Parameter Settings Report (Program) 26/11/2018 3:58:25 p. m.

Program (Drive Selected / Connected):

Drive Type / Model: iQpump Micro CIMR-PW2V0040***
Software: 10100

Project:
User:

Information

Network Configuration

H5-01=01 | H5-01=02 |

Note: Each iQpump Micro drive must have its own unique serial address (H5-01)
Use shielded communication cables to connect all iQpump Micro drives.
Connect all iQpump Micro drives according to the wiring shown above. (R+ to S+ and R- to S-)

DriveWizard iQpump for Windows (C) by Yaskawa America, Inc. 1/15

 26/11/2018 3:58:25 p. m.
iQpump Micro Network Quick Start Instructions:
Note: Follow these instructions to setup your iQpump Micro network manually.

Step 1:
Wire all iQpump Micro drives according to the network configuration diagram (R+/R-/S+/S-) as shown on the first page of
this report.
Use shielded communication cables to connect all iQpump Micro drives.
Step 2:
Set Serial communication address parameter H5-01 for each iQpump Micro drive as shown on the first page of this report.

Step 3:
Program each iQpump controller parameter P9-25 (Highest Node Address) to: X
Step 4:
Program each iQpump controller parameter P1-01 (Pump Mode) to 3:
Step 5:
Recycle power to ALL iQpump Micro drives on the network.
Step 6:
Check U9-02 and verify that :
- No iQpump Micro drives have a value of "- 0"
- All iQpump Micro drives receive valid data and U9-02 changes regularly.
- At least one iQpump Micro drive has the unit , while the rest have the unit .

If there is an iQpump Micro drive with "- 0":

- Check communication wiring as shown on first page of this report
- Verify the serial communication address (H5-01) as shown on first page of this report
- Confirm P9-25 and P9-27 settings on all drives. P9-25 should be set to the highest H5-01 address and atleast one
iQpump Micro drive should have P9-27 = 0.
- Cycle power to all iQpump Micro drives.
Step 7:
Program each iQpump Micro drive on the network using the parameter list shown on the next page.

Step 8:
Verify pump rotation using hand mode operation. If rotation is incorrect, power-down the iQpump Micro drive and wait 5
minutes. Using Safety precaution, swap any two of the three output leads to the motor (U/T1, V/T2 and W/T3).
After the wiring change recheck motor direction using hand operation.

Step 9:
Ready to run pump system.

Digital operator control:

- Press Auto button on ALL the digital operators to initiate Auto mode operation.
Contact / Terminal Control:
- Close run contact on terminals on all iQpump controllers to initiate Auto mode operation.
 Default
Parameter Value Information Setting

A1-01 Access level 2 Advanced Level 2

A1-02 Control method 0 V/f control 0
A1-03 Initialize Parameters 0 No Initialization 0
A1-04 Enter password 0 0
A1-05 Select password 0 0
A1-06 Application Preset 0 Pressure Control 0
A1-07 DWEZ Function Selection 0 Disabled 0

A2-01 User parameter 1 E2-01 Motor rated current E2-01

A2-02 User parameter 2 E2-04 Number of motor poles E2-04
A2-03 User parameter 3 P1-03 Feedback Scaling P1-03
A2-04 User parameter 4 Q1-01 PID Controller Setpoint 1 Q1-01
A2-05 User parameter 5 P1-04 Start / Draw Down Level P1-04
A2-06 User parameter 6 P1-06 Minimum Pump Speed P1-06
A2-07 User parameter 7 P4-10 AUTO Mode Operator Run Power Down Storage P4-10
A2-08 User parameter 8 P5-04 HAND Key Function Selection P5-04
A2-09 User parameter 9 Not Mapped -N/M-
A2-10 User parameter 10 Not Mapped -N/M-
A2-11 User parameter 11 Not Mapped -N/M-
A2-12 User parameter 12 Not Mapped -N/M-
A2-13 User parameter 13 Not Mapped -N/M-
A2-14 User parameter 14 Not Mapped -N/M-
A2-15 User parameter 15 Not Mapped -N/M-
A2-16 User parameter 16 Not Mapped -N/M-
A2-17 User parameter 17 Not Mapped -N/M-
A2-18 User parameter 18 Not Mapped -N/M-
A2-19 User parameter 19 Not Mapped -N/M-
A2-20 User parameter 20 Not Mapped -N/M-
A2-21 User parameter 21 Not Mapped -N/M-
A2-22 User parameter 22 Not Mapped -N/M-
A2-23 User parameter 23 Not Mapped -N/M-
A2-24 User parameter 24 Not Mapped -N/M-
A2-25 User parameter 25 Not Mapped -N/M-
A2-26 User parameter 26 Not Mapped -N/M-
A2-27 User parameter 27 Not Mapped -N/M-
A2-28 User parameter 28 Not Mapped -N/M-
A2-29 User parameter 29 Not Mapped -N/M-
A2-30 User parameter 30 Not Mapped -N/M-
A2-31 User parameter 31 Not Mapped -N/M-
A2-32 User parameter 32 Not Mapped -N/M-
A2-33 User parameter Automatic registration 0 Automatic registration is unavailable(Totally user setting from 0
Function A2-01 toA2-32)

