281 244; 

664 282 174; 665 283 175; 666 284 176; 667 285 237; 668 286 245; 669 287 189; 

670 288 190; 671 289 191; 672 285 180; 673 286 332; 674 287 326; 675 288 318; 

676 289 309; 677 279 289; 678 284 279; 679 283 310; 680 282 319; 681 281 327; 

682 280 333; 717 300 262; 718 301 267; 719 302 284; 720 303 289; 725 301 339; 

726 305 301; 727 300 305; 728 305 76; 733 303 311; 734 307 303; 735 302 307; 

736 307 162; 737 7 14; 738 6 1; 740 9 16; 741 8 15; 742 10 17; 743 11 18; 

744 12 19; 745 13 20; 746 5 4; 747 29 36; 748 28 35; 749 27 34; 750 26 33; 

751 24 31; 752 25 32; 753 23 30; 754 22 21; 755 21 30; 756 1 14; 757 41 37; 

758 42 49; 759 44 51; 760 43 50; 761 45 52; 762 46 53; 763 47 54; 764 48 55; 

765 40 39; 766 64 71; 767 63 70; 768 62 69; 769 61 68; 770 59 66; 771 60 67; 

772 58 65; 773 57 56; 774 56 65; 775 37 49; 776 151 56; 777 56 21; 778 21 91; 

779 72 1; 780 1 37; 781 37 141; 782 308 302; 783 309 288; 784 310 284; 
785 311 184; 786 312 314; 787 313 315; 788 314 320; 789 315 321; 790 316 312; 

791 317 313; 792 308 310; 793 310 316; 794 316 317; 795 311 309; 796 309 314; 

797 314 315; 798 318 287; 799 319 283; 800 320 189; 801 321 329; 802 322 316; 

803 323 317; 804 318 320; 805 320 321; 806 319 322; 807 322 323; 808 324 174; 

809 325 245; 810 326 286; 811 327 282; 812 328 323; 813 329 335; 814 327 324; 

815 324 328; 816 326 325; 817 325 329; 818 330 244; 819 331 237; 820 332 285; 

821 333 281; 822 334 328; 823 335 199; 824 332 331; 825 331 335; 826 333 330; 

827 330 334; 828 336 300; 829 337 266; 830 338 262; 831 339 99; 832 340 342; 

833 341 343; 834 342 348; 835 343 349; 836 344 340; 837 345 341; 838 346 265; 

839 347 261; 840 348 362; 841 349 104; 842 350 344; 843 351 345; 844 352 242; 

845 353 88; 846 354 243; 847 355 235; 848 356 263; 849 357 264; 850 358 260; 

851 359 259; 852 360 350; 853 361 360; 854 362 363; 855 363 198; 856 359 352; 

857 352 361; 858 358 353; 859 353 360; 860 347 351; 861 351 350; 862 338 345; 

863 345 344; 864 337 343; 865 343 342; 866 346 349; 867 349 348; 868 357 354; 

869 354 362; 870 356 355; 871 355 363; 

DEFINE MATERIAL START 

ISOTROPIC STEEL 

E 2.05e+008 

POISSON 0.3 

DENSITY 76.8195 

ALPHA 1.2e‐005 

DAMP 0.03 

ISOTROPIC CONCRETE 

E 2.17185e+007 

POISSON 0.17 

DENSITY 23.5616 
ALPHA 1e‐005 

DAMP 0.05 

END DEFINE MATERIAL 

MEMBER PROPERTY INDIAN 

84 TO 92 101 TO 108 256 TO 264 273 TO 284 287 289 291 TO 318 776 TO 780 ‐ 

781 TABLE ST ISMC175 

221 417 493 494 581 TO 592 604 TO 614 649 TO 660 672 TO 682 725 TO 727 733 ‐ 

734 TO 735 782 TO 785 798 799 808 TO 811 818 TO 821 828 TO 831 838 839 844 ‐ 

845 TO 851 TABLE ST ISMC100 

188 189 213 TO 219 222 246 TO 252 385 386 410 TO 416 418 442 TO 448 ‐ 

511 TO 514 519 TO 522 527 TO 530 535 TO 538 543 TO 546 593 TO 603 ‐ 

661 TO 671 717 TO 720 728 736 TO 738 740 TO 754 757 TO 772 ‐ 

773 TABLE ST ISA50X50X6 

MEMBER PROPERTY INDIAN 

33 TO 40 66 TO 73 137 TO 144 170 TO 177 205 TO 212 238 TO 245 402 TO 409 434 ‐ 

435 TO 441 TABLE ST ISA75X75X6 

366 TO 374 376 TO 383 449 450 452 454 TO 467 TABLE ST ISMC200 

355 356 486 TABLE ST ISMC250 

18 TO 32 51 TO 65 122 TO 136 155 TO 169 187 190 TO 204 223 TO 237 384 387 ‐ 

388 TO 401 419 TO 433 497 498 755 756 774 775 TABLE ST ISMC125 

347 TO 354 357 TO 364 482 TO 485 487 TO 490 TABLE LD ISA75X75X6 SP 0.008 

MEMBER PROPERTY INDIAN 

285 286 288 290 319 TO 346 451 453 468 TO 481 PRIS YD 0.016 

501 TO 503 506 786 TO 791 800 TO 803 812 813 822 823 832 TO 837 840 TO 843 ‐ 

852 TO 855 TABLE ST ISMC125 

MEMBER PROPERTY INDIAN 
792 TO 797 804 TO 807 814 TO 817 824 TO 827 PRIS YD 0.016 

856 TO 871 PRIS YD 0.016 

UNIT KMS KN 

CONSTANTS 

MATERIAL STEEL ALL 

START GROUP DEFINITION 

MEMBER 

_PURLIN 84 TO 92 101 TO 108 256 TO 264 273 TO 284 287 289 291 TO 318 ‐ 

366 TO 374 376 TO 383 449 450 452 454 TO 467 

_PUR_TRUSS 18 TO 40 51 TO 73 84 TO 92 101 TO 108 361 TO 364 737 738 740 TO 756 

END GROUP DEFINITION 

UNIT METER KN 

SUPPORTS 

1 21 37 56 72 91 141 151 PINNED 

MEMBER RELEASE 

84 TO 92 101 TO 108 256 TO 264 273 TO 280 366 TO 374 376 TO 383 START MX MY MZ 

281 TO 284 287 289 291 TO 318 449 450 452 454 TO 467 END MX MY MZ 

MEMBER TRUSS  

33 TO 40 66 TO 73 137 TO 144 170 TO 177 188 189 205 TO 219 222 238 TO 252 ‐ 

385 386 402 TO 416 418 434 TO 448 511 TO 514 519 TO 522 527 TO 530 ‐ 

535 TO 538 543 TO 546 593 TO 603 661 TO 671 717 TO 720 728 736 

LOAD 1 LOADTYPE Dead  TITLE DL 

MEMBER LOAD 

84 TO 92 101 TO 108 256 TO 264 273 TO 284 287 289 291 TO 318 366 TO 374 376 ‐ 

377 TO 383 449 450 452 454 TO 467 UNI GY ‐0.2 

SELFWEIGHT Y ‐1 LIST 18 TO 40 51 TO 73 84 TO 92 101 TO 108 122 TO 144 155 ‐ 
156 TO 177 187 TO 219 221 TO 252 256 TO 264 273 TO 364 366 TO 374 376 TO 490 ‐ 

