SET 1  Bituminous fiber sewer pipe-

cheapest, light in weight,

(Practical problems #1: 1-100) recommended for house sewer and
septic tank installation. It could take
slight soil movement without danger
of cracking or pulling out of its joint.
1. The unit of kinematic viscosity.
a. N/mm
5. What is the minimum size of p-trap to be
b. Reynolds
installed with the water closet fixture.
c. Poise
a. 2 inches
d. Stokes (St)
b. 3 inches
c. 4 inches
 CGS unit (centimeter-gram-second
d. None of the above
system units)
 Named after Sir George Gabriel Stokes
 P-trap size for water closet is 76
mm converted to inches is 2.99
or 3 inches pipe.
2. What is the least method to lay a PB or
PE tubing?
6. For iron pipe sizes and fittings, joints
shall be
a. Stretched
b. On steel sleeves
a. Threaded
c. Snake like
b. Wiped
d. Straight-line
c. Screwed
d. Caulked
https://www.proprofs.com/quiz-
school/quizshow.php?title=mtgxm
 NPC Section 1302.2-Types of
dyxnas2h6&q=97
Joints.
3. The difference in pressure between the Threaded Joints- for iron pipe size
suction and discharge sides of the pump. (IPS) pipe and fittings shall be
standard taper pipe threads.
a. Drawdown
b. Static Lift
c. Total dynamic head 7. Colling and airconditioning equipment
d. Net positive suction head shall be separated from the drainage
system by an__________ and all food
 The difference between inlet equipment separated by an_________.
pressure and the lowest pressure level
inside the pump is called NPSH: Net a. Air break, air break
Positive Suction Head. NPSH is therefore b. Air gap, air break
an expression of the pressure loss that c. Air gap, air gap
takes place inside the first part of the d. Air break, air gap.
pump housing
 NPC (p.90) Section 801.2
4. Cheapest, Light in weight and could take
slight soil movement without danger of 8. What is the minimum center-to-center
cracking or pulling out of its joints. distance of urinals?

a. Brass pipe a. 03 mm
b. Bituminous fiber sewer pipe b. 0.375 mm
c. Acid resistant cast iron c. 0.6mm
d. Vitrified clay pipe d. 0.75 mm

 600 mm (24”)
9. It is a type of backflow prevention device 13. It is used in drainage piping serving
that consists of a loaded air inlet valve, fixtures which have flood level rims
and internally loaded check valve, two located below the elevation of the
properly located test cocks and two nearby upsteam manhole invert of the
isolation valves. public sewer, to protect against
backflow of sewage.
a. PVB
b. AVB a. Air gap
c. DCV b. CT and PRV
d. RPP c. Back water valve
 See pdf “Water suppy and d. Double Check valve
Distribution”
Section 603.1 Backflow 14. What material can be used for indirect
prevention devices waste pipe conveying undiluted
Section 603.1.4 PVB condensate water from fuel burning
condensing equipment.
10. What does CT and PRV mean?
a. Galvanized iron
a. Combination temperature and b. Plastic
Pressure relief Valve c. Cast iron
b. Combination Temperature and d. All of the above
Pressure Regulating Valve
c. Combined Temperature and  SEE SECTION 807.3.2 THEN
Pressure Relief Valve PROCEED TO SECTION 701 OF
d. Combined Temperature and REVISED NATIONAL PLUMBING
Pressure Regulating Valve CODE OF THE PHILIPPINES

