Scribd
Upload
350 views4 pages

Module 5 Ahmedabad 27 June 2019 PDF

This document contains a module outline for a course on 27 June 2019 in Ahmedabad, India. It includes 40 multiple choice questions covering topics like: 1. Display units, control systems, encoding schemes, and magnetic fields 2. Data storage technologies, analog to digital conversion, and interfacing computer systems 3. Logic gates, combinational logic, and digital signal properties The questions assess understanding of aircraft instrumentation, fiber optics, computer buses, semiconductors, and data transmission standards.

Uploaded by

Rahul As
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
350 views4 pages

Module 5 Ahmedabad 27 June 2019 PDF

This document contains a module outline for a course on 27 June 2019 in Ahmedabad, India. It includes 40 multiple choice questions covering topics like: 1. Display units, control systems, encoding schemes, and magnetic fields 2. Data storage technologies, analog to digital conversion, and interfacing computer systems 3. Logic gates, combinational logic, and digital signal properties The questions assess understanding of aircraft instrumentation, fiber optics, computer buses, semiconductors, and data transmission standards.

Uploaded by

Rahul As
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

MODULE 5 B1 27 JUNE 2019 AHMEDABAD 9.

30AM

1. Generates all single characters, special symbols, straight & curved lines and arcs on display units
a) Stroke Generator

2. Control and display unit FMS allow.... Flight crew ?


a) Make I/p obtain RPM
b) Make input obtain Air speed indicator
c) Provide caution data in alpha numeric form
alphanumeric
d) Position the target command bugs on the altimeter indicator

3. Op code in computer system


a) Decimal code
b) BCD
c) Binary code
d) Set of instructions

4. MTC
MTCS S
a) Motor action always tend to produce motion toward the strongest field
b) An induced voltage is produced only which flux is constant
c) Lenz law determine the polarity often induced voltage

5. Bubble memory for


a) Holding Bulk navigation and aircraft performance data bank
b) C-MOS RAM for specific navigation and performance data
c) UV – PROM for operation program

6. In order to represent analog signal using digital codes?


a) The Signal into set of discrete voltage.
b) The Signal into set of analog voltage.
c) Both

7. A system performing a combined function in which the computer and Display unitunitss are interfaced
with a thrust or power management control system and an automatic flight control ?
a) Greater precision of engine power
b) Greater precision of flight path control
c) Isolate the flight crew from the control loop
d) All

8. Switch is used for Data entry & for automatic check out of the system ?
a) Stand By po sition switch
position
b) Main position switch
c) Go around switch
d) Hold switch

9. Which test is usually incorporates computerized control with display & printouts that indicate what
further action is necessary in order to maintain the equipment ??
equipment??
a) Automatic Test Equipment (ATEATE))
b) On bord diagnostic
c) CMS
d) Replace Line unit

10. 800MX . 1000 TURN IN 1 MICRO SECOND... (1MX =10 Raise to minus 8) ?
Ref.- Voltage induced in a coil = rate of charge of current x no of turns of the coil.
a) 8V
b) 8KV
c) 08V
d) 08KV

Prepared by ANKIT PATEL 9429439460


MODULE 5 B1 27 JUNE 2019 AHMEDABAD 9.30AM

11. LCD power supply


a) AC
b) Current DC
c) Voltage DC

12. Static pressure is fed to ..?


a) Air speed indicator
b) Air speed indicator & Altimeter
c) Air speed indicator & Altimeter & Rate of climb Indicator

13. Diagram Fibre optics


a) single mode
b) step index multimode

14. CRT Gun colour


a) red, yellow and blue
b) red, green and blue
c) green, blue and yellow.

15. The main advantage of using a serial bus in an aircraft is


a) There is no need for data conversion
b) It supports the highest possible data rates
c) Reduction in the size and weight of cabling.

16. Logic gates will only produce a logic 1 output when ever any one, or more, inputs are at logic 1.
whenever ?
1.?
a) NAND
b) NOR
c) X-NOR
d) OR

17. The logical function of a combinational logic circuit can be described by a


a) Truth table
b) Boolean algebra
c) Both 1 & 2

18. Which gate will produce logic 1 output where all input are simulatenously at logic 0 ?
a) NANDgate
b) X- NOR
c) NOR gate

19. Which do not affect logical state of digital state of digital symbol?
a) Invertor
b) Buffer
c) NAND gate

20. Gates will only produce a logic 0 output when all inputs are simultaneously at logic 1 ?
a) NAND gate
b) X- NOR
c) NOR gate

21. In a bipolar ADC a logic 1 in the MSB position indicates:


a) zero input voltage
b) negative input voltage
c) positive input voltage.

Prepared by ANKIT PATEL 9429439460


MODULE 5 B1 27 JUNE 2019 AHMEDABAD 9.30AM

22. When compared with an LCD, a CRT display offers the advantage that:
a) The resolution and focus is better
b) It can be viewed over a large angle
c) It uses low voltages and is more energy efficient.

23. ARINC429 is
a) Bi directional
b) Unidirectional

24. Which of the following type of ADC is the fastest ?


a) Ram type
b) Flash Type
c) Successive approximate type

25. The advantage of DRAM & SRAM is ?


a) DRAM must be refreshed periodically
b) SRAM must be refresh periodically
c) DRAM does not require refreshing

26. The triboelectric series classifies different materials according to how well they create
a) static electricity when rubbed with another material.
b) static electricity when rubbed with same material.

27. Which computer bus is provide timming & control signals throghout the system ?
a) Address bus
b) Control bus
c) Data bus

28. In FMS, Reset signal


a) Input
b) output
c) Re – set
d) Reference signal

29. Semiconductor smaller junctions are susceptible to damage due to


a) Creeping current
b) Electrostatic voltage
c) EMI

30. The functions or capabilities of real-time, critical monitoring, module and/or subassembly failure
isolation and go/no-go alarms are a function of:
a) ECAM
b) CSC
c) BITE
d) ACARS

31. In electric control system, regulator controls:


a) Position
b) Speed
c) Transient Period

32. Basic instruments gets input from air data system


a) HSI, ASI, ROCI
b) VOR Magnetic compass, RMI
c) ASI, VSI, Altimeter

Prepared by ANKIT PATEL 9429439460


MODULE 5 B1 27 JUNE 2019 AHMEDABAD 9.30AM

33. Fibre-optic cables use:


a) reflective cladding
b) refractive cladding
c) an opaque cladding.

34. Convert 11101 to Decimal:


a) 36
b) 57
c) 21
d) 29

35. Convert 541 in hexadecimal


a) 21D
b) 23D
c) 29D
36. ARINC 429
a) Unidirectional
b) Bidirectional

37. The number of twists per given length should be specified in order to achieve the
a) Desired EMI protection.

38. In order to optimise the speed of data transfer and minimise problems associated with reflection and
mismatch, the bus cable must be terminated at each end using a matched .
a) Bus terminator
b) Coupler panel
c) Stud cable

39. Antistatic Material are


a) Cardwood & cotton
b) Glass
c) Polyster

40. Secondary Heading Information is Obtained from


a) Gyro
b) Compass
c) Pitot static system

Prepared by ANKIT PATEL 9429439460

You might also like