www.kocom.

com

Warranty

To receive after service, have the following ready before you

contact our branches.
1. Name of the product.
2. Model number of the product.
Common Gate Camera
3. The area of problem. [ KVL-C302i / KVL-C303i / KVL-C304i / KVL-TC306i / KVL-TC308i ]
4. Phone number and address at which you can be contacted. [ KEL-312 / KEL-T324 ]

■ Automatically opens common gate while communication with house

Warranty Card
■ For 4 wire type videophone
■ Keypad backlight function - LED lamp
PRODUCT
■ White LED for night detection
MODEL ■ Camera angle control
DATE PURCHASED ■ Conneting upto 32 household
■ Openning function of entrance door using I -button key
WARRANTY PERIOD ■ Function of door release without adaptor
AGENCY ADDRESS ■ Function of two door release type( NO, NC )

KOCOM Warranties the original purchaser of this product as follows.

1) This product is produced under strict quality control and inspection procedures.
2) If this product breaks down during proper use as a result of product defect, KOCOM
will repair it within one year from date of purchase free of charge.
3) The following cases will be subject to charge, even during warranty period:
a. Breakdown during transport, or through careless treatment, by consumer.
b. Breakdown cause by unauthorized repair, or system modification.
c. Breakdown caused by natural disaster or power disorder.

SINCE

KOREA COMMUNICATIONS CO.,LTD

1976

http://www.kocom.com I-BUTTON KEY (option)

E-mail : [email protected]
This manual is based on the date as shown in the right and specifications are subject to
change without notice for quality improvement

KVL/KEL Series 4wire 09.09

 Warnings

Warnings for disposal

Cautions for Safety
● Do not throw used-up battery into fire places, which may cause fire and explosion.

Cautions
Warnings & Cautions for Safety
Cautions for installation
For safe use, please stick to the following cautions.
■ Read this cautions carefully and keep it within easy reach of you. ● The relevant law obliges users to have a qualified electrician carry out wiring work for power supply.
■ For right installation, read this cautions thoroughly. Please install the product according to its Work by disqualified persons may cause fire and electric shock.
specifications.
● Wiring work for communication cables need techniques and experiences. For this type of wiring work, please consult to
■ This Cautions for Safety may include items that are not contained in specifications of the product that
your local sales agent.
consumer purchases.
● According to the standard for electric work and other relevant regulations, install communication cables at the place away
■ Reading this cautions, use the product in a right manner. For further information,
from power cables. The failure to install cables separately may cause fire, electric shock and communication troubles.
please contact our A/S center.
● Do not install the product on rolling table or sloping place. Dropping or falling may cause damage on your product.
About symbol ● In installation, avoid the place exposed to tremor or shocks, which may cause damages on your product.
A variety of symbols are used in this Cautions for Safety and your products to guide you to use ● Even if your product is waterproof, do not install it slanted place of water leakage, which may cause a short circuit.
products in a right and safe manner and to prevent possible risks for users and other persons and
● For the product of wall-mounting type with fixing pegs, keep it safely.
damages to their property. The meaning of each symbol is as follows. After fully aware of meaning
Fixing pegs may cause injury of user.
of each symbol, read the following cautions.
● Install the product of wall-mounting type carefully not to drop from the wall.
This symbol means that wrong handling or ignorance of matters that this symbol indicates Dropping due to earthquake or tremors may cause injury of user.
may cause serious injury or even death of user. ● When installing the product on the wall, consider the thickness and material of the wall.
Dropping in use may cause injury of user.
This symbol means that wrong handling or ignorance of matters that this symbol indicates
may cause serious injury or property damage of user. Cautions for use
● Do not put heavy thing on the product. Dropping or falling due to heavy things on it may cause injury of user.
This symbol means the matter that user should not do at nay event.
Cautions for repairs and maintenance
This symbol means that user should follow the instructions. ● Clean the dust inside the product regularly. Failure to clean the dust for long time may cause fire.
For inspection and cleaning of the inside of product, please contact your local sales agent.
This symbol means that contents (high voltage, electric shock, warnings, etc.) to which user
● When putting your hands into the inside of equipment, be sure that plug is already detached form an outlet or
should pay attention are included.
circuit-breaker is turned off.

