Course Title:ENGINEERING DRAWING-II

Credits (L:T:P) : 0:2:4 Total Contact Hours: 78 Course Code: 15CE22D

Type of Course:
Tutorialand Drafting Credit :03 Core/ Elective: Core

(***(Common to all Civil/Civil (Draughtsman/Environmental/Public Health Engineering/Water Technology and Health

Sciences Programme)***

Prerequisites: Student should know Engineering Drawing-I

Course Objectives
1. The course is aimed at developing Basic Drawing skills.
2. Develop Skills in Preparation of Engineering Drawings.
3. Develop Skills In Preparation of Engineering Drawings, their Reading and Interpretation

Course Outcomes
On successful completion of the course, the students should be able to:
Course Outcome
CO1 Draw Orthographic views of given Civil Engineering Objects.
CO2 Develop the ability to draw the isometric view from the orthographic views of a
given Building Components and vice versa.
CO3 Develop the perspective views for simple Civil Engineering components
CO4 Understand the concept of developing cross sections for Building components.
CO5 Develop Plan and Elevation for single and two room Buildings for sustainable
development

Mapping of COs with POs

Programme Outcome
PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12
Design and Development of

Individual and Team work

Investigation of problems

Project management and

Engineering Knowledge

Engineer and society

Modern Tool Usage

Life long learning

Problem Analysis

Mapping
Communication
Environment &
Sustainability

of COs
Solution

finance
Ethics

with Pos

CO1 S S   S S  S
 
Course Outcome

CO2 S S
  S S  S S 
CO3 S S
  S S  S
 
CO4 S S   S S  S
 
CO5 S S  S  S S  S
 S
Key: S-Strong Relationship M-Moderate Relationship

Directorate of Technical Education Karnataka State 1

Course Contents

UNITS COURSE CONTENTS HOURS

PROJECTION OF SOLIDS
Introduction-Positioning of solids –Solid lying with base on HP- Solids lying
with base or axis inclined to HP- Solids lying with one of the lateral faces on HP-
1 Solids lying with one of their lateral edges on HP-Cylinder lying with its axis or 15
base inclined to HP- Cone lying with its axis or base inclined to HP -Solid lying
with their axis inclined to both HP and VP.

CONVERSION OF ISOMETRIC VIEWS INTO ORTHOGRAPHIC

VIEWS
Introduction –
2 06
Guidelines for conversion of pictorial views into orthographic views-Illustrative
problems.

ISOMETRIC VIEWS
Principles of isometric Views
Isometric views of simple solids – cube – prisms, pyramids, cylinder and cone .
3 Conversion of orthographic views into isometric View 15
Drawing of Isometric views of combination of solids , Civil Engineering
components i.e. column footing, carpentry joints

PERSPECTIVE PROJECTIONS
4 Technical terms used in perspective projection- one point Perspective projection
12
and two point perspective projection for simple objects like Cube, Prism,
Pyramids, combination of solids and simple civil engineering objects,.
CROSS SECTION OF BUILDING COMPONENTS
Conventional Representation of Civil Engineering materials.
5 Cross section of Wall showing components of a Building from parapet to 09
foundation through door, window, wardrobe, wall, steps & columns.

BUILDING DRAWING
Draw Plan, Elevation and Section for Single ,Double Room Building and Three
6 Room Building form the given line Diagram and Building details. 21

Total
78 Hrs

Directorate of Technical Education Karnataka State 2

TEXT BOOK

1. K.R.Gopalakrishna “Fundamentals of Drawing” Subhas Publications, 2010.

2. K.R.Gopalakrishna “Engineering Drawing” (Vol. I & II), Subhas Publications, 2014.

REFERENCES

1. R.K. Dhawan, “A text book of Engineering Drawing”, S.ChandPublishers, Delhi, 2010.

2. G.S. Phull and H.S.Sandhu, “Engineering Graphics”, Wiley Publications, 2014.
3. K.Venugopal and V.Prabhu Raja, “Engineering Graphics”, New Age International Private
Limited,2008.
4. M.B.Shah and B.C.Rana, “Engineering Drawing”, Pearson Education, 2005.
5. DhananjayA.Jolhe, “Engineering Drawing with an Introduction to AutoCAD”, Tata McGraw
Hill Publishing Company Limited, 2008.
6. BasantAgarwal and Agarwal.C.M., “Engineering Drawing”, Tata McGraw Hill Publishing
Company Limited, New Delhi, 2008.
7. IS 962 (1989) Code of practice for Architectural and Building Drawings

