A

MANAGEMENT SERVICE

ISO 9001

A
 A

High efficiency (η 0.95÷0.97) thanks

to the high performance offered
by the patented hypoid bevel gear pair
at output

Low-noise gearing

High load capacity

 INDEX 2.13 SPEED REDUCER RATING CHARTS . 50

2.14 MOTOR AVAILABILITY . . . . . . . . . . . . . 64

1.0 GENERAL INFORMATION 2.15 MASS MOMENT OF INERTIA . . . . . . . . 67

2.16 DIMENSIONS . . . . . . . . . . . . . . . . . . . . 76

1.1 SYMBOLS AND UNITS . . . . . . . . . . . . . . 2 2.17 TORQUE ARM. . . . . . . . . . . . . . . . . . . 117

1.2 TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.3 POWER . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.0 ELECTRIC MOTORS

1.4 THERMAL CAPACITY. . . . . . . . . . . . . . . 3

1.5 EFFICIENCY . . . . . . . . . . . . . . . . . . . . . . 4 3.1 GENERAL INFORMATION . . . . . . . . . 120

1.6 MASS MOMENT OF INERTIA. . . . . . . . . 4 3.2 MOTOR ORDERING NUMBERS . . . . 121

1.7 SERVICE FACTOR . . . . . . . . . . . . . . . . . 4 3.3 MECHANICAL CHARACTERISTICS . . 122

1.8 SELECTION. . . . . . . . . . . . . . . . . . . . . . . 5 3.4 ELECTRICAL CHARACTERISTICS . . 124

1.9 VERIFICATIONS . . . . . . . . . . . . . . . . . . . 9 3.5 BRAKE MOTORS . . . . . . . . . . . . . . . . 127

1.10 INSTALLATION . . . . . . . . . . . . . . . . . . . . 9 3.6 DC BRAKE MOTORS TYPE BN_FD . 128

1.11 STORAGE . . . . . . . . . . . . . . . . . . . . . . . 10 3.7 AC BRAKE MOTORS TYPE BN_FA. . 132

1.12 MAINTENANCE. . . . . . . . . . . . . . . . . . . 10 3.8 BRAKE RELEASE SYSTEMS. . . . . . . 134

3.9 SPECIAL EXECUTIONS . . . . . . . . . . . 135

2.0 BEVEL-HELICAL GEARMOTORS
3.10 COMPACT MOTOR RATING CHARTS. . 139

3.11 IEC MOTOR RATING CHARTS . . . . . 142

2.1 ORDERING NUMBERS . . . . . . . . . . . . 12
3.12 DIMENSIONS . . . . . . . . . . . . . . . . . . . 145
2.2 DESIGN ADVANTAGES . . . . . . . . . . . . 14

2.3 VERSIONS . . . . . . . . . . . . . . . . . . . . . . 14

2.4 SPEED REDUCER OPTIONS. . . . . . . . 14

2.5 SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . 14

2.6 LUBRICATION. . . . . . . . . . . . . . . . . . . . 15

2.7 MOUNTING POSITION AND

TERMINAL BOX SPECIFICATION. . . . 16

2.8 OVERHUNG LOADS . . . . . . . . . . . . . . . 22

2.9 SHAFT ARRANGEMENT . . . . . . . . . . . 23

2.10 ANTI-RUN BACK DEVICE . . . . . . . . . . 23

Revisions
2.11 INSTALLATION INSTRUCTIONS . . . . . 24 Refer to page 150 for the catalogue revision index.
Visit www.bonfiglioli.com to search for catalogues with latest revision
2.12 GEARMOTOR RATING CHARTS. . . . . 25 index.

1
1.0 GENERAL INFORMATION

1.1 SYMBOLS AND UNITS

Symb. U.m. Description Symb. U.m. Description

Ac [lbs] Calculated thrust load Pt [hp] Thermal capacity

An [lbs] Rated thrust load Pr [hp] Power required

fm – Adjusting duty factor Rc [lbs] Calculated radial load

ft – Thermal correction factor Rn [lbs] Rated OHL

i – Gear ratio Rx [lbs] Radial OHL for load shifted from

shaft midpoint
I – Intermittence
S – Safety factor
2
Jc [Ib·ft ] Load moment of inertia
S.F. – Service factor
2
Jm [Ib·ft ] Mass moment of inertia for motor
ta [°C/ °F] Ambient temperature
Jr [Ib·ft2] Mass moment of inertia for gearbox
tf [min] Operating time under constant load
K – Acceleration factor of masses
tr [min] Rest time
Kr – Transmission element factor
W [ft×lb] Brake dissipated energy between
two successive air-gap adjustments
Tb [lb·in] Brake torque
Wmax [ft×lb] Maximum energy for each braking
T [lb·in] Torque operation

Tc [lb·in] Calculated torque x [in] Load application distance from shaft

shoulder
Tn [lb·in] Speed reducer rated torque
Z [1/h] Number of permitted starts in loaded
Tr [lb·in] Torque required conditions

n [rpm] Speed Zr [1/h] Number of starts

P [hp] Power Dynamic efficiency

Pc [hp] Calculated power

hd
Pn [hp] Motor rated power
Footnotes:
Pn [hp] Rated horsepower
1 Applies to input shaft

2
 NOMENCLATURE 1.4 THERMAL CAPACITY Pt

The value indicates the speed reducer thermal limit and

corresponds to the power transmission capacity under
1.2 TORQUE continuous duty at an ambient temperature of 20°C
[70°F] without using a supplementary cooling system.
For short operating periods with sufficiently long pauses
Nominal output torque Tn2 to allow the unit to cool, thermal power is not a factor
Torque transmitted at output shaft under uniform important and it does not need to be taken into consid-
load, referred to input speed n1 and corresponding eration.
output speed n2. For ambient temperature different from 20°C [70°F] and
It is calculated according to service factor S.F. = 1. intermittent duty, Pt value can be adjusted according to
thermal factor ft listed in table (A1), provided the follow-
ing condition is satisfied.
Application torque Tr2
Pr1 £ Pt x ft
This is torque corresponding to application require-
ments. It must be equal to or less than rated output
torque Tn2 for the gearmotor selected. Gear units A 10 through A 30 are not thermally limited
and the thermal verification does not apply.

Calculated torque Tc2

Torque value to be used for selecting the gearbox,
considering required torque Tr2 and service factor
S.F., and is obtained by:

T c2 = T r2 x S.F. £ T n2
(A0)

Pt [hp] [20 °C / 70 °F]

n1 = 1750 rpm n1 = 3500 rpm

A 10 2 6.4 5.4
1.3 POWER
A 20 2 8.0 7.2

Rated input horsepower Pn1 A 30 2 10.7 8.9

In the speed reducer selection charts, this is power
applicable at input shaft referred to speed n1 and A 41 2 13.4 11.7
considering a service factor S.F. = 1.
A 50 2 27 24.1

Output horsepower Pn2 A 60 2 36 31

Value represents rated HP as referred to speed reducer
output shaft. A 70 3 42 35

Pn2 = Pn1 x hd A 80 3 59 52
Tn2 x n 2
Pn2 = Pn2 in [hp]; Mn2 in [ib·in] A 90 3 86 76
63025

3
(A1)
1.7 SERVICE FACTOR S.F.
ft
The service factor is the numerical parameter that de-
Intermittent duty scribes the severity of the application. Its value re-
sults from the combination of the actual duty the gear-
ta max. Continuous box is operated at, the number of starts per hour and
Intermittence % (I)
°C [°F] duty the daily operating hours.
80 60 40 20 The graph (A2) here after comes handy when
calculating the actual value for the service factor:
40 [105] 0.8 1.1 1.3 1.5 1.6 1. Enter the chart with the starts per hour [Zr]
2. Intersect the K_ curve that applies for the appli-
30 [85] 0.85 1.3 1.5 1.6 1.8 cation
3. Read the service factor S.F. from the column
20 [70] 1.0 1.5 1.6 1.8 2.0
marked with the applicable hours per day [h/d]
50 [10] 1.15 1.6 1.8 2.0 2.3 Intermediate values can be obtained by interpolation.

(A2)
h /d
Starts per hour
24 16 8
Intermittence (I)% is obtained dividing operating time 1.9 1.8
2.0
under load [tf] by total time, expressed as a percent- 1.8 1.7
K3
1.9
age: 1.6
1.8
1.7 K2

tf
1.5
1.6
I= x 100 1.7
1.4
t f + tr SF 1.6
1.5
1.3
1.4 K1
1.2
1.5
1.3
1.1
1.4
1.2 1.0
1.3 1.1 0.9

1.2 1.0 0.8

0 25 50 75 100 125 150 175 200 225 250 275 300
Zr
1.5 EFFICIENCY h
Acceleration factor of masses K
Obtained from the relationship of output power P2 to
input power P1, according to the following equation: Used for establishing the service factor and obtained
from the following equation:
P2
h= Jc
P1 K=
Jm
Where:
Torque value Mn2 specified in this catalogue takes the
dynamic efficiency hd into account. Jc [Ib·ft2]
moment of inertia of the driven masses in proportion
to the speed of the applied motor
Jm [Ib·ft2]
motor moment of inertia
K1 uniform load
1.6 MASS MOMENT OF INERTIA Jr K £ 0.25
K2 moderate shock load
K£3
Values for the moment of inertia specified in the cata-
logue refer to gear unit input shaft. K3 heavy shock load
They are therefore related to motor speed, in the K £ 10
case of direct motor mounting. For values of K > 10, please contact our Technical Service.

4
1.8 SELECTION Application S.F.
Container
Main Hoist 3.00
AGMA Service Factor charting Boom Hoist 2.00
24hr service (continuous duty) Trolley Drive
Gantry Drive 3.00
Traction Drive 2.00
(A3) Mill Duty
Main Hoist 3.50
Application S.F. Auxiliary 3.50
Bridge Travel 3.00
AGITATORS Trolley Travel 3.00
Pure Liquids 1.25 Industrial Duty
Liquids & Solids 1.50 Main 3.00
Liquids - variable density 1.50 Auxiliary 3.00
BLOWERS Bridge Travel 3.00
Centrifugal 1.25 Trolley Travel 3.00
Lobe 1.50 CRUSHERS
Vane 1.50
Stone or Ore 2.00
BREWING AND DISTILLING
DREDGES
Bottling Machinery 1.25
Cable Reels 1.50
Brew Kettles - Continuous Duty 1.25
Conveyors 1.50
Cookers - Continuous Duty 1.25
Cutter Head Drives 2.00
Mash Tubs - Continuous Duty 1.25
Pumps 2.00
Scale Hopper - Frequent Starts 1.50
Screen Drives 2.00
CAN FILLING MACHINES 1.25 Stackers 1.50
CAR DUMPERS 2.00 Winches 1.50
CAR PULLERS 1.50 ELEVATORS
CLARIFIERS 1.25 Bucket 1.50
CLASSIFIERS 1.50 Centrifugal Discharge 1.25
CLAY WORKING MACHINERY Escalators 1.25
Brick Press 2.00 Freight 1.50
Briquette Machine 2.00 Gravity Discharge 1.25
Pug Mill 1.50 EXTRUDERS
COMPACTORS 2.00 General 1.50
COMPRESSORS Plastics
Centrifugal 1.25 Variable Speed Drive 1.50
Lobe 1.50 Fixed Speed Drive 1.75
Reciprocating, Multi-Cylinder 1.75 Rubber
Reciprocating, Single-Cylinder 2.00
Continuous Screw Operation 1.75
CONVEYORS - GENERAL PURPOSE Intermittent Screw Operation 1.75
includes Apron, Assembly, Belt, Bucket, Chain, FANS
Flight, Oven and Screw
Centrifugal 1.25
Uniformly Loaded or Fed 1.25 Cooling Towers 2.00
Heavy Duty - Not Uniformly Fed 1.50 Forced Draft 1.25
Severe Duty - Reciprocating or Shaker 2.00 Induced Draft 1.50
CRANES Industrial & Mine 1.50
Dry Dock FEEDERS
Main Hoist 2.50 Apron 1.50
Auxiliary Hoist 3.00 Belt 1.50
Boom Hoist 3.00 Disc 1.25
Slewing Hoist 3.00 Reciprocating 2.00
Traction Drive 3.00 Screw 1.50

5
 Application S.F. Application S.F.
FOOD INDUSTRY Reversing 2.00
Cereal Cooker 1.25 Slab Pushers 1.50
Dough Mixer 1.50 Shears 2.00
Meat Grinder 1.50 Wire Drawing 1.50
Slicers 1.50 Wire Winding Machine 1.50
GENERATORS AND EXITORS 1.25 METAL STRIP PROCESSING MACHINERY
HAMMER MILLS 2.00 Bridles 1.50
HOISTS Coilers & Uncoilers 1.25
Heavy Duty 2.00 Edge Trimmers 1.50
Medium Duty 1.50 Flatteners 1.50
Skip Hoist 1.50 Loopers (Accumulators) 1.25
Pinch Rolls 1.50
LUMBER INDUSTRY
Scrap Choppers 1.50
Barkers Shears 2.00
Spindle Feed 1.50 Slitters 1.50
Main Drive 1.75 MILLS, ROTARY TYPE
Conveyors Ball & Rod
Burner 1.50 Spur Ring Gear 2.00
Main or Heavy Duty 1.50 Helical Ring Gear 1.50
Main Log 2.00 Direct Connected 2.00
Re-saw, Merry-Go-Round 1.50
Slab 2.00 Cement Kilns 1.50
Transfer 1.50 Dryers & Coolers 1.50
Chains MIXERS, CEMENT 1.50
Floor 1.50 PAPER MILLS
Green 1.75 Agitator (Mixer) 1.50
Cut-Off Saws Agitator for Pure Liquors 1.25
Barking Drums 2.00
Chain 1.75
Barkers - Mechanical 2.00
Drag 1.75
Beater 1.50
Debarking Drums 2.00 Breaker Stack 1.25
Feeds Calendar 1.25
Edger 1.50 Chipper 2.00
Gang 1.75 Chip Feeder 1.50
Trimmer 1.50 Coating Rolls 1.25
Log Deck 1.75 Conveyors
Log Hauls - Incline - Well Type 1.75 Chip, Bark, Chemical 1.25
Log Turning Devices 1.75 Log (including Slab) 2.00
Planer Feed 1.50
Couch Rolls 1.25
Planer Tilting Hoists 1.50
Rolls - Live-off brg. - Roll Cases 1.75 Cutter 2.00
Sorting Table 1.50 Cylinder Molds 1.25
Tipple Hoist 1.50 Dryers
Transfer Paper Machine 1.25
Chain 1.75 Conveyor Type 1.25
Craneway 1.75 Embosser 1.25
Tray Drives 1.50 Extruder 1.50
Veneer Lathe Drives 1.50 Fourdrinier Rolls 1.25
(includes Lump breaker, dandy roll,
METAL MILLS wire turning, and return rolls)
Draw Bench Carriage and Main Drive 1.50 Jordan 1.50
Runout Table Kiln Drive 1.50
Non-reversing 1.50 Mt. Hope Roll 1.25
Group Drives 1.50 Paper Rolls 1.25
Individual Drives 2.00 Platter 1.50

6
Application S.F. Application S.F.
Presses - Felt & Suction 1.25 Cracker - 2 corrugated rolls 2.00
Pulper 2.00 Holding, Feed & Blend Mill - 2 rolls 1.25
Pumps - Vacuum 1.50 Refiner - 2 rolls 1.50
Reel (Surface Type) 1.25 Calender 1.50
Screens SAND MULLER SEWAGE DISPOSAL 1.50
Chip 1.50 EQUIPMENT
Rotary 1.50 Bar Screens 1.25
Vibrating 2.00 Chemical Feeders 1.25
Size Press 1.25 Dewatering Screens 1.50
Super Calender 1.25 Scum Breakers 1.50
Thickener (AC Motor) 1.50 Slow or Rapid Mixers 1.50
Thickener (DC Motor) 1.25 Sludge Collectors 1.25
Washer (AC Motor) 1.50 Thickener 1.50
Washer (DC Motor) 1.25 Vacuum Filters 1.50
Wind and Unwind Stand 1.25 SCREENS
Winders (Surface Type) 1.25 Air Washing 1.25
Yankee Dryers 1.25 Rotary - Stone or Gravel 1.50
PLASTICS INDUSTRY - PRIMARY PROCESSING Traveling Water Intake 1.25
Intensive Internal Mixers SUGAR INDUSTRY
Batch Mixers 1.75 Beet Slicer 2.00
Continuous Mixers 1.50 Cane Knives 1.50
Batch Drop Mill - 2 smooth rolls 1.25 Crushers 1.50
Continuous Feed, Holding & Blend Mill 1.25 Mills (low speed end) 1.75
Calender 1.50 TEXTILE INDUSTRY
PLASTICS INDUSTRY - SECONDARY PROCESSING Batchers, 1.50
Blow Molder 1.50 Calenders 1.50
Coating 1.25 Cards 1.50
Film 1.25 Dry Cans 1.50
Pipe 1.25 Dyeing Machinery 1.50
Pre-Plasticizer 1.50 Looms 1.50
Rods 1.25 Mangles 1.50
Sheet 1.25 Nappers 1.50
Tubing 1.50 Pads 1.50
PULLER - BARGE HAUL 1.50 Slashers 1.50
PUMPS Soapers 1.50
Centrifugal 1.25 Spinners 1.50
Proportioning 1.50 Tenter Frames 1.50
Washers 1.50
Reciprocating Winders 1.50
Single Acting, 3 or more cylinders 1.50
Double Acting, 2 or more cylinders 1.50
Rotary
Gear Type 1.25
Lobe 1.25
Vane 1.25
RUBBER INDUSTRY
Intensive Internal Mixers
Batch Mixers 1.75
Continuous Mixers 1.50
Mixing Mill
2 smooth rolls 1.50
1 or 2 corrugated rolls
Batch Drop Mill - 2 smooth rolls 1.50

7
Recommended procedure for correct selection of (A5)
drive unit:
Duty

Selecting a gearmotor S2 S3* S4 - S8

Cycle duration Intermittence
A) Determine service factor S.F. according to type of [min] (I) Please
duty (factor K), number of starts per hour Zr and consult
10 30 60 25% 40% 60%
hours of operation. factory
fm 1.35 1.15 1.05 1.25 1.15 1.1
B) Once torque Tr2, speed n2 and dynamic efficiency hd * Cycle duration, in any event, must be 10 minutes or less. If it is lon-
are known, input power can be calculated as fol- ger, please contact our Technical Service Department.
lows:
Intermittence:

tf
Tr2 (Ib × in) x n 2 (rpm) I= x 100
Pr1(hp) = tf + tr
63,025 x h d
tf = operating time at constant load
tr = rest time
Values for hd for the different sizes of speed reducer
are indicated in table (A4) below: Next, according to output speed n2, select a
gearmotor featuring a safety factor S greater than or
equal to service factor S.F.
(A4)
S ³ S.F.
Reductions
The gearmotor selection charts features combination
2 3 4 with 2, 4 and 6 pole motors.
If motors with different speed shall be used, refer to the
hd 0.95 0.93 0.91
selection procedure for speed reducers and choose the
most suitable gear unit.
For applications such as hoisting and travelling, con-
tact our Technical Service Department.
C) Consult the gearmotor selection charts and locate
the table corresponding to power

Pn ³ Pr1 Selecting a speed reducer

with a motor adapter
Unless otherwise specified, power Pn of motors indi-
cated in the catalogue refers to continuous duty S1.
For motors used in conditions other than S1, the type A) Determine service factor S.F. based on application.
of duty required by reference to CEI 2-3/IEC 60034-1 See pages 5 - 7.
Standards must be mentioned.
For duties from S2 to S8 in particular, and for IEC B) Assuming the required output torque for the appli-
motor frame 132 or smaller, extra power can be ob- cation Tr2 is known, the calculated torque can be
tained with respect to continuous duty, consequently defined as:
the following condition must be satisfied:
Tc2 = Tr2 x S.F.
P
Pn ³ r1
fm C) The gear ratio is calculated according to requested
output speed n2 and the drive input speed n1

The adjusting duty factor fm can be obtained from n1

i=
chart (A5). n2

8
 Once the torque Tc2 and gear ratio [i] are calculated D) Thrust loads
consult the speed reducer rating chart for the actual Thrust loads, if applicable, must also be compared
drive speed n1 and select the unit that features a to the permitted values indicated in the catalogue.
torque rating Tn2 that equals or exceeds the compu- In the event of extremely high thrust loads, or a
tational torque Tc2: combination of thrust and radial loads, contact our
Technical Service for advise.
Tn2 ³ Tc2
E) Electric motors
If an electric motor, with either a NEMA or a IEC
For duties with considerable number of starts per hour,
flange, is going to be fitted onto the captioned gear
factor Z must be considered (it can be sorted from the
unit, check that matching is feasible at chapter “Mo-
motor rating chart). Factor Z defines the maximum
tor availability”.
number of starts for the application under consider-
ation.

1.9 VERIFICATIONS 1.10 INSTALLATION

After the selection of the speed reducer, or gearmotor, The following installation instructions must be followed:
is complete:
A) Make sure that the speed reducer is adequately
secured to avoid vibrations. If shocks, prolonged
A) Thermal capacity overloading, or the possibility of locking are ex-
Make sure that the thermal capacity of the speed re- pected, install hydraulic couplings, clutches, torque
ducer is equal to or higher than power required by limiters, etc.).
the application. If this condition is not verified, select
a larger speed reducer or apply a supplementary B) Prior to painting the gear unit,, the outer face of the
cooling system. oil seals must be protected to prevent the solvent
drying out the rubber, thus jeopardizing the sealing
B) Maximum torque function.
The maximum torque (intended as momentary peak
load) applicable to the speed reducer must not, in C) Contact surfaces must be cleaned and treated with
general, exceed 200% of rated torque Tn2. Therefore, suitable protective products before mounting to avoid
check that this limit is not exceeded, using suitable oxidation and, as a result, seizure of parts.
torque limiting devices, if necessary.
For three-phase two speed motors, it is important to D) Before starting up the machine, make sure that oil
pay attention to switching torque generated (from level is correct for the actual mounting position, and
high to low speed), because it could be significantly that viscosity is suitable for the specific duty. See ta-
higher than maximum torque. ble (B1).

C) Radial loads
Check that forces applying on input and/or output
shafts are within permitted catalogue values. If they
are higher, select a larger speed reducer or change
bearing arrangement.
Remember that all values listed in the catalogue re-
fer to loads acting at mid-point of the shaft. The
permissible radial load value should be adjusted if
the radial load is not acting at mid point of shaft.
See para 2.8.

9
1.11 STORAGE
Observe the following instructions to ensure correct
storage of products:

A) Do not store outdoors, in areas exposed to

weather or with excessive humidity.

B) Always place boards, wood, or other material be-

tween the products and the floor. The gearbox
should not have direct contact with the floor.

C) For long term storage (over 60 days), all machined

surfaces such as flanges, shafts and couplings must
be protected with a suitable rust inhibiting product
(Mobilarma 248 or equivalent).

D) The following measures must be taken when prod-

ucts are stored for a period exceeding 6 months:
For life lubricated products, the machined areas
must be greased to prevent oxidation.
In addition to above, products originally supplied w/o
oil must be positioned with the breather plug at the
highest point, and filled with oil.
Before operating the speed reducer, restore the cor-
rect quantity of oil.

1.12 MAINTENANCE
Speed reducers A 10 throught A 30 are lubricated
and do not require periodical oil change.
For larger speed reducers, the first oil change must
take place after about 300 hours of operation, flush-
ing the interior of the unit using suitable detergents.
Do not mix mineral oils with synthetic oils.
Check oil periodically and restore the level, if neces-
sary.

10
2.0 BEVEL-HELICAL GEARMOTORS

A SERIES

11
2.1 ORDERING NUMBERS
Speed reducer designation

A 30 2 NUH F1A 76.5 S1 B3 .....

OPTIONS

MOUNTING POSITION
B3 (default), B6, B7, B8, VA, VB
INPUT OPTIONS
NHS for speed reducer with solid input shaft (inch dims.)
HS for speed reducer with solid input shaft (metric dims.)
P + IEC frame size for gear head with IEC motor adapter
S + motor size for integral gearmotor
Specify for NEMA inputs:
56C 56C
140TC 143TC and 145TC
180TC 182TC and 184TC
N+ 210TC for motors: 213TC and 215TC
250TC 254TC and 256TC
280TC 284TC and 286TC
320TC 324TC and 326TC

GEAR RATIO
F = flange
1 = R.H. mount; 2 = L.H. mount
A, B, C = size of flange

VERSION

‚ 
shaft
dims.

NUH: hollow shaft NUL NUR NUD

— inch
(A 10...A 60) (A 10...A 60) (A 10...A 60) (A 10...A 60)

UH_: hollow shaft UR UD US: shrink disc

— metric
(A 70...A 90) (A 70...A 90) (A 70...A 90) (A 10...A 90)

REDUCTIONS
2, 3, 4

FRAME SIZE
10, 20, 30, 41, 50, 60, 70, 80, 90

SERIES
A = bevel-helical

12
 Bonfiglioli motor

MOTOR BRAKE

M 1LA 4 230/460-60 IP54 CLF ..... W FD 15 R SB 220 SA ....

OPTIONS

BRAKE SUPPLY

AC/DC RECTIFIER
NB, NBR, SB, SBR

BRAKE HAND RELEASE (optional)

R, RM

BRAKE TORQUE [specify Nm!]

[1 ft • lb = 1.356 Nm]

BRAKE TYPE
FD (DC brake)
FA (AC brake)

TERMINAL BOX
W (default), N, S, E

MOUNTING
blank for compact motor
B5 for IEC motor

INSULATION CLASS
CL F default

PROTECTION CLASS
IP 55 standard (IP 54 standard for brake motors)

VOLTAGE - FREQUENCY

NUMBER OF POLES

MOTOR FRAME SIZE

05A...5LA - integral motor
63A...225S4 - IEC style motor

TYPE OF MOTOR
M = AC, 3-ph, integral style
BN = AC, 3-ph, IEC face motor
NEMA motors to be specified thru their ordering numbers

13
2.2 DESIGN ADVANTAGES 2.4 SPEED REDUCER OPTIONS
The main design characteristics are: AL, AR
Anti-run back device.
• modularity The gear units the device can be specified for and the
direction of free rotation are described at chapter 2.11
• compact design
SO
• universal mounting
Gearboxes A 10, A 20, A 30, are supplied without oil.
• high efficiency
LO
• low noise Gearboxes A 41, A 50, A 60, A 70, A 80, A 90, usually
• gears in hardened and case-hardened steel supplied without oil, to be factory filled with synthetic oil
• aluminium housing for sizes 10, 20, 30, unpainted, currently used by BONFIGLIOLI RIDUTTORI according
high strength painted cast-iron housings for larger to the mounting position specified.
sizes. DV
• input and output shafts in high grade steel Two oil seals on input shaft.
(Available only for compact gearmotors).
VV
Viton® oil seal on input shaft.
2.3 VERSIONS PV
All oil seals in Viton® material.
Available version for A series gearbox and gearmotors
are illustrated below.

Terminal box location

NUL (inch series) Location of motor terminal box can be specified by view-
ing the motor from the fan side; default position is high-
lighted in bold (W).

Angular position of the brake release lever

UR (metric series)
NUR (inch series)
Unless otherwise specified, brake motors have the man-
ual device side located, 90° apart from terminal box.
Different angles can be specified through the relevant
options available.
UD (metric series)
NUD (inch series)
2.5 SYMBOLS

UH (metric series) Gearmotor with compact motor. Gearmotor with motor adapter.
NUH (inch series)

Gearbox with NEMA input. Gearbox with solid input shaft.

2x 3x 4x
US (metric series)
2 Reduction 3 Reduction 4 Reduction The symbol shows the
page the information
can be sorted from.

14
 (B1)
2.6 LUBRICATION
Ambient temp. Ambient temp.
0 - 20 °C 20 - 40 °C
Speed reducer size A 10...A 30 are supplied with life lubri- [32 - 70 °F] [70 - 104 °F]
Duty
cation and do not have oil filling, level, and drain plugs.
Mineral oil Synthetic oil Mineral oil Synthetic oil
These long-life lubricated units are capable of operating at ISO VG ISO VG ISO VG ISO VG
an ambient temperature range of 0 °C to +50 °C [32 to
Light duty 150 150 220 220
122 °F]. For temperatures below 0 °C [32 °F], contact our
Medium duty 150 150 320 220
Technical Service.
Speed reducers for which the SO options is specified Heavy duty 220 220 460 320
come without oil and must be filled by the user prior to be
(B2)
put into operation.
Oil temperature Oil change interval [hours]
In this case refer to charts (B1) and (B2) for the most ap-
°C [°F] Mineral oil Synthetic oil
propriate type of oil and relevant change interval.
< 65
Customers must always advise mounting position to ensure 8000 25000
[< 150 °F]
the correct arrangement of the filling, level and drain plugs.
65 - 80
[150 °F - 175 °F] 4000 15000
Periodical oil changes are not required for sizes A 10...A 30 80 - 95
[175 °F - 200 °F] 2000 12500
as they are lubricated for life with synthetic oil.
(B3)
Oil quantity
Mounting positions
B3 B6 B7 B8 VA VB
0.37 0.37 0.37 0.37 0.37 0.37
A 10 2
1.4 1.4 1.4 1.4 1.4 1.4
0.61 0.61 0.61 0.61 0.61 0.61
A 20 2
2.3 2.3 2.3 2.3 2.3 2.3
0.69 0.69 0.69 0.69 0.69 0.69
A 20 3
2.6 2.6 2.6 2.6 2.6 2.6
0.84 0.84 0.84 0.84 0.84 0.84
A 30 2
3.2 3.2 3.2 3.2 3.2 3.2
0.95 0.95 0.95 0.95 0.95 0.95
A 30 3
3.6 3.6 3.6 3.6 3.6 3.6
1.06 1.08 1.08 1.24 1.37 1.16
A 41 2
4.0 4.1 4.1 4.7 5.2 4.4
1.06 1.06 1.06 1.24 1.61 1.03
A 41 3
4.0 4.0 4.0 4.7 6.1 3.9
1.29 2.14 1.24 2.22 2.90 2.43
A 50 2
4.9 8.1 4.7 8.4 11 9.2
1.35 2.14 1.24 2.22 2.90 2.43
A 50 3
5.1 8.1 4.7 8.4 11 9.2
1.66 2.16 1.40 2.19 3.43 2.40
A 50 4
6.3 8.2 5.3 8.3 13 9.1
1.80 2.14 3.17 3.96 4.75 3.96
A 60 2
6.8 8.1 12 15 18 15
1.80 2.14 3.17 3.96 4.75 3.96
A 60 3
6.8 8.1 12 15 18 15
1.90 2.90 1.95 4.22 5.02 3.70
A 60 4
7.2 11 7.4 16 19 14
2.64 3.70 2.64 3.96 5.28 3.70
A 70 3
10 14 10 15 20 14
3.43 3.70 2.64 3.96 6.07 3.70
A 70 4
13 14 10 15 23 14
3.96 5.81 3.96 6.86 9.24 5.81
A 80 3
15 22 15 26 35 22
5.28 5.81 3.96 6.86 10.30 5.81
A 80 4
20 22 15 26 39 22
8.18 9.24 9.77 11.62 17.42 10.30
A 90 3
31 35 37 44 66 39
10.82 9.24 9.77 11.62 19.27 10.30
A 90 4
41 35 37 44 73 39
gallons
Life lubricated Quantities are
litres
15
 A 10...A 30

2.7 MOUNTING POSITION AND TERMINAL BOX SPECIFICATION

Fill / breather plug Level plug Drain plug

P (IEC)
Input: HS N (NEMA) S

B3

2x

W E

S 3x

W = Default

B6

2x

N S 3x
W

W = Default

B7

2x

S N 3x
E

W = Default

16
A 10...A 30

P (IEC)
Input: HS N (NEMA) S

B8

2x

E W

N 3x

W = Default

VA

2x

N S 3x
W

W = Default

VB

2x

S N

3x

W = Default

17
 A 41...A 60

P (IEC)
Input: HS N (NEMA) S

B3 (41-60) (50) (41-60) (50) (41-60) (50)

(A41-A50-A60)

2x

3x
(A50-A60)

(41-60) (50) (41-60) (50) (41-60) (50)

(A41)
N

W E 3x
S
(60) (50) (60) (50)
4x
(60)
(A50-A60)
(41-50) (41) (41)
W = Default

B6 (41-60) (41-60) (41-60)

(50) (50) (50)

(A41-A50-A60)

2x

3x
(A50-A60)

(41-60) (41-60) (41-60)

(50) (50) (50)
E (A41)

N S 3x
(50) (50) (50)
W

(41-60) (60) (60) 4x

(A50-A60)
W = Default

B7 (60)
(41)
(60)
(41)
(60)
(41)

(A41-A50-A60)
(50) (50) (50)
2x

3x
(A50-A60)
(41-60) (50) (41-60) (50) (41-60) (50)
(41-50)
(41) (41)
(60) (60) (A41)
W (60)
(50)
(50) 3x
S N
(50) (50) (50)
E
4x
(41-60) (41-60) (41-60) (A50-A60)

W = Default (41-50) (60) (41-50) (60) (41-50) (60)

18
A 41...A 60

P (IEC)
Input: HS N (NEMA) S

B8
(50-60) (50-60) (50-60) (A41-A50-A60)

2x
(41) (41) (41)

3x
(A50-A60)

(50) (41-60) (50) (41-60) (50) (41-60)

S (50-60) (50-60) (50-60) (A41)

E W 3x
(41) (41) (41)
N
4x
(A50-A60)

W = Default (50) (41-60) (50) (41-60) (50) (41-60)

VA
(A41-A50-A60)

2x

3x
(A50-A60)

(60) (41-50) (50-60) (41) (50-60) (41) (A41)

3x
E

N S
4x
W
(A50-A60)
W = Default

VB
(A41-A50-A60)

2x

3x
(A50-A60)

S N

E (A41)

3x
(50)
(50) (50) 4x
(60) (A50-A60)
(60) (60)
W = Default

19
 A 70...A 90

P (IEC)
Input: HS N (NEMA) S

B3

3x

W E

S 4x

W = Default

B6
(80) (80) (80)

70-90
3x

E (80) (80) (80)

N S

W 70-90 4x

W = Default

B7
(80) (80) (80)

3x

W (80) (80) (80)

S N

E 4x

W = Default

20
A 70...A 90

P (IEC)
Input: HS N (NEMA) S

B8

3x

E W

N 4x

W = Default

VA

3x

E 4x
N S

W
W = Default

VB

3x
(80)

(70-90)

S N

4x
(90)
(70-80)
W = Default

21
 Rn1, Rn2 = permitted OHL on shaft
2.8 OVERHUNG LOADS mid-point [Ibs] (radial load table)
a = load location factor
Input and output shaft of speed reducer can be subject b = load location factor
to loading generated by the transmission keyed on the c = load location factor
shaft itself. x = distance of load from shaft shoulder [in]
Overhung load can be calculated with the following for-
mula where all factors are determined at shaft under load location factors a, b, c are shown in table (B6).
study.
[N.B. (1) = input shaft; (2) = output shaft] (B5)
2 x T x Kr
Rc =
d

Rc = overhung load in [lbs]

T = torque in [lb·in]
d = pitch diameter in inches of sprocket, pinion, sheave
or pulley
Kr =transmission element factor
Sprocket (single or multiple strand) ............. 1.0
Spur or helical pinion ................................... 1.25
V-belt sheave ............................................... 1.50 (B6)
Flat belt pulley .............................................. 2.50
Load location factors [in]
Output shaft Input shaft
a) load Rc1 or Rc2 applied at midpoint of shaft as indi-
cated in table (B4). a b c a b c
This value can be directly compared with rated OHL ca- A 102 4.8 4.0 23.6 0.8 0 11.8
pacity by observing the condition:
A 202 5.9 4.7 29.5 1.6 0.8 13.8

Rc1 £ Rn1 ; Rc2 £ Rn2 A 203 5.9 4.7 29.5 0.8 0 11.8

(B4) A 302 6.6 5.4 35.4 1.5 0.7 13.8

A 303 6.6 5.4 35.4 0.8 0 11.8

A 412 7.8 6.2 41.3 1.9 1.0 17.7

A 413 7.8 6.2 41.3 1.6 0.8 13.8

A 502 - A503 9.5 7.9 51.2 1.9 1.0 17.7

A 504 9.5 7.9 51.2 1.5 0.7 13.8

A 602 - A603 9.5 7.5 61.0 2.2 1.0 23.6

A 604 9.5 7.5 61.0 1.9 1.0 17.7

b) load applied at distance "x" from shaft shoulder as
shown in table (B5). A 703 11.6 9.1 74.8 3.4 1.2 39.4
Conversion to the new permitted overhung load values
A 704 11.6 9.1 74.8 1.9 1.0 17.7
Rx1 and Rx2 is obtained from the following equation:
A 803 13.6 11.0 94.5 3.4 1.2 39.4
a a
Rx1 = Rn1 x ; Rx2 = Rn2 x
b + "x" b + "x" A 804 13.6 11.0 94.5 1.9 1.0 17.7

A 903 17.0 12.9 122.4 4.6 1.8 55.1

as long as L < "x" < c
2 A 904 17.0 12.9 122.4 1.9 1.0 17.7

22
 (B7)
Overhung load capacity of
output shaft, Rn2
Rated values for radial load referred to mid-point of the
output shaft are listed in the gearmotor and speed re-
ducer rating charts. They are based on transmitted
torque T2 and rated torque Tn2 respectively and for the
most unfavourable condition as far as the load angle
and rotation direction.
If permitted values are below required values, please
consult our Technical Service Department reporting the
A102 - A202 - A302 - A412 - A502 - A602
load angle and shaft rotation direction.
A504 - A603 - A704 - A804 - A904

Overhung load capacity of

input shaft, Rn1
These values which are shown in the speed reducer se-
lection charts refer to input speed and are calculated at
mid-point of the input shaft.
If permitted values are below required values, please
consult our Technical Service reporting load orientation
and shaft rotation direction. A203 - A303 - A413 - A503 - A604
A703 - A803 - A903

Thrust loads, An1 An2

2.10 ANTI-RUN BACK DEVICE
Maximum permitted thrust loads can be calculated as
follows: An anti-run back device is available upon request to al-
low rotation of the output shaft in one direction only (op-
tion AL-AR).
An1 = Rn1 • 0.2 Table (B8) shows the models in which the anti-run back
An2 = Rn2 • 0.2 device can be installed. Please specify in the order the
required rotation direction through option AL or AR (ta-
ble B9) in the gearbox or motor designation. Default set-
If thrust load exceeds permitted value, consult our
ting is as per rotation AR.
Technical Service.