This symbol means that a certain action is not permitted. Specific points not permitted are ● Be careful not to expose the product to benzene, thinner or hot water.
depicted around this symbol (for example, in the left drawing, disassembly is not permitted.). ● Do not expose detergent directly to the product in a way of spraying, etc.

● Moving equipment, be sure that the plug is detached from an outlet.

This symbol means instructions or is used to force user to do a certain action. Specific
● For equipment whose cables are connected to terminals, please contact your local sales agent or qualified electrician.
instructions are depicted on the drawing (for example, the left drawing instructs user to detach
power plug from an outlet). ● When replacing old fuse with new one, do not directly touch it with bare hands.
Use insulated tools or contact A/S center.

2 3
 Warnings Warnings

Cautions for use Cautions for use

● Do not install the product at bathroom or at the place near a washing machine, or at other humid places. ● This product is not for perfect security solution.
It may cause fire or electric shock. ● Do not handle the equipment with wet hand, which may cause electric shock.
● Do not install the product at the place near a dresser, humidifier or heater. Also avoid the place exposed to spark, heat or ● Do not place wet or metallic materials on equipment. Water leakage or intrusion of metallic materials may cause fire and
humidity. All of them may cause fire and electric shock. electric shock.
● Do not install the product at the place exposed to dust, metals and harmful gas such as hydrogen sulfide gas. ● Do not block the ventilating opening of equipment or put alien substances into it, which may cause fire and electric shock.
All of which may cause fire and electric shock. ● Do not use battery that is not designated or mix new battery with old ones. Insert batteries to fit their polarity.
● Do not install the product at the place exposed to water and chemicals. This may cause fire and electric shock. Explosion or leakage of battery may cause fire and injury of user.
● Do not scratch, break or arbitrarily process power cable, which may cause fire and electric shock. Putting a heavy thing on ● When visitor's image or voice is not displayed on screen or not sounded from speaker, please check his/her identity before
a cable, heating it or pulling it, may cause impairment on it. opening the door and contact our A/S center.
● Do not place power cable at the place near heating equipment. It may cause damage of cable's clothing material, which ● Do not use equipment when lighting is expected or strokes. It may cause fire and electric shock.
results in fire and electric shock. When detaching plug from an outlet, do not pull power cable. ● Thie product is cannot be used for security.
● Damages on power cable may cause fire and electric shock. When detaching plug from an outlet, please hold the plug ● Do not open rear cover, cabinet and cover of equipment.
tightly. It may cause electric shock.
● Do not detach plug from an outlet with wet hand. It may cause electric shock.
● Do not modify power cable or pull it with excessive strength, which may cause fire and electric shock.
● When using the existing wiring, be sure of the suitability of it to the product and install the product. ● Do not modify equipment. It may cause fire and electric shock.
Failure to this caution may cause fire. ● Call signal may cause damage on user's hearing ability.
● When moving equipment, be sure that plug is detached from an outlet and communication cable is disconnected.
Damage on cables may cause fire. Cautions for abnormality
● When power cable is broken (exposure of core or short-circuit), do not fail to replace broken cable with new one.
● Voltage other than prescribed rated voltage is not permitted, which cause fire and electric shock.
Failure to replace broken power cable may cause fire and electric shock.
● Do not use power terminal of product's main body in other equipment than prescribed ones.
● When detecting any abnormalities in equipment (communication is not available, images do not be displayed on screen,
It may cause fire and short- circuit.
calling is not available, or abnormal sound is heard), immediately detach plug from an outlet, or turn off circuit breaker or
● In wiring work, use the designated wiring materials. detach batteries from equipment (in case that equipment has no plug) before requesting repairs to sales agent or A/S
Wiring work using other materials than designated ones may cause fire. center. Keeping connection to power supply may cause fire and electric shock.
● When alien substances go into equipment, immediately detach plug from an outlet, or turn off circuit breaker or detach
● The equipment without waterproof marking should not be installed at the place water leaks.
batteries from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center.
It may cause electric shock and short circuit.
● In the case of smoke or smell of unknown origin from equipment, keeping use it may cause fire and electric shock. Detach
● When working, be sure that power is disconnected. Failure to disconnect power may cause electric shock.
plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) and
● Be sure that the power cable is connected and earths according to designated method. be sure to check no more smoke or smell from equipment before requesting repair to sales agent or A/S center. Since
Failure to connection and earth may cause fire. personal repairing work by user may serious accidents. In any case, do not repair equipment with your own hand.
● When dropping equipment or breaking its cabinet, detach plug from an outlet, or turn off circuit breaker or detach batteries
● Do not connect power to other terminals than designated ones.
from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center.
It may cause fire and electric shock.
Keeping use equipment may cause fire and electric shock.
● When building a system with the product, do not connect the product to other equipment than designated one. ● Avoid direct exposure to sunlight and store equipment at the place free from dust and high temperature as you can. High
It may cause fire. temperature of equipment may cause fire and electric shock.
● When installing A/C switch, do work after removing the substance that may cause short circuit or electric shock.
● Before installing or providing A/S service, be sure that the power is disconnected.

