Scribd
Upload
70 views6 pages

Material Safety Data Sheet: Roduct Ompany Dentification

This document provides a material safety data sheet for Weathercoat Kool & Seal, a water-based coating formulation manufactured by Berger Paints India Limited. It lists the product ingredients and identifies titanium dioxide and inorganic filler as main components. It also outlines health, physical and chemical properties, safe handling procedures, storage requirements, and disposal methods for the product.

Uploaded by

Argade GV
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views6 pages

Material Safety Data Sheet: Roduct Ompany Dentification

This document provides a material safety data sheet for Weathercoat Kool & Seal, a water-based coating formulation manufactured by Berger Paints India Limited. It lists the product ingredients and identifies titanium dioxide and inorganic filler as main components. It also outlines health, physical and chemical properties, safe handling procedures, storage requirements, and disposal methods for the product.

Uploaded by

Argade GV
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

MATERIAL SAFETY DATA SHEET

1. PRODUCT & COMPANY IDENTIFICATION


IDENTITY : WEATHERCOAT KOOL & SEAL
MATERIAL : WATER BASED COATING FORMULATION

Code None
Date Of Issue 08/01/2016
Chemical Name Or Synonyms :
FORMULA : Not Applicable
AQUEOUS EMULSION BASED COATING

MANUFACTURER’S NAME : BERGER PAINTS INDIA LIMITED

ADDRESS (NUMBER, STREET, CITY, STATE, PIN) :

FACTORY :
TELEPHONE No :
14 & 15 SWARNAMOYEE ROAD
P.O. BOTANIC GARDEN,
+ 91-33-2668-4706 - 09
Howrah – 711103

H.O. :
BERGER HOUSE TELEPHONE No :
129 PARK STREET
Kolkata – 700 017 + 91-33-2229-9724 – 29

PREPARED ON 08/01/2012

P.1 of 6
2. COMPOSITIONAL INFORMATION :

APPROX. TWA/TLV
CAS REG. NO.
WT. % OSHA ACGHI
Polymer Not applicable 50 Max. Not known Not known
Titanium Dioxide (TD) 13463-67-7 40 Max. 5 NE mg/m3

Inorganic Filler (IF) Mixture 50 Max. 15 10 mg/m3


Ethylene Glycol 107-21-1 15 Max. Not known 10 mg/ m3
Not Not
Ester Alcohol (CA) 25265-77-4 10 Max.
established established
330-54-1
4000 mg/Kg.
Preservatives 10605-21-7 5 Max. LD 50 (Oral)
(Approx.)
26530-20-1

Organic Filler mixture Not applicable 10 max Not known Not known

3. HAZARD INFORMATION

EFFECT OF OVER EXPOSURE

 Inhalation : Vapor or mist can irritate the nose, throat and


lungs and cause headache & nausea.

 Skin Contact : Irritating to skin upon repeated or prolonged


contact.

 Eye Contact : Moderately irritating to eyes.

P.2 of 6
4. FIRST-AID MEASURES

 Inhalation : Move subject to fresh air.


 Eye & Skin Contact : Flush eyes with a large amount of water for at
least 15 minutes. See a physician, if irritation
persists. Wash affected skin areas with soap
and water.

 Ingestion : If swallowed, dilute by giving two glasses of


water or drink. See a physician. Never give
anything by mouth to an unconscious person.

5. FIRE HAZARD INFORMATION

 Flash Point : Non-combustible


 Auto Ignition Point : Not applicable
 Lower Explosion Limit (%) : Not applicable.
 Upper Explosion Limit(%) : Not applicable
 Unusual Fire & : Material can splatter above
Explosion Hazards 212F. Polymer film can burn.

6. ACCIDENTAL RELEASE MEASURE

 Steps to be taken in case material is released or spilled


Keep spectators away. Floor may be slippery, use care to avoid falling. Dike
and contain spill with inert material (e.g. sand, earth). Transfer liquid to
containers for recovery or disposal and solid diking material to separate
containers for disposal. Keep spills and cleaning run-offs out of municipal
sewers and open bodies of water.5.0. PHYSICAL PROPERTY / CHEMICAL PROPERTY
INFORMATION.

