No.

SX-DSV03042

TECHNICAL REFERENCE
- Modbus communication
and Block operation Specification -

MOD E L
Product Name: AC Servo Driver
Product No.: MINAS-A6/A6L series

Issued on
Oct. 27, 2015
Revised on
Aug. 25, 2016

Motor Business Unit, Electromechanical Control Business Division

Automotive & Industrial Systems Company, Panasonic Corporation
7-1-1 Morofuku, Daito-City, Osaka 574-0044, Japan
Phone:+81-72-871-1212
Fax :+81-72-870-3151

R2.1
 No.SX-DSV03042

この英文仕様書は、原本である和文仕様書を元にパナソニック株式会社オートモーテ
ィブ＆インダストリアルシステムズ社モータビジネスユニットが翻訳・発行するもの
です。翻訳は，原本の利用に際して一応の参考となるように便宜的に仮訳したもので
あり、公的な校閲を受けたものではありません。英語訳のみを使用して生じた不都合
な事態に関しては，当社は一切責任を負うものではありません。和文仕様書のみが有
効です。
パナソニック株式会社
オートモーティブ＆インダストリアルシステムズ社 モータビジネスユニット

This English specification is made and published by Motor Business Unit

Automotive & Industrial Systems Company of Panasonic Corporation based
on the original Japanese specification. Translation is provided unofficially
only for the sake of convenience of utilizing the original Japanese
specification as a measure of reference. It is not officially reviewed. Motor
Business Unit Automotive & Industrial Systems Company of Panasonic
Corporation is not liable for any disadvantages caused by utilizing only
English specification. Only the Japanese specification is effective.
Motor Business Unit, Automotive & Industrial Systems Company,
Panasonic Corporation

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042

REVISIONS
Page
REVISION
Date Points changed Sym Signed
Dwg. No. changed Reason for change/contents of change

Oct. 27, 2015 - 1.0 NEWLY ISSUED

Software version upgrade CPU1 Ver 1.03 → Ver 1.05
Aug.01, 2016 P1 2.0
CPU2 Ver 1.03 → Ver 1.05
1) Infinite revolution absolute function
P34-36,59-64,66
2) External scale position information monitoring function under
- semi-closed control
3) Full-closed control support for load variance suppression function
-
4) Functional enhancement of quadrant projection suppression function
-
5) Position compare function
-
6) Serial absolute external scale Z-phase shift amount setting in pulse
- regeneration function
7) Slow stop function
-
8) Deterioration diagnosis warning function
-
9) Modbus function enhancements
P65 - Strobe input operation automatic OFF
P8-9,65 - Request action specification switching
P24,65 - Mirror register setting
10) Block operation function enhancements
P3,30,33,66 - Input signal start-up
P30,62-63 - Full close control support
P44,47,51 - Infinite length operation
P38,66 - Absolute mode correspondence to origin offset
Cover • Change Changed document title and issuing division

Cover • Addition Added A6L to Product number

P1 • Addition Added function comparison table

P7-10 • Correction Corrected contents of communication timing

P11-16 • Correction Corrected contents of Modbus data construction

P17-19 • Addition Added contents to coil information

P20-29 • Addition Added contents to register information

P33 • Addition Added contents to input and output signal assignment

P34 • Correction Corrected listing of wrap around threshold value

P37 • Addition Added setting method

P39 • Correction Corrected listing of Note *4)

P39 • Addition Added Note *4)

P46 • Addition Added explanation of target absolute position

(Note) Revised page numbers are those at the time of issue of the revised edition

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042

REVISIONS
Page
REVISION
Date Points changed Sym Signed
Dwg. No. changed Reason for change/contents of change

(Continued from previous page)

P48 • Addition Added explanation on drive prohibited input assignment

P48 • Correction Corrected contents of detection method

P50 • Addition Added explanation of command and Note *2).

P53 • Addition Added explanation on the contents of command argument

P55 • Addition Added remarks to comparison target “command velocity”

P57 • Addition Added start up method

P62 • Change Changed attribute of Err80.0

P62-63 • Addition Added Err97.0

P64 • Addition Added function and contents to P5.31

Software version upgrade CPU1 Ver 1.05 → Ver 1.06
P2 2.1
Aug. 25, 2016 CPU2 Ver 1.05 → Ver 1.06
1) “Main power supply AC Off detection time” Expansion of the set
- range
- 2) “Hybrid vibration suppression filter” Expansion of the set range
3) “Allowable motor operating range setting” Expansion of the
-
protection functions
4) “Block operation function” Specification improvement of
P50
Decelerate stop command

(Note) Revised page numbers are those at the time of issue of the revised edition

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042

Table of contents
1. Scope ............................................................................................................................................................................ 1
2. Summary ...................................................................................................................................................................... 3
2-1 Modbus communication specifications ................................................................................................................ 4
2-1-1 Connection to communication line ................................................................................................................. 4
2-1-2 Communication specifications ....................................................................................................................... 6
2-1-3 Communication timing ................................................................................................................................... 7
2-1-3-1 Normal communications ......................................................................................................................... 7
2-1-3-2 Broadcast communications (In case of using RS485) ............................................................................. 8
2-1-3-3 Abnormal communication..................................................................................................................... 10
2-1-4 Modbus data configuration ........................................................................................................................... 11
2-1-4-1 Command issue (Master station → Slave station) ................................................................................11
2-1-4-2 Function code details ........................................................................................................................... 13
2-1-4-3 Coil information ................................................................................................................................... 17
2-1-4-4 Register information ............................................................................................................................ 20
2-2 Basic specification of block operation functions ............................................................................................... 30
2-3 Initial setting and limitations .............................................................................................................................. 30
2-4 Set various stop sequce actions .......................................................................................................................... 31
2-5 Input/output signal assignment function for block operation ............................................................................. 33
2-6 Wraparound of command position ..................................................................................................................... 34
2-7 Initialization of absolute encoder ....................................................................................................................... 35
2-7-1 Absolute data ................................................................................................................................................ 35
2-7-2 Clearing multi-rotation data ......................................................................................................................... 36
3. Block parameters ........................................................................................................................................................ 37
3-1 Action set parameters ......................................................................................................................................... 37
3-2 Block data .......................................................................................................................................................... 39
3-2-1 Block [n]. command structure ...................................................................................................................... 39
3-2-2 Block [n]. data structure ............................................................................................................................... 39
3-2-3 Block data assignment .................................................................................................................................. 40
4. Commands ................................................................................................................................................................. 44
4-1 Command list ..................................................................................................................................................... 44
4-2 Relative positioning ........................................................................................................................................... 45
4-3 Absolute positioning .......................................................................................................................................... 46
4.4 Infinite length operation ..................................................................................................................................... 47
4-5 Return to origin .................................................................................................................................................. 48
4-6 Decelerate stop ................................................................................................................................................... 50
4-7 Renew velocity................................................................................................................................................... 51
4-8 Start decrement counter ..................................................................................................................................... 52
4-9 Output signal operation ...................................................................................................................................... 53
4-10 Jump ................................................................................................................................................................... 54
4-11 Conditional branch ............................................................................................................................................. 55
4-12 Block transition, start, and finish ....................................................................................................................... 57
4-12-1 Block transition conditions ........................................................................................................................... 57
4-12-2 Start and finish of block operation ............................................................................................................... 57
5. Block operation example ............................................................................................................................................ 58
6. Applied functions ....................................................................................................................................................... 59
6-1 Infinite rotation absolute function ...................................................................................................................... 59
7. Protection functions to detect when Modbus communication/block operation function is effective ......................... 62
7-1 List of protection functions to detect when Modbus communication/block operation function is effective ...... 62
7-2 Details of protection functions to detect when Modbus communication/block operation function is effective. 62
8. List of parameters ....................................................................................................................................................... 64

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 1 -

1. Scope

This technical document concerns the Modbus communication function specification and the block operation
function specifications for MINAS-A6/A6L series.

<MINAS-A6/A6L series Function comparison>

:Usable ×:Not usable
MINAS-A6 series
(Standard (Rotating type) Motor controlled type)
[A6SE] [A6SG] [A6SF]
Product
(Basic type) (RS485/RS232 (Multifunction type)
Function
Communication type)
Product number Product number Product number
ending with:E*** ending with:G*** ending with:F***

By Modbus 
× (Position control,
communication (Position control)
Block full-close control)
operation 
 
By input signal (Position control,
(Position control) (Position control)
full-close control)

MINAS-A6L series (Linea/DD motor control type)

- [A6SL] [A6SM]
Product (RS485/RS232 (Multifunction type)
Function Communication type)
Product number Product number
ending with:L*** ending with:M***
By Modbus  
-
Block communication (Position control) *1) (Position control) *1)
operation  
By input signal -
(Position control) *1) (Position control) *1)

*1) Block operation function cannot be used in case where the feedback scale is serial absolute rotary type.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 2 -

<Software version>
These materials apply to the servo-amplifiers of the following software versions:
CPU1 Version: Ver. 1.06
CPU2 Version: Ver. 1.06
* Please confirm the software version from the set-up support software (PANATERM) or from the front panel.

Software Functional change contents Corresponding

version PANATERM
CPU1 Ver 1.03 Initial release 6.0.0.2 or later
CPU2 Ver 1.03
CPU1 Ver 1.05 Function enhancement version 1 6.0.0.9 or later
CPU2 Ver 1.05 Additional function Related items
1) Infinite revolution absolute function 6-1
2) External scale position information monitoring
function under semi-closed control
3) Full-closed control support for load variance
suppression function
4) Functional enhancement of quadrant projection Technical reference
suppression function (Functional
5) Position compare function Specification)
6) Serial absolute external scale Z-phase shift amount
setting in pulse regeneration function
7) Slow stop function
8) Deterioration diagnosis warning function
9) Modbus function enhancements
- Strobe input operation automatic OFF 8
- Request action specification switching 8
- Mirror register setting 2-1-4, 8
10) Block operation function enhancements
- Input signal start-up 2, 8
- Full close control support 2-2
- Infinite length operation 4-1, 4-4
- Absolute mode correspondence to origin offset 3-1, 8

CPU1 Ver 1.06 Function enhancement version 2

CPU2 Ver 1.06 Additional function Related items
1) “Main power supply AC Off detection time” Technical reference
Expansion of the set range (Functional
2) “Hybrid vibration suppression filter” Expansion of Specification)
the set range
3) “Allowable motor operating range setting”
Expansion of the protection functions
4) “Block operation function” Specification 4-6
improvement of Decelerate stop command
- Eliminated the constraint in the case that
positioning action is not being executed.

* A new software version is downward compatible with a old software version.

Parameters used in a old software version can be used in a new software version, as is.

<Related materials>
SX-DSV03031: MINAS-A6 series Technical reference (Functional Specification)
SX-DSV*****: MINAS-A6L series Technical reference (Functional Specification)

<Points to note>
(1) Unauthorized copying or reproduction of all or a part of this document is strictly prohibited.
(2) The contents of this document (specification, software version, etc.) are subject to change without notice for
product improvement.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 3 -

2. Summary

In block operation, block programming positioning action is possible by the combination of a maximum of 256 block
commands.

In addition to the positioning commands, such as relative positioning, absolute positioning, return to origin command,
etc., the use of output signal operation, conditional branching and other commands is possible. Operation of output
signals and action pattern changes corresponding to the current motor positions and motor velocity can be easily
achieved by combining these commands.

The activation of these block operations can be selected either by Modbus communications or by an input signal
from the I/F connector.

The setting of block operation (block parameter setting) can be made by either of the two following methods:
• Block operation editor of the Set-up support software (PANATERM).
• Via Modbus communication (write register).

Relevant parameters
Set
Class No Parameter title Unit Functions, contents
range
Sets RS232/RS485 communications protocol.
0: MINAS standard protocol
5 37 Modbus connection setting 0 to 2 -
1: Modbus-RTU (RS232 communications, 1:1 only)
2: Modbus-RTU (RS485 communications, 1:N compatible)
Selects valid/invalid of block operation functions.
0: Block operations invalid
6 28 Special function select 0 to 2 -
1: Block operations via Modbus communications valid
2: Block operations by input signal valid

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 4 -

2-1 Modbus communication specifications

2-1-1 Connection to communication line

(1) In case of using RS232 physical layer:

Setting Pr 5.37 “Modbus connection setting” to 1, 1:1 connection Modbus communications by RS232
communication can be used.

Superior controller Servo driver

X2 SN751701
RS232 interface equivalent
4 RXD
TXD
3
RXD TXD
1
GND GND

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 5 -

(2) In case of using RS485 physical layer:

By setting Pr 5.37 “Modbus connection setting” to 2, 1: N connection Modbus communications by RS485
communication can be used.

Superior controller Servo driver

X2
RS485 interface ADM485 equivalent
6 RS485+
RS485+
5
RS485- RS485-
1
GND GND

8 RS485+
7 RS485-

Servo driver

X2
ADM485 equivalent
6 RS485+
5
RS485-
1
GND

8 RS485+
7 RS485-

Servo driver
X2
ADM485 equivalent
6
RS485+
5
RS485-
1
GND

8 RS485+
7 RS485-

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 6 -

2-1-2 Communication specifications

Protocol MODBUS-RTU (binary mode only)

Physical layer RS232 (1:1), RS485 (1:N, Max. 31 axis)
Baud rate *1 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 bps
Data 8 bit
Parity *2 None, even, odd (set to even at shipment)
Start bit 1 bit
Stop bit *2 1, 2 bit (set to 1 bit at shipment)

*1 Baud rate can be selected by Pr 5.29 “Set RS232 communication baud rate” when using RS232 and Pr
5.30 “Set RS485 communication baud rate” when using RS485.
*2 Parity and stop bit can be selected by Pr 5.38 “Set Modbus communications”.

Relevant parameters
Set
Class No Parameter title Unit Functions, contents
range
Set baud rate for RS232 communications.
0: 2400, 1: 4800, 2: 9600 3: 19200,
RS232 communications
5 29 0 to 7 - 4: 38400, 5: 57600, 6: 115200, 7: 230400 bps
baud rate setting *1
Note) In case it is not Modbus communications (Pr.5.37 = 0),
when value is set to 7, it will be set internally to 9600 bps.
Set baud rate for RS485 communications.
0: 2400, 1: 4800, 2: 9600 3: 19200,
RS485 communications
5 30 0 to 7 - 4: 38400, 5: 57600, 6: 115200, 7: 230400 bps
baud rate setting *1
Note) In case it is not Modbus communications (Pr.5.37 = 0),
when value is set to 7, it will be set internally to 9600 bps.
Sets parity (Even, odd, none) and stop bit length (1 bit, 2 bits)
for Modbus communications.
0: Even/1bit
Modbus communication 1: Even/2bit
5 38 0 to 5 -
setting 2: Odd/1bit
3: Odd/2bit
4: None/1bit
5: None/2bit

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 7 -

2-1-3 Communication timing

2-1-3-1 Normal communications

Relevant parameter
Set
Class No Parameter title Unit Functions, contents
range
Set waiting time to be added from the receipt of Modbus
Modbus response waiting 0 to communications request until response data is transmitted.
5 39 ms
Time 10000 Note) Even if value is set to 0, delay will occur for generation of
response data.

Silent interval

Master station command

T0
Slave station response
T1
T0 T0 T2 T0 or more T0
Line driver
Enable
(In case of using RS485)

T0: Silent interval time: (3.5 character lengths or 0.75ms, whichever is longer)
T1: Command processing time (will change in accordance with the command)
T2: Response waiting time (0 to 1000 ms)
Can be set by Pr5.39 “Modbus response waiting time”. Set to 0 ms at shipment.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 8 -

2-1-3-2 Broadcast communications (In case of using RS485)

The master station can broadcast commands simultaneously to multiple slave stations by setting 00h to the
slave address (broadcast command).

Slave stations receiving the broadcast command will operate as per the setting of Pr5.42 “Modbus broadcast
setting.”
(When Pr5.42 bit 1 =1, the slave station shall ignore the broadcast command and will not execute request
processing nor return a response.)

Relevant parameter
Set
Class No Parameter title Unit Functions, contents
range
Set waiting time to be added from the receipt of Modbus
Modbus response waiting 0 to communications request until response data is transmitted.
5 39 ms
Time 10000 Note) Even if value is set to 0, delay will occur for generation of
response data.
Sets time to detect Err 80.0 “Modbus communications time out
protection”, in case Modbus communications specifying own
Modbus communications 0 to axis or broadcast could not be received within the set length of
5 40 ms
Time out time 10000 time from the last time received, during the state where Modbus
execution rights are secured.
Err 80.0 not detected when set value is 0.
Sets request processing and response action, in case broadcast
mode request has been received in Modbus communications.
bit 0 response action
0: Invalid (No action) 1: Valid (Action) *1
bit 1: Request processing
0: Valid (Process) 1: Invalid (No processing)
bit 2: Strobe input operation automatic off
0: invalid, 1: valid *2
bit 3: Request operation specification switch *1
-32768 0: use Pr5.40, 1: Use Pr5.39
Modbus broadcast
5 42 to - bit 4 - 15: Not used Please set to 0 (zero).
Setting
32767
The lowermost bit is designated as bit 0.
*1 In case bit 3 = 0,
returns response after Pr5.31 × Pr5.40[ms].
In case bit 3 = 1,
returns response after Pr5.31 x Pr5.39 [ms].
Does not return response when bit 1 = 1.
*2 After start-up of block operation, strobe input operation will
be automatically turn OFF from the amplifier side. No need
to write input OFF.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 9 -

(1) When response operation is set to Invalid (Pr5.42 bit 0 = 0)

The slave station will not return a response.

- In case the number of slaves = 2:

Silent interval

Master station command

response
Slave station Axis number 1

T0
Axis number 2

T0 T3 T0

T0: Silent interval time: (3.5 character lengths or 0.75ms, whichever is longer)
T1: Command processing time (will change in accordance with the command)
T3: Broadcast command processing time
T3 ≥ T0+T1
Master station to transmit the next command after lapse of T3 period.

(2) When response operation is set to Valid (Pr5.42 bit0=1)

The slave station will not return a response.

When response operation is set to Valid
Each slave station will return a response in accordance with the timing indicated below, based on their
individual parameter settings.
Note that this specification is different from the standard Modbus specifications.

- In case the number of slaves = 2:

Silent interval Silent interval

Master station command

response
Slave station Axis number 1
T1
T0 T2×1 T0 or more

Axis number 2

T2×2 T2 or more
T0 T3 T0

T0: Silent interval time: (3.5 character lengths or 0.75ms, whichever is longer)
T1: Command processing time (will change in accordance with the command)
T2: Response waiting standard time (0 to 1000 ms)
Can be set by Pr5.40 “Modbus communications timeout time” when Pr5.42 bit 3 =0.
Can be set by Pr5.39 “Modbus response wait time” when Pr5.42 bit 3 =1.
Default setting is both set to 0 ms
Actual response wait time for each slave station shall be T2 × n, (n: axis number (Pr5.31))
T3: Broadcast command processing time
T3 ≥ T0 + T1 + T2 × (largest slave axis number + 1)
Master station to transmit the following command after lapse of T3

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 10 -

2-1-3-3 Abnormal communication

When the slave station fails to receive the command issued from the master station normally, it will ignore the
command and will not return a response.