b1-01 Reference selection 0 Digital operator 0

1 Control circuit terminal 0
0 Deceleration to stop 1
b1-04 Reverse operation 1 Reverse disabled 1

3/15
 Default
Parameter Value Information Setting
b1-07 Run Command Retention when Source is 0 Require Cycle 0
Changed
1 Enabled - Run command accepted in all menus (except when 0
b1-02 = 0).
b1-11 Run Delay at Stop 0,0 sec 0,0 sec
b1-12 Run Delay Memory Selection 2 Running & Stop 2
1 Exchange the Phase turn (without PG only) 0
b1-15 Reference Selection in Local case 0 Digital Operator 0
b1-16 Operation method selection in Local case 0 Digital Operator 0
b1-17 Operation permission with power ON/OFF 1 Permission 1

b2-01 DC injection start frequency 0,5 Hz 0,5 Hz

b2-02 DC injection current 50 % 50 %
b2-03 DC injection time at start 0,00 sec 0,00 sec
b2-04 DC injection time at stop 0,50 sec 0,50 sec

b3-01 Speed search at start 0 Disabled 0

b3-02 Speed search current 120 % 120 %
b3-03 Speed search deceleration time 2,0 sec 2,0 sec
b3-05 Search wait time 0,2 sec 0,2 sec
b3-06 Output current 0,5 A 0,5 A
b3-08 ACR Gain for Speed Search 0,50 0,50
b3-10 Speed Search Detection Compensation Gain 1,05 1,05
b3-14 Bidirectional search selection 0 Disabled 0
b3-17 Retry current level 150 % 150 %
b3-18 Retry detection time 0,10 sec 0,10 sec
b3-19 Retry count 3 3
b3-24 Speed search method selection 0 Current detection type 0
b3-25 Speed search retry interval time 0,5 sec 0,5 sec

b4-01 Delay-ON timer 0,0 sec 0,0 sec

b4-02 Delay-OFF timer 0,0 sec 0,0 sec

b5-01 PID control mode selection 1 Enabled 1

2,30 2,00
1,3 sec 3,0 sec
b5-04 PID I limit 100,0 % 100,0 %
b5-05 PID D time 0,00 sec 0,00 sec
b5-06 PID limit 100,0 % 100,0 %
b5-07 PID offset adjustment 0,0 % 0,0 %
1,00 sec 0,00 sec
b5-09 Output level selection 0 Direct Acting 0
b5-10 PID output gain 1,00 1,00
b5-11 PID output reverse selection 0 0 limit when PID putput is negative 0
b5-12 Feedback Loss 4 to 20mA Detection 2 Fault 2
Selection
b5-13 Feedback Loss Goto Frequency 0,0 Hz 0,0 Hz
b5-14 Feedback Loss of Prime Level 0,0 A 0,0 A
b5-15 Feedback Loss Go To Frequency Time Out 0 sec 0 sec
b5-16 Feedback Loss Start Delay 0,0 sec 0,0 sec

4/15
 Default
Parameter Value Information Setting
b5-17 Accel/Decel time for PID reference 0 sec 0 sec
b5-32 Integrator Ramp Limit 0,0 Hz 0,0 Hz
b5-34 PID Output Lower Limit 0,0 % 0,0 %
b5-35 PID Input Limit 1000,0 % 1000,0 %
b5-39 PID Setpoint Set up/Display Number of 1 One decimal place 1
decimals
b5-40 PID Fref monitor Selection 0 Fref Monitor with PID 0
b5-47 PID Output Reverse Selection2 1 Reverses when PID output is negative. 1

b6-01 Dwell frequency at start 0,0 Hz 0,0 Hz

b6-02 Dwell time at start 0,0 sec 0,0 sec
b6-03 Dwell frequency at stop 0,0 Hz 0,0 Hz
b6-04 Dwell time at stop 0,0 sec 0,0 sec

3,0 sec 20,0 sec

5,0 sec 10,0 sec
C1-03 Acceleration time 2 10,0 sec 10,0 sec
C1-04 Deceleration time 2 10,0 sec 10,0 sec
C1-09 Emergency stop time 10,0 sec 10,0 sec
C1-10 Accel/Decel time setting unit 1 0.1-second units 1
C1-11 Accel/Decel switching frequency 0,0 Hz 0,0 Hz
C1-14 Picking up speed and slowing down rate 0,0 Hz 0,0 Hz
setting standard frequency