Course Assessment and Evaluation Scheme:

Metho What To When/Where Max Evidence Course

d whom (Frequency Marks collected outcomes
in the course)
CIE IA Students Graded 25 Drawing 1,2,3,4,5
Direct Assessment

Exercises Sheets
(Average of
marks allotted
to each graded
exercise)
SE End End of the 100 Answer scripts 1,2,3,4,5
E Exa course at BTE
m
Student Students Middle of the Feedback 1, 2,3 ,Delivery
Indirect Assessment

Feedback course forms of course

on course
End of End of the Questionnaires 1,2,3,4,Effectiv
Course course eness of
Survey Delivery of
instructions &
Assessment
Methods

Questions for CIE and SEE will be designed to evaluate the various educational components
such as:
1. Remembering and Understanding : - 20% weightage
2. Applying the knowledge acquired from the course : - 65 % weightage
3. Analysis : - 10% weightage
4. Evaluation : - 2% weightage
5. Creating new knowledge : - 3% weightage

Directorate of Technical Education Karnataka State 3

 Weightage of Marks
Questions to be Questions to be
Unit set for set for
Hour
No Unit Name (10marks ) (15marks)
PART - A PART - B
I PROJECTION OF SOLIDS 15 02 (30 Marks)
CONVERSION OF PICTORIAL
II VIEWS INTO ORTHOGRAPHIC 06 01 (20 Marks)
VIEWS
III ISOMETRIC PROJECTIONS 15 02 (30 Marks)

IV PERSPECTIVE PROJECTIONS 12 01(15 Marks)

CROSS SECTION OF BUILDING
V 09 02 (20 Marks)
COMPONENTS
VI BUILDING DRAWING 21 01(35 Marks)

05 (75Marks)
03 (30Marks) Any 3
Total 78
Any 2
01 (35 marks)

GRADED EXERCISES

MINIMUM
UNIT TITLE OF THE
SHEETS NO OF
NO NAME OF THE UNIT DRAWING
EXERCISE

I PROJECTION OF SOLIDS 5 Projection of solids 20

CONVERSION OF ISOMETERIC 3
Isometric
II VIEWS INTO ORTHOGRAPHIC 15
projections
VIEWS
ISOMETRIC PROJECTIONS 5 Isometric
III 20
projections
IV PERSPECTIVE PROJECTIONS 4 Perspective
16
projections
CROSS SECTION OF BUILDING 3 Cross section of 15
V
building
COMPONENTS components
VI BUILDING DRAWING 6 Building drawing 10
TOTAL 26 96

Directorate of Technical Education Karnataka State 4

Model Question Paper
Code: 15CE22D
II semester Diploma Examination
ENGINEERING DRAWING-II

Time: 4 Hours][Max. Marks: 100

Note: Answer Any Three full questions from Part-A, Any 3full Questions from Part B&Part C is
compulsory.

Part –A(Any Two)

1. Draw the three principal views of the component as shown in the figure 1 10 marks

Fig-1

2. Draw the three principal views of the component as shown in the figure2

Fig.2

3.Show the conventional representation of Building materials in Section (IS: 962)10 marks
(a) Brick Masonary (b) Stone Masonary (c) Steel works (d)Wood

PART-B(Any Three)

4. An equilateral triangular prism 30 mm side of base and 50mm long rests with one of its shorter
edge on HP such that rectangular face containing the edge on which the prism rests is inclined at
300 to HP. The edge on which the prism rests is inclined at 600 to VP. Draw its projections.
15marks

Directorate of Technical Education Karnataka State 5

5. A cylinder of 40mm diameter and axis height 60mm is resting with its ends of the base diameter
on HP. The axis of the cylinder is inclined at 30° to the HP and appears to be inclined at 45° to
VP. Draw the projections of the solid in its final position.
15marks

6. Draw the isometric view of the following objects whose orthographic views are given Fig 3
15 marks

Fig-3

7. Draw the isometric view of the following objects whose orthographic views are given Fig 4

15marks

Fig-4

8. A Square based prism of 30mm side of base and height 50mm rests with its base and height 50mm
rests with its base on ground such that one of the rectangular faces is touching the picture plane.
The station point lies on the center line of the object, 60mm aboveground and 50mm in front of
the picture plane. Draw the perspective view of the square prism.
15 marks

