Unit Installation

Overview

Installation Overview
3
INSTALLATION ORDER

 Page 6 
 Indoor Unit Installation
4

Indoor Unit
Installation
Safety Precautions

WARNING CAUTION
• Install the indoor and outdoor units, cables and
• Securely install the indoor unit on a structure that
wires at least 1m from televisions or radios
can sustain its weight. If the structure is too weak
to prevent static or image distortion. Depending
the unit may fall causing personal injury, unit and
on the appliances, a 1m distance may not be
property damage or death.
• If the indoor unit is installed on a metal part of the
building, it must be electrically grounded.

 Page 7 
Indoor Unit Installation
4

 Page 8 
Indoor Unit Installation
4

 Page 9 
 Indoor Unit Installation
4

 Page 10 
 Outdoor Unit Installation
5
Outdoor Unit Installation Instructions

Outdoor Unit
Step 1: Select installation location.  If the location is exposed to strong winds the unit

Installation
The outdoor unit should be installed in the location that must be placed against the wall to shelter it from
meets the following requirements: the wind.
 Place the outdoor unit as close to the indoor unit as
possible.
 Ensure that there is enough room for installation and
maintenance.
Strong wind
 The air inlet and outlet must not be obstructed or
exposed to strong wind.
 Ensure the location of the unit will not be subject to
Strong wind
snowdrifts, accumulation of leaves or other seasonal
debris. If possible, provide an awning for the unit. Fig. 5.1
Ensure the awning does not obstruct airflow.
 The installation area must be dry and well ventilated.
 There must be enough room to install the connecting
pipes and cables and to access them for maintenance.

 The pipe length between the outdoor and indoor unit

may not exceed the maximum allowable pipe length.

Strong wind

Fig. 5.2

Step 2: Install outdoor unit.

Fix the outdoor unit with anchor bolts (M10)

>60cm
CAUTION
• Be sure to remove any obstacles that
Fix with bolts may block air circulation.
• Make sure you refer to Length
Specifications to ensure there is
enough room for installation and
maintenance.

Fig. 5.3

 Page 11 
 Outdoor Unit Installation Instructions

For MOBA03-09HFN1-QRD0GW, MOBA03-12HFN1-QRD0GW

779 W3
Outdoor Unit
Installation

487 W1
300 D 770 W
70 W2
25 B1

D2 D3
D1

61.5 A2
H1

H2

12 A1

NOTE

Since the gravity center of the unit is not at its physical center, so please be careful when lifting it with a sling.
Never hold the inlet of the outdoor unit to prevent it from deforming.
Do not touch the fan with hands or other objects.
Do not lean it more than 45, and do not lay it sidelong.
Make concrete foundation according to the specifications of the outdoor units.
Fasten the feet of this unit with bolts firmly to prevent it from collapsing in case of earthquake or strong wind.

 Page 12 
 NOTE: The minimum distance between the outdoor Notes On Drilling Hole In Wall
unit and walls described in the installation guide does
not apply to airtight rooms. Be sure to keep the unit
unobstructed in at least two of the three directions (M,
N, P) (See Fig. 5.10) You must drill a hole in the wall for the refrigerant piping,
and the signal cable that will connect the indoor and
outdoor units.
above

Outdoor Unit
Installation
1. Determine the location of the wall hole based on the
60cm

cm
location of the outdoor unit.
30
2. Using a 65-mm core drill, drill a hole in the wall.
30cm
on le
ft

60cm
NOTE: When drilling the wall hole, make sure
on r
ight to avoid wires, plumbing, and other sensitive
m t components.
0c ron
20 in f

3. Place the protective wall cuff in the hole. This

Fig. 5.10 protects the edges of the hole and will help seal it
when you finish the installation process.

Drain Joint Installation

Before bolting the outdoor unit in place, you must install
the drain joint at the bottom of the unit. (See Fig. 5.11)
1. Fit the rubber seal on the end of the drain joint that
will connect to the outdoor unit.
2. Insert the drain joint into the hole in the base pan of
the unit.
3. Rotate the drain joint 90° until it clicks in place
facing the front of the unit. Base pan hole of
outdoor unit
4. Connect a drain hose extension (not included) to
the drain joint to redirect water from the unit during Seal
heating mode. Seal

NOTE: Make sure the water drains to a safe location

where it will not cause water damage or a slipping
hazard. Drain joint

(A) (B)

Fig. 5.11

 Page 15 
 Drainpipe Installation
6

 Page 16
 Refrigerant Piping Connection
7
WARNING Refrigerant Piping Connection Instructions
• All field piping must be completed by a licensed
technician and must comply with the local and Step1: Cut pipes
national regulations. When preparing refrigerant pipes, take extra care
• When the air conditioner is installed in a small to cut and flare them properly. This will ensure
room, measures must be taken to prevent the efficient operation and minimize the need for future
refrigerant concentration in the room from maintenance.
exceeding the safety limit in the event of 1. Measure the distance between the indoor and
refrigerant leakage. If the refrigerant leaks and outdoor units.
its concentration exceeds its proper limit, hazards 2. Using a pipe cutter, cut the pipe a little longer than
due to lack of oxygen may result. the measured distance.
• When installing the refrigeration system, ensure
that air, dust, moisture or foreign substances do
not enter the refrigerant circuit. Contamination
CAUTION
Refrigerant Piping

in the system may cause poor operating capacity,

high pressure in the refrigeration cycle, explosion
Connection

or injury.
An angle of more than 10° may cause malfunction.
• Ventilate the area immediately if there is • DO NOT install the connecting pipe until both
refrigerant leakage during the installation. Leaked indoor and outdoor units have been installed.
refrigerant gas is both toxic and flammable.
Ensure there is no refrigerant leakage after
completing the installation work.