C2-01 S-curve acceleration at start 0,20 sec 0,20 sec

C2-02 S-curve acceleration at end 0,20 sec 0,20 sec
C2-03 S-curve deceleration at start 0,20 sec 0,20 sec
C2-04 S-curve deceleration at end 0,00 sec 0,00 sec

C3-01 Slip compensation gain 0,0 0,0

C3-02 Slip compensation time 2000 ms 2000 ms
C3-03 Slip compensation limit 200 % 200 %
C3-04 Slip compensation regeneration 0 Disabled 0

C4-01 Torque compensation gain 1,00 1,00

C4-02 Torque compensation time 200 ms 200 ms

C6-02 Carrier frequency selection 07 Swing-PWM1 07

d1-01 Frequency reference 1 0,00 Hz 0,00 Hz

d1-02 Frequency reference 2 0,00 Hz 0,00 Hz
d1-03 Frequency reference 3 0,00 Hz 0,00 Hz
d1-04 Frequency reference 4 0,00 Hz 0,00 Hz
d1-05 Frequency reference 5 0,00 Hz 0,00 Hz
d1-06 Frequency reference 6 0,00 Hz 0,00 Hz
d1-07 Frequency reference 7 0,00 Hz 0,00 Hz
d1-08 Frequency reference 8 0,00 Hz 0,00 Hz
d1-09 Frequency reference 9 0,00 Hz 0,00 Hz
d1-10 Frequency reference 10 0,00 Hz 0,00 Hz

5/15
 Default
Parameter Value Information Setting
d1-11 Frequency reference 11 0,00 Hz 0,00 Hz
d1-12 Frequency reference 12 0,00 Hz 0,00 Hz
d1-13 Frequency reference 13 0,00 Hz 0,00 Hz
d1-14 Frequency reference 14 0,00 Hz 0,00 Hz
d1-15 Frequency reference 15 0,00 Hz 0,00 Hz
d1-16 Frequency reference 16 0,00 Hz 0,00 Hz
d1-17 Jog frequency reference 6,00 Hz 6,00 Hz

d2-01 Frequency reference upper limit 100,0 % 100,0 %

d2-02 Frequency reference lower limit 0,0 % 0,0 %
d2-03 Master speed reference lower limit 0,0 % 0,0 %

d3-01 Jump frequency 1 0,0 Hz 0,0 Hz

d3-02 Jump frequency 2 0,0 Hz 0,0 Hz
d3-03 Jump frequency 3 0,0 Hz 0,0 Hz
d3-04 Jump frequency width 1,0 Hz 1,0 Hz

d4-01 MOP reference memory 0 Disabled 0

d4-03 Frequency reference bias steps(up/down2) 0,00 Hz 0,00 Hz
d4-04 Accel/Decel rate selection(up/down2) 0 Bias value Accel/Decel at the rate of current selected 0
Accel/Decel time
d4-05 Bias mode selection(up/down2) 0 Hold bias value while both of UP/DOWN command are 0
ON/OFF
d4-06 Bias value(up/down2) 0,0 % 0,0 %
d4-07 Analog change limit 1,0 % 1,0 %
d4-08 Frequency Reference Bias Upper Limit 100,0 % 100,0 %
(up/down2)
d4-09 Frequency Reference Bias Lower Limit 0,0 % 0,0 %
(up/down2)
d4-10 Up/Down Frequency Reference Limit 0 The lower limit is determined by d2-02 or analog input 0
Selection (H3-02/10 = 0)

E1-01 Input voltage setting 230 VAC 230 VAC

E1-03 V/F pattern selection 0F User-defined V/f pattern 0F
E1-04 Max. output frequency 60,0 Hz 60,0 Hz
E1-05 Max. voltage 230,0 VAC 230,0 VAC
E1-06 Base frequency 60,0 Hz 60,0 Hz
E1-07 Mid output frequency 3,0 Hz 3,0 Hz
E1-08 Mid output frequency voltage 16,1 VAC 16,1 VAC
E1-09 Min. output frequency 1,5 Hz 1,5 Hz
E1-10 Min. output frequency voltage 8,1 VAC 8,1 VAC
E1-11 Mid output frequency 2 0,0 Hz 0,0 Hz
E1-12 Mid output frequency voltage 2 0,0 VAC 0,0 VAC
E1-13 Base voltage 0,0 VAC 0,0 VAC

E2-01 Motor rated current 39,70 A 39,70 A

E2-02 Motor rated slip 1,70 Hz 1,70 Hz
12,00 A 11,20 A
E2-04 Number of motor poles 2 2
E2-05 Motor line-to-line resistance 0,230 Ohm 0,230 Ohm
E2-06 Motor leak inductance 19,5 % 19,5 %
E2-10 Torque compensation iron loss 245 W 245 W

6/15
 Default
Parameter Value Information Setting
E2-11 Motor rated output 11,00 kW 11,00 kW

