PART A

SEMESTER : 4 SUBJECT : SOM SUBJECT CODE :

FILL IN THE BLANKS
Cha Qusti
Sub Categ
pter Chapter Name Topic Name on
Topic ory
s No.

1 Bending Stress A 1

A 2

A 3

B 4

C 5

A 6

2 Torsion of Shaft C 7

B 8

A 9

A 10

A 11

3 Torsion of Springs B 12

C 13

A 14

B 15

C 16

A 17

C 18
A 19
A 20
A 21
A 22
 B 23
A 24
DIRECT SHEAR
2 C 25
STRESESS

A 26

C 27

THERMAL EFFECT
3 ON STRESS AND A 28
STRTAIN
A 29
C 30
STRUTS AND
4 C 31
COULMN
A 32
C 33
A 34
C 35
C 36
 PART A
BJECT : SOM SUBJECT CODE : CP01 04 09
FILL IN THE BLANKS
NEAREST
QUESTION ANSWER
ANSWER

For a Canti lever of length L, and the point load W act at the
end, then Bending moment, M= _____________

Bending Stress is expressed in ___________________

An example of bending spring is
_______________________
The stresses introduced by bending moment are known as
___________.
The unit of strain is ___________.
The bending stress is inversely proportional to
______________.
Bending stress is expressed in ___________.
In a circular section of diameter d, the polar moment of
inertia is _____________

The formula for Young Modulus is ___________.

Hook’s law holds good up to ____________ limit.

Unit of twisting moment is ____________.

The unit of Polar Modulus is _________________

In a circular section of diameter d, the Moment of inertia, I =

_____________

Unit of stiffness is ____________.

The power transmitted by the shaft P = ______________

KW
Moment of Inertia of Hollow shaft is ___________.
The beam which is fixed at one end and free at the other
end is known as ___________ beam

Moment of Inertia of Hollow shaft is ___________.

An example of Bending Springs is __________________.

The power transmitted by the shaft P = ______________
-
KW
Section modulus Z=__________.
`
 PART A
SEMESTER : 4 SUBJECT : SOM S
CHOOSE THE CORRECT
Cha
Sub Questi
pter Chapter Name Topic Name Category
Topic on No.
s
1 Bending Stress 1

3
4
5

10

11

12

2 Torsion of Shaft 1

4
5
 6

Torsion of Springs 1
3

4
 PART A
:4 SUBJECT : SOM SUBJECT CODE : CP01 04 09
CHOOSE THE CORRECT ANSWER

Questions A B C

2° =__________ radians 0.0348 0.067 0.09

The width of abeam is 60 mm and

1080000 mm3 72000 mm3 36000 mm3
thickness is 60 mm Then the Moment of
inertia is
Unit of Shear Modulus is N/m N/mm2 N-m
Section modulus is given by Y/I MI/Y I/Y
10 = ___________ radians π /180 π / 90 π / 360
For a rectangular beam width b and depth bd3/12 bd3 / 36 bd3 / 6
d, Moment of inertia, I =
When a helical compression spring is
subjected to an axial compressive load, Tensile Compressive Bending
the stress induced is
The maximum bending moment of a
cantilever beam of length L and a load W
at its free WL WL/2 WL/4
end is given by
The stress developed at the centre of the
shaft subjected to pure torsion is Maximum Minimum Zero
For a rectangular beam width b and depth bd3/12 bd3 / 36 bd3 / 6
d, Moment of inertia, I =
When a helical compression spring is
subjected to an axial compressive Tensile Compressive Bending
load,the stress induced is
The maximum bending moment of a
cantilever of length L and a load W at its WL WL/2 WL/4
free end is given by

Polar Moment of Maximum radius / Polar Moment of

Polar Modulus = Intertia / Polar Moment of Inertia X
Maximum radius Inertia Maximum radius

Section modulus is given by Y/I MI/Y I/Y

Power, P = 60000 2πNT , the unit of T is
______ N/m Nm N/m2

M= Z+F f/ Z Z/f
Torsional rigidity is given by C X Ip C/Ip CƟIp
The ratio of direct stress to volumetric strain is Young’s
known as Rigidity modulus Bulk modulus
modulus

The leaf spring is an example of

Torsion Spring Bending spring Coiled spring
________________
When a closely coiled spring is subjected to
Bending Shear Torsion
an axial load, it is said to be under
 D Answers

0.123

24000 mm3

N-mm2
f/y
1/ π

bd3 / 8

Shear

none of these

Unpredictable

bd3 / 8

Shear

none of these

none of these

f/y

N/m3

f*Z
Ip* C
none of these

None of these

All of these
 PART A
SEMESTER : 4 SUBJECT : SOM SUBJECT CODE : CP
MATCH THE FOLLOWING
Chapt
Chapter Name Sub Topic Topic Name Category
ers

1 Bending Stress A

2 Torsion of Shaft B

3 Torsion of Springs B

C
C
C
UBJECT CODE : CP01 04 09
WING
Question
A Questions B Question
No.

1 Bending Moment

2 Shear stress

3 Stiffness
4 Strain

5 Young’s Modulus

6 Polar Moment of inertia

7 Moment of inertia

8 Load
9 Section Modulus
10 Power
11 Torque