15. In water piping installation, what are the

11. How many fixture units shall be allowed allowable types of material for valves
for each 0.63 L/s of flow or each GPM with a diameter of 100 mm.?
flow in sizing building drain or sewer
receiving discharge in any pump or a. Brass and cast iron
ejector? b. Galvanized malleable iron
c. Galvanized cast iron and
a. 1 malleable iron
b. 2 d. Brass and galvanized iron
c. 3
d. 4  SECTION 1410 OF REVISED
NATIONAL PLUMBING CODE OF
 NPC (p.81) THE PHILIPPINES
 Brass works particularly well in
12. Determine the size of the soil stack hot water applications, and is
serving 2 WC, 2 LAV, 2 BT and 2 SHO. highly resistant to corrosion.
 https://www.plumbingsupply.c
a. 76 mm om/fittings-guide.html
b. 102 mm  https://www.nuflowmidwest.co
c. 127 mm m/two-common-types-of-
d. 152 mm plumbing-pipes-used-in-multi-
unit-residential-construction/
 2 WC x 3 = 6
2 LAV x 1 = 2 16. The only indirect waste receptor allowed
2 BT x 2 = 4 in bathroom and toilet areas.
2 SHO x 2 = 4
Total: 16 FU a. Standpipe for clothes washer
 b. Closed condenser  An end pipe wrench has a head
c. Open condenser at a bit of angle and is designed
d. Intercepting sump to be used on pipes close to the
wall or parallel work.
 SECTION 804.1 OF REVISED  An offset pipe wrench is used to
NATIONAL PLUMBING grab onto pipes at awkward
CODE OF THE PHILIPPINES angles or in tight spots.
 A compound leverage pipe
17. What is the maximum trap loading for a wrench is used for seized joints
102 mm pipe? and provides extra leverage
 Strap wrench- a type of wrench
a. 4 FU that grip an object via a strap or
b. 6 FU chain.
c. 8 FU
d. 10 FU 21. What is the pipe connecting upward
from a soil or waste drain to main stack
 Table 7-1 p. 79 (NPC) for the purpose of preventing pressure
changes in the stack.
18. ______ means any pipe or fitting which
makes an angle of more than 45 deg with a. Riser
vertical. b. Main vent
a. Diagonal pipe c. Relief vent
b. Horizontal pipe d. Yoke vent
c. Vertical pipe
d. Cross pipe  NPC- Chapter 2: Desciption
page 33
19. The area coverage of one sprinler for
light hazard occupancy. 22. To prevent rusting of the end of the vent,
what fitting should be installed?
a. 10 sq.m
b. 15 sq.m a. Wye and 1/8 elbow
c. 20 sq.m b. Tee
d. 25 sq.m c. End cap
d. Bushing
 The coverage of one sprinkler
head varies from about 20 sq.m  https://essentrapipeprotec
(200 sq.ft) per sprinkler for light tion.com/pipe-end-
hazard occupancy (like hospital, protectors-keep-business/
residences) to about 9 or 10
sq.m (90 sq.ft) for extra hazard 23. Water is how many time heavier than
conditions (like chemical, air?
woodworking, aircraft hangars)
a. 830
20. It is a type of wrench with jaws parallel b. 308
to the handle and it is used to grab into c. 300
pipes at awkward angles or in tight d. 803
spots.
 Water is mostly in the liquid
a. Compound leverage wrench phase, with molecules much
b. End pipe wrench closer to each other, at room
c. Strap wrench temperature and atmospheric
d. Offset wrench pressure due to intermolecular
forces
  See Chapter 1 page 2 “Plumbing cast iron or brass bodies. Each gate valve shall be
and Sanitary” by George Salvan a fullway type with working parts of non-
corrosive materials
24. Branch vents are required to have at
least a slope of ¼” per foot. The purpose
of which is 27. The yoke vent connection with the vent
stack shall be placed not less
a. To avoid scaling than______ above the floor level
b. To avoid backflow
c. To prevent clogging of solid a. 500 mm
particles b. 750 mm
d. To avoid bad smell c. 1000 mm
d. 1250 mm
 SECTION 905.1 REVISED
NPC (p. 104) Section 907.2- The yoke
NATIONAL PLUMBING
vent connection with the vent stack
CODE OF THE
shall be placed not less than 1.0
PHILIPPINES
meter above the floor leve), and the
 A,C doesn’t make any
yoke vent connection with the
sense.
drainage stack shall be by means of
 Water seals in traps are
a wye branch fitting placed below
the one that prevent
the fixture branch serving that floor.
sewer gases from