F6-01 Operation selection after communications 1 Coast to stop 1

error
F6-02 Selection of External Fault from 0 Always detect 0
Communication Option Board
F6-03 Stopping Method for External Fault from 1 Coast to Stop 1
Communication Option Board
F6-04 BUS error detection delay 2,0 sec 2,0 sec
F6-07 Fref Priority Selection 1 MultiStep Speed is vailable. 1
F6-08 Comm Parameter Initialize Selection 0 Comm Parameters are not initialized due to A1-02. 0
F6-10 Node Address 0 0
F6-11 Communication Speed 0 156 Kbps 0
F6-14 BUS Error Auto Reset 0 Disabled 0
F6-20 M-II Station Address 21 21
F6-21 M-II Frame length 0 32byte mode 0
F6-22 M-II Link Speed 0 10 Mbps 0
F6-23 M-II Mon E register 0000 0000
F6-24 M-II Mon F register 0000 0000
F6-25 M-II WDT error selection 1 Coast to stop 1
F6-26 M-II Number of bUS error detection 2 2
F6-30 Node Address 0 0
F6-31 Clear Mode Selection 0 Resets back to zero. 0
F6-32 ProfibusMap Selection 0 PPO Type 0
F6-35 CanOpen Node Address 0 0
F6-36 Communication Speed 6 500 Kbps 6
F6-40 Node Address 0 0
F6-41 Communication Speed 1 Auto-adjust 1
F6-50 MAC Address 64 64
F6-51 Baud Rate 4 Detect automatically 4
F6-52 PCA Setting 21 21
F6-53 PPA Setting 71 71
F6-54 Idle Mode Fault Detection 0 No Detection 0
F6-56 Speed Scaling 0 0
F6-57 Current Scaling 0 0
F6-58 Torque Scaling 0 0
F6-59 Power Scaling 0 0
F6-60 Voltage Scaling 0 0
F6-61 Time Scaling 0 0
F6-62 Heart Beat 0 0
F6-64 Dynamic Output Assembly 109 Parameter 1 0000 0000
F6-65 Dynamic Output Assembly 109 Parameter 2 0000 0000
F6-66 Dynamic Output Assembly 109 Parameter 3 0000 0000
F6-67 Dynamic Output Assembly 109 Parameter 4 0000 0000
F6-68 Dynamic Input Assembly 159 Parameter 1 0000 0000
F6-69 Dynamic Input Assembly 159 Parameter 2 0000 0000
F6-70 Dynamic Input Assembly 159 Parameter 3 0000 0000
F6-71 Dynamic Input Assembly 159 Parameter 4 0000 0000
F6-72 Node Address 0 0

7/15
 Default
Parameter Value Information Setting
F7-01 IP Address1 192 192
F7-02 IP Address2 168 168
F7-03 IP Address3 1 1
F7-04 IP Address4 20 20
F7-05 Subnet Mask1 255 255
F7-06 Subnet Mask2 255 255
F7-07 Subnet Mask3 255 255
F7-08 Subnet Mask4 0 0
F7-09 Gateway Address1 192 192
F7-10 Gateway Address2 168 168
F7-11 Gateway Address3 1 1
F7-12 Gateway Address4 1 1
F7-13 Address Startup Mode 2 2
F7-14 Duplex Mode Setting 1 Auto Negotiate 1
F7-15 Speed Mode Setting 10 10 Mbps speed setting 10
F7-16 Timeout Value 0 0
F7-17 Speed Scaling 0 0
F7-18 Current Scaling 0 0
F7-19 Torque Scaling 0 0
F7-20 Power Scaling 0 0
F7-21 Voltage Scaling 0 0
F7-22 Time Scaling 0 0
F7-23 Dynamic Output Assembly 116 Parameter 1 0000 0000
F7-24 Dynamic Output Assembly 116 Parameter 2 0000 0000
F7-25 Dynamic Output Assembly 116 Parameter 3 0000 0000
F7-26 Dynamic Output Assembly 116 Parameter 4 0000 0000
F7-27 Dynamic Output Assembly 116 Parameter 5 0000 0000
F7-28 Dynamic Output Assembly 116 Parameter 6 0000 0000
F7-29 Dynamic Output Assembly 116 Parameter 7 0000 0000
F7-30 Dynamic Output Assembly 116 Parameter 8 0000 0000
F7-31 Dynamic Output Assembly 116 Parameter 9 0000 0000
F7-32 Dynamic Output Assembly 116 Parameter 10 0000 0000
F7-33 Dynamic Input Assembly 166 Parameter 1 0000 0000
F7-34 Dynamic Input Assembly 166 Parameter 2 0000 0000
F7-35 Dynamic Input Assembly 166 Parameter 3 0000 0000
F7-36 Dynamic Input Assembly 166 Parameter 4 0000 0000
F7-37 Dynamic Input Assembly 166 Parameter 5 0000 0000
F7-38 Dynamic Input Assembly 166 Parameter 6 0000 0000
F7-39 Dynamic Input Assembly 166 Parameter 7 0000 0000
F7-40 Dynamic Input Assembly 166 Parameter 8 0000 0000
F7-41 Dynamic Input Assembly 166 Parameter 9 0000 0000
F7-42 Dynamic Input Assembly 166 Parameter 10 0000 0000