(B8)
Type

A102 A202
A302 A412 A503 A603 A703 A803 A903
A203 A303 A413 A502 A504 A602 A604 A704 A804 A904

• • • • • •
2.9 SHAFT ARRANGEMENT
• Anti-run back device can be fitted to compact motor only

Table (B7) shows standard directions of rotation for 2, 3 Anti-run back device can be fitted either onto compact motor
and 4 stage helical-bevel gearboxes. or onto the gearbox

23
(B9)

2.11 INSTALLATION INSTRUCTIONS

Schemes in table (B10) show the 3 possible patterns for for the hexagonal head bolt to be used. Besides, for an
bolting the A units onto the machine. easier installation, we suggest to use a wrench of the
For each of these cases, table (B11) indicates the size type shown in table (B10).

(B10)

À Á Â
(B11)
Bolts pattern

À Á Â DL (mm)
A 10 M8 x 25 M8 x 20 M8 x... 20
A 20 M8 x 25 M8 x 20 M8 x... 20
A 30 M10 x 30 M10 x 25 M10 x... 25
A 41 M12 x 35 M12 x 30 M12 x... 30
A 50 M14 x 45 M14 x 40 M14 x... 35
A 60 M16 x 50 M16 x 45 M16 x... 40
A 70 M20 x 60 M20 x 55 M20 x... 45
A 80 M24 x 70 M24 x 65 M24 x... 55

24
2.12 GEARMOTOR RATING CHARTS

0.16 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

309 31 40.4 5.5:1 680 A102_5.5 S05 + M05A4 P63 + BN63A4 N56C 76...79
234 40 30.6 7.2:1 740 A102_7.2 S05 + M05A4 P63 + BN63A4 N56C 76...79
201 47 26.3 5.5:1 780 A102_5.5 S05 + M05B6 P63 + BN63B6 N56C 76...79
176 54 23.0 9.6:1 820 A102_9.6 S05 + M05A4 P63 + BN63A4 N56C 76...79
160 59 22.4 10.6:1 840 A102_10.6 S05 + M05A4 P63 + BN63A4 N56C 76...79

137 69 18.0 12.3:1 890 A102_12.3 S05 + M05A4 P63 + BN63A4 N56C 76...79
121 78 17.0 13.9:1 920 A102_13.9 S05 + M05A4 P63 + BN63A4 N56C 76...79
104 91 14.6 10.6:1 970 A102_10.6 S05 + M05B6 P63 + BN63B6 N56C 76...79
91 104 12.7 18.6:1 1010 A102_18.6 S05 + M05A4 P63 + BN63A4 N56C 76...79
79 120 11.1 13.9:1 1060 A102_13.9 S05 + M05B6 P63 + BN63B6 N56C 76...79

71 133 10.0 23.8:1 1090 A102_23.8 S05 + M05A4 P63 + BN63A4 N56C 76...79
59 160 8.3 28.6:1 1160 A102_28.6 S05 + M05A4 P63 + BN63A4 N56C 76...79
48 197 6.7 35.1:1 1230 A102_35.1 S05 + M05A4 P63 + BN63A4 N56C 76...79
37 255 5.2 45.4:1 1240 A102_45.4 S05 + M05A4 P63 + BN63A4 N56C 76...79
33 287 4.6 51.3:1 1240 A102_51.3 S05 + M05A4 P63 + BN63A4 N56C 76...79

31 303 4.4 35.1:1 1240 A102_35.1 S05 + M05B6 P63 + BN63B6 N56C 76...79
25.6 370 3.6 65.9:1 1240 A102_65.9 S05 + M05A4 P63 + BN63A4 N56C 76...79
22.1 429 3.1 76.4:1 1240 A102_76.4 S05 + M05A4 P63 + BN63A4 N56C 76...79
21.5 442 3.0 51.3:1 1240 A102_51.3 S05 + M05B6 P63 + BN63B6 N56C 76...79
18.4 514 2.2 91.6:1 1240 A102_91.6 S05 + M05A4 P63 + BN63A4 N56C 76...79

18.3 518 3.4 92.3:1 1390 A202_92.3 S05 + M05A4 P63 + BN63A4 N56C 80...83
16.7 568 2.3 65.9:1 1240 A102_65.9 S05 + M05B6 P63 + BN63B6 N56C 76...79
14.4 658 2.0 76.4:1 1240 A102_76.4 S05 + M05B6 P63 + BN63B6 N56C 76...79
14.0 654 2.8 120.5:1 1390 A203_120.5 S05 + M05A4 P63 + BN63A4 N56C 80...83
13.8 688 2.7 79.9:1 1390 A202_79.9 S05 + M05B6 P63 + BN63B6 N56C 80...83

12.0 790 1.5 91.6:1 1240 A102_91.6 S05 + M05B6 P63 + BN63B6 N56C 76...79
11.9 796 2.2 92.3:1 1390 A202_92.3 S05 + M05B6 P63 + BN63B6 N56C 80...83
11.6 794 2.6 146.1:1 1390 A203_146.1 S05 + M05A4 P63 + BN63A4 N56C 80...83
9.5 968 2.2 178.3:1 1390 A203_178.3 S05 + M05A4 P63 + BN63A4 N56C 80...83
9.5 969 3.1 178.5:1 2160 A303_178.5 S05 + M05A4 P63 + BN63A4 N56C 84...87

7.8 1176 2.7 216.6:1 2160 A303_216.6 S05 + M05A4 P63 + BN63A4 N56C 84...87
7.6 1202 1.8 221.3:1 1390 A203_221.3 S05 + M05A4 P63 + BN63A4 N56C 80...83
6.5 1414 1.6 260.5:1 1390 A203_260.5 S05 + M05A4 P63 + BN63A4 N56C 80...83
6.2 1474 2.3 271.5:1 2160 A303_271.5 S05 + M05A4 P63 + BN63A4 N56C 84...87
5.4 1708 2.0 314.6:1 2160 A303_314.6 S05 + M05A4 P63 + BN63A4 N56C 84...87

5.2 1760 4.3 324.2:1 3370 A413_324.2 S05 + M05A4 P63 + BN63A4 N56C 88...91
5.1 1789 1.2 329.4:1 1390 A203_329.4 S05 + M05A4 P63 + BN63A4 N56C 80...83
4.5 2046 3.7 376.8:1 3370 A413_376.8 S05 + M05A4 P63 + BN63A4 N56C 88...91
4.2 2176 1.5 400.8:1 2160 A303_400.8 S05 + M05A4 P63 + BN63A4 N56C 84...87
4.2 2189 3.4 262.5:1 3370 A413_262.5 S05 + M05B6 P63 + BN63B6 N56C 88...91

3.5 2624 1.4 314.6:1 2160 A303_314.6 S05 + M05B6 P63 + BN63B6 N56C 84...87

25
 0.16 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

3.4 2704 2.8 324.2:1 3370 A413_324.2 S05 + M05B6 P63 + BN63B6 N56C 88...91
2.9 3144 2.4 376.8:1 3370 A413_376.8 S05 + M05B6 P63 + BN63B6 N56C 88...91
2.7 3379 3.9 621.3:1 4500 A504_621.3 P63 + BN63A4 N56C 92...95
2.3 3850 3.4 707.9:1 4500 A504_707.9 P63 + BN63A4 N56C 92...95
2.1 4320 3.1 529.5:1 4500 A504_529.5 P63 + BN63B6 N56C 92...95

1.8 5069 2.6 621.3:1 4500 A504_621.3 P63 + BN63B6 N56C 92...95
1.6 5776 2.3 707.9:1 4500 A504_707.9 P63 + BN63B6 N56C 92...95
1.5 6163 4.0 755.4:1 6740 A604_755.4 P63 + BN63B6 N56C 96...99
1.4 6349 2.1 778.2:1 4500 A504_778.2 P63 + BN63B6 N56C 92...95
1.2 7559 5.9 926.5:1 11200 A704_926.5 P63 + BN63B6 N56C 100...103

1.0 8746 5.1 1072:1 11200 A704_1072 P63 + BN63B6 N56C 100...103
0.82 10982 4.0 1346:1 11200 A704_1346 P63 + BN63B6 N56C 100...103
0.64 13992 3.2 1715:1 11200 A704_1715 P63 + BN63B6 N56C 100...103

0.25 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

306 48 25.6 5.5:1 680 A102_5.5 S05 + M05B4 P63 + BN63B4 N56C 76...79
232 64 19.4 7.2:1 740 A102_7.2 S05 + M05B4 P63 + BN63B4 N56C 76...79
201 74 16.8 5.5:1 780 A102_5.5 S1 + M1SC6 P71 + BN71A6 N56C 76...79
174 85 14.5 9.6:1 810 A102_9.6 S05 + M05B4 P63 + BN63B4 N56C 76...79
158 94 14.2 10.6:1 840 A102_10.6 S05 + M05B4 P63 + BN63B4 N56C 76...79

136 109 11.4 12.3:1 880 A102_12.3 S05 + M05B4 P63 + BN63B4 N56C 76...79
120 124 10.7 13.9:1 910 A102_13.9 S05 + M05B4 P63 + BN63B4 N56C 76...79
114 129 9.6 9.6:1 930 A102_9.6 S1 + M1SC6 P71 + BN71A6 N56C 76...79
104 142 9.3 10.6:1 960 A102_10.6 S1 + M1SC6 P71 + BN71A6 N56C 76...79
90 165 8.1 18.6:1 1000 A102_18.6 S05 + M05B4 P63 + BN63B4 N56C 76...79

79 188 7.1 13.9:1 1040 A102_13.9 S1 + M1SC6 P71 + BN71A6 N56C 76...79
70 211 6.3 23.8:1 1080 A102_23.8 S05 + M05B4 P63 + BN63B4 N56C 76...79
58 253 5.2 28.6:1 1140 A102_28.6 S05 + M05B4 P63 + BN63B4 N56C 76...79
48 311 4.3 35.1:1 1210 A102_35.1 S05 + M05B4 P63 + BN63B4 N56C 76...79
46 320 4.1 23.8:1 1230 A102_23.8 S1 + M1SC6 P71 + BN71A6 N56C 76...79

37 403 3.3 45.4:1 1240 A102_45.4 S05 + M05B4 P63 + BN63B4 N56C 76...79
33 455 2.9 51.3:1 1240 A102_51.3 S05 + M05B4 P63 + BN63B4 N56C 76...79
31 473 2.8 35.1:1 1240 A102_35.1 S1 + M1SC6 P71 + BN71A6 N56C 76...79
26.4 560 3.9 63.1:1 1390 A202_63.1 S05 + M05B4 P63 + BN63B4 N56C 80...83
25.3 585 2.3 65.9:1 1240 A102_65.9 S05 + M05B4 P63 + BN63B4 N56C 76...79

21.9 678 2.0 76.4:1 1240 A102_76.4 S05 + M05B4 P63 + BN63B4 N56C 76...79
20.9 708 2.6 79.9:1 1390 A202_79.9 S05 + M05B4 P63 + BN63B4 N56C 80...83

26
 0.25 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

18.2 813 1.4 91.6:1 1240 A102_91.6 S05 + M05B4 P63 + BN63B4 N56C 76...79
18.1 819 2.2 92.3:1 1390 A202_92.3 S05 + M05B4 P63 + BN63B4 N56C 80...83
17.1 865 3.1 97.5:1 2160 A302_97.5 P63 + BN63B4 N56C 84...87
14.4 1029 1.3 76.4:1 1240 A102_76.4 S1 + M1SC6 P71 + BN71A6 N56C 76...79
14.4 1030 3.0 76.5:1 2160 A302_76.5 S1 + M1SC6 P71 + BN71A6 N56C 84...87

13.9 1034 2.6 120.5:1 2160 A303_120.5 S05 + M05B4 P63 + BN63B4 N56C 84...87
13.9 1035 1.8 120.5:1 1390 A203_120.5 S05 + M05B4 P63 + BN63B4 N56C 80...83
13.8 1075 1.7 79.9:1 1390 A202_79.9 S1 + M1SC6 P71 + BN71A6 N56C 80...83
11.9 1243 1.4 92.3:1 1390 A202_92.3 S1 + M1SC6 P71 + BN71A6 N56C 80...83
11.4 1255 1.6 146.1:1 1390 A203_146.1 S05 + M05B4 P63 + BN63B4 N56C 80...83

11.1 1294 2.3 150.7:1 2160 A303_150.7 S05 + M05B4 P63 + BN63B4 N56C 84...87
9.4 1531 1.4 178.3:1 1390 A203_178.3 S05 + M05B4 P63 + BN63B4 N56C 80...83
9.4 1533 2.0 178.5:1 2160 A303_178.5 S05 + M05B4 P63 + BN63B4 N56C 84...87
7.7 1859 1.7 216.6:1 2160 A303_216.6 S05 + M05B4 P63 + BN63B4 N56C 84...87
7.7 1867 4.0 217.4:1 3370 A413_217.4 S05 + M05B4 P63 + BN63B4 N56C 88...91

7.5 1900 1.2 221.3:1 1390 A203_221.3 S05 + M05B4 P63 + BN63B4 N56C 80...83
7.3 1964 1.7 150.7:1 2160 A303_150.7 S1 + M1SC6 P71 + BN71A6 N56C 84...87
6.4 2253 3.3 262.5:1 3370 A413_262.5 S05 + M05B4 P63 + BN63B4 N56C 88...91
6.2 2331 1.4 271.5:1 2160 A303_271.5 S05 + M05B4 P63 + BN63B4 N56C 84...87
6.0 2403 3.1 184.4:1 3370 A413_184.4 S1 + M1SC6 P71 + BN71A6 N56C 88...91

5.3 2701 1.3 314.6:1 2160 A303_314.6 S05 + M05B4 P63 + BN63B4 N56C 84...87
5.2 2783 2.7 324.2:1 3370 A413_324.2 S05 + M05B4 P63 + BN63B4 N56C 88...91
4.4 3235 2.3 376.8:1 3370 A413_376.8 S05 + M05B4 P63 + BN63B4 N56C 88...91
4.2 3421 2.2 262.5:1 3370 A413_262.5 S1 + M1SC6 P71 + BN71A6 N56C 88...91
4.1 3413 3.9 406.4:1 4500 A504_406.4 P63 + BN63B4 N56C 92...95

3.7 3752 3.5 446.8:1 4500 A504_446.8 P63 + BN63B4 N56C 92...95
3.4 4225 1.8 324.2:1 3370 A413_324.2 S1 + M1SC6 P71 + BN71A6 N56C 88...91
3.2 4446 3.0 529.5:1 4500 A504_529.5 P63 + BN63B4 N56C 92...95
2.9 4912 1.5 376.8:1 3370 A413_376.8 S1 + M1SC6 P71 + BN71A6 N56C 88...91
2.9 4822 2.8 574.3:1 4500 A504_574.3 P63 + BN63B4 N56C 92...95

2.7 5217 2.5 621.3:1 4500 A504_621.3 P63 + BN63B4 N56C 92...95
2.4 5944 2.2 707.9:1 4500 A504_707.9 P63 + BN63B4 N56C 92...95
2.2 6378 3.9 500.3:1 6740 A604_500.3 S1 + M1SC6 P71 + BN71A6 N56C 96...99
2.1 6535 2.0 778.2:1 4500 A504_778.2 P63 + BN63B4 N56C 92...95
1.9 7320 1.8 574.2:1 4500 A504_574.2 S1 + M1SC6 P71 + BN71A6 N56C 92...95

1.9 7468 3.3 585.8:1 6740 A604_585.8 S1 + M1SC6 P71 + BN71A6 N56C 96...99
1.6 8889 2.8 697.3:1 6740 A604_697.3 S1 + M1SC6 P71 + BN71A6 N56C 96...99
1.4 9921 1.3 778.2:1 4500 A504_778.2 S1 + M1SC6 P71 + BN71A6 N56C 92...95
1.2 11302 3.9 1346:1 11200 A704_1346 P63 + BN63B4 N56C 100...103
1.1 13293 3.3 1583:1 11200 A704_1583 P63 + BN63B4 N56C 100...103

0.97 14401 3.1 1715:1 11200 A704_1715 P63 + BN63B4 N56C 100...103
0.82 17159 2.6 1346:1 11200 A704_1346 S1 + M1SC6 P71 + BN71A6 N56C 100...103
0.64 21863 2.0 1715:1 11200 A704_1715 S1 + M1SC6 P71 + BN71A6 N56C 100...103

27
 0.33 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

306 64 19.4 5.5:1 680 A102_5.5 S05 + M05C4 P71 + BN71A4 N56C 76...79
232 84 14.7 7.2:1 740 A102_7.2 S05 + M05C4 P71 + BN71A4 N56C 76...79
174 113 11.0 9.6:1 810 A102_9.6 S05 + M05C4 P71 + BN71A4 N56C 76...79
158 124 10.7 10.6:1 830 A102_10.6 S05 + M05C4 P71 + BN71A4 N56C 76...79
153 128 9.7 7.2:1 840 A102_7.2 S1 + M1SD6 P71 + BN71B6 N56C 76...79

136 144 8.6 12.3:1 870 A102_12.3 S05 + M05C4 P71 + BN71A4 N56C 76...79
120 163 8.1 13.9:1 900 A102_13.9 S05 + M05C4 P71 + BN71A4 N56C 76...79
114 171 7.3 9.6:1 920 A102_9.6 S1 + M1SD6 P71 + BN71B6 N56C 76...79
104 188 7.1 10.6:1 950 A102_10.6 S1 + M1SD6 P71 + BN71B6 N56C 76...79
90 217 6.1 18.6:1 990 A102_18.6 S05 + M05C4 P71 + BN71A4 N56C 76...79

79 248 5.4 13.9:1 1030 A102_13.9 S1 + M1SD6 P71 + BN71B6 N56C 76...79
70 278 4.8 23.8:1 1060 A102_23.8 S05 + M05C4 P71 + BN71A4 N56C 76...79
58 334 4.0 28.6:1 1120 A102_28.6 S05 + M05C4 P71 + BN71A4 N56C 76...79
48 411 3.2 35.1:1 1180 A102_35.1 S05 + M05C4 P71 + BN71A4 N56C 76...79
46 422 3.1 23.8:1 1190 A102_23.8 S1 + M1SD6 P71 + BN71B6 N56C 76...79

37 531 2.5 45.4:1 1240 A102_45.4 S05 + M05C4 P71 + BN71A4 N56C 76...79
33 600 2.2 51.3:1 1240 A102_51.3 S05 + M05C4 P71 + BN71A4 N56C 76...79
31.1 628 3.5 53.7:1 1390 A202_53.7 S05 + M05C4 P71 + BN71A4 N56C 80...83
26.4 739 2.9 63.1:1 1390 A202_63.1 S05 + M05C4 P71 + BN71A4 N56C 80...83
25.3 772 1.7 65.9:1 1240 A102_65.9 S05 + M05C4 P71 + BN71A4 N56C 76...79

22.2 880 3.5 76.5:1 2160 A302_76.5 P71 + BN71A4 N56C 84...87
21.9 894 1.5 76.4:1 1240 A102_76.4 S05 + M05C4 P71 + BN71A4 N56C 76...79
20.9 935 2.0 79.9:1 1390 A202_79.9 S05 + M05C4 P71 + BN71A4 N56C 80...83
18.1 1081 1.6 92.3:1 1390 A202_92.3 S05 + M05C4 P71 + BN71A4 N56C 80...83
17.4 1121 2.4 97.5:1 2160 A302_97.5 P71 + BN71A4 N56C 84...87

13.9 1365 1.9 120.5:1 2160 A303_120.5 S05 + M05C4 P71 + BN71A4 N56C 84...87
13.9 1366 1.4 120.5:1 1390 A203_120.5 S05 + M05C4 P71 + BN71A4 N56C 80...83
11.4 1656 1.2 146.1:1 1390 A203_146.1 S05 + M05C4 P71 + BN71A4 N56C 80...83
11.4 1665 4.5 146.9:1 3370 A413_146.9 S05 + M05C4 P71 + BN71A4 N56C 88...91
11.3 1733 1.5 97.5:1 2160 A302_97.5 S05 + M1SD6 P71 + BN71B6 N56C 84...87

11.1 1707 1.7 150.7:1 2160 A303_150.7 S05 + M05C4 P71 + BN71A4 N56C 84...87
9.4 2023 1.5 178.5:1 2160 A303_178.5 S05 + M05C4 P71 + BN71A4 N56C 84...87
9.1 2089 3.6 184.4:1 3370 A413_184.4 S05 + M05C4 P71 + BN71A4 N56C 88...91
7.7 2454 1.3 216.6:1 2160 A303_216.6 S05 + M05C4 P71 + BN71A4 N56C 84...87
7.7 2464 3.1 217.4:1 3370 A413_217.4 S05 + M05C4 P71 + BN71A4 N56C 88...91

6.4 2974 2.5 262.5:1 3370 A413_262.5 S05 + M05C4 P71 + BN71A4 N56C 88...91
5.9 3123 4.3 286.8:1 4500 A504_286.8 P71 + BN71A4 N56C 92...95
5.2 3674 2.0 324.2:1 3370 A413_324.2 S05 + M05C4 P71 + BN71A4 N56C 88...91
5.1 3622 3.7 332.6:1 4500 A504_332.6 P71 + BN71A4 N56C 92...95
4.6 3981 3.3 365.6:1 4500 A504_365.6 P71 + BN71A4 N56C 92...95

4.4 4271 1.8 376.8:1 3370 A413_376.8 S05 + M05C4 P71 + BN71A4 N56C 88...91
4.2 4516 1.7 262.5:1 3370 A413_262.5 S1 + M1SD6 P71 + BN71B6 N56C 88...91
4.2 4425 3.0 406.4:1 4500 A504_406.4 P71 + BN71A4 N56C 92...95

28
 0.33 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

3.8 4865 2.7 446.8:1 4500 A504_446.8 P71 + BN71A4 N56C 92...95
3.6 5175 2.6 481.6:1 4500 A504_481.6 P71 + BN71A4 N56C 92...95
3.2 5765 2.3 529.5:1 4500 A504_529.5 P71 + BN71A4 N56C 92...95
3.1 5902 4.2 542.0:1 4500 A604_542.0 P71 + BN71A4 N56C 96...99
2.7 6765 2.0 621.3:1 4500 A504_621.3 P71 + BN71A4 N56C 92...95

2.7 6910 3.6 634.6:1 6740 A604_634.6 P71 + BN71A4 N56C 96...99
2.4 7593 3.3 697.3:1 6740 A604_697.3 P71 + BN71A4 N56C 96...99
2.4 7708 1.7 707.9:1 4500 A504_707.9 P71 + BN71A4 N56C 92...95
2.2 8419 2.9 500.3:1 6740 A604_500.3 S1 + M1SD6 P71 + BN71B6 N56C 96...99
2.2 8473 1.6 778.2:1 4500 A504_778.2 P71 + BN71A4 N56C 92...95

1.9 9858 2.5 585.8:1 6740 A604_585.8 S1 + M1SD6 P71 + BN71B6 N56C 96...99
1.8 10088 4.4 926.5:1 11200 A704_926.5 P71 + BN71A4 N56C 100...103
1.5 12652 3.5 1162:1 11200 A704_1162 P71 + BN71A4 N56C 100...103
1.5 12712 1.9 755.4:1 6740 A604_755.4 S1 + M1SD6 P71 + BN71B6 N56C 96...99
1.3 14656 3.0 1346:1 11200 A704_1346 P71 + BN71A4 N56C 100...103

0.99 18674 2.4 1715:1 11200 A704_1715 P71 + BN71A4 N56C 100...103
0.82 22650 2.0 1346:1 11200 A704_1346 S1 + M1SD6 P71 + BN71B6 N56C 100...103
0.64 28859 1.5 1715:1 11200 A704_1715 S1 + M1SD6 P71 + BN71B6 N56C 100...103

0.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

311 95 13.0 5.5:1 670 A102_5.5 S1 + M1SD4 P71 + BN71B4 N56C 76...79
236 126 9.9 7.2:1 730 A102_7.2 S1 + M1SD4 P71 + BN71B4 N56C 76...79
201 147 8.4 5.5:1 760 A102_5.5 S1 + M1LA6 P80 + BN80A6 N56C 76...79
177 168 7.4 9.6:1 790 A102_9.6 S1 + M1SD4 P71 + BN71B4 N56C 76...79
161 184 7.2 10.6:1 820 A102_10.6 S1 + M1SD4 P71 + BN71B4 N56C 76...79

138 214 5.8 12.3:1 850 A102_12.3 S1 + M1SD4 P71 + BN71B4 N56C 76...79
122 243 5.5 13.9:1 890 A102_13.9 S1 + M1SD4 P71 + BN71B4 N56C 76...79
114 259 4.8 9.6:1 890 A102_9.6 S1 + M1LA6 P80 + BN80A6 N56C 76...79
104 284 4.7 10.6:1 920 A102_10.6 S1 + M1LA6 P80 + BN80A6 N56C 76...79
92 324 4.1 18.6:1 960 A102_18.6 S1 + M1SD4 P71 + BN71B4 N56C 76...79

79 375 3.5 13.9:1 990 A102_13.9 S1 + M1LA6 P80 + BN80A6 N56C 76...79
72 414 3.2 23.8:1 1030 A102_23.8 S1 + M1SD4 P71 + BN71B4 N56C 76...79
59 498 2.7 28.6:1 1080 A102_28.6 S1 + M1SD4 P71 + BN71B4 N56C 76...79
58 509 4.3 29.2:1 1170 A202_29.2 S1 + M1SD4 P71 + BN71B4 N56C 80...83
48 612 2.2 35.1:1 1130 A102_35.1 S1 + M1SD4 P71 + BN71B4 N56C 76...79

48 617 3.6 35.4:1 1230 A202_35.4 S1 + M1SD4 P71 + BN71B4 N56C 80...83
39 753 2.9 43.2:1 1300 A202_43.2 S1 + M1SD4 P71 + BN71B4 N56C 80...83

29
 0.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

37 791 1.7 45.4:1 1200 A102_45.4 S1 + M1SD4 P71 + BN71B4 N56C 76...79
33 893 1.5 51.3:1 1230 A102_51.3 S1 + M1SD4 P71 + BN71B4 N56C 76...79
32 918 4.0 52.7:1 1980 A302_52.7 S1 + M1SD4 P71 + BN71B4 N56C 84...87
32 935 2.4 53.7:1 1370 A202_53.7 S1 + M1SD4 P71 + BN71B4 N56C 80...83
26.9 1100 2.0 63.1:1 1390 A202_63.1 S1 + M1SD4 P71 + BN71B4 N56C 80...83

25.8 1149 1.2 65.9:1 1240 A102_65.9 S1 + M1SD4 P71 + BN71B4 N56C 76...79
25.7 1151 3.0 66.0:1 2100 A302_66.0 S1 + M1SD4 P71 + BN71B4 N56C 84...87
22.2 1333 2.3 76.5:1 2160 A302_76.5 S1 + M1SD4 P71 + BN71B4 N56C 84...87
21.3 1391 1.3 79.9:1 1390 A202_79.9 S1 + M1SD4 P71 + BN71B4 N56C 80...83
18.3 1565 4.5 92.8:1 3370 A413_92.8 S1 + M1SD4 P71 + BN71B4 N56C 88...91

17.4 1699 1.6 97.5:1 2160 A302_97.5 S1 + M1SD4 P71 + BN71B4 N56C 84...87
14.7 1954 3.8 115.9:1 3370 A413_115.9 S1 + M1SD4 P71 + BN71B4 N56C 88...91
14.1 2032 1.3 120.5:1 2160 A303_120.5 S1 + M1SD4 P71 + BN71B4 N56C 84...87
13.9 2134 3.3 79.2:1 3370 A412_79.2 S1 + M1LA6 P80 + BN80A6 N56C 88...91
11.9 2418 2.9 92.8:1 3370 A413_92.8 S1 + M1LA6 P80 + BN80A6 N56C 88...91

11.6 2478 3.0 146.9:1 3370 A413_146.9 S1 + M1SD4 P71 + BN71B4 N56C 88...91
11.3 2541 1.1 150.7:1 2160 A303_150.7 S1 + M1SD4 P71 + BN71B4 N56C 84...87
9.2 3110 2.4 184.4:1 3370 A413_184.4 S1 + M1SD4 P71 + BN71B4 N56C 88...91
8.1 3481 3.8 211.0:1 4500 A504_211.0 S1 + M1SD4 P71 + BN71B4 N56C 92...95
7.8 3667 2.1 217.4:1 3370 A413_217.4 S1 + M1SD4 P71 + BN71B4 N56C 88...91

7.5 3829 2.0 146.9:1 3370 A413_146.9 S1 + M1LA6 P80 + BN80A6 N56C 88...91
6.5 4427 1.7 262.5:1 3370 A413_262.5 S1 + M1SD4 P71 + BN71B4 N56C 88...91
6.0 4806 1.6 184.4:1 3370 A413_184.4 S1 + M1LA6 P80 + BN80A6 N56C 88...91
5.9 4732 2.8 286.8:1 4500 A504_286.8 S1 + M1SD4 P71 + BN71B4 N56C 92...95
5.2 5468 1.4 324.2:1 3370 A413_324.2 S1 + M1SD4 P71 + BN71B4 N56C 88...91