• Insulate both the gas and liquid piping to prevent

water leakage.

Table 7.1: The Maximum Length And Drop Height

Based on Models. (Unit: meters)

Model Length of Maximum drop

piping height Notes On Pipe Length and Elevation
09 25 10
12 25 10 Ensure that the length of the refrigerant pipe, the number
18 30 20
of bends, and the drop height between the indoor and
outdoor units meets the requirements shown in Table 7.1:
24 50 25

 Page 17 
 Refrigerant Piping Connection
7
CAUTION
DO NOT deform pipe while cutting. Be extra careful not
to damage, dent, or deform the pipe while cutting. This
1. After removing burrs from cut pipe, seal the ends
will drastically reduce the heating efficiency of the unit.
with PVC tape to prevent foreign materials from
entering the pipe.
2. Sheath the pipe with insulating material.
3. Place flare nuts on both ends of pipe. Make sure
1. Make sure that the pipe is cut at a perfect 90° they are facing in the right direction, because you
angle. Refer to Fig. 7.2 for examples of bad cuts can’t put them on or change their direction after
flaring. See Fig. 7.4

Flare nut

Refrigerant Piping
90°
Oblique Rough Warped

Connection
Copper pipe

Fig. 7.2 Fig. 7.4

Step 2: Remove burrs.

Burrs can affect the gas-tight seal of refrigerant
piping connection. They must be completely 4. Remove PVC tape from ends of pipe when ready to
removed. perform flaring work.
5. Clamp flare form on the end of the pipe. The end
of the pipe must extend beyond the flare form.
1. Hold the pipe at a downward angle to prevent
burrs from falling into the pipe.
2. Using a reamer or deburring tool, remove all burrs Flare form
from the cut section of the pipe.

Pipe

Reamer

Point down

Pipe

Fig. 7.5
Fig. 7.3
Step 3: Flare pipe ends
Proper flaring is essential to achieve an gas-tight seal

 Page 18 
 6. Place flaring tool onto the form. Step 4: Connect pipes
7. Turn the handle of the flaring tool clockwise until Connect the copper pipes to the indoor unit first, then
the pipe is fully flared. Flare the pipe in accordance connect it to the outdoor unit. You should first connect the
with the dimensions shown in table 7-3. low-pressure pipe, then the high-pressure pipe.
8. Remove the flaring tool and flare form, then inspect 1. When connecting the flare nuts, apply a thin coat
the end of the pipe for cracks and even flaring. of refrigeration oil to the flared ends of the pipes.
2. Align the center of the two pipes that you will
connect.

CAUTION
Check to make sure there is no refrigerant leak after
completing the installation work. If there is a refrigerant
leak, ventilate the area immediately and evacuate Indoor unit tubing Flare nut Pipe
Refrigerant Piping

the system (refer to the Air Evacuation section of this

Connection

manual). Fig. 7.7

3. Tighten the flare nut as tightly as possible by hand.

4. Using a spanner, grip the nut on the unit tubing.
Table 7.3: PIPING EXTENSION BEYOND FLARE FORM
5. While firmly gripping the nut, use a torque wrench
Pipe Tightening Flare dimension (A) Flare shape to tighten the flare nut according to the torque
gauge torque (Unit: mm)
values in table 7-.3.
Min. Max .
14.2-17.2 N.m
1/4 8.3 8.3 90 °± 4
(144-176 kgf.cm)
45 °
32.7-39.9 N.m
±2 NOTE: Use both a spanner and a torque wrench when
3/8 12.4 12.4 A
(333-407 kgf.cm) connecting or disconnecting pipes to/from the unit.
49.5-60.3 N.m R0.4~0.8
1/2 15.4 15.8
(504-616 kgf.cm)
61.8-75.4 N.m
5/8 18.6 19
(630-770 kgf.cm)
Fig. 7.6
97.2-118.6 N.m
3/4 (990-1210 kgf. 22.9 23.3
cm)
109.5-133.7 N.m
7/8 (1117-1364 kgf. 27 27.3
cm)
Fig. 7.8

 Page 19 
 Wiring
8
Follow these instructions to prevent distortion when the
Safety Precautions
compressor starts:
• The unit must be connected to the main outlet.
Normally, the power supply must have a low output
WARNING impedance of 32 ohms.
• Be sure to disconnect the power supply before • No other equipment should be connected to the
working on the unit. same power circuit.
• All electrical wiring must be done according to • The unit’s power information can be found on the
local and national regulations. rating sticker on the product.
• Electrical wiring must be done by a qualified
technician. Improper connections may cause NOTE: The fuse is made of ceramic.
electrical malfunction, injury and fire.
• An independent circuit and single outlet must
be used for this unit. If the
electrical circuit capacity is not enough or there Outdoor Unit Wiring
is a defect in the electrical work, it can lead to
shock, fire, unit and property damage.