• When a communications error is detected:

Abnormal communication generated

Master station command

Slave station
Not responding

Certain period of time

Using the timing charts of paragraphs 2-1-3-1 and 2-1-3-2 as reference, the master station shall judge time out
when response from the slave station is not received within a certain period of time.

Furthermore, the slave station can detect time out from the command receiving interval from the master station
by setting Pr5.40 “Modbus communication time out time.”

Relevant parameter
Set
Class No Parameter title Unit Functions, contents
range
Sets time to detect Err 80.0 “Modbus communications time out
protection”, in case Modbus communications specifying own
Modbus communications 0 to axis or broadcast could not be received within the set length of
5 40 ms
Time out time 10000 time from the last time received, during the state where Modbus
execution rights are secured.
Err 80.0 not detected when set value is 0.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 11 -

2-1-4 Modbus data configuration

2-1-4-1 Command issue (Master station → Slave station)

Slave address
(1 byte)
Function code
(1 byte)
Data
(0 to 252 bytes)
CRC
(2 bytes)

▪ Slave address

00h Broadcast address

01h to 7Fh Slave address

▪ Function code

Function code Function Contents

01h Read coil Read out coil information

03h Read register Read out registers for monitors, parameters, etc.
05h Write coil Write into the coil
06h Write register Write into the register
08h Communication diagnosis Loop back test
0Fh Write multiple coils Write into multiple coils
10h Write multiple registers Write into multiple registers

▪ Data
Will differ by function code.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 12 -

▪ CRC
CRC (Cyclic Redundancy Check) will be used for error check of Modbus-RTU.
Generating polynomial, CRC1-16(X16+X15+X2+1) will be used to produce the CRC code.

1. CRC production procedure

1) Set FFFFh as initial value of CRC.
2) Calculate XOR of the first byte data of command (Slave address) and CRC, and set its result on
CRC.
3) CRC to be shifted right by 1 bit.
4) In case the lowest digit bit overflow by the right shift in 3) is 0 (zero), go back to 3).
In case the lowest digit bit is 1, then calculate XOR of A001h and CRC, set the result on CRC
and return to 3).
5) Repeat 3) and 4) until 8 shifts have been performed.
6) Likewise, Repeat the process from 2) through 5) for the next byte in the command.
7) The value of the last CRC after repeating the command for the number of data bytes shall be the
CRC to be used for the error check.
8) When adding CRC to the end of the command, make sure that the lower bytes of the CRC comes
before the upper bytes (little-endian format)

2. Layout of CRC in the command

16-bit CRC in the command will be little-endian transmitted, with the lower bytes being transmitted
before the upper bytes.
An example where the value of CRC is 4321h is indicated as follows:

Slave address
(1 byte)
Function code
(1 byte)
Data
(0 to 252 bytes)
CRC (2 bytes) lower 21h
upper 43h

3. CRC error judgment

The value of CRC set by the host side is compared with the value of CRC recalculated from the command
date received by the driver side. If they do not match, received data will be discarded as CRC error.
And preparation will be made to receive the next transmission. (Will not go into an alarm state)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 13 -

2-1-4-2 Function code details

(1) Read coil (01h)

Transmission Reply Abnormal response
Slave address Slave address Slave address
01h 01h 81h
Coil start address Upper Number of data bytes (N) Exception code
Lower Data 1 CRC Lower
Number of coils Upper Data 2 Upper
Lower

---
CRC Lower
Upper Data N
CRC Lower
Upper

▪ Coil information for the number of coils set, counting from the address set as the coil start address, shall be sent
as a reply.
▪ For the number of data bytes (N), the quotient itself is returned in case there is no remainder when the number of
coils divided by 8, and “quotient + 1” in case there is a remainder.
▪ In case there is a remainder, the range off the specified coil number in the last data will be 0 (zero).
▪ Exception code 01h Abnormal function codes
02h Abnormal data address
03h Abnormal data
04h Abnormal response processing

(2) Read register (03h)

Transmission Reply Abnormal response
Slave address Slave address Slave address
03h 03h 83h
Register start address Upper Number of data bytes (N×2) Exception code
Lower Data 1 Upper CRC Lower
Number of register (N) Upper Lower Upper
Lower Data 2 Upper
CRC Lower Lower
Upper
---

Data N Upper
Lower
CRC Lower
Upper

▪ Returns register data for the number of registers specified, counting from the address set as the register start
address.
▪ Please set the address to read parameters and monitors for the register start address.
▪ Data is latched for every 10 data, inside the servo driver.
In case more than 10 read register numbers are to be acquired, the combination of data requiring synchronization
must be included within the same 10 data segment. (Example: Absolute 1 revolution data and multiple revolution
data)
▪ Exception code 01h Abnormal function codes
02h Abnormal data address
03h Abnormal data
04h Abnormal response processing

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 14 -

(3) Write coil (05h)

Transmission Reply Abnormal response
Slave address Slave address Slave address
05h 05h 85h
Address Upper Address Upper Exception code
Lower Lower CRC Lower
Changed data Upper Changed data N Upper Upper
Lower Lower
CRC Lower CRC Lower
Upper Upper

▪ Coil at the coil address specified is turned ON or OFF.

ON : Changed data upper FFh, lower 00h
OFF: Changed data upper 00h, lower 00h
▪ Exception code 01h Abnormal function codes
02h Abnormal data address
03h Abnormal data
04h Abnormal response processing

(4) Write register (06h)

Transmission Reply Abnormal response
Slave address Slave address Slave address
06h 06h 86h
Address Upper Address Upper Exception code
Lower Lower CRC Lower
Changed data Upper Changed data Upper Upper
Lower Lower
CRC Lower CRC Lower
Upper Upper

▪ Sets the value of changed data to the register specified as the address.
▪ Please set a valid address for the register start address.
• When writing servo parameters, use “Multiple register write (10h)” and not this function code.
▪ Exception code 01h Abnormal function codes
02h Abnormal data address
03h Abnormal data
04h Abnormal response processing

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 15 -

(5) Communication diagnosis (08h)

Transmission Reply Abnormal response
Slave address Slave address Slave address
08h 08h 88h
Diagnosis sub-code Upper Diagnosis sub-code Upper Exception code
Lower Lower CRC Lower
Data Upper Data Upper Upper
Lower Lower
CRC Lower CRC Lower
Upper Upper

▪ Diagnosis sub-code
upper 00h, lower 00h loop back test
Returns data transmitted from the host as is.
▪ Exception code 01h Abnormal function codes
03h Abnormal data
04h Abnormal response processing

(6) Write multiple coils (0Fh)

Transmission Reply Abnormal response
Slave address Slave address Slave address
0Fh 0Fh 8Fh
Start address Upper Start address Upper Exception code
Lower Lower CRC Lower
Number of coils Upper Number of coils Upper Upper
Lower Lower
Number of data bytes (N) CRC Lower
Changed data 1 Upper
Changed data 2
---

Changed data N Upper

CRC Lower
Upper

▪ Writes data for the number of coils, starting from the coil specified as the start address.
▪ For the number of data bytes (N), set the quotient itself in case there is no remainder when the number of coils
divided by 8, and “quotient + 1” in case there is a remainder.
▪ Changed data is set by the ON/OFF with 1-bit data (1/0) being assigned to each coil, starting from the coil
designated as the start address.
▪ Exception code 01h Abnormal function codes
02h Abnormal data address
03h Abnormal data
04h Abnormal response processing

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 16 -

(7) Write multiple registers (10h)

Transmission Reply Abnormal response
Slave address Slave address Slave address
10h 10h 90h
Start address Upper Start address Upper Exception code
Lower Lower CRC Lower
Number of registers (N) Upper Number of registers (N) Upper Upper
Lower Lower
Number of data bytes (N×2) CRC Lower
Changed data 1 Upper Upper
Lower
Changed data 2 Upper
Lower
---

Changed data N Upper

Lower
CRC Lower
Upper

▪ Writes data for the number of registers, starting from the register specified as the start address.
▪ Exception code 01h Abnormal function codes
02h Abnormal data address
03h Abnormal data
04h Abnormal response processing

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 17 -

2-1-4-3 Coil information

Address Coil name Attribute Contents
Physical input state monitor: Can monitor the physical input state of the input signal (SI1 to SI10)
0000h Input signal 1 (SI1) ReadOnly 0: Input OFF, 1: Input ON
0001h Input signal 2 (SI2) ReadOnly 0: Input OFF, 1: Input ON
0002h Input signal 3 (SI3) ReadOnly 0: Input OFF, 1: Input ON
0003h Input signal 4 (SI4) ReadOnly 0: Input OFF, 1: Input ON
0004h Input signal 5 (SI5) ReadOnly 0: Input OFF, 1: Input ON
0005h Input signal 6 (SI6) ReadOnly 0: Input OFF, 1: Input ON
0006h Input signal 7 (SI7) ReadOnly 0: Input OFF, 1: Input ON
0007h Input signal 8 (SI8) ReadOnly 0: Input OFF, 1: Input ON
0008h Input signal 9 (SI9) ReadOnly 0: Input OFF, 1: Input ON
0009h Input signal 10 (SI10) ReadOnly 0: Input OFF, 1: Input ON
Logic input state monitor: Can monitor each input state.
0020h Servo ON input (SRV-ON) ReadOnly 0: Input OFF, 1: Input ON
0021h Alarm clear input (A-CLR) ReadOnly 0: Input OFF, 1: Input ON
Negative direction drive prohibited input
0022h ReadOnly 0: Input OFF, 1: Input ON
(NOT)
0023h Positive direction drive prohibited input (POT) ReadOnly 0: Input OFF, 1: Input ON
0024h Control mode switching input (C-MODE) ReadOnly 0: Input OFF, 1: Input ON
0025h Zero velocity clamp input (ZEROSPD) ReadOnly 0: Input OFF, 1: Input ON
Command divider multiplier switching 1 input
0026h ReadOnly 0: Input OFF, 1: Input ON
(DIV1)
0027h Forced alarm input (E-STOP) ReadOnly 0: Input OFF, 1: Input ON
0028h Command pulse prohibited input (INH) ReadOnly 0: Input OFF, 1: Input ON
0029h Gain switching input (GAIN) ReadOnly 0: Input OFF, 1: Input ON
002Ah Clear counter input (CL) ReadOnly 0: Input OFF, 1: Input ON
002Bh For manufacturer use ReadOnly -
Inner velocity command select 1 input ReadOnly 0: Input OFF, 1: Input ON
002Ch
(INTSPD1)
Inner velocity command select 2 input ReadOnly 0: Input OFF, 1: Input ON
002Dh
(INTSPD2)
002Eh For manufacturer use ReadOnly -
002Fh For manufacturer use ReadOnly -
0030h For manufacturer use ReadOnly -
0031h For manufacturer use ReadOnly -
0032h Inertia ratio switching input (J-SEL) ReadOnly 0: Input OFF, 1: Input ON
Vibration damping control switching 1 input ReadOnly 0: Input OFF, 1: Input ON
0033h
(VS-SEL1)
Inner velocity command select 3 input ReadOnly 0: Input OFF, 1: Input ON
0034h
(INTSPD3)
0035h Torque limit switching input (TL-SEL) ReadOnly 0: Input OFF, 1: Input ON
Vibration damping control switching 2 input ReadOnly 0: Input OFF, 1: Input ON
0036h
(VS-SEL2)
Command divider multiplier switching 2 input ReadOnly 0: Input OFF, 1: Input ON
0037h
(DIV2)
0038h Velocity sign specifying input (VC-SIGN) ReadOnly 0: Input OFF, 1: Input ON
0039h Torque sign specifying input (TC-SIGN) ReadOnly 0: Input OFF, 1: Input ON
003Ah For manufacturer use ReadOnly -
003Bh Safety input 1 (SF1) ReadOnly 0: Input OFF, 1: Input ON
003Ch Safety input 2 (SF2) ReadOnly 0: Input OFF, 1: Input ON
003Dh For manufacturer use ReadOnly -
003Eh For manufacturer use ReadOnly -
003Fh For manufacturer use ReadOnly -

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 18 -

Address Coil name Attribute Contents

Logic input signal operation: ON, OFF of each input condition can be operated.
In case same function is assigned to I/F connector input, it will function as an OR with the state. (Except for servo-on (SRV-ON) input).
Servo ON input (SRV-ON) operation R/W 0000h: Input OFF, FF00h: Input ON
0060h In case servo-on (SRV-ON) is assigned to the I/F connector input, it will function as AND with the state. Release the I/F
connector input assignment to operate servo-on/off by this coil independently.
0061h Alarm clear input (A-CLR) operation R/W 0000h: Input OFF, FF00h: Input ON
0062h to 66h For manufacturer use R/W -
0067h Forced alarm input (E-STOP) operation R/W 0000h: Input OFF, FF00h: Input ON
0068h For manufacturer use R/W -
0069h Gain switching input (GAIN) operation R/W 0000h: Input OFF, FF00h: Input ON
006Ah to 71h For manufacturer use R/W -
0072h Inertia ratio switching input (J-SEL) operation R/W 0000h: Input OFF, FF00h: Input ON
Vibration damping control switching 1 input 0000h: Input OFF, FF00h: Input ON
0073h R/W
(VS-SEL1) operation
0074h For manufacturer use R/W -
Torque limit switching input (TL-SEL) 0000h: Input OFF, FF00h: Input ON
0075h R/W
operation
Vibration damping control switching 2 input 0000h: Input OFF, FF00h: Input ON
0076h R/W
(VS-SEL2) operation
0077h to 7Fh For manufacturer use R/W -
Physical output state monitor: Can monitor the physical output state of the output signal (SO1 to SO6)
0080h Output signal 1 (SO1) ReadOnly 0: Output OFF, 1: Output ON
0081h Output signal 2 (SO2) ReadOnly 0: Output OFF, 1: Output ON
0082h Output signal 3 (SO3) ReadOnly 0: Output OFF, 1: Output ON
0083h Output signal 4 (SO4) ReadOnly 0: Output OFF, 1: Output ON
0084h Output signal 5 (SO5) ReadOnly 0: Output OFF, 1: Output ON
0085h Output signal 6 (SO6) ReadOnly 0: Output OFF, 1: Output ON
Logic output state monitor: Can monitor each output state.
00A0h Servo ready state (S-RDY) ReadOnly 0: Ready OFF, 1: Ready ON
00A1h Alarm state (ALM) ReadOnly 0: Alarm not generated, 1: Alarm generated
00A2h Positioning complete state (INP) ReadOnly 0: Incomplete, 1: Complete
00A3h Mechanical brake release state (BRK-OFF) ReadOnly 0: Brake activated, 1: Brake released
00A4h Zero velocity detection state (ZSP) ReadOnly 0: Undetected, 1: Detected
00A5h Torque being limited state (TLC) ReadOnly 0: Unlimited, 1: limited
00A6h Velocity match detection state (V-COIN) ReadOnly 0: Undetected, 1: Detected
00A7h For manufacturer use ReadOnly -
00A8h For manufacturer use ReadOnly -
00A9h Reached velocity detection state (AT-SPEED) ReadOnly 0: Undetected, 1: Detected
00AAh For manufacturer use ReadOnly -
00ABh For manufacturer use ReadOnly -
00ACh For manufacturer use ReadOnly -
00ADh Dynamic brake activation state (DBRK) ReadOnly 0:DB OFF 1:DB ON
00AEh For manufacturer use ReadOnly -
00AFh Motor electrified state (FREE) ReadOnly 0: Electrified, 1: Not electrified
0: Warning 1 not generated state, 1: Warning 1 generated
00B0h Warning output 1 state (WARN1) ReadOnly
state
0: Warning 2 not generated state, 1: Warning 2 generated
00B1h Warning output 2 state (WARN2) ReadOnly
state
Positioning command with or without state 0: No positioning command, 1: With positioning command
00B2h ReadOnly
(P-CMD)
00B3h 2nd positioning complete state (INP2) ReadOnly 0: 2nd positioning incomplete, 1: 2nd positioning complete
00B4h Velocity being limited state (V-LIMIT) ReadOnly 0: No velocity limit, 1: Velocity being limited
00B5h Alarm attribute state (ALM-ATB) ReadOnly 0: Not clearable, 1: Clearable
Velocity command with or without state 0: No velocity command, 1: With velocity command
00B6h ReadOnly
(V-CMD)
00B7h Safety EDM state (O-EDM) ReadOnly 0:EDM OFF 1:EDM ON
00B8h to BFh For manufacturer use ReadOnly -

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 19 -

Address Coil name Attribute Contents

Motor activation state monitor: Able to monitor the activation state of the motor
0100h Torque being limited state ReadOnly 0: Torque not limited, 1: Torque being limited
0101h less than 30r/min detection state ReadOnly 0: 30r/min or higher, 1: less than 30 r/min
0102h In negative direction rotating state ReadOnly 0: Not in negative direction rotation, 1: In negative direction rotation.
0103h In positive direction rotating state ReadOnly 0: Not in positive direction rotation, 1: In positive direction rotation.
0104h For manufacturer use ReadOnly -
0105h For manufacturer use ReadOnly -
0106h For manufacturer use ReadOnly -
0107h For manufacturer use ReadOnly -
Block operation control operation: Enables control flags related to block operations to be operated.
In case the same functions are assigned to I/F connector input, it will function as an OR with the state.
0120h Strobe input (STB) operation R/W 0000h: Input OFF, FF00h: Input ON
0121h For manufacturer use R/W -
Vicinity of origin input (HOME) 0000h: Input OFF, FF00h: Input ON
0122h R/W
operation
Immediate stop input (H-STOP) 0000h: Input OFF, FF00h: Input ON
0123h R/W
operation
Decelerated stop input (S-STOP) 0000h: Input OFF, FF00h: Input ON
0124h R/W
operation
Block operation control monitor: Enables monitoring of control flags related to block operations.
0130h Strobe input (STB) state ReadOnly 0: Input OFF, 1: Input ON
0131h For manufacturer use ReadOnly -
Vicinity of origin sensor input 0: Input OFF, 1: Input ON
0132h ReadOnly
(HOME) state
Immediate stop input (H-STOP) 0: Input OFF, 1: Input ON
0133h ReadOnly
state
Decelerated stop input (S-STOP) 0: Input OFF, 1: Input ON
0134h ReadOnly
state
0138h For manufacturer use ReadOnly -
0139h For manufacturer use ReadOnly -
013Ah For manufacturer use ReadOnly -
013Bh For manufacturer use ReadOnly -
013Ch For manufacturer use ReadOnly -
013Dh For manufacturer use ReadOnly -
013Eh For manufacturer use ReadOnly -
013Fh For manufacturer use ReadOnly -
Block operation state monitor: Enables monitoring of block operation status.
Action implementation state 0: Not implemented, 1: Being implemented
0140h ReadOnly
(BUSY)
Returned to origin completed state 0: Incomplete, 1: Complete
0141h ReadOnly
(HOME-CMP)
Block operation output 1 0:OFF 1:ON
0142h ReadOnly
(B-CTRL1)
Block operation output 2 0:OFF 1:ON
0143h ReadOnly
(B-CTRL2)
Block operation output 3 0:OFF 1:ON
0144h ReadOnly
(B-CTRL3)
Block operation output 4 0:OFF 1:ON
0145h ReadOnly
(B-CTRL4)
Block operation output 5 0:OFF 1:ON
0146h ReadOnly
(B-CTRL5)
Block operation output 6 0:OFF 1:ON
0147h ReadOnly
(B-CTRL6)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 20 -