5.1 5487 2.4 332.6:1 4500 A504_332.6 S1 + M1SD4 P71 + BN71B4 N56C 92...95
4.6 6032 2.2 365.6:1 4500 A504_365.6 S1 + M1SD4 P71 + BN71B4 N56C 92...95
4.5 6357 1.2 376.8:1 3370 A413_376.8 S1 + M1SD4 P71 + BN71B4 N56C 88...91
4.2 6677 3.7 404.7:1 6740 A604_404.7 S1 + M1SD4 P71 + BN71B4 N56C 96...99
4.2 6705 2.0 406.4:1 4500 A504_406.4 S1 + M1SD4 P71 + BN71B4 N56C 92...95

3.8 7371 1.8 446.8:1 4500 A504_446.8 S1 + M1SD4 P71 + BN71B4 N56C 92...95
3.5 7945 1.7 481.6:1 4500 A504_481.6 S1 + M1SD4 P71 + BN71B4 N56C 92...95
3.2 8736 1.5 529.5:1 4500 A504_529.5 S1 + M1SD4 P71 + BN71B4 N56C 92...95
3.1 8942 2.8 542.0:1 6740 A604_542.0 S1 + M1SD4 P71 + BN71B4 N56C 96...99
2.7 10413 1.3 631.2:1 4500 A504_631.2 S1 + M1SD4 P71 + BN71B4 N56C 92...95

2.7 10469 2.4 634.6:1 6740 A604_634.6 S1 + M1SD4 P71 + BN71B4 N56C 96...99
2.6 10634 4.2 644.6:1 11200 A704_644.6 S1 + M1SD4 P71 + BN71B4 N56C 100...103
2.4 11679 1.1 707.9:1 4500 A504_707.9 S1 + M1SD4 P71 + BN71B4 N56C 92...95
2.3 12462 2.0 755.4:1 6740 A604_755.4 S1 + M1SD4 P71 + BN71B4 N56C 96...99
2.2 12603 3.5 763.9:1 11200 A704_763.9 S1 + M1SD4 P71 + BN71B4 N56C 100...103

1.8 15285 2.9 926.5:1 11200 A704_926.5 S1 + M1SD4 P71 + BN71B4 N56C 100...103
1.7 16180 1.5 634.6:1 6740 A604_634.6 S1 + M1LA6 P80 + BN80A6 N56C 96...99
1.6 17900 4.0 1085:1 14600 A804_1085 S1 + M1SD4 P71 + BN71B4 N56C 104...107

30
 0.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

1.5 19170 2.3 1162:1 11200 A704_1162 S1 + M1SD4 P71 + BN71B4 N56C 100...103
1.3 22107 3.2 1340:1 14600 A804_1340 S1 + M1SD4 P71 + BN71B4 N56C 104...107
1.3 22206 2.0 1346:1 11200 A704_1346 S1 + M1SD4 P71 + BN71B4 N56C 100...103
1.0 27664 2.6 1085:1 14600 A804_1085 S1 + M1LA6 P80 + BN80A6 N56C 104...107
0.99 28294 1.6 1715:1 11200 A704_1715 S1 + M1SD4 P71 + BN71B4 N56C 100...103

0.70 40150 3.1 1632:1 16900 A904_1632 P80 + BN80A6 N56C 108...111
0.69 40361 1.1 1583:1 11200 A704_1583 S1 + M1LA6 P80 + BN80A6 N56C 100...103

0.75 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

313 142 8.7 5.5:1 660 A102_5.5 S1 + M1LA4 P80 + BN80A4 N56C 76...79
237 187 6.6 7.2:1 710 A102_7.2 S1 + M1LA4 P80 + BN80A4 N56C 76...79
209 213 5.8 5.5:1 740 A102_5.5 S2 + M2SA6 P80 + BN80B6 N140TC 76...79
178 250 5.0 9.6:1 770 A102_9.6 S1 + M1LA4 P80 + BN80A4 N56C 76...79
162 274 4.8 10.6:1 790 A102_10.6 S1 + M1LA4 P80 + BN80A4 N56C 76...79

158 281 4.4 7.2:1 800 A102_7.2 S2 + M2SA6 P80 + BN80B6 N140TC 76...79
139 320 3.9 12.3:1 830 A102_12.3 S1 + M1LA4 P80 + BN80A4 N56C 76...79
123 362 3.7 13.9:1 850 A102_13.9 S1 + M1LA4 P80 + BN80A4 N56C 76...79
119 375 3.3 9.6:1 860 A102_9.6 S2 + M2SA6 P80 + BN80B6 N140TC 76...79
108 411 3.2 10.6:1 880 A102_10.6 S2 + M2SA6 P80 + BN80B6 N140TC 76...79

92 483 2.8 18.6:1 920 A102_18.6 S1 + M1LA4 P80 + BN80A4 N56C 76...79
82 543 2.4 13.9:1 940 A102_13.9 S2 + M2SA6 P80 + BN80B6 N140TC 76...79
74 601 3.7 23.1:1 1050 A202_23.1 S1 + M1LA4 P80 + BN80A4 N56C 80...83
72 618 2.1 23.8:1 970 A102_23.8 S1 + M1LA4 P80 + BN80A4 N56C 76...79
60 742 1.8 28.6:1 1010 A102_28.6 S1 + M1LA4 P80 + BN80A4 N56C 76...79

59 759 2.9 29.2:1 1120 A202_29.2 S1 + M1LA4 P80 + BN80A4 N56C 80...83
49 912 1.5 35.1:1 1060 A102_35.1 S1 + M1LA4 P80 + BN80A4 N56C 76...79
48 921 2.4 35.4:1 1170 A202_35.4 S1 + M1LA4 P80 + BN80A4 N56C 80...83
47 952 3.8 36.6:1 1720 A302_36.6 S1 + M1LA4 P80 + BN80A4 N56C 84...87
40 1123 2.0 43.2:1 1220 A202_43.2 S1 + M1LA4 P80 + BN80A4 N56C 80...83

39 1128 3.2 43.4:1 1800 A302_43.4 S1 + M1LA4 P80 + BN80A4 N56C 84...87
38 1180 1.1 45.4:1 1100 A102_45.4 S1 + M1LA4 P80 + BN80A4 N56C 76...79
32 1369 2.7 52.7:1 1890 A302_52.7 S1 + M1LA4 P80 + BN80A4 N56C 84...87
32 1394 1.6 53.7:1 1270 A202_53.7 S1 + M1LA4 P80 + BN80A4 N56C 80...83
27.1 1641 1.3 63.1:1 1310 A202_63.1 S1 + M1LA4 P80 + BN80A4 N56C 80...83

26.7 1667 4.5 64.2:1 3370 A412_64.2 S1 + M1LA4 P80 + BN80A4 N56C 88...91
25.9 1716 2.0 66.0:1 2000 A302_66.0 S1 + M1LA4 P80 + BN80A4 N56C 84...87
25.3 1757 4.3 45.1:1 3370 A412_45.1 S2 + M2SA6 P80 + BN80B6 N140TC 88...91

31
 0.75 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

22.3 1988 1.6 76.5:1 2060 A302_76.5 S1 + M1LA4 P80 + BN80A4 N56C 84...87
21.6 2059 3.7 79.2:1 3370 A412_79.2 S1 + M1LA4 P80 + BN80A4 N56C 88...91
21.5 2071 3.6 53.1:1 3370 A412_53.1 S2 + M2SA6 P80 + BN80B6 N140TC 88...91
18.4 2334 3.0 92.8:1 3370 A413_92.8 S1 + M1LA4 P80 + BN80A4 N56C 88...91
14.8 2914 2.6 115.9:1 3370 A413_115.9 S1 + M1LA4 P80 + BN80A4 N56C 88...91

14.4 3088 2.3 79.2:1 3370 A412_79.2 S2 + M2SA6 P80 + BN80B6 N140TC 88...91
12.3 3500 2.0 92.8:1 3370 A413_92.8 S2 + M2SA6 P80 + BN80B6 N140TC 88...91
11.6 3695 2.0 146.9:1 3370 A413_146.9 S1 + M1LA4 P80 + BN80A4 N56C 88...91
9.9 4361 3.0 173.4:1 4500 A503_173.4 S1 + M1LA4 P80 + BN80A4 N56C 92...95
9.8 4372 1.7 115.9:1 3370 A413_115.9 S2 + M2SA6 P80 + BN80B6 N140TC 88...91

9.3 4638 1.6 184.4:1 3370 A413_184.4 S1 + M1LA4 P80 + BN80A4 N56C 88...91
9.0 4794 2.8 190.6:1 4500 A503_190.6 S1 + M1LA4 P80 + BN80A4 N56C 92...95
8.1 5191 2.6 211.0:1 4500 A504_211.0 S1 + M1LA4 P80 + BN80A4 N56C 92...95
7.9 5469 1.4 217.4:1 3370 A413_217.4 S1 + M1LA4 P80 + BN80A4 N56C 88...91
7.4 5708 2.3 232.0:1 4500 A504_232.0 S1 + M1LA4 P80 + BN80A4 N56C 92...95

6.6 6419 2.1 260.9:1 4500 A504_260.9 S1 + M1LA4 P80 + BN80A4 N56C 92...95
6.5 6602 1.1 262.5:1 3370 A413_262.5 S1 + M1LA4 P80 + BN80A4 N56C 88...91
6.5 6502 3.8 264.3:1 6740 A604_264.3 S1 + M1LA4 P80 + BN80A4 N56C 96...99
6.0 7044 3.5 286.3:1 6740 A604_286.3 S1 + M1LA4 P80 + BN80A4 N56C 96...99
6.0 7056 1.9 286.8:1 4500 A504_286.8 S1 + M1LA4 P80 + BN80A4 N56C 92...95

5.3 7976 3.1 324.2:1 6740 A604_324.2 S1 + M1LA4 P80 + BN80A4 N56C 96...99
5.1 8183 1.6 332.6:1 4500 A504_332.6 S1 + M1LA4 P80 + BN80A4 N56C 92...95
4.9 8640 2.9 351.2:1 6740 A604_351.2 S1 + M1LA4 P80 + BN80A4 N56C 96...99
4.7 8994 1.5 365.6:1 4500 A504_365.6 S1 + M1LA4 P80 + BN80A4 N56C 92...95
4.2 9956 2.5 404.7:1 6740 A604_404.7 S1 + M1LA4 P80 + BN80A4 N56C 96...99

4.2 9998 1.3 406.4:1 4500 A504_406.4 S1 + M1LA4 P80 + BN80A4 N56C 92...95
3.9 10785 2.3 438.4:1 6740 A604_438.4 S1 + M1LA4 P80 + BN80A4 N56C 96...99
3.8 10992 1.2 446.8:1 4500 A504_446.8 S1 + M1LA4 P80 + BN80A4 N56C 92...95
3.6 11848 1.1 481.6:1 4500 A504_481.6 S1 + M1LA4 P80 + BN80A4 N56C 92...95
3.4 12308 2.0 500.3:1 6740 A604_500.3 S1 + M1LA4 P80 + BN80A4 N56C 96...99

3.3 12680 3.5 515.4:1 11200 A704_515.4 S1 + M1LA4 P80 + BN80A4 N56C 100...103
2.9 14412 1.7 585.8:1 6740 A604_585.8 S1 + M1LA4 P80 + BN80A4 N56C 96...99
2.9 14638 3.0 595.0:1 11200 A704_595.0 S1 + M1LA4 P80 + BN80A4 N56C 100...103
2.5 17155 1.4 697.3:1 6740 A604_697.3 S1 + M1LA4 P80 + BN80A4 N56C 96...99
2.4 17307 4.1 703.5:1 14600 A804_703.5 S1 + M1LA4 P80 + BN80A4 N56C 104...107

2.4 17347 2.6 705.1:1 11200 A704_705.1 S1 + M1LA4 P80 + BN80A4 N56C 100...103
2.1 20407 3.5 829.5:1 14600 A804_829.5 S1 + M1LA4 P80 + BN80A4 N56C 104...107
2.0 21042 2.1 855.3:1 11200 A704_855.3 S1 + M1LA4 P80 + BN80A4 N56C 100...103
1.7 24626 2.9 1001:1 14600 A804_1001 S1 + M1LA4 P80 + BN80A4 N56C 104...107
1.6 26373 1.7 1072:1 11200 A704_1072 S1 + M1LA4 P80 + BN80A4 N56C 100...103

1.4 30433 2.3 1237:1 14600 A804_1237 S1 + M1LA4 P80 + BN80A4 N56C 104...107
1.4 30556 1.4 1242:1 11200 A704_1242 S1 + M1LA4 P80 + BN80A4 N56C 100...103
1.1 38330 1.8 1558:1 14600 A804_1558 S1 + M1LA4 P80 + BN80A4 N56C 104...107

32
 0.75 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

1.1 38945 1.1 1583:1 11200 A704_1583 S1 + M1LA4 P80 + BN80A4 N56C 100...103
1.0 40150 3.1 1632:1 16900 A904_1632 S1 + M1LA4 P80 + BN80A4 N56C 108...111
0.73 57495 1.2 1558:1 14600 A804_1558 S2 + M2SA6 P80 + BN80B6 N140TC 104...107
0.70 60225 2.1 1632:1 16900 A904_1632 S2 + M2SA6 P80 + BN80B6 N140TC 108...111

1 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

315 188 6.6 5.5:1 640 A102_5.5 S2 + M2SA4 P80 + BN80B4 N56C 76...79
239 248 5.0 7.2:1 690 A102_7.2 S2 + M2SA4 P80 + BN80B4 N56C 76...79
209 284 4.4 5.5:1 720 A102_5.5 S2 + M2SB6 P90 + BN90S6 N140TC 76...79
179 331 3.7 9.6:1 750 A102_9.6 S2 + M2SA4 P80 + BN80B4 N56C 76...79
163 364 3.7 10.6:1 760 A102_10.6 S2 + M2SA4 P80 + BN80B4 N56C 76...79

158 375 3.3 7.2:1 770 A102_7.2 S2 + M2SB6 P90 + BN90S6 N140TC 76...79
140 424 2.9 12.3:1 790 A102_12.3 S2 + M2SA4 P80 + BN80B4 N56C 76...79
123 480 2.8 13.9:1 820 A102_13.9 S2 + M2SA4 P80 + BN80B4 N56C 76...79
122 487 3.8 9.4:1 890 A202_9.4 S2 + M2SB6 P90 + BN90S6 N140TC 80...83
119 500 2.5 9.6:1 830 A102_9.6 S2 + M2SB6 P90 + BN90S6 N140TC 76...79

110 537 4.1 10.3:1 920 A202_10.3 S2 + M2SB6 P90 + BN90S6 N140TC 80...83
108 549 2.4 10.6:1 850 A102_10.6 S2 + M2SB6 P90 + BN90S6 N140TC 76...79
95 624 3.5 18.1:1 950 A202_18.1 S2 + M2SA4 P80 + BN80B4 N56C 80...83
93 640 2.1 18.6:1 870 A102_18.6 S2 + M2SA4 P80 + BN80B4 N56C 76...79
82 724 1.8 13.9:1 890 A102_13.9 S2 + M2SB6 P90 + BN90S6 N140TC 76...79

74 796 2.8 23.1:1 1010 A202_23.1 S2 + M2SA4 P80 + BN80B4 N56C 80...83
72 819 1.6 23.8:1 910 A102_23.8 S2 + M2SA4 P80 + BN80B4 N56C 76...79
60 984 1.3 28.6:1 940 A102_28.6 S2 + M2SA4 P80 + BN80B4 N56C 76...79
59 1006 2.2 29.2:1 1060 A202_29.2 S2 + M2SA4 P80 + BN80B4 N56C 80...83
59 1009 3.6 29.3:1 1560 A302_29.3 S2 + M2SA4 P80 + BN80B4 N56C 84...87

49 1220 1.8 35.4:1 1100 A202_35.4 S2 + M2SA4 P80 + BN80B4 N56C 80...83
40 1489 1.5 43.2:1 1140 A202_43.2 S2 + M2SA4 P80 + BN80B4 N56C 80...83
40 1496 2.4 43.4:1 1720 A302_43.4 S2 + M2SA4 P80 + BN80B4 N56C 84...87
38 1552 4.7 45.1:1 3370 A412_45.1 S2 + M2SA4 P80 + BN80B4 N56C 88...91
32 1841 1.2 35.4:1 1170 A202_35.4 S2 + M2SB6 P90 + BN90S6 N140TC 80...83

32 1866 4.0 35.9:1 3370 A412_35.9 S2 + M2SB6 P90 + BN90S6 N140TC 88...91
31 1905 1.9 36.6:1 1820 A302_36.6 S2 + M2SB6 P90 + BN90S6 N140TC 84...87
26.8 2210 3.4 64.2:1 3370 A412_64.2 S2 + M2SA4 P80 + BN80B4 N56C 88...91
26.0 2274 1.5 66.0:1 1880 A302_66.0 S2 + M2SA4 P80 + BN80B4 N56C 84...87
25.3 2342 3.2 45.1:1 3370 A412_45.1 S2 + M2SB6 P90 + BN90S6 N140TC 88...91

22.5 2635 1.2 76.5:1 1930 A302_76.5 S2 + M2SA4 P80 + BN80B4 N56C 84...87

33
 1 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

21.7 2729 2.8 79.2:1 3370 A412_79.2 S2 + M2SA4 P80 + BN80B4 N56C 88...91
18.5 3093 2.3 92.8:1 3370 A413_92.8 S2 + M2SA4 P80 + BN80B4 N56C 88...91
17.8 3334 2.3 64.2:1 3370 A412_64.2 S2 + M2SB6 P90 + BN90S6 N140TC 88...91
17.3 3319 4.0 99.5:1 4500 A503_99.5 S2 + M2SA4 P80 + BN80B4 N56C 92...95
15.7 3649 3.6 109.4:1 4500 A503_109.4 S2 + M2SA4 P80 + BN80B4 N56C 92...95

14.8 3863 1.9 115.9:1 3370 A413_115.9 S2 + M2SA4 P80 + BN80B4 N56C 88...91
14.6 3933 3.4 118.0:1 4500 A503_118.0 S2 + M2SA4 P80 + BN80B4 N56C 92...95
14.4 4118 1.7 79.2:1 3370 A412_79.2 S2 + M2SB6 P90 + BN90S6 N140TC 88...91
12.2 4689 2.8 140.6:1 4500 A503_140.6 S2 + M2SA4 P80 + BN80B4 N56C 92...95
11.7 4898 1.5 146.9:1 3370 A413_146.9 S2 + M2SA4 P80 + BN80B4 N56C 88...91

11.1 5155 2.6 154.6:1 4500 A503_154.6 S2 + M2SA4 P80 + BN80B4 N56C 92...95
10.0 5717 4.3 171.5:1 6740 A603_171.5 S2 + M2SA4 P80 + BN80B4 96...99
9.9 5781 2.3 173.4:1 4500 A503_173.4 S2 + M2SA4 P80 + BN80B4 N56C 92...95
9.3 6148 1.2 184.4:1 3370 A413_184.4 S2 + M2SA4 P80 + BN80B4 N56C 88...91
8.2 6806 3.6 208.7:1 6740 A604_208.7 S2 + M2SA4 P80 + BN80B4 N56C 96...99

8.2 6881 1.9 211.0:1 4500 A504_211.0 S2 + M2SA4 P80 + BN80B4 N56C 92...95
7.4 7566 1.8 232.0:1 4500 A504_232.0 S2 + M2SA4 P80 + BN80B4 N56C 92...95
6.6 8508 1.6 260.9:1 4500 A504_260.9 S2 + M2SA4 P80 + BN80B4 N56C 92...95
6.5 8619 2.9 264.3:1 6740 A604_264.3 S2 + M2SA4 P80 + BN80B4 N56C 96...99
6.0 9337 2.7 286.3:1 6740 A604_286.3 S2 + M2SA4 P80 + BN80B4 N56C 96...99

6.0 9353 1.4 286.8:1 4500 A504_286.8 S2 + M2SA4 P80 + BN80B4 N56C 92...95
5.4 10318 4.3 316.4:1 11200 A704_316.4 S2 + M2SA4 P80 + BN80B4 N56C 100...103
5.3 10576 2.3 324.2:1 6740 A604_324.2 S2 + M2SA4 P80 + BN80B4 N56C 96...99
5.2 10847 1.2 332.6:1 4500 A504_332.6 S2 + M2SA4 P80 + BN80B4 N56C 92...95
4.9 11453 2.2 351.2:1 6740 A604_351.2 S2 + M2SA4 P80 + BN80B4 N56C 96...99

4.7 11923 1.1 365.6:1 4500 A504_365.6 S2 + M2SA4 P80 + BN80B4 N56C 92...95
4.3 13051 3.4 400.2:1 11200 A704_400.2 S2 + M3SA4 P80 + BN80B4 N56C 100...103
4.3 13198 1.9 404.7:1 6740 A604_404.7 S2 + M2SA4 P80 + BN80B4 N56C 96...99
3.9 14297 1.7 438.4:1 6740 A604_438.4 S2 + M2SA4 P80 + BN80B4 N56C 96...99
3.6 15517 2.9 475.8:1 11200 A704_475.8 S2 + M2SA4 P80 + BN80B4 N56C 100...103

3.3 16808 2.6 515.4:1 11200 A704_515.4 S2 + M2SA4 P80 + BN80B4 N56C 100...103
3.2 17676 1.4 542.0:1 6740 A604_542.0 S2 + M2SA4 P80 + BN80B4 N56C 96...99
3.0 18426 2.4 565.0:1 11200 A704_565.0 S2 + M2SA4 P80 + BN80B4 N56C 100...103
2.9 19104 1.3 585.8:1 6740 A604_585.8 S2 + M2SA4 P80 + BN80B4 N56C 96...99
2.7 20676 1.2 634.6:1 6740 A604_634.6 S2 + M2SA4 P80 + BN80B4 N56C 96...99

2.7 21022 2.1 644.6:1 11200 A704_644.6 S2 + M2SA4 P80 + BN80B4 N56C 100...103
2.4 22942 3.1 703.5:1 14600 A804_703.5 S2 + M2SA4 P80 + BN80B4 N56C 104...107
2.4 22995 1.9 705.1:1 11200 A704_705.1 S2 + M2SA4 P80 + BN80B4 N56C 100...103
2.1 27051 2.6 829.5:1 14600 A804_829.5 S2 + M2SA4 P80 + BN80B4 N56C 104...107
2.0 27893 1.6 855.3:1 11200 A704_855.3 S2 + M3SA4 P80 + BN80B4 N56C 100...103

1.7 32644 2.2 1001:1 14600 A804_1001 S2 + M2SA4 P80 + BN80B4 N56C 104...107
1.7 33427 3.7 1025:1 16900 A904_1025 S2 + M2SA4 P80 + BN80B4 N56C 108...111
1.6 34960 1.3 1072:1 11200 A704_1072 S2 + M2SA4 P80 + BN80B4 N56C 100...103

34
 1 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

1.5 37895 1.2 1162:1 11200 A704_1162 S2 + M2SA4 P80 + BN80B4 N56C 100...103
1.4 39852 3.1 1222:1 16900 A904_1222 S2 + M2SA4 P80 + BN80B4 N56C 108...111
1.4 40341 1.8 1237:1 14600 A804_1237 S2 + M2SA4 P80 + BN80B4 N56C 104...107
1.1 49146 2.5 1507:1 16900 A904_1507 S2 + M2SA4 P80 + BN80B4 N56C 108...111
1.1 50809 1.4 1558:1 14600 A804_1558 S2 + M2SA4 P80 + BN80B4 N56C 104...107

0.92 60865 1.2 1237:1 14600 A804_1237 S2 + M2SB6 P90 + BN90S6 N140TC 104...107
0.70 80300 1.5 1632:1 16900 A904_1632 S2 + M2SB6 P90 + BN90S6 N140TC 108...111

1.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

315 282 4.4 5.5:1 620 A102_5.5 S2 + M2SB4 P90 + BN90S4 N140TC 76...79
239 373 3.3 7.2:1 660 A102_7.2 S2 + M2SB4 P90 + BN90S4 N140TC 76...79
209 426 2.9 5.5:1 680 A102_5.5 S3 + M3SA6 P90 + BN90L6 N180TC 76...79
183 484 3.8 9.4:1 770 A202_9.4 S2 + M2SB4 P90 + BN90S4 N140TC 80...83
179 497 2.5 9.6:1 710 A102_9.6 S2 + M2SB4 P90 + BN90S4 N140TC 76...79

166 534 3.7 10.3:1 790 A202_10.3 S2 + M2SB4 P90 + BN90S4 N140TC 80...83
163 545 2.4 10.6:1 720 A102_10.6 S2 + M2SB4 P90 + BN90S4 N140TC 76...79
140 636 1.9 12.3:1 740 A102_12.3 S2 + M2SB4 P90 + BN90S4 N140TC 76...79
123 720 1.8 13.9:1 760 A102_13.9 S2 + M2SB4 P90 + BN90S4 N140TC 76...79
122 727 3.0 14.1:1 850 A202_14.1 S2 + M2SB4 P90 + BN90S4 N140TC 80...83

110 806 2.7 10.3:1 870 A202_10.3 S3 + M3SA6 P90 + BN90L6 N180TC 80...83
108 823 1.6 10.6:1 780 A102_10.6 S3 + M3SA6 P90 + BN90L6 N180TC 76...79
96 929 3.8 18.0:1 1320 A302_18.0 S2 + M2SB4 P90 + BN90S4 N140TC 84...87
95 936 2.4 18.1:1 890 A202_18.1 S2 + M2SB4 P90 + BN90S4 N140TC 80...83
93 960 1.4 18.6:1 800 A102_18.6 S2 + M2SB4 P90 + BN90S4 N140TC 76...79

82 1086 1.2 13.9:1 810 A102_13.9 S3 + M3SA6 P90 + BN90L6 N180TC 76...79
81 1097 2.0 14.1:1 920 A202_14.1 S3 + M3SA6 P90 + BN90L6 N180TC 80...83
76 1175 3.1 22.8:1 1400 A302_22.8 S2 + M2SB4 P90 + BN90S4 N140TC 84...87
74 1194 1.9 23.1:1 930 A202_23.1 S2 + M2SB4 P90 + BN90S4 N140TC 80...83
61 1463 4.4 28.3:1 3010 A412_28.3 S2 + M2SB4 P90 + BN90S4 N140TC 88...91

59 1510 1.5 29.2:1 960 A202_29.2 S2 + M2SB4 P90 + BN90S4 N140TC 80...83
59 1514 2.4 29.3:1 1480 A302_29.3 S2 + M2SB4 P90 + BN90S4 N140TC 84...87
49 1830 1.2 35.4:1 980 A202_35.4 S2 + M2SB4 P90 + BN90S4 N140TC 80...83
48 1855 3.7 35.9:1 3210 A412_35.9 S2 + M2SB4 P90 + BN90S4 N140TC 88...91
47 1893 1.9 36.6:1 1550 A302_36.6 S2 + M2SB4 P90 + BN90S4 N140TC 84...87

40 2244 1.6 43.4:1 1600 A302_43.4 S2 + M2SB4 P90 + BN90S4 N140TC 84...87
38 2328 3.2 45.1:1 3370 A412_45.1 S2 + M2SB4 P90 + BN90S4 N140TC 88...91
33 2722 1.3 52.7:1 1640 A302_52.7 S2 + M2SB4 P90 + BN90S4 N140TC 84...87

35
 1.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

32 2746 2.7 53.1:1 3370 A412_53.1 S2 + M2SB4 P90 + BN90S4 N140TC 88...91
26.8 3315 2.3 64.2:1 3370 A412_64.2 S2 + M2SB4 P90 + BN90S4 N140TC 88...91
25.3 3513 2.1 45.1:1 3370 A412_45.1 S3 + M3SA6 P90 + BN90L6 N180TC 88...91
24.5 3513 3.8 70.2:1 4500 A503_70.2 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
21.7 4094 1.8 79.2:1 3370 A412_79.2 S2 + M2SB4 P90 + BN90S4 N140TC 88...91

21.1 4074 3.3 81.5:1 4500 A503_81.5 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
18.5 4640 1.5 92.8:1 3370 A413_92.8 S2 + M2SB4 P90 + BN90S4 N140TC 88...91
17.8 5001 1.5 64.2:1 3370 A412_64.2 S3 + M3SA6 P90 + BN90L6 N180TC 88...91
17.3 4978 2.7 99.5:1 4500 A503_99.5 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
15.7 5473 2.4 109.4:1 4500 A503_109.4 S2 + M2SB4 P90 + BN90S4 N140TC 92...95

14.8 5795 1.3 115.9:1 3370 A413_115.9 S2 + M2SB4 P90 + BN90S4 N140TC 88...91
14.6 5900 2.3 118.0:1 4500 A503_118.0 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
13.3 6486 2.0 129.7:1 4500 A503_129.7 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
12.9 6666 3.7 133.3:1 6740 A603_133.3 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
12.2 7033 1.9 140.6:1 4500 A503_140.6 S2 + M2SB4 P90 + BN90S4 N140TC 92...95

11.9 7205 3.4 144.0:1 6740 A603_144.0 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
11.1 7732 1.7 154.6:1 4500 A503_154.6 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
11.0 7805 3.2 156.0:1 6740 A603_156.0 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
10.0 8576 2.9 171.5:1 6740 A603_171.5 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
9.9 8671 1.5 173.4:1 4500 A503_173.4 S2 + M2SB4 P90 + BN90S4 N140TC 92...95

9.3 9291 2.7 185.8:1 6740 A603_185.8 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
9.0 9533 1.4 190.6:1 4500 A503_190.6 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
8.2 10322 1.3 211.0:1 4500 A504_211.0 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
7.8 10777 4.1 220.3:1 11200 A704_220.3 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
7.6 11060 2.2 226.1:1 6740 A604_226.1 S2 + M2SB4 P90 + BN90S4 N140TC 96...99

7.4 11349 1.2 232.0:1 4500 A504_232.0 S2 + M2SB4 P90 + BN90S4 N140TC 92...95
7.2 11672 3.8 238.6:1 11200 A704_238.6 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
6.5 12929 1.9 264.3:1 6740 A604_264.3 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
6.0 14005 1.8 286.3:1 6740 A604_286.3 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
5.4 15478 2.9 316.4:1 11200 A704_316.4 S2 + M2SB4 P90 + BN90S4 N140TC 100...103

5.3 15864 1.6 324.3:1 6740 A604_324.2 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
4.9 17180 1.4 351.2:1 6740 A604_351.2 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
4.7 18070 2.4 369.4:1 11200 A704_369.4 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
4.3 19577 2.3 400.2:1 11200 A704_400.2 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
4.3 19797 1.3 404.7:1 6740 A604_404.7 S2 + M2SB4 P90 + BN90S4 N140TC 96...99

3.9 21446 1.2 438.4:1 6740 A604_438.4 S2 + M2SB4 P90 + BN90S4 N140TC 96...99
3.6 23275 1.9 475.8:1 11200 A704_475.8 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
3.6 23427 3.0 478.9:1 14600 A804_478.9 S2 + M2SB4 P90 + BN90S4 N140TC 104...107
3.3 25212 1.8 515.4:1 11200 A704_515.4 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
3.1 27418 2.6 560.5:1 14600 A804_560.5 S2 + M2SB4 P90 + BN90S4 N140TC 104...107

2.9 29106 1.5 595.0:1 11200 A704_595.0 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
2.8 29703 2.4 607.2:1 14600 A804_607.2 S2 + M2SB4 P90 + BN90S4 N140TC 104...107
2.4 34414 2.1 703.5:1 14600 A804_703.5 S2 + M2SB4 P90 + BN90S4 N140TC 104...107

36
 1.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

2.4 34492 1.3 705.1:1 11200 A704_705.1 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
2.4 34629 3.6 707.9:1 16900 A904_707.9 S2 + M2SB4 P90 + BN90S4 N140TC 108...111
2.3 37368 1.2 763.9:1 11200 A704_763.9 S2 + M2SB4 P90 + BN90S4 N140TC 100...103
2.1 40577 1.7 829.5:1 14600 A804_829.5 S2 + M2SB4 P90 + BN90S4 N140TC 104...107
2.0 42319 2.9 865.1:1 16900 A904_865.1 S2 + M2SB4 P90 + BN90S4 N140TC 108...111

1.7 48967 1.4 1001:1 14600 A804_1001 S2 + M2SB4 P90 + BN90S4 N140TC 104...107
1.7 50141 2.5 1025:1 16900 A904_1025 S2 + M2SB4 P90 + BN90S4 N140TC 108...111
1.4 59777 2.1 1222:1 16900 A904_1222 S2 + M2SB4 P90 + BN90S4 N140TC 108...111
1.4 60511 1.2 1237:1 14600 A804_1237 S2 + M2SB4 P90 + BN90S4 N140TC 104...107
1.1 79834 1.6 1632:1 16900 A904_1632 S2 + M2SB4 P90 + BN90S4 N140TC 108...111

0.76 111225 1.1 1507:1 16900 A904_1507 S3 + M3SA6 P90 + BN90L6 N180TC 108...111

2 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

315 377 3.3 5.5:1 590 A102_5.5 S3 + M3SA4 P90 + BN90LA4 N140TC 76...79
239 497 2.5 7.2:1 630 A102_7.2 S3 + M3SA4 P90 + BN90LA4 N140TC 76...79
236 502 3.7 7.3:1 690 A202_7.3 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83
213 556 3.3 5.4:1 710 A202_5.4 S3 + M3LA6 P100 + BN100LA6 N180TC 80...83
209 568 2.2 5.5:1 640 A102_5.5 S3 + M3LA6 P100 + BN100LA6 N180TC 76...79