entering buildings.
 28. Approved material pipes for vent pipes.
25. Joints between lead pipe and cast iron
shall be made by means of__________ a. Series 1000 PVC
b. Cast iron
a. Bell and spigot c. Malleable iron pipe
b. Caulking ferrule or soldering d. Schedule 80 ABS
nipple
c. Soldering  NPC (p. 101) Under Section
d. Welding 903.1 – Vent pipes shall be cast
iron, ductile cast iron, galvanized
 NPC (p. 140) Under section steel, galvanized wrought iron,
1303- Use of Joints stated that: lead, copper, brass, Schedule 40,
 Section 1303.4- Lead to Cast ABS, DWV, Series 1000, PVC,
Iron pipe, Wrought iron or steel DWV
– joints between lead and cast
iron, wrought or steel pipe shall 29. Refrigeration waste size for 4 to 12m3;
be made by means of wiped 32 mm inlets or the equivalent
joints to a caulking ferrule, refrigeration space.
soldering nipple or bushing.
a. 32 mm
26. Valves of 51 mm size should be made of b. 51 mm
what type of material? c. 76 mm
d. 102 mm
a. Steel
See NPC (p.99) Section 818-Refrigeration Waste
b. Brass
c. PVC 32 mm -- l inlet serving not more than 2.8 m3 of
d. Cast iron refrigeration space
NPC (p. 54) Section 605.1 - Valves up to and 51 mm- 4 to 12m3, 32 mm inlets or the
including 51 mm in size shall be brass or other equivalent refrigeration space
approved materials. Sizes over 51 mm may have
76 mm-13 to 36m3, 32 mm inlets or the  The dip tube in your water
equivalent refrigeration space heater, (and nearly all water
heaters have them), is a long
plastic tube that fits into the
30. Fine corrosion-resistance screen for
inlet of the water heater and
openings in an elevated or gravity
stops at about 8 inches above
storage tank should not be less than
the bottom of the tank. Some
water heaters have the cold
a. 14 nor more than 18
water inlet at the bottom of the
b. 18 nor more than 22
tank, and those water heaters
c. 12 nor more than 16
do not need a dip tube since
d. 16 nor more than 20
the cold water is already
See NPC (p.65)Section 606.1 entering the tank from the
bottom.
The covers of gravity tanks shall be vented with
a retum-bend vent pipe having an area not less 34. How do you cut a cast iron?
than the area of the down-feed riser pipe, and
the vent shall be screened with a fine corrosion-
a. Using arc welding
resistant screen with openings not less than 14 b. Using cold chisel
ncr more than 18 mess per 25 mm.
c. Using reamer
31. A metallic sleeved, caulked or joined to d. Using arc welding
an opening in a pipe, into which plug is handheld method to cut through a cast
screwed that can be removed for iron pipe is with a cold chisel and ball
cleaning and examining the interior of
peen hammer.
the pipe.
Although this method actually makes
a. Neoprene gasket the cut more easily, the downside is
b. Ferrule that it requires a lot of skill to perform
c. Shielded coupling successfully.
d. Flange
Because of the skill and experience
See NPC (p. 16)Chapter 2: Description of Ferrule required, the cold chisel method should
only be used by those that already
know how to use this hand tool.
32. What will be the least consideration
before doing an excavation work?
35. To properly secure a water cooler to a
a. Equipment to be used
wall, use structural backing or________
b. Material and backfill present in
the area
a. Two cross members
c. Water table level
b. A mount for the supply piping
d. None of the above
c. Floor mounting
d. A carrier
33. Where is a dip tube present?
36. The drain bodies of floor drains
a. Catch basin
designed to be used with a waterproof
b. Sump pit
membrane are designed with
c. Cold water tank
d. Hot water tank
a. Weep holes
b. Mechanical trap seals
 Dip Tubes are very important to
c. Backflow preventer
the operation of gas and
d. Weight bearing deck clamps
electric water heaters. Without
a dip tube you won’t get much
hot water.
37. Decorative color plates for the carrier a. Cesspool
arm wall penetrations are called______ b. Bidet
c. Privy
a. Flanges d. Latrine
b. Finials
c. Escutcheon  NPC (page 21) Chapter 2:
d. Sconces Description