• Connect the power cable to the terminals and WARNING

fasten it with a clamp. An insecure connection Before performing any electrical or wiring work, turn off
may cause fire. the main power to the system.
• Make sure that all wiring is done correctly and the
control board cover is properly installed. Failure

Wiring
to do so can cause overheating at the connection
1. Prepare the cable for connection
points, fire, and electrical shock.
• Ensure that main supply connection is made
Cross-section area of power
through a switch that disconnects all poles, with
contact gap of a least 3mm. Rated Current of Nominal Cross-Sectional
Appliance (A) Area (mm²)
6 0.75

6 - 10 1

10 - 16 1.5
CAUTION 16 - 25 2.5
• Connect the outdoor wires before connecting the
25- 32 4
indoor wires.
32 - 45 6
• Make sure you ground the unit. The grounding
wire should be away from gas pipes, water pipes,
lightning rods, telephone or other grounding
wires. Improper grounding may cause electrical
shock.
• DO NOT connect the unit with the power source
until all wiring and piping is completed.
• Make sure that you do not cross your electrical
wiring with your signal wiring, as this can cause
distortion and interference.

 Page 20 
 b. Using wire strippers, strip the rubber jacket from
both ends of signal cable to reveal about 15cm
of the wires inside. Terminal block
Wire cover
c. Strip the insulation from the ends of the wires.
d. Using a wire crimper, crimp u-lugs on the ends of
the wires.
Screw
NOTE: While connecting the wires, please strictly follow Cable clamp
the wiring diagram (found inside the electrical box cover).
2. Remove the electric cover of the outdoor unit.
If there is no cover on the outdoor unit, disassemble
the bolts from the maintenance board and remove the
protection board. (See Fig. 8.1, 8.2)

4. Connect the u-lugs to the terminals.

Cover Match the wire colours/labels with the labels on the
terminal block, and firmly screw the u-lug of each
wire to its corresponding terminal. Refer to the Serial
Screw Number and Wiring Diagram located on the cover of
the electric control box.
Wiring

Fig. 8.1

3. Connect the u-lugs to the terminals

Match the wire colours/labels with the labels on the
terminal block, and firmly screw the u-lug of each wire
to its corresponding terminal.
4. Clamp down the cable with designated cable clamp.
5. Insulate unused wires with electrical tape. Keep them
away from any electrical or metal parts.
6. Reinstall the cover of the electric control box.
Indoor Unit Wiring
Wiring diagram Connective wiring diagram
1. Prepare the cable for connection
Fig. 8.4
a. Using wire strippers, strip the rubber jacket from
both ends of signal cable to reveal about 15cm
of the wires inside. CAUTION
b. Strip the insulation from the ends of the wires. • While connecting the wires, please strictly follow
c. Using wire crimper, crimp the u-lugs to the ends of the wiring diagram.
the wires. • The refrigerant circuit can become very hot. Keep
the interconnection cable away from the copper
2. Open the front panel of the indoor unit. Using a tube.
screwdriver, remove the cover of the electric control box
5. Clamp down cable with the designated cable clamp to
on your indoor unit.
secure it in place. The cable should not be loose, and
3. Thread the power cable and the signal cable through should not pull on the u-lugs.
the wire outlet.
6. Reinstall the electric box cover and the front panel of
the indoor unit.

 Page 21 
 Pressure Test Instructions
9
Systems are pressure tested to ensure they are:

Safe – for this test a pressure above the system’s maximum allowable
pressure (PSi) is used
Leak tight – this test is at PSi.

Pressure testing is hazardous and should be carried out carefully:

The nitrogen used for pressure testing is an asphyxiant, so the area around
the system should be well-ventilated
High pressures are used, so all non-essential personal should be evacuated
from the area
Anyone carrying out the pressure testing should wear safety goggles.

Nitrogen and regulation

Dry (oxygen free) nitrogen (OFN) is used to achieve the pressures required for the
pressure tests because it is inert. You must never use oxygen for pressure testing -
pure oxygen at high pressure reacts violently with oil and will explode.

The pressure tests

Increase the pressure to approximately 5 bar g and check for leaks using leak
detection spray at this pressure initially – many leaks will be identified at this
pressure so you will not waste nitrogen and time. It is also safer to find leaks at a
lower pressure than the final test pressures.

Increase the pressure slowly to the strength test pressure and hold it for 15
minutes. Under the Pressure Equipment Regulation this strength test might need
to be witnessed by a notified body.

Using the nitrogen regulator

1. Ensure the regulator is

closed (wound fully anti
clockwise);
2. Open the cylinder valve
3. Slowly open the regulator
to the pressure required.

Do not use a regulator with an

output pressure much higher

 Page 24 