H1-01 Terminal S1 function selection 40 Forward Run Command 40

H1-02 Terminal S2 function selection 0F Not used(Unused / when use it as a pass-through mode.) 0F
09 External baseblock (N/C) 26
H1-04 Terminal S4 function selection 14 Fault reset 14

8/15
 Default
Parameter Value Information Setting
H1-05 Terminal S5 function selection 8D Multi Setpoint 1 8D
H1-06 Terminal S6 function selection 80 Hand Mode 80
H1-07 Terminal S7 function selection 81 Hand Mode 2 81
H1-21 External Fault 1 Delay Time 0,00 sec 0,00 sec
H1-22 External Fault 2 Delay Time 0,00 sec 0,00 sec
H1-23 External Fault 3 Delay Time 0,00 sec 0,00 sec
H1-24 External Fault 4 Delay Time 0,00 sec 0,00 sec
H1-25 External Fault 5 Delay Time 0,00 sec 0,00 sec
H1-26 External Fault 6 Delay Time 0,00 sec 0,00 sec
H1-27 External Fault 7 Delay Time 0,00 sec 0,00 sec

H2-01 Terminal MA/MB-MC Selection 000E Fault 000E

H2-02 Terminal P1 Selection 0037 During frequency output (ON: During frequency output) 0037
H2-03 Terminal P2 Selection 000E Fault 000E
H2-06 Output unit selection 0 0.1kWh unit 0

H3-01 Terminal A1 Signal Level Selection 0 0 to +10 V 0

H3-02 Terminal A1 Function Selection 20 Hand Frequency Reference 20
H3-03 Terminal A1 Gain Setting 100,0 % 100,0 %
H3-04 Terminal A1 Bias Setting 0,0 % 0,0 %
H3-09 Terminal A2 Signal Level Selection 2 4 to 20 mA 2
H3-10 Terminal A2 Function Selection 0B PID Feedback 1 0B
H3-11 Terminal A2 Gain Setting 100,0 % 100,0 %
H3-12 Terminal A2 Bias Setting 0,0 % 0,0 %
H3-13 Filter Avg time 0,03 sec 0,03 sec
H3-14 Terminal Analog Input Selection(when H1-xx 7 Terminal A1 and A2 Enable 7
= C)
H3-16 A1 Offset 0 0
H3-17 A2 Offset 0 0

H4-01 Multi-Function Analog 1(Analog Terminal 102 Output frequency 102

Monitor Selection)
H4-02 Multi-Function Analog 1(Analog Terminal 100,0 % 100,0 %
Output Gain)
H4-03 Multi-Function Analog 1(Analog Terminal 0,0 % 0,0 %
Output Bias)

02 1F
H5-02 Communication speed selection 3 9600 bps 3
H5-03 Communication parity selection 0 No parity 0
H5-04 Serial fault selection 3 Operation continued 3
H5-05 CE Detection Selection 1 Enabled 1
H5-06 Send wait time 5 ms 5 ms
H5-07 RTS control ON/OFF 1 Enabled 1
H5-09 CE detection time 2,0 sec 2,0 sec
H5-10 Output voltage monitor(Register No.25) unit 0 0.1V unit 0
H5-11 ENTER function selection of transmission 0 A constant is reflected and memorized when ENTER is input. 0
H5-12 Run Command Method Selection 0 FWD/STOP,REV/STOP type 0

H6-01 Pulse train input function selection 0 Frequency reference 0

H6-02 Pulse train input scaling 1440 Hz 1440 Hz

9/15
 Default
Parameter Value Information Setting
H6-03 Pulse train input gain 100,0 % 100,0 %
H6-04 Pulse train input bias 0,0 % 0,0 %
H6-05 Pulse train input filter time 0,10 sec 0,10 sec
H6-06 Pulse train monitor selection 102 Output frequency 102
H6-07 Pulse train monitor scaling 1440 Hz 1440 Hz
H6-08 Pulse Train Min Input Frequency 0,5 Hz 0,5 Hz

L1-01 Motor protection selection 1 General-purpose motor protection 1

L1-02 Motor protection time constant 1,0 min 1,0 min
L1-03 MOL thermistor input 3 Operation continued 3
L1-04 MOL filter time 1 Coast to stop 1
L1-05 MOL reserved 1 0,20 sec 0,20 sec
L1-13 Electronic thermal continues 1 Enabled 1