493 494 497 498 501 TO 503 506 511 TO 514 519 TO 522 527 TO 530 535 TO 538 ‐ 

543 TO 546 581 TO 614 649 TO 682 

MEMBER LOAD 

501 TO 503 506 591 592 604 TO 614 659 660 672 TO 682 725 TO 727 733 TO 735 ‐ 

782 TO 791 798 TO 803 810 TO 813 820 TO 823 828 TO 843 848 TO 854 ‐ 

855 UNI GY ‐0.1 

85 101 257 273 281 283 284 289 367 376 449 452 776 TO 781 UNI GY ‐0.04 

LOAD 2 LOADTYPE Live  TITLE LL 

MEMBER LOAD 

84 TO 92 101 TO 108 256 TO 264 273 TO 284 287 289 291 TO 318 366 TO 374 376 ‐ 

377 TO 383 449 450 452 454 TO 467 UNI GY ‐0.75 

LOAD 3 LOADTYPE Wind  TITLE WIND +X 

MEMBER LOAD 

84 TO 92 256 TO 264 281 TO 283 287 291 TO 297 305 TO 311 366 TO 374 449 450 ‐ 

454 TO 460 UNI GY 1.759 

101 TO 108 273 TO 280 284 289 298 TO 304 312 TO 318 376 TO 383 452 ‐ 

461 TO 467 UNI GY 1.173 

LOAD 4 LOADTYPE Wind  TITLE WIND +Z 

MEMBER LOAD 

84 TO 92 256 TO 264 281 TO 283 287 291 TO 297 305 TO 311 366 TO 374 449 450 ‐ 

454 TO 460 UNI GY 1.54 

101 TO 108 273 TO 280 284 289 298 TO 304 312 TO 318 376 TO 383 452 ‐ 

461 TO 467 UNI GY 1.173 

LOAD COMB 5 DL+LL 

1 1.0 2 1.0  
LOAD COMB 6 DL+WL +X 

1 1.0 3 1.0  

LOAD COMB 7 DL+WIND +Z 

1 1.0 4 1.0  

LOAD COMB 8 DL+LL+WIND +X 

1 1.0 2 1.0 3 1.0  

LOAD COMB 9 DL+LL+WL +Z 

1 1.0 2 1.0 4 1.0  

PERFORM ANALYSIS PRINT ALL 

PARAMETER 1 

CODE INDIAN 

PARAMETER 2 

CODE INDIAN 

CHECK CODE MEMB 18 TO 40 51 TO 73 84 TO 92 101 TO 108 122 TO 136 138 TO 144 ‐ 

155 TO 177 187 TO 219 221 TO 252 256 TO 264 273 TO 284 287 289 291 TO 318 ‐ 

347 TO 354 357 TO 364 366 TO 374 376 TO 450 452 454 TO 467 482 TO 485 487 ‐ 

488 TO 490 493 494 497 498 501 TO 503 506 511 TO 514 519 TO 522 527 TO 530 ‐ 

535 TO 538 543 TO 546 581 TO 614 649 TO 682 717 TO 720 725 TO 728 ‐ 

733 TO 738 740 TO 756 760 TO 770 774 TO 791 798 TO 803 808 TO 813 ‐ 

818 TO 823 828 TO 855 

PARAMETER 3 

CODE INDIAN 

STEEL MEMBER TAKE OFF LIST 18 TO 40 51 TO 73 84 TO 92 101 TO 108 122 TO 136 ‐ 

138 TO 144 155 TO 177 187 TO 219 221 TO 252 256 TO 264 273 TO 284 287 289 ‐ 

291 TO 318 347 TO 354 357 TO 364 366 TO 374 376 TO 450 452 454 TO 467 482 ‐ 

483 TO 485 487 TO 490 493 494 497 498 501 TO 503 506 511 TO 514 519 TO 522 ‐ 
527 TO 530 535 TO 538 543 TO 546 581 TO 614 649 TO 682 717 TO 720 ‐ 

725 TO 728 733 TO 738 740 TO 756 760 TO 770 774 TO 791 798 TO 803 ‐ 

808 TO 813 818 TO 823 828 TO 855 

FINISH 
Job No Sheet No Rev
1
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Job Information
Engineer Checked Approved

Name:
Date: 12-May-15

Structure Type SPACE FRAME

Number of Nodes 295 Highest Node 363


Number of Elements 641 Highest Beam 871

Number of Basic Load Cases 4


Number of Combination Load Cases 5

Included in this printout are data for:


Group G2: _PUR_TRUSS

Included in this printout are results for load cases:


Type L/C Name

Primary 1 DL
Primary 2 LL
Combination 5 DL+LL
Combination 6 DL+WL +X
Combination 7 DL+WIND +Z
Combination 8 DL+LL+WIND +X
Combination 9 DL+LL+WL +Z

Basic Load Cases


Number Name

1 DL
2 LL
3 WIND +X
4 WIND +Z

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 1 of 91
Job No Sheet No Rev
2
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Combination Load Cases


Comb. Combination L/C Name Primary Primary L/C Name Factor

5 DL+LL 1 DL 1.00
2 LL 1.00
6 DL+WL +X 1 DL 1.00
3 WIND +X 1.00
7 DL+WIND +Z 1 DL 1.00
4 WIND +Z 1.00
8 DL+LL+WIND +X 1 DL 1.00
2 LL 1.00
3 WIND +X 1.00
9 DL+LL+WL +Z 1 DL 1.00
2 LL 1.00
4 WIND +Z 1.00

