Driver Panel Setup/Calibration/Test Mode Function 1: Test Mode 1 (t1) Function 2: Relay Test (rt)

10 NOTE: When in the Setup/Calibration/Test Mode the HVAC In Setup/Calibration/Test Mode menu press the DOWN (Blue) In Setup/Calibration/Test Mode menu press the DOWN (Blue)
7 8 9 11 12
or UP (Red) keys to scroll to ''t1” and press ENTER (Fan Speed) or UP (Red) keys to scroll to 'rt' and press ENTER (Fan Speed)
unit is out of operation.
key. key. The display will show the relay or output symbol.
Turn the ignition switch ON to supply power to the unit controller Press DOWN (Blue) or UP (Red) keys to scroll through the
The following tests are available:
and leave the display in the OFF position. function menu.
1. Cooling/Heating Control
Press and hold both DOWN (Blue) and UP (Red) keys Press ENTER (Fan Speed) key and corresponding relay/output is
Press ESCAPE (Mode Select) key to change heating or cooling
simultaneously for 3 seconds (t1 will be displayed). energized.
outputs.
The following functions are available in the Setup/Calibration/Test The following table is used to verify all relay outputs and function Display Description Signal Note
Mode. of heating and cooling.
EL Evaporator low EFRL
Display Description speed relay
Function Relay Relay LED
Output ON Output OFF
13 14 t1 Test Mode 1 - basic test of HVAC unit En Evaporator EFRM
1 2 3 4 5 6 medium speed
Ventilation relay
rt Relay Test
Heating BP, MCV CR Red - ON EH Evaporator high EFRH
Item Description Pr Setup of program number and reading of Firmware
version speed relay
Cooling CR BP, MCV Blue - ON
1. On/Off Key CL Compressor CR Blue icon is ON
CA Calibration of temperature sensors Auto / Reheat CR, BP, MCV Red & clutch relay
2. Mode Select Key (ESCAPE) pulsing Blue - ON
SE Setup of controller
bP Boost pump BPR Red icon is ON
3. Temperature Key (Blue) (DOWN) relay
AL Reading and clearing of alarms
4. Temperature Key (Red) (UP) 2. Blower Speed Control C0 Modulating MCV Low side output - com-
Hr Reading of hourmeter
coolant valve patibility with old
5. Blower Speed Key (ENTER) Press ENTER (Fan Speed) key to change evaporator blower ClimaAIRE I
Press DOWN (Blue) or UP (Red) keys to scroll through the menu speed.
6. Fresh Air Select Key selections. C1 Modulating cool- MCV High side output
The following table is used to verify all relay outputs and functions ant valve
7. A/C Mode Icons Press ENTER (Fan Speed) key to save parameter setting. of evaporator blowers.
d0 Damper output DM Low side output - Fresh
8. Temperature Icons Press ESCAPE (Mode Select) key to leave a parameter Function Relay Relay air damper open (100%),
unchanged. Output ON Output OFF
9. Display d1 Damper input DM High side output - Fresh
Press On/Off key when finished to confirm changes. Low Speed EFL EFH, EFM air damper open (100%)
10. Clutch and Boost Pump Icons
See ClimaAIRE ID Service Manual (TK 60020-3-MM) for Medium Speed EFL, EFM EFH Press ESCAPE (Mode Select) key to continue with another
11. Blower Mode Icons additional information. function.
High Speed EFL, EFM, EFH
12. Fresh Air Mode Icons Press On/Off key when finished to confirm changes and switch
Auto EFL, EFM, EFH OFF (soft restart) the system.
13. Red Alarm
Function 3: Setup Program Number (Pr)
14. Yellow Alarm
3. Fresh Air Control In Setup/Calibration/Test Mode menu press DOWN (Blue) or UP
Press Fresh Air Select key to change position of fresh air (Red) keys to scroll to ''Pr” and press Blower Speed (ENTER)
dampers. key.

The following table is used to verify all relay outputs and functions The Firmware version will be displayed followed by the program
of fresh air dampers. number. To change program number press DOWN (Blue) or UP
(Red) keys as required.
Function Relay Relay Press ENTER (Fan Speed) key to save parameter setting.
Output ON Output OFF
Press ESCAPE (Mode Select) key to leave a parameter
Re-circulation DM unchanged.

