STANDARD TECHNICAL DATA SHEET

(1.1 kV GRADE XLPE POWER CABLES)

CUSTOMER : POWERGRID CORPORATION OF INDIA LIMITED

SN Name of manufacturer : As per approved list
Cable Sizes 1 C x 630 3½ C x 300
1 Manufacturer's type designation : A2XWaY A2XWY
2 Applicable standard : ----------------------IS: 7098/PT-I/1988 & its referred specifications----------------------
3 Rated Voltage(volts) : -----------------------1100 V grade------------------------------------------------------
4 Type & Category : FR & C1 FR & C1
5 Suitable for earthed or unearthed system : -----------------------for both-------------------------------------------------------------
6 Continuous current rating when laid in air in a ambient temp. of 50 oC
and for maximum conductor temp. of 70 oC of PVC Cables[ For : 732 410
information only]
7 Rating factors applicable to the current ratings for various conditions
of installation: : -------------------------------As per IS-3961-Pt-II-67--------------------------------------

8 Short circuit Capacity

a) Guranteed Short Circuit Amp. (rms)KA for 0.12 sec duration at rated
conductor temperature of 90 degree C, with an initial peak of 105 KA. : 45 KA 45 KA

b) Maximum Conductor temp. allowed for the short circuit duty (deg
C.) as stated above. : --------------------------------------250 oC------------------------------------------------

9 Conductor
a) Material Stranded Aluminium as per Class 2 of IS : 8130
b) Grade : ------------------------------------- H 2 (Electrolytic grade) -------------------------
c) Cross Section area (Sq.mm.) : 630 300/150
d) Number of wires(No.)minimum : 53 30/15
e) Form of Conductor Stranded compacted
Stranded and compacted circular
circular/sector shaped
f) Direction of lay of stranded layers : -------- Outermost layer shall be R.H lay & opposite in successive layers --------
10 Conductor resistance (DC) at 20 oC per km-maximum 0.0469 0.1 / 0.206
11 Insulation
a) Composition of insulation : -------------------------------------Extruded XLPE as per IS-7098 Part(1)-----------------
b) Nominal thickness of insulation(mm) : 2.8 1.8/1.4
c) Minimum thickness of insulation : 2.42 1.52/1.16
12 Inner Sheath
a) Material : --------------------------------Extruded PVC type ST-2 as per IS-5831-84-----------------
b) Calculated diameter over the laid up cores,(mm) : NA 52
c) Thickness of Sheath (minimum)mm : N.A 0.6
d) Method of extrusion NA Pressure/Vacuum extrusion
13 Armour
a) Type and material of armour Al. Wire[ H4
: Gal. Steel wire
grade]
b) Direction of armouring : ----------------------------------left hand--------------------------------------------------
c) Calculated diameter of cable over inner sheath (under armour), mm
: 33.9 53.2

d)Nominal diameter of round armour wire (minimum) : 2 2.5

e)Guranteed Short circuit capacity of the armour for 0.12 sec at room
temperature. 45 KA 45 KA

f) DC resistance at 20 oC ( /Km) $ 0.577

14 Outer Sheath
a) Material ( PVC Type) : ST-2& FR ST-2& FR
b) Calculated diameter under the sheath : 38.3 59.50
c) Min.thickness of sheath(mm) : 1.72 2.36
d) Guaranteed value of minimum oxygen index of outer sheath at 27 oC
Min 29.0 Min 29.0

e) Guranteed value of minimum temperature index at 21 oxygen index

Min 250 Min 250

f) colour of sheath : Black Black

15 a) Nominal Overall diameter of cable $ $
b) Tolerance on overall diameter (mm) : ---------------------------------+2/-2 mm-----------------------------------------------------
16 Cable Drums : ----------------- shall conform to IS 10418 and technical specification
a) Max./ Standard length per drum for each size of cable ( single
length) with ±5% Tolerance (mtrs) 1000/500 1000/500

b) Non standard drum lengths : Maximum one(1) non standard lengths of each cable size may be
supplied in drums only over & above the standard lengths as specified
above.(if required for completion of project).
17 Whether progressive sequential marking on outer sheath provided at
1 meter interval : ----------------------------------------- YES -------------------------------------------------

18 Identification of cores
a) colour of cores As per IS 7098 Part(1)
b) Numbering : ----------------------------------------- N.A ---------------------------------------------------
19 Whether Cables offered are ISI marked : ----------------------------------------- YES ---------------------------------------------------
20 Whether Cables offered are suitable for laying as per IS 1255
: ----------------------------------------- YES -----------------------------------------------------

$'- As per manufacturer design data

Document No:C:Engg:STD:GTP:1.1 kV XLPE POWER CABLE Page 1 of 3