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 2 of 91
Job No Sheet No Rev
3
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 18 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 18 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 29.8 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + L3 L5 FTZ = 165.0 |
| CMY = 0.60 | L5 FCY = 165.0 |
| CMZ = 0.46 + L3 L5 FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 9.2 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.8 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.260 3 |
| 48.27 T 0.0 0.6 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
18 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 3 of 91
Job No Sheet No Rev
4
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 19 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 19 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.8( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 60.2 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 400.0 +L5 FTZ = 165.0 |
| CMY = 0.60 | L5 L3 FCY = 165.0 |
| CMZ = 0.44 + L5 L3 FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 11.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.3 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.7 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.473 3 |
| 97.45 T 0.0 0.8 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
19 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 4 of 91
Job No Sheet No Rev
5
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 20 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 20 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + fa = 91.5 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.43 | L3 FCY = 165.0 |
| CMZ = 0.93 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 8.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.3 |
| DFF = 0.0 0.5 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.663 3 |
| 148.09 T 0.0 0.6 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
20 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 5 of 91
Job No Sheet No Rev
6
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 21 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 21 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.5( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 76.9 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.46 | L3 FCY = 165.0 |
| CMZ = 0.58 +L5 L6 FTY = 165.0 |
| FYLD = 249.9 | L8 L6 fbz = 7.9 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.3 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.9 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.563 3 |
| 124.54 T 0.0 0.5 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
21 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 6 of 91
Job No Sheet No Rev
7
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 22 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 22 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.7( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 98.3 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.59 | L3 L3 FCY = 165.0 |
| CMZ = 0.92 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 9.9 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.5 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.716 3 |
| 159.18 T 0.0 0.7 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
22 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 7 of 91
Job No Sheet No Rev
8
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 23 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 23 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + fa = 97.7 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.62 | L3 FCY = 165.0 |
| CMZ = 0.90 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 9.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.5 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.710 3 |
| 158.14 T 0.0 0.6 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
23 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 8 of 91
Job No Sheet No Rev
9
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 24 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 24 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 1.2( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 88.5 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.45 | L3 L3 FCY = 165.0 |
| CMZ = 0.76 + L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 17.8 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.3 |
| DFF = 0.0 0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.699 3 |
| 143.24 T 0.0 1.2 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
24 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 9 of 91
Job No Sheet No Rev
10
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 25 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 25 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 0.49 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 2.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 25.6 | L3 FA = 150.0 |
| KL/R-Z= 9.7 +L3 L3 fa = 81.6 |
| UNL = 492.2 | L3 L3 FCZ = 163.3 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.55 | FCY = 165.0 |
| CMZ = 0.40 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 29.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 1.0 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 10.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.729 3 |
| 132.17 T 0.0 -2.0 0.49 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
25 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 10 of 91
Job No Sheet No Rev
11
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 26 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 26 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.3( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 81.5 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.72 |L5 L3 FCY = 165.0 |
| CMZ = 0.49 + L5 L5 L3 FTY = 165.0 |
| FYLD = 249.9 | L8 fbz = 4.8 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.3 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.7 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.575 3 |
| 132.01 T 0.0 0.3 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
26 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 11 of 91
Job No Sheet No Rev
12
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 27 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 27 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 129.9 |
| KL/R-Z= 19.7 + fa = 31.2 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 180.0 + FTZ = 165.0 |
| CMY = 0.74 | L3 FCY = 165.0 |
| CMZ = 0.85 + L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 5.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.271 5 |
| 50.49 C 0.0 -0.4 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
27 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 12 of 91
Job No Sheet No Rev
13
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 28 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 28 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.5( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 129.9 |
| KL/R-Z= 19.7 + L3 fa = 47.5 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.84 | L3 L3 FCY = 165.0 |
| CMZ = 0.80 + L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 4.1 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.2 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.389 5 |
| 76.97 C 0.0 -0.3 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
28 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 13 of 91
Job No Sheet No Rev
14
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 29 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 29 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 129.9 |
| KL/R-Z= 19.7 + fa = 19.8 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 180.0 + FTZ = 165.0 |
| CMY = 0.40 | L3 L3 FCY = 165.0 |
| CMZ = 0.92 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 6.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 0.5 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.190 5 |
| 32.08 C 0.0 -0.4 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
29 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 14 of 91
Job No Sheet No Rev
15
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 30 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 30 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 129.9 |
| KL/R-Z= 19.7 + L3 fa = 13.7 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 180.0 + FTZ = 165.0 |
| CMY = 0.72 | L3 FCY = 165.0 |
| CMZ = 0.99 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 6.1 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.146 5 |
| 22.16 C 0.0 -0.4 0.42 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
30 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 15 of 91
Job No Sheet No Rev
16
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 31 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 31 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 1.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 129.9 |
| KL/R-Z= 19.7 + fa = 12.6 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 180.0 + FTZ = 165.0 |
| CMY = 0.83 | L3 FCY = 165.0 |
| CMZ = 0.83 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 9.9 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.6 |
| DFF = 0.0 0.5 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.4 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.165 5 |
| 20.37 C 0.0 -0.7 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
31 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 16 of 91
Job No Sheet No Rev
17
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 32 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 32 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 0.49 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 1.0( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 25.6 | L3 FA = 150.0 |
| KL/R-Z= 9.7 + L3 L3 fa = 17.8 |
| UNL = 492.2 | L3 L3 FCZ = 163.3 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.97 | L3 FCY = 165.0 |
| CMZ = 0.40 + L3 L4 FTY = 165.0 |
| FYLD = 249.9 | L4 fbz = 14.7 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.7 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 5.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.212 3 |
| 28.89 T 0.0 1.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
32 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 17 of 91
Job No Sheet No Rev
18
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 33 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 33 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 92.7 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| FAIL COMPRESSION 1.030 3 |
| 80.29 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
* 33 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 18 of 91
Job No Sheet No Rev
19
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 34 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 34 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 74.1 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.824 3 |
| 64.18 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
34 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 19 of 91
Job No Sheet No Rev
20
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 35 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 35 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 54.0 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.600 3 |
| 46.76 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
35 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 20 of 91
Job No Sheet No Rev
21
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 36 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 36 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 35.6 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.396 3 |
| 30.86 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
36 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 21 of 91
Job No Sheet No Rev
22
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 37 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 37 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 16.6 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.185 3 |
| 14.40 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
37 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 22 of 91
Job No Sheet No Rev
23
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 38 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 38 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 150.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 4.5 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 400.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS TENSION 0.030 8 |
| 3.88 T 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
38 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 23 of 91
Job No Sheet No Rev
24
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 39 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 39 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 150.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 23.0 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 400.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS TENSION 0.153 3 |
| 19.91 T 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
39 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 24 of 91
Job No Sheet No Rev
25
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 40 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 40 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.04 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 35.3 |L0 L0 FA = 150.0 |
| KL/R-Z= 71.4 +L0 L0 fa = 25.8 |
| UNL = 1042.4 |L0 L0 FCZ = 0.0 |
| C = 400.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS TENSION 0.172 3 |
| 22.30 T 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
40 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 25 of 91
Job No Sheet No Rev
26
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 51 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 51 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER |L5 STRESSES |