4 5
 Installation Components
Main body Concealed box Adaptor "L" Wrench
Common gate camera Installation

Concealed
box I-Button key (Option) Sun visor (Option)
Main body

Screws
Screw Wrench screw 2EA

Wrench 8 pin connector between The number of 8pin/4pin/2pin connector

common gate camera & household monitor depends on each model as below.
1. White(VIDEO) KVL-C302i : 2 house - 8pin 1pcs.
2. Red(VOICE) 1 KVL-C303i : 3 house - 8pin 1pcs. & 4pin 1pcs.
2
3. Yellow(GND) 3
KVL-C304i : 4 house - 8pin 2pcs.
Screw 4. Blue(VCC) 4 KVL-TC306i : 6 house - 8pin 2pcs. & 4pin 2pcs.
5
5. White(VIDEO) 6
KVL-TC308i : 8 house - 8pin 4pcs.
6. Red(VOICE) 7 KEL-312 : 12 house - 8pin 6pcs.
8
7. Yellow(GND) KEL-T324 : 24 house - 8pin 12pcs.
8. Blue(VCC)

Standard height for installation Caution of camera installation 4 pin connector between
Common gate camera common gate camera & household monitor
Center
of Lens 1. White(VIDEO)
500mm
lens 1
2. Red(VOICE) 2
1,675

3
3. Yellow(GND) 4
1,500

500mm
4. Blue(VCC)
1,325

2pin connector between 3pin connector between

500
Avoid installing camera exposed to direct ray of light common gate camera & door opener lcommon gate camera & door opener
Standard installation height of common gate
(and sun). 1. Black : GND 1 1. Yellow : Common
camera is 1,400~1,450mm from floor to the 2 1
Beware backlight and darkness of visitor's face, which 2. Red : +12V 2. Brown : Normal close 2
bottom of flush mounting box. 3
makes identification difficult. 3. Black : Normal open
In case that the installation height of common
Avoid installing camera in places such as the following
gate camera is out of the range (min.1,250mm~
picture.
1,550mm), it's hard to get proper image, so be Power input connector between Extension connector between
(1) Place illuminating sky as background
careful about the installation height of common
(2) Place with white wall reflecting direct ray of light
common gate camera & adaptor common gate camera & extension unit
gate camera.
(3) Place with direct ray of light 1. GND
2. N.C
※ Keep away from devices generating strong magnetic field (TV,speaker, etc.) (Picture can be disturbed or blurred and
breakdown can result) 3. VCC
※ According to outside environment, you may view the images somewhat unclear.
However, they do not result from any defect or trouble of the product.
6 7
 Name of Each Part Button & Wiring Information

KVL-TC308i KEL-T324 KVL-TC308i ■ COMMON GATE CAMERA

KVL-C302i KVL-C303i KVL-C304i KVL-TC306i KVL-TC308i
1 2 House 3 House 4 House 6 House 8 House