P.3 of 6
7. STORAGE AND HANDLING INFORMATION

 Storage Temperature : Max. 60C/140F


Min. 10C/34F
 Precautionary Labeling : Keep from freezing — product may
coagulate.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

 Ventilation Type : Mechanical, local exhaust ventilation at point


of contaminated release.

 Respiratory Protection : Wear suitable respirator where exposure limits


are exceeded.

 Protective Gloves : Thin rubber gloves


 Eye Protection : Chemical Splash goggles.

9. PHYSICAL PROPERTY / CHEMICAL PROPERTY INFORMATION

 Appearance : White viscous liquid


 Odour : Mild odour
 pH : 8.5 – 9.0
 Viscosity : Variable
 Melting or Freezing Point : Variable
 Boiling Point : Variable
 Vapour Pressure (mm HG) : Greater than 17 @ 60F
 Vapour Density (Air – 1) : Greater than 1
 Solubility in Water : Dilutable
 %Volatile (by Wt.) : 40 Max.
 Specific Gravity (Water – 1) : Greater than 1
 Evaporation Rate : Greater than 1
(Butyl Acetate = 1) P.4 of 6
10. STABILITY AND REACTIVITY

Stability : Stable
Conditions to Avoid : Temperature above 150C
Hazardous Decomposition : Not applicable
Products
Hazardous Polymerization : May occur
Incompatibility : Not applicable
(Materials to avoid)

11. TOXICOLOGICAL INFORMATION

No adverse health effects expected if the product is handled in accordance


with this Safety Data Sheet and the product label. Symptoms or effects that may
arise if the product is mishandled and overexposure occurs are :

Ingestion : no adverse effects expected, however, large amounts may


cause nausea and vomiting
Eye contact : may be eye irritant
Skin contact : may cause skin irritation
Inhalation : where this maerial is used in apoorly ventilated area, at
elevated temperatures or in confined spaces, vapour may cause irritation to
mucous membranes of respiratory tract, headache and nausea.

Long term effects : no information available

Toxicological Data : no LD50 data is available for this product

12. ECOLOGICAL INFORMATION

Ecotoxicity : avoid contaminating waterways

13. WASTE DISPOSAL METHOD


Incinerate the liquid and the contaminated diking material at permitted facility
according to local, state and Federal regulations.

5 of 6
14. TRANSPORT INFORMATION

Road and Rail Transport


Not classified as Dangerous Goods by the criteria of the Central Motor Vehicles
Rules 1989 as amended thereafter for transport by Road and Rail : NON-
DANGEROUS GOODS.

Marine Transport
Not classified as Dangerous Goods by the criteria of the International Maritime
Dangerous Goods Code (IMDG Code) for transport by sea; NON-DANGEROUS
GOODS.
Air Transport
Not classified as Dangerous Goods by the criteria of the International Air
Transport Association (IATA) Dangerous Goods Regulations for transport by air;
NON-DANGEROUS GOODS.

15. REGULATORY INFORMATION

Classification: The product requires a hazard-warning label.

EC supply labeling
S2 – keep out of the reach of the children
S26 – incase of contact with eyes, rinse immediately with plenty of water and
seek medical advice
S46 – if swallowed, seek immediate medical advice.

Poisons Schedule: None allocated.

16. OTHER INFORMATION


Titanium dioxide and inorganic filler when formulated, as above, do not pose
dust hazards unless sanding or grinding of the dry coating takes place.

The information contained in the Material Safety Data Sheet is based on data
considered accurate. However, no warranty is expressed or implied regarding
the accuracy of these data or the results to be obtained from the use thereof.
Recipients were advised to confirm in advance of need that the information is
correct, applicable and suitable to their circumstances.

P.6 of 6

You might also like