L2-01 Momentary power loss detection 2 Enabled while CPU is operating 2

L2-02 Momentary power loss ridethru time 1,0 sec 1,0 sec
L2-03 Min. baseblock time 0,9 sec 0,9 sec
L2-04 Voltage recovery time 0,3 sec 0,3 sec
L2-05 Undervoltage detection level 190 VDC 190 VDC
L2-06 KEB deceleration time 0,0 sec 0,0 sec
L2-07 Momentary recovery time 0,0 sec 0,0 sec
L2-08 KEB Frequency 100 % 100 %
L2-11 Desired DC Bus Voltage during KEB 240 V 240 V

L3-01 StallP acceleration selection 1 Enabled 1

L3-02 StallP acceleration level 120 % 120 %
L3-03 StallP CHP level 50 % 50 %
L3-04 StallP deceleration selection 0 Disabled - The drive decelerates at the selected Dec time.If 0
the load is too large or the Dec time is too short, an OV fault
L3-05 StallP running selection 0 Disabled
may occur. 0
L3-06 StallP running level 120 % 120 %
L3-11 OV Inhibit selection 0 Disable 0
L3-17 Overvoltage Suppression and Deceleration 370 V 370 V
Stall and Desired DC Bus Voltage during
L3-20 Adjustment
Motor Stall Gain 1,00 1,00
L3-21 Deceleration rate operation gain 1,00 1,00
L3-23 StallP running level output auto reduction 0 Sets the stall prevention level throughout the entire frequency 0
range to the value in parameter L3-06.
L3-24 Inertia conversion motor acceleration time 0,265 sec 0,265 sec
L3-25 Load inertia P 1,0 1,0

L4-01 Speed agreement level 0,0 Hz 0,0 Hz

L4-02 Speed agreement width 2,0 Hz 2,0 Hz
L4-03 Speed agreement level +- 0,0 Hz 0,0 Hz
L4-04 Speed agreement width +- 2,0 Hz 2,0 Hz
L4-05 Reference loss selection 0 Stop 0
L4-06 Frequency reference at floss 80,0 % 80,0 %
L4-07 Conditions of Frequency detection 0 No detection during baseblock. 0

L5-01 Number of auto restart attempts 5 time(s) 5 time(s)

10/15
 Default
Parameter Value Information Setting
L5-02 Auto restart operation selection 0 Not output(Fault contact is not activated) 0
L5-04 Fault Reset Interval Time 20,0 sec 20,0 sec
L5-40 Low Feedback Fault Retry Selection 0 No retry 0
L5-41 High Feedback Fault Retry Selection 0 No retry 0
L5-42 Feedback Loss Fault Retry Selection 0 No retry 0
L5-50 Setpoint Not Met Fault Retry Selection 0 No retry 0
L5-51 Loss Of Prime Fault Retry Selection 0 No retry 0
L5-52 Pump Over Cycle Fault Retry Selection 0 No retry 0
L5-53 Volute-Thermostat Retry Selection 0 No retry 0

L6-01 Torque detection selection 1 0 Disabled 0

L6-02 Torque detection level 1 15 % 15 %
L6-03 Torque detection time 1 10,0 sec 10,0 sec
L6-04 Torque detection selection 2 0 Disabled 0
L6-05 Torque detection level 2 150 % 150 %
L6-06 Torque detection time 2 0,1 sec 0,1 sec
L6-13 Motor Underload Protection Selection 0 Base Frequency enable 0
L6-14 Motor Underload Protection Level at Min. 15 % 15 %
Frequency

L8-01 DB resistor protect 0 Disabled 0

L8-02 Overheat pre-alarm level 121 deg 121 deg
L8-03 Overheat pre-alarm selection 3 Operation continued(monitor display only) 3
L8-05 Phase loss input selection 1 Enabled 1
L8-07 Phase loss output selection 1 1PH loss detection 1
L8-09 Ground protection selection 1 Enabled 1
L8-10 Cooling fan control selection 0 Operates when inverter is running 0
L8-11 Cooling fan control delay time 300 sec 300 sec
L8-12 Ambient temperature 40 deg 40 deg
L8-15 OL characteristics at low speeds 1 L8-16,17 setting enable 1
L8-18 Software CLA selection 1 Software CLA enable 1
L8-19 Frequency Reduction Rate during OH 0,8 0,8
Pre-Alarm
L8-38 Carrier frequency decel selection 2 Overload career frequency decreases gradually 2
L8-40 Reduction carrier frequency time 0,50 sec 0,50 sec
L8-41 Current warning 0 Disable 0

n1-01 Hunting-prevention selection 1 Enabled 1

n1-02 Hunting-prevention gain 1,00 1,00
n1-03 Hunting-prevention time 10 ms 10 ms
n1-05 Reverse hunting prev gain 0,00 0,00

n3-13 Over exciting deceleration gain 1,10 1,10

n3-21 Over slip inhibit current level 100 % 100 %
n3-23 Over Excitation Run 0 Disable 0

o1-01 Monitor selection 106 Output voltage 106

o1-02 Monitor selection after power up 1 Frequency reference 1
o1-03 Display scaling 0 0.01Hz units 0