PART- C(Compulsory)
9.The Line Diagram of a Two room building is shown in Fig 5.The Details and specification are as
follows. 35 Marks
Directorate of Technical Education Karnataka State 6
 (a) Level of Plinth above ground - 0.5m
(b) Height of ceiling from the floor- 3m
(c) Burnt Brick Masonry wall Thickness of wall 0.3m
(d) Doors 1.0mX 2.1m
(e) Windows 1.2mX1.2m
(f) RCC Roof 0.15m thick
(g) Parapet wall of Burnt Brick Masonry 1m height of 0.2m thick.
(h) Provide suitable Foundation of Size Stone Masonry

Draw to a scale of 1:50

(i) Plan of the Building and 15Marks
(ii) Front Elevation of the Building. 10Marks
(iii) Section along xx 10 Marks

MODEL QUESTION BANK

Course: ENGINEERING DRAWING-ICode: 15CE22D

UNIT-I (15 Marks)

1. A hexagonal pyramid, base 30mmside and axis 60mm long has one of its triangular face
containing the slant edge on which it rests are equally inclined to HP. The axis appears to be
inclined at 450 to VP. Draw its projections when its base is nearer to the observer than its apex.

2. Draw the projection of a pentagonal prism of base side 25mm and axis length 45mm resting on
a corner such that the two base edges passing through it make equal inclination with HP and its
base inclined at 60° to HP and the axis appears to be inclined at 30° to VP in the top view.

Directorate of Technical Education Karnataka State 7

3. An equilateral triangular prism 30 mm side of base and 50mm long rests with one of its shorter
edge on HP such that rectangular face containing the edge on which the prism rests is inclined at
300 to HP. The edge on which the prism rests is inclined at 600 to VP. Draw its projections.

4. A cone of base diameter 50mm and altitude 70mm is lying with one of its generators on HP and
the axis appears to be inclined to VP at an angle of 400 in the top view. Draw its top and front
views.

5. A Hexagonal prism of 30 mm side of base and axis 60mm long is placed with one of its base
edges on HP such that the axis is inclined at 350 to HP and 450 to VP. Draw its projections.

6. A Pentagonal pyramid 25mm side of base and 50mm altitude rests with one of its corners on
HP such that the two base edges passing through the corner on which rests make equal
inclinations with HP. The axis is inclined at 500 to VP and 300 to HP. Draw the top and front
views of the pyramid.

7. A cone of base 60mm diameter and axis 80mm long rests on HP with its axis inclined 45 0 to HP
and 300 to VP. Draw the top and front views of the cone.

8. Draw the top and front views of a right cylinder of base 50mm diameter and 70mm long when it
lies on HP, such that its axis is inclined at 300 to HP and axis appears to be perpendicular to VP
in the top view.

9. An equilateral triangular prism of base side 25mm and 50mm long rests with one of the its
shorter edges on HP so that the rectangular face containing the edge on which the prism rests
inclined at 30° to the HP. The edge on which the prism rests is inclined at 60° to the VP. Draw
its projections.

10. A pentagonal prism of base edge 30mm and 60mm long has its base edge on HP. The axis of
the prism is inclined at 30° to the HP and appears to be inclined at 45° to the VP. Draw the top
view and the front views of the prism.

11. A hexagonal prism of 30mm base edge and axis 60mm long is placed with one of its base edges
on HP so that the axis is inclined at 30° to HP and the axis appears to be inclined at 45° to VP.
Draw the projections when the base of the prism is nearer to the observer.

12. A square prism of base edge 40mm and 60mm long rests with one of its corners of the base so
that the longer edge passing through this corner is inclined at 40° to the HP. Draw the
projections if the axis appears to be inclined at 45° to the VP in the top view.

13. A square pyramid of base edge 40mm and 60mm long has one of its shorter edges on HP. The
axis of the pyramid is inclined at 30° to the HP and appears to be inclined at 45° to the VP.
Draw the projections if the apex is near to the observer.

14. A cylinder of 40mm diameter and axis height 60mm is resting with its ends of the base diameter
on HP. The axis of the cylinder is inclined at 30° to the HP and appears to be inclined at 45° to
VP. Draw the projections.

15. A cone of base diameter 50mm and axis 80mm lies on HP with its axis inclined at 45° to HP and
appears to be inclined at 30° to the VP in the top view. Draw the top and front views of the
cone.