183 646 2.9 9.4:1 730 A202_9.4 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83
179 662 1.9 9.6:1 660 A102_9.6 S3 + M3SA4 P90 + BN90LA4 N140TC 76...79
166 712 2.8 10.3:1 750 A202_10.3 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83
163 727 1.8 10.6:1 670 A102_10.6 S3 + M3SA4 P90 + BN90LA4 N140TC 76...79
144 824 2.3 12.0:1 770 A202_12.0 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83

140 848 1.5 12.3:1 680 A102_12.3 S3 + M3SA4 P90 + BN90LA4 N140TC 76...79
127 934 3.5 13.6:1 1180 A302_13.6 S3 + M3SA4 P90 + BN90LA4 N140TC 84...87
123 960 1.4 13.9:1 690 A102_13.9 S3 + M3SA4 P90 + BN90LA4 N140TC 76...79
122 970 2.2 14.1:1 790 A202_14.1 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83
110 1074 2.1 10.3:1 800 A202_10.3 S3 + M3LA6 P100 + BN100LA6 N180TC 80...83

109 1087 3.2 10.5:1 1220 A302_10.5 S3 + M3LA6 P100 + BN100LA6 N180TC 84...87
96 1239 2.9 18.0:1 1260 A302_18.0 S3 + M3SA4 P90 + BN90LA4 N140TC 84...87
95 1247 1.8 18.1:1 820 A202_18.1 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83
84 1410 2.6 13.6:1 1290 A302_13.6 S3 + M3LA6 P100 + BN100LA6 N180TC 84...87
81 1463 1.5 14.1:1 840 A202_14.1 S3 + M3LA6 P100 + BN100LA6 N180TC 80...83

76 1562 3.9 22.7:1 2740 A412_22.7 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91
76 1567 2.3 22.8:1 1320 A302_22.8 S3 + M3SA4 P90 + BN90LA4 N140TC 84...87
74 1592 1.4 23.1:1 850 A202_23.1 S3 + M3SA4 P90 + BN90LA4 N140TC 80...83
61 1951 3.3 28.3:1 2920 A412_28.3 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91

37
 2 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

59 2019 1.8 29.3:1 1380 A302_29.3 S3 + M3SA4 P90 + BN90LA4 N140TC 84...87
48 2473 2.8 35.9:1 3100 A412_35.9 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91
47 2525 1.4 36.6:1 1420 A302_36.6 S3 + M3SA4 P90 + BN90LA4 N140TC 84...87
40 2992 1.2 43.4:1 1450 A302_43.4 S3 + M3SA4 P90 + BN90LA4 N140TC 84...87
38 3105 2.4 45.1:1 3300 A412_45.1 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91

33 3446 3.9 51.7:1 4430 A503_51.7 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
32 3661 2.1 53.1:1 3370 A412_53.1 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91
26.9 4261 3.1 63.9:1 4500 A503_63.9 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
26.8 4420 1.7 64.2:1 3370 A412_64.2 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91
25.3 4684 1.6 45.1:1 3370 A412_45.1 S3 + M3LA6 P100 + BN100LA6 N180TC 88...91

24.5 4684 2.8 70.2:1 4500 A503_70.2 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
21.7 5459 1.4 79.2:1 3370 A412_79.2 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91
21.1 5432 2.4 81.5:1 4500 A503_81.5 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
19.9 5759 4.3 86.4:1 6740 A603_86.4 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
19.2 5972 2.2 89.5:1 4500 A503_89.5 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95

18.5 6187 1.1 92.8:1 3370 A413_92.8 S3 + M3SA4 P90 + BN90LA4 N140TC 88...91
17.3 6636 3.7 99.5:1 6740 A603_99.5 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
17.3 6638 2.0 99.5:1 4500 A503_99.5 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
15.7 7297 1.8 109.4:1 4500 A503_109.4 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
14.0 8205 3.0 123.0:1 6740 A603_123.0 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99

13.3 8648 1.5 129.7:1 4500 A503_129.7 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
12.9 8888 2.8 133.3:1 6740 A603_133.3 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
12.2 9378 1.4 140.6:1 4500 A503_140.6 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
11.9 9606 2.6 144.0:1 6740 A603_144.0 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
11.2 10249 4.3 153.7:1 11200 A703_153.7 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103

11.1 10310 1.3 154.6:1 4500 A503_154.6 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95
11.0 10407 2.4 156.0:1 6740 A603_156.0 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
10.1 11075 4.0 169.8:1 11200 A704_169.8 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
10.0 11435 2.2 171.5:1 6740 A603_171.5 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
9.9 11561 1.1 173.4:1 4500 A503_173.4 S3 + M3SA4 P90 + BN90LA4 N140TC 92...95

9.4 11995 3.7 183.9:1 11200 A704_183.9 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
9.3 12388 2.0 185.8:1 6740 A603_185.8 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
8.2 13612 1.8 208.7:1 6740 A604_208.7 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
7.8 14369 3.1 220.3:1 11200 A704_220.3 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
7.6 14747 1.7 226.1:1 6740 A604_226.1 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99

7.2 15562 2.8 238.6:1 11200 A704_238.6 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
6.5 17239 1.4 264.3:1 6740 A604_264.3 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
6.0 18674 1.3 286.3:1 6740 A604_286.3 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
5.9 19045 2.3 292.0:1 11200 A704_292.0 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
5.4 20637 2.1 316.4:1 11200 A704_316.4 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103

5.3 21152 1.2 324.2:1 6740 A604_324.2 S3 + M3SA4 P90 + BN90LA4 N140TC 96...99
4.7 24094 1.8 369.4:1 11200 A704_369.4 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
4.5 25013 2.8 383.5:1 14600 A804_383.5 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107

38
 2 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

4.3 26102 1.7 400.2:1 11200 A704_400.2 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
3.9 28835 2.5 442.1:1 14600 A804_442.1 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107
3.6 31033 1.4 475.8:1 11200 A704_475.8 S3 + M3SA4 P90 + BN90LA4 N140TC 100...103
3.6 31236 2.3 478.9:1 14600 A804_478.9 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107
3.5 31738 3.9 486.6:1 16900 A904_486.6 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111

3.1 36219 3.4 555.3:1 16900 A904_555.3 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111
3.1 36558 1.9 560.5:1 14600 A804_560.5 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107
2.9 39238 3.2 601.6:1 16900 A904_601.6 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111
2.8 39604 1.8 607.2:1 14600 A804_607.2 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107
2.4 45885 1.5 703.5:1 14600 A804_703.5 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107

2.4 46172 2.7 707.9:1 16900 A904_707.9 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111
2.0 56425 2.2 865.1:1 16900 A904_865.1 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111
1.9 58616 1.2 898.7:1 14600 A804_898.7 S3 + M3SA4 P90 + BN90LA4 N140TC 104...107
1.5 72463 1.7 1111:1 16900 A904_1111 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111
1.3 86356 1.4 1324:1 16900 A904_1324 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111

1.1 106445 1.2 1632:1 16900 A904_1632 S3 + M3SA4 P90 + BN90LA4 N140TC 108...111

3 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

321 553 3.4 5.4:1 610 A202_5.4 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83
315 565 2.2 5.5:1 550 A102_5.5 S3 + M3LA4 P100 + BN100LA4 N180TC 76...79
245 726 3.7 7.0:1 950 A302_7.0 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
239 745 1.7 7.2:1 570 A102_7.2 S3 + M3LA4 P100 + BN100LA4 N180TC 76...79
236 753 2.5 7.3:1 640 A202_7.3 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83

213 834 2.2 5.4:1 660 A202_5.4 S3 + M3LC6 P112 + BN112M6 80...83
211 844 3.1 5.4:1 990 A302_5.4 S3 + M3LC6 P112 + BN112M6 84...87
209 852 1.5 5.5:1 580 A102_5.5 S3 + M3LC6 P112 + BN112M6 76...79
185 962 2.8 9.3:1 1020 A302_9.3 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
183 969 1.9 9.4:1 670 A202_9.4 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83

179 994 1.2 9.6:1 580 A102_9.6 S3 + M3LA4 P100 + BN100LA4 N180TC 76...79
170 1047 4.5 10.1:1 2130 A412_10.1 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
166 1068 1.9 10.3:1 680 A202_10.3 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83
165 1080 2.8 10.5:1 1050 A302_10.5 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
163 1091 1.2 10.6:1 580 A102_10.6 S3 + M3LA4 P100 + BN100LA4 N180TC 76...79

146 1213 4.0 11.7:1 2220 A412_11.7 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
146 1217 2.2 11.8:1 1070 A302_11.8 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
144 1236 1.5 12.0:1 690 A202_12.0 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83
127 1402 2.3 13.6:1 1100 A302_13.6 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87

39
 3 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

125 1421 3.6 13.8:1 2320 A412_13.8 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
122 1454 1.5 14.1:1 700 A202_14.1 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83
113 1579 3.4 10.1:1 2380 A412_10.1 S3 + M3LC6 P112 + BN112M6 N210TC 88...91
110 1611 1.4 10.3:1 700 A202_10.3 S3 + M3LC6 P112 + BN112M6 80...83
109 1630 2.1 10.5:1 1130 A302_10.5 S3 + M3LC6 P112 + BN112M6 84...87

97 1836 3.0 17.8:1 2500 A412_17.8 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
96 1858 1.9 18.0:1 1160 A302_18.0 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
95 1871 1.2 18.1:1 710 A202_18.1 S3 + M3LA4 P100 + BN100LA4 N180TC 80...83
84 2115 1.7 13.6:1 1180 A302_13.6 S3 + M3LC6 P112 + BN112M6 84...87
83 2145 2.8 13.8:1 2590 A412_13.8 S3 + M3LC6 P112 + BN112M6 N210TC 88...91

76 2343 2.6 22.7:1 2650 A412_22.7 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
76 2351 1.5 22.8:1 1190 A302_22.8 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
61 2927 2.2 28.3:1 2790 A412_28.3 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
59 3028 1.2 29.3:1 1210 A302_29.3 S3 + M3LA4 P100 + BN100LA4 N180TC 84...87
48 3710 1.9 35.9:1 2940 A412_35.9 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91

47 3630 3.7 24.0:1 3840 A503_24.0 S3 + M3LC6 P112 + BN112M6 N210TC 92...95
38 4502 2.9 45.0:1 4020 A503_45.0 S3 + M3LA4 P100 + BN100LA4 N180TC 92...95
38 4657 1.6 45.1:1 3080 A412_45.1 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
32 5491 1.4 53.1:1 3170 A412_53.1 S3 + M3LA4 P100 + BN100LA4 N180TC 88...91
30 5683 2.3 56.8:1 4200 A503_56.8 S3 + M3LA4 P100 + BN100LA4 N180TC 92...95

24.5 7026 1.9 70.2:1 4340 A503_70.2 S3 + M3LA4 P100 + BN100LA4 N180TC 92...95
24.4 7043 3.5 70.4:1 6740 A603_70.4 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
19.2 8957 1.5 89.5:1 4450 A503_89.5 S3 + M3LA4 P100 + BN100LA4 N180TC 92...95
16.0 10784 2.3 107.8:1 6740 A603_107.8 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
15.7 10946 1.2 109.4:1 4500 A503_109.4 S3 + M3LA4 P100 + BN100LA4 N180TC 92...95

13.2 13071 3.4 130.7:1 11200 A703_130.7 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
12.9 13333 1.9 133.3:1 6740 A603_133.3 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
12.1 14191 3.1 141.9:1 11200 A703_141.9 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
11.9 14409 1.7 144.0:1 6740 A603_144.0 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
11.2 15373 2.9 153.7:1 11200 A703_153.7 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103

11.0 15610 1.6 156.0:1 6740 A603_156.0 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
10.1 16612 2.7 169.8:1 11200 A704_169.8 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
10.0 17152 1.4 171.5:1 6740 A603_171.5 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
9.3 18002 2.5 184.0:1 11200 A704_183.9 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
9.3 18582 1.3 185.8:1 6740 A603_185.8 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99

8.2 20418 1.2 208.7:1 6740 A604_208.7 S3 + M3LA4 P100 + BN100LA4 N180TC 96...99
7.8 21553 2.1 220.3:1 11200 A704_220.3 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
7.4 22756 3.1 232.6:1 14600 A804_232.6 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107
7.2 23344 1.9 238.6:1 11200 A704_238.6 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
6.2 27130 2.6 277.3:1 14600 A804_277.3 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107

5.9 28568 1.5 292.0:1 11200 A704_292.0 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
5.7 29390 2.4 300.4:1 14600 A804_300.4 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107
5.4 30955 1.4 316.4:1 11200 A704_316.4 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103

40
 3 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

4.9 34634 2.0 354.0:1 14600 A804_345.0 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107
4.5 37520 1.9 383.5:1 14600 A804_383.5 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107
4.5 37706 3.3 385.4:1 16900 A904_385.4 S3 + M3LA4 P100 + BN100LA4 N180TC 108...111
4.3 39154 1.1 400.2:1 11200 A704_400.2 S3 + M3LA4 P100 + BN100LA4 N180TC 100...103
3.9 43253 1.6 442.1:1 14600 A804_442.1 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107

3.6 46853 1.5 478.9:1 14600 A804_478.9 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107
3.5 47607 2.6 486.6:1 16900 A904_486.6 S3 + M3LA4 P100 + BN100LA4 N180TC 108...111
3.1 54328 2.3 555.3:1 16900 A904_555.3 S3 + M3LA4 P100 + BN100LA4 N180TC 108...111
3.1 54837 1.3 560.5:1 14600 A804_560.5 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107
2.8 59406 1.2 607.2:1 14600 A804_607.2 S3 + M3LA4 P100 + BN100LA4 N180TC 104...107

2.4 69258 1.8 707.9:1 16900 A904_707.9 S3 + M3LA4 P100 + BN100LA4 N180TC 108...111
2.0 84637 1.5 865.1:1 16900 A904_865.1 S3 + M3LA4 P100 + BN100LA4 N180TC 108...111
1.5 108695 1.1 1111:1 16900 A904_1111 S3 + M3LA4 P100 + BN100LA4 N180TC 108...111

5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

323 916 2.0 5.4:1 520 A202_5.4 S3 + M3LC4 P100 + BN100LC4 N180TC 80...83
320 927 2.9 5.4:1 810 A302_5.4 S3 + M3LC4 P100 + BN100LC4 N180TC 84...87
317 936 1.3 5.5:1 430 A102_5.5 S3 + M3LC4 P100 + BN100LC4 N180TC 76...79
246 1203 2.2 7.0:1 850 A302_7.0 S3 + M3LC4 P100 + BN100LC4 N180TC 84...87
243 1220 4.0 7.1:1 1840 A412_7.1 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91

237 1248 1.5 7.3:1 520 A202_7.3 S3 + M3LC4 P100 + BN100LC4 N180TC 80...83
188 1575 3.1 9.2:1 1960 A412_9.2 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91
186 1594 1.7 9.3:1 880 A302_9.3 S3 + M3LC4 P100 + BN100LC4 N180TC 84...87
171 1734 2.7 10.1:1 2010 A412_10.1 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91
165 1790 1.7 10.5:1 890 A302_10.5 S3 + M3LC4 P100 + BN100LC4 N180TC 84...87

147 2010 2.4 11.7:1 2080 A412_11.7 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91
147 2017 1.3 11.8:1 890 A302_11.8 S3 + M3LC4 P100 + BN100LC4 N180TC 84...87
128 2323 1.4 13.6:1 900 A302_13.6 S3 + M3LC4 P100 + BN100LC4 N180TC 84...87
126 2355 2.2 13.8:1 2160 A412_13.8 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91
114 2609 2.1 10.1:1 2200 A412_10.1 S4 + M4LA6 P132 + BN132M6 N210TC 88...91

104 2837 3.7 16.6:1 3210 A502_16.6 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95
97 3042 1.8 17.8:1 2270 A412_17.8 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91
84 3543 1.7 13.8:1 2340 A412_13.8 S4 + M4LA6 P132 + BN132M6 N210TC 88...91
83 3582 3.0 20.9:1 3420 A502_20.9 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95
76 3883 1.6 22.7:1 2380 A412_22.7 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91

41
 5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

72 3986 3.3 24.0:1 3150 A503_24.0 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95
65 4382 3.0 26.4:1 3190 A503_26.4 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95
61 4849 1.3 28.3:1 2450 A412_28.3 S3 + M3LC4 P100 + BN100LC4 N180TC 88...91
50 5686 4.4 34.3:1 6740 A603_34.3 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
49 5901 2.2 35.6:1 3300 A503_35.6 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95

38 7460 1.8 45.0:1 3350 A503_45.0 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95
38 7490 3.3 45.2:1 6740 A603_45.2 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
31 9217 2.7 55.6:1 6740 A603_55.6 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
30 9417 1.4 56.8:1 3350 A503_56.8 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95
27.1 10590 1.3 63.9:1 3330 A503_63.9 S3 + M3LC4 P100 + BN100LC4 N180TC 92...95

25.8 11096 4.0 66.9:1 11200 A703_66.9 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
24.6 11670 2.1 70.4:1 6740 A603_70.4 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
20.1 14245 3.1 85.9:1 11200 A703_85.9 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
20.0 14315 1.7 86.4:1 6740 A603_86.4 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
16.6 17278 2.6 104.2:1 11200 A703_104.2 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103

16.0 17869 1.4 107.8:1 6740 A603_107.8 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
14.3 19993 2.2 120.6:1 11200 A703_120.6 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
14.1 20393 1.2 123.0:1 6740 A603_123.0 S3 + M3LC4 P100 + BN100LC4 N180TC 96...99
12.2 23515 1.9 141.9:1 11200 A703_141.9 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
12.0 23992 3.0 144.7:1 14600 A803_144.7 S3 + M3LC4 P100 + BN100LC4 N180TC 104...107

11.3 25474 1.7 153.7:1 11200 A703_153.7 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
11.0 25991 2.7 156.8:1 14600 A803_156.8 S3 + M3LC4 P100 + BN100LC4 N180TC 104...107
10.2 27527 1.6 169.8:1 11200 A704_169.8 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
10.1 27771 2.5 171.3:1 14600 A804_171.3 S3 + M3LC4 P100 + BN100LC4 N180TC 104...107
9.6 29181 4.2 180.0:1 16900 A904_180.0 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111

9.4 29813 1.5 183.9:1 11200 A704_183.9 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
7.9 35714 1.2 220.3:1 11200 A704_220.3 S3 + M3LC4 P100 + BN100LC4 N180TC 100...103
7.6 36703 3.4 226.4:1 16900 A904_226.4 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111
7.4 37708 1.9 232.6:1 14600 A804_232.6 S3 + M3LC4 P100 + BN100LC4 N180TC 104...107
6.2 44955 1.6 277.3:1 14600 A804_277.3 S3 + M3LC4 P100 + BN100LC4 N180TC 104...107

5.7 49429 2.5 304.9:1 16900 A904_304.9 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111
4.9 57389 1.2 354.0:1 14600 A804_354.0 S3 + M3LC4 P100 + BN100LC4 N180TC 104...107
4.5 62480 2.0 385.4:1 16900 A904_385.4 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111
3.6 78886 1.6 486.6:1 17100 A904_486.6 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111
3.1 90023 1.4 555.3:1 17100 A904_555.3 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111

2.9 97529 1.3 601.6:1 16900 A904_601.6 S3 + M3LC4 P100 + BN100LC4 N180TC 108...111

42
 7.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

330 1347 3.6 5.2:1 1630 A412_5.2 S4 + M4SA4 P132 + BN132S4 N210TC 88...91
243 1829 2.7 7.1:1 1750 A412_7.1 S4 + M4SA4 P132 + BN132S4 N210TC 88...91
217 2044 2.4 5.2:1 1800 A412_5.2 S4 + M4LB6 P132 + BN132MB6 88...91
188 2362 2.1 9.2:1 1850 A412_9.2 S4 + M4SA4 P132 + BN132S4 N210TC 88...91
171 2602 1.8 10.1:1 1900 A412_10.1 S4 + M4SA4 P132 + BN132S4 N210TC 88...91

160 2776 1.8 7.1:1 1920 A412_7.1 S4 + M4LB6 P132 + BN132MB6 88...91
147 3015 1.6 11.7:1 1950 A412_11.7 S4 + M4SA4 P132 + BN132S4 N210TC 88...91
132 3366 2.9 13.1:1 2900 A502_13.1 S4 + M4SA4 P132 + BN132S4 N210TC 92...95
126 3533 1.5 13.8:1 2010 A412_13.8 S4 + M4SA4 P132 + BN132S4 N210TC 88...91
113 3948 1.4 10.1:1 2050 A412_10.1 S4 + M4LB6 P132 + BN132MB6 88...91

104 4256 2.5 16.6:1 3080 A502_16.6 S4 + M4SA4 P132 + BN132S4 N210TC 92...95
97 4562 1.2 17.8:1 2090 A412_17.8 S4 + M4SA4 P132 + BN132S4 N210TC 88...91
84 5289 3.3 20.6:1 6740 A602_20.6 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
83 5373 2.0 20.9:1 3260 A502_20.9 S4 + M4SA4 P132 + BN132S4 N210TC 92...95
72 5979 2.2 24.0:1 2830 A503_24.0 S4 + M4SA4 P132 + BN132S4 N210TC 92...95

67 6393 3.9 25.7:1 6740 A603_25.7 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
62 6925 3.6 27.9:1 6740 A603_27.9 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
55 8027 2.2 20.6:1 6740 A602_20.6 S4 + M4LB6 P132 + BN132MB6 96...99
53 8051 1.6 32.4:1 2850 A503_32.4 S4 + M4SA4 P132 + BN132S4 N210TC 92...95
50 8528 2.9 34.3:1 6740 A603_34.3 S4 + M4SA4 P132 + BN132S4 N210TC 96...99

49 8851 1.5 35.6:1 2850 A503_35.6 S4 + M4SA4 P132 + BN132S4 N210TC 92...95
41 10371 2.4 41.7:1 6740 A603_41.7 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
38 11190 1.2 45.0:1 2810 A503_45.0 S4 + M4SA4 P132 + BN132S4 N210TC 92...95
35 12183 3.6 49.0:1 11200 A703_49.0 S4 + M4SA4 P132 + BN132S4 N210TC 100...103
34 12762 1.9 51.3:1 6740 A603_51.3 S4 + M4SA4 P132 + BN132S4 N210TC 96...99

31 13825 1.8 55.6:1 6740 A603_55.6 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
30 14339 3.1 57.7:1 11200 A703_57.7 S4 + M4SA4 P132 + BN132S4 N210TC 100...103
25.8 16644 2.7 66.9:1 11200 A703_66.9 S4 + M4SA4 P132 + BN132S4 N210TC 100...103
24.6 17505 1.4 70.4:1 6740 A603_70.4 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
21.8 19724 2.2 79.3:1 11200 A703_79.3 S4 + M4SA4 P132 + BN132S4 N210TC 100...103

21.7 19821 1.3 79.7:1 6740 A603_79.7 S4 + M4SA4 P132 + BN132S4 N210TC 96...99
21.0 20468 3.5 82.3:1 14600 A803_82.3 S4 + M4SA4 P132 + BN132S4 N210TC 104...107
18.0 23876 3.0 96.0:1 14600 A803_96.0 S4 + M4SA4 P132 + BN132S4 N210TC 104...107
18.0 23924 1.8 96.2:1 11200 A703_96.2 S4 + M4SA4 P132 + BN132S4 N210TC 100...103
14.9 28831 2.5 116.0:1 14600 A803_116.0 S4 + M4SA4 P132 + BN132S4 N210TC 104...107

14.3 29990 1.5 120.6:1 11200 A703_120.6 S4 + M4SA4 P132 + BN132S4 N210TC 100...103
12.4 34659 3.3 139.4:1 16900 A903_139.4 S4 + M4SA4 P132 + BN132S4 N210TC 108...111
12.2 35272 1.3 141.9:1 11200 A703_141.9 S4 + M4SA4 P132 + BN132S4 N210TC 100...103
12.0 35988 2.0 144.7:1 14600 A803_144.7 S4 + M4SA4 P132 + BN132S4 N210TC 104...107
10.2 41291 1.1 169.8:1 11200 A704_169.8 S4 + M4SA4 P132 + BN132S4 N210TC 100...103

10.1 41656 1.7 171.3:1 14600 A804_171.3 S4 + M4SA4 P132 + BN132S4 N210TC 104...107
7.6 55055 2.3 226.4:1 16900 A904_226.4 S4 + M4SA4 P132 + BN132S4 N210TC 108...111
7.4 56562 1.3 232.6:1 14600 A804_232.6 S4 + M4SA4 P132 + BN132S4 N210TC 104...107

43
 7.5 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

5.7 74144 1.7 304.9:1 16900 A904_304.9 S4 + M4SA4 P132 + BN132S4 N210TC 108...111
4.5 93719 1.3 385.4:1 16900 A904_385.4 S4 + M4SA4 P132 + BN132S4 N210TC 108...111
3.7 112517 1.1 304.9:1 16900 A904_304.9 S4 + M4LB6 P132 + BN132MB6 108...111

10 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

332 1786 2.7 5.2:1 1560 A412_5.2 S4 + M4LA4 P132 + BN132MA4 N210TC 88...91
244 2425 2.0 7.1:1 1660 A412_7.1 S4 + M4LA4 P132 + BN132MA4 N210TC 88...91
189 3132 1.6 9.2:1 1730 A412_9.2 S4 + M4LA4 P132 + BN132MA4 N210TC 88...91
172 3449 1.4 10.1:1 1760 A412_10.1 S4 + M4LA4 P132 + BN132MA4 N210TC 88...91
148 3998 1.2 11.7:1 1790 A412_11.7 S4 + M4LA4 P132 + BN132MA4 N210TC 88...91

133 4463 2.2 13.1:1 2790 A502_13.1 S4 + M4LA4 P132 + BN132MA4 N210TC 92...95
105 5642 1.9 16.6:1 2940 A502_16.6 S4 + M4LA4 P132 + BN132MA4 N210TC 92...95
104 5698 3.1 16.7:1 6740 A602_16.7 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
84 7012 2.5 20.6:1 6740 A602_20.6 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
83 7122 1.5 20.9:1 3080 A502_20.9 S4 + M4LA4 P132 + BN132MA4 N210TC 92...95

72 7927 1.7 24.0:1 2430 A503_24.0 S4 + M4LA4 P132 + BN132MA4 N210TC 92...95
66 8714 1.5 26.4:1 2430 A503_26.4 S4 + M4LA4 P132 + BN132MA4 N210TC 92...95
62 9181 2.7 27.9:1 6740 A603_27.9 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
51 11306 2.2 34.3:1 6740 A603_34.3 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
49 11734 1.1 35.6:1 2270 A503_35.6 S4 + M4LA4 P132 + BN132MA4 N210TC 92...95

39 14895 1.7 45.2:1 6740 A603_45.2 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
38 14909 2.8 45.2:1 11200 A703_45.2 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103
32 18189 3.9 55.2:1 14100 A803_55.2 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107
31 18328 1.4 55.6:1 6740 A603_55.6 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
30 19009 2.3 57.7:1 11200 A703_57.7 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103

26.8 21421 1.2 65.0:1 6740 A603_65.0 S4 + M4LA4 P132 + BN132MA4 N210TC 96...99
26.0 22019 3.2 66.8:1 14600 A803_66.8 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107
26.0 22065 2.0 66.9:1 11200 A703_66.9 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103
21.9 26148 1.7 79.3:1 11200 A703_79.3 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103
21.1 27134 2.6 82.3:1 14600 A803_82.3 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107

20.2 28326 1.6 85.9:1 11200 A703_85.9 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103
19.5 29395 2.4 89.2:1 14600 A803_89.2 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107
18.1 31715 1.4 96.2:1 11200 A703_96.2 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103
16.7 34290 2.1 104.0:1 14600 A803_104.0 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107
16.7 34358 1.3 104.2:1 11200 A703_104.2 S4 + M4LA4 P132 + BN132MA4 N210TC 100...103

16.3 35209 3.5 106.8:1 16900 A903_106.8 S4 + M4LA4 P132 + BN132MA4 N210TC 108...111
13.9 41405 1.7 125.6:1 14600 A803_125.6 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107

44
 10 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

13.7 41744 2.8 126.6:1 16900 A903_126.6 S4 + M4LA4 P132 + BN132MA4 N210TC 108...111
10.5 53546 2.3 166.1:1 16900 A904_166.1 S4 + M4LA4 P132 + BN132MA4 N210TC 108...111
10.2 55222 1.3 171.3:1 14600 A804_171.3 S4 + M4LA4 P132 + BN132MA4 N210TC 104...107
7.7 72984 1.7 226.4:1 16900 A904_226.4 S4 + M4LA4 P132 + BN132MA4 N210TC 108...111
5.7 98290 1.3 304.9:1 16900 A904_304.9 S4 + M4LA4 P132 + BN132MA4 N210TC 108...111

15 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

225 3951 2.1 7.7:1 2320 A502_7.7 S4 + M4LC4 P160 + BN160MR4 N250TC 92...95
179 4971 1.8 9.7:1 2450 A502_9.7 S4 + M4LC4 P160 + BN160MR4 N250TC 92...95
169 5268 3.4 10.3:1 6740 A602_10.3 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99
150 5927 1.4 7.7:1 2540 A502_7.7 P160 + BN160L6 92...95
137 6488 2.7 12.7:1 6740 A602_12.7 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99

133 6694 1.5 13.1:1 2590 A502_13.1 S4 + M4LC4 P160 + BN160MR4 N250TC 92...95
119 7457 1.2 9.7:1 2650 A502_9.7 P160 + BN160L6 92...95
105 8463 1.3 16.6:1 2700 A502_16.6 S4 + M4LC4 P160 + BN160MR4 N250TC 92...95
104 8548 2.1 16.7:1 6740 A602_16.7 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99
88 9723 3.4 19.7:1 10000 A703_19.7 S4 + M4LC4 P160 + BN160MR4 N250TC 100...103

84 10518 1.7 20.6:1 6740 A602_20.6 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99
74 11629 3.3 23.5:1 10500 A703_23.5 P160 + BN160MR4 N250TC 100...103
72 11890 1.1 24.0:1 1750 A503_24.0 S4 + M4LC4 P160 + BN160MR4 N250TC 92...95
68 12712 1.9 25.7:1 6740 A603_25.7 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99
63 13737 2.7 27.8:1 10900 A703_27.8 P160 + BN160MR4 N250TC 100...103

62 13771 1.8 27.9:1 6740 A603_27.9 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99
51 16959 1.5 34.3:1 6740 A603_34.3 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99
45 18977 2.3 38.4:1 11200 A703_38.4 S4 + M4LC4 P160 + BN160MR4 N250TC 100...103
45 19035 3.5 38.5:1 12500 A803_38.5 P160 + BN160MR4 N250TC 104...107
39 22342 1.1 45.2:1 6740 A603_45.2 S4 + M4LC4 P160 + BN160MR4 N250TC 96...99

38 22363 1.9 45.2:1 11200 A703_45.2 S4 + M4LC4 P160 + BN160MR4 N250TC 100...103
36 23823 3.0 48.2:1 13100 A803_48.2 S4 + M4LC4 P160 + BN160MR4 N250TC 104...107
32 27283 2.6 55.2:1 13500 A803_55.2 S4 + M4LC4 P160 + BN160MR4 N250TC 104...107
30 28513 1.6 57.7:1 11200 A703_57.7 S4 + M4LC4 P160 + BN160MR4 N250TC 100...103
24.0 35781 2.0 72.4:1 14200 A803_72.4 S4 + M4LC4 P160 + BN160MR4 N250TC 104...107

24.0 35855 1.2 72.5:1 11200 A703_72.5 S4 + M4LC4 P160 + BN160MR4 N250TC 100...103
20.0 43049 2.9 87.1:1 16900 A903_87.1 S4 + M4LC4 P160 + BN160MR4 N250TC 108...111
19.5 44092 1.6 89.2:1 14600 A803_89.2 S4 + M4LC4 P160 + BN160MR4 N250TC 104...107
15.0 57331 1.2 116.0:1 14600 A803_116.0 S4 + M4LC4 P160 + BN160MR4 N250TC 104...107
14.9 57800 2.1 116.9:1 16900 A903_116.9 S4 + M4LC4 P160 + BN160MR4 N250TC 108...111

45
 15 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

8.3 101063 1.2 209.0:1 16900 A904_209.0 S4 + M4LC4 P160 + BN160MR4 N250TC 108...111
7.7 111993 1.1 151.0:1 16900 A903_151.0 S5 + M5SB6 P160 + BN160L6 108...111

20 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

223 5325 3.3 7.9:1 6380 A602_7.9 S5 + M5SB4 P160 + BN160L4 N250TC 96...99
180 6591 1.3 9.7:1 2270 A502_9.7 P160 + BN160L4 N250TC 92...95
170 6984 2.5 10.3:1 6740 A602_10.3 S5 + M5SB4 P160 + BN160L4 N250TC 96...99
138 8601 2.1 12.7:1 6740 A602_12.7 S5 + M5SB4 P160 + BN160L4 N250TC 96...99
134 8578 4.0 13.1:1 8830 A703_13.1 S5 + M5SB4 P160 + BN160L4 N250TC 100...103

134 8874 1.1 13.1:1 2380 A502_13.1 P160 + BN160L4 N250TC 92...95
114 10097 3.2 15.4:1 9190 A703_15.4 S5 + M5SB4 P160 + BN160L4 N250TC 100...103
105 10939 3.2 16.7:1 9370 A703_16.7 S5 + M5SB4 P160 + BN160L4 N250TC 100...103
105 11332 1.6 16.7:1 6740 A602_16.7 S5 + M5SB4 P160 + BN160L4 N250TC 96...99
85 13944 1.3 20.6:1 6740 A602_20.6 S5 + M5SB4 P160 + BN160L4 N250TC 96...99