Fresh air damper 50% open DM pulsing Press DOWN (Blue) or UP (Red) keys to continue with another
function.
Fresh air damper 100% open DM Press On/Off key when finished to confirm changes and switch
OFF (soft restart) the system.
Function 4: Calibration (CA) Function 5: (continued) Function 6: Reading/Clearing Alarms (AL)
In Setup/Calibration/Test Mode menu press the DOWN (Blue) or After calibration press ESCAPE (Mode Select) key to return to In Setup/Calibration/Test Mode menu press the DOWN (Blue) or
UP (Red) keys to scroll to ''CA” and press ENTER (Fan Speed) Function menu or press On/Off key to switch OFF (soft restart) UP (Red) keys to scroll to ''AL” and press ENTER (Fan Speed)
key. The display will show name of parameter and calibration. the system. key.
Press ENTER (Fan Speed) key again to see its current value. Display Preset Unit Min. value Name
All alarm codes will be displayed for 2 seconds and at the end will
Value Max. value be displayed “dE”.
Press ESCAPE (Mode Select) key to leave a parameter
unchanged. If no alarm is stored “no” will be displayed for 1 second.
Ab 07 C 0C Ambient switch point
Press DOWN (Blue) or UP (Red) keys as required to change the 15 C To keep alarms press On/Off key. The panel will be switched off
value. but the alarms will remain recorded.
Fr -3 C -5 C Evaporator anti-
• The calibration range/correction for temperature sensors is +5 C freeze switch point Press ENTER (Fan Speed) key to clear all alarms. The display
from -1 C to +26 C (30.2 F to 78.8 F). will show “00” then returns to Function menu and display will
rh 01 Reheat mode show “AL'”.
Press ESCAPE (Mode Select) key to save new value and
continue to next parameter. dt 07 C 1C Delta T Alarms cleared through the driver panel will remain in internal Diagnostic Procedures
15 C memory and can be read through connected PC with Service
If On/Off key is pressed now a new value is also saved and the
software installed.
system will restart (soft restart). Ao 00 - Automatic On
Press the On/Off key to switch OFF (soft restart) the system.
Press DOWN (Blue) or UP (Red) keys to select next parameter to LS 17 C 15 C Low set point
continue in calibration. 30 C Alarm Alarm Description
After calibration press ESCAPE (Mode Select) key to return to Code Type
HS 27 C 15 C High set point
Function menu or press On/Off key to switch OFF (soft restart) 30 C 01-04 Not Used
the system.
rt 00 Default value on the 05 RED Clutch cycling
Display Description display
06 RED Long delay of HPCO or LPCO
rA Return air temperature sensor 0C 00 Old ClimaAIRE
07 YELLOW RTS Low
Ct Evaporator coil air temperature sensor un C Celsius/Fahrenheit
08 YELLOW RTS High
At Ambient temperature sensor EL 45 % 0% Low speed of blower
100% 09 YELLOW CTS Low
Using Driver’s Panel
Cf Clutch feedback - no calibration
En 66 % 0% Medium speed of 10 YELLOW CTS High
Ub Battery voltage on PWR - no calibration 100% blower
11 YELLOW ATS Low
Eh 100 % 0% High speed of
100% blower
Function 5: Set up of Controller (SE) 12 YELLOW ATS High
Lt 00 Limited temperature
In Setup/Calibration/Test Mode menu press the DOWN (Blue) or 13-30 Not Used
setpoint
UP (Red) keys to scroll to ''SE” and press ENTER (Fan Speed)
31-37 RED Inverter Alarms
key. The system to check/change the parameters is similar as for EC 00 Economic cool mode
Calibration (CA). The display will show name of parameter and
calibration. HO 0 C 0C Heat offset
5C
Press ENTER (Fan Speed) key again to see its current value.
Lc 00 Lock function
Press ESCAPE (Mode Select) key to leave a parameter Function 7: Reading of Hourmeter (Hr)
unchanged.
In Setup/Calibration/Test Mode menu press the DOWN (Blue) or
Press DOWN (Blue) or UP (Red) keys as required to change the UP (Red) keys to scroll to ''Hr” and press ENTER (Fan Speed)
value. key. Each value will automatically be displayed and at the end will
Press ESCAPE (Mode Select) key to save new value and be displayed “Hr”.
continue to next parameter. Press ENTER (Fan Speed) key to repeat process.
If On/Off key is pressed now a new value is also saved and the Press the DOWN (Blue) or UP (Red) key to select next function
system will restart (soft restart). or press the On/Off key to switch OFF (soft restart) the system. TK 55022-3-PC (Rev. 0, 05/11)
Copyright© 2011 Thermo King Corp., Minneapolis, MN U.S.A.
Press DOWN (Blue) or UP (Red) keys to select next parameter to
Printed in U.S.A.
continue in calibration.