Directorate of Technical Education Karnataka State 8

16. A right cylinder is 50mm diameter of base and height 70mm. It rests such that the axis is
inclined at 30° and 45° to HP and VP respectively. Draw the top and front views.

17. A cone of base 80mm diameter and height 100mm is lying with one of its generators on HP and
its axis appears to be inclined at 40° to VP in the top view. Draw its front and top views.

18. Draw the projections of a pentagonal prism 20mm side of base and axis 40mm long resting on a
corner such that two base edges passing through it make equal inclinations with HP and its base
is inclined at 60° to HP, and the axis appears to be inclined at 30° to VP in the top view.

19. Draw the top and front views of a rectangular pyramid of sides of base 20x25mm and height
35mm when it lies with one of its triangular faces containing the longer edge of the base on HP.
This longer edge of the base containing the triangular face lying on HP is inclined at 60° to VP
in the top view with the apex of the pyramid nearer to VP.

20. A pentagonal pyramid 20mm side of base of 35mm altitude rests with one of its corners on HP
such that the two base edges passing through the corner on which it rests make equal
inclinations with HP. The axis is inclined at 45° to VP and 30° to HP. Draw the top and front
views of the pyramid.

21. A hexagonal pyramid, base 30mm side and axis 60mm long has one of its slant edges on HP
such that two of its triangular faces containing the slant edge on which it rests are equally
inclined to HP. The top view of the axis appears to be inclined at 45° to VP. Draw its
projections when its base is nearer to the observer than its apex.
22. A cone of base 60mm diameter and axis 80mm long rests on HP with its axis inclined 45° and
30° with HP and VP respectively. Draw the top and front views of the cone.

23. Draw the top and front views of a right cylinder of base 45mm diameter and 60mm long when it
lies on HP, such that its axis is inclined at 30° to HP and the axis appears to be perpendicular to
the VP in the top view.

UNIT-2(10 MARKS)
1. Draw the three principal views of the component as shown in the figure.

Fig-1

Directorate of Technical Education Karnataka State 9

 Fig-2

Fig-3

Fig-4

Directorate of Technical Education Karnataka State 10

 Fig-5

Fig-6

UNIT-3 (15 Marks)

1. Draw the isometric view of the following objects whose orthographic views are given below:

Directorate of Technical Education Karnataka State 11

 2. Draw the isometric view of the following objects whose orthographic views are given below:

3. Draw the isometric view of the following objects whose orthographic views are given below:

Directorate of Technical Education Karnataka State 12

 4. Draw the isometric view of the following objects whose orthographic views are given below:

Fig-1

Fig-2

Fig-3
Directorate of Technical Education Karnataka State 13
 Fig-4
5. A Circular column of side 40mm and height 50mm is placed centrally on a square footing of
side 100mm and thickness 25mm. Draw the Isometric projections of the combination

6. A Cube of side 50mm is resting coaxially over a circular slab of diameter 100mm and
thickness 30mm.Draw the isometric view of the combination of the solid.

7. A cone having diameter of the base 60mm and height 70 mm is resting co- axially on the
square slab of side 100mm and thickness 40mm. Draw the isometric view of the combination
of the solid.

8. A cylinder of 50mm diameter and 50mm high is placed centrally on the rectangular footing
of sides 75mm and 100mm and thickness 25mm. Draw the isometric projections of the
arrangement.

9. A frustum of a cone 30mm top diameter and 60mm bottom diameter and 70mm long is
placed vertically on a square block of 80mm side and 30mm thick such that both the solids
have common axis. Draw the isometric of the combination of the solids.

10. A cylindrical slab 100mm diameter and 40mm thick is supporting a cube of 50mm edge. On
the top of the cube rests a square pyramid of altitude 55mm and side of base 30mm such that
the base edges of the pyramid are parallel to the edges of the top face. The axes of the solids
are in the same straight line. Draw the isometric projection of the combination of the solids.

11. A square pyramid of base edge 50 mm and height 80 mm rests on the top of the cube of side
100 mm. Two sides of the base of the pyramid are parallel to the top edges of the cube. Draw
the isometric view of the solid.

12. Three cubes of sides 60mm,40mm and 20mm are placed centrally one above the other. Draw
the isometric projections of the combination.

UNIT-IV (15MARKS)
1. A Square based prism of 30mm side of base and height 50mm rests with its base and height
50mm rests with its base on ground such that one of the rectangular faces is touching the
picture plane. The station point lies on the center line of the object, 60mm aboveground and
50mm in front of the picture plane. Draw the perspective view of the square prism.