84 13731 4.2 20.9:1 10500 A803_20.9 S5 + M5SB4 P160 + BN160L4 N250TC 104...107
82 13964 2.5 21.3:1 9910 A703_21.3 S5 + M5SB4 P160 + BN160L4 N250TC 100...103
68 16852 1.5 25.7:1 6740 A603_25.7 S5 + M5SB4 P160 + BN160L4 N250TC 96...99
63 18212 2.0 27.8:1 10500 A703_27.8 P160 + BN160L4 N250TC 100...103
62 18500 3.2 28.2:1 11200 A803_28.2 P160 + BN160L4 N250TC 104...107

51 22482 1.1 34.3:1 6740 A603_34.3 S5 + M5SB4 P160 + BN160L4 N250TC 96...99
46 25159 1.7 38.4:1 11200 A703_38.4 S5 + M5SB4 P160 + BN160L4 N250TC 100...103
45 25235 2.7 38.5:1 12000 A803_38.5 P160 + BN160L4 N250TC 104...107
36 31582 2.2 48.2:1 12500 A803_48.2 S5 + M5SB4 P160 + BN160L4 N250TC 104...107
36 31659 3.9 48.3:1 16900 A903_48.3 S5 + M5SB4 P160 + BN160L4 N250TC 108...111

36 32118 1.4 49.0:1 11200 A703_49.0 S5 + M5SB4 P160 + BN160L4 N250TC 100...103
32 36169 2.0 55.2:1 12800 A803_55.2 S5 + M5SB4 P160 + BN160L4 N250TC 104...107
30 37800 1.2 57.7:1 11200 A703_57.7 S5 + M5SB4 P160 + BN160L4 N250TC 100...103
25.5 45063 2.7 68.8:1 16900 A903_68.8 S5 + M5SB4 P160 + BN160L4 N250TC 108...111
24.2 47435 1.5 72.4:1 13300 A803_72.4 S5 + M5SB4 P160 + BN160L4 N250TC 104...107

20.1 57070 2.2 87.1:1 16900 A903_87.1 S5 + M5SB4 P160 + BN160L4 N250TC 108...111
19.6 58454 1.2 89.2:1 13600 A803_89.2 S5 + M5SB4 P160 + BN160L4 N250TC 104...107
15.0 76626 1.6 116.9:1 16900 A903_116.9 S5 + M5SB4 P160 + BN160L4 N250TC 108...111
12.6 91367 1.2 139.4:1 16900 A903_139.4 S5 + M5SB4 P160 + BN160L4 N250TC 108...111
10.5 106479 1.2 166.1:1 16900 A904_166.1 P160 + BN160L4 N250TC 108...111

46
 25 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

226 6548 1.3 7.7:1 2080 A502_7.7 P180 + BN180M4 N280TC 92...95
223 6656 2.7 7.9:1 6290 A602_7.9 S5 + M5LA4 P180 + BN180M4 N280TC 96...99
185 7734 3.4 9.4:1 8000 A703_9.4 S5 + M5LA4 P180 + BN180M4 N280TC 100...103
180 8238 1.1 9.7:1 2140 A502_9.7 P180 + BN180M4 N280TC 92...95
171 8378 3.4 10.2:1 8180 A703_10.2 S5 + M5LA4 P180 + BN180M4 N280TC 100...103

170 8731 2.0 10.3:1 6720 A602_10.3 S5 + M5LA4 P180 + BN180M4 N280TC 96...99
145 9898 3.2 12.1:1 8520 A703_12.1 S5 + M5LA4 P180 + BN180M4 N280TC 100...103
138 10752 1.6 12.7:1 6740 A602_12.7 S5 + M5LA4 P180 + BN180M4 N280TC 96...99
134 10722 3.2 13.1:1 8680 A703_13.1 S5 + M5LA4 P180 + BN180M4 N280TC 100...103
114 12621 2.6 15.4:1 9010 A703_15.4 S5 + M5LA4 P180 + BN180M4 N280TC 100...103

105 13673 2.6 16.7:1 9190 A703_16.7 S5 + M5LA4 P180 + BN180M4 N280TC 100...103
105 14165 1.2 16.7:1 6740 A602_16.7 S5 + M5LA4 P180 + BN180M4 N280TC 96...99
90 15844 3.4 19.3:1 10100 A803_19.3 S5 + M5LA4 P180 + BN180M4 N280TC 104...107
89 16112 2.0 19.7:1 9510 A703_19.7 S5 + M5LA4 P180 + BN180M4 N280TC 100...103
77 18529 3.0 22.6:1 10400 A803_22.6 P180 + BN180M4 N280TC 104...107

74 19271 2.0 23.5:1 9890 A703_23.5 P180 + BN180M4 N280TC 100...103

63 22765 1.6 27.8:1 10200 A703_27.8 P180 + BN180M4 N280TC 100...103
63 22820 1.1 27.9:1 6740 A603_27.9 S5 + M5LA4 P180 + BN180M4 N280TC 96...99
62 23125 2.5 28.2:1 10900 A803_28.2 P180 + BN180M4 N280TC 104...107
49 29029 1.4 35.4:1 10600 A703_35.4 S5 + M5LA4 P180 + BN180M4 N280TC 100...103

49 29118 2.1 35.5:1 11400 A803_35.5 P180 + BN180M4 N280TC 104...107

39 36441 1.8 44.5:1 11800 A803_44.5 S5 + M5LA4 P180 + BN180M4 N280TC 104...107
39 36529 3.4 44.6:1 16100 A903_44.6 S5 + M5LA4 P180 + BN180M4 N280TC 108...111
39 37059 1.1 45.2:1 11000 A703_45.2 S5 + M5LA4 P180 + BN180M4 N280TC 100...103
32 45088 2.7 55.0:1 16900 A903_55.0 S5 + M5LA4 P180 + BN180M4 N280TC 108...111

32 45212 1.6 55.2:1 12200 A803_55.2 S5 + M5LA4 P180 + BN180M4 N280TC 104...107
25.5 56329 2.2 68.8:1 16900 A903_68.8 S5 + M5LA4 P180 + BN180M4 N280TC 108...111
24.2 59294 1.2 72.4:1 12500 A803_72.4 S5 + M5LA4 P180 + BN180M4 N280TC 104...107
17.7 80788 1.5 98.6:1 16900 A903_98.6 S5 + M5LA4 P180 + BN180M4 N280TC 108...111
13.8 103764 1.1 126.6:1 16900 A903_126.6 S5 + M5LA4 P180 + BN180M4 N280TC 108...111

30 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

226 7858 1.1 7.7:1 1970 A502_7.7 P180 + BN180L4 N280TC 92...95
223 7987 2.2 7.9:1 6210 A602_7.9 P180 + BN180L4 N280TC 96...99
185 9281 2.9 9.4:1 7890 A703_9.4 P180 + BN180L4 N280TC 100...103
171 10054 2.9 10.2:1 8050 A703_10.2 P180 + BN180L4 N280TC 100...103
170 10477 1.7 10.3:1 6590 A602_10.3 P180 + BN180L4 N280TC 96...99

47
 30 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

138 12902 1.4 12.7:1 6750 A602_12.7 P180 + BN180L4 N280TC 96...99
134 12867 2.6 13.1:1 8520 A703_13.0 P180 + BN180L4 N280TC 100...103
114 15146 2.2 15.4:1 8840 A703_15.4 P180 + BN180L4 N280TC 100...103
113 15192 3.5 15.5:1 9400 A803_15.5 P180 + BN180L4 N280TC 104...107
105 16408 2.2 16.7:1 8990 A703_16.7 P180 + BN180L4 N280TC 100...103

105 16458 3.5 16.7:1 9550 A803_16.7 P180 + BN180L4 N280TC 104...107
89 19335 1.7 19.6:1 9290 A703_19.7 P180 + BN180L4 N280TC 100...103
84 20597 2.8 20.9:1 10000 A803_20.9 P180 + BN180L4 N280TC 104...107
77 22235 2.5 22.6:1 10200 A803_22.6 P180 + BN180L4 N280TC 104...107
74 23125 1.6 23.5:1 9620 A703_23.5 P180 + BN180L4 N280TC 100...103

63 27318 1.4 27.8:1 9870 A703_27.8 P180 + BN180L4 N280TC 100...103

62 27750 2.1 28.2:1 10600 A803_28.2 P180 + BN180L4 N280TC 104...107
60 28588 4.0 29.1:1 14400 A903_29.0 P180 + BN180L4 N280TC 108...111
49 34835 1.1 35.4:1 10200 A703_35.4 P180 + BN180L4 N280TC 100...103
49 34941 1.8 35.5:1 11000 A803_35.5 P180 + BN180L4 N280TC 104...107

49 35221 3.5 35.8:1 15100 A903_35.8 P180 + BN180L4 N280TC 108...111

39 43729 1.5 44.5:1 11300 A803_44.5 P180 + BN180L4 N280TC 104...107
39 43835 2.8 44.6:1 15700 A903_44.6 P180 + BN180L4 N280TC 108...111
32 54106 2.3 55.0:1 16300 A903_55.0 P180 + BN180L4 N280TC 108...111
32 54254 1.3 55.2:1 11600 A803_55.2 P180 + BN180L4 N280TC 104...107

26.2 65679 1.1 66.8:1 11700 A803_66.8 P180 + BN180L4 N280TC 104...107
25.5 67595 1.8 68.8:1 16900 A903_68.8 P180 + BN180L4 N280TC 108...111
20.1 85606 1.4 87.1:1 16900 A903_87.0 P180 + BN180L4 N280TC 108...111
15.0 114939 1.1 116.9:1 16900 A903_116.9 P180 + BN180L4 N280TC 108...111

40 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

185 12374 2.0 9.4:1 7640 A703_9.4 P200 + BN200L4 100...103

178 12890 2.7 9.8:1 8210 A803_9.8 P200 + BN200L4 N320TC 104...107
171 13406 2.1 10.2:1 7800 A703_10.2 P200 + BN200L4 100...103
145 15836 1.8 12.1:1 8050 A703_12.1 P200 + BN200L4 100...103
143 16087 2.4 12.3:1 8610 A803_12.3 P200 + BN200L4 N320TC 104...107

134 17156 1.7 13.1:1 8180 A703_13.1 P200 + BN200L4 100...103

132 17427 2.2 13.3:1 8770 A803_13.3 P200 + BN200L4 N320TC 104...107
114 20194 1.5 15.4:1 8430 A703_15.4 P200 + BN200L4 100...103
113 20256 1.8 15.5:1 9020 A803_15.5 P200 + BN200L4 N320TC 104...107
105 21877 1.5 16.7:1 8570 A703_16.7 P200 + BN200L4 100...103

105 21944 1.8 16.7:1 9150 A803_16.7 P200 + BN200L4 N320TC 104...107

48
 40 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

83 27529 4.0 21.0:1 13000 A903_21.0 P200 + BN200L4 N320TC 108...111

73 31604 3.7 24.1:1 13300 A903_24.1 P200 + BN200L4 N320TC 108...111
71 32118 1.9 24.5:1 9730 A803_24.5 P200 + BN200L4 N320TC 104...107
62 36999 1.6 28.2:1 9910 A803_28.2 P200 + BN200L4 N320TC 104...107
60 38118 3.0 29.1:1 13800 A903_29.1 P200 + BN200L4 N320TC 108...111

49 46588 1.3 35.5:1 10100 A803_35.5 P200 + BN200L4 N320TC 104...107

49 46961 2.6 35.8:1 14300 A903_35.8 P200 + BN200L4 N320TC 108...111
36 63164 1.1 48.2:1 10300 A803_48.2 P200 + BN200L4 N320TC 104...107
36 63317 2.0 48.3:1 15000 A903_48.3 P200 + BN200L4 N320TC 108...111
32 72141 1.7 55.0:1 15300 A903_55.0 P200 + BN200L4 N320TC 108...111

29.4 78153 1.6 59.6:1 15400 A903_59.6 P200 + BN200L4 N320TC 108...111
23.5 97637 1.3 74.5:1 15700 A903_74.5 P200 + BN200L4 N320TC 108...111
20.1 114141 1.1 87.1:1 15800 A903_87.1 P200 + BN200L4 N320TC 108...111

50 hp
n2 T2 S i Rn2
Safety
[rpm] [lb·in] factor (ratio) [lb]

178 16112 3.3 9.8:1 7980 A803_9.8 P225 + BN225S4 N320TC 104...107
164 17455 3.3 10.6:1 8120 A803_10.7 P225 + BN225S4 N320TC 104...107
142 20155 2.7 12.3:1 8340 A803_12.3 P225 + BN225S4 N320TC 104...107
132 21784 2.7 13.2:1 8480 A803_13.3 P225 + BN225S4 N320TC 104...107
113 25320 2.1 15.4:1 8680 A803_15.5 P225 + BN225S4 N320TC 104...107

112 25522 3.8 15.5:1 11800 A903_15.6 P225 + BN225S4 N320TC 108...111
90 31688 1.7 19.3:1 8950 A803_19.3 P225 + BN225S4 N320TC 104...107
90 31765 3.2 19.3:1 12400 A903_19.4 P225 + BN225S4 N320TC 108...111
84 34329 1.7 20.9:1 9060 A803_20.9 P225 + BN225S4 N320TC 104...107
83 34412 3.2 21.0:1 12600 A903_21.0 P225 + BN225S4 N320TC 108...111

73 39505 2.9 24.1:1 12900 A903_24.1 P225 + BN225S4 N320TC 108...111

71 40147 1.5 24.5:1 9220 A803_24.5 P225 + BN225S4 N320TC 104...107
57 50103 1.1 30.5:1 9350 A803_30.6 P225 + BN225S4 N320TC 104...107
56 51617 2.4 31.5:1 13500 A903_31.5 P225 + BN225S4 N320TC 108...111
45 63088 1.1 38.5:1 9380 A803_38.5 P225 + BN225S4 N320TC 104...107

45 63593 1.9 38.8:1 13900 A903_38.8 P225 + BN225S4 N320TC 108...111

36 79147 1.6 48.3:1 14200 A903_48.3 P225 + BN225S4 N320TC 108...111
32 90176 1.4 55.0:1 14300 A903_55.0 P225 + BN225S4 N320TC 108...111
25.5 112658 1.1 68.7:1 14400 A903_68.8 P225 + BN225S4 N320TC 108...111

49
2.13 SPEED REDUCER RATING CHARTS

A 10 1,330 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

(ratio) n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]
A 102_ 5.5 636 650 6.9 — 410 318 650 3.5 220 550
A 102_ 7.2 486 810 6.6 — 430 243 820 3.3 140 580
A 102_ 9.6 365 900 5.5 — 470 182 1130 3.4 — 600
A 102_ 10.6 330 1110 6.1 120 450 165 1330 3.7 180 580
A 102_ 12.3 285 970 4.6 — 510 142 1220 2.9 — 650
A 102_ 13.9 252 1190 5.0 140 500 126 1330 2.8 240 670
A 102_ 18.6 188 1300 4.1 150 550 94 1330 2.1 270 760
A 102_ 23.8 147 1330 3.3 170 620 74 1330 1.6 270 850
A 102_ 28.6 122 1330 2.7 190 670 61 1330 1.4 280 920
A 102_ 35.1 100 1330 2.2 200 740 50 1330 1.1 290 1000
A 102_ 45.4 77 1330 1.7 200 830 39 1330 0.86 290 1120
A 102_ 51.3 68 1330 1.5 200 880 34 1330 0.76 290 1180
A 102_ 65.9 53 1330 1.2 210 980 26.6 1330 0.59 290 1240
A 102_ 76.4 46 1330 1.0 210 1040 22.9 1330 0.51 290 1240
A 102_ 91.6 38 1150 0.73 230 1160 19.1 1150 0.37 290 1240

A 10
i n1 = 1100 rpm n1 = 600 rpm
n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2
(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]
A 102_ 5.5 200 650 2.2 290 660 109 650 1.2 290 840
A 102_ 7.2 153 820 2.1 260 700 83 820 1.1 290 890
A 102_ 9.6 115 1130 2.2 110 730 63 1130 1.2 290 940
A 102_ 10.6 104 1330 2.3 290 720 57 1330 1.3 290 940
A 102_ 12.3 89 1330 2.0 40 770 49 1330 1.1 230 1000
A 102_ 13.9 79 1330 1.8 290 820 43 1330 1.0 290 1050
A 102_ 18.6 59 1330 1.3 290 930 32 1330 0.72 290 1180
A 102_ 23.8 46 1330 1.0 290 1030 25.2 1330 0.56 290 1120
A 102_ 28.6 38 1330 0.85 290 1110 21.0 1330 0.47 290 1120
A 102_ 35.1 31 1330 0.70 290 1210 17.1 1330 0.38 290 1120
A 102_ 45.4 24.2 1330 0.54 290 1240 13.2 1330 0.29 290 1120
A 102_ 51.3 21.4 1330 0.48 290 1240 11.7 1330 0.26 290 1120
A 102_ 65.9 16.7 1330 0.37 290 1240 9.1 1330 0.20 290 1120
A 102_ 76.4 14.4 1330 0.32 290 1240 7.9 1330 0.17 290 1120
A 102_ 91.6 12.0 1150 0.23 290 1240 6.6 1150 0.13 290 1120

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

50
 A 20 2,210 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 202_ 5.4 648 800 8.7 — 440 324 1010 5.5 — 550
A 202_ 7.3 479 920 7.4 — 480 240 1160 4.6 — 600
A 202_ 9.4 372 1020 6.3 — 520 186 1280 4.0 — 650
A 202_ 10.3 340 1620 9.2 — 440 170 1990 5.6 — 570
A 202_ 12.0 292 1130 5.5 — 560 146 1420 3.5 — 700
A 202_ 14.1 248 1760 7.3 — 500 124 2170 4.5 — 630
A 202_ 18.1 193 1910 6.2 — 540 97 2210 3.6 20 710
A 202_ 23.1 152 2050 5.2 — 590 76 2210 2.8 50 800
A 202_ 29.2 120 2200 4.4 — 640 60 2210 2.2 90 900
A 202_ 35.4 99 2210 3.6 — 710 49 2210 1.8 120 980
A 202_ 43.2 81 2210 3.0 — 780 41 2210 1.5 140 1080
A 202_ 53.7 65 2210 2.4 — 860 33 2210 1.2 150 1180
A 202_ 63.1 55 2170 2.0 — 940 27.7 2170 1.0 170 1280
A 202_ 79.9 44 1860 1.4 — 1100 21.9 1860 0.68 250 1390
A 202_ 92.3 38 1770 1.1 140 1180 19.0 1770 0.56 280 1390
A 203_ 120.5 29.0 1490 0.74 250 1370 14.5 1860 0.46 290 1390
A 203_ 146.1 24.0 1620 0.66 260 1390 12.0 2040 0.42 290 1390
A 203_ 178.3 19.6 1730 0.58 270 1390 9.8 2170 0.36 290 1390
A 203_ 221.3 15.8 1800 0.49 280 1390 7.9 2210 0.30 290 1390
A 203_ 260.5 13.4 1890 0.43 290 1390 6.7 2210 0.25 290 1390
A 203_ 329.4 10.6 1960 0.36 290 1390 5.3 2210 0.20 290 1390
A 203_ 380.9 9.2 2000 0.31 290 1390 4.6 2210 0.17 290 1390

A 20
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 202_ 5.4 204 1170 4.0 — 640 111 1420 2.6 — 780
A 202_ 7.3 151 1350 3.4 — 700 82 1640 2.2 — 850
A 202_ 9.4 117 1490 2.9 — 760 64 1810 1.9 — 920
A 202_ 10.3 107 1650 2.9 — 670 58 2210 2.1 140 890
A 202_ 12.0 92 2210 3.4 — 810 50 1860 1.6 — 1010
A 202_ 14.1 78 2210 2.9 70 780 43 2210 1.6 240 1030
A 202_ 18.1 61 2210 2.2 130 880 33 2210 1.2 300 1160
A 202_ 23.1 48 2210 1.8 160 990 26.0 2210 0.96 330 1280
A 202_ 29.2 38 2210 1.4 200 1100 20.5 2210 0.76 370 1390
A 202_ 35.4 31 2210 1.1 230 1200 16.9 2210 0.62 400 1390
A 202_ 43.2 25.5 2210 0.94 250 1300 13.9 2210 0.51 420 1390
A 202_ 53.7 20.5 2210 0.76 250 1390 11.2 2210 0.41 420 1390
A 202_ 63.1 17.4 2170 0.63 280 1390 9.5 2170 0.34 440 1390
A 202_ 79.9 13.8 1860 0.43 360 1390 7.5 1860 0.23 460 1390
A 202_ 92.3 11.9 1770 0.35 360 1390 6.5 1770 0.19 470 1390
A 203_ 120.5 9.1 2170 0.34 290 1390 5.0 2210 0.19 290 1390
A 203_ 146.1 7.5 2210 0.28 290 1390 4.1 2210 0.16 290 1390
A 203_ 178.3 6.2 2210 0.23 290 1390 3.4 2210 0.13 290 1390
A 203_ 221.3 5.0 2210 0.19 290 1390 2.7 2210 0.10 290 1390
A 203_ 260.5 4.2 2210 0.16 290 1390 2.3 2210 0.09 290 1390
A 203_ 329.4 3.3 2210 0.13 290 1390 1.8 2210 0.07 290 1390
A 203_ 380.9 2.9 2210 0.11 290 1390 1.6 2210 0.06 290 1390
(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

51
 A 30 3,630 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 302_ 5.4 648 1550 16.8 — 560 324 1950 10.5 — 700
A 302_ 7.0 500 1720 14.3 — 600 250 2170 9.1 — 760
A 302_ 9.3 376 1890 11.9 — 660 188 2390 7.5 — 830
A 302_ 10.5 333 2460 13.7 150 620 167 3010 8.4 220 800
A 302_ 11.8 297 2040 10.1 — 720 148 2570 6.4 — 910
A 302_ 13.6 257 2660 11.4 170 680 129 3270 7.0 240 870
A 302_ 18.0 194 2890 9.4 180 750 97 3540 5.7 260 960
A 302_ 22.8 154 3110 8.0 180 820 77 3630 4.6 300 1070
A 302_ 29.3 119 3350 6.7 180 890 60 3630 3.6 360 1210
A 302_ 36.6 96 3580 5.7 160 970 48 3630 2.9 400 1350
A 302_ 43.4 81 3630 4.9 170 1050 40 3630 2.4 420 1460
A 302_ 52.7 66 3630 4.0 190 1150 33 3630 2.0 430 1590
A 302_ 66.0 53 3450 3.1 250 1310 26.5 3450 1.5 450 1780
A 302_ 76.5 46 3100 2.4 330 1460 22.9 3100 1.2 470 1950
A 302_ 97.5 36 2660 1.6 360 1680 17.9 2660 0.80 490 2160
A 303_ 120.5 29.0 2150 1.1 250 1920 14.5 2660 0.66 290 2160
A 303_ 150.7 23.2 2310 0.92 260 2070 11.6 2920 0.58 290 2160
A 303_ 178.5 19.6 2420 0.81 270 2160 9.8 3050 0.51 290 2160
A 303_ 216.6 16.2 2540 0.70 280 2160 8.1 3190 0.44 290 2160
A 303_ 271.5 12.9 2660 0.59 290 2160 6.4 3360 0.37 290 2160
A 303_ 314.5 11.1 2730 0.52 290 2160 5.6 3450 0.33 290 2160
A 303_ 400.8 8.7 2830 0.42 290 2160 4.4 3190 0.24 290 2160

A 30
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 302_ 5.4 204 2260 7.7 — 820 111 2660 4.9 — 1000
A 302_ 7.0 157 2510 6.6 — 880 86 2660 3.8 190 1130
A 302_ 9.3 118 2660 5.2 — 980 65 2660 2.9 330 1280
A 302_ 10.5 105 3460 6.0 270 930 57 3630 3.5 490 1210
A 302_ 11.8 93 2660 4.1 120 1100 51 2660 2.3 420 1420
A 302_ 13.6 81 3630 4.9 330 1030 44 3630 2.7 490 1370
A 302_ 18.0 61 3630 3.7 430 1190 33 3630 2.0 490 1560
A 302_ 22.8 48 3630 2.9 490 1330 26.3 3630 1.6 490 1730
A 302_ 29.3 38 3630 2.3 490 1490 20.5 3630 1.2 490 1930
A 302_ 36.6 30 3630 1.8 490 1650 16.4 3630 0.99 490 2120
A 302_ 43.4 25.3 3630 1.5 490 1780 13.8 3630 0.84 490 2160
A 302_ 52.7 20.9 3630 1.3 490 1930 11.4 3630 0.69 490 2160
A 302_ 66.0 16.7 3450 0.96 490 2150 9.1 3450 0.52 490 2160
A 302_ 76.5 14.4 3100 0.74 490 2160 7.8 3100 0.41 490 2160
A 302_ 97.5 11.3 2660 0.50 490 2160 6.2 2660 0.27 490 2160
A 303_ 120.5 9.1 3130 0.49 290 2160 5.0 3630 0.31 290 2160
A 303_ 150.7 7.3 3370 0.42 290 2160 4.0 3630 0.25 290 2160
A 303_ 178.5 6.2 3540 0.37 290 2160 3.4 3630 0.21 290 2160
A 303_ 216.6 5.1 3630 0.32 290 2160 2.8 3630 0.17 290 2160
A 303_ 271.5 4.1 3630 0.25 290 2160 2.2 3630 0.14 290 2160
A 303_ 314.5 3.5 3630 0.22 290 2160 1.9 3630 0.12 290 2160
A 303_ 400.8 2.7 3190 0.15 290 2160 1.5 3190 0.08 290 2160
(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

52
 A 41 7,520 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 412_ 5.2 673 3980 45 — 980 337 4870 27 — 1250

A 412_ 7.1 493 4340 36 — 1090 246 4870 20 — 1450
A 412_ 9.2 380 4690 30 — 1190 190 4870 15.5 — 1630
A 412_ 10.1 347 3850 22 340 1360 173 4730 13.7 460 1720
A 412_ 11.7 299 4870 24 — 1320 150 4870 12.2 — 1810
A 412_ 13.8 254 4250 18.0 360 1500 127 5180 11.0 490 1910
A 412_ 17.8 197 4560 15.0 390 1640 98 5580 9.2 520 2090
A 412_ 22.7 154 4870 12.5 380 1790 77 6020 7.7 500 2270
A 412_ 28.3 124 5270 10.9 350 1930 62 6460 6.7 480 2450
A 412_ 35.9 97 5620 9.1 330 2100 49 6900 5.6 460 2650
A 412_ 45.1 78 6020 7.8 310 2270 39 7350 4.8 440 2880
A 412_ 53.1 66 6200 6.8 310 2410 33 7520 4.1 440 3080
A 412_ 64.2 55 6550 6.0 270 2590 27.3 7520 3.4 470 3330
A 412_ 79.2 44 7080 5.2 200 2770 22.1 7080 2.6 560 3370
A 413_ 92.8 38 5750 3.7 — 3150 18.9 7080 2.3 — 3370
A 413_ 115.9 30 7080 3.7 — 3280 15.1 7520 1.9 — 3370
A 413_ 146.9 23.8 7520 3.1 — 3370 11.9 7520 1.5 120 3370
A 413_ 184.4 19.0 7520 2.4 — 3370 9.5 7520 1.2 230 3370
A 413_ 217.4 16.1 7520 2.1 160 3370 8.0 7520 1.0 300 3370
A 413_ 262.5 13.3 7520 1.7 220 3370 6.7 7520 0.86 320 3370
A 413_ 324.2 10.8 7520 1.4 260 3370 5.4 7520 0.69 340 3370
A 413_ 376.8 9.3 7520 1.2 270 3370 4.6 7520 0.60 350 3370

A 41
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 412_ 5.2 212 4870 17.2 — 1540 115 4870 9.4 — 2000
A 412_ 7.1 155 4870 12.6 — 1770 85 4870 6.9 180 2270
A 412_ 9.2 120 4870 9.7 — 1980 65 4870 5.3 400 2540
A 412_ 10.1 109 5400 9.8 560 2010 59 6460 6.4 710 2450
A 412_ 11.7 94 4870 7.6 — 2190 51 4870 4.2 520 2790
A 412_ 13.8 80 5930 7.9 580 2230 43 7080 5.1 740 2720
A 412_ 17.8 62 6370 6.6 630 2430 34 7520 4.2 790 2990
A 412_ 22.7 48 6900 5.6 590 2630 26.4 7520 3.3 790 3330
A 412_ 28.3 39 7350 4.8 580 2860 21.2 7520 2.7 790 3370
A 412_ 35.9 31 7520 3.8 620 3150 16.7 7520 2.1 790 3370
A 412_ 45.1 24.4 7520 3.1 680 3370 13.3 7520 1.7 790 3370
A 412_ 53.1 20.7 7520 2.6 710 3370 11.3 7520 1.4 790 3370
A 412_ 64.2 17.1 7520 2.1 740 3370 9.3 7520 1.2 790 3370
A 412_ 79.2 13.9 7080 1.6 790 3370 7.6 7080 0.89 790 3370
A 413_ 92.8 11.9 7080 1.4 — 3370 6.5 7080 0.78 120 3370
A 413_ 115.9 9.5 7520 1.2 — 3370 5.2 7520 0.67 250 3370
A 413_ 146.9 7.5 7520 0.96 230 3370 4.1 7520 0.53 400 3370
A 413_ 184.4 6.0 7520 0.77 340 3370 3.3 7520 0.42 450 3370
A 413_ 217.4 5.1 7520 0.65 370 3370 2.8 7520 0.36 470 3370
A 413_ 262.5 4.2 7520 0.54 390 3370 2.3 7520 0.29 490 3370
A 413_ 324.2 3.4 7520 0.44 400 3370 1.9 7520 0.24 490 3370
A 413_ 376.8 2.9 7520 0.38 410 3370 1.6 7520 0.20 490 3370
(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

53
 A 50 13,300 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 502_ 7.7 455 4870 37 — 1780 227 6200 24 — 2240

A 502_ 9.7 361 5310 32 — 1920 180 6640 20 — 2430
A 502_ 13.1 267 5310 24 — 2160 134 6640 14.8 — 2720
A 502_ 16.6 211 5660 19.9 — 2340 105 7080 12.5 — 2940
A 502_ 20.9 167 5660 15.8 120 2560 84 7080 9.9 160 3240
A 503_ 24.0 146 10200 25 180 1580 73 13300 16.6 180 1920
A 503_ 26.4 133 10600 24 240 1610 66 13300 15.1 320 2050
A 503_ 32.4 108 11400 21 170 1040 54 13300 12.3 330 2340
A 503_ 35.6 98 11900 20 240 1760 49 13300 11.2 460 2470
A 503_ 40.9 86 12500 18.3 160 1830 43 13300 9.7 440 2680
A 503_ 45.0 78 13000 17.3 220 1870 39 13300 8.9 560 2830
A 503_ 51.7 68 13300 15.4 140 2020 34 13300 7.7 500 3060
A 503_ 56.8 62 13300 14.0 250 2140 31 13300 7.0 610 3240
A 503_ 63.9 55 13300 12.5 200 2320 27.4 13300 6.2 550 3440
A 503_ 70.2 50 13300 11.3 300 2450 24.9 13300 5.7 660 3620
A 503_ 81.5 43 13300 9.8 260 2680 21.5 13300 4.9 620 3890
A 503_ 89.5 39 13300 8.9 360 2830 19.6 13300 4.5 690 4090
A 503_ 99.5 35 13300 8.0 280 3010 17.6 13300 4.0 640 4320
A 503_ 109.4 32 13300 7.3 380 3170 16.0 13300 3.6 690 4500
A 503_ 118.0 29.7 13300 6.8 310 3300 14.8 13300 3.4 670 4500
A 503_ 129.7 27.0 13300 6.1 410 3460 13.5 13300 3.1 700 4500
A 503_ 140.6 24.9 13300 5.7 320 3620 12.4 13300 2.8 680 4500
A 503_ 154.6 22.6 13300 5.2 420 3800 11.3 13300 2.6 710 4500
A 503_ 173.4 20.2 13300 4.6 330 4020 10.1 13300 2.3 690 4500
A 503_ 190.6 18.4 13300 4.2 430 4230 9.2 13300 2.1 710 4500
A 504_ 211.0 16.6 13300 3.9 300 4500 8.3 13300 1.9 460 4500
A 504_ 232.0 15.1 13300 3.5 340 4500 7.5 13300 1.8 470 4500
A 504_ 260.9 13.4 13300 3.1 360 4500 6.7 13300 1.6 490 4500
A 504_ 286.8 12.2 13300 2.8 370 4500 6.1 13300 1.4 490 4500
A 504_ 332.6 10.5 13300 2.5 390 4500 5.3 13300 1.2 490 4500
A 504_ 365.6 9.6 13300 2.2 400 4500 4.8 13300 1.1 490 4500
A 504_ 406.4 8.6 13300 2.0 410 4500 4.3 13300 1.0 490 4500
A 504_ 446.8 7.8 13300 1.8 410 4500 3.9 13300 0.91 490 4500
A 504_ 481.6 7.3 13300 1.7 420 4500 3.6 13300 0.85 490 4500
A 504_ 529.5 6.6 13300 1.5 420 4500 3.3 13300 0.77 490 4500
A 504_ 574.2 6.1 13300 1.4 430 4500 3.0 13300 0.71 490 4500
A 504_ 631.2 5.5 13300 1.3 440 4500 2.8 13300 0.65 490 4500
A 504_ 707.9 4.9 13300 1.2 440 4500 2.5 13300 0.58 490 4500
A 504_ 778.2 4.5 13300 1.0 450 4500 2.2 13300 0.52 490 4500