11/15
 Default
Parameter Value Information Setting
o1-05 LCD Contrast 3 3
o1-06 User Monitor Selection Mode 1 3 Monitor Selectable 1
o1-07 Second Line Monitor Selection 102 Output frequency 102
o1-08 Third Line Monitor Selection 191 191
o1-12 Home Help Text 1 Enabled 1

o2-02 Operation STOP key 1 Always enabled 1

o2-04 KVA selection 6B CIMR-PW2V0040*** 6B
o2-05 Frequency Reference Setting Method 0 Disabled 0
Selection
o2-06 Operator detection 0 Operation continues even if the dig. Operator is disconnected 0
o2-07 Bidirectional when the inverter power is on 0 Forward run 0
o2-09 Initialize mode selection 1 American spec 1
o2-30 Monitor Position Save 0 Disabled 0

o3-02 Copy Allowed Selection 1 Enabled - Copying allowed. 1

o4-02 Cumulative operation time selection 1 Cumulative Inverter run time 1

o4-03 Fan operation time setting 0 1=10H 0 1=10H
o4-05 Capacitor maintenance setting 0% 0%
o4-07 Rush-in prevention relay maintenance setting 0 % 0%
o4-09 IGBT maintenance setting 0% 0%

3 Memobus network 0
P1-02 System Units 1 PSI (Pounds per Square Inch) 1
200,0 PSI 145,0 PSI
-7,0 PSI 0,0 PSI
P1-05 Start Level Delay Time 1 sec 1 sec
30,0 Hz 40,0 Hz
P1-07 Minimum Pump Speed Units 0 Hz 0
15,0 PSI 0,0 PSI
P1-09 Low Feedback Level Fault Delay Time 10 sec 10 sec
P1-10 Low Feedback Selection 0 Fault 0
120,0 PSI 155,0 PSI
P1-12 High Feedback Level Fault Delay Time 5 sec 5 sec
P1-13 High Feedback Selection 0 Fault 0
P1-14 Hysteresis Level 0,0 PSI 0,0 PSI
P1-15 Maximum Set Point Difference 0,0 PSI 0,0 PSI
P1-16 Not Maintaining Setpoint Time 60 sec 60 sec
P1-17 Not Maintaining Setpoint Selection 0 Fault 0
P1-18 Prime Loss Detection Method 0 Current (A) 0
12,0 A 0,0 A
P1-20 Loss of Prime Time 20 sec 20 sec
P1-21 Loss of Prime Frequency 0,0 Hz 0,0 Hz
P1-22 Loss of Prime Selection 0 Fault 0
P1-23 Loss of Prime Maximum Restart Time After 0,2 min 0,2 min
Fault
P1-30 Low Water DI Configuration 0 Normally Open 0
P1-31 High Water DI Configuration 0 Normally Open 0

12/15
 Default
Parameter Value Information Setting

P2-01 Sleep Level Type 0 Output Frequency 0

49,0 Hz 0,0 Hz
10 sec 5 sec
P2-04 Sleep Activate Level 0,0 Hz 0,0 Hz
5,0 PSI 0,0 PSI
P2-06 Sleep Boost Hold Time 5,0 sec 5,0 sec
P2-07 Sleep Boost Maximum Time 20,0 sec 20,0 sec
P2-08 Delta Sleep Feedback Drop Level 0,0 PSI 0,0 PSI
P2-09 Feedback Detection Drop Time 10,0 sec 10,0 sec
P2-10 Sleep Mode: Cycling Protection 0 0
P2-11 Sleep Mode: Maximum Cycling Protection 300 sec 300 sec
Time
P2-12 Over Cycling Mode 0 Disabled 0
P2-13 Setpoint Compensation 0,0 PSI 0,0 PSI
P2-14 Maximum Setpoint Compensation 0,0 PSI 0,0 PSI
P2-23 Anti-No-Flow BandWidth 0,40 % 0,40 %
P2-24 Anti-No-Flow Detection Time 10,0 sec 10,0 sec
P2-25 Anti-No-Flow Release Level 3,0 PSI 3,0 PSI