Directorate of Technical Education Karnataka State 14

 2. A Cube of side 50mm side rests with its base on ground such that one of the square face is 20
mm behind the picture plane. The station point lies on the centerline of the object, 80mm
above ground and 75mm in front of the picture plane.

3. A rectangular based pyramid of sides of base 30mm and 20mm, and height 35mm rests with
its base edges in parallel to the picture plane and 30mm behind it. The station point is 50mm
in front of the picture plane, 30mmto the left of the axis of the pyramid and 50mm above the
ground. Draw the perspective view of the pyramid.

4. A model of steps has three steps of 15mm tread and rise 10mm. The steps measure 60mm
widthwise. Draw the perspective view of the model when placed with its first step 25mm
behind the picture plane and longer edge being parallel to it. The station point is 95mm from
the picture plane, 60mm above ground and lies on the center line.

5. Draw one point parallel perspective view of the block shown below. The station point is
located at 80mm to the right of the centre of the block and 100mm from the picture plane.
The observers eyelevel is 60mm above the ground level.

Fig-1

6. Draw the perspective view of a cube 25mm edge, resting on ground on one of its faces. It has
one of its vertical edges in the picture plane and all its vertical faces are equally inclined to
the picture plane. The station point is 55 mm in front of the picture plane. The station point is
55mm in front of the picture plane, 40mm above the ground and is in a central plane 9mm to
the left of the centre of the cube.

7. A Square prism of 30mm side of base and height 40mm rests with its base on ground such
that one of the rectangular faces is inclined at 300 to the picture plane. The nearest vertical
edge touches the picture plane. The station point is 45mm infront of the picture plane, 65mm
above ground and lies opposite to the nearest vertical edge that touches the picture plane.
Draw the perspective view.

Directorate of Technical Education Karnataka State 15

 8. A cube of 45mm side of base rests on ground such that one of the square face is inclined at
250 to the picture plane. The nearest vertical edge touches the picture plane. The station point
is 65mm in front of the picture plane, 85mm above ground and lies opposite to the nearest
vertical edge that touches the picture plane. Draw the perspective view.

9. Draw one point perspective view of the block shown below. The station point is located at
80mm to the right of the centre of the block and 100mm from the picture plane. The
observers eye lebvel is 60mm above the ground level.

Fig-2

10. Draw the two point perspective view of the model shown in fig3 when its right touches
picture plane and its longer side makes an angle of 300 with it. The station point is 100 mm in
front of the picture plane and exactly opposite to the vertical edge touching the picture plane
and the point of the sight is 120mm above the ground.

Directorate of Technical Education Karnataka State 16

 UNIT-V (10 Marks)

1. Show the conventional representation of Building materials in Section (IS: 962)

2. Draw the cross section of wall from foundation to parapet for the given details.

UNIT-VI (35 Marks)

1. The Line Diagram of a Single room building is shown in Fig 1.The Details and specification
are as follows.
(a) Level of Plinth above ground - 0.5m
(b) Height of ceiling from the floor- 3m
(c) Burnt Brick Masonry wall Thickness of wall-0.3m
(d) Doors 1.0mX 2.1m
(e) Windows 1.2mX1.2m
(f) RCC Roof 0.15m thick
(g) Parapet wall of Burnt Brick Masonry 1m height of 0.2m thick.
(h) Provide suitable Foundation of Size Stone Masonary

All Dimensions in Metre

.
Draw to a scale of 1:50
(i) Plan of the Building and
(ii) Front Elevation of the Building.
(iii) Section along xx

2. The Line Diagram of a two room building is shown in Fig 2.The Details and specification are
as follows.

(a) Level of Plinth above ground - 0.5m

(b) Height of ceiling from the floor- 3m
(c) Burnt Brick Masonry wall Thickness of wall- 0.3m
(d) Doors 1.0mX 2.1m
(e) Windows 1.2mX1.2m
(f) RCC Roof 0.15m thick
(g) Parapet wall of Burnt Brick Masonry 1m height of 0.2m thick.
(h) Provide suitable Foundation of Size Stone Masonary

Directorate of Technical Education Karnataka State 17

 All Dimensions in Metre.

Draw to a scale of 1:50

(i) Plan of the Building and
(ii) Front Elevation of the Building.
(iii) Section along xx

Directorate of Technical Education Karnataka State 18