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

54
 A 50 13,300 Ib·in
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 502_ 7.7 143 6810 16.2 — 2630 78 7970 10.4 — 3210

A 502_ 9.7 113 7350 13.9 — 2830 62 8850 9.1 — 3440
A 502_ 13.1 84 7350 10.3 160 3190 46 8850 6.8 210 3890
A 502_ 16.6 66 7790 8.6 200 3460 36 8850 5.3 390 4250
A 502_ 20.9 53 7790 6.8 280 3780 28.7 8850 4.2 480 4500
A 503_ 24.0 46 13300 10.4 450 2540 25.0 13300 5.7 790 3530
A 503_ 26.4 42 13300 9.5 590 2700 22.7 13300 5.2 790 3710
A 503_ 32.4 34 13300 7.7 610 3010 18.5 13300 4.2 790 4110
A 503_ 35.6 31 13300 7.0 740 3190 16.9 13300 3.8 790 4320
A 503_ 40.9 26.9 13300 6.1 720 3440 14.7 13300 3.3 790 4500
A 503_ 45.0 24.4 13300 5.6 790 3600 13.3 13300 3.0 790 4500
A 503_ 51.7 21.3 13300 4.8 780 3870 11.6 13300 2.6 790 4500
A 503_ 56.8 19.4 13300 4.4 790 4070 10.6 13300 2.4 790 4500
A 503_ 63.9 17.2 13300 3.9 790 4320 9.4 13300 2.1 790 4500
A 503_ 70.2 15.7 13300 3.6 790 4500 8.5 13300 1.9 790 4500
A 503_ 81.5 13.5 13300 3.1 790 4500 7.4 13300 1.7 790 4500
A 503_ 89.5 12.3 13300 2.8 790 4500 6.7 13300 1.5 790 4500
A 503_ 99.5 11.1 13300 2.5 790 4500 6.0 13300 1.4 790 4500
A 503_ 109.4 10.1 13300 2.3 790 4500 5.5 13300 1.2 790 4500
A 503_ 118.0 9.3 13300 2.1 790 4500 5.1 13300 1.2 790 4500
A 503_ 129.7 8.5 13300 1.9 790 4500 4.6 13300 1.1 790 4500
A 503_ 140.6 7.8 13300 1.8 790 4500 4.3 13300 0.97 790 4500
A 503_ 154.6 7.1 13300 1.6 790 4500 3.9 13300 0.88 790 4500
A 503_ 173.4 6.3 13300 1.4 790 4500 3.5 13300 0.79 790 4500
A 503_ 190.6 5.8 13300 1.3 790 4500 3.1 13300 0.72 790 4500
A 504_ 211.0 5.2 13300 1.2 490 4500 2.8 13300 0.66 490 4500
A 504_ 232.0 4.7 13300 1.1 490 4500 2.6 13300 0.60 490 4500
A 504_ 260.9 4.2 13300 0.98 490 4500 2.3 13300 0.54 490 4500
A 504_ 286.8 3.8 13300 0.90 490 4500 2.1 13300 0.49 490 4500
A 504_ 332.6 3.3 13300 0.77 490 4500 1.8 13300 0.42 490 4500
A 504_ 365.6 3.0 13300 0.70 490 4500 1.6 13300 0.38 490 4500
A 504_ 406.4 2.7 13300 0.63 490 4500 1.5 13300 0.34 490 4500
A 504_ 446.8 2.5 13300 0.57 490 4500 1.3 13300 0.31 490 4500
A 504_ 481.6 2.3 13300 0.53 490 4500 1.2 13300 0.29 490 4500
A 504_ 529.5 2.1 13300 0.48 490 4500 1.1 13300 0.26 490 4500
A 504_ 574.2 1.9 13300 0.45 490 4500 1.0 13300 0.24 490 4500
A 504_ 631.2 1.7 13300 0.41 490 4500 0.95 13300 0.22 490 4500
A 504_ 707.9 1.6 13300 0.36 490 4500 0.85 13300 0.20 490 4500
A 504_ 778.2 1.4 13300 0.33 490 4500 0.77 13300 0.18 490 4500

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

55
 A 60 24,800 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 602_ 7.9 443 8410 62 — 5060 222 10600 39 — 6230

A 602_ 10.3 340 8410 48 — 5530 170 10600 30 — 6740
A 602_ 12.7 276 8850 41 — 5890 138 11100 26 130 6740
A 602_ 16.7 210 9740 34 150 6430 105 11500 20 230 6740
A 602_ 20.6 170 24400 69 160 6740 85 12400 17.6 180 6740
A 603_ 25.7 136 24800 58 — 6050 68 24800 29 130 6740
A 603_ 27.9 125 24800 53 — 6230 63 24800 27 320 6740
A 603_ 31.7 110 24800 47 — 6520 55 24800 23 310 6740
A 603_ 34.3 102 24800 43 — 6740 51 24800 22 490 6740
A 603_ 41.7 84 24800 36 — 6740 42 24800 17.8 490 6740
A 603_ 45.2 77 24800 33 110 6740 39 24800 16.4 650 6740
A 603_ 51.3 68 24800 29 — 6740 34 24800 14.5 600 6740
A 603_ 55.6 63 24800 27 210 6740 31 24800 13.4 750 6740
A 603_ 65.0 54 24800 23 160 6740 26.9 24800 11.4 690 6740
A 603_ 70.4 50 24800 21 300 6740 24.9 24800 10.6 840 6740
A 603_ 79.7 44 24800 18.6 220 6740 22.0 24800 9.3 760 6740
A 603_ 86.4 41 24800 17.2 360 6740 20.3 24800 8.6 900 6740
A 603_ 99.5 35 24800 14.9 280 6740 17.6 24800 7.5 820 6740
A 603_ 107.8 32 24800 13.8 420 6740 16.2 24800 6.9 910 6740
A 603_ 123.0 28.5 24800 12.1 340 6740 14.2 24800 6.0 880 6740
A 603_ 133.3 26.3 24800 11.1 470 6740 13.1 24800 5.6 920 6740
A 603_ 144.0 24.3 24800 10.3 360 6740 12.2 24800 5.2 900 6740
A 603_ 156.0 22.4 24800 9.5 500 6740 11.2 24800 4.8 930 6740
A 603_ 171.5 20.4 24800 8.7 380 6740 10.2 24800 4.3 910 6740
A 603_ 185.8 18.8 24800 8.0 510 6740 9.4 24800 4.0 930 6740
A 604_ 208.7 16.8 24800 7.3 400 6740 8.4 24800 3.6 700 6740
A 604_ 226.1 15.5 24800 6.7 470 6740 7.7 24800 3.4 720 6740
A 604_ 264.3 13.2 24800 5.8 560 6740 6.6 24800 2.9 750 6740
A 604_ 286.3 12.2 24800 5.3 570 6740 6.1 24800 2.7 760 6740
A 604_ 324.2 10.8 24800 4.7 590 6740 5.4 24800 2.3 780 6740
A 604_ 351.2 10.0 24800 4.3 600 6740 5.0 24800 2.2 790 6740
A 604_ 404.7 8.6 24800 3.8 620 6740 4.3 24800 1.9 790 6740
A 604_ 438.4 8.0 24800 3.5 620 6740 4.0 24800 1.7 790 6740
A 604_ 500.3 7.0 24800 3.0 640 6740 3.5 24800 1.5 790 6740
A 604_ 542.0 6.5 24800 2.8 640 6740 3.2 24800 1.4 790 6740
A 604_ 585.8 6.0 24800 2.6 650 6740 3.0 24800 1.3 790 6740
A 604_ 634.6 5.5 24800 2.4 660 6740 2.8 24800 1.2 790 6740
A 604_ 697.3 5.0 24800 2.2 660 6740 2.5 24800 1.1 790 6740
A 604_ 755.4 4.6 24800 2.0 670 6740 2.3 24800 1.0 790 6740

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

56
 A 60 24,800 Ib·in
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 602_ 7.9 139 11500 27 — 6740 76 13700 17.4 — 6740

A 602_ 10.3 107 11500 20 250 6740 58 13700 13.3 370 6740
A 602_ 12.7 87 12400 17.9 250 6740 47 15000 11.8 310 6740
A 602_ 16.7 66 12800 14.1 380 6740 36 15000 9.0 570 6740
A 602_ 20.6 53 13700 12.2 330 6740 29.1 15900 7.7 560 6740
A 603_ 25.7 43 24800 18.2 550 6740 23.3 24800 9.9 1060 6740
A 603_ 27.9 39 24800 16.7 740 6740 21.5 24800 9.1 1060 6740
A 603_ 31.7 35 24800 14.7 720 6740 18.9 24800 8.0 1060 6740
A 603_ 34.3 32 24800 13.6 900 6740 17.5 24800 7.4 1060 6740
A 603_ 41.7 26.4 24800 11.2 910 6740 14.4 24800 6.1 1060 6740
A 603_ 45.2 24.3 24800 10.3 1040 6740 13.3 24800 5.6 1060 6740
A 603_ 51.3 21.4 24800 9.1 1010 6740 11.7 24800 5.0 1060 6740
A 603_ 55.6 19.8 24800 8.4 1060 6740 10.8 24800 4.6 1060 6740
A 603_ 65.0 16.9 24800 7.2 1050 6740 9.2 24800 3.9 1060 6740
A 603_ 70.4 15.6 24800 6.6 1060 6740 8.5 24800 3.6 1060 6740
A 603_ 79.7 13.8 24800 5.9 1060 6740 7.5 24800 3.2 1060 6740
A 603_ 86.4 12.7 24800 5.4 1060 6740 6.9 24800 2.9 1060 6740
A 603_ 99.5 11.1 24800 4.7 1060 6740 6.0 24800 2.6 1060 6740
A 603_ 107.8 10.2 24800 4.3 1060 6740 5.6 24800 2.4 1060 6740
A 603_ 123.0 8.9 24800 3.8 1060 6740 4.9 24800 2.1 1060 6740
A 603_ 133.3 8.3 24800 3.5 1060 6740 4.5 24800 1.9 1060 6740
A 603_ 144.0 7.6 24800 3.2 1060 6740 4.2 24800 1.8 1060 6740
A 603_ 156.0 7.1 24800 3.0 1060 6740 3.8 24800 1.6 1060 6740
A 603_ 171.5 6.4 24800 2.7 1060 6740 3.5 24800 1.5 1060 6740
A 603_ 185.8 5.9 24800 2.5 1060 6740 3.2 24800 1.4 1060 6740
A 604_ 208.7 5.3 24800 2.3 790 6740 2.9 24800 1.3 790 6740
A 604_ 226.1 4.9 24800 2.1 790 6740 2.7 24800 1.2 790 6740
A 604_ 264.3 4.2 24800 1.8 790 6740 2.3 24800 0.99 790 6740
A 604_ 286.3 3.8 24800 1.7 790 6740 2.1 24800 0.91 790 6740
A 604_ 324.2 3.4 24800 1.5 790 6740 1.9 24800 0.81 790 6740
A 604_ 351.2 3.1 24800 1.4 790 6740 1.7 24800 0.74 790 6740
A 604_ 404.7 2.7 24800 1.2 790 6740 1.5 24800 0.65 790 6740
A 604_ 438.4 2.5 24800 1.1 790 6740 1.4 24800 0.60 790 6740
A 604_ 500.3 2.2 24800 0.96 790 6740 1.2 24800 0.52 790 6740
A 604_ 542.0 2.0 24800 0.88 790 6740 1.1 24800 0.48 790 6740
A 604_ 585.8 1.9 24800 0.82 790 6740 1.0 24800 0.45 790 6740
A 604_ 634.6 1.7 24800 0.75 790 6740 0.95 24800 0.41 790 6740
A 604_ 697.3 1.6 24800 0.69 790 6740 0.86 24800 0.37 790 6740
A 604_ 755.4 1.5 24800 0.63 790 6740 0.79 24800 0.35 790 6740

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

57
 A 70 44,300 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 703_ 9.4 372 20400 130 430 5820 186 24800 79 570 7170
A 703_ 10.2 343 21200 125 560 5930 172 28300 83 330 7170
A 703_ 12.1 289 21200 105 540 6290 145 28300 70 310 7620
A 703_ 13.1 267 23000 105 540 6380 134 29600 68 470 7780
A 703_ 15.4 227 23900 93 470 6720 114 29600 58 550 8250
A 703_ 16.7 210 25200 90 560 6830 105 31900 57 580 8360
A 703_ 19.7 178 25700 78 460 7220 89 32700 50 400 8830
A 703_ 21.3 164 26600 75 620 7400 82 35400 50 410 8950
A 703_ 23.5 149 31000 79 1110 7400 74 38100 49 1410 9100
A 703_ 27.8 126 30500 66 1120 7890 63 37200 40 1420 9730
A 703_ 30.1 116 32700 65 1120 8000 58 40300 40 1420 9870
A 703_ 35.4 99 32300 55 1130 8520 49 39800 34 1430 10500
A 703_ 38.4 91 35000 55 1130 8630 46 42900 33 1430 10600
A 703_ 45.2 77 34500 46 1140 9170 39 42500 28 1440 11200
A 703_ 49.0 71 37600 46 1140 9280 36 44300 27 1450 11200
A 703_ 53.2 66 36300 41 1130 9640 33 44300 25 1430 11200
A 703_ 57.7 61 39400 41 1130 9760 30 44300 23 1460 11200
A 703_ 66.9 52 38500 34 1140 10300 26.2 44300 19.8 1460 11200
A 703_ 72.5 48 42000 35 1130 10500 24.1 44300 18.3 1480 11200
A 703_ 79.3 44 40700 31 1130 10900 22.1 44300 16.7 1470 11200
A 703_ 85.9 41 43800 31 1130 11000 20.4 44300 15.4 1490 11200
A 703_ 96.2 36 42900 27 1120 11200 18.2 44300 13.8 1480 11200
A 703_ 104.2 34 44300 25 1140 11200 16.8 44300 12.7 1500 11200
A 703_ 120.6 29.0 44300 22 1130 11200 14.5 44300 11.0 1490 11200
A 703_ 130.7 26.8 44300 20 1150 11200 13.4 44300 10.2 1500 11200
A 703_ 141.9 24.7 44300 18.7 1130 11200 12.3 44300 9.4 1490 11200
A 703_ 153.7 22.8 29200 11.4 1220 11200 11.4 35800 7.0 1560 11200
A 704_ 169.8 20.6 44300 16.0 250 11200 10.3 44300 8.0 570 11200
A 704_ 183.9 19.0 44300 14.8 330 11200 9.5 44300 7.4 600 11200
A 704_ 220.3 15.9 44300 12.4 350 11200 7.9 44300 6.2 610 11200
A 704_ 238.6 14.7 44300 11.4 420 11200 7.3 44300 5.7 620 11200
A 704_ 292.0 12.0 44300 9.3 430 11200 6.0 44300 4.7 630 11200
A 704_ 316.4 11.1 44300 8.6 470 11200 5.5 44300 4.3 640 11200
A 704_ 369.4 9.5 44300 7.4 470 11200 4.7 44300 3.7 640 11200
A 704_ 400.2 8.7 44300 6.8 490 11200 4.4 44300 3.4 650 11200
A 704_ 475.8 7.4 44300 5.7 480 11200 3.7 44300 2.9 650 11200
A 704_ 515.4 6.8 44300 5.3 490 11200 3.4 44300 2.6 660 11200
A 704_ 595.0 5.9 44300 4.6 490 11200 2.9 44300 2.3 660 11200
A 704_ 644.6 5.4 44300 4.2 500 11200 2.7 44300 2.1 670 11200
A 704_ 705.1 5.0 44300 3.9 490 11200 2.5 44300 1.9 660 11200
A 704_ 763.9 4.6 44300 3.6 510 11200 2.3 44300 1.8 670 11200
A 704_ 855.3 4.1 44300 3.2 500 11200 2.0 44300 1.6 670 11200
A 704_ 926.5 3.8 44300 2.9 510 11200 1.9 44300 1.5 670 11200
A 704_ 1072 3.3 44300 2.5 500 11200 1.6 44300 1.3 670 11200
A 704_ 1161 3.0 44300 2.3 510 11200 1.5 44300 1.2 680 11200
A 704_ 1242 2.8 44300 2.2 510 11200 1.4 44300 1.1 670 11200
A 704_ 1346 2.6 44300 2.0 510 11200 1.3 44300 1.0 680 11200
A 704_ 1583 2.2 44300 1.7 510 11200 1.1 44300 0.86 670 11200
A 704_ 1715 2.0 44300 1.6 520 11200 1.0 44300 0.79 680 11200

58
 A 70 44,300 Ib·in
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 703_ 9.4 117 26600 53 960 8300 64 26600 29 1570 10200

A 703_ 10.2 108 28800 53 960 8410 59 28800 29 1570 10400
A 703_ 12.1 91 32300 50 360 8700 50 32300 27 1450 10800
A 703_ 13.1 84 35000 50 370 8810 46 35000 27 1460 10900
A 703_ 15.4 71 32700 40 790 9490 39 32700 22 1570 11200
A 703_ 16.7 66 35400 40 800 9620 36 35400 22 1570 11200
A 703_ 19.7 56 32700 31 1100 10400 30 32700 17.0 1570 11200
A 703_ 21.3 52 35400 31 1110 10500 28.2 35400 17.1 1570 11200
A 703_ 23.5 47 43400 35 1570 10400 25.5 44300 19.4 1570 11200
A 703_ 27.8 40 42500 29 1570 11100 21.6 44300 16.4 1570 11200
A 703_ 30.1 37 44300 28 1570 11200 19.9 44300 15.1 1570 11200
A 703_ 35.4 31 44300 24 1570 11200 16.9 44300 12.9 1570 11200
A 703_ 38.4 28.6 44300 22 1570 11200 15.6 44300 11.8 1570 11200
A 703_ 45.2 24.3 44300 18.5 1570 11200 13.3 44300 10.1 1570 11200
A 703_ 49.0 22.4 44300 17.0 1570 11200 12.2 44300 9.3 1570 11200
A 703_ 53.2 20.7 44300 15.7 1570 11200 11.3 44300 8.6 1570 11200
A 703_ 57.7 19.1 44300 14.5 1570 11200 10.4 44300 7.9 1570 11200
A 703_ 66.9 16.4 44300 12.5 1570 11200 9.0 44300 6.8 1570 11200
A 703_ 72.5 15.2 44300 11.5 1570 11200 8.3 44300 6.3 1570 11200
A 703_ 79.3 13.9 44300 10.5 1570 11200 7.6 44300 5.7 1570 11200
A 703_ 85.9 12.8 44300 9.7 1570 11200 7.0 44300 5.3 1570 11200
A 703_ 96.2 11.4 44300 8.7 1570 11200 6.2 44300 4.7 1570 11200
A 703_ 104.2 10.6 44300 8.0 1570 11200 5.8 44300 4.4 1570 11200
A 703_ 120.6 9.1 44300 6.9 1570 11200 5.0 44300 3.8 1570 11200
A 703_ 130.7 8.4 44300 6.4 1570 11200 4.6 44300 3.5 1570 11200
A 703_ 141.9 7.8 44300 5.9 1570 11200 4.2 44300 3.2 1570 11200
A 703_ 153.7 7.2 40700 5.0 1570 11200 3.9 44300 3.0 1570 11200
A 704_ 169.8 6.5 44300 5.0 710 11200 3.5 44300 2.7 790 11200
A 704_ 183.9 6.0 44300 4.7 730 11200 3.3 44300 2.5 790 11200
A 704_ 220.3 5.0 44300 3.9 740 11200 2.7 44300 2.1 790 11200
A 704_ 238.6 4.6 44300 3.6 750 11200 2.5 44300 2.0 790 11200
A 704_ 292.0 3.8 44300 2.9 750 11200 2.1 44300 1.6 790 11200
A 704_ 316.4 3.5 44300 2.7 770 11200 1.9 44300 1.5 790 11200
A 704_ 369.4 3.0 44300 2.3 770 11200 1.6 44300 1.3 790 11200
A 704_ 400.2 2.7 44300 2.1 780 11200 1.5 44300 1.2 790 11200
A 704_ 475.8 2.3 44300 1.8 780 11200 1.3 44300 0.98 790 11200
A 704_ 515.4 2.1 44300 1.7 790 11200 1.2 44300 0.91 790 11200
A 704_ 595.0 1.8 44300 1.4 780 11200 1.0 44300 0.78 790 11200
A 704_ 644.6 1.7 44300 1.3 790 11200 0.93 44300 0.72 790 11200
A 704_ 705.1 1.6 44300 1.2 790 11200 0.85 44300 0.66 790 11200
A 704_ 763.9 1.4 44300 1.1 790 11200 0.79 44300 0.61 790 11200
A 704_ 855.3 1.3 44300 1.0 790 11200 0.70 44300 0.55 790 11200
A 704_ 926.5 1.2 44300 0.92 790 11200 0.65 44300 0.50 790 11200
A 704_ 1072 1.0 44300 0.80 790 11200 0.56 44300 0.44 790 11200
A 704_ 1161 0.95 44300 0.74 790 11200 0.52 44300 0.40 790 11200
A 704_ 1242 0.89 44300 0.69 790 11200 0.48 44300 0.38 790 11200
A 704_ 1346 0.82 44300 0.64 790 11200 0.45 44300 0.35 790 11200
A 704_ 1583 0.69 44300 0.54 790 11200 0.38 44300 0.29 790 11200
A 704_ 1715 0.64 44300 0.50 790 11200 0.35 44300 0.27 790 11200

59
 A 80 70,800 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 803_ 9.8 357 27400 167 — 5910 179 34500 105 — 7220
A 803_ 10.7 327 30500 171 — 5910 164 38100 107 — 7260
A 803_ 12.3 285 30500 149 — 6230 142 38100 93 — 7640
A 803_ 13.3 263 30500 137 260 6450 132 38100 86 260 7910
A 803_ 15.5 226 29200 113 350 6880 113 36300 70 390 8450
A 803_ 16.7 210 31900 114 320 6950 105 39800 71 330 8520
A 803_ 19.3 181 31000 96 420 7370 91 38900 60 420 9040
A 803_ 20.9 167 34000 97 380 7440 84 42500 61 390 9130
A 803_ 22.6 155 44700 118 1010 7010 77 55300 73 1310 8630
A 803_ 24.5 143 48700 119 1000 7040 71 59700 73 1310 8680
A 803_ 28.2 124 47300 100 1060 7530 62 58400 62 1340 9260
A 803_ 30.6 114 46500 91 1090 7850 57 57100 56 1380 9670
A 803_ 35.5 99 50400 85 1060 8090 49 62000 52 1350 9960
A 803_ 38.5 91 54400 85 1060 8140 45 67300 52 1350 10000
A 803_ 44.5 79 53500 72 1080 8680 39 65900 44 1360 10700
A 803_ 48.2 73 58000 72 1080 8720 36 70800 44 1370 10800
A 803_ 55.2 63 56600 61 1060 9280 32 69900 38 1360 11400
A 803_ 59.8 59 61500 62 1050 9330 29.3 70800 35 1390 11800
A 803_ 66.8 52 60200 54 1050 9820 26.2 70800 32 1380 12300
A 803_ 72.4 48 65000 54 1050 9890 24.2 70800 29 1410 12700
A 803_ 82.3 43 63700 46 1030 10500 21.3 70800 26 1400 13300
A 803_ 89.2 39 69000 46 1030 10500 19.6 70800 24 1430 13800
A 803_ 96.0 36 66400 41 990 11000 18.2 70800 22 1410 14200
A 803_ 104.0 34 70800 41 1010 11100 16.8 70800 20 1430 14600
A 803_ 116.0 30 70400 36 950 11600 15.1 70800 18.3 1420 14600
A 803_ 125.6 27.9 70800 34 1040 12000 13.9 70800 16.9 1440 14600
A 803_ 144.7 24.2 70800 29 970 12700 12.1 70800 14.7 1430 14600
A 803_ 156.8 22.3 70800 27 1070 13100 11.2 70800 13.5 1450 14600
A 804_ 171.3 20.4 70800 25 — 14600 10.2 70800 12.7 280 14600
A 804_ 214.7 16.3 70800 20 — 14600 8.2 70800 10.1 310 14600
A 804_ 232.6 15.0 70800 18.7 — 14600 7.5 70800 9.3 410 14600
A 804_ 277.3 12.6 70800 15.7 120 14600 6.3 70800 7.8 430 14600
A 804_ 300.4 11.7 70800 14.5 200 14600 5.8 70800 7.2 510 14600
A 804_ 354.0 9.9 70800 12.3 180 14600 4.9 70800 6.1 490 14600
A 804_ 383.5 9.1 70800 11.3 260 14600 4.6 70800 5.7 570 14600
A 804_ 442.1 7.9 70800 9.8 230 14600 4.0 70800 4.9 550 14600
A 804_ 478.9 7.3 70800 9.1 310 14600 3.7 70800 4.5 600 14600
A 804_ 560.5 6.2 70800 7.8 280 14600 3.1 70800 3.9 590 14600
A 804_ 607.2 5.8 70800 7.2 350 14600 2.9 70800 3.6 610 14600
A 804_ 703.5 5.0 70800 6.2 320 14600 2.5 70800 3.1 600 14600
A 804_ 762.1 4.6 70800 5.7 390 14600 2.3 70800 2.9 620 14600
A 804_ 829.5 4.2 70800 5.2 340 14600 2.1 70800 2.6 610 14600
A 804_ 898.7 3.9 70800 4.8 410 14600 1.9 70800 2.4 620 14600
A 804_ 1001 3.5 70800 4.3 360 14600 1.7 70800 2.2 620 14600
A 804_ 1085 3.2 70800 4.0 430 14600 1.6 70800 2.0 630 14600
A 804_ 1237 2.8 70800 3.5 370 14600 1.4 70800 1.8 620 14600
A 804_ 1340 2.6 70800 3.2 440 14600 1.3 70800 1.6 630 14600
A 804_ 1438 2.4 70800 3.0 390 14600 1.2 70800 1.5 620 14600
A 804_ 1558 2.2 70800 2.8 450 14600 1.1 70800 1.4 640 14600

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

60
 A 80 70,800 Ib·in
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 803_ 9.8 112 39400 76 — 8250 61 46900 49 — 9800

A 803_ 10.7 103 43400 76 — 8300 56 51800 50 — 9900
A 803_ 12.3 89 43400 66 — 8750 49 51800 43 — 10400
A 803_ 13.3 83 43400 61 310 9040 45 51800 40 360 10800
A 803_ 15.5 71 41200 50 480 9670 39 49100 33 570 11500
A 803_ 16.7 66 45100 51 410 9760 36 54000 33 480 11600
A 803_ 19.3 57 44300 43 510 10300 31 53100 28 570 12300
A 803_ 20.9 53 48400 44 460 10400 28.7 57500 28 570 12500
A 803_ 22.6 49 62800 52 1530 9870 26.5 70800 32 1570 12000
A 803_ 24.5 45 68100 52 1530 9910 24.5 70800 30 1570 12400
A 803_ 28.2 39 66800 45 1560 10600 21.3 70800 26 1570 13100
A 803_ 30.6 36 65500 40 1570 11000 19.6 70800 24 1570 13600
A 803_ 35.5 31 70800 38 1570 11400 16.9 70800 20 1570 14400
A 803_ 38.5 28.6 70800 35 1570 11800 15.6 70800 18.9 1570 14600
A 803_ 44.5 24.7 70800 30 1570 12500 13.5 70800 16.3 1570 14600
A 803_ 48.2 22.8 70800 28 1570 12900 12.4 70800 15.1 1570 14600
A 803_ 55.2 19.9 70800 24 1570 13600 10.9 70800 13.2 1570 14600
A 803_ 59.8 18.4 70800 22 1570 14000 10.0 70800 12.2 1570 14600
A 803_ 66.8 16.5 70800 20 1570 14600 9.0 70800 10.9 1570 14600
A 803_ 72.4 15.2 70800 18.4 1570 14600 8.3 70800 10.0 1570 14600
A 803_ 82.3 13.4 70800 16.2 1570 14600 7.3 70800 8.8 1570 14600
A 803_ 89.2 12.3 70800 14.9 1570 14600 6.7 70800 8.2 1570 14600
A 803_ 96.0 11.5 70800 13.9 1570 14600 6.3 70800 7.6 1570 14600
A 803_ 104.0 10.6 70800 12.8 1570 14600 5.8 70800 7.0 1570 14600
A 803_ 116.0 9.5 70800 11.5 1570 14600 5.2 70800 6.3 1570 14600
A 803_ 125.6 8.8 70800 10.6 1570 14600 4.8 70800 5.8 1570 14600
A 803_ 144.7 7.6 70800 9.2 1570 14600 4.1 70800 5.0 1570 14600
A 803_ 156.8 7.0 70800 8.5 1570 14600 3.8 70800 4.6 1570 14600
A 804_ 171.3 6.4 70800 8.0 520 14600 3.5 70800 4.4 790 14600
A 804_ 214.7 5.1 70800 6.4 560 14600 2.8 70800 3.5 790 14600
A 804_ 232.6 4.7 70800 5.9 650 14600 2.6 70800 3.2 790 14600
A 804_ 277.3 4.0 70800 4.9 670 14600 2.2 70800 2.7 790 14600
A 804_ 300.4 3.7 70800 4.5 700 14600 2.0 70800 2.5 790 14600
A 804_ 354.0 3.1 70800 3.9 700 14600 1.7 70800 2.1 790 14600
A 804_ 383.5 2.9 70800 3.6 710 14600 1.6 70800 1.9 790 14600
A 804_ 442.1 2.5 70800 3.1 710 14600 1.4 70800 1.7 790 14600
A 804_ 478.9 2.3 70800 2.9 730 14600 1.3 70800 1.6 790 14600
A 804_ 560.5 2.0 70800 2.4 720 14600 1.1 70800 1.3 790 14600
A 804_ 607.2 1.8 70800 2.3 740 14600 0.99 70800 1.2 790 14600
A 804_ 703.5 1.6 70800 1.9 730 14600 0.85 70800 1.1 790 14600
A 804_ 762.1 1.4 70800 1.8 750 14600 0.79 70800 0.98 790 14600
A 804_ 829.5 1.3 70800 1.6 740 14600 0.72 70800 0.90 790 14600
A 804_ 898.7 1.2 70800 1.5 750 14600 0.67 70800 0.83 790 14600
A 804_ 1001 1.1 70800 1.4 740 14600 0.60 70800 0.74 790 14600
A 804_ 1085 1.0 70800 1.3 760 14600 0.55 70800 0.69 790 14600
A 804_ 1237 0.89 70800 1.1 740 14600 0.49 70800 0.60 790 14600
A 804_ 1340 0.82 70800 1.0 760 14600 0.45 70800 0.56 790 14600
A 804_ 1438 0.76 70800 0.95 750 14600 0.42 70800 0.52 790 14600
A 804_ 1558 0.71 70800 0.88 760 14600 0.39 70800 0.48 790 14600

(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

61
 A 90 123,900 Ib·in
i n1 = 3500 rpm n1 = 1750 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 903_ 9.7 361 69000 426 550 6200 180 80100 247 1240 7870
A 903_ 10.5 333 73900 422 590 6230 167 86700 247 1240 7850
A 903_ 12.6 278 75200 358 610 6700 139 92500 220 1080 8250
A 903_ 13.7 255 71200 311 1050 7150 128 98700 216 1140 8300
A 903_ 15.6 224 78800 303 730 7190 112 96900 186 1220 8860
A 903_ 16.9 207 85400 303 730 7170 104 104900 186 1220 8830
A 903_ 19.4 180 83200 257 710 7710 90 102200 158 1200 9510
A 903_ 21.0 167 89800 256 720 7710 83 109700 156 1240 9530
A 903_ 22.3 157 87200 234 2170 8030 78 107500 144 2740 9870
A 903_ 24.1 145 94700 235 2170 7980 73 116400 145 2740 9850
A 903_ 29.1 120 93400 192 2200 8750 60 115100 118 2790 10800
A 903_ 31.5 111 101300 193 2200 8720 56 123900 118 2790 10800
A 903_ 35.8 98 98700 165 2230 9350 49 121700 102 2810 11500
A 903_ 38.8 90 107100 165 2230 9330 45 123900 96 2860 11800
A 903_ 44.6 78 104400 140 2230 10000 39 123900 83 2860 12600
A 903_ 48.3 72 113300 141 2230 10000 36 123900 77 2880 13000
A 903_ 55.0 64 111100 121 2240 10700 32 123900 67 2880 13800
A 903_ 59.6 59 119900 121 2240 10700 29.4 123900 62 2920 14300
A 903_ 68.8 51 118100 103 2240 11400 25.4 123900 54 2920 15200
A 903_ 74.5 47 123900 100 2250 11600 23.5 123900 50 2940 15700
A 903_ 80.4 44 123000 92 2230 12000 21.8 123900 46 2920 16200
A 903_ 87.1 40 123900 85 2270 12500 20.1 123900 43 2970 16700
A 903_ 98.6 35 123900 75 2250 13200 17.7 123900 38 2940 16900
A 903_ 106.8 33 123900 69 2270 13600 16.4 123900 35 2990 16900
A 903_ 116.9 29.9 123900 63 2270 14200 15.0 123900 32 2970 16900
A 903_ 126.6 27.6 94300 45 2380 16100 13.8 116400 28 3010 16900
A 903_ 139.4 25.1 91600 39 2380 16700 12.6 112800 24 3010 16900
A 903_ 151.0 23.2 99100 39 2380 16900 11.6 122100 24 3010 16900
A 904_ 166.1 21.1 123900 46 — 16900 10.5 123900 23 — 16900
A 904_ 180.0 19.4 123900 42 — 16900 9.7 123900 21 — 16900
A 904_ 209.0 16.7 123900 36 — 16900 8.4 123900 18.2 — 16900
A 904_ 226.4 15.5 123900 34 — 16900 7.7 123900 16.8 — 16900
A 904_ 281.4 12.4 123900 27 — 16900 6.2 123900 13.5 — 16900
A 904_ 304.9 11.5 123900 25 — 16900 5.7 123900 12.5 — 16900
A 904_ 355.8 9.8 123900 21 — 16900 4.9 123900 10.7 — 16900
A 904_ 385.4 9.1 123900 19.7 — 16900 4.5 123900 9.9 150 16900
A 904_ 449.2 7.8 123900 16.9 — 16900 3.9 123900 8.5 — 16900
A 904_ 486.6 7.2 123900 15.6 — 16900 3.6 123900 7.8 210 16900
A 904_ 555.3 6.3 123900 13.7 — 16900 3.2 123900 6.9 170 16900
A 904_ 601.6 5.8 123900 12.7 — 16900 2.9 123900 6.3 270 16900
A 904_ 707.9 4.9 123900 10.8 — 16900 2.5 123900 5.4 240 16900
A 904_ 766.9 4.6 123900 9.9 — 16900 2.3 123900 5.0 330 16900
A 904_ 865.1 4.0 123900 8.8 — 16900 2.0 123900 4.4 260 16900
A 904_ 937 3.7 123900 8.1 — 16900 1.9 123900 4.1 360 16900
A 904_ 1025 3.4 123900 7.4 — 16900 1.7 123900 3.7 300 16900
A 904_ 1111 3.2 123900 6.9 — 16900 1.6 123900 3.4 390 16900
A 904_ 1222 2.9 123900 6.2 — 16900 1.4 123900 3.1 310 16900
A 904_ 1324 2.6 123900 5.7 — 16900 1.3 123900 2.9 400 16900
A 904_ 1507 2.3 123900 5.1 — 16900 1.2 123900 2.5 320 16900
A 904_ 1632 2.1 123900 4.7 — 16900 1.1 123900 2.3 410 16900
(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