2-1-4-4 Register information

[Address in the 1000h order]

Number of
Address Register name Units Range Attribute Contents
register
Amplifier part number (16 characters)
Example) In case of “MADLT15SF”
Address 1000h = 414Dh ("AM")
Address 1001h = 4C44h ("LD")
Address 1002h = 3154h ("1T")
Address 1003h = 5335h ("S5")
1000h Manufacturer device name (ASCII) - 8 ReadOnly
Address 1004h = 0046h (NULL+"F")
Address 1005h = 0000h (NULL+NULL)
Address 1006h = 0000h (NULL+NULL)
Address 1007h = 0000h (NULL+NULL)
Note) The two characters inside one register are in reverse
order.
Amplifier software version (16 characters)
Example) In case of "V105.001.105.001”
Address 1010h = 3156h ("1V")
Address 1011h = 3530h ("50")
Address 1012h = 302Eh ("0.")
Manufacturer software Address 1013h = 3130h ("10")
1010h (ASCII) - 8 ReadOnly
version Address 1014h = 312Eh ("1.")
Address 1015h = 3530h ("50")
Address 1016h = 302Eh ("0.")
Address 1017h = 3130h ("10")
Note) The two characters inside one register are in reverse
order.
0 to Write parameter into EEPROM
1020h Save all parameters - 2 R/W
4294967295 Write EEPROM will be executed when “6173h” is written,
1030h Maximum messages - 0 to 255 1 ReadOnly 0Eh fixed
1031h Newest message - 0 to 255 1 ReadOnly Latest error history index
Newest acknowledged Clear error history
1032h - 0 to 255 1 R/W
message Clear error history will be executed when “0000h” is written,
Error history 1, Time of occurrence
Address 1038h = Time of error occurrence (lower 16 bit)
[0.5h]
Address 1039h = Time of error occurrence (upper 16 bit)
1038h Diagnosis message 1 - - 8 ReadOnly [0.5h]
Address 103Ah bit15 = For manufacturer use
bit14-8 = Error number (main)
bit7-0 = Error number (sub)
Address 103Bh-103Fh = For manufacturer use
1040h Diagnosis message 2 - - 8 ReadOnly Error history 2, Time of occurrence
1048h Diagnosis message 3 - - 8 ReadOnly Error history 3, Time of occurrence
1050h Diagnosis message 4 - - 8 ReadOnly Error history 4, Time of occurrence
1058h Diagnosis message 5 - - 8 ReadOnly Error history 5, Time of occurrence
1060h Diagnosis message 6 - - 8 ReadOnly Error history 6, Time of occurrence
1068h Diagnosis message 7 - - 8 ReadOnly Error history 7, Time of occurrence
1070h Diagnosis message 8 - - 8 ReadOnly Error history 8, Time of occurrence
1078h Diagnosis message 9 - - 8 ReadOnly Error history 9, Time of occurrence
1080h Diagnosis message 10 - - 8 ReadOnly Error history 10, Time of occurrence
1088h Diagnosis message 11 - - 8 ReadOnly Error history 11, Time of occurrence
1090h Diagnosis message 12 - - 8 ReadOnly Error history 12, Time of occurrence
1098h Diagnosis message 13 - - 8 ReadOnly Error history 13, Time of occurrence
10A0h Diagnosis message 14 - - 8 ReadOnly Error history 14, Time of occurrence

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 21 -

[Address in the 3000h order]

Addresses in the 3000h order are assigned to servo parameters (class 0 to 15).
Please refer to Technical Reference (Functional Specification) for details of servo parameters.

Address 3000h + (Class × 100h) + (No.× 2h)

Units As per servo parameter
Range As per servo parameter
Number of register 2
Attribute R/W

Example) Parameter for “Velocity feed forward gain”, class 1, No. 10; 3114h

3 1 14 h

No. × 2h (00h to FEh)

Class (0h to Fh)

• The number of registers for each servo parameter shall be 2, regardless of its range.
Always specify the address indicated above for the start address, with the number of registers set to 2, for write
or read. (Use “multiple register write (10h)” as the function code for write, not “register write (06h).”)

• Always execute read after write to confirm that the written data can be read.

• In the initial state, the contents to be read will be the parameter set value, but this can be changed by writing
values to the following registers.
Address 4210h “Servo parameter area output switching”
0000h: Parameter set value
0001h: Parameter minimum value
0002h: Parameter maximum value
0003h: Parameter attributes

• Write the value to the following register to save the set values of servo parameters to EEPROM.
Address 1020h “Save all parameters”
6173h: Execute writing EEPROM

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 22 -

[Address in the 4000h order]

Number of
Address Register name Units Range Attribute Contents
register
4000h Statusword1 - 0 to 65535 1 ReadOnly Amplifier state
Error number
main (1byte), sub (1byte)
4001h Error code - 0 to 65535 1 ReadOnly
Example) In case of Err26.0
1400h (main: 1Ah=26, sub: 00h=0)
Motor part number (16 characters)
Example) In case of MSMF022L2CMT
Address 4002h = 534Dh ("SM")
Address 4003h = 464Dh ("MF")
Address 4004h = 3230h ("20")
Address 4005h = 4C32h ("L2")
4002h Motor name - - 8 ReadOnly
Address 4006h = 4332h ("C2")
Address 4007h = 544Dh ("TM")
Address 4008h = 2020h (" ")
Address 4009h = 2020h (" ")
Note) The two characters in one register will be in
reverse order.
Motor serial number
Production year (1 byte), production month (1 byte),
serial number (2 bytes)
400Ah Motor serial number - 0 to 4294967295 2 ReadOnly
Example) When serial number is 14120001:
Address 400Ah = 0C0Eh (December, (20)14)
Address 400Bh = 0001h (serial No. = 0001)
400Ch Warning flag - 0 to 4294967295 2 ReadOnly Warning flag
400Eh Overload ratio % 0 to 500 1 ReadOnly Motor load rate
400Fh Regenerative load factor % -32768 to 32767 1 ReadOnly Regeneration load rate
Power supply on integrated -2147483648 to
4010h 0.5h 2 ReadOnly Aggregate power-on hours
time 2147483647
4012h Driver temperature °C -32768 to 32767 1 ReadOnly Servo driver temperature
Number of times of irruptive -2147483648 to
4013h Times 2 ReadOnly Number of rush resistor relay changing
resistance relay changing 2147483647
Number of times of dynamic -2147483648 to
4015h Times 2 ReadOnly Number of dynamic brake relay changing
brake relay changing 2147483647
4017h Fan operation time 0.5h 0 to 1000000 2 ReadOnly Fan operating hours
4019h Fan life time integrated value 0.1% 0 to 1000 1 ReadOnly Fan life integrated value
Condenser life time
401Ah 0.1% 0 to 1000 1 ReadOnly Capacitor life integrated value
integrated value
401Bh Encoder temperature °C -32768 to 32767 1 ReadOnly Encoder temperature
Command -2147483648 to
401Ch Velocity command value 2 ReadOnly Pre-filter command velocity
unit/s 2147483647
401Eh Velocity command value rpm -32768 to 32767 1 ReadOnly Position command velocity
401Fh Velocity command value rpm -32768 to 32767 1 ReadOnly Internal position command velocity
Command -2147483648 to
4020h Position command value 2 ReadOnly Post-filter command position
unit 2147483647
-2147483648 to
4022h Following error actual value pulse 2 ReadOnly Encoder position deviation
2147483647
4024h Velocity command value rpm -32768 to 32767 1 ReadOnly Velocity control command
4025h Velocity actual value rpm -32768 to 32767 1 ReadOnly Motor velocity
4026h Velocity limit value rpm -32768 to 32767 1 ReadOnly Velocity limit
Full close position following -2147483648 to
4027h pulse 2 ReadOnly Full close deviation
error 2147483647
Command -2147483648 to
4029h Hybrid following error 2 ReadOnly Hybrid deviation
unit 2147483647
Command -2147483648 to
402Bh Velocity command value 2 ReadOnly Post filter command velocity
unit/s 2147483647
(To be continued)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 23 -

Number of
Address Register name Unit Range Attribute Contents
register
Absolute multiturn data clear Absolute clear function
4100h - 0 to 65535 1 R/W
function Absolute clear will be executed when “6165h” is written,
Clear alarm and warning
4102h Trip reset function - 0 to 65535 1 R/W Alarm and warning clear will be executed when “7274h” is
written,
Encoder ID-L - 0 to 255 ReadOnly Encoder ID-L
4200h 1
Encoder ID-H - 0 to 255 ReadOnly Encoder ID-H
Encoder status-L - 0 to 255 ReadOnly Encoder status-L
4201h 1
Encoder status-H - 0 to 255 ReadOnly Encoder status-H
Encoder single turn data-L - 0 to 255 ReadOnly Encoder 1 rotation data-L
4202h Encoder single turn data-M - 0 to 255 2 ReadOnly Encoder 1 rotation data-M
Encoder single turn data-H - 0 to 255 ReadOnly Encoder 1 rotation data-H
Encoder multi turn data-L - 0 to 255 ReadOnly Encoder multi-rotation data-L
4204h 1
Encoder multi turn data-H - 0 to 255 ReadOnly Encoder multi-rotation data-H
External scale ID-L - 0 to 255 ReadOnly External scale ID-L
4208h 1
External scale ID-H - 0 to 255 ReadOnly External scale ID-H
External scale status-L - 0 to 255 ReadOnly External scale status-L
4209h 1
External scale status-H - 0 to 255 ReadOnly External scale status-H
External scale data (Lower
- 0 to 255 ReadOnly External scale data (lower 24 bit)-L
24bit)-L
External scale data (Lower
420Ah - 0 to 255 2 ReadOnly External scale data (lower 24-bit)-M
24bit)-M
External scale data (Lower
- 0 to 255 ReadOnly External scale data (lower 24-bit)-H
24bit)-H
External scale data (Upper
- ReadOnly External scale data (Upper 24 bit)-L
24bit)-L 0 to 255
External scale data (Upper
420Ch - 2 ReadOnly External scale data (Upper 24 bit)-M
24bit)-M 0 to 255
External scale data (Upper
- ReadOnly External scale data (Upper 24 bit)-H
24bit)-H 0 to 255
Servo parameter area output switching
0000h: Parameter set value
Servo parameter area output
4210h - 0 to 65535 1 R/W 0001h: Parameter minimum value
switching
0002h: Parameter maximum value
0003h: Parameter attributes
Set Modbus communication right *1
4300h mode - 0 to 255 1 R/W 55h: Acquire communication rights
AAh: Release communication rights
(To be continued)

*1) The servo amp will enter the following condition when Modbus communication right is acquired:
• All front panel operations cannot be used except for monitor mode (exclusive function)
• Err80.0 “Modbus communications time out protection” will be valid

Modbus communication right cannot be acquired if the front panel status is in “Execution indication,” other
than monitor mode.
(Refer to Technical Materials (Basic function specification edition) regarding the front panel.)

This register (4300h) cannot be set to Pr5.58 - 65, 79 - 86 “Modbus mirror register setting.”

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 24 -

Number of
Address Register name Unit Range Attribute Contents
register
4400h Physical input - 0 to 4294967295 2 ReadOnly Physical input state monitor (coil map)
4402h Logical input - 0 to 4294967295 2 ReadOnly Logic input state monitor (coil map)
4406h Virtual input - 0 to 4294967295 2 R/W Logic input signal operation (coil map)
4408h Physical output - 0 to 4294967295 2 ReadOnly Physical output state monitor (coil map)
440Ah Logical output - 0 to 4294967295 2 ReadOnly Logic output state monitor (coil map)
4410h Statusflag - 0 to 255 1 ReadOnly Motor activation state monitor (coil map)
4411h Block controlword - 0 to 65535 1 R/W Block operation control operation (coil map)
4412h Actual block controlword - 0 to 65535 1 ReadOnly Block operation control monitor (coil map)
4413h Block statusflag - 0 to 65535 1 ReadOnly Block operation state monitor (coil map)
4414h Block number - 0 to 65535 1 R/W Specify block number
4415h Actual block number - 0 to 65535 1 ReadOnly Actual block number
4416h Block number monitor - 0 to 65535 1 ReadOnly Currently valid block number
Write to Modbus register address set in Pr5.58 “Modbus
4418h Mirror register 1 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.59 “Modbus
4419h Mirror register 2 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.60 “Modbus
441Ah Mirror register 3 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.61 “Modbus
441Bh Mirror register 4 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.62 “Modbus
441Ch Mirror register 5 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.63 “Modbus
441Dh Mirror register 6 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.64 “Modbus
441Eh Mirror register 7 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.65 “Modbus
441Fh Mirror register 8 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.79 “Modbus
4420h Mirror register 9 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.80 “Modbus
4421h Mirror register 10 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.81 “Modbus
4422h Mirror register 11 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.82 “Modbus
4423h Mirror register 12 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.83 “Modbus
4424h Mirror register 13 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.84 “Modbus
4425h Mirror register 14 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.85 “Modbus
4426h Mirror register 15 - *3) 1 *3)
mirror register set 1” is enabled. *2)
Write to Modbus register address set in Pr5.86 “Modbus
4427h Mirror register 16 - *3) 1 *3)
mirror register set 1” is enabled. *2)
(To be continued)

*1) For the coil map, refer to the corresponding classifications in 2-1-4-3 “Coil information.”
The address configuration based on the leading address of the classification shall be the coil map.
Example: Coil 0067h “Forced alarm input (E-STOP) operation” in “Logic input signal operation” will
correspond to bit 7 of register 4406h “Logic input signal operation (coil map).”

*2) Read and write to Modbus register data set in PR5.58 to Pr5.65, and Pr5.79 to Pr5.86 is possible.
Address conversion of mirror register is effective only once. (Register address combining
multiple mirror registers cannot be set).
When address has been set for a mirror register, processing will be conducted as if a read or
writable register exists at the address. (Activity not affected)
Only register addresses between 1000h and in the 6000h range can be set with the mirror register
(no coil information can be set).

*3) The range and attribute of the mirror register shall be similar to the destination register.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 25 -

Number of
Address Register name Unit Range Attribute Contents
register
4600h Block velocity 0 r/min 0 to 20000 1 R/W Pr60.00 (Block operation velocity 0)
4601h Block velocity 1 r/min 0 to 20000 1 R/W Pr60.01 (Block operation velocity 1)
4602h Block velocity 2 r/min 0 to 20000 1 R/W Pr60.02 (Block operation velocity 2)
4603h Block velocity 3 r/min 0 to 20000 1 R/W Pr60.03 (Block operation velocity 3)
4604h Block velocity 4 r/min 0 to 20000 1 R/W Pr60.04 (Block operation velocity 4)
4605h Block velocity 5 r/min 0 to 20000 1 R/W Pr60.05 (Block operation velocity 5)
4606h Block velocity 6 r/min 0 to 20000 1 R/W Pr60.06 (Block operation velocity 6)
4607h Block velocity 7 r/min 0 to 20000 1 R/W Pr60.07 (Block operation velocity 7)
4608h Block velocity 8 r/min 0 to 20000 1 R/W Pr60.08 (Block operation velocity 8)
4609h Block velocity 9 r/min 0 to 20000 1 R/W Pr60.09 (Block operation velocity 9)
460Ah Block velocity 10 r/min 0 to 20000 1 R/W Pr60.10 (Block operation velocity 10)
460Bh Block velocity 11 r/min 0 to 20000 1 R/W Pr60.11 (Block operation velocity 11)
460Ch Block velocity 12 r/min 0 to 20000 1 R/W Pr60.12 (Block operation velocity 12)
460Dh Block velocity 13 r/min 0 to 20000 1 R/W Pr60.13 (Block operation velocity 13)
460Eh Block velocity 14 r/min 0 to 20000 1 R/W Pr60.14 (Block operation velocity 14)
460Fh Block velocity 15 r/min 0 to 20000 1 R/W Pr60.15 (Block operation velocity 15)
4610h Block accelaration 0 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.16 (Block operation acceleration 0)
4611h Block accelaration 1 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.17 (Block operation acceleration 1)
4612h Block accelaration 2 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.18 (Block operation acceleration 2)
4613h Block accelaration 3 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.19 (Block operation acceleration 3)
4614h Block accelaration 4 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.20 (Block operation acceleration 4)
4615h Block accelaration 5 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.21 (Block operation acceleration 5)
4616h Block accelaration 6 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.22 (Block operation acceleration 6)
4617h Block accelaration 7 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.23 (Block operation acceleration 7)
4618h Block accelaration 8 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.24 (Block operation acceleration 8)
4619h Block accelaration 9 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.25 (Block operation acceleration 9)
461Ah Block accelaration 10 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.26 (Block operation acceleration 10)
461Bh Block accelaration 11 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.27 (Block operation acceleration 11)
461Ch Block accelaration 12 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.28 (Block operation acceleration 12)
461Dh Block accelaration 13 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.29 (Block operation acceleration 13)
461Eh Block accelaration 14 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.30 (Block operation acceleration 14)
461Fh Block accelaration 15 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.31 (Block operation acceleration 15)
4620h Block decelaration 0 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.32 (Block operation deceleration 0)
4621h Block decelaration 1 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.33 (Block operation deceleration 1)
4622h Block decelaration 2 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.34 (Block operation deceleration 2)
4623h Block decelaration 3 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.35 (Block operation deceleration 3)
4624h Block decelaration 4 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.36 (Block operation deceleration 4)
4625h Block decelaration 5 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.37 (Block operation deceleration 5)
4626h Block decelaration 6 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.38 (Block operation deceleration 6)
4627h Block decelaration 7 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.39 (Block operation deceleration 7)
4628h Block decelaration 8 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.40 (Block operation deceleration 8)
4629h Block decelaration 9 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.41 (Block operation deceleration 9)
462Ah Block decelaration 10 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.42 (Block operation deceleration 10)
462Bh Block decelaration 11 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.43 (Block operation deceleration 11)
462Ch Block decelaration 12 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.44 (Block operation deceleration 12)
462Dh Block decelaration 13 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.45 (Block operation deceleration 13)
462Eh Block decelaration 14 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.46 (Block operation deceleration 14)
462Fh Block decelaration 15 ms/(3000 r/min) 0 to 10000 1 R/W Pr60.47 (Block operation deceleration 15)
4630h For manufacturer use - -32768 to 32767 1 R/W -
-2147483648 to
4631h Block home offset command unit 2 R/W Pr60.49 (Block operation origin offset)
2147483647
-2147483648 to Pr60.50 (Block operation positive direction software
4633h Block max position limit command unit 2 R/W
2147483647 limit)
-2147483648 to Pr60.51 (Block operation negative direction software
4635h Block min position limit command unit 2 R/W
2147483647 limit)
Pr60.52 (Block operation origin return velocity (high
4637h Block homing speed (high) r/min 0 to 20000 1 R/W
speed))
(To be continued)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 26 -