 An escutcheon plate is the disc 41. What material property characterizes

around a plumbing pipe at the cast iron pipe?
wall penetration that seals the
wall opening a. Brittleness
 “Collars or escutcheon plates b. Flexibility
shall be provided to cover the c. Ductility
openings around pipes d. Malleability
penetrating walls, floors, or
ceilings in finished areas that 42. Roof deck strainers for use on sun
are exposed to view.” decks, parking deck shall be of an
approved flat surface typed equipped
38. What do you call the piece or tubing that with a strainer having a total net inlet
connects the outlet of a plumbing fixture area of not less than
to the trap?
a. Equal the area of outlet pipe
a. Tailpiece b. 1 ½ times the area of outlet
b. Connector pipe
c. Outflow c. 2 times the area of outlet pipe
d. Heat tubing d. 2 ½ times the area of outlet
pipe
 tailpiece is the short piece of
See NPC (p.118) Section 1103.1.1.1
pipe between a fixture drain
and a trap. Roof drains shall be equipped with strainers
extending not less than to 102 mm above the
39. The appropriate sealant that will be surface of the roof immediately adjacent to the
used to cover void spaces between drain, Dome-Type Strainers shall have a
pipes and sleeves through concrete minimum total net inlet area of 1 ½ times the
floors in the ground. area of the outlet pipe to which it is connected.

43. Plastic pipes and fittings designed to be

a. Grease
joined by solvent cementing shall
b. Epoxy
comply with appropriate installations
c. Putty
standard of this organization
d. Bitumen
a. NPC
 NPC (p.38) Section 302-
b. PNS
Protection of Piping and
c. IAPMO
Structures
d. ASTM
“Void between pipes and sleeves
through concrete floors in the
 See NPC (p.138) Section
ground shall be appropriately
1302.11
sealed with bitumen”
 Solvent Cement Plastic Pipe
Joints- Plastic pipes and fittings
40. A water closet with continuous through
designed to be joined by
containing water.
solvent cementing shall comply
 with the appropriate IAPMO b. Subtracting the inside diameter
Installation Standards. from the outside diameter and
divided by 2
44. Brass or copper ground joint, flared on c. Subtracting the inside from the
ferrule type connections when made up outside diameter
shall not be considered as _____ joints. d. All of the above

a. Slip 48. PVC pipe cannot be used for

b. Screw
c. Welded a. Venting a drainage system
d. Flange b. Drain and sewers
c. Cold water service from a water
 NPC (p.140) Section 1304.5 meter to a building
 Ground Joint, Flared or Ferrule d. Hot water distributing system
Connections - Brass or copper
ground joint, tlarcd or ferrule 49. A ball valve
type conuections when made
up, shalt not be considered as a. Can be purchased as an
slip joints. automatic type
45. Joining method of installation for PPR b. Has an internal ball with a core
pipes? drilled its center
a. By heating c. Has a lever handle for manual
b. By threading types
c. By solvent cement d. All of the above
d. None of the above
50. Neoprene rubber shall be used in soils
46. For a residential with one shower only, subject to
what is the best water heating system?
a. Oil intrusion
a. Single point system b. Contamination
b. Multipoint system c. Erosion
c. Centralized system d. Pollution
d. All of the above
 NPC (p.139) Section 1302.13
 single point hot water heater states that “Molded Rubber
can be fueled by gas or Coupling Joints - when pipe is
electricity and heat the water joined by means of molded
only when it is required. These neoprene rubber coupling
are usually fitted with a swivel .ioints, such joints shall conform
spout and located directly above to approved standards and shall
a sink or wash basin. The gas not be considered as slip joints.
fired heater heats up the water When required, appropriaie
twice as fast as the electric neoprene rubber bushings shall
heater and costs less to run. be used to allow for any
difference in piping material
diameters. Neoprene rubber
47. How is the wall thickness of a pipe shall be used in soils subject to
determined? oil intrusion”
51. What is the handy tool for threading the
a. Adding the inside and the end of the pipe in a trench or in the
outside diameter and divided corner of a cellar where a pipe projects
by 2 too far and threaded in a place?

a. Traps
 b. Ratchet Stooks plumbing system. Which in the list is not
c. Geared pipe threader a purpose?
d. Single wheel pipe threader
a. To convey pipe smell on the
52. Where should gat valve be used? pipe
b. To enable the drain to drain
a. After the water meter faster and better
b. At the midpoint between the c. To protect the seal in the trap it
corporation stop and the curb serves
stop d. To carry the combustible sewer
c. In between the main supply line gass out of the building.
and pump line
d. After the entrance of the street 58. Which of the following do not require
water main installation of a clean out?