40,0 PSI 0,0 PSI

40,0 Hz 0,0 Hz
1,0 min 0,0 min
P4-05 Pre-Charge Loss Of Prime Level 0,0 A 0,0 A
P4-06 Pre-Charge Frequency 2 0,0 Hz 0,0 Hz
P4-07 Pre-Charge Time 2 0,0 min 0,0 min
P4-08 Pre-Charge Loss Of Prime Level 2 0,0 A 0,0 A
P4-10 AUTO Mode Operator Run Power Down 0 Disabled 0
Storage
P4-11 Thrust Bearing Acceleration Time 1,0 sec 1,0 sec
0,0 Hz 30,0 Hz
P4-13 Thrust Bearing Deceleration Time 5,0 sec 5,0 sec
P4-17 Utility Start Delay 0,2 min 0,2 min
P4-21 Low City Input Select 1 Normally Closed 1
P4-22 Low City On-Delay Time 10 sec 10 sec
P4-23 Low City Off-Delay Time 5 sec 5 sec
P4-24 Low City Water Alarm Text 0 Low City Pressure 0
P4-25 Remote Drive Disable Selection 1 Normally Closed 1
P4-26 Remote Drive Disable On-Delay 0 sec 0 sec
P4-27 Remote Drive Disable Off-Delay 0 sec 0 sec
P4-29 Lube Pump Message 0 Lube Pump 0
P4-30 Lube Pump Active during Run 0 Disabled 0
P4-31 Lube Pump Delay Timer 0,0 sec 0,0 sec
P4-32 Pre-Charge Level 2 0,0 PSI 0,0 PSI

P5-01 Hand Mode Reference Source 1 P5-02 (Hand Reference) 1

60,0 Hz 40,0 Hz
P5-03 Hand/Auto During Run Selection 0 Disabled 0
0 Disabled 1

13/15
 Default
Parameter Value Information Setting
P5-05 Hand Reference 2 0,0 Hz 0,0 Hz
P5-06 Hand Ref. 1 Loss Of Prime Level 0,0 A 0,0 A
P5-07 Hand Ref. 2 Loss Of Prime Level 0,0 A 0,0 A
P5-09 HAND References Set via Motor Operated 0 Disabled 0
Pot Selection

P7-01 Anti-jam Selection 0 Disabled 0

P7-02 Anti-Jam Cycle Count 1 1
P7-03 Anti-Jam Detection Current Level 120 % 120 %
P7-04 Anti-Jam Detection Time at Start 0,3 sec 0,3 sec
P7-05 Anti-Jam During Run Current 0% 0%
P7-06 Anti-Jam During Run Time 0,3 sec 0,3 sec
P7-07 Anti-Jam Frequency Reference 25,00 Hz 25,00 Hz
P7-08 Anti-Jam Release Time 2,0 sec 2,0 sec

0 Next Available 1
3 Network Only 0
1 min 24 min
3 LIFO at Sleep 0
P9-05 Lag Mode 0 Fixed Speed 0
59,0 Hz 55,0 Hz
1 sec 5 sec
2 Feedback Level + Output Frequency 0
P9-09 Add Frequency Level 59,5 Hz 59,5 Hz
1,0 PSI 4,0 PSI
1 sec 10 sec
2 Feedback Level + Output Frequency 0
51,0 Hz 40,0 Hz
1,0 PSI 0,0 PSI
6 sec 10 sec
P9-16 Stabilization Time 3 sec 3 sec
P9-17 Setpoint Modifier 0,0 PSI 0,0 PSI
P9-18 High Feedback Quick De-stage 97,0 % 97,0 %
1 Minutes (min) 0
P9-20 Allow Network Run 0 Always 0
P9-21 Run Priority 8 8
P9-22 System Fault Retry 5 5
2 4
P9-24 Lead Swap at Sleep 0 sec 0 sec
2 4
P9-26 Master Time-out 4,0 sec 4,0 sec
P9-27 Network Recovery 0 Automatic 0
P9-28 NETSCAN Alarm Time 2,0 sec 2,0 sec
P9-29 Net Start Delay 2,0 sec 2,0 sec
P9-30 Lag Drive Speed FolLower Gain 100,0 % 100,0 %
P9-31 Lag Drive Speed FolLower Bias 0,00 Hz 0,00 Hz
P9-32 Lag FolLower Deceleration Time 60,0 sec 60,0 sec
P9-33 Lag FolLower Decel. Active Time 0,0 sec 0,0 sec

14/15
 Default
Parameter Value Information Setting
P9-34 Low Feedback Quick De-stage 0,0 PSI 0,0 PSI
P9-99 Network Compatibility Selection 2 iQ Smart Network 2

45,0 PSI 0,0 PSI

Q1-02 PID Controller Setpoint 2 0,0 PSI 0,0 PSI
Q1-03 PID Controller Setpoint 3 0,0 PSI 0,0 PSI
Q1-04 PID Controller Setpoint 4 0,0 PSI 0,0 PSI
Q1-09 PID Setpoint Set via Motor Operated Pot 0 Disabled 0

Q3-01 Output Current Limit Select 0 Disabled 0

Q3-02 Current Limit 0,0 A 0,0 A
Q3-10 Single Phase Foldback Selection 1 Enabled 1
Q3-11 Ripple Regulator Setpoint 95,0 % 95,0 %

S6-01 Emergency Override Speed 0,00 Hz 0,00 Hz

S6-02 Emergency Override Reference Selection 0 Use S6-01 Reference 0

15/15