|IN NEWT MM | L5 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 52.0 | L5 FA = 129.9 |
| KL/R-Z= 19.7 + L5 fa = 22.3 |
| UNL = 1000.0 | L5 L3 FCZ = 155.8 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.62 | FCY = 165.0 |
| CMZ = 0.42 + L5 L3 FTY = 165.0 |
| FYLD = 249.9 | L8 L3 fbz = 8.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.3 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(B) 0.204 5 |
| 36.10 C 0.0 -0.6 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
51 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 26 of 91
Job No Sheet No Rev
27
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 52 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 52 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.6( KN-METR) |
|PARAMETER | L5 STRESSES |
|IN NEWT MM | L5 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 52.0 | L5 FA = 129.9 |
| KL/R-Z= 19.7 +L3 L5 fa = 44.7 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.58 | L3 FCY = 165.0 |
| CMZ = 0.40 + L3 L5 FTY = 165.0 |
| FYLD = 249.9 | L6 fbz = 8.7 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.4 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.368 5 |
| 72.35 C 0.0 -0.6 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
52 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 27 of 91
Job No Sheet No Rev
28
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 53 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 53 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.4( KN-METR) |
|PARAMETER | L5 L5 L5 STRESSES |
|IN NEWT MM | L5 L5 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 52.0 | L5 L5 FA = 129.9 |
| KL/R-Z= 19.7 + fa = 68.7 |
| UNL = 999.9 | L5 FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.40 | FCY = 165.0 |
| CMZ = 0.92 + L5 FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 5.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 0.3 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.562 5 |
| 111.20 C 0.0 -0.4 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
53 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 28 of 91
Job No Sheet No Rev
29
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 54 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 54 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.3( KN-METR) |
|PARAMETER | L5 STRESSES |
|IN NEWT MM | L5 IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 52.0 | L5 FA = 129.9 |
| KL/R-Z= 19.7 + L5 fa = 57.3 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 +L5 L5 FTZ = 165.0 |
| CMY = 0.47 | L3 L5 FCY = 165.0 |
| CMZ = 0.45 + L3 FTY = 165.0 |
| FYLD = 249.9 | L7 fbz = 5.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.4 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.6 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.457 5 |
| 92.78 C 0.0 -0.3 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
54 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 29 of 91
Job No Sheet No Rev
30
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 55 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 55 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.5( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L5 L3 IN NEWT MM|
|--------------- + L5 L5 -------------|
| KL/R-Y= 52.0 | FA = 129.9 |
| KL/R-Z= 19.7 + L5 L5 fa = 74.9 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.60 | L5 FCY = 165.0 |
| CMZ = 0.90 + L5 FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 6.7 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.3 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.616 5 |
| 121.20 C 0.0 -0.4 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
55 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 30 of 91
Job No Sheet No Rev
31
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 56 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 56 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.4( KN-METR) |
|PARAMETER |L3 L5 STRESSES |
|IN NEWT MM | L5 IN NEWT MM|
|--------------- + L5 L5 -------------|
| KL/R-Y= 52.0 | FA = 129.9 |
| KL/R-Z= 19.7 + L5 L5 fa = 76.0 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.56 | L5 FCY = 165.0 |
| CMZ = 0.87 + L5 FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 6.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.3 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.622 5 |
| 123.07 C 0.0 -0.4 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
56 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 31 of 91
Job No Sheet No Rev
32
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 57 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 57 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 1.3( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + fa = 83.9 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.45 | L3 FCY = 165.0 |
| CMZ = 0.68 + L5 L3 FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 19.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 0.2 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.6 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.675 3 |
| 135.91 T 0.0 1.3 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
57 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 32 of 91
Job No Sheet No Rev
33
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 58 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 58 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 0.49 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 2.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 25.6 |L3 L3 FA = 150.0 |
| KL/R-Z= 9.7 + L3 fa = 81.6 |
| UNL = 492.2 | L3 FCZ = 163.3 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.55 | FCY = 165.0 |
| CMZ = 0.40 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 29.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.0 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 10.5 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.734 3 |
| 132.14 T 0.0 -2.0 0.49 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
58 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 33 of 91
Job No Sheet No Rev
34
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 59 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 59 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.2( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L5 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 89.5 |
| UNL = 1000.0 | L5 FCZ = 155.8 |
| C = 400.0 + L6 L5 FTZ = 165.0 |
| CMY = 0.78 | L6 FCY = 165.0 |
| CMZ = 0.40 + L5 FTY = 165.0 |
| FYLD = 249.9 | L8 L8 fbz = 3.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.6 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.619 3 |
| 144.91 T 0.0 -0.2 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
59 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 34 of 91
Job No Sheet No Rev
35
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 60 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 60 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.4( KN-METR) |
|PARAMETER | L5 L5 STRESSES |
|IN NEWT MM | L5 L5 IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 52.0 | L5 FA = 150.0 |
| KL/R-Z= 19.7 + L5 fa = 46.5 |
| UNL = 999.9 | FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.47 | L5 FCY = 165.0 |
| CMZ = 0.80 + L5 FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 5.2 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.2 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.341 3 |
| 75.22 T 0.0 0.3 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
60 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 35 of 91
Job No Sheet No Rev
36
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 61 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 61 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.3( KN-METR) |
|PARAMETER | L5 L5 STRESSES |
|IN NEWT MM | L5 IN NEWT MM|
|--------------- + L5 L5 -------------|
| KL/R-Y= 52.0 | FA = 150.0 |
| KL/R-Z= 19.7 + L5 L5 fa = 65.3 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.77 | L5 FCY = 165.0 |
| CMZ = 0.71 + L5 FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 3.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.457 3 |
| 105.69 T 0.0 0.2 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
61 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 36 of 91
Job No Sheet No Rev
37
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 62 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 62 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.4( KN-METR) |
|PARAMETER | L5 L5 STRESSES |
|IN NEWT MM | L5 L5 IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 52.0 | L5 FA = 150.0 |
| KL/R-Z= 19.7 + L5 fa = 32.6 |
| UNL = 1000.0 | FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.68 | L5 FCY = 165.0 |
| CMZ = 0.89 + L5 FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 6.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 0.3 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.257 3 |
| 52.85 T 0.0 0.4 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
62 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 37 of 91
Job No Sheet No Rev
38
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 63 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 63 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.4( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | FA = 150.0 |
| KL/R-Z= 19.7 + L5 L5 L3 fa = 24.0 |
| UNL = 1000.0 | L5 L3 FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.82 | L5 FCY = 165.0 |
| CMZ = 0.97 + FTY = 165.0 |
| FYLD = 249.9 |L5 fbz = 6.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.199 3 |
| 38.84 T 0.0 0.4 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
63 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 38 of 91
Job No Sheet No Rev
39
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 64 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 64 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.7( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + fa = 20.3 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.87 | L3 FCY = 165.0 |
| CMZ = 0.83 + L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 10.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.4 |
| DFF = 0.0 0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.5 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.200 3 |
| 32.84 T 0.0 0.7 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
64 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 39 of 91
Job No Sheet No Rev
40
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 65 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 65 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 27.3 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 0.49 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.7( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 25.6 | L5 L3 FA = 150.0 |
| KL/R-Z= 9.7 + fa = 22.5 |
| UNL = 492.2 | L5 L3 FCZ = 163.3 |
| C = 400.0 + L5 L3 FTZ = 165.0 |
| CMY = 0.97 | FCY = 165.0 |
| CMZ = 0.40 + L3 FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 10.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.4 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 4.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.215 3 |
| 36.40 T 0.0 0.7 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
65 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 40 of 91
Job No Sheet No Rev
41
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 66 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 66 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 72.5 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.806 3 |
| 62.83 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
66 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 41 of 91
Job No Sheet No Rev
42
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 67 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 67 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 59.5 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.661 3 |
| 51.49 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
67 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 42 of 91
Job No Sheet No Rev
43
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 68 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 68 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 46.2 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.513 3 |
| 40.01 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
68 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 43 of 91
Job No Sheet No Rev
44
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 69 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 69 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 33.9 |
| UNL = 1317.7 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.377 3 |
| 29.36 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
69 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 44 of 91
Job No Sheet No Rev
45
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 70 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 70 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 21.2 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.236 3 |
| 18.38 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
70 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 45 of 91
Job No Sheet No Rev
46
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 71 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 71 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 9.1 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.101 3 |
| 7.89 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
71 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 46 of 91
Job No Sheet No Rev
47
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 72 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 72 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.32 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 44.7 |L0 L0 FA = 90.0 |
| KL/R-Z= 90.3 +L0 L0 fa = 12.1 |
| UNL = 1317.8 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.134 5 |
| 10.48 C 0.0 0.0 1.32 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