2
3

8 7 8
5 6 6 5 6 5 6

4 4 4 3 4 3 4

2 2 2 1 2 1 2
6

7 8

KVL-TC308i
NO. Name
1 C-Mic
■ EXTENSION UNIT ■ KVL series to KEL series wiring
2 Camera lens
9 3 White LED KEL-312 KEL-T324
4 Speaker 12 House 24 House
KVL series KEL series
10 5 I-Button probe
6 Name indicator-shows house information
11 7 Call button
12 8 House connection terminals
9 Camera angle adjustment by manual
10 Adjust the audio switch
11 Terminal for door opener
12 Power input terminal
13 Power & DATA
14 GND

I-Button Key
13 ※ connect to
extension
unit
14 (KEL series)

8 9
 Wiring Information Wiring Connection

A. Adjust audio

Button 5 House

KCV-801R

KCV-W354

Button 3 House
A

KCV-A374
Button 7 House
C D B
: Common gate camera → Monitor audio volume

Button 1 House
Using a screwdriver, increase(+) or decrease(-) the
volume from the Common gate camera to the house
E : Monitor → Common gate camera audio volume

KVM-301
Using a screwdriver, increase(+) or decrease(-) the
volume from the house to the Common gate camera

B. POWER INPUT TERMINAL : DC 12V

7
5

3
1
Additional power supply
should be used

GND
N.C
DC+12V/1.5A

C. Terminal for door opener 1 D. Terminal for door opener 2 E. House connection
(Extra adaptor not used) (Extra adaptor is needed) Terminals consist of
Normal opne Normal close 8pin wafer
1. WHITE : VIDEO
Yellow : Yellow : 2. RED : VOICE
Common Common
RED : Black : GND
3. YELLOW : GND

8
6

4
2
POWER 4. BLUE : VCC
DC+12V Black : Brown : 5. WHITE : VIDEO

Button 2 House
300mA DOOR Normal Normal

Button 8 House
open close 6. RED : VOICE
RELEASE
Door Door 7. YELLOW : GND

KCV-802R
DC+12V DC DC
relese relese
300mA 8. BLUE : VCC

KVM-301
adaptor adaptor

Because the common gate camera Door opener 2 is output in N.O / N.C and is
supplies the door opener power, used in connection in compliance with door
12V 300mA, it is not necessary to

1
2
3
4
5
6
7
8
release specification.
install an extra door opener adaptor.

3. YELLOW : GND

7. YELLOW : GND
1. WHITE : VIDEO

5. WHITE : VIDEO

KCV-W354
2. RED : VOICE

6. RED : VOICE
4. BLUE : VCC

8. BLUE : VCC
※ Connection specification of opening/closing device of the above C, D door is not

Button 4 House
operated in individual motion. You have to use by selecting one between two specifications.

Button 6 House

KCV-801R
Common gate camera to monitor 4pin port wiring
upto 50m : CAT5 Cable
upto 80m : TIV 0.6mm(0.3mm²) Cable
upto 100m : TIV 0.8mm(0.5mm²) Cable
upto 150m : TIV 1.0mm(0.8mm²) Cable
10 11
 Operation Explanation I-BUTTON Registration and Deletion
■ Communication with house monitor ※ TACT SWITCH Location
1. When the visitor presses the call button for certain house on the common gate camera,
the certain house monitor gets call signal.
2. In case of hanging up the hand-set or pressing talk button, the conversation is available.
3. When finishing talk, put the hand-set onto the HOOK BAR or press talk button once again.

■ Common gate camera from house monitor

1. During conversation with household monitor, if the door open button on the monitor is pressed,
the common gate is released, in case the door opener is equiped.
Disassemble
2. Spec of door opener using without power supply : DC 12V / 300mA. back case of
3. In order to connect the door opener to the 2 wire connection (non polarity) on the main body
common gate camera, you should use KVM-301, KCV-801, KCV-802, KCV-354 monitor only.
1
■ Common gate open using I-BUTTON KEY 2
1. I-BUTTON KEY registered shall contact on I-BUTTON PROBE.
2. Together with transmission of opening buzzer sound of common main entrance door,
I-BUTTON LED is lit and common main entrance is opened/closed. ①TACT SWICH ②DC POWER
TERMINAL

TACT SWICH is necessary to initialize the Common gate camera and to set door opening time.
I-BUTTON Registration and Deletion ※Only when the power is connected to the Terminal ②, TACT SWICH is available.