62
 A 90 123,900 Ib·in
i n1 = 1100 rpm n1 = 600 rpm

n2 Tn2 Pn1 Rn1 Rn2 n2 Tn2 Pn1 Rn1 Rn2

(ratio)
[rpm] [Ib·in] [hp] [Ib] [Ib] [rpm] [Ib·in] [hp] [Ib] [Ib]

A 903_ 9.7 113 80100 155 2200 9510 62 80100 85 3370 12100
A 903_ 10.5 105 86700 155 200 9550 57 86700 85 3370 12200
A 903_ 12.6 87 104400 156 1510 9460 48 104400 85 3030 12300
A 903_ 13.7 80 112800 155 1520 9460 44 113300 85 3030 12300
A 903_ 15.6 71 102200 123 1960 10500 38 102200 67 3370 13500
A 903_ 16.9 65 110600 123 1970 10500 36 110600 67 3370 13600
A 903_ 19.4 57 102200 99 2160 11600 31 102200 54 3370 14700
A 903_ 21.0 52 109700 98 2200 11600 28.6 109700 54 3370 14900
A 903_ 22.3 49 122600 104 3190 11300 26.9 123900 57 3370 14500
A 903_ 24.1 46 123900 97 3240 11700 24.9 123900 53 3370 15000
A 903_ 29.1 38 123900 80 3280 12600 20.6 123900 44 3370 16200
A 903_ 31.5 35 123900 74 3330 13100 19.0 123900 40 3370 16800
A 903_ 35.8 31 123900 65 3350 13900 16.8 123900 36 3370 16900
A 903_ 38.8 28.4 123900 60 3370 14400 15.5 123900 33 3370 16900
A 903_ 44.6 24.7 123900 52 3370 15200 13.5 123900 29 3370 16900
A 903_ 48.3 22.8 123900 48 3370 15700 12.4 123900 26 3370 16900
A 903_ 55.0 20.0 123900 42 3370 16600 10.9 123900 23 3370 16900
A 903_ 59.6 18.5 123900 39 3370 16900 10.1 123900 21 3370 16900
A 903_ 68.8 16.0 123900 34 3370 16900 8.7 123900 18.5 3370 16900
A 903_ 74.5 14.8 123900 31 3370 16900 8.1 123900 17.1 3370 16900
A 903_ 80.4 13.7 123900 29 3370 16900 7.5 123900 15.8 3370 16900
A 903_ 87.1 12.6 123900 27 3370 16900 6.9 123900 14.6 3370 16900
A 903_ 98.6 11.2 123900 24 3370 16900 6.1 123900 12.9 3370 16900
A 903_ 106.8 10.3 123900 22 3370 16900 5.6 123900 11.9 3370 16900
A 903_ 116.9 9.4 123900 20 3370 16900 5.1 123900 10.9 3370 16900
A 903_ 126.6 8.7 123900 18.4 3370 16900 4.7 123900 10.0 3370 16900
A 903_ 139.4 7.9 123900 16.7 3370 16900 4.3 123900 9.1 3370 16900
A 903_ 151.0 7.3 123900 15.4 3370 16900 4.0 123900 8.4 3370 16900
A 904_ 166.1 6.6 123900 14.4 — 16900 3.6 123900 7.9 160 16900
A 904_ 180.0 6.1 123900 13.3 — 16900 3.3 123900 7.2 310 16900
A 904_ 209.0 5.3 123900 11.4 — 16900 2.9 123900 6.2 340 16900
A 904_ 226.4 4.9 123900 10.6 110 16900 2.7 123900 5.8 470 16900
A 904_ 281.4 3.9 123900 8.5 160 16900 2.1 123900 4.6 520 16900
A 904_ 304.9 3.6 123900 7.8 280 16900 2.0 123900 4.3 650 16900
A 904_ 355.8 3.1 123900 6.7 280 16900 1.7 123900 3.7 650 16900
A 904_ 385.4 2.9 123900 6.2 390 16900 1.6 123900 3.4 760 16900
A 904_ 449.2 2.4 123900 5.3 350 16900 1.3 123900 2.9 720 16900
A 904_ 486.6 2.3 123900 4.9 450 16900 1.2 123900 2.7 790 16900
A 904_ 555.3 2.0 123900 4.3 410 16900 1.1 123900 2.3 790 16900
A 904_ 601.6 1.8 123900 4.0 510 16900 1.0 123900 2.2 790 16900
A 904_ 707.9 1.6 123900 3.4 480 16900 0.85 123900 1.8 790 16900
A 904_ 766.9 1.4 123900 3.1 580 16900 0.78 123900 1.7 790 16900
A 904_ 865.1 1.3 123900 2.8 500 16900 0.69 123900 1.5 790 16900
A 904_ 937 1.2 123900 2.6 600 16900 0.64 123900 1.4 790 16900
A 904_ 1025 1.1 123900 2.3 540 16900 0.59 123900 1.3 790 16900
A 904_ 1111 0.99 123900 2.2 630 16900 0.54 123900 1.2 790 16900
A 904_ 1222 0.90 123900 2.0 550 16900 0.49 123900 1.1 790 16900
A 904_ 1324 0.83 123900 1.8 640 16900 0.45 123900 0.99 790 16900
A 904_ 1507 0.73 123900 1.6 540 16900 0.40 123900 0.87 790 16900
A 904_ 1632 0.67 123900 1.5 650 16900 0.37 123900 0.80 790 16900
(–) Contact our Technical Service advising radial load data (rotation direction, angle, offset)

63
2.14 MOTOR AVAILABILITY
Matches of motors and gearboxes listed in tables (B12), procedure described at chapter 1.8, based on torque/hp
(B13) and (B14) here after are purely based on geomet- rating. Combinations featuring the gear ratios within
rical compatibility. When selecting a gearmotor refer to brackets are not possible.

(B12)

(IM B5)

63 71 80 90 100 112 132 160 180 200 225 250

A 10 2 i= 5.5_91.6 5.5_91.6 5.5_65.9 5.5_65.9 5.5_65.9 5.5_65.9

7.3_92.3 7.3_92.3
A 20 2 i= (10.3) (10.3)
5.4_79.9 5.4_79.9 5.4_79.9 5.4_79.9

A 20 3 i= 120.5_380.9 120.5_380.9 120.5_380.9 120.5_380.9 120.5_380.9 120.5_380.9

9.3_97.5 9.3_97.5
A 30 2 i= (10.5;13.6) (10.5;13.6)
5.4_97.5 5.4_97.5 5.4_97.5 5.4_97.5

A 30 3 i= 120.5_400.8 120.5_400.8 120.5_400.8 120.5_400.8 120.5_400.8 120.5_400.8

11.7_79.2 11.7_79.2
A 41 2 i= (13.8_17.8) (13.8_17.8)
5.2_79.2 5.2_79.2 5.2_79.2 5.2_79.2 5.2_45.1

A 41 3 i= 92.8_376.8 92.8_376.8 92.8_376.8 92.8_376.8 92.8_376.8 92.8_376.8

A 50 2 i= 20.9 20.9 7.7_20.9 7.7_20.9 7.7_20.9 7.7_20.9 7.7_20.9 7.7_20.9 7.7_20.9

A 50 3 i= 51.7_190.6 51.7_190.6 24_190.6 24_190.6 24_190.6 24_190.6 24_109.4 24_109.4 24_109.4

A 50 4 i= 211_778.2 211_778.2 211_778.2 211_778.2 211_778.2 211_778.2

A 60 2 i= 10.3_20.6 10.3_20.6 10.3_20.6 10.3_20.6 7.9_20.6 7.9_20.6 7.9_20.6

A 60 3 i= 65.0_185.8 65.0_185.8 25.7_185.8 25.7_185.8 25.7_185.8 25.7_185.8 25.7_133.3 25.7_133.3 25.7_133.3

A 60 4 i= 208.7_755.4 208.7_755.4 208.7_755.4 208.7_755.4 208.7_755.4 208.7_755.4

15.4;153.7 9.4_38.4
A 70 3 i= 66.9_153.7 66.9_153.7 66.9_153.7 66.9_153.7
(23.5_30.1)
9.4_153.7 9.4_153.7
(19.7_21.3)

A 70 4 i= 292_1715 292_1715 169.8_1715 169.8_1715 169.8_1715 169.8_1715 169.8_644.6

19.3_156.8 12.3_156.8
A 80 3 i= 82.3_156.8 82.3_156.8 82.3_156.8 82.3_156.8
(22.6_38.5) (22.6_24.5)
9.8_156.8 9.8_104 9.8_104

A 80 4 i= 354_1558 354_1558 171.3_1558 171.3_1558 171.3_1558 171.3_1558 171.3_762.1

15.6_151
A 90 3 i= 98.6_151 98.6_151 98.6_151 98.6_151 55_151
(22.3_31.5)
9.7_151 9.7_126.6 9.7_126.6 9.7_126.6

A 90 4 i= 449.2_1632 449.2_1632 166.1_1632 166.1_1632 166.1_1632 166.1_1632 166.1_937.2 166.1_937.2 166.1_937.2

64
(B13)

NEMA Motor frame

N56C N140TC N180TC N210TC N250TC N280TC N320TC

0.16…1 1.5…2 3…5 7.5…10 15…20 25…30 40…50

A 10 2 5.5_91.6 5.5_65.9 5.5_65.9

7.3_92.3
A 20 2 5.4_79.9 5.4_79.9
(10.3)

A 20 3 120.5_380.9 120.5_380.9 120.5_380.9

9.3_97.5
A 30 2 5.4_97.5 5.4_97.5
(10.5_13.6)

A 30 3 120.5_400.8 120.5_400.8 120.5_400.8

11.7_79.2
A 41 2 5.2_79.2 5.2_79.2 5.2_45.1
(13.8_17.8)

A 41 3 92.8_376.8 92.8_376.8 92.8_376.8

A 50 2 20.9 7.7_20.9 7.7_20.9 7.7_20.9 7.7_20.9 7.7_20.9

A 50 3 51.7_190.6 24.0_190.6 24.0_190.6 24.0_109.4 24.0_109.4 24.0_109.4

A 50 4 i= 211.0_778.2 211.0_778.2 211.0_778.2

A 60 2 10.3_20.6 10.3_20.6 7.9_20.6 7.9_20.6 7.9_20.6

A 60 3 65.5_185.8 25.7_185.8 25.7_185.8 25.7_133.3 25.7_133.3 25.7_133.3

A 60 4 208.7_755.4 208.7_755.4 208.7_755.4 208.7_755.4

15.4_153.7
A 70 3 66.9_153.7 66.9_153.7 9.4_153.7 9.4_153.7
(23.5_30.1)

A 70 4 292_1715 169.8_1715 169.8_1715 169.8_644.6

19.3_156.8 12.3_156.8
A 80 3 82.3_156.8 9.8_156.8 9.8_104.0
(22.6_38.5) (22.6_24.5)

A 80 4 354.0_1558 171.3_1558 171.3_1558 171.3_762.1

15.6_151.0
A 90 3 98.6_151.0 55.0_151.0 9.7_151.0 9.7_126.6
(22.3_31.5)

A 90 4 449.2_1632 166.1_1632 166.1_1632 166.1_937.2 166.1_937.2 166.1_937.2

65
(B14)

Integral gearmotors

M05 M1 M2 M3 M4 M5

A 10 2 5.5_91.6 5.5_91.6 5.5_65.9 5.5_65.9

7.3_92.3 7.3_92.3
A 20 2 5.4_79.9 5.4_79.9
(10.3) (10.3)

A 20 3 120.5_380.9 120.5_380.9 120.5_380.9 120.5_380.9

9.3_97.5
A 30 2 5.4_97.5 5.4_97.5
(10.5_13.6)

A 30 3 120.5_400.8 120.5_400.8 120.5_400.8 120.5_400.8

11.7_79.2
A 41 2 5.2_79.2 5.2_79.2 5.2_45.1
(13.8_17.8)

A 41 3 92.8_376.8 92.8_376.8 92.8_376.8 92.8_376.8

A 50 2 20.9 7.7_20.9 7.7_20.9 7.7_20.9

A 50 3 51.7_190.6 24.0_190.6 24.0_190.6 24.0_109.4

i=
A 50 4 211.0_778.2 211.0_778.2 211.0_778.2

A 60 2 10.3_20.6 10.3_20.6 7.9_20.6 7.9_20.6

A 60 3 25.7_185.8 25.7_185.8 25.7_133.3 25.7_133.3

A 60 4 208.7_755.4 208.7_755.4 208.7_755.4

15.4_153.7 15.4_153.7
A 70 3 66.9_153.7 66.9_153.7
(23.5_30.1) (23.5_30.1)

A 70 4 292.0_1715 169.8_1715 169.8_1715 169.8_644.6

19.3_156.8 19.3_156.8
A 80 3 82.3_156.8
(22.6_38.5) (22.6_38.5)

A 80 4 354.0_1558 171.3_1558 171.3_1558 171.3_762.1

A 90 3 98.6_151.0 55.0_151.0 55.0_151.0

A 90 4 449.2_1632 166.1_1632 166.1_1632 166.1_937.2

66
2.15 MASS MOMENT OF INERTIA

A 10
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 102_5.5 24 59 90 121 — — — — 43
A 102_7.2 14 50 81 112 — — — — 36
A 102_9.6 7.1 43 74 105 — — — — 31
A 102_10.6 12 48 78 109 — — — — 33
A 102_12.3 4.8 40 71 102 — — — — 26
A 102_13.9 7.1 43 74 109 — — — — 29
A 102_18.6 4.8 40 71 102 — — — — 24
A 102_23.8 2.4 38 69 100 — — — — 24
A 102_28.6 2.4 38 69 100 — — — — 21
A 102_35.1 1.7 38 69 100 — — — — 21
A 102_45.4 1.2 38 69 100 — — — — 21
A 102_51.3 0.71 36 67 97 — — — — 21
A 102_65.9 0.48 36 67 97 — — — — 21
A 102_76.4 0.48 36 67 97 — — — — 21
A 102_91.6 0.24 36 67 97 — — — — 21

67
 A 20
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 202_5.5 57 — 124 154 — — — — 102
A 202_7.2 33 50 100 131 — — — — 78
A 202_9.6 21 43 88 119 — — — — 67
A 202_10.6 29 48 95 126 — — — — 71
A 202_12.3 12 40 78 109 — — — — 57
A 202_13.9 17 43 83 114 — — — — 62
A 202_18.6 9.5 40 76 107 — — — — 57
A 202_23.8 7.1 38 74 105 — — — — 52
A 202_28.6 4.8 38 71 102 — — — — 50
A 202_35.1 4.8 38 71 102 — — — — 50
A 202_45.4 2.4 38 69 100 — — — — 48
A 202_51.3 2.4 36 69 100 — — — — 48
A 202_65.9 2.4 36 69 100 — — — — 48
A 202_76.4 0.71 36 67 97 — — — — 48
A 202_91.6 0.48 36 — — — — — — 48

A 203_120.5 0.48 36 — — — — — — 21
A 203_146.1 0.48 36 — — — — — — 21
A 203_178.3 0.24 36 — — — — — — 21
A 203_221.3 0.24 36 — — — — — — 21
A 203_260.5 0.24 36 — — — — — — 21
A 203_329.4 0.24 36 — — — — — — 21
A 203_380.9 0.24 36 — — — — — — 21

68
 A 30
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 302_5.4 107 — — 204 — — — — 164
A 302_7.0 69 — 138 166 — — — — 124
A 302_9.3 38 74 105 135 — — — — 95
A 302_10.5 55 — 121 152 — — — — 109
A 302_11.8 26 62 93 124 — — — — 81
A 302_13.6 36 — — 133 — — — — 93
A 302_18.0 21 57 88 119 — — — — 76
A 302_22.8 14 50 81 112 — — — — 71
A 302_29.3 9.5 45 76 107 — — — — 67
A 302_36.6 7.1 43 74 105 — — — — 64
A 302_43.4 4.8 40 71 102 — — — — 62
A 302_52.7 4.8 40 71 102 — — — — 59
A 302_66.0 2.4 38 69 100 — — — — 59
A 302_76.5 2.4 38 69 100 — — — — 59
A 302_97.5 2.4 38 — — — — — — 57

A 303_120.5 2.4 38 — — — — — — 21
A 303_150.7 2.4 38 — — — — — — 21
A 303_178.6 2.4 38 — — — — — — 21
A 303_216.6 2.4 38 — — — — — — 21
A 303_271.5 2.4 38 — — — — — — 21
A 303_314.6 2.4 38 — — — — — — 21
A 303_400.8 0.95 38 — — — — — — 21

69
 A 41
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 412_5.2 304 — — 401 753 — — — 553
A 412_7.1 173 — — 271 622 — — — 423
A 412_9.2 107 — — 204 556 — — — 356
A 412_10.1 140 — — 238 589 — — — 390
A 412_11.7 69 105 135 166 518 — — — 318
A 412_13.8 86 — — 183 534 — — — 335
A 412_17.8 52 — 119 150 501 — — — 271
A 412_22.7 36 71 102 133 485 — — — 254
A 412_28.3 26 62 93 124 — — — — 242
A 412_35.9 40 76 107 138 — — — — 233
A 412_45.1 36 71 102 133 — — — — 228
A 412_53.1 33 69 100 131 — — — — 226
A 412_64.2 31 67 97 128 — — — — 223
A 412_79.2 29 64 95 126 — — — — 221

A 413_92.8 26 62 93 124 — — — — 219

A 413_115.9 4.8 40 71 102 — — — — 50
A 413_146.9 2.4 38 69 100 — — — — 50
A 413_184.4 2.4 38 69 100 — — — — 50
A 413_217.4 2.4 38 69 100 — — — — 48
A 413_262.5 2.4 38 69 100 — — — — 48
A 413_324.2 2.4 38 69 100 — — — — 48
A 413_376.8 2.4 38 69 100 — — — — 48

70
 A 50
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 502_7.7 356 — — 454 808 2209 2162 — 572
A 502_9.7 242 — — 340 691 2114 2043 — 458
A 502_13.1 150 — — 245 599 2019 1948 — 363
A 502_16.6 100 — — 195 549 1948 1900 — 314
A 502_20.9 67 100 133 164 515 1924 1876 — 283

A 503_24.0 143 — 209 240 591 1995 1948 — 356

A 503_26.4 138 — 204 235 587 1995 1948 — 352
A 503_32.4 95 — 162 192 544 1948 1900 — 309
A 503_35.6 93 — 159 190 542 1948 1900 — 306
A 503_40.9 64 — 131 162 513 1924 1876 — 280
A 503_45.0 62 — 128 159 511 1924 1876 — 278
A 503_51.7 45 81 112 143 494 1900 1853 — 261
A 503_56.8 45 78 109 140 494 1900 1853 — 259
A 503_63.9 33 67 100 131 482 1900 1829 — 249
A 503_70.2 33 67 97 128 482 1900 1829 — 247
A 503_81.5 21 57 88 119 470 1876 1829 — 238
A 503_89.5 21 57 88 119 470 1876 1829 — 238
A 503_99.5 14 50 81 112 463 1876 1829 — 230
A 503_109.4 14 50 81 112 463 1876 1829 — 230
A 503_118.0 12 48 78 109 — — — — 228
A 503_129.7 12 48 78 109 — — — — 228
A 503_140.6 9.5 43 76 105 — — — — 223
A 503_154.6 9.5 43 76 105 — — — — 223
A 503_173.4 7.1 40 71 102 — — — — 221
A 503_190.6 4.8 40 71 102 — — — — 221

For the values of the moment of inertia of 4-stage gearboxes, please contact our Technical Service department.

71
 A 60
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 602_7.9 855 — — — 1283 2708 2660 — 1354
A 602_10.3 537 — 603 634 974 2399 2352 — 1045
A 602_12.7 382 — 447 477 831 2233 2185 — 879
A 602_16.7 223 — 290 321 672 2090 2019 — 713
A 602_20.6 159 — 226 257 608 2019 1971 — 658

A 603_25.7 335 — 401 430 784 2185 2138 — 831

A 603_27.9 328 — 394 425 784 2185 2138 — 831
A 603_31.7 247 — 314 344 696 2114 2043 — 736
A 603_34.3 245 — 311 342 694 2114 2043 — 736
A 603_41.7 145 — 211 242 596 1995 1948 — 644
A 603_45.2 145 — 211 240 594 1995 1948 — 641
A 603_51.3 119 — 176 207 558 1971 1924 — 608
A 603_55.6 107 — 173 204 556 1971 1924 — 606
A 603_65.0 76 — 143 173 525 1948 1876 — 575
A 603_70.4 76 — 143 173 525 1924 1876 — 575
A 603_79.7 50 — 116 147 499 1900 1853 — 549
A 603_86.4 50 — 116 147 499 1900 1853 — 549
A 603_99.5 48 — 102 133 485 1900 1853 — 534
A 603_107.8 36 — 102 133 485 1900 1853 — 532
A 603_123.0 26 — 93 124 475 1876 1829 — 525
A 603_133.3 26 — 93 124 475 1876 1829 — 523
A 603_144.0 19 — 86 119 — — — — 518
A 603_156.0 19 — 86 119 — — — — 518
A 603_171.5 14 — 81 112 — — — — 513
A 603_185.8 14 — 81 112 — — — — 513

For the values of the moment of inertia of 4-stage gearboxes, please contact our Technical Service department.

72
 A 70
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 703_9.4 — — — — — 4442 4394 — 3563
A 703_10.2 — — — — — 4347 4276 — 3468
A 703_12.1 — — — — — 3563 3515 — 2684
A 703_13.1 — — — — — 3492 3444 — 2637
A 703_15.4 1069 — — — 1520 2945 2874 — 2067
A 703_16.7 1045 — — — 1496 2898 2850 — 2019
A 703_19.7 713 — — — 1164 2589 2542 — 1710
A 703_21.3 689 — — — 1140 2565 2518 — 1686
A 703_23.5 — — — — 1354 2755 2708 — 1876
A 703_27.8 — — — — 1164 2803 2755 — 1924
A 703_30.1 — — — — 1164 2779 2732 — 1924
A 703_35.4 610 — — — 1069 2470 2423 — 1591
A 703_38.4 603 — — — 1045 2470 2399 — 1591
A 703_45.2 435 — — — 879 2304 2233 — 1401
A 703_49.0 432 — — — 879 2280 2233 — 1401
A 703_53.2 356 — — — 808 2209 2162 — 1330
A 703_57.7 356 — — — 808 2209 2162 — 1330
A 703_66.9 230 — — 316 679 2090 2043 — 1211
A 703_72.5 228 — — 314 675 2090 2043 — 1211
A 703_79.3 162 — — 252 610 2019 1971 — 1140
A 703_85.9 159 — — 249 608 2019 1971 — 1140
A 703_96.2 128 — — 223 580 1995 1948 — 1116
A 703_104.2 128 — — 223 577 1995 1924 — 1116
A 703_120.6 81 — — 178 530 1948 1876 — 1069
A 703_130.7 81 — — 176 530 1948 1876 — 1069
A 703_141.9 57 — — 154 506 1924 1853 — 1045
A 703_153.7 57 — — 154 506 1924 1853 — 1045

For the values of the moment of inertia of 4-stage gearboxes, please contact our Technical Service department.

73
 A 80
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 803_9.8 — — — — — — 7601 14513 6793
A 803_10.7 — — — — — — 7340 14276 6556
A 803_12.3 — — — — — 5677 5677 12613 4869
A 803_13.3 — — — — — 5511 5534 12447 4727
A 803_15.5 — — — — — 4442 4394 11354 3563
A 803_16.7 — — — — — 4347 4276 11259 3563
A 803_19.3 1639 — — — 2090 3492 3444 10451 2637
A 803_20.9 1568 — — — 2019 3444 3373 10380 2565
A 803_22.6 — — — — — — 4869 11781 4062
A 803_24.5 — — — — — — 4822 11734 4014
A 803_28.2 — — — — — 3919 3943 10855 3135
A 803_30.6 — — — — — 3895 3895 10831 3088
A 803_35.5 — — — — — 3325 3278 10261 2470
A 803_38.5 — — — — — 3325 3254 10238 2447
A 803_44.5 926 — — — 1378 2803 2732 9739 1924
A 803_48.2 926 — — — 1378 2779 2732 9739 2138
A 803_55.2 696 — — — 1140 2565 2494 9477 1663
A 803_59.8 689 — — — 1140 2542 2494 9477 1663
A 803_66.8 527 — — — 974 2399 2328 9287 1496
A 803_72.4 523 — — — 974 2375 2328 9287 1496
A 803_82.3 356 — 406.2 437 808 2233 2162 9121 1330
A 803_89.2 356 — 403.8 435 808 2209 2162 9169 1330
A 803_96.0 333 — 382.4 411 760 2185 2138 9074 1306
A 803_104.0 318 — 380.0 409 760 2185 2114 9074 1306
A 803_116.0 216 — 280.3 311 665 2067 2019 8979 1188
A 803_125.6 216 — 280.3 311 665 2067 2019 — 1188
A 803_144.7 128 — 194.8 238 580 1995 1948 — 1116
A 803_156.8 — — 68.9 100 454 1853 1805 — 974

For the values of the moment of inertia of 4-stage gearboxes, please contact our Technical Service department.

74
 A 90
J (·10-4) [lb·ft2]
i
Type
(ratio) NEMA Motor frame
N56C N140TC N180TC N210TC N250TC N280TC N320TC
A 903_9.7 — — — — — — 14181 21116 21330
A 903_10.5 — — — — — — 13658 20594 20808
A 903_12.6 — — — — — — 9549 16461 16698
A 903_13.7 — — — — — — 9240 16176 16390
A 903_15.6 — — — — — — 7268 14181 14418
A 903_16.9 — — — — — — 7055 13990 14204
A 903_19.4 3539 — — — — 5606 5558 12518 12589
A 903_21.0 3397 — — — — 5487 5416 12399 12447
A 903_22.3 — — — — — — 7743 14679 14893
A 903_24.1 — — — — — — 7648 14584 14798
A 903_29.1 — — — — — — 5772 12708 12922
A 903_31.5 — — — — — — 5724 12637 12874
A 903_35.8 — — — — — — 4774 11710 11924
A 903_38.8 — — — — — — 4751 11663 11876
A 903_44.6 1924 — — — — 4014 3943 10926 10974
A 903_48.3 1900 — — — — 3990 3919 10903 10950
A 903_55.0 1568 — — — 2019 3420 3373 10380 10404
A 903_59.6 1568 — — — 1995 3420 3349 10356 10380
A 903_68.8 1140 — — — 1591 2993 2945 9929 9881
A 903_74.5 1116 — — — 1568 2993 2922 9905 9881
A 903_80.4 1021 — — — 1473 2874 2827 9786 9786
A 903_87.1 1021 — — — 1473 2874 2827 9786 9786
A 903_98.6 665 — 712.6 760.1 1116 2518 2470 9430 9477
A 903_106.8 665 — 712.6 736.3 1116 2518 2470 9430 9477
A 903_116.9 546 — 596.2 627.1 974 2399 2352 9287 9359
A 903_126.7 532 — 593.8 622.3 974 2399 2328 9287 9359
A 903_139.4 356 — 408.6 451.3 784 2209 2162 — 9169
A 903_151.0 — — 71.3 102.1 456 1876 1805 — 8836

For the values of the moment of inertia of 4-stage gearboxes, please contact our Technical Service department.