72 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 47 of 91
Job No Sheet No Rev
48
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 73 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 73 * | INDIAN SECTIONS | AX = 8.7 |
| * | ST ISA75X75X6 | --Z AY = 3.0 |
|DESIGN CODE * | | AZ = 3.0 |
| IS-800 * =============================== SY = 14.2 |
| * SZ = 6.2 |
| * |<---LENGTH (ME= 1.04 --->| RY = 2.9 |
|************* RZ = 1.5 |
| |
| 0.0( KN-METR) |
|PARAMETER |L0 L0 STRESSES |
|IN NEWT MM |L0 L0 IN NEWT MM|
|--------------- +L0 L0 -------------|
| KL/R-Y= 35.3 |L0 L0 FA = 110.1 |
| KL/R-Z= 71.4 +L0 L0 fa = 13.4 |
| UNL = 1042.4 |L0 L0 FCZ = 0.0 |
| C = 180.0 +L0 L0 FTZ = 0.0 |
| CMY = 0.00 |L0 L0 FCY = 0.0 |
| CMZ = 0.00 +L0 L0 FTY = 0.0 |
| FYLD = 249.9 |L0 L0 fbz = 0.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS COMPRESSION 0.121 5 |
| 11.57 C 0.0 0.0 1.04 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
73 ST ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 48 of 91
Job No Sheet No Rev
49
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 84 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 84 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 4.2( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 150.0 |
| KL/R-Z= 50.5 + L3 fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 180.0 + FTZ = 165.0 |
| CMY = 0.60 | L3 FCY = 165.0 |
| CMZ = 0.60 + FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 30.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 -0.2 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.283 3 |
| 0.03 T 0.0 4.2 2.09 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
84 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 49 of 91
Job No Sheet No Rev
50
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 85 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 85 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.2( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.5 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 80.1 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.7 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.775 3 |
| 1.18 C -0.1 11.2 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
85 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 50 of 91
Job No Sheet No Rev
51
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 86 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 86 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 6.7( KN-METR) |
|PARAMETER | L3 L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | FA = 40.6 |
| KL/R-Z= 50.5 + L3 fa = 1.1 |
| UNL = 3575.0 | FCZ = 107.2 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | L3 FCY = 165.0 |
| CMZ = 0.60 + FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 48.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 1.2 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.485 3 |
| 2.75 C -0.1 6.7 2.68 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
86 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 51 of 91
Job No Sheet No Rev
52
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 87 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 87 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.3( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 150.0 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 80.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 5.6 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.768 3 |
| 0.02 T -0.1 11.3 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
87 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 52 of 91
Job No Sheet No Rev
53
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 88 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 88 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.1( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 1.7 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 79.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.7 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.799 3 |
| 4.07 C -0.1 11.1 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
88 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 53 of 91
Job No Sheet No Rev
54
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 89 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 89 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.2( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 80.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.7 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.765 3 |
| 0.00 C -0.1 11.2 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
89 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 54 of 91
Job No Sheet No Rev
55
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 90 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 90 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.2( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 80.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.8 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.763 3 |
| 0.01 C -0.1 11.2 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
90 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 55 of 91
Job No Sheet No Rev
56
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 91 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 91 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.4( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 150.0 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 81.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 6.0 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.779 3 |
| 0.00 T -0.1 11.4 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
91 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 56 of 91
Job No Sheet No Rev
57
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 92 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 92 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 11.2( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 150.0 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 80.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 6.0 |
| DFF = 0.0 -0.6 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.767 3 |
| 0.03 T -0.1 11.2 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
92 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 57 of 91
Job No Sheet No Rev
58
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 101 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 101 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.5( KN-METR) |
|PARAMETER | L5 L5 L5 STRESSES |
|IN NEWT MM | L5 L5 IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 160.5 | L5 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.7 |
| UNL = 3575.0 | L5 FCZ = 107.2 |
| C = 180.0 + L5 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L5 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 53.4 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 3.1 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.535 3 |
| 1.79 C 0.1 7.5 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
101 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 58 of 91
Job No Sheet No Rev
59
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 102 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 102 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 5.3( KN-METR) |
|PARAMETER | L5 L5 L5 L5 L5 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L5 L5 -------------|
| KL/R-Y= 160.5 | FA = 150.0 |
| KL/R-Z= 50.5 + L5 fa = 0.8 |
| UNL = 3575.0 | FCZ = 107.2 |
| C = 180.0 + L5 FTZ = 165.0 |
| CMY = 0.60 | L5 FCY = 165.0 |
| CMZ = 0.60 + FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 37.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.1 |
| DFF = 0.0 -0.3 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.357 5 |
| 2.00 T 0.0 -5.3 2.98 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
102 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 59 of 91
Job No Sheet No Rev
60
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 103 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 103 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.5( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 150.0 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 53.7 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 1.5 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.519 4 |
| 0.05 T 0.1 7.5 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
103 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 60 of 91
Job No Sheet No Rev
61
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 104 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 104 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.4( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 1.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 53.1 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 3.2 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.538 4 |
| 2.42 C 0.1 7.4 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
104 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 61 of 91
Job No Sheet No Rev
62
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 105 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 105 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.5( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 53.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.9 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.517 4 |
| 0.01 C 0.1 7.5 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
105 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 62 of 91
Job No Sheet No Rev
63
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 106 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 106 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.5( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 53.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 2.9 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.515 4 |
| 0.00 C 0.1 7.5 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
106 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 63 of 91
Job No Sheet No Rev
64
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 107 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 107 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 24.0 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.6( KN-METR) |
|PARAMETER | L4 L4 L4 STRESSES |
|IN NEWT MM | L4 L4 IN NEWT MM|
|--------------- + L4 -------------|
| KL/R-Y= 160.5 | L4 FA = 40.6 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L4 FCZ = 107.2 |
| C = 180.0 + L4 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L4 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 54.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 3.1 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.527 4 |
| 0.00 C 0.1 7.6 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
107 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 64 of 91
Job No Sheet No Rev
65
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 108 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 108 * | INDIAN SECTIONS | | AX = 24.4 |
| * | ST ISMC175 | | --Z AY = 10.0 |
|DESIGN CODE * | | | AZ = 10.2 |
| IS-800 * =============================== |=== SY = 49.3 |
| * SZ = 139.8 |
| * |<---LENGTH (ME= 3.57 --->| RY = 2.2 |
|************* RZ = 7.1 |
| |
| 7.6( KN-METR) |
|PARAMETER | L3 L3 L3 STRESSES |
|IN NEWT MM | L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 160.5 | L3 FA = 150.0 |
| KL/R-Z= 50.5 + fa = 0.0 |
| UNL = 3575.0 | L3 FCZ = 107.2 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.60 + L3 FTY = 165.0 |
| FYLD = 249.9 |L0 fbz = 54.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 1.3 |
| DFF = 0.0 -0.4 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.525 3 |
| 0.03 T 0.1 7.6 3.57 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
108 ST ISMC175 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 65 of 91
Job No Sheet No Rev
66
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 361 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ==||== ------------ |
|MEMBER 361 * | INDIAN SECTIONS | || AX = 17.3 |
| * | LD ISA75X75X6 | || --Z AY = 6.0 |
|DESIGN CODE * | | || AZ = 6.0 |
| IS-800 * |-----------------------------| || SY = 25.5 |
| * SZ = 17.3 |
| * |<---LENGTH (ME= 3.71 --->| RY = 3.4 |
|************* RZ = 2.3 |
| |
| 1.3( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 108.9 | L3 L3 FA = 41.0 |
| KL/R-Z= 159.5 + fa = 7.4 |
| UNL = 3712.2 | L3 L3 FCZ = 120.0 |
| C = 180.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.40 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L6 fbz = 75.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 10.9 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(B) 0.745 3 |
| 12.82 C 0.3 1.3 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
361 LD ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 66 of 91
Job No Sheet No Rev
67
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 362 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ==||== ------------ |
|MEMBER 362 * | INDIAN SECTIONS | || AX = 17.3 |
| * | LD ISA75X75X6 | || --Z AY = 6.0 |
|DESIGN CODE * | | || AZ = 6.0 |
| IS-800 * |-----------------------------| || SY = 25.5 |
| * SZ = 44.8 |
| * |<---LENGTH (ME= 3.71 --->| RY = 3.4 |
|************* RZ = 2.3 |
| |
| 1.3( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 108.9 | L3 L3 FA = 150.0 |
| KL/R-Z= 159.5 + fa = 12.2 |
| UNL = 3712.2 | L3 L3 FCZ = 120.0 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.40 | L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L6 fbz = 29.0 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 7.6 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.670 3 |
| 21.08 T 0.2 1.3 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
362 LD ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 67 of 91
Job No Sheet No Rev
68
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 363 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ==||== ------------ |
|MEMBER 363 * | INDIAN SECTIONS | || AX = 17.3 |
| * | LD ISA75X75X6 | || --Z AY = 6.0 |
|DESIGN CODE * | | || AZ = 6.0 |
| IS-800 * |-----------------------------| || SY = 25.5 |