53. A forty five degree fitting is a. Any change of direction of a soil

branch 22.5 deg. And over
a. One-sixteenth of a circle b. At every branch interval of a soil
b. One-eight of a circle stack
c. One-fourth of a circle c. At the upper end of every soil
d. One-half of a circle branch
d. Any horizontal water or soil
54. The extended portion of a pipe that is pipe exceeding 15 meters.
closed in one end to which no
connections are made on the extended 59. A single vent that ventilates multiple
portion thus permitting stagnation traps in the case of a back to back
wastewater or air therein. fixtures.

a. Dead end a. Back vent

b. Junction box b. Crown vent
c. Building sewer c. Individual vet
d. House drain d. Common vent

 NPC (p.15) Section 205  Also known as unit vent

55. A type of water closet having a flush tank 60. Water distribution system, which
attached at the back of the closet bowl. constantly rely its pressure from main
water pipe, applied only if the highest
a. Close coupled fixture is supplied continuously with the
b. Corner toilet flow rate and minimum required
c. One piece working pressure.
d. Low profile
a. Zoning system
56. A parameter in sizing a horizontal soil b. Booster system
branch pipe. c. Down feed method
d. Upfeed or direct method
a. Amount of fall pipe
b. Type of venting system
c. Number of branch vents 61. The recommended fall per foot for a 3
d. Number of soil or waste branch inch pipe and smaller is

57. The following are the list of purposes of a. ½ inch per foot
providing a venting system in the b. ¼ inch per foot
c. 5/8 inch per foot
 d. 1/8inch per foot sMsiskJGPqSupXW8X2ljP8b1U on
question no. 47
62. Which type of line has become obsolete
and is seldom used?
67. A. Metallic
a. Dry standpipe
b. Wet standpipe  The rubbers absorb the
c. Wet standpipe and siamese constituents of the gasoline.
d. Automatic system Rubber is not suitable for gasket in
gasoline conduction.

63. Why is a wet standpipe with Siamese 68. B. 100 mm

connection considered most practical.
.https://cdn.fbsbx.com/v/t59.2708-
a. It is a cheaper type of 21/11417985_947784591908703_5785
connection 1845_n.pdf/137705105-Practical-
b. There is no need for a fire Problems-
department pumper to be used CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
c. It is the specification of the fire ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
department yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
d. It is being served by the 5FPhHqFQIVn29-
domestic water supply system nbH6BK1A8D43wTo5iFOWZeJY72A&_n
under constant pressure. c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
64. A pipe vise is needed to wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh
=ece81daaf10ac650293d699051df9002
a. Keep rigid for nothing &oe=5D02502B&dl=1&fbclid=IwAR32C
b. Straighten a tapered tap in a mj0qwaH063hxnoFCWSqAm-FVwreH-
hole sMsiskJGPqSupXW8X2ljP8b1U question
c. Expands the ends of the lead no. 50
pipe
d. Retain molten lead in a joint 69. C. 3/4 gpm

