Scribd
Upload
997 views11 pages

Form Inspeksi Pompa

This document provides information about a centrifugal pump including its operating conditions, performance characteristics, vibration checks, and pump data. Key details include the pump's capacity, pressures, head, speed, materials of construction, power rating, efficiency, and vibration velocity measurements for both the drive end and non-drive end bearings. The pump performance curve number, total and maximum differential heads, NPSH requirements, and flow rates are also specified.

Uploaded by

Shada Mohammed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
997 views11 pages

Form Inspeksi Pompa

This document provides information about a centrifugal pump including its operating conditions, performance characteristics, vibration checks, and pump data. Key details include the pump's capacity, pressures, head, speed, materials of construction, power rating, efficiency, and vibration velocity measurements for both the drive end and non-drive end bearings. The pump performance curve number, total and maximum differential heads, NPSH requirements, and flow rates are also specified.

Uploaded by

Shada Mohammed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 11

CENTRIFUGAL PUMP DATA

Facility Adress
name

Installed Area
Location

Operating Conditions (at installation) Liquid Data


Capacity (GPM) Liquid Description
Suction Pressure (PSI) Temperature
Discharge Pressure (PSI) Specific Gravity
Head Pressure (TDH) Viscosity (cp)
Speed (RPM) pH
Ambient Temperature Solid Size & Content
Pump Mounted (Inside or Outside)

Pump Data Sealing Data


Manufacturer Packing or Mechanical Sea
Model Mechanical Seal Information
Serial Number - Single Seal or Double Seal
Pump Size - Component or Cartridge
- Discharge Diameter - Seal Manufacturer
- Inlet Diameter - Face Materials
- Case Size - O Ring Compound
Impeller Diameter - Flush Yes/No
Material of Construction Shaft Size
- Case Material
- Impeller Material

Motor Data Drive Data


Horsepower Coupling Drive or Belt Drive
3 Phase or 1 Phase Coupling Information
Speed (RPM) - Coupling Brand
Voltage - Coupling Model
Frame - Coupling Size
Enclosure - Insert Material
Service Factor Motor Shaft Size
Full Load Amps Pump Shaft Size
Amp Reading (Under Load)
Amp Reading (No Load)
Manufacturer

Coments :
Centrifugal Pump Data

Rev. No.:_________ Rev. Date:_____________________

Facility name / location:


Item name: Purchaser / location:
Item tag number: Job number:
Service: Purchaser order number:
Unit: Supplier / location:
P&ID number: Supplier order / serial numbers:

GENERAL

No. of pumps req.: Motor item number:


Pump size: Motor provided by:
Pump model: Motor mounted by:
Pump type: Variable speed operation: yes no
Power Rating (HP) Location : Indoor Outdoor

Operating Conditions

Rated Additional duty points (max., min., or VS)


Point #: 1 2 3 4 5
Flow: (gpm)
Head: (ft)
NPSHA: (ft)
Suct. pres.: (psig)
Speed: (rpm)

System design:
Suction pressure: min. / max : (psig)
Suction temperature: min. / max : (°F)
Stand-alone operation
Parallel operation with item no.:
Series operation with item no.:
Service :
Continuous intermittent: starts/day

System control method:


Speed Throttle System Resistance Only
Performance

Performance curve number: Speed : (rpm)


Total differential head @ rated impeller: (ft)
Maximum differential head @ rated impeller: (ft)
Point #: 1 2 3 4 5
NPSHR : (ft)
Minimum continuous stable flow: (gpm)
Allowable operating region: to (gpm)
Best efficiency point for rated impeller (gpm)
Suction specific speed:
Impeller diameter: Rated: Max: Min : (in.)
Pump rated power: (BHP) Efficiency: (%)
Maximum power with rated impeller: (BHP)
Case pressure rating:
Maximum allowable working pressure: (psig) @ (°F)
Hydrostatic test pressure: (psig)
Vibration Check

Bearing housing vibrations (velocity) measurement


Equipment variable check Drive End Non-Drive End
Horizontal Vertical Axial Horizontal Vertical Axial
Velocity (mm/s)
Motor
Displacement (µm)
Velocity (mm/s)
Pump
Displacement (µm)
D
11
C
7.1

4.5
B
3.5

2.8

2.3

1.4
A
0.71
mm/s rms inch/s rms
rigid flexible rigid flexible rigid flexible rigid flexible Foundation
pumps > 15 KW medium sized machine large machine
radial, axial, mixed flow 15 KW < P ≤ 300 KW 300 KW < P < 50 MW
Machine Type
motors motors
integrated driver eksternal driver
160 mm ≤ H < 315 mm 315 mm ≤ H

Group 4 Group 3 Group 2 Group 1 Group


Velo
city

0.43

0.28

0.18
10 -
0.14 1000 Hz
r > 600
0.11 rpm
2 - 1000
Hz r >
0.09 120 rpm

0.06

0.03
mm/s rms inch/s rms
Foundation

Machine Type

Group

You might also like