| * SZ = 17.3 |
| * |<---LENGTH (ME= 3.71 --->| RY = 3.4 |
|************* RZ = 2.3 |
| |
| 1.2( KN-METR) |
|PARAMETER | L5 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 108.9 |L4 FA = 41.0 |
| KL/R-Z= 159.5 + L5 L5 L5 fa = 8.9 |
| UNL = 3712.2 | L5 FCZ = 120.0 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.40 | L5 L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L6 fbz = 67.9 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 6.3 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(B) 0.663 5 |
| 15.33 C -0.2 1.2 3.71 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
363 LD ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 68 of 91
Job No Sheet No Rev
69
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 364 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ==||== ------------ |
|MEMBER 364 * | INDIAN SECTIONS | || AX = 17.3 |
| * | LD ISA75X75X6 | || --Z AY = 6.0 |
|DESIGN CODE * | | || AZ = 6.0 |
| IS-800 * |-----------------------------| || SY = 25.5 |
| * SZ = 44.8 |
| * |<---LENGTH (ME= 3.71 --->| RY = 3.4 |
|************* RZ = 2.3 |
| |
| 1.2( KN-METR) |
|PARAMETER | L5 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- +L4 L5 -------------|
| KL/R-Y= 108.9 | L5 FA = 150.0 |
| KL/R-Z= 159.5 + L5 L5 fa = 5.3 |
| UNL = 3712.2 | L5 FCZ = 120.0 |
| C = 180.0 + L5 FTZ = 165.0 |
| CMY = 0.40 | L5 L5 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L6 fbz = 26.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 8.7 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 1.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS 7.1.2 BEND C 0.618 5 |
| 9.20 T -0.2 1.2 3.71 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
364 LD ISA75X75X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 69 of 91
Job No Sheet No Rev
70
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 737 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 737 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 79.1 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.62 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 25.1 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.7 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| FAIL IS-7.1.1(A) 1.283 5 |
| 44.92 C 0.0 -0.1 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
* 737 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 70 of 91
Job No Sheet No Rev
71
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 738 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 738 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 96.2 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.40 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 36.2 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.9 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| FAIL IS-7.1.1(A) 2.014 5 |
| 54.63 C 0.0 -0.1 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
* 738 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 71 of 91
Job No Sheet No Rev
72
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 740 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 740 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM |L3 L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 76.6 |
| KL/R-Z= 104.2 + L3 fa = 63.2 |
| UNL = 1000.0 | L3 FCZ = 136.0 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.60 | L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 19.2 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.5 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.955 5 |
| 35.89 C 0.0 -0.1 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
740 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 72 of 91
Job No Sheet No Rev
73
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 741 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 741 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + L3 fa = 46.2 |
| UNL = 1000.0 | L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.79 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 16.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.4 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.686 5 |
| 26.24 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
741 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 73 of 91
Job No Sheet No Rev
74
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 742 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 742 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM |L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 76.6 |
| KL/R-Z= 104.2 + L3 L3 fa = 32.1 |
| UNL = 1000.0 | L3 FCZ = 136.0 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.40 | L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 11.9 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.468 5 |
| 18.22 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
742 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 74 of 91
Job No Sheet No Rev
75
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 743 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 743 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM |L3 L3 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + L3 fa = 17.3 |
| UNL = 1000.0 | L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.47 | L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 7.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.252 5 |
| 9.82 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
743 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 75 of 91
Job No Sheet No Rev
76
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 744 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 744 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER | L5 STRESSES |
|IN NEWT MM |L5 IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 52.0 | L5 L5 FA = 76.6 |
| KL/R-Z= 104.2 + L5 fa = 5.1 |
| UNL = 1000.0 | L5 FCZ = 136.0 |
| C = 180.0 + L5 L5 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.40 + L5 FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 1.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.0 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.077 8 |
| 2.92 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
744 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 76 of 91
Job No Sheet No Rev
77
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 745 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 745 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 21.5 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 180.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.73 | FCY = 165.0 |
| CMZ = 0.40 + L3 FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 9.7 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.316 3 |
| 12.23 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
745 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 77 of 91
Job No Sheet No Rev
78
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 746 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 746 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== SY = 5.9 |
| * SZ = 3.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- +L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 76.6 |
| KL/R-Z= 104.2 + L3 L3 fa = 36.8 |
| UNL = 1000.0 | L3 FCZ = 136.0 |
| C = 180.0 + L3 FTZ = 165.0 |
| CMY = 0.54 | L3 FCY = 165.0 |
| CMZ = 0.40 + L3 FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 2.8 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 13.2 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.4 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.540 3 |
| 20.92 C 0.1 0.0 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
746 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 78 of 91
Job No Sheet No Rev
79
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 747 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 747 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== SY = 5.9 |
| * SZ = 3.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER |L5 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L5 -------------|
| KL/R-Y= 52.0 | L5 FA = 76.6 |
| KL/R-Z= 104.2 + L5 fa = 6.1 |
| UNL = 1000.0 | L5 L5 FCZ = 136.0 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.74 | L5 FCY = 165.0 |
| CMZ = 0.40 + L5 FTY = 165.0 |
| FYLD = 249.9 | L3 L8 fbz = 3.3 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.1 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.105 4 |
| 3.47 C 0.0 0.0 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
747 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 79 of 91
Job No Sheet No Rev
80
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 748 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 748 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM |L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 104.2 + L3 fa = 10.1 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.40 | L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 8.2 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.117 3 |
| 5.73 T 0.0 0.0 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
748 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 80 of 91
Job No Sheet No Rev
81
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 749 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 749 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM |L3 L3 IN NEWT MM|
|--------------- + L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 76.6 |
| KL/R-Z= 104.2 + L3 fa = 17.3 |
| UNL = 1000.0 | L3 FCZ = 136.0 |
| C = 400.0 + L3 FTZ = 165.0 |
| CMY = 0.47 | L3 FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L3 fbz = 8.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.255 5 |
| 9.82 C 0.0 0.0 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
749 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 81 of 91
Job No Sheet No Rev
82
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 750 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 750 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.0( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 32.1 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.40 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 12.8 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.3 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.471 5 |
| 18.22 C 0.0 0.0 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
750 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 82 of 91
Job No Sheet No Rev
83
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 751 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 751 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 46.2 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.79 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 17.1 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.4 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.688 5 |
| 26.24 C 0.0 0.0 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
751 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 83 of 91
Job No Sheet No Rev
84
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 752 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 752 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 63.2 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.60 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 20.8 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.5 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.1(A) 0.965 5 |
| 35.89 C 0.0 -0.1 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
752 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 84 of 91
Job No Sheet No Rev
85
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 753 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 753 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 79.1 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 400.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.62 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 25.7 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.7 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| FAIL IS-7.1.1(A) 1.290 5 |
| 44.92 C 0.0 -0.1 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
* 753 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 85 of 91
Job No Sheet No Rev
86
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 754 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| ------------ |
|MEMBER 754 * | INDIAN SECTIONS | AX = 5.7 |
| * | ST ISA50X50X6 | --Z AY = 2.0 |
|DESIGN CODE * | | AZ = 2.0 |
| IS-800 * =============================== |
| * SZ = 2.7 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 1.0 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 L3 STRESSES |
|IN NEWT MM | IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 L3 FA = 76.6 |
| KL/R-Z= 104.2 + fa = 96.2 |
| UNL = 1000.0 | L3 L3 FCZ = 136.0 |
| C = 180.0 + L3 L3 FTZ = 165.0 |
| CMY = 0.40 | FCY = 165.0 |
| CMZ = 0.40 + FTY = 165.0 |
| FYLD = 249.9 | L5 fbz = 34.6 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.0 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.9 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| FAIL IS-7.1.1(A) 1.980 5 |
| 54.63 C 0.0 -0.1 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
* 754 ST ISA50X50X6 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 86 of 91
Job No Sheet No Rev
87
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 755 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 755 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.2( KN-METR) |
|PARAMETER | L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + L3 L3 -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + fa = 119.0 |
| UNL = 1000.0 | L3 L3 FCZ = 155.8 |
| C = 400.0 + FTZ = 165.0 |
| CMY = 0.47 | L3 FCY = 165.0 |
| CMZ = 0.84 + L3 L3 FTY = 165.0 |
| FYLD = 249.9 |L3 fbz = 2.5 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.1 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.1 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.809 3 |
| 192.68 T 0.0 -0.2 1.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
755 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 87 of 91
Job No Sheet No Rev
88
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