 https://www.engineeringtoolbo
65. C. Melting the pipe end x.com/fixture-water-capacity-
d_755.html
66. C. Rubber
70. A. 5%
https://cdn.fbsbx.com/v/t59.2708-
21/11417985_947784591908703_5785  https://www.copper.org/applic
1845_n.pdf/137705105-Practical- ations/plumbing/techref/tpf_st
Problems- ds/fttgs_stds.html
CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D 71. B. 4
5FPhHqFQIVn29- https://cdn.fbsbx.com/v/t59.2708-
nbH6BK1A8D43wTo5iFOWZeJY72A&_n 21/11417985_947784591908703_5785
c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5 1845_n.pdf/137705105-Practical-
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck Problems-
wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
=ece81daaf10ac650293d699051df9002 ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
&oe=5D02502B&dl=1&fbclid=IwAR32C yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
mj0qwaH063hxnoFCWSqAm-FVwreH- 5FPhHqFQIVn29-
nbH6BK1A8D43wTo5iFOWZeJY72A&_n
 c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5 1845_n.pdf/137705105-Practical-
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck Problems-
wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
=ece81daaf10ac650293d699051df9002 ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
&oe=5D02502B&dl=1&fbclid=IwAR32C yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
mj0qwaH063hxnoFCWSqAm-FVwreH- 5FPhHqFQIVn29-
sMsiskJGPqSupXW8X2ljP8b1U on nbH6BK1A8D43wTo5iFOWZeJY72A&_n
question no. 66 c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
72. D. It will fail to close tightly wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh
=ece81daaf10ac650293d699051df9002
&oe=5D02502B&dl=1&fbclid=IwAR32C
https://cdn.fbsbx.com/v/t59.2708-
mj0qwaH063hxnoFCWSqAm-FVwreH-
21/11417985_947784591908703_5785184
sMsiskJGPqSupXW8X2ljP8b1U on
5_n.pdf/137705105-Practical-Problems-
question no. 79
CTP.pdf?_nc_cat=105&_nc_eui2=AeGMORT
FyLcN8r9cEtcyKGRqh3fiZKBv3kXFwyy8LHaw
75. B. The danger of contamination of the
xYhrvGaQsUSkeKM0elOjHTv6D5FPhHqFQIV
building water supply from the
n29-
unknown source
nbH6BK1A8D43wTo5iFOWZeJY72A&_nc_oc
=AQkm3ahatgq4aQcbkLbUMJI9Q5w6nkx0N
https://cdn.fbsbx.com/v/t59.2708-
rOk9kxw2aEiJ7opHKbf8Dx9CkwnKlnktO8&_
21/11417985_947784591908703_5785
nc_ht=cdn.fbsbx.com&oh=ece81daaf10ac6
1845_n.pdf/137705105-Practical-
50293d699051df9002&oe=5D02502B&dl=1
Problems-
&fbclid=IwAR32Cmj0qwaH063hxnoFCWSqA
CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
m-FVwreH-sMsiskJGPqSupXW8X2ljP8b1U
ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
on question no. 81
yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
5FPhHqFQIVn29-
nbH6BK1A8D43wTo5iFOWZeJY72A&_n
73. D. Iron inserted on the tough floor c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5
sheating and slushed into the concrete w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
slab wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh
https://cdn.fbsbx.com/v/t59.2708- =ece81daaf10ac650293d699051df9002
21/11417985_947784591908703_5785 &oe=5D02502B&dl=1&fbclid=IwAR32C
1845_n.pdf/137705105-Practical- mj0qwaH063hxnoFCWSqAm-FVwreH-
Problems- sMsiskJGPqSupXW8X2ljP8b1U on
CTP.pdf?_nc_cat=105&_nc_eui2=AeGM question no.76
ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
5FPhHqFQIVn29- 76. C. Short offsets and unnecessary fittings
nbH6BK1A8D43wTo5iFOWZeJY72A&_n
c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5 https://cdn.fbsbx.com/v/t59.2708-
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck 21/11417985_947784591908703_5785
wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh 1845_n.pdf/137705105-Practical-
=ece81daaf10ac650293d699051df9002 Problems-
&oe=5D02502B&dl=1&fbclid=IwAR32C CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
mj0qwaH063hxnoFCWSqAm-FVwreH- ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
sMsiskJGPqSupXW8X2ljP8b1U on yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
question no. 80 5FPhHqFQIVn29-
nbH6BK1A8D43wTo5iFOWZeJY72A&_n
74. Poor Wokmanship c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
https://cdn.fbsbx.com/v/t59.2708- wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh
21/11417985_947784591908703_5785 =ece81daaf10ac650293d699051df9002
 &oe=5D02502B&dl=1&fbclid=IwAR32C 5FPhHqFQIVn29-
mj0qwaH063hxnoFCWSqAm-FVwreH- nbH6BK1A8D43wTo5iFOWZeJY72A&_n
sMsiskJGPqSupXW8X2ljP8b1U on c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5
question no. 78 w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh
77. C. Cut and insert coupling =ece81daaf10ac650293d699051df9002
&oe=5D02502B&dl=1&fbclid=IwAR32C
https://cdn.fbsbx.com/v/t59.2708- mj0qwaH063hxnoFCWSqAm-FVwreH-
21/11417985_947784591908703_5785 sMsiskJGPqSupXW8X2ljP8b1U question
1845_n.pdf/137705105-Practical- no. 86
Problems-
80. A. Cast iron pipe
CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw https://cdn.fbsbx.com/v/t59.2708-
yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D 21/11417985_947784591908703_5785
5FPhHqFQIVn29- 1845_n.pdf/137705105-Practical-
nbH6BK1A8D43wTo5iFOWZeJY72A&_n Problems-
c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5 CTP.pdf?_nc_cat=105&_nc_eui2=AeGM
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
=ece81daaf10ac650293d699051df9002 5FPhHqFQIVn29-
&oe=5D02502B&dl=1&fbclid=IwAR32C nbH6BK1A8D43wTo5iFOWZeJY72A&_n
mj0qwaH063hxnoFCWSqAm-FVwreH- c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5
sMsiskJGPqSupXW8X2ljP8b1U on w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
question no. 7 wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh
=ece81daaf10ac650293d699051df9002
78. A. It is convenient to provide a drum &oe=5D02502B&dl=1&fbclid=IwAR32C
valve to make it possible to rain the mj0qwaH063hxnoFCWSqAm-FVwreH-
entire water system sMsiskJGPqSupXW8X2ljP8b1U on
question no. 87
https://cdn.fbsbx.com/v/t59.2708-
21/11417985_947784591908703_5785
1845_n.pdf/137705105-Practical-
Problems-
CTP.pdf?_nc_cat=105&_nc_eui2=AeGM 81. B. Ball peen hammer
ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D 82. B. Used in cleaning pipes of general
5FPhHqFQIVn29- material clinging to pipe walls
nbH6BK1A8D43wTo5iFOWZeJY72A&_n
c_oc=AQkm3ahatgq4aQcbkLbUMJI9Q5 83.
w6nkx0NrOk9kxw2aEiJ7opHKbf8Dx9Ck
wnKlnktO8&_nc_ht=cdn.fbsbx.com&oh 84. C. Figure 11
=ece81daaf10ac650293d699051df9002
&oe=5D02502B&dl=1&fbclid=IwAR32C 85. C. Figure 7
mj0qwaH063hxnoFCWSqAm-FVwreH-
sMsiskJGPqSupXW8X2ljP8b1U on https://quizlet.com/216375065/plumbi
question no. 82 ng-tools-flash-cards/