Number of Attribu
Address Register name Unit Range Contents
register te
Pr60.53 (Block operation origin return velocity (low
4638h Block homing speed (low) rpm 0 to 20000 1 R/W
speed))
ms
4639h Block homing accelaration 0 to 10000 1 R/W Pr60.54 (Block operation origin return acceleration)
/(3000 r/min)
463Ah Block homingless - 0 to 1 1 R/W Pr60.55 (Invalidate block operation origin return)
-2147483648 to
4800h Block command 0 - 2 R/W Pr56.000 (Block command 0)
2147483647
-2147483648 to
4802h Block data 0 - 2 R/W Pr56.001 (Block data 0)
2147483647
-2147483648 to
4804h Block command 1 - 2 R/W Pr56.002 (Block command 1)
2147483647
-2147483648 to
4806h Block data 1 - 2 R/W Pr56.003 (Block data 1)
2147483647
... ... ... ... ... ... ...
-2147483648 to
48FCh Block command 63 - 2 R/W Pr56.126 (Block command 63)
2147483647
-2147483648 to
48FEh Block data 63 - 2 R/W Pr56.127 (Block data 63)
2147483647
-2147483648 to
4900h Block command 64 - 2 R/W Pr57.000 (Block command 64)
2147483647
-2147483648 to
4902h Block data 64 - 2 R/W Pr57.001 (Block data 64)
2147483647
-2147483648 to
4904h Block command 65 - 2 R/W Pr57.002 (Block command 65)
2147483647
-2147483648 to
4906h Block data 65 - 2 R/W Pr57.003 (Block data 65)
2147483647
... ... ... ... ... ... ...
-2147483648 to
49FCh Block command 127 - 2 R/W Pr57.126 (Block command 127)
2147483647
-2147483648 to
49FEh Block data 127 - 2 R/W Pr57.127 (Block data 127)
2147483647
-2147483648 to
4A00h Block command 128 - 2 R/W Pr58.000 (Block command 128)
2147483647
-2147483648 to
4A02h Block data 128 - 2 R/W Pr58.001 (Block data 128)
2147483647
-2147483648 to
4A04h Block command 129 - 2 R/W Pr58.002 (Block command 129)
2147483647
-2147483648 to
4A06h Block data 129 - 2 R/W Pr58.003 (Block data 129)
2147483647
... ... ... ... ... ... ...
-2147483648 to
4AFCh Block command 191 - 2 R/W Pr58.126 (Block command 191)
2147483647
-2147483648 to
4AFEh Block data 191 - 2 R/W Pr58.127 (Block data 191)
2147483647
-2147483648 to
4B00h Block command 192 - 2 R/W Pr59.000 (Block command 192)
2147483647
-2147483648 to
4B02h Block data 192 - 2 R/W Pr59.001 (Block data 192)
2147483647
-2147483648 to
4B04h Block command 193 - 2 R/W Pr59.002 (Block command 193)
2147483647
-2147483648 to
4B06h Block data 193 - 2 R/W Pr59.003 (Block data 193)
2147483647
... ... ... ... ... ... ...
-2147483648 to
4BFCh Block command 255 - 2 R/W Pr59.126 (Block command 255)
2147483647
-2147483648 to
4BFEh Block data 255 - 2 R/W Pr59.127 (Block data 255)
2147483647
(To be continued)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 27 -

Number of
Address Register name Unit Range Attribute Contents
register
Position deviation (after -2147483648 to
4D00h pulse 2 Read Only Position deviation (after filter)
filter) 2147483647
-2147483648 to
4D02h Encoder resolution pulse/r 2 Read Only Encoder resolution
2147483647
-2147483648 to
4D06h Actual velocity r/min 2 Read Only Actual speed
2147483647
-2147483648 to
4D08h Torque command 0.05% 2 Read Only Torque command
2147483647
Velocity command (before -2147483648 to
4D0Ah r/min 2 Read Only Velocity command (before filter)
filter) 2147483647
Velocity command (after -2147483648 to
4D0Ch r/min 2 Read Only Velocity command (after filter)
filter) 2147483647
-2147483648 to
4D0Eh External scale position pulse 2 Read Only External scale position
2147483647
-2147483648 to
4D10h Regeneration load rate 0.1% 2 Read Only Regeneration load rate
2147483647
-2147483648 to
4D12h Overload load rate 0.2% 2 Read Only Overload load rate
2147483647
-2147483648 to
4D14h Enhanced logic input - 2 Read Only Enhanced logic input
2147483647
-2147483648 to
4D16h Enhanced logic output - 2 Read Only Enhanced logic output
2147483647
-2147483648 to
4D18h Physical input - 2 Read Only Physical input
2147483647
-2147483648 to
4D1Ah Physical output - 2 Read Only Physical output
2147483647
-2147483648 to
4D1Ch Inertia ratio % 2 Read Only Inertia ratio
2147483647
Motor automatic -2147483648 to
4D1Eh - 2 Read Only Motor automatic recognition effective state
recognition effective state 2147483647
-2147483648 to
4D20h Warning flag - 2 Read Only Warning flag
2147483647
-2147483648 to
4D22h Control mode - 2 Read Only Control mode
2147483647
Mechanical angle (Encoder -2147483648 to
4D24h pulse 2 Read Only Mechanical angle (Encoder 1 rotation data)
1 rotation data) 2147483647
-2147483648 to
4D26h Electrical angle 0.0879° 2 Read Only Electrical angle
2147483647
Multi-rotation data of -2147483648 to
4D28h R 2 Read Only Multi-rotation data of absolute encoder
absolute encoder 2147483647
-2147483648 to
4D2Ah Counter reference time 0.5h 2 Read Only Counter reference time
2147483647
Accumulated power on -2147483648 to
4D2Ch 0.5h 2 Read Only Accumulated power on time
time 2147483647
-2147483648 to
4D2Eh Alarm generated time 0.5h 2 Read Only Alarm generated time
2147483647
-2147483648 to
4D30h Amplifier temperature °C 2 Read Only Amplifier temperature
2147483647
-2147483648 to
4D32h Encoder temperature °C 2 Read Only Encoder temperature
2147483647
-2147483648 to
4D34h Fan operating time 0.5h 2 Read Only Fan operating time
2147483647
-2147483648 to
4D36h Integrated fan life hours 0.1% 2 Read Only Integrated fan life hours
2147483647
Capacitor life accumulated -2147483648 to
4D38h 0.1% 2 Read Only Capacitor life accumulated hours
hours 2147483647
Main power supply PN -2147483648 to
4D3Ah V 2 Read Only Main power supply PN voltage
voltage 2147483647
(To be continued)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 28 -

Number of
Address Register name Unit Range Attribute Contents
register
Encoder communication -2147483648 to
4D42h times 2 Read Only Encoder communication abnormal count
abnormal count 2147483647
External scale
-2147483648 to
4D46h communication abnormal times 2 Read Only External scale communication abnormal count
2147483647
count
Number of irruptive -2147483648 to
4D54h times 2 Read Only Number of irruptive resistance relay change
resistance relay change 2147483647
Number of dynamic brake -2147483648 to
4D56h times 2 Read Only Number of dynamic brake relay change
relay change 2147483647
-2147483648 to
4D5Ch Logic input - 2 Read Only Logic input
2147483647
-2147483648 to
4D5Eh Logic output - 2 Read Only Logic output
2147483647
External scale position
-2147483648 to External scale position (before command direction
4D60h(before command pulse 2 Read Only
2147483647 reversing)
direction reversing)
Deterioration diagnosis -2147483648 to
4DC0h - 2 Read Only Deterioration diagnosis state
state 2147483647
Average deterioration
-2147483648 to
4DC2h diagnosis torque 0.1% 2 Read Only Average deterioration diagnosis torque command value
2147483647
command value
Standard deterioration
-2147483648 to Standard deterioration diagnosis torque command
4DC4h diagnosis torque 0.1% 2 Read Only
2147483647 value
command value
Deterioration diagnosis -2147483648 to
4DC6h % 2 Read Only Deterioration diagnosis inertia ratio estimate
inertia ratio estimate 2147483647
Deterioration diagnosis -2147483648 to
4DC8h 0.1% 2 Read Only Deterioration diagnosis unbalanced load estimate
unbalanced load estimate 2147483647
Deterioration diagnosis -2147483648 to
4DCAh 0.1% 2 Read Only Deterioration diagnosis dynamic wear estimate
dynamic wear estimate 2147483647
Deterioration diagnosis 0.1%/ -2147483648 to
4DCCh 2 Read Only Deterioration diagnosis viscous friction estimate
viscous friction estimate (1000 r/min) 2147483647

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 29 -

[Address in the 6000h order]

Number of
Address Register name Unit Range Attribute Contents
register
6001h Error code - 0 to 65535 1 ReadOnly Read error No.
600Ah Modes of operation display - - 128 to 127 1 ReadOnly Amplifier internal control mode
-2147483648 to
600Bh Position demand value command unit 2 ReadOnly Pre-filter command position
2147483647
-2147483648 to
600Dh Position actual internal value pulse 2 ReadOnly Motor position (FB scale unit)
2147483647
-2147483648 to
600Fh Position actual value command unit 2 ReadOnly Motor position
2147483647
-2147483648 to
601Ah Velocity demand value command unit/s 2 ReadOnly Internal command velocity
2147483647
-2147483648 to
601Ch Velocity actual value command unit/s 2 ReadOnly Motor velocity
2147483647
6025h Torque demand 0.1% -32768 to 32767 1 ReadOnly Internal command torque
6026h Motor rated current mA 0 to 4294967295 2 ReadOnly Rated motor current
602Ch DC link circuit voltage mV 0 to 4294967295 2 ReadOnly Main power supply PN voltage
-2147483648 to
609Ch Following error actual value command unit 2 ReadOnly Position deviation
2147483647
-2147483648 to
609Eh Control effort command unit/s 2 ReadOnly Internal command velocity (output of position loop)
2147483647
Position demand internal -2147483648 to
60A0h pulse 2 ReadOnly Internal command position
value 2147483647
60A2h Digital inputs - 0 to 4294967295 2 ReadOnly External input signal monitor

*1) When using addresses in the 6000h range, set block operation to “Valid” (Pr 6.28 is non 0).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 30 -

2-2 Basic specification of block operation functions

Item Specification
Block processing cycle 1.0 [ms]
Number of blocks 256
Number of velocity set parameters 16
Number of acceleration set parameters 16
Number of deceleration set parameters 16
Activation method Modbus communications, input signal
Conditional branch Compatible (Jump, =, >, <)
Control mode Position control, full closed control
Origin return Compatible *1)
Renew velocity Compatible
Wrap around Compatible
Electronic gear Compatible
*1) By setting Pr. 60.55 “Set invalid block operation origin return” to 1 will enable positioning action to be
made without origin return even in increment mode.

2-3 Initial setting and limitations

In order to validate block operation functions by Modbus communications, it is necessary to set parameter Pr.
6.28 “Special function select” to 1 and Pr. 5.37 “Modbus connection setting” to either 1 or 2. In addition, to
activate block operation function, parameter Pr6.28 “Special function select” needs to be selected to 2.
In this case, analog and pulse I/F will become invalid.

Class No. Name Attribute Set value Command I/F Control mode
6 28 Special function Reclose 0 Analog/pulse input method Position/velocity/torque/full-closed
select power control
supply 1 Block operation method Position/full-closed control
by Modbus communications
2 Block operation method Position/full-closed control
by input signal

Set Pr.60.55 “Set invalid block operation origin return” to 1 to conduct relative positioning action or absolute
positioning action omitting origin return action under increment mode. In such a case, the position when the
power is reclosed shall become the origin (0).

Set Set
Class No. Parameter name Attribute Unit Contents
range value
60 55 Set invalid block 0 to 1 Reclose 0 Under increment mode, origin return action will be required
operation origin power prior to relative positioning or absolute positioning action is
return supply made.
- In absolute mode, origin return will not be required, regardless
of this setting.
1 Origin return action will not be required for both increment
mode and absolute mode.

Remarks) Increment mode: Position control mode where the current position at the time of power closing will
be the origin (0). (Pr0.15 = 1)
Absolute mode: Position control mode where the current position at the time of power closing is
referenced by the position memorized by the absolute encoder. (Pr0.15 = non 1)

Please set the block parameter prior to starting the block operation. Please refer to Chapter 3 for details of block
parameters.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 31 -

2-4 Set various stop sequce actions

When block operation functions are validated, the following specifications shall apply for stop sequence in case
of drive prohibited, servo OFF, main power supply OFF and alarm.
Furthermore, slow stop function (Refer to Technical reference (Functional Specification) 6-5-7) cannot be used
when block operation is valid.

▪ Sequence at drive prohibited

Decelerating (30 r/min or greater) After stop (30 r/min or less)
Internal position
Pr5.04 Pr5.05 Internal position
command Command after
Stop method Deviation Deviation command generation
generation stop
/ Block operation
/ Block operation
Restarting block
Torque command
operation will validate
Dynamic brake for drive Maintain
0 0, 1, 2 Clear Forced stop action only in reverse
action prohibited *1)
direction to the drive
direction = 0.
prohibited direction.*2)

(Note) Origin return is not dependent on the value of Pr.5.05 “(Sequence at drive prohibited). Please refer
to paragraph 4-5 for details.
*1) In case drive prohibited input is detected while in action at 30 r/min or less, deviation will be
temporarily cleared at the detection timing.
*2) Block operation will be forced stop, in case drive prohibited input is detected while in action at 30
r/min or less.
Please note that internal position command will be generated in where the torque command is 0
(zero) and block operation has been restarted against the drive prohibited direction.

▪ Sequence at servo OFF

Decelerating (30 r/min or greater) After stop (30 r/min or less)
Internal position
Pr5.06 Internal position
command Command after
Stop method Deviation Deviation command generation
generation stop
/ Block operation
/ Block operation
Dynamic brake Dynamic brake
0, 4 Clear Forced stop Clear Forced stop
action action
Dynamic brake
1, 5 Free run Clear Forced stop Clear Forced stop
action
Dynamic brake
2, 6 Clear Forced stop Free run Clear Forced stop
action
3, 7 Free run Clear Forced stop Free run Clear Forced stop
Dynamic brake
8 Immediate stop*3) Maintain Forced stop Clear Forced stop
action
9 Immediate stop*3) Maintain Forced stop Free run Clear Forced stop

*3) In case of immediate stop, torque limit shall be in accordance with the set value of Pr 5.11
(Immediate stop torque limit).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 32 -

▪ Sequence at main power supply OFF

Decelerating (30 r/min or greater) After stop (30 r/min or less)
Internal position
Pr5.07 Internal position
command Command after
Stop method Deviation Deviation command generation
generation stop
/ Block operation
/ Block operation
Dynamic brake Dynamic brake
0,4 Clear Forced stop Clear Forced stop
action action
Dynamic brake
1,5 Free run Clear Forced stop Clear Forced stop
action
Dynamic brake
2,6 Clear Forced stop Free run Clear Forced stop
action
3,7 Free run Clear Forced stop Free run Clear Forced stop
Immediate stop Dynamic brake
8 Maintain Forced stop Clear Forced stop
*4) action
Immediate stop
9 Maintain Forced stop Free run Clear Forced stop
*4)

*4) In case of immediate stop, torque limit shall be in accordance with the set value of Pr 5.11
(Immediate stop torque limit).

▪ Sequence at alarm
Decelerating (30 r/min or greater) After stop (30 r/min or less)
Internal position
Pr5.10 Internal position
command Command after
Stop method Deviation Deviation command generation
generation stop
/ Block operation
/ Block operation
Dynamic brake Dynamic brake
0 Clear Forced stop Clear Forced stop
action action
Dynamic brake
1 Free run Clear Forced stop Clear Forced stop
action
Dynamic brake
2 Clear Forced stop Free run Clear Forced stop
action
3 Free run Clear Forced stop Free run Clear Forced stop
Immediate
Action A
stop Maintain
*5) Dynamic brake
4 *6) Forced stop Clear Forced stop
action
Action B
DB action Clear
*5)
Immediate
Action A
stop Maintain
*5) Dynamic brake
5 *6) Forced stop Clear Forced stop
action
Action B
Free run Clear
*5)
Immediate
Action A
stop Maintain
*5)
6 *6) Forced stop Free run Clear Forced stop
Action B
DB action Clear
*5)
Immediate
Action A
stop Maintain
*5)
7 *6) Forced stop Free run Clear Forced stop
Action B
Free run Clear
*5)

*5) Actions A and B indicates whether to trigger immediate stop when errors occur. When immediate
stop supported alarm has been activated, in case the set value is from 4 to 7, action A will be taken
and will stop immediately. In case immediate stop unsupported alarm has been activated, it will not
stop immediately, but dynamic brake (DB) action or free run, specified in action B, will be taken.
Please maintain the main circuit power supply until it decelerates and stops.
Please refer to the Technical Reference (Basic function specifications) for immediate stop
supporting alarms.
*6) In case of immediate stop, torque limit shall be in accordance with the set value of Pr 5.11
(Immediate stop torque limit).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 33 -

2-5 Input/output signal assignment function for block operation

For input/output signals, arbitrary function used for block operation can be assigned to any input/output pin of I/F
connector. To use function that relevant to block operation, for instance origin input (HOME) or returned to
origin completed state output (HOME-CMP) , Pr4.00~Pr4.09 and Pr4.10~Pr4.15 need to be changed and assigned
to each of the pins. Function numbers that relevant to block operation are as following.