■ First registration method of I-BUTTON KEY ■ Deletion method 1 of the entire I-BUTTON KEY: Not revealed
1. Call household device connected to the common gate camera. 1. TACT SWITCH of I-BUTTON PBA is pushed 4 times within 2 seconds.
2. Connect call between called household device and common gate camera. 2. During 2 seconds, total deletion buzzer sound is transmitted and total KEY information is deleted to
3. I-BUTTON KEY is contacted on I-BUTTON PROBE for 5 seconds. be changed as the initial status.
4. As it is recognized as unregistered I-BUTTON KEY, error sound occurs 5 times consecutively.
5. For 5 seconds, mode entry status is notified in sound. ■ Deletion method 2 of the entire I-BUTTON KEY: Not revealed
(Input waiting status notification sound is generated for 10 seconds.)
1. Two of registered I-BUTTON KEYs are prepared.
6. Door opening button is pushed on household device under calling.
2. After calling connected household devices, calls are connected.
(It is registered after recognizing household door opening button.)
3. Under calling status, two KEYs are contacted to I-BUTTON PROBE 4 times in turn during 4 seconds.
7. Buzzer sound advising registration of I-BUTTON KEY after the registration is transmitted.
4. For 5 seconds, it is entered into mode entry status and buzzer sound is transmitted.
5. For 10 seconds, input waiting status notification buzzer sound is transmitted and within 10 seconds,
■ Additional registration method of I-BUTTON KEY
door opening button of household device connected to calling is pushed.
1. Registered I-BUTTON KEY is contacted to I-BUTTON PROBE for 5 seconds. 6. For 2 seconds, total deletion notification sound is generated and stored KEY information is deleted.
2. After generation of recognition sound of I-BUTTON KEY, common main entrance door is
opened/closed 1 time for the first time. ■ Set door opening time
3. I-BUTTON KEY to register additionally after maintaining contact for 5 seconds is contacted to
1. Under waiting status, TACT SWITCH within I-BUTTON PBA is pushed for 4 seconds.
I-BUTTON PROBE.
2. Currently set door opening time buzzer sound is generated for 0.5 seconds.
4. When I-BUTTON KEY is registered, registration sound is transmitted.
3. Once internal PCB button is pushed one time, together with buzzer sound, door opening time is
* In case additionally registering I-BUTTON KEY is contacted to I-BUTTON PROBE within 10 seconds
increased per 1 second.
under the status of registration, it is registered additionally and registration sound is transmitted.
* Do-1 second, Re-2 seconds, Mi-3 seconds, Pa-4 seconds (Basic values), Sol-5 seconds,
(When10 seconds elapse, completion sound becomes in a status of waiting after transmission.)
La-6 seconds, Si-7 seconds, Do-8 seconds (Maximum)

12 13
 Explanation of I-BUTTON Specification
■ I-BUTTON KEY maximum registration quantity
1. Using EEPROM, maximum up to 1022 are registered.
2. it is impossible to store more than 1022 units and when storage capacity is exceeded, buzzer sound
is transmitted for 4 seconds.
* The same I-BUTTON KEY can store and motion but maintains the existing DATA.

Product Specifications

Specifications KVL series / KEL series

Input power DC+12V(Stand by : 0.5W, Operating : 4.5W)
Communication method Hands free method (two way)
Calls/images maintains for 30 ±3 seconds after call
Run time for call / image Communication with house maintains for 3 minutes ±5 seconds
(This time length depends on each model of house monitor)
Exterior material and color METAL ( Zn, Al ) / SILVER
Dimensions 125(W) X 290(H) X 48.4(D)mm
Guaranteed operating -10°C ~ 50°C
Minimum illumination 0.1 Lux (When White LED is turned on)
Camera angle Diagonal 81°(angle adjustable)

■ This product is a Common gate camera connected to 4 wire type products.

It is possible to connect models described in the following.
※ Compatible products
① SECURITY B/W VIDEO PHONE : KVM-301/D301
② SECURITY COLOR VIDEO PHONE : KCV-801/D801, KCV-801R/D801R, KCV-802R/D802R
③ HANDFREE VIDEO PHONE : KCV-W354/DW354, KCV-A374

■ EXTENSION UNIT cannot be used without Common gate camera.