79. C. Wrought Iron pipe 86. D. for final removal adhering to the
walls and certain roots of fibrous
. https://cdn.fbsbx.com/v/t59.2708- nature
21/11417985_947784591908703_5785
1845_n.pdf/137705105-Practical- https://quizlet.com/216369045/plumbi
Problems- ng-extras-part-1-flash-cards/
CTP.pdf?_nc_cat=105&_nc_eui2=AeGM 87. B. Hot water return line
ORTFyLcN8r9cEtcyKGRqh3fiZKBv3kXFw
yy8LHawxYhrvGaQsUSkeKM0elOjHTv6D
 88. D. Sewer and Vent system scrape stubborn material off
driveways or other hard surfaces.
89. B. Torx

90. A. Figure 17

91. C. Figure 14

92. D. Shower Stall

93. C. Allen

94. D. Figure 16

95. A. Compressed Air

96. A. Skimmer

https://www.swimuniversity.com/pool-
skimmer/

97. A. HDPE

https://www.estormwater.com/read-
between-pipes

98. A. Rising stem gate valve

https://en.wikipedia.org/wiki/Gate_valv
e

99. A. Intercepting sewer

https://quizlet.com/216408841/plumbi
ng-extras-part-2-flash-cards/

100. type of shovel for moving loose garden

materials, sand, top soil or debris. It can
also be used to shape beds, mix
concrete, level off areas that need to be
flat or to scrape stubborn material off
driveways or other hard surfaces.

a. Scoop shovel
b. Round point shovel
c. Square point shovel
d. Trench shovel

http://www.uniontools.com/produ
cts/detail.aspx?ProductId=1924&Su
bFamilyId=424&FamilyId=423&LineI
d=398

 Square point shovel - It's perfect for

moving loose garden material, sand,
top soil or debris. It can also be used
to shape beds, mix concrete, level
off areas that need to be flat or to