Input function number for block operation table

Input signal assignment Corresponding Modbus
Signal name Symbol Pr4.00 to 4.09 Setup value coil/register
a-contact b-contact
Origin input HOME 21h A1h Block 0122h
Immediate stop input H-STOP 22h A2h operation 0123h
Decelerated stop input S-STOP 23h A3h control 0124h
Strobe input STB 24h A4h operation 0120h
Designated block number input 1 B-SEL 1 25h A5h
Designated block number input 2 B-SEL 2 26h A6h
Designated block number input 4 B-SEL 4 27h A7h
Designated block number input 8 B-SEL 8 28h A8h 4414h
Designated block number input 16 B-SEL 16 29h A9h “Block number”
Designated block number input 32 B-SEL 32 2Ah AAh
Designated block number input 64 B-SEL 64 2Bh ABh
Designated block number input 128 B-SEL 128 2Ch ACh

Output function number for block operation table

Output signal assignment Corresponding Modbus coil
Signal name Symbol
Pr4.10 to 4.15 Setup value
Action implementation state output BUSY 21h 0140h
Returned to origin completed state
HOME-CMP 22h 0141h
output
Block
Block operation output 1 B-CTRL1 23h 0142h
operation
Block operation output 2 B-CTRL2 24h 0143h
control
Block operation output 3 B-CTRL3 25h 0144h
operation
Block operation output 4 B-CTRL4 26h 0145h
Block operation output 5 B-CTRL5 27h 0146h
Block operation output 6 B-CTRL6 28h 0147h

Please refer to the Technical Reference (Functional specifications) for detail of input/output signal assignment.

[When block operation by Modbus communication start is valid (Pr6.28 =1)]

• I/F connector input and Modbus coil (Logic input signal operation/block operation control operation) will
function in OR. However, servo on input (SRV-ON) will function as AND for the I/F connector input and
Modbus coil (0060h). In case servo on input is not assigned to the I/F connector input, servo on/off will be
operated only by the Modbus coil (0060h).
• Modbus register 4414h “Block number” is used to designate block numbers (0 to 255). (Designated block
number input is invalid)

[When block operation by start by input signal is effective (Pr6.28 = 2)]

• Use designated block number input to designate block numbers (0 to 255). In order to designate all 256
blocks, it is necessary to allocate all 8 signals of B-SEl1 to B-SEl128 as input signals. The method to
designate block numbers are as follows:
Block number bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
Designated block
B-SEL 128 B-SEL 64 B-SEL 32 B-SEL 16 B-SEL 8 B-SEL 4 B-SEL 2 B-SEL 1
number input
(Example) To designate Block number 145 B-SEL 1, B-SEl 16 and B-SEL 128 must be turned ON.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 34 -

2-6 Wraparound of command position

Wrap around processing will be activated when the amount of change of the command position exceeds the
following values:
Command position range [Command unit] Wraparound threshold
Absolute encoder setting
Lower limit Upper limit [Command unit]
Infinite rotation absolute (223×(set value for Pr6.88 +1) (223×(set value for Pr6.88 +1)
0
mode *1) / Electronic gear ratio) -1 / Electronic gear ratio) / 2
Other than infinite rotation 80000000h 7FFFFFFFh 7FFFFFFFh
absolute mode (-2147483648) (2147483647) (2147483647)
*1) Please refer to 6-1 for infinite rotation absolute mode.

Example of wraparound processing

When absolute target position has changed from 7FFFFFFFh to 80000000h in Infinite rotation
absolute mode.

Servo internal computation

Command position (command unit)

1 [command unit] transfer

in positive direction
4294967295 [command 7FFFFFFFh (wraparound processing)
unit] to negative direction
No relative transfer

Physical
position

80000000h 80000000h

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 35 -

2-7 Initialization of absolute encoder

*This shall not apply to MINAS-A6L Series ([A6SL]/[A6SM]).

When using the absolute encoder under position control mode, return to origin operation will not be required
(with the exception where the absolute encoder is to be used under increment mode). However, the
multi-rotation data must be cleared during initialization for the first start-up after installation of the batteries.

2-7-1 Absolute data

Data read out from the absolute encoder (23 bits/r) consists of the single rotation data that indicate the position
inside one motor rotation, and the multi-rotation data that counts from 1 up for every motor rotation. Of these, the
multi-rotation data is an electric counter and is backed up by batteries.
Both data has a polarity that increases with CCW rotation.
Whether to generate Err41.0 “Absolute counter overflow error protection” in case the multi-rotation data has
overflowed can be selected by parameter Pr0.15 “Absolute encoder setting.”

Back up when power supply has

Data width Code Data range
been shut off
Single rotation data Not required 23 bit None 0 to 8388607
Multi-rotation data Battery back-up 16 bit Yes 0 to 65535 (max) *1)
*1) In the infinite rotation absolute mode, the upper limit can be set by Pr6.68 “Absolute multi-rotation upper
limit.”
Set to 65535 (maximum value) for setting other than infinite rotation absolute mode.
Please refer to 6-1 for infinite rotation absolute mode.

When power is switched on, the servo amplifier will set the motor position based on the following formula:

With the 23 bit absolute encoder, single rotation data is 23 bits, while the multi-rotation data is 16 bits, and the
synthesized actual location will have a 39 bit width. Of this, only the lower 32 bits will be returned to the
upstream equipment as the motor position. As a result, the upmost 7 bits out of 16 bits of the multi-rotation data is
lost and its effective bit length will become 9 bits.

Parameter Pr0.00 Motor position

APOS: Actual_Position
“Set rotating direction” *1)
Motor position
If 1, M: Multi-turn_Data
23bit APOS = M×223＋S+OFS
(CCW in positive direction) Multi-rotation data
If 0, S: Single-turn_Data
23bit APOS = -(M×223＋S)+OFS Single rotation data
(CW in positive direction)
OFS: Pr60.49
*1) Calculation formula when the electronic gear ratio is 1:1.
Block operation origin offset
When setting the electronic gear, keep it to fit within a signed 32
bit width.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 36 -

Motor position
CCW direction (when CCW is in the positive direction)

Single rotation data

223-1

Position
0

n
n-1
*1)
n-2
n-3 Multi-rotation data

3
2
1
Position
0
Range where multi-rotation data has been cleared

*1) The value of n shall be as follows:

Infinite rotation absolute mode: n = Value set for Pr6.88
Other than infinite rotation absolute mode: n = 65535

2-7-2 Clearing multi-rotation data

When multi-rotation data is cleared, the point of variation of multi-rotation data on the CW side of the position
where the clear was made, shall become the actual position “0.” To prevent devisation when setting, plseas
conduct “clear” in a position that is farthest away from the point of variation of multi-rotation data, where the one
rotation data is 222 (for 23 bits/r).

<Points to note to prevent unnecessary troubles>

When clearing multi-rotation data, please turn off the servo, immobilize it with a brake, etc., if
required, and secure safety before taking any action
Maintain the servo in OFF state during the operation, and after completion, first turn off all
control power supply, and then reclose the power supply

Use set-up support software PANATERM (via USB communication ) or Modbus communication to clear the
multi-rotation data. *2)
When multi-rotation data is cleared, Err27.1 “Absolute clear error protection” will occur. This is a safety feature
and is not an abnormality.

*2) Write values into the following register to clear multi-rotation data via Modbus communication.
Address 4100h “Absolute multiturn data clear function“
6165h：Execute absolute clear

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 37 -

3. Block parameters

This chapter lists the parameters related to block operation. These parameters must be set before activating the block
operations. No guarantees can be made for the action due to the block operation related parameters changed after
activation of block operation.

Unexpected action may occur as a result of errors in the setting of block operation commands and data, etc. The
customer is requested to carry out fail-safe design and to secure safety within its operating range at the location of use.

Block parameters can be set by either of the following methods:

• Set-up support software (PANATERM)

Selecting “Other”  “Block operation editor” from the tool bar will enable the editing of block data
(Classifications 56 to 59) and operation setting (Classification 60) in their respective dedicated screens. Clicking
on the block number to be edited will indicate the edit screen.

• Via Modbus communications

Use Modbus function code “Write register (06h)” or “Write multiple registers (10h)” to write date into registers
4600h to 4BFFh (block parameter domain).
Please refer to 2-1-4-2 for details of the function codes and 2-1-4-4 for details of the registers.

3-1 Action set parameters

Classification No Name Attribute Size Contents

. [bit]
60 0 Block operation velocity [0] Always 16 Able to provide 16 types of block operation velocity.
1 Block operation velocity [1] effective
Units: [r/min]
2 Block operation velocity [2] *1)
Set range: 0 to 20000 *2) *3)
3 Block operation velocity [3]
4 Block operation velocity [4]
5 Block operation velocity [5] Sets value of 1 to the arguments for relative
6 Block operation velocity [6] positioning, absolute positioning, and velocity update
7 Block operation velocity [7] command.
8 Block operation velocity [8] The number set inside the brackets ([ ]) of the
9 Block operation velocity [9] parameter name (velocity number) shall be set for the
10 Block operation velocity [10]
argument 1 of each command, and not the parameter
11 Block operation velocity [11]
12 Block operation velocity [12] No.
13 Block operation velocity [13]
14 Block operation velocity [14]
15 Block operation velocity [15]
16 Block operation acceleration setting [0] Always 16 Able to provide 16 types of acceleration.
17 Block operation acceleration setting [1] effective
Units: [ms]
18 Block operation acceleration setting [2] *1)
Set range: 0 to 10000 *3) *4)
19 Block operation acceleration setting [3]
20 Block operation acceleration setting [4]
21 Block operation acceleration setting [5] To be set to acceleration time of 0 to 3000 [r/min].
22 Block operation acceleration setting [6]
23 Block operation acceleration setting [7]
24 Block operation acceleration setting [8]
25 Block operation acceleration setting [9]
26 Block operation acceleration setting [10]
27 Block operation acceleration setting [11]
28 Block operation acceleration setting [12]
29 Block operation acceleration setting [13]
30 Block operation acceleration setting [14]
31 Block operation acceleration setting [15]

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 38 -

Classification No. Name Attribute Size Contents

[bit]
60 32 Block operation deceleration setting [0] Always 16 Able to provide 16 types of deceleration.
33 Block operation deceleration setting [1] effective Units: [ms]
34 Block operation deceleration setting [2] *1) Set range: 0 to 10000 *3) *4)
35 Block operation deceleration setting [3]
To be set to deceleration time of 3000 to 0 [r/min].
36 Block operation deceleration setting [4]
37 Block operation deceleration setting [5]
38 Block operation deceleration setting [6]
39 Block operation deceleration setting [7]
40 Block operation deceleration setting [8]
41 Block operation deceleration setting [9]
42 Block operation deceleration setting
[10]
43 Block operation deceleration setting
[11]
44 Block operation deceleration setting
[12]
45 Block operation deceleration setting
[13]
46 Block operation deceleration setting
[14]
47 Block operation deceleration setting
[15]
48 Block operation method setting Reclose 16 Sets origin offset valid/invalid for absolute mode.
power bit :0: used by manufacturer:
supply Set fixed to 0
bit 1: Origin offset under absolute mode
0: invalid, 1: valid
bit 2 -15: Not used, Set fixed to 0

The lowermost bit is bit 0.

49 Block operation origin Reclose 32 Sets offset amount of origin when origin return is
offset power completed in block operation, under increment mode.
supply Sets the amount of offset between the encoder
position in block operation and the machine
coordinate position under absolute mode. Becomes
valid when Pr60.48 (Block operation method setting)
bit 1 is set to 1.
50 Block operation Reclose 32 Set range of software limit when origin return is
positive direction software limit power completed in block operation.
supply
51 Block operation Reclose 32 Set range of software limit when origin return is
negative direction software limit power completed in block operation.
supply
52 Block operation Reclose 16 Sets high action velocity for origin return.
origin return velocity (high speed) power Units: [r/min]
supply Set range: 0 to 20000 *2) *3)
53 Block operation Reclose 16 Sets low action velocity for origin return.
origin return velocity (low speed) power Units: [r/min]
supply Set range: 0 to 20000 *2) *3)
54 Block operation Reclose 16 Sets acceleration and deceleration for origin return
origin return acceleration and power action.
deceleration supply Units: [ms]
Set range: 0 to 10000 *3) *4)
To be set for duration from 0 to 3000 [r/min].
55 Invalidate block operation origin return Reclose 16 Set to 1 to conduct relative positioning action or
power absolute positioning action without returning to origin
supply under increment mode.
Set range: 0 to 1

0: Under increment mode, origin return action will

be required prior to relative positioning or
absolute positioning action is made.
In absolute mode, origin return will not be
required, regardless of this setting.
1: Origin return action will not be required for both
increment mode and absolute mode.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 39 -

*1) Although the attribute is always effective, there are no guarantees for changes made while block operation is
activated. To be always set before block operation. Always stop the block operation first, before changing
values.
*2) Block related velocity data, as a parameter set value, may be set up to a maximum of 20,000, however, the
internal data will be limited to the maximum velocity of the motor.
*3) If 0 (zero) is set for velocity, acceleration time, and deceleration time when block operation is activated, Err.
93.1 (block data setting abnormal protection) will be triggered.
*4) When acceleration or deceleration velocity exceeds 4294967295 [command units/s2], Err93.1 “Block data
setting error protection” will be triggered .
*5) Please set the block operation positive direction soft limit with a value larger than the block operation
negative direction soft limit.
Furthermore, the value for block operation origin offset must be set to a value equal or larger than block
operation negative direction soft limit but equal or smaller than block operation positive direction soft limit..

3-2 Block data

Block data is comprised of 64 bits of data per block, and is separated into 32 bit command region
(block[n].command) and 32 bit data region (block[n].data).
(Note) Value in [ ] denotes the block number.

These block data are assigned to parameters (classifications 56 through 59) and must be set before the start of
block operation.
Contents of block data will differ with each command. Please refer to Chapter 4 for details.

3-2-1 Block [n]. command structure

bit 7 6 5 4 3 2 1 0
byte
0 (Reserved)
1 Argument 3 Argument 4 Argument 5
2 Argument 1 Argument 2
3 Command code

3-2-2 Block [n]. data structure

bit 7 6 5 4 3 2 1 0
byte
0 LL
1 LH
Argument 7
2 HL
3 HH

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 40 -

3-2-3 Block data assignment

Although the attribute is always effective, there are no guarantees for changes made while block operation is
activated. To be always set before block operation. Always stop the block operation first, before changing values.
Classifi- No. Name Attribute Size Classifi- No. Name Attribute Size
cation [bit] cation [bit]
56 000 Block[0].command Always 32 56 064 Block[32].command Always 32
001 Block[0].data effective 32 065 Block[32].data effective 32
002 Block[1].command 32 066 Block[33].command 32
003 Block[1].data 32 067 Block[33].data 32
004 Block[2].command 32 068 Block[34].command 32
005 Block[2].data 32 069 Block[34].data 32
006 Block[3].command 32 070 Block[35].command 32
007 Block[3].data 32 071 Block[35].data 32
008 Block[4].command 32 072 Block[36].command 32
009 Block[4].data 32 073 Block[36].data 32
010 Block[5].command 32 074 Block[37].command 32
011 Block[5].data 32 075 Block[37].data 32
012 Block[6].command 32 076 Block[38].command 32
013 Block[6].data 32 077 Block[38].data 32
014 Block[7].command 32 078 Block[39].command 32
015 Block[7].data 32 079 Block[39].data 32
016 Block[8].command 32 080 Block[40].command 32
017 Block[8].data 32 081 Block[40].data 32
018 Block[9].command 32 082 Block[41].command 32
019 Block[9].data 32 083 Block[41].data 32
020 Block[10].command 32 084 Block[42].command 32
021 Block[10].data 32 085 Block[42].data 32
022 Block[11].command 32 086 Block[43].command 32
023 Block[11].data 32 087 Block[43].data 32
024 Block[12].command 32 088 Block[44].command 32
025 Block[12].data 32 089 Block[44].data 32
026 Block[13].command 32 090 Block[45].command 32
027 Block[13].data 32 091 Block[45].data 32
028 Block[14].command 32 092 Block[46].command 32
029 Block[14].data 32 093 Block[46].data 32
030 Block[15].command 32 094 Block[47].command 32
031 Block[15].data 32 095 Block[47].data 32
032 Block[16].command 32 096 Block[48].command 32
033 Block[16].data 32 097 Block[48].data 32
034 Block[17].command 32 098 Block[49].command 32
035 Block[17].data 32 099 Block[49].data 32
036 Block[18].command 32 100 Block[50].command 32
037 Block[18].data 32 101 Block[50].data 32
038 Block[19].command 32 102 Block[51].command 32
039 Block[19].data 32 103 Block[51].data 32
040 Block[20].command 32 104 Block[52].command 32
041 Block[20].data 32 105 Block[52].data 32
042 Block[21].command 32 106 Block[53].command 32
043 Block[21].data 32 107 Block[53].data 32
044 Block[22].command 32 108 Block[54].command 32
045 Block[22].data 32 109 Block[54].data 32
046 Block[23].command 32 110 Block[55].command 32
047 Block[23].data 32 111 Block[55].data 32
048 Block[24].command 32 112 Block[56].command 32
049 Block[24].data 32 113 Block[56].data 32
050 Block[25].command 32 114 Block[57].command 32
051 Block[25].data 32 115 Block[57].data 32
052 Block[26].command 32 116 Block[58].command 32
053 Block[26].data 32 117 Block[58].data 32
054 Block[27].command 32 118 Block[59].command 32
055 Block[27].data 32 119 Block[59].data 32
056 Block[28].command 32 120 Block[60].command 32
057 Block[28].data 32 121 Block[60].data 32
058 Block[29].command 32 122 Block[61].command 32
059 Block[29].data 32 123 Block[61].data 32
060 Block[30].command 32 124 Block[62].command 32
061 Block[30].data 32 125 Block[62].data 32
062 Block[31].command 32 126 Block[63].command 32
063 Block[31].data 32 127 Block[63].data 32