Steel Design (Track 2) Beam 756 Check 1


|--------------------------------------------------------------------------|
| Y PROPERTIES |
|************* | IN CM UNIT |
| * |=============================| |=== ------------ |
|MEMBER 756 * | INDIAN SECTIONS | | AX = 16.2 |
| * | ST ISMC125 | | --Z AY = 6.2 |
|DESIGN CODE * | | | AZ = 7.0 |
| IS-800 * =============================== |=== SY = 13.9 |
| * SZ = 66.6 |
| * |<---LENGTH (ME= 1.00 --->| RY = 1.9 |
|************* RZ = 5.1 |
| |
| 0.1( KN-METR) |
|PARAMETER |L3 STRESSES |
|IN NEWT MM | L3 IN NEWT MM|
|--------------- + -------------|
| KL/R-Y= 52.0 | L3 FA = 150.0 |
| KL/R-Z= 19.7 + L3 fa = 119.3 |
| UNL = 1000.0 | L3 FCZ = 155.8 |
| C = 400.0 + L5 FTZ = 165.0 |
| CMY = 0.40 | L5 FCY = 165.0 |
| CMZ = 0.60 + L5 L5 FTY = 165.0 |
| FYLD = 249.9 | L5 L5 fbz = 1.8 |
| NSF = 1.0 +---+---+---+---+---+---+---+---+---+---| fby = 0.2 |
| DFF = 0.0 0.0 FV = 100.0 |
| dff = 0.0 ABSOLUTE MZ ENVELOPE fv = 0.2 |
| (WITH LOAD NO.) |
| |
| MAX FORCE/ MOMENT SUMMARY ( KN-METR) |
| ------------------------- |
| |
| AXIAL SHEAR-Y SHEAR-Z MOMENT-Y MOMENT-Z |
| |
| VALUE 0.0 0.0 0.0 0.0 0.0 |
| LOCATION 0.0 0.0 0.0 0.0 0.0 |
| LOADING 0 0 0 0 0 |
| |
|**************************************************************************|
|* *|
|* DESIGN SUMMARY ( KN-METR) *|
|* -------------- *|
|* *|
|* RESULT/ CRITICAL COND/ RATIO/ LOADING/ *|
| FX MY MZ LOCATION |
| ====================================================== |
| PASS IS-7.1.2 0.808 3 |
| 193.08 T 0.0 -0.1 0.00 |
|* *|
|**************************************************************************|
| |
|--------------------------------------------------------------------------|
756 ST ISMC125 (INDIAN SECTIONS)

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 88 of 91
Job No Sheet No Rev
89
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

7.10m

7.15m

Y 8.00m 14.85m
X
Z Load 1

Whole Structure

8.00m
7.15m
7.10m 14.85m

Y
Z X
Load 1

Front View

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 89 of 91
Job No Sheet No Rev
90
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

7.10m 7.15m 8.00m 14.85m

Y
X Z
Load 1

Whole Structure

7.10m

7.15m

8.00m

Y X
Load 1
Z
14.85m
Whole Structure

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 90 of 91
Job No Sheet No Rev
91
Part
Software licensed to
Job Title ROOF TRUSS FOR PUMP HOUSE Ref

By Date12-May-15 Chd

Client GLIS-III,PKG-IV-BOMMAKUR File Roof Truss - Bommakur P Date/Time 16-Jun-2015 11:11