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 41 -

Classifi- No. Name Attribute Size Classifi- No. Name Attribute Size
cation [bit] cation [bit]
57 000 Block[64].command Always 32 57 064 Block[96].command Always 32
001 Block[64].data effective 32 065 Block[96].data effective 32
002 Block[65].command 32 066 Block[97].command 32
003 Block[65].data 32 067 Block[97].data 32
004 Block[66].command 32 068 Block[98].command 32
005 Block[66].data 32 069 Block[98].data 32
006 Block[67].command 32 070 Block[99].command 32
007 Block[67].data 32 071 Block[99].data 32
008 Block[68].command 32 072 Block[100].command 32
009 Block[68].data 32 073 Block[100].data 32
010 Block[69].command 32 074 Block[101].command 32
011 Block[69].data 32 075 Block[101].data 32
012 Block[70].command 32 076 Block[102].command 32
013 Block[70].data 32 077 Block[102].data 32
014 Block[71].command 32 078 Block[103].command 32
015 Block[71].data 32 079 Block[103].data 32
016 Block[72].command 32 080 Block[104].command 32
017 Block[72].data 32 081 Block[104].data 32
018 Block[73].command 32 082 Block[105].command 32
019 Block[73].data 32 083 Block[105].data 32
020 Block[74].command 32 084 Block[106].command 32
021 Block[74].data 32 085 Block[106].data 32
022 Block[75].command 32 086 Block[107].command 32
023 Block[75].data 32 087 Block[107].data 32
024 Block[76].command 32 088 Block[108].command 32
025 Block[76].data 32 089 Block[108].data 32
026 Block[77].command 32 090 Block[109].command 32
027 Block[77].data 32 091 Block[109].data 32
028 Block[78].command 32 092 Block[110].command 32
029 Block[78].data 32 093 Block[110].data 32
030 Block[79].command 32 094 Block[111].command 32
031 Block[79].data 32 095 Block[111].data 32
032 Block[80].command 32 096 Block[112].command 32
033 Block[80].data 32 097 Block[112].data 32
034 Block[81].command 32 098 Block[113].command 32
035 Block[81].data 32 099 Block[113].data 32
036 Block[82].command 32 100 Block[114].command 32
037 Block[82].data 32 101 Block[114].data 32
038 Block[83].command 32 102 Block[115].command 32
039 Block[83].data 32 103 Block[115].data 32
040 Block[84].command 32 104 Block[116].command 32
041 Block[84].data 32 105 Block[116].data 32
042 Block[85].command 32 106 Block[117].command 32
043 Block[85].data 32 107 Block[117].data 32
044 Block[86].command 32 108 Block[118].command 32
045 Block[86].data 32 109 Block[118].data 32
046 Block[87].command 32 110 Block[119].command 32
047 Block[87].data 32 111 Block[119].data 32
048 Block[88].command 32 112 Block[120].command 32
049 Block[88].data 32 113 Block[120].data 32
050 Block[89].command 32 114 Block[121].command 32
051 Block[89].data 32 115 Block[121].data 32
052 Block[90].command 32 116 Block[122].command 32
053 Block[90].data 32 117 Block[122].data 32
054 Block[91].command 32 118 Block[123].command 32
055 Block[91].data 32 119 Block[123].data 32
056 Block[92].command 32 120 Block[124].command 32
057 Block[92].data 32 121 Block[124].data 32
058 Block[93].command 32 122 Block[125].command 32
059 Block[93].data 32 123 Block[125].data 32
060 Block[94].command 32 124 Block[126].command 32
061 Block[94].data 32 125 Block[126].data 32
062 Block[95].command 32 126 Block[127].command 32
063 Block[95].data 32 127 Block[127].data 32

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 42 -

Classifi- No. Name Attribute Size Classifi- No. Name Attribute Size
cation [bit] cation [bit]
58 000 Block[128].command Always 32 58 064 Block[160].command Always 32
001 Block[128].data effective 32 065 Block[160].data effective 32
002 Block[129].command 32 066 Block[161].command 32
003 Block[129].data 32 067 Block[161].data 32
004 Block[130].command 32 068 Block[162].command 32
005 Block[130].data 32 069 Block[162].data 32
006 Block[131].command 32 070 Block[163].command 32
007 Block[131].data 32 071 Block[163].data 32
008 Block[132].command 32 072 Block[164].command 32
009 Block[132].data 32 073 Block[164].data 32
010 Block[133].command 32 074 Block[165].command 32
011 Block[133].data 32 075 Block[165].data 32
012 Block[134].command 32 076 Block[166].command 32
013 Block[134].data 32 077 Block[166].data 32
014 Block[135].command 32 078 Block[167].command 32
015 Block[135].data 32 079 Block[167].data 32
016 Block[136].command 32 080 Block[168].command 32
017 Block[136].data 32 081 Block[168].data 32
018 Block[137].command 32 082 Block[169].command 32
019 Block[137].data 32 083 Block[169].data 32
020 Block[138].command 32 084 Block[170].command 32
021 Block[138].data 32 085 Block[170].data 32
022 Block[139].command 32 086 Block[171].command 32
023 Block[139].data 32 087 Block[171].data 32
024 Block[140].command 32 088 Block[172].command 32
025 Block[140].data 32 089 Block[172].data 32
026 Block[141].command 32 090 Block[173].command 32
027 Block[141].data 32 091 Block[173].data 32
028 Block[142].command 32 092 Block[174].command 32
029 Block[142].data 32 093 Block[174].data 32
030 Block[143].command 32 094 Block[175].command 32
031 Block[143].data 32 095 Block[175].data 32
032 Block[144].command 32 096 Block[176].command 32
033 Block[144].data 32 097 Block[176].data 32
034 Block[145].command 32 098 Block[177].command 32
035 Block[145].data 32 099 Block[177].data 32
036 Block[146].command 32 100 Block[178].command 32
037 Block[146].data 32 101 Block[178].data 32
038 Block[147].command 32 102 Block[179].command 32
039 Block[147].data 32 103 Block[179].data 32
040 Block[148].command 32 104 Block[180].command 32
041 Block[148].data 32 105 Block[180].data 32
042 Block[149].command 32 106 Block[181].command 32
043 Block[149].data 32 107 Block[181].data 32
044 Block[150].command 32 108 Block[182].command 32
045 Block[150].data 32 109 Block[182].data 32
046 Block[151].command 32 110 Block[183].command 32
047 Block[151].data 32 111 Block[183].data 32
048 Block[152].command 32 112 Block[184].command 32
049 Block[152].data 32 113 Block[184].data 32
050 Block[153].command 32 114 Block[185].command 32
051 Block[153].data 32 115 Block[185].data 32
052 Block[154].command 32 116 Block[186].command 32
053 Block[154].data 32 117 Block[186].data 32
054 Block[155].command 32 118 Block[187].command 32
055 Block[155].data 32 119 Block[187].data 32
056 Block[156].command 32 120 Block[188].command 32
057 Block[156].data 32 121 Block[188].data 32
058 Block[157].command 32 122 Block[189].command 32
059 Block[157].data 32 123 Block[189].data 32
060 Block[158].command 32 124 Block[190].command 32
061 Block[158].data 32 125 Block[190].data 32
062 Block[159].command 32 126 Block[191].command 32
063 Block[159].data 32 127 Block[191].data 32

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 43 -

Classifi- No. Name Attribute Size Classifi- No. Name Attribute Size
cation [bit] cation [bit]
59 000 Block[192].command Always 32 59 064 Block[224].command Always 32
001 Block[192].data effective 32 065 Block[224].data effective 32
002 Block[193].command 32 066 Block[225].command 32
003 Block[193].data 32 067 Block[225].data 32
004 Block[194].command 32 068 Block[226].command 32
005 Block[194].data 32 069 Block[226].data 32
006 Block[195].command 32 070 Block[227].command 32
007 Block[195].data 32 071 Block[227].data 32
008 Block[196].command 32 072 Block[228].command 32
009 Block[196].data 32 073 Block[228].data 32
010 Block[197].command 32 074 Block[229].command 32
011 Block[197].data 32 075 Block[229].data 32
012 Block[198].command 32 076 Block[230].command 32
013 Block[198].data 32 077 Block[230].data 32
014 Block[199].command 32 078 Block[231].command 32
015 Block[199].data 32 079 Block[231].data 32
016 Block[200].command 32 080 Block[232].command 32
017 Block[200].data 32 081 Block[232].data 32
018 Block[201].command 32 082 Block[233].command 32
019 Block[201].data 32 083 Block[233].data 32
020 Block[202].command 32 084 Block[234].command 32
021 Block[202].data 32 085 Block[234].data 32
022 Block[203].command 32 086 Block[235].command 32
023 Block[203].data 32 087 Block[235].data 32
024 Block[204].command 32 088 Block[236].command 32
025 Block[204].data 32 089 Block[236].data 32
026 Block[205].command 32 090 Block[237].command 32
027 Block[205].data 32 091 Block[237].data 32
028 Block[206].command 32 092 Block[238].command 32
029 Block[206].data 32 093 Block[238].data 32
030 Block[207].command 32 094 Block[239].command 32
031 Block[207].data 32 095 Block[239].data 32
032 Block[208].command 32 096 Block[240].command 32
033 Block[208].data 32 097 Block[240].data 32
034 Block[209].command 32 098 Block[241].command 32
035 Block[209].data 32 099 Block[241].data 32
036 Block[210].command 32 100 Block[242].command 32
037 Block[210].data 32 101 Block[242].data 32
038 Block[211].command 32 102 Block[243].command 32
039 Block[211].data 32 103 Block[243].data 32
040 Block[212].command 32 104 Block[244].command 32
041 Block[212].data 32 105 Block[244].data 32
042 Block[213].command 32 106 Block[245].command 32
043 Block[213].data 32 107 Block[245].data 32
044 Block[214].command 32 108 Block[246].command 32
045 Block[214].data 32 109 Block[246].data 32
046 Block[215].command 32 110 Block[247].command 32
047 Block[215].data 32 111 Block[247].data 32
048 Block[216].command 32 112 Block[248].command 32
049 Block[216].data 32 113 Block[248].data 32
050 Block[217].command 32 114 Block[249].command 32
051 Block[217].data 32 115 Block[249].data 32
052 Block[218].command 32 116 Block[250].command 32
053 Block[218].data 32 117 Block[250].data 32
054 Block[219].command 32 118 Block[251].command 32
055 Block[219].data 32 119 Block[251].data 32
056 Block[220].command 32 120 Block[252].command 32
057 Block[220].data 32 121 Block[252].data 32
058 Block[221].command 32 122 Block[253].command 32
059 Block[221].data 32 123 Block[253].data 32
060 Block[222].command 32 124 Block[254].command 32
061 Block[222].data 32 125 Block[254].data 32
062 Block[223].command 32 126 Block[255].command 32
063 Block[223].data 32 127 Block[255].data 32

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 44 -

4. Commands

4-1 Command list

Blockdata [n] (64bit)

Command Data
Command name Command
Argument 1 Argument 2 Argument 3 Argument 4 Argument 5 Argument 6 Argument 7
code
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Acceleration Deceleration Block (Reserved) Relative travel
Relative Velocity
01h setting setting - transition amount
positioning number
number number condition [command unit]
Acceleration Deceleration Block (Reserved) Target absolute
Absolute Velocity
02h setting setting - transition position
positioning number
number number condition [command unit]
Acceleration Deceleration Block (Reserved)
Infinite length Velocity Operating
03h setting setting transition --
operation number direction
number number condition
Block (Reserved)
Detection Origin return
Origin return 04h - - transition -
method direction
condition
Block (Reserved)
Stop
Decelerate stop 05h - - - transition -
method
condition
Operating Block (Reserved)
Velocity
Renew velocity 06h - - direction transition -
number
*1) condition
Block (Reserved) Counter set
Decrement
07h - - - - transition value
counter start
condition [1ms]
Block (Reserved)
Output signal B-CTRL1 B-CTRL3 B-CTRL5
08h - transition -
operation B-CTRL2 B-CTRL4 B-CTRL6
condition
Block (Reserved)
Jump 09h - Block No. (destination) transition -
condition
Block (Reserved)
Conditional For Compared value
0Ah Block No. (destination, if Yes)) transition
branch (=) comparison (threshold)
condition
Block (Reserved)
Conditional For Compared value
0Bh Block No. (destination, if Yes)) transition
branch (>) comparison (threshold)
condition
Block (Reserved)
Conditional For Compared value
0Ch Block No. (destination, if Yes)) transition
branch (<) comparison (threshold)
condition

*1) Only effective in case of infinite length operation.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 45 -

4-2 Relative positioning

Command Code : 1h
Used in case of conducting relative positioning action.
Blockdata [n] (64bit)
Command Data
Command name Command
Argument 1 Argument 2 Argument 3 Argument 4 Argument 5 Argument 6 Argument 7
code
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Acceleration Deceleration Block (Reserved) Relative travel
Relative Velocity
01h setting setting - transition amount
positioning number
number number condition [command unit]

Velocity
Block operation Block operation
[r/min]
Acceleration Deceleration
setting [y] setting [z]

Block operation
Velocity [x]

3000

Relative travel amount

Time

Start position = X Stop position = X + relative travel amount

Command argument Set range Contents

1 Velocity number 0 to 15 Set selection number x for block operation velocity [x].
2 Acceleration 0 to 15 Set selection number y for block operation acceleration setting [y].
setting number
3 Deceleration 0 to 15 Set selection number z for block operation deceleration setting [z].
setting number
4 - - Please set to 0 (zero).
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0: Transitions to next block after start.
1: Transitions to next block after completion of positioning. *1)
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 Relative travel 80000001h Relative travel amount to be set by command units.
amount to 7FFFFFFFh
(-2147483647
to 2147483647)

Parameter Set range Unit Contents

Block operation velocity 0 to maximum [r/min] Sets velocity
[x] motor velocity
Block operation 0 to 10000 [ms] Sets acceleration
acceleration setting [y] To be set at acceleration time of 0 to 3000 [r/min].
Block operation 0 to 10000 [ms] Sets deceleration
deceleration setting [z] To be set at deceleration time of 3000 to 0 [r/min].

*1) “After completion of positioning” shall mean the point when internal positioning command generation
processing has ended. It is not judged by the actual stopping of the motor. Furthermore, please note that
movement command will be issued even if the internal positioning command generation processing has
ended, in case position command filter (FIR, smoothing) is being used.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 46 -

4-3 Absolute positioning

Command Code : 2h
Used in case of conducting absolute positioning action.

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument Argument Argument Argument
Argument 7
code 1 2 3 4 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Acceleration Deceleration Block (Reserved) Target absolute
Absolute Velocity
02h setting setting - transition position
positioning number
number number condition [command unit]

Velocity
Block operation Block operation
[r/min]
acceleration deceleration
setting [y] setting [z]

Block operation
velocity [x]

3000

Amount of travel = Target absolute position – X

*2)
Time

Start position = X Stop position = Target absolute position

Command argument Set range Contents

1 Velocity number 0 to 15 Set selection number x for block operation velocity [x].
2 Acceleration 0 to 15 Set selection number y for block operation acceleration setting [y].
setting number
3 Deceleration 0 to 15 Set selection number z for block operation deceleration setting [z].
setting number
4 - - Please set to 0 (zero).
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0: Transitions to next block after start.
1: Transitions to next block after completion of positioning. *1)
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 Target absolute 80000000h Sets target absolute position (with sign) in command units.
position to 7FFFFFFFh In case the amount of travel is set to 80000000h (2147483648), it will be operated as 0
(-2147483648 (zero) amount of travel, and if set in excess of 80000000h (2147483648), wrap around
to 2147483647) processing will be enabled. (Refer to 2-6)

Parameter Set range Unit Contents

Block operation velocity 0 to maximum [r/min] Sets velocity
[x] motor velocity
Block operation 0 to 10000 [ms] Sets acceleration
acceleration setting [y] To be set at acceleration time of 0 to 3000 [r/min].
Block operation 0 to 10000 [ms] Sets deceleration
deceleration setting [z] To be set at deceleration time of 3000 to 0 [r/min].

*1) “After completion of positioning” shall mean the point when internal positioning command generation processing has ended. It is not
judged by the actual stopping of the motor. Furthermore, please note that movement command will be issued even if the internal
positioning command generation processing has ended, in case position command filter (FIR, smoothing) is being used.
*2) Case where warp around is not performed.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 47 -

4.4 Infinite length operation

Command code: 3h

Used for infinite length operation.

Block data [n] (64 bits)

Command Data
Command
name Command
Argument 1 Argument 2 Argument 3 Argument 4 Argument 5 Argument 6 Argument 7
code
8 bits 4 bits 4 bits 4 bits 2 bits 2 bits 8 bits 32 bits
Infinite Acceleratio Deceleratio Block
Velocity Operation
length 03h n setting n setting transition (Reserved) －
number direction
operation number number condition

Velocity
Block operation Block operation
[r/min]
acceleration setting [y] deceleration setting [z]

Block operation
velocity [x]

3000

Time

Start position Stop position

Setting
Command argument Contents
range
1 Velocity number 0 - 15 Sets selected number x for block operation velocity [x]
2 Acceleration setting number 0 - 15 Sets selected number y for block operation acceleration set [y].
3 Deceleration setting number 0 - 15 Sets selected number z for block operation deceleration set [z].
4 Operation direction 0-1 0: positive direction, 1: negative direction
Sets block transition condition after execution of this command:
[LSB] 0, 1: Transitions to next block after booting
5 Block transition condition 0-3
[MSB] 0: Ends block operation with this block.
1: Continues with the block operation
6 - - Please set to 0
7 - - Please set to 0

Parameter Setting range Units Contents

0 - Maximum
block operation velocity [x] [rpm] Sets velocity
motor velocity
Sets acceleration,
block operation acceleration set
0 - 10000 [ms] Setting conducted in acceleration time range of 0 to 3000
[y].
[r/min]
Sets deceleration
block operation deceleration set
0 - 10000 [ms] Setting conducted in deceleration time range of 3000 to 0
[z].
[r/min]
*1) Please use either of the two following methods to stop infinite length operation. (Entering block number for deceleration and stop
command in strobe input operation will not stop the operation).
[1] Immediate stop and decelerated stop by immediate stop input/decelerated stop input:
(In case of decelerated stop by decelerated stop input, stop will be made in accordance with the block operation deceleration setting
[z], specified by the set deceleration umber.)
[2] Immediate stop and decelerated stop by combination of conditional branch command and decelerated stop command:

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 48 -

4-5 Return to origin

Command Code : 4h
Used in case of conducting origin return action.
In the case of increment mode, there is a need to conduct origin return action. However, by setting Pr.60.55 “Set
invalid block operation origin return” to 1, origin return action can be omitted. In such a case, the position when the
power is reclosed shall become the origin (0).
In case origin return command is executed in absolute mode, Err 94.2 “Origin return abnormal protection” will occur.
In addition, there is a need to assign a generic input (SIn) as vicinity of origin input (HOME) and connect the origin
sensor in advance. Furthermore, there is a need to connect the limit sensor (prohibited drive input) in advance and
assign general input (SIn) to positive direction prohibited drive input (POT) and negative direction prohibited drive
input (NOT).
In case using detection method is 2, SI4 only can be assigned to origin input (HOME), (if any other pins are assigned,
Err 94.2 “Origin return error protection” will occur). A noise canceling filter process is conducted in the read-out of
the input signal. Please set so that the sensor signal width is 4 ms or wider. Furthermore, in case detection method is
1, in order to prevent detection error, please arrange so that the time from the leading edge reference detection of the
vicinity of origin input (HOME) to the Z phase is 10 ms or larger.
In case there are problems in installing the vicinity of origin input (HOME) and limit sensor (drive prohibited input),
Err 94.2 “Origin return abnormal protection” will occur.
When drive prohibited input in origin return direction is turned ON during origin return action, please note that
regardless of the value of Pr 5.05 “Sequence at drive prohibited”, reverse action still under servo-ON state will be
executed. When the drive prohibited input for origin return direction is turned ON and the drive prohibited input for
the direction opposite to the origin return direction being turned ON while it is in reverse action, Err 94.2 “Origin
return abnormal protection” will occur.
Origin return action velocity shall be as per Pr 60.52 “Block operation origin return velocity (high speed)” or Pr
60.53 “Block operation origin return velocity (low speed). Acceleration shall be as per Pr 60.54 “Block
operation origin return acceleration and deceleration”.