3D Rendered View

Print Time/Date: 16/06/2015 11:12 STAAD.Pro for Windows 20.07.04.12 Print Run 91 of 91
Support Reactions (DL+LL)
Moment‐X  Moment‐Y  Moment‐Z 
Node L/C Force‐X kN Force‐Y kN Force‐Z kN
kNm kNm kNm
56 5 ‐168.944 81.427 0.081 0 0 0
37 5 168.936 81.425 0.081 0 0 0
21 5 ‐157.167 75.844 ‐0.08 0 0 0
1 5 157.155 75.841 ‐0.08 0 0 0
37 2 102.264 48.654 0.02 0 0 0
56 2 ‐102.262 48.654 0.02 0 0 0
141 5 91.92 46.501 ‐0.006 0 0 0
151 5 ‐91.911 46.182 ‐0.005 0 0 0
1 2 96.223 45.834 ‐0.02 0 0 0
21 2 ‐96.221 45.833 ‐0.02 0 0 0
72 5 80.899 40.868 0.005 0 0 0
91 5 ‐80.889 40.549 0.005 0 0 0
56 1 ‐66.682 32.773 0.061 0 0 0
37 1 66.672 32.771 0.061 0 0 0
21 1 ‐60.946 30.011 ‐0.06 0 0 0
1 1 60.932 30.007 ‐0.06 0 0 0
151 2 ‐50.029 25.136 ‐0.002 0 0 0
141 2 50.027 25.136 ‐0.002 0 0 0
91 2 ‐44.254 22.22 0.002 0 0 0
72 2 44.252 22.22 0.002 0 0 0
141 1 41.892 21.365 ‐0.003 0 0 0
151 1 ‐41.882 21.046 ‐0.003 0 0 0
72 1 36.648 18.648 0.002 0 0 0
91 1 ‐36.635 18.329 0.002 0 0 0
Support Reactions (DL+WL)
Moment‐X  Moment‐Y  Moment‐Z 
Node L/C Force‐X kN Force‐Y kN Force‐Z kN
kNm kNm kNm
37 2 102.264 48.654 0.02 0 0 0
56 2 ‐102.262 48.654 0.02 0 0 0
1 2 96.223 45.834 ‐0.02 0 0 0
21 2 ‐96.221 45.833 ‐0.02 0 0 0
56 1 ‐66.682 32.773 0.061 0 0 0
37 1 66.672 32.771 0.061 0 0 0
21 1 ‐60.946 30.011 ‐0.06 0 0 0
1 1 60.932 30.007 ‐0.06 0 0 0
151 2 ‐50.029 25.136 ‐0.002 0 0 0
141 2 50.027 25.136 ‐0.002 0 0 0
91 2 ‐44.254 22.22 0.002 0 0 0
72 2 44.252 22.22 0.002 0 0 0
141 1 41.892 21.365 ‐0.003 0 0 0
151 1 ‐41.882 21.046 ‐0.003 0 0 0
72 1 36.648 18.648 0.002 0 0 0
91 1 ‐36.635 18.329 0.002 0 0 0
91 7 44.373 ‐19.454 ‐0.001 0 0 0
91 6 51.411 ‐21.263 ‐0.001 0 0 0
151 7 49.686 ‐21.696 0.001 0 0 0
151 6 57.635 ‐23.742 0.001 0 0 0
72 7 ‐44.077 ‐24.543 ‐0.002 0 0 0
141 7 ‐49.406 ‐27.502 0.002 0 0 0
72 6 ‐50.949 ‐29.58 ‐0.003 0 0 0
141 6 ‐57.197 ‐33.204 0.002 0 0 0
21 7 115.045 ‐47.925 ‐0.031 0 0 0
56 7 120.357 ‐49.955 0.032 0 0 0
21 6 130.262 ‐51.656 ‐0.033 0 0 0
56 6 136.529 ‐53.914 0.033 0 0 0
1 7 ‐115.321 ‐59.214 ‐0.018 0 0 0
37 7 ‐120.656 ‐61.94 0.019 0 0 0
1 6 ‐130.693 ‐69.678 ‐0.012 0 0 0
37 6 ‐136.999 ‐73.048 0.013 0 0 0
DESIGN OF BASE PLATE 

DL+LL DL+WL
Bending Moment Kn.m 0.00 0.00
Shear Force (Fx) Kn 169.00 137.00 2 BOLTS ‐ 3REACTIONS 
Axial Force (Fy) Kn 81.00 73.00 DL : DEAD LOAD
Web Depth mm LL : LIVE LOAD
Flange Depth mm WL : WIND LOAD
Bolts Dia mm 20
Embed length (Le) mm 600
Plate Thickness (t) mm 16
Pitch (p) mm 120
guage (g) mm 250
No. COLS ALONG LEN 1 SIDE 1
No. Of Bolts ALONG WIDTH : 4
No. Of Bolts (n) 8 DON’T ENTER VALUE
WEB DEPTH  : 150 mm
PLATE LENGTH   : 400 mm
PLATE WIDTH    : 400 mm
CHECK SPACING : 280 SAFE
GRADE OF CONCRET : 25 N/mm^2

Distance of the extreme Tension Fiber(L) : 150 mm
 
Effective Lever arm :
: 125 mm
Total Tension in each extreme Bolts ( T )
Total Tension in each extreme Bolts ( T ) : Maximum
Maximum moment / Eff. Lever arm
moment / Eff. Lever arm
: 0 / 0.13
: 0.00 Kn
CHECK FOR BOLT SIZE

FORCES IN THE BOLTS Actual  Allowable


(Kn) (Kn)
Max. Tension in each Bolt  : 0.00

Tension due to Axial Force ( Fy/n )UPLIFT : 9.13

Total Tension ( P= T/4+Fy/n) : 9.13 32.70 HENCE SAFE

Shear in each Bolt ( Fx/n) : 21.13 21.30 HENCE SAFE

CHECK FOR THICKNESS OF PLATE
P
Maximum bending moment in the plate(Ma)           :  P x g/ 4
( About criticle section X‐X) :   9.13 x 250/4
: 0.57 Kn‐M G
250
Thickness of plate required ( t ) :    6 x Ma / f x p

: 13.23 < 16 MM HENCE SAFE

CHECK FOR COMBINED TENSION AND SHEAR

Actual Tension + Actual Shear   < 1. 4


Allowable Tension Allowable Shear

(9.13 / 32.7)+(21.13 / 21.3)   = 1.27 < 1.4 HENCE SAFE


CHECK FOR BOLT LENGTH

Bond Stre gra. OF Cocrete  M 25 : 0.90 N/mm2

Length of bolt required : Tension in bolt/(p x bolt Dia.)x Bond stress
:   9.13 *1000/(p* 20)*0.9
: 161 mm HENCE SAFE

CHECK FOR BASE PLATE SIZE

Area of Base Plate (A) : 400x400  = 160000 mm2


Pres. On concrete pedestal (P/A+M/Z) DL+LL : 0.0 N/mm2

Pres on concrete pedestal (P/A+M/Z) DL+WL : 0.0

Allowable pressure below the base plate : 6.0 N/mm2

Allowable pressure > Actual pressure HENCE SAFE

Hence Provide :  16 mm Thick Plate/ 8 No.s 20 mm Dia Anchor Bolts.

You might also like