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument Argument Argument Argument
Argument 7
code 1 2 3 4 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Origin Block (Reserved)
Detection
Origin return 04h - - return transition -
method
direction condition

Command argument Set range Contents

1 Detection method 0 to 3 Sets method for detection of origin location.
0: Unspecified (Err93.1 “Block data setting error protection” will occur).
1: Leading edge reference of vicinity of origin sensor (HOME) + z phase.
2: Leading edge reference of vicinity of origin sensor (HOME)
3: For manufacturer use

2 - - Please set to 0 (zero).

3 - - Please set to 0 (zero).
4 Origin return 0 to 1 Sets operation direction for origin detection.
direction 0: Positive direction, 1: Negative direction
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0, 1: Transitions to next block after completion of origin return.
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 - - Please set to 0 (zero).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 49 -

Example 1) Detection method 1: Leading edge reference of origin sensor (HOME) + z phase.

Example: Origin return direction

(positive direction) Start area Origin return direction (positive direction)

Negative direction Vicinity of origin input Positive direction limit

limit sensor ON ON sensor ON

z phase

H-SPD
L-SPD

L-SPD

H-SPD
H-SPD

L-SPD

H-SPD

L-SPD

H-SPD

Example 2) Detection method 2: Leading edge reference of vicinity of origin input (HOME)

Example: Origin return direction

(positive direction) Start area Origin return direction (positive direction)

Negative direction Vicinity of origin input Positive direction limit

limit sensor ON ON sensor ON

H-SPD
L-SPD

L-SPD

H-SPD

H-SPD
L-SPD

H-SPD

L-SPD

H-SPD

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 50 -

4-6 Decelerate stop

Command Code : 5h
Used in case of conducting forced stop of positioning action. *2

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument Argument Argument Argument
Argument 7
code 1 2 3 4 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Block (Reserved)
Stop
Decelerate stop 05h - - - transition -
method
condition

Velocity
Block operation Block operation
[r/min]
acceleration deceleration
setting [y] setting [z]

Block
operation
velocity [x]

3000

Time

Start Positioning Decelerate stop

(Stop method = 0)

Command argument Set range Contents

1 Stop method 0 to 1 Sets method of decelerating and stop.
0: Stops at the set deceleration established at the time of start up of the current action
1: Immediate stop
2 - - Please set to 0 (zero).
3 - - Please set to 0 (zero).
4 - - Please set to 0 (zero).
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0, 1: Transitions to next block after deceleration and stop. *1)
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 - - Please set to 0 (zero).

*1) “After deceleration and stop” shall mean the point when internal positioning command generation
processing has ended. It is not judged by the actual stopping of the motor. Furthermore, please note that
movement command will be issued even if the internal positioning command generation processing has
ended, in case position command filter (FIR, smoothing) is being used.
*2) Regarding software version (CPU1/CPU2) Ver1.05 or earlier, when this command is executed when
positioning action is not being executed, it may cause abnormal positioning thereafter (block operation state
output (BUSY) remains unchanged at 1). In such case, turn servo OFF to return to normal condition.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 51 -

4-7 Renew velocity

Command Code : 6h
To be used to renew the velocity of the current action.
Action prior to execution of this command will be continued during renewal of velocity and after renewal.
This is only valid for relative positioning action or absolute positioning action, and the velocity during origin return
action cannot be renewed during the action. Furthermore, velocity cannot be renewed, once the action has entered the
deceleration stop action.

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument Argument Argument Argument
Argument 7
code 1 2 3 4 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Operation Block (Reserved)
Velocity
Renew velocity 06h - - direction transition -
number
*2) condition

Example: Velocity change during absolute positioning (1st velocity ⇒ 2nd velocity)

Velocity Block operation Block operation

[r/min] 2nd acceleration 2nd deceleration
setting setting

Block
operation

3000

Block
operation
2nd velocity
Time

Absolute positioning Renew velocity Stop position = Target absolute position

Renew velocity only and stop at the initial
targeted position.

Command argument Set range Contents

1 Velocity number 0 to 15 Selects velocity after renewal.
Set selection number x for block operation velocity [x].
2 - - Please set to 0 (zero).
3 - - Please set to 0 (zero).
4 Operation
0 to 1 0: Positive direction, 1: Negative direction
direction *2)
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0: Transitions to next block after start.
1: Transitions to the next block after completing the action (that was in action
prior to renewal of velocity). *1)
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 - - Please set to 0 (zero).

Parameter Set range Unit Contents

Block operation velocity 0 to maximum [r/min] Sets velocity
[x] motor velocity

*1) “After completion of action” shall mean the point when internal positioning command generation processing has ended. It is not judged
by the actual stopping of the motor. Furthermore, please note that movement command will be issued even if the internal positioning
command generation processing has ended, in case position command filter (FIR, smoothing) is being used.
*2) Effective only under infinite length operation.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 52 -

4-8 Start decrement counter

Command Code : 7h
Used to start the decrement counter.
The value of the decrement counter is referenced by the conditional branch commands (Ah, Bh, and Ch).

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument Argument Argument Argument
Argument 7
code 1 2 3 4 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Block (Reserved) Counter set
Decrement
07h - - - - transition value
counter start
condition [1ms]

Decrement
counter value [1ms]
1ms

Counter
set value Δ1

Time

Decrement
counter start

Command argument Set range Contents

1 - - Please set to 0 (zero).
2 - - Please set to 0 (zero).
3 - - Please set to 0 (zero).
4 - - Please set to 0 (zero).
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0: Transitions to next block after start.
1: Starts counter and transitions to next block after counter stops (reaches 0).
Can be used as a wait timer until the start of the next block.
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 Counter set value 0 to 1000000 Sets the initial value of the decrement counter in 1[ms] units.
Counter will decrement from the initial value by 1 for each 1 ms cycle and will stop when
it reaches 0.
The value of the counter after start is used in the conditional branch command.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 53 -

4-9 Output signal operation

Command Code : 8h
To be used to operate the output signal.
Block operation output (B-CTRLn) must be assigned to the generic output terminal (SOn) in advance.

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument Argument Argument Argument
Argument 7
code 1 2 3 4 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Block (Reserved)
Output signal B-CTRL1 B-CTRL3 B-CTRL5
08h - transition -
operation B-CTRL2 B-CTRL4 B-CTRL6
condition

LSB =0: OFF (Output photo-coupler: OFF)

=1: ON (Output photo-coupler: ON)

MSB =0: No operation (retain current value)

=1: Operated

Command argument Set range Contents

1 B-CTRL1/B-CTRL2 0 to 15 The following operation is enabled when the generic output terminal SOn is set to the
2 B-CTRL3/B-CTRL4 0 to 15 block operation output B-DTRLn:
The following operations shall be set by the upper 2 bits for B-CTRL/3/5 and by the
3 B-CTRL5/B-CTRL6 0 to 15 lower 2 bits for B-CTRL 2/4/6:
0: No operation (retain current value)
1. For manufacturer use (Err93.1 “Block data setting abnormal protection” will occur.)
2: OFF (Photo-coupler output: OFF)
3: ON (Photo-coupler output: ON)
4 - - Please set to 0 (zero).
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0,1: Transitions to next block after start.
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 - - Please set to 0 (zero).
7 - - Please set to 0 (zero).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 54 -

4-10 Jump
Command Code : 9h
Used when transitioning (jumping) to the designated block number.

Blockdata [n] (64bit)

Command Data
Command name Command
Argument 1 Argument 2 Argument 3 Argument 4 Argument 5 Argument 6 Argument 7
code
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Block (Reserved)
Jump 09h - Block No. (destination) transition -
condition

Command argument Set range Contents

1 - - Please set to 0 (zero).
2 Block number 0 to 255 Set destination block number
3
4
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0,1: Transitions to designated block after start.
[MSB] 0,1: Continues block operation.
6 - - Please set to 0 (zero).
7 - - Please set to 0 (zero).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 55 -

4-11 Conditional branch

Command Code : Ah, Bh, Ch
Used when transitioning to the designated block number (destination when YES), when the designated conditions are
satisfied.

Blockdata [n] (64bit)

Command Data
Command name Command Argument Argument Argument
Argument 2 Argument 3 Argument 4 Argument 7
code 1 5 6
8bit 4bit 4bit 4bit 2bit 2bit 8bit 32bit
Block (Reserved)
Conditional For Compared value
0Ah Block No. (destination, if Yes) transition
branch (=) comparison (threshold)
condition
Block (Reserved)
Conditional For Compared value
0Bh Block No. (destination, if Yes) transition
branch (>) comparison (threshold)
condition
Block (Reserved)
Conditional For Compared value
0Ch Block No. (destination, if Yes) transition
branch (<) comparison (threshold)
condition

Command argument Set range Contents

1 For comparison 0 to 15 Value For comparison Unit Remarks
0 Command Command Command position after filter
position unit
1 Current position Command Current position of motor
unit
2 Position deviation Command Position deviation
unit ( = Command position - current position)
3 Command r/min Command motor velocity (before filter)
velocity
4 Motor velocity r/min Current motor velocity
5 Command torque 0.1% Command motor torque
6 Decrement - Decrement counter value
counter
7 Input signal - Can be used under conditional branch (=). *1)
8 Output signal - Can be used under conditional branch (=). *2)
9 to 15 (Reserved) - Please do not use
2 Block number 0 to 255 Specify the destination block number for the case that command conditions have been
3 satisfied (when YES).
4
5 Block transition 0 to 3 Sets block transition conditions after execution of this command.
condition [LSB] 0: If YES, transitions to designated block after start, and if NO, then to the next
block.
1: Will execute the block until it becomes YES, and will transition to the
designated block at YES.
[MSB] 0: Ends block operation for this block.
1: Continues block operation.
6 Compared value 80000000h Sets compared value (threshold).
(threshold) to 7FFFFFFFh Contents and units of compared values shall differ with the comparison subjects.

(Note) In case of conditional branch (=), there is a possibility of judgment error from sampling timing and
electronic gear input errors. In such case, please use conditional branches (>) or (<).

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 56 -

*1) Comparison subject: Input signal (7h)

Can be used under conditional branch (=). Err 93.1 (Block data set abnormal protection) will occur when
conditional branches (>) and (<) are set for comparison.
Transition to the designated block number (destination when YES) will be executed, when all conditions
for each of the signals are satisfied.

Compared value (4 byte) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
Function Byte
Signal LL SI8 SI7 SI6 SI5 SI4 SI3 SI2 SI1
condition LH - - - - - - SI10 SI9
With or HL SI8 SI7 SI6 SI5 SI4 SI3 SI2 SI1
without HH - - - - - - SI10 SI9
comparison
Always set 0 to the “for manufacturer use” bit (-).

The 4 byte compared value data is separated into 2 byte units.

▪ Upper 2 bytes (HH, HL): Sets whether to compare or not, for each bit.
0: Without comparison
1: Compare
▪ Lower 2 bytes: (LH, LL): Sets the value to be compared (signal state of physical level) for each
bit.
0: Input photo-coupler OFF (physical level)
1: Input photo-coupler ON (physical level)

*2) Comparison subject: Output signal (8h)

Can be used under conditional branch (=). Err 93.1 (Block data set abnormal protection) will occur when
conditional branches (>) and (<) are set for comparison.
Transitioning to the designated block number (destination when YES) will be executed, when all
conditions for each of the signals are satisfied.

Compared value (4 byte) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
Function Byte
Signal LL - - TLC ZSP BRK-OFF INP ALM S-RDY
condition LH - INP2 - WARN2 WARN1 - - -
With or HL - - TLC ZSP BRK-OFF INP ALM S-RDY
without HH - INP2 - WARN2 WARN1 - - -
comparison
Always set 0 to the “for manufacturer use” bit (-).

The 4 byte compared value data is separated into 2 byte units.

▪ Upper 2 bytes (HH, HL): Sets whether to compare or not, for each bit.
0: Without comparison
1: Compare
▪ Lower 2 bytes: (LH, LL): Sets the value to be compared (signal state of logic level) for each bit.
0: OFF (Logic level)
1: ON (Logic level)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 57 -

4-12 Block transition, start, and finish

4-12-1 Block transition conditions
The number of blocks that can be set is limited to a maximum of 256 and efficient block setting (block
programming) is necessary to conduct complex actions. Efficiency of block programming can be achieved by
effectively using block transition conditions.
Block transition conditions are set by argument 5 (Block transition condition) for each block, and the functions of
the upper bit (MSB) and the lower bit (LSB) are grouped as follows:

LSB : Sets block transition conditions in case of block continuation (MSB = 1) *1)
0 : Transitions to designated block after start of processing of subject block. *2)
1 : Transitions to designated block after completion of processing of subject block. *2)

MSB : Sets whether to end or continue with the block operation in this block.
0 : Ends block operation on completion of the block operation currently being
processed.
1 : Continues with block operation even after completion of the block operation
l b i d

*1) In case block end (MSB = 0) is set, the lower bit (LSB) setting will become invalid and block operation
will end upon completion of the processing of the subject block.
*2) The functions of lower bits (LSB) will vary with each command. The above indicates the basic commands,
however, for example, with jump command (9h), regardless of the set value, it will transition to the
designated block after start. Please refer to the explanations for each command for details.

4-12-2 Start and finish of block operation

To start block operation, designate the block No. to be started and turn strobe input (STB) ON. Block operation
state output (BUSY) will turn to 1 with the starting of block operation.
• Block No. designation: Register 4414h or I/F connector input (B-SEL 1 to 128)
• Strobe input (STB): Coil 0120h or I/F connector (STB)

To finish block operation, pre-set the block transition condition to MSB = 0 by the block No. command of the
block to be finished. Block operation state output (BUSY) will turn to 0 with the finish of block operation.
However, in case action type command (relative positioning, absolute positioning, origin return) is in the process
of being executed, before the subject block is reached, then block operation will not be completed until the action
has been completed (*1) and block operation condition output (BUSY) will continue to be 1.

*1) “Completion of action” shall mean the point when internal positioning command generation processing
has ended. It is not judged by the actual stopping of the motor. Furthermore, please note that movement
command will be issued even if the internal positioning command generation processing has ended, in
case position command filter (FIR, smoothing) is being used.

In addition, the following block operation will be forced terminated, as exceptional processing.

▪ When immediate stop or decelerated stop has been input (external input, Modbus
communications).
▪ Upon servo-OFF condition (including servo OFF caused by triggering of alarm or drive
prohibited input).
▪ Absolute potiosion has reached to the software limit.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 58 -

5. Block operation example

Block parameter Blockdata [n] (64bit)

Block set value Command Data
number Upper: Command Command code Argument 1 Argument 2 Argument 3 Argument 4 Argument 5 Argument 7
Lower: Data 8bit 4bit 4bit 4bit 2bit 2bit 32bit
B-CTRL1 OFF B-CTRL3 maintain B-CTRL5 maintain Block continue
08800200h Output signal operation - -
0 B-CTRL2 maintain B-CTRL4 maintain B-CTRL6 maintain Transition after start
00000000h
08h 8 0 0 0 2 0
Block continue
04200300h Origin return HOME leading edge - - Positive direction Transition after -
1 completion
00000000h
04h 2 0 0 0 3 0
B-CTRL1 ON B-CTRL3 maintain B-CTRL5 maintain
08E00000h Output signal operation - Block complete -
2 B-CTRL2 OFF B-CTRL4 maintain B-CTRL6 maintain
00000000h
08h Eh 0 0 0 0 0
02123200h Block continue Target absolute
Absolute positioning Velocity Acceleration Deceleration -
3 000186A0h Transition after start position
(100000) 02h 1 2 3 0 2 100000
Block continue
0B001700h Conditional branch Destination when YES
Command position Wait transition till Compared value
4 00007530h (>) (lock number 5)
YES
(30000)
0Bh 0 5 3 30000
Block continue
06200300h Renew velocity Velocity - - - Transition after -
5
00000000h completion
06h 2 0 0 0 3 0
B-CTRL1 maintain B-CTRL3 maintain B-CTRL5 maintain
08300000h Output signal operation - Block complete -
6 B-CTRL2 ON B-CTRL4 maintain B-CTRL6 maintain
00000000h
08h 3 0 0 0 0 0
00000000h - - - - - - -
7 to 255
00000000h 0h 0 0 0 0 0 0

Pr60.18
Velocity [r/min] Block Pr60.35
HOME operation Block operation
Pr60.01 Acceleration Deceleration setting [3]
Block operation
velocity [1]

3000
Pr60.02 Pr60.52
Block operation Origin return velocity
velocity [2] Pr60.53
(high speed)
Pr60.54 Origin return velocity
Origin return (low speed) Time
acceleration

Origin return start Returned to origin Absolute positioning Renew velocity if Stop position = Target
completed start command position > 30000 absolute position
(Modbus communication data)
[pulse] =100000 [pulse]
MIN 10ms *1)
Register 4414h
0 3
Block number
Coil 0120h ON OFF ON OFF
Strobe input operation
Block processing cycle +
Register 4416h α
Currently effective 1ms+α
block number
0 1 2 3 4 5 6

B-BUSY ON OF ON
Output
Signal B-CTRL1 OFF ON

B-CTRL2 OFF ON

*1) Maintain interval of 10 ms or more from B-SELn input to STB input.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 59 -

6. Applied functions

6-1 Infinite rotation absolute function

*This shall not apply to MINAS-A6L Series ([A6SL]/[A6SM]).

This is a function to allow the setting of the upper limit value of multi-rotation data of the absolute encoder
to any value.
This function enables the turntable angle of rotation (position) to be obtained in case the usage of a turntable,
etc. is rotated continuously in one direction, during use as a turntable, etc.
In addition, being an absolute encoder, there is no need to reset the origin after reclosing of the power
supply.

Turntable 1 rotation

Reduction rate
(Mechanical gear ratio)
1/m

m revolutions
1 rotation of turntable from m
revolutions of motor A6 motor

(1) Applicable scope

This function cannot be applied unless the following conditions are satisfied:
Condition where infinite length absolute function is activated
Control mode - Position control mode
Other - The amount of motor revolutions per 1 turntable rotation is an integer of 512 or
smaller.
- Command position per 1 turntable rotation
= Encoder resolution (223) / Electronic gear ratio / Reduction ratio (1/m), is an integer
of 223-1 or smaller.
- Elements other than the control parameter to be appropriately set and shall not
interfere with the normal revolutions of the motor.

(2) Related parameters

Classif
No. Parameter name Set range Unit Functions
ication
Sets the method of use of the absolute encoder.
0: Use under absolute system (Absolute mode)
1: Use under incremental system (incremental mode)
2: Ignore multi-rotation counter overflow even though used under
Absolute encoder the absolute system (Absolute mode).
0 15 0 to 4 -
set 3: For manufacturer use (Not to be set)
4: Upper limit of multi-rotation counter can be set at any value,
even though used under the absolute system (Absolute mode).
Ignore multi-rotation counter overflow. (infinite revolution
absolute mode)
Sets the upper limit value of absolute multi-rotation data.
When the multi-rotation data exceeds the set value, the multi-rotation
Absolute
data will change to 0.
6 88 multi-rotation 0 to 65534 -
Inversely, if it turns less than 0, it will change to this set value.
data upper limit
In case Pr0.15 is set to 0 or 2 (absolute mode), the upper limit value for
absolute multi-rotation data will be 65535, regardless of the set value.
Sets the amount of origin offset when return to origin has been
completed under block operations in increment mode, Sets the amount
Block operation -2147483648 Command
60 49 of offset between the encoder location and mechanical coordinate
origin offset to 2147483647 unit
system location under block operations in absolute mode. Setting bit 1
to 1 in Pr60.48 (Block operation method set,” will activate the setting.

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 60 -

(3) Notes
This function will become effective by setting Pr0.15 “Absolute encoder set” to 4, and reclosing the control
power supply.
- When the encoder multi-rotation data upper limit value and the amplifier parameter multi-rotation data
upper limit value does not match when the control power supply is reclosed, Err92.3 “Multi-rotation
data upper limit inconsistency error protection” will be triggered but this is not an error. Reclosing the
amplifier control power supply will eliminate any further occurrences.
- Set Pr6.88 “Absolute multi-rotation data upper limit value” to (m-1). m is the denominator of the
reduction ratio.
- The motor position will wrap around also at the position where the multi-rotation data will wrap
around.
- Command position should be provided to match this motor position.
- Please refer to item 2-6 for details of wrap around process.
- Set Pr6.88 “Absolute multi-rotation data upper limit value” so that the motor position and command
position will not exceed (231-1).
- The motor position of this amplifier is set, taking Pr0.00 “Rotational direction set,” Pr6.88 “Block
operation origin offset,” etc., into consideration.
- Please refer to Item 2-7 for details.
- Please refer to Item 4-7-1-1 of Technical Reference (Functional specification) for absolute system
configuration.
- Please set Pr60.49 “Block operation origin offset” within the range of 0 to ((Set value for Pr6.88 + 1) ×
encoder resolution / electronic gear ratio) -1, If setting is made outside this range Err93.8 “Parameter
set error protection” will be triggered.

(4) Operation example

Procedure when the electronic gear ratio is 223/4000, with a reduction ratio of 40 motor revolutions to 1
turntable rotation (m = 40) shall be as follows:
[1] Set Pr0.15 = 4 and Pr6.88 = 39, and write into EEPROM
[2] Reclose amplifier control power supply
[3] The multi-rotation data upper limit on the encoder side will be automatically renewed by switching on
the amplifier
[4] Err92.3 “Multi-rotation data upper limit inconsistency error protection” generated.
[5] Reclose amplifier control power supply
[6] Multi-rotation data upper limit is now effective and the motor position is generated as shown in the
figure below
[7] The motor position will wrap around at 223 × 40 -1. The command position shall match this and will
wrap around to operate.

* The multi-rotation data upper limit is maintained by a battery power source connected to the encoder.
When the amplifier control power supply is switched-on the next occasion, the procedure will start
from [6] above.

2
Amount of turntable
rotation 1
0 Position
Pr6.88

Absolute encoder 40 - 1
multi-revolution
data Position
0
31
<2
23
(2 ×40)/(223/40000)-1
Motor position =1599999
(command position) Position
0

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 61 -

(5) Absolute origin position offset

When using a 23-bit absolute encoder, the absolute origin position offset shall be as follows:

i) When CCW = positive direction, electronic gear ratio (Pr0.09 / Pr 0.10) = 1/1, Pr 6.88 “Absolute
multi-rotation data upper limit value” = 2, and Pr60.49 “Block operation origin offset” = 10000
223-1
Absolute encoder data

0
Absolute encoder data 2 2
Multi-revolution data 1 1
0 0

(223*3-1)

Motor position
(Command position)
10000 (Pr60.49)
0

ii)When CW = positive direction, electronic gear ratio (Pr0.09 / Pr 0.10) = 1/1, Pr 6.88 “Absolute multi-rotation
data upper limit value” = 2, and Pr60.49 “Block operation origin offset” = 10000
223-1
Absolute encoder data

0
Absolute encoder data 2 2
Multi-revolution data 1 1
0 0

(223*3-1)

Motor position
(Command position)
10000 (Pr60.49)
0

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 62 -

7. Protection functions to detect when Modbus communication/block operation function is effective

7-1 List of protection functions to detect when Modbus communication/block operation function is effective

(Note) Please refer to Technical reference (Functional Specifications) for protection functions other than those
indicated below.

Alarm number Attribute

Alarm name History Clear Immediate
Main Sub record enabled stop
*1)
27 1 Absolute clear abnormal protection ○ × ×
29 1 Counter overflow protection 1 ○ × ×
29 2 Counter overflow abnormal protection 2 ○ × ×
80 0 Modbus communication timeout protection ○ × ×
92 0 Encoder data recovery abnormal protection ○ × ×
92 1 External scale data recovery error protection ○ × ×
Multi-rotation data upper limit inconsistency
92 3
error protection ○ × ×
93 0 Parameter setup error 1 ○ × ×
93 1 Block data setting error protection ○ ○ ×
93 8 Parameter set error protection 6 ○ × ×
94 0 Block operation abnormal protection ○ ○ ×
94 2 Origin return abnormal protection ○ ○ ×
97 0 Control mode setting error protection × × ×

*1) Immediate stop indicates alarms that will trigger immediate stop, when Pr.5.10 (Sequence upon alarm) is set
between 4 and 7. Please refer to Technical Reference (Functional specification) for details.

7-2 Details of protection functions to detect when Modbus communication/block operation function is effective

Alarm number
Alarm name Cause Treatment
Main Sub

Absolute encode multi-rotation clear has been executed ▪ Confirm whether absolute encode multi-rotation clear has
by USB communications. been executed by USB communications.
Absolute clear
(Note) This is a safety measure and is not an abnormality.
27 1 abnormal
protection Alarm will not be triggered when multi-rotation clear is
conducted by Modbus communications, however, please
re-set the control power supply, even in this case.
The value of absolute encoder (absolute external ▪ Confirm the operational range of absolute encoder
scale) position [in pulse units] / electronic gear (absolute external scale) position and conduct a
Counter
ratio has exceeded ±231 (2147483648), in the review of the electronic gear ratio.
1 overflow error
position information initialization process after
protection 1
reclosing of control power supply in absolute
mode when block operation is valid,
The value of positioning deviation has exceeded ±230 ▪ Confirm that motor rotates in accordance with the
29 (1073741824) in command units. positioning command.
▪ Confirm that output torque has not saturated by the torque
Counter overflow monitor.
2 abnormal ▪ Adjust gain.
protection 2 ▪ Set Pr.0.13 (“1st torque limit setting” and Pr5.22 “2nd
torque limit setting” to maximum
▪ Connect encoder connection wiring as per the wiring
diagram.
Modbus
・ Set Pr5.40 ”Modbus communication timeout period”
Modbus communication against own axis has not been
communications received for more than the set time, under a state where
80 0 to 0 to be disabled or to appropriate time.
timeout rights have been acquired under register 4300h “Modbus
communication rights setting.” ・ Check the connection of Modbus communication.
protection

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 63 -

Alarm number
Alarm name Cause Treatment
Main Sub

Initialization process of internal position information has ▪ Secure encoder power supply voltage at DC5V±5% (4.75
not conducted normally under absolute and semi-closed to 5.25V). Care must be taken when the encoder lines are
Encoder data control mode. lengthy.
0 recovery abnormal ▪ If motor wires and encoder wires are bundled together,
protection
separate them.
▪ Connect shield to FG

Initialization of internal position location has been ▪ Secure power supply voltage of 5 VDC±5%(4.75 to
conducted abnormally under full closed control and 5.25 V) for the external scale. Special care should be
92 under absolute mode, with block operations valid taken in case the external scale connecting cable is
External scale
long.
1 data recovery
error protection ▪ In case the motor line and the external scale connecting
cable is bundled together, separate them.
▪ Connect shield to FG. Refer to connection diagram for
external scale.
Multi-rotation The encoder multi-rotation upper limit value and the ▪ Confirm set values of the parameters
data upper limit amplifier parameter multi-rotation data upper limit • In case it occurs immediately after switching the
3 control power supply on, reclose the control power
inconsistency value does not match, under. infinite revolution supply. (This is not abnormal.)
error protection absolute mode.
・ Check the setting value of the parameter.
[1] Electronic gear ratio exceeds the allowable range. [1] When a block operation was enabled (Pr 6.28 is
non 0), Electronic gear ratio must be in the range
Parameter setup [2] When block operation is valid by start by Modbus
0 1/1000 to 8000.
error 1 communications (Pr6.28 = 1) and Modbus
connection was disabled (Pr 5.37 is 0). [2] When a block operation was enabled (Pr 6.28 is
non 0), Modbus connection was disabled (Pr 5.37 is
0).
[1] Velocity, acceleration and deceleration have been set [1] Set value other than 0 to velocity, acceleration and
to 0 to start block operation. deceleration.
[2] Conditional branch command does not support the [2] Confirm there are no problems with the conditional
93 Block data setting subject of comparison. branch command or comparison subjects.
1 abnormal [3] Specified block data command was undefined. [3] Confirm there are no problems with the block data.
protection Confirm there are no problems with the block number
[4] Other, abnormal block data settings exists. designations.
[4] Confirm there are no problems with the block data
settings.
The absolute origin position offset has been set outside ▪ Check set values of parameters
the range under absolute mode origin offset valid
Parameter set error
8 setting (Pr60.48 bit 1 = 1) under infinite revolution
protection 6 absolute mode, when block operation is valid (Pr6.28
is other than 0).
[1] A new action command was executed while an [1] Confirm there are no problems with the block
action command (during execution of position operation sequence.
Block operation command generation process) was being executed.
[2] Start conducted by specifying new block number [2] Confirm there are no problems with the upper side
0 abnormal
while block operation was being conducted. sequence.
protection [3] Block operation started even though servo was OFF,
[3] Confirm there are no problems with the upper side
etc.
sequence.

94 [1] A block operation of origin return command was [1] Confirm there are no problems with the block data
executed while in absolute mode. settings or the absolute mode settings.
[2] Drive prohibited input for origin return direction has [2] Confirm there are no problems in the arrangement of
Origin return been turned ON during the origin return action, and the the drive prohibited input and the origin (sensor input,
abnormal drive prohibited input for the direction opposite to the Z phase).
2
origin return direction has been turned ON while it is in
protection
reverse action.
[3] Relative positioning or absolute positioning has been [3] Confirm there are no problems with the setting of
executed under origin return uncompleted state. block data and others.

Control mode Block operation is set to enabled, when other than

Check the setting of Pr 0.01”control mode setting” and
97 0 setting error Position control (Pr0.01 = 0) or full-close control (Pr0.01
Pr 6.28 “Special function selection”
protection = 6)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 64 -

8. List of parameters
Classification 0: Special settings
Related
Set
Class No Parameter title Unit Functions, contents Attribute control Relations
range
modes
Reclose
Absolute encoder
0 15 - 0 to 4 Select method of use of absolute encoder power All 6-1
setting
supply

Classification 5: Extended settings

Related
Class No Parameter title Unit Set range Functions, contents Attribute control Relations
modes
Set baud rate for RS232 communications.
RS232 0: 2400, 1: 4800, 2: 9600 3: 19200,
Reclose
communications 4: 38400, 5: 57600, 6: 115200, 7: 230400 bps
5 29 - 0 to 7 power All 2-1-2
baud rate setting Note) In case it is not Modbus communications
supply
*1 (Pr.5.37 = 0), when value is set to 7, it will be set
internally to 9600 bps.
Set baud rate for RS485 communications.
RS485 0: 2400, 1: 4800, 2: 9600 3: 19200,
Reclose
communications 4: 38400, 5: 57600, 6: 115200, 7: 230400 bps
30 - 0 to 7 power All 2-1-2
baud rate setting Note) In case it is not Modbus communications
supply
*1 (Pr.5.37 = 0), when value is set to 7, it will be set
internally to 9600 bps.
Sets axis number for communications.
In case of RS232 or RS485, please use within the
range up to 31.
Reclose
In case of Modbus, use within the range of 1
31 Axis number - 0 to 127 power All -
to 127.
supply
(However, the maximum number of connection axis
shall be limited to 31.)
0: will invalidate Modbus communications.
Sets RS232/RS485 communications protocol.
Modbus 0: MINAS standard protocol Reclose
37 connection - 0 to 2 1:Modbus-RTU (RS232 communications, 1:1 only) power All -
setting 2:Modbus-RTU (RS485 communications, 1:N supply
compatible)
Sets parity (Even, odd, none) and stop bit length (1
bit, 2 bits) for Modbus communications.
0: Even/1bit
Modbus Reclose
1: Even/2bit
38 communication - 0 to 5 power All 2-1-3
2: Odd/1bit
setting supply
3: Odd/2bit
4: None/1bit
5: None/2bit
Set waiting time to be added from the receipt of
Modbus Modbus communications request until response
Always
39 response waiting ms 0 to 10000 data is transmitted. All 2-1-3
effective
Time Note) Even if value is set to 0, delay will occur for
generation of response data.
Sets time to detect Err 80.0 “Modbus
communications time out protection”, in case
Modbus communications specifying own axis or
Modbus
broadcast could not be received within the set Always
40 communications ms 0 to 10000 All 2-1-3
length of time from the last time received, when effective
Time out time
rights have been acquired under register 4300h
“Modbus communication rights setting” and Err
80.0 is not detected when set value is 0.
(Continued)

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 65 -

Related
Class No Parameter title Unit Set range Functions, contents Attribute control Relations
modes
Sets request processing and response action, in case
broadcast mode request has been received in
Modbus communications.
bit 0 response action
0: Invalid (No action) 1: Valid (Action) *1
bit 1: Request processing
0: Valid (Process) 1: Invalid (No processing)
bit 2: Strobe input operation automatic off
0: invalid, 1: valid *2
bit 3: Request operation specification switch *1
Modbus
-32768 to 0: use Pr5.40, 1: Use Pr5.39 Always 2-1-3
5 42 broadcast - All
32767 bit 4 - 15: Not used Please set to 0 (zero). effective 2-1-4
Setting
The lowermost bit is designated as bit 0.
*1 In case bit 3 = 0,
returns response after Pr5.31 × Pr5.40[ms].
In case bit 3 = 1,
returns response after Pr5.31 x Pr5.39 [ms].
Does not return response when bit 1 = 1.
*2 After start-up of block operation, strobe input
operation will be automatically turn OFF from
the amplifier side. No need to write input OFF.
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
58 - power All 2-1-4
register setting 1 32767 address 4418h “Mirror register 1.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
59 - power All 2-1-4
register setting 2 32767 address 4419h “Mirror register 2.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
60 - power All 2-1-4
register setting 3 32767 address 441Ah “Mirror register 3.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
61 - power All 2-1-4
register setting 4 32767 address 441Bh “Mirror register 4.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
62 - power All 2-1-4
register setting 5 32767 address 441Ch “Mirror register 5.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
63 - power All 2-1-4
register setting 6 32767 address 441Dh “Mirror register 6.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
64 - power All 2-1-4
register setting 7 32767 address 441Eh “Mirror register 7.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
65 - power All 2-1-4
register setting 8 32767 address 441F h “Mirror register 8.”
supply
Reclose
Modbus mirror -32768 to Sets register address linked to Modbus register
79 - power All 2-1-4
register setting 9 32767 address 4420h “Mirror register 9.”
supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
80 register setting - power All 2-1-4
32767 address 4421h “Mirror register 10.”
10 supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
81 register setting - power All 2-1-4
32767 address 4422h “Mirror register 11.”
11 supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
82 register setting - power All 2-1-4
32767 address 4423h “Mirror register 12.”
12 supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
83 register setting - power All 2-1-4
32767 address 4424h “Mirror register 13.”
13 supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
84 register setting - power All 2-1-4
32767 address 4425h “ Mirror register 14.”
14 supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
85 register setting - power All 2-1-4
32767 address 4426h “Mirror register 15.”
15 supply
Modbus mirror Reclose
-32768 to Sets register address linked to Modbus register
86 register setting - power All 2-1-4
16 32767 address 4427h “Mirror register 16.”
supply

R2.1 Motor Business Unit, Panasonic Corporation

 No.SX-DSV03042 - 66 -

Classification 6: Special setting

Related
Class No Parameter title Unit Set range Functions, contents Attribute control Relations
modes
Selects valid/invalid of block operation functions.
0:Block operations invalid Reclose
Special function Block
6 28 - 0 to 2 1: Block operation valid by start by Modbus power 2-3
select operation
communication supply
2: Block operation valid by start by input signal
Sets absolute multi-rotation data upper limit value.
When the multi-rotation data exceeds this set value,
Absolute Reclose
the multi-rotation data will turn to 0. Inversely, if it
6 88 multi-rotation data - 0 to 65534 power All 6-1
goes below 0, it will change to this set value.
upper limit value supply
Internal value will be set to 65535 in case Pr0.15 is set
to 0 or 2 (absolute mode)

Classification 56 to 60: Block data

Please refer to Item 3-2 for details.

Classification 60: Block operation setting

Related
Class No Parameter title Unit Set range Functions, contents Attribute control Relations
modes
Reclose Block
Block operation -32768 to Set origin offset valid or invalid under
60 48 - power operatio 3-1
method set 32767 absolute mode supply n
Sets the amount of origin offset at origin
return completion in block operation under
increment mode.
-2147483648 Sets the amount of offset between the Reclose
Block operation Command Block
49 to encoder position of block operation under power 3-1
Origin offset unit operation
2147483647 absolute mode and the mechanical supply
coordinate system location. Set bit 1 of
Pr60.48 (Block operation method setting)
to make it valid.
Block operation -2147483648 Reclose
Command Sets soft limit range in block operation Block
50 Positive direction to power 3-1
unit after return to origin completion. operation
software limit 2147483647 supply
Block operation
-2147483648 Reclose
Negative Command Sets soft limit range in block operation Block
51 to power 3-1
direction software unit after return to origin completion. operation
2147483647 supply
limit
Origin return
Reclose
velocity under Sets high-speed operation velocity for Block
52 r/min 0 to 20000 power 3-1
block operation. return to origin operation
supply
(high speed)
Origin return
Reclose
velocity under Sets low-speed operation velocity for Block
53 r/min 0 to 20000 power 3-1
block operation. return to origin operation
supply
(low speed)
Block operation ms/ Reclose
Sets acceleration and deceleration for Block
54 Origin return (3000r/ 0 to 10000 power 3-1
return to origin operation
acceleration supply
min)
Set to 1 when conducting relative
Set invalid block Reclose
positioning operations and absolute Block
55 operation origin - 0 to 1 power 3-1
positioning operations, without return to operation
return supply
origin operation under increment mode.

R2.1 Motor Business Unit, Panasonic Corporation