75
 Shaft mount, integral motor A 10 2

2.16 DIMENSIONS
AB CB
VA C
VB VB QB

OA J P
U
D
H
G

E FA FB
AC
A UZ

UY Output Shaft B BA BB BC Mounting face

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0012
4.61 3.74 4.72 3.94 3.150 -0.0024 2.76 2.95 1.97 1.97 0.35 0.37 3.94 5.51 2.76
A 10 2 -0.030 M8x12 [mm]
117 95 120 100 80 -0.060 70 75 50 50 9 9.5 100 140 70

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0011
A 10 2 NUH 1.000 + 0.0003 1.114 0.250 2.36 0.71

Motor
Weight
AB C CB P
[lbs / kg]
3.74 16.08 18.68 4.76
A 10 2_S05 M05 31 / 14
95 408.5 474.5 121
4.25 16.28 18.76 5.43
A 10 2_S1 M1S 35 / 16
108 413.5 476.5 138
4.25 17.22 19.63 5.43
A 10 2_S1 M1L 37 / 17
108 437.5 498.5 138
4.69 18.37 21.12 6.14
A 10 2_S2 M2S 49 / 22
119 466.5 536.5 156
5.59 20.06 23.84 7.68
A 10 2_S3 M3S 66 / 30
142 509.5 605.5 195
5.59 21.32 24.90 7.68
A 10 2_S3 M3L 82 / 37
142 541.5 632.5 195

inch
Dimensions are
mm
76
A 10 2 Shaft mount - NEMA C - face adapter
VA C
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0012
4.61 3.74 4.72 3.94 3.150 -0.0024 2.76 2.95 1.97 1.97 0.35 0.37 3.94 5.51 2.76
A 10 2 -0.030 M8x12 [mm]
117 95 120 100 80 -0.060 70 75 50 50 9 9.5 100 140 70

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0011
A 10 2 NUH 1.000 + 0.0003 1.114 0.250 2.36 0.71

NEMA flange Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 18 / 8 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 20 / 9 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 29 / 13 N180TC 0.250 1.125 1.241

C
N56C N140TC N180TC
11.91 11.91 12.66
A 10 2
302.5 302.5 321.5

inch
Dimensions are
mm
77
 Solid input / hollow output shaft A 10 2

VA C
VB VB QB FV
KEY

OA U J FU

D FM DA
H TAP
G

E FA FB
AC

UZ FZ

UY Output Shaft B BA BB BC Mounting face Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0012
4.61 3.74 4.72 3.94 3.150 -0.0024 2.76 2.95 1.97 1.97 0.35 0.37 3.94 5.51 2.76
A 10 2 -0.030 M8x12 [mm]
117 95 120 100 80 -0.060 70 75 50 50 9 9.5 100 140 70

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0011
A 10 2 NUH 1.000 + 0.0003 1.114 0.250 2.36 0.71

Input shaft (Inch series)

FU FZ FV Key FM
+0
A 10 2 NHS 0.625 - 0.0004 0.710 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]

Weight
C [lbs / kg]
11.40
A 10 2 18 / 8
289.5

inch
Dimensions are
mm
78
A 10 2 Shaft mount - IEC B5 motor adapter
6.063
154
VA C (P63)
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0012
4.61 3.74 4.72 3.94 3.150 -0.0024 2.76 2.95 1.97 1.97 0.35 0.37 3.94 5.51 2.76
A 10 2 -0.030 M8x12 [mm]
117 95 120 100 80 -0.060 70 75 50 50 9 9.5 100 140 70

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0011
A 10 2 NUH 1.000 + 0.0003 1.114 0.250 2.36 0.71

IEC flange (mm) Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
P63 140 115 95 M8x19 4 18 / 8 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 18 / 8 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 20 / 9
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 29 / 13 P100, P112 8 28 31.3

C
P63 P80 P100
P71 P90 P112
11.12 11.89 12.28
A 10 2
282.5 302 312

inch
Dimensions are
mm
79
 Shaft mount, integral motor A 20 2 A 20 3
AB CB
VA C
VB VB QB

OA J P
U
D
H
G

E FA FB
AC
A UZ

UY Output Shaft B BA BB BC Mounting face

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0014
5.35 4.33 5.51 4.53 3.740 -0.0028 3.15 3.54 2.36 2.36 0.35 0.37 4.72 6.30 3.15
A 20 2, A 20 3 -0.036 M8x15 [mm]
136 110 140 115 95 -0.071 80 90 60 60 9 9.5 120 160 80

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 20 2, A 20 3 NUH 1.250 + 0.0004 1.367 0.250 2.76 0.87

Motor
Weight
AB C CB P
[lbs / kg]
3.74 17.01 19.61 4.76
A 20 2_S05 M05 40 / 18
95 432 498 121
4.25 17.20 19.69 5.43
A 20 2_S1 M1S 42 / 19
108 437 500 138
4.25 18.15 20.55 5.43
A 20 2_S1 M1L 46 / 21
108 461 522 138
4.69 19.29 22.05 6.14
A 20 2_S2 M2S 57 / 26
119 490 560 156
5.59 20.98 24.76 7.68
A 20 2_S3 M3S 75 / 34
142 533 629 195
5.59 22.24 25.83 7.68
A 20 2_S3 M3L 90 / 41
142 565 656 195
3.74 18.01 21.79 4.76
A 20 3_S05 M05 40 / 18
95 457.5 553.5 121
4.25 18.21 21.87 5.43
A 20 3_S1 M1S 44 / 20
108 462.5 555.5 138
4.25 19.15 22.74 5.43
A 20 3_S1 M1L 46 / 21
108 486.5 577.5 138
4.69 21.48 24.23 6.14
A 20 3_S2 M2S 57 / 26
119 545.5 615.5 156
5.59 23.17 26.95 7.68
A 20 3_S1 M3S 75 / 34
142 588.5 684.5 195
5.59 24.43 28.01 7.68
A 20 3_S1 M3L 90 / 41 inch
142 620.5 711.5 195 Dimensions are
mm
80
A 20 2 A 20 3 Shaft mount - NEMA C - face adapter
VA C
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0014
5.35 4.33 5.51 4.53 3.740 -0.0028 3.15 3.54 2.36 2.36 0.35 0.37 4.72 6.30 3.15
A 20 2, A 20 3 -0.036 M8x15 [mm]
136 110 140 115 95 -0.071 80 90 60 60 9 9.5 120 160 80

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 20 2, A 20 3 NUH 1.250 + 0.0004 1.367 0.250 2.76 0.87

NEMA flange Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 26 / 12 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 29 / 13 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 37 / 17 N180TC 0.250 1.125 1.241

C
N56C N140TC N180TC
12.83 12.83 13.58
A 20 2
326 326 345
15.00 15.00 15.77
A 20 3
381 381 400.5

inch
Dimensions are
mm
81
 Solid input / hollow output shaft A 20 2 A 20 3
VA C
VB VB QB FV
KEY

OA U J FU

D FM DA
H TAP
G

E FA FB
AC

UZ FZ

UY Output Shaft B BA BB BC Mounting face Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0014
5.35 4.33 5.51 4.53 3.740 -0.0028 3.15 3.54 2.36 2.36 0.35 0.37 4.72 6.30 3.15
A 20 2, A 20 3 -0.036 M8x15 [mm]
136 110 140 115 95 -0.071 80 90 60 60 9 9.5 120 160 80

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 20 2, A 20 3 NUH 1.250 + 0.0004 1.367 0.250 2.76 0.87

Input shaft (Inch series)

FU FZ FV Key FM
+0
A 20 2 NHS 0.750 -0.0005 0.830 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]
+0
A 20 3 NHS 0.625 -0.0004 0.710 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]

Weight
C [lbs / kg]
14.02
A 20 2 27 / 12
356
14.51
A 20 3 27 / 12
368.5

inch
Dimensions are
mm
82
A 20 2 A 20 3 Shaft mount - IEC B5 motor adapter
6.063
154
VA C (P63)
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0014
5.35 4.33 5.51 4.53 3.740 -0.0028 3.15 3.54 2.36 2.36 0.35 0.37 4.72 6.30 3.15
A 20 2, A 20 3 -0.036 M8x15 [mm]
136 110 140 115 95 -0.071 80 90 60 60 9 9.5 120 160 80

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 20 2, A 20 3 NUH 1.250 + 0.0004 1.367 0.250 2.76 0.87

IEC flange (mm) Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
P63 140 115 95 M8x19 4 29 / 13 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 29 / 13 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 31 / 14
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 40 / 18 P100, P112 8 28 31.3

C
P63 P80 P100
P71 P90 P112
12.05 12.81 13.21
A 20 2
306 325.5 335.5
14.23 15.00 15.39
A 20 3
361.5 381 391

inch
Dimensions are
mm

83
 Shaft mount, integral motor A 30 2 A 30 3
AB CB
VA C
VB VB QB

OA J P
U
D
H
G

E FA FB FC
AC
A UZ

UY Output Shaft B BA BB BC Mounting face

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0014
6.14 5.12 5.51 4.53 3.740 -0.0028 3.54 3.74 2.48 2.48 0.87 0.43 0.47 4.96 7.09 3.54
A 30 2, A 30 3 -0.036 M8x15 [mm]
156 130 140 115 95 -0.071 90 95 63 63 22 11 12 126 180 90

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 30 2, A 30 3 NUH 1.375 + 0.0004 1.518 0.312 3.15 0.98

Motor
Weight
AB C CB P
[lbs / kg]
4.25 18.27 20.75 5.43
A 30 2_S1 M1S 51 / 23
108 464 527 138
4.25 19.21 21.61 5.43
A 30 2_S1 M1L 53 / 24
108 488 549 138
4.69 20.35 23.11 6.14
A 30 2_S2 M2S 64 / 29
119 517 587 156
5.59 22.05 25.83 7.68
A 30 2_S3 M3S 84 / 38
142 560 656 195
5.59 23.31 26.89 7.68
A 30 2_S3 M3L 99 / 45
142 592 683 195
3.74 20.33 22.93 4.76
A 30 3_S05 M05 49 / 22
95 516.5 582.5 121
4.25 20.53 23.01 5.43
A 30 3_S1 M1S 53 / 24
108 521.5 584.5 138
4.25 21.48 23.88 5.43
A 30 3_S1 M1L 57 / 26
108 545.5 606.5 138
4.69 22.62 25.37 6.14
A 30 3_S2 M2S 64 / 29
119 574.5 644.5 156
5.59 24.31 28.09 7.68
A 30 3_S3 M3S 84 / 38
142 617.5 713.5 195
5.59 25.57 29.15 7.68 inch
A 30 3_S3 M3L 99 / 45 Dimensions are
142 649.5 740.5 195 mm
84
A 30 2 A 30 3 Shaft mount - NEMA C - face adapter
VA C
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB FC NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB
Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0014
6.14 5.12 5.51 4.53 3.740 -0.0028 3.54 3.74 2.48 2.48 0.87 0.43 0.47 4.96 7.09 3.54
A 30 2, A 30 3 -0.036 M8x15 [mm]
156 130 140 115 95 -0.071 90 95 63 63 22 11 12 126 180 90

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 30 2, A 30 3 NUH 1.375 + 0.0004 1.518 0.312 3.15 0.98

NEMA flange Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 35 / 16 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 37 / 17 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 44 / 20 N180TC 0.250 1.125 1.241

C
N56C N140TC N180TC
13.90 13.90 14.65
A 30 2
353 353 372
16.16 16.16 16.91
A 30 3
410.5 410.5 429.5

inch
Dimensions are
mm
85
 Solid input / hollow output shaft A 30 2 A 30 3
VA C
VB VB QB FV
KEY

OA U J FU

D FM DA
H TAP
G

E FA FB FC
AC

UZ FZ

UY Output Shaft B BA BB BC Mounting face Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0014
6.14 5.12 5.51 4.53 3.740 -0.0028 3.54 3.74 2.48 2.48 0.87 0.43 0.47 4.96 7.09 3.54
A 30 2, A 30 3 -0.036 M8x15 [mm]
156 130 140 115 95 -0.071 90 95 63 63 22 11 12 126 180 90

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 30 2, A 30 3 NUH 1.375 + 0.0004 1.518 0.312 3.15 0.98

Input shaft (Inch series)

FU FZ FV Key FM
+0
A 30 2 NHS 0.750 -0.0005 0.830 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]
+0
A 30 3 NHS 0.625 -0.0004 0.710 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]

Weight
C [lbs / kg]
15.08
A 30 2 38 / 17
383
15.65
A 30 3 38 / 17
397.5

inch
Dimensions are
mm
86
A 30 2 A 30 3 Shaft mount - IEC B5 motor adapter
6.063
154
C (P63)
VA
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB FC NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0014
6.14 5.12 5.51 4.53 3.740 -0.0028 3.54 3.74 2.48 2.48 0.87 0.43 0.47 4.96 7.09 3.54
A 30 2, A 30 3 -0.036 M8x15 [mm]
156 130 140 115 95 -0.071 90 95 63 63 22 11 12 126 180 90

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 30 2, A 30 3 NUH 1.375 + 0.0004 1.518 0.312 3.15 0.98

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 38 / 17 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 38 / 17 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 40 / 18
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4 49 / 22 P100, P112 8 28 31.3

C
P63 P80 P100
P71 P90 P112
13.11 13.88 14.27
A 30 2
333 352.5 362.5
15.37 16.14 16.54
A 30 3
390.5 410 420

inch
Dimensions are
mm
87
 Shaft mount, integral motor A 41 2 A 41 3
AB CB
VA C
VB VB QB

OA J P
U
D
H
G

E FA FB FC
AC
A UZ

UY Output Shaft B BA BB BC Mounting face

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0017
7.17 6.10 7.87 6.50 5.118 -0.0033 4.41 4.72 3.15 3.15 0.79 0.51 0.55 6.30 8.82 4.41
A 41 2, A 41 3 -0.043 M12x19 [mm]
182 155 200 165 130 -0.083 112 120 80 80 20 13 14 160 224 112

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 41 2, A 41 3 NUH 1.625 + 0.0004 1.796 0.375 3.66 1.18

Motor
Weight
AB C CB P
[lbs / kg]
4.25 19.92 22.40 5.43
A 41 2_S1 M1S 95 / 43
108 506 569 138
4.25 20.87 23.27 5.43
A 41 2_S1 M1L 97 / 44
108 530 591 138
4.69 22.01 24.76 6.14
A 41 2_S2 M2S 108 / 49
119 559 629 156
5.59 23.70 27.48 7.68
A 41 2_S3 M3S 128 / 58
142 602 698 195
5.59 24.96 28.54 7.68
A 41 2_S3 M3L 143 / 65
142 634 725 195
7.60 29.21 33.50 10.16
A 41 2_S4 M4S 201 / 91
193 742 851 258
7.60 29.21 33.50 10.16
A 41 2_S4 M4L 243 / 110
193 742 851 258
3.74 22.15 24.74 4.76
A 41 3_S05 M05 101 / 46
95 562.5 628.5 121
4.25 22.34 24.82 5.43
A 41 3_S1 M1S 106 / 48
108 567.5 630.5 138
4.25 23.29 25.69 5.43
A 41 3_S1 M1L 108 / 49
108 591.5 652.5 138
4.69 24.43 27.19 6.14
A 41 3_S2 M2S 128 / 58
119 620.5 690.5 156
5.59 26.12 29.90 7.68
A 41 3_S3 M3S 137 / 62
142 663.5 759.5 195
5.59 27.38 30.96 7.68 inch
A 41 3_S3 M3L 150 / 68 Dimensions are
142 695.5 786.5 195 mm
88
A 41 2 A 41 3 Shaft mount - NEMA C - face adapter
VA C
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB FC NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0017
7.17 6.10 7.87 6.50 5.118 -0.0033 4.41 4.72 3.15 3.15 0.79 0.51 0.55 6.30 8.82 4.41
A 41 2, A 41 3 -0.043 M12x19 [mm]
182 155 200 165 130 -0.083 112 120 80 80 20 13 14 160 224 112

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 41 2, A 41 3 NUH 1.625 + 0.0004 1.796 0.375 3.66 1.18

NEMA flange Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 84 / 38 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 86 / 39 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 95 / 43 N180TC 0.250 1.125 1.241
N210TC 8.996 7.250 8.500 0.551 0.216 101 / 46 N210TC 0.312 1.375 1.518

C
N56C N140TC N180TC N210TC
15.55 15.55 16.30 17.54
A 41 2
395 395 414 445.5
17.97 17.97 18.72
A 41 3 —
456.5 456.5 475.5

inch
Dimensions are
mm
89
 Solid input / hollow output shaft A 41 2 A 41 3
VA C
VB VB QB FV
KEY

OA U J FU

D FM DA
H TAP
G

E FA FB FC
AC

UZ FZ

UY Output Shaft B BA BB BC Mounting face Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0017
7.17 6.10 7.87 6.50 5.118 -0.0033 4.41 4.72 3.15 3.15 0.79 0.51 0.55 6.30 8.82 4.41
A 41 2, A 41 3 -0.043 M12x19 [mm]
182 155 200 165 130 -0.083 112 120 80 80 20 13 14 160 224 112

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 41 2, A 41 3 NUH 1.625 + 0.0004 1.796 0.375 3.66 1.18

Input shaft (Inch series)

FU FZ FV Key FM
+0
A 41 2 NHS 1.000 -0.0005 1.110 1.970 1/4 x 1/4 x 1 3/4 M8x19 [mm]
+0
A 41 3 NHS 0.750 -0.0004 0.830 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]

Weight
C [lbs / kg]
18.27
A 41 2 91 / 41
464
19.15
A 41 3 88 / 40
486.5

inch
Dimensions are
mm
90
A 41 2 A 41 3 Shaft mount - IEC B5 motor adapter
6.063
154
C (P63)
VA
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB FC NB
AC NA
A
UZ MA

UY Output Shaft B BA BB BC Mounting face MC Input Shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB FC G H J OA QB
-0.0017
7.17 6.10 7.87 6.50 5.118 -0.0033 4.41 4.72 3.15 3.15 0.79 0.51 0.55 6.30 8.82 4.41
A 41 2, A 41 3 -0.043 M12x19 [mm]
182 155 200 165 130 -0.083 112 120 80 80 20 13 14 160 224 112

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0013
A 41 2, A 41 3 NUH 1.625 + 0.0004 1.796 0.375 3.66 1.18

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 86 / 39 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 86 / 39 P71 5 14 16.3
P80, P90 200 165 130 M10x12 4 88 / 44 P80 6 19 21.8
P100, P112 250 215 180 M12x16 4.5 97 / 44 P90 8 24 27.3
P132 300 265 230 14 5 101 / 46 P100, P112 8 28 31.3

C
P63 P80 P100
P71 P90 P112 P132

14.76 15.53 15.93 17.36

A 41 2
375 394.5 404.5 441
17.19 17.95 18.35
A 41 3 —
436.5 456 466

inch
Dimensions are
mm

91
 Shaft mount, integral motor A 50 2 A 50 3 A 50 4
AB CB
VA C
VB VB QB

OA P
U J

D
H
G

E FA FB
AC UZ
A

0'
22°3
UY Output Shaft B BA BB Mounting face

0'
BC

22°3
Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
8.62 7.28 9.84 8.46 7.087 -0.0033 5.51 5.91 4.04 4.04 0.55 0.63 8.07 11.02 5.51
A 50 2, A 50 3, A 50 4 -0.043 M12x19 [mm]
219 185 250 215 180 -0.083 140 150 103 103 14 16 205 280 140

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 50 2, A 50 3, A 50 4 NUH 2.000 + 0.0004 2.223 0.500 4.50 1.58

Motor
Weight
AB C CB P
[lbs / kg]
A 50 2_S1 M1S 4.25 23.05 25.53 5.43
148 / 67
A 50 3_S1 M1S 108 585.5 648.5 138
A 50 2_S1 M1L 4.25 24.00 26.40 5.43
152 / 69
A 50 3_S1 M1L 108 609.5 670.5 138
A 50 2_S2 M2S 4.69 25.14 27.89 6.14
172 / 78
A 50 3_S2 M2S 119 638.5 708.5 156
A 50 2_S3 M3S 5.59 26.83 30.61 7.68
179 / 81
A 50 3_S3 M3S 142 681.5 777.5 195
A 50 2_S3 M3L 5.59 28.09 31.67 7.68
194 / 88
A 50 3_S3 M3L 142 713.5 804.5 195
A 50 2_S4 M4S 7.60 32.34 36.63 10.16
251 / 114
A 50 3_S4 M4S 193 821.5 930.5 258
A 50 2_S4 M4L 7.60 32.34 36.63 10.16
293 / 133
A 50 3_S4 M4L 193 821.5 930.5 258
A 50 2_S4 M4LC 7.60 33.72 37.62 10.16
311 / 141
A 50 3_S4 M4LC 193 856.5 955.5 258
4.25 25.87 28.35 5.43
A 50 4_S1 M1S 150 / 68
108 657 720 138
4.25 26.81 29.21 5.43
A 50 4_S1 M1L 154 / 70
108 681 742 138
4.69 27.95 30.71 6.14
A 50 4_S2 M2S 165 / 75
119 710 780 156
5.59 29.65 33.43 7.68
A 50 4_S3 M3S 168 / 76
142 753 849 195
5.59 30.91 34.49 7.68 inch
A 50 4_S3 M3L 172 / 78 Dimensions are
142 785 876 195 mm
92
A 50 2 A 50 3 A 50 4 Shaft mount - NEMA C - face adapter
VA C
NC
VB VB QB X N
DIA

OA J
U
D
H
G

E FA FB NB
AC NA
A
UZ MA

0'
22°3
UY Output Shaft B BA BB Mounting face MC Input Shaft

0'
BC

22°3
MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
8.62 7.28 9.84 8.46 7.087 -0.0033 5.51 5.91 4.04 4.04 0.55 0.63 8.07 11.02 5.51
A 50 2, A 50 3, A 50 4 -0.043 M12x19 [mm]
219 185 250 215 180 -0.083 140 150 102.5 103 14 16 205 280 140

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 50 2, A 50 3, A 50 4 NUH 2.000 + 0.0004 2.223 0.500 4.50 1.58

NEMA flange Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 137 / 62 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 139 / 63 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 148 / 67 N180TC 0.250 1.125 1.241
N210TC 8.996 7.250 8.500 0.551 0.216 150 / 68 N210TC 0.312 1.375 1.518
N250TC 13.780 7.250 8.500 0.551 0.216 159 / 72 N250TC 0.375 1.625 1.796
N280TC 13.780 9.000 10.500 0.551 0.216 159 / 72 N280TC 0.500 1.875 2.102

C
N56C N140TC N180TC N210TC N250TC N280TC
18.68 18.68 19.43 20.67 23.46 23.66
A 50 2, A 50 3
474.5 474.5 493.5 525 596 601
21.50 21.50 22.24
A 50 4 — — —
546 546 565

inch
Dimensions are
mm
93
 Solid input / hollow output shaft A 50 2 A 50 3 A 50 4
VA C

VB VB QB FV
KEY

OA U J FU

D DA
FM
H TAP
G
E FA FB
AC
A

UZ FZ

'
0' 22°30
UY Output Shaft B BA BB Mounting face Input Shaft
BC

Outline dimensions 22°3

A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
8.62 7.28 9.84 8.46 7.087 -0.0033 5.51 5.91 4.04 4.04 0.55 0.63 8.07 11.02 5.51
A 50 2, A 50 3, A 50 4 -0.043 M12x19 [mm]
219 185 250 215 180 -0.083 140 150 103 103 14 16 205 280 140

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 50 2, A 50 3, A 50 4 NUH 2.000 + 0.0004 2.223 0.500 4.50 1.58

Input shaft (Inch series)

FU FZ FV Key FM
+0
A 50 2, A 50 3 NHS 1.000 -0.0005 1.110 1.970 1/4 x 1/4 x 1 3/4 M8x19 [mm]
+0
A 50 4 NHS 0.750 -0.0005 0.830 1.570 3/16 x 3/16 x 1 3/8 M6x16 [mm]

Weight
C [lbs / kg]
21.40
A 50 2, A 50 3 168 / 76
543.5
22.68
A 50 4 170 / 77
576

inch
Dimensions are
mm
94
A 50 2 A 50 3 A 50 4 Shaft mount - IEC B5 motor adapter
6.063
154
VA C (P63)
NC
VB VB QB X N
DIA

OA J
U
D
H
G

E FA FB NB
AC NA
A
UZ MA

0'
22°3
UY Output Shaft B BA BB Mounting face MC Input Shaft

0'
BC

22°3
MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
8.62 7.28 9.84 8.46 7.087 -0.0033 5.51 5.91 4.04 4.04 0.55 0.63 8.07 11.02 5.51
A 50 2, A 50 3, A 50 4 -0.043 M12x19 [mm]
219 185 250 215 180 -0.083 140 150 102.5 103 14 16 205 280 140

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 50 2, A 50 3, A 50 4 NUH 2.000 + 0.0004 2.223 0.500 4.50 1.58

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 137 / 62 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 137 / 62 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 139 / 63
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 148 / 67 P100, P112 8 28 31.3
P132 300 265 230 14 5 150 / 68 P132 10 38 41.3
P160 12 42 45.3
P160, P180 350 300 250 18 6 159 / 72
P180 14 48 51.8

C
P63 P80 P100 P160
P132
P71 P90 P112 P180
17.89 18.66 19.06 20.49 22.48
A 50 2, A 50 3
454.5 474 484 520.5 571
20.71 21.48 21.87
A 50 4 — —
526 545.5 555.5

inch
Dimensions are
mm
95
 Shaft mount, integral motor A 60 2 A 60 3 A 60 4
AB CB

VA C

VB VB QB

P
OA U J

D
H
G

E FA FB
AC
22°30' 22°30'
A UZ

UY Output Shaft B BA BB Mounting face

BC

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
9.41 9.25 9.84 8.46 7.087 -0.0033 6.50 7.68 4.82 4.82 0.63 0.73 9.65 12.99 6.50
A 60 2, A 60 3, A 60 4 -0.043 M12x19 [mm]
239 235 250 215 180 -0.083 165 195 123 123 16 18.5 245 330 165

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 60 2, A 60 3, A 60 4 NUH 2.625 + 0.0004 2.905 0.625 4.92 1.97

Motor
Weight
AB C CB P
[lbs / kg]
A 60 2_S2 M2S 4.69 27.58 30.33 6.14
218 / 99
A 60 3_S2 M2S 119 700.5 770.5 156
A 60 2_S3 M3S 5.59 29.27 33.05 7.68
220 / 100
A 60 3_S3 M3S 142 743.5 839.5 195
A 60 2_S3 M3L 5.59 30.53 34.11 7.68
236 / 107
A 60 3_S3 M3L 142 775.5 866.5 195
A 60 2_S4 M4S 7.60 33.29 37.58 10.16
293 / 133
A 60 3_S4 M4S 193 845.5 954.5 258
A 60 2_S4 M4L 7.60 36.12 40.02 10.16
335 / 152
A 60 3_S4 M4L 193 917.5 1016.5 258
A 60 2_S4 M4LC 7.60 36.12 40.02 10.16
353 / 160
A 60 3_S4 M4LC 193 917.5 1016.5 258
A 60 2_S5 M5S 9.65 38.19 43.70 12.20
423 / 192
A 60 3_S5 M5S 245 970 1110 310
A 60 2_S5 M5L 9.65 39.92 45.43 12.20
459 / 208
A 60 3_S5 M5L 245 1014 1154 310
4.25 28.27 30.75 5.43
A 60 4_S1 M1S 207 / 94
108 718 781 138
4.25 29.21 31.61 5.43
A 60 4_S1 M1L 209 / 95
108 742 803 138
4.69 30.35 33.11 6.14
A 60 4_S2 M2S 220 / 100
119 771 841 156
5.59 32.05 35.83 7.68
A 60 4_S3 M3S 240 / 109
142 814 910 195
5.59 33.31 36.89 7.68 inch
A 60 4_S3 M3L 256 / 116 Dimensions are
142 846 937 195 mm
96
A 60 2 A 60 3 A 60 4 Shaft mount - NEMA C - face adapter
VA C
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB NB
AC NA

A 0' 22°30
22°3 '
UZ MA

UY Output Shaft B BA BB Mounting face MC Input Shaft

BC

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
9.41 9.25 9.84 8.46 7.087 -0.0033 6.50 7.68 4.82 4.82 0.63 0.73 9.65 12.99 6.50
A 60 2, A 60 3, A 60 4 -0.043 M12x19 [mm]
239 235 250 215 180 -0.083 165 195 122.5 123 16 18.5 245 330 165

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 60 2, A 60 3, A 60 4 NUH 2.625 + 0.0004 2.905 0.625 4.92 1.97

NEMA flange Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 194 / 88 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 198 / 90 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 207 / 94 N180TC 0.250 1.125 1.241
N210TC 8.996 7.250 8.500 0.551 0.216 201 / 91 N210TC 0.312 1.375 1.518
N250TC 13.780 7.250 8.500 0.551 0.216 212 / 96 N250TC 0.375 1.625 1.796
N280TC 13.780 9.000 10.500 0.551 0.216 212 / 96 N280TC 0.500 1.875 2.102

C
N56C N140TC N180TC N210TC N250TC N280TC
21.12 21.12 24.87 23.11 25.91 26.10
A 60 2, A 60 3
536.5 536.5 555.5 587 658 663
23.90 23.90 24.65 25.89
A 60 4 — —
607 607 626 657.5

inch
Dimensions are
mm
97
 Solid input / hollow output shaft A 60 2 A 60 3 A 60 4

VA C
VB VB QB FV
KEY

OA U J FU

D DA
FM
H TAP
G
E FA FB
AC
A
22°30' 22°30'
UZ FZ

UY Output Shaft B BA BB Mounting face Input Shaft

BC

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
9.41 9.25 9.84 8.46 7.087 -0.0033 6.50 7.68 4.82 4.82 0.63 0.73 9.65 12.99 6.50
A 60 2, A 60 3, A 60 4 -0.043 M12x19 [mm]
239 235 250 215 180 -0.083 165 195 123 123 16 18.5 245 330 165

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 60 2, A 60 3, A 60 4 NUH 2.625 + 0.0004 2.905 0.625 4.92 1.97

Input shaft (Inch series)

FU FZ FV Key FM
+0
A 60 2, A 60 3 NHS 1.125 -0.0005 1.230 2.360 1/4 x 1/4 x 2 5/32 M10x22 [mm]
+0
A 60 4 NHS 1.000 -0.0005 1.110 1.970 1/4 x 1/4 x 1 3/4 M8x19 [mm]

Weight
C [lbs / kg]
24.92
A 60 2, A 60 3 292 / 119
633
26.61
A 60 4 231 / 105
676

inch
Dimensions are
mm
98
A 60 2 A 60 3 A 60 4 Shaft mount - IEC B5 motor adapter
6.063
154
VA C
(P63)
NC
VB VB QB X N
DIA

OA U J

D
H
G

E FA FB NB
AC NA

A 0' 22°30
22°3 '
UZ MA

UY Output Shaft B BA BB Mounting face MC Input Shaft

BC

MB
Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0017
9.41 9.25 9.84 8.46 7.087 -0.0033 6.50 7.68 4.82 4.82 0.63 0.73 9.65 12.99 6.50
A 60 2, A 60 3, A 60 4 -0.043 M12x19 [mm]
239 235 250 215 180 -0.083 165 195 122.5 123 16 18.5 245 330 165

Output shaft (Inch series)

U UY UZ VA VB
+ 0.0016
A 60 2, A 60 3, A 60 4 NUH 2.625 + 0.0004 2.905 0.625 4.92 1.97

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 194 / 88 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 194 / 88 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 198 / 90
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 207 / 94 P100, P112 8 28 31.3
P132 300 265 230 14 5 201 / 91 P132 10 38 41.3
P160 12 42 45.3
P160, P180 350 300 250 18 6 212 / 96
P180 14 48 51.8

C
P63 P80 P100 P160
P132
P71 P90 P112 P180
21.10 21.50 22.89 24.92
A 60 2, A 60 3 —
536 546 581.5 633
23.11 23.88 24.27
A 60 4 — —
587 606.5 616.5

inch
Dimensions are
mm

99
 Shaft mount, integral motor A 70 3 A 70 4
CB
C
AB B
VA BA

VB VB BB

OA U P
J
BC

D
H
G

E FA FB
AC UZ QB

UY Output Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
11.22 11.02 10.63 9.25 8.071 -0.0038 9.02 9.06 4.33 7.24 0.71 0.87 11.57 15.12 6.10
A 70 3, A 70 4 -0.050 M14x22 [mm]
285 280 270 235 205 -0.096 229 230 110 184 18 22 294 384 155

Output shaft
U UY UZ VA VB
+ 0.0016
2.756 + 0.00039 2.949 0.787 6.02 2.36
A 70 3, A 70 4 UH + 0.04
70 + 0.01 74.9 20 153 60

Motor
Weight
AB C CB P
[lbs / kg]
4.69 27.11 29.86 6.14
A 70 3_S2 M2S 343 / 156
119 688.5 758.5 156
5.59 28.80 32.58 7.68
A 70 3_S3 M3S 362 / 164
142 731.5 827.5 195
5.59 30.06 33.64 7.68
A 70 3_S3 M3L 377 / 171
142 763.5 854.5 195
7.60 34.35 38.64 10.16
A 70 3_S4 M4S 434 / 197
193 872.5 981.5 258
7.60 34.35 38.64 10.16
A 70 3_S4 M4L 476 / 216
193 872.5 981.5 258
7.60 35.73 39.63 10.16
A 70 3_S4 M4LC 494 / 224
193 907.5 1006.5 258
9.65 37.72 43.23 12.20
A 70 3_S5 M5S 565 / 256
245 958 1098 310
9.65 39.45 44.96 12.20
A 70 3_S5 M5L 600 / 272
245 1002 1142 310
4.25 27.03 29.51 5.43
A 70 4_S1 M1S 339 / 154
108 686.5 749.5 138
4.25 27.97 30.37 5.43
A 70 4_S1 M1L 342 / 155
108 710.5 771.5 138
4.69 29.11 31.87 6.14
A 70 4_S2 M2S 352 / 160
119 739.5 809.5 156
5.59 30.81 34.59 7.68
A 70 4_S3 M3S 371 / 168
142 782.5 878.5 195
5.59 32.07 35.65 7.68
A 70 4_S3 M3L 387 / 175
142 814.5 905.5 195
7.60 36.32 40.61 10.16
A 70 4_S4 M4L 444 / 201
193 922.5 1031.5 258
7.60 36.32 40.61 10.16 inch
A 70 4_S4 M4S 486 / 220 Dimensions are
193 922.5 1031.5 258 mm
100
A 70 3 A 70 4 Shaft mount - NEMA C - face adapter
C

VA BA
NC
VB VB BB X N
DIA

OA U
J
BC

D
H
G

E FA FB NB

AC QB NA
A UZ MA

UY Output shaft MC Input shaft

MB
Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
11.22 11.02 10.63 9.25 8.071 -0.0038 9.02 9.06 4.33 7.24 0.71 0.87 11.57 15.12 6.10
A 70 3, A 70 4 -0.050 M14x22 [mm]
285 280 270 235 205 -0.096 229 230 110 184 18 22 294 384 155

Output shaft
U UY UZ VA VB
+ 0.0016
2.756 + 0.00039 2.949 0.787 6.02 2.36
A 70 3, A 70 4 UH + 0.04
70 + 0.01 74.9 20 153 60

NEMA flange Hollow input shaft

Weight MA MB MC
N NA NB NC X
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 322 / 146 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 324 / 147 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 326 / 148 N180TC 0.250 1.125 1.241
N210TC 8.996 7.250 8.500 0.551 0.216 346 / 157 N210TC 0.312 1.375 1.518
N250TC 13.780 7.250 8.500 0.551 0.216 373 / 169 N250TC 0.375 1.625 1.796
N280TC 13.780 9.000 10.500 0.551 0.216 373 / 169 N280TC 0.500 1.875 2.102

C
N56C N140TC N180TC N210TC N250TC N280TC
20.65 21.40 22.64 25.63 25.83
A 70 3 —
524.5 543.5 575 651 656
22.66 22.66 23.41 24.65
A 70 4 — —
575.5 575.5 594.5 626

inch
Dimensions are
mm
101
 Solid input / hollow output shaft A 70 3 A 70 4
C

VA B

VB VB BA

E BB

BC FV
KEY

FM
TAP

FU
OA U J

D DA
H
G

AC QB
A FA FB

UZ

UY Output Shaft FZ Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
11.22 11.02 10.63 9.25 8.071 -0.0038 9.02 9.06 4.33 7.24 0.71 0.87 11.57 15.12 6.10
A 70 3, A 70 4 -0.050 M14x22 [mm]
285 280 270 235 205 -0.096 229 230 110 184 18 22 294 384 155

Output shaft
U UY UZ VA VB
+ 0.0016
2.756 + 0.00039 2.949 0.787 6.02 2.36
A 70 3, A 70 4 UH + 0.04
70 + 0.01 74.9 20 153 60

Input shaft
FU FZ FV Key FM
+0
1.654 - 0.0006 1.772 4.331
A 70 3 HS +0 12 x 8 x 90 M12x28 [mm]
42 - 0.016 45 110
+0
A 70 4 NHS 1.000 - 0.0005 1.110 1.970 3/4 x 3/4 x 1 3/4 M8x19 [mm]

Weight
C [lbs / kg]
27.89
A 70 3 364 / 165
708.5
25.37
A 70 4 328 / 149
644.5

inch
Dimensions are
mm
102
A 70 3 A 70 4 Shaft mount - IEC B5 motor adapter
C

B
6.063
VA 154
BA
(P63)
NC
VB VB BB X N
DIA

OA U
J
BC

D
H
G

E FA FB NB

AC QB NA
A UZ MA

UY Output shaft MC Input shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
11.22 11.02 10.63 9.25 8.071 -0.0038 9.02 9.06 4.33 7.24 0.71 0.87 11.57 15.12 6.10
A 70 3, A 70 4 -0.050 M14x22 [mm]
285 280 270 235 205 -0.096 229 230 110 184 18 22 294 384 155

Output shaft
U UY UZ VA VB
+ 0.0016
2.756 + 0.00039 2.949 0.787 6.02 2.36
A 70 3, A 70 4 UH + 0.04
70 + 0.01 74.9 20 153 60

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 322 / 146 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 322 / 146 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 324 / 147
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 326 / 148 P100, P112 8 28 31.3
P132 300 265 230 14 5 346 / 157 P132 10 38 41.3
P160 12 42 45.3
P160, P180 350 300 250 18 6 373 / 169
P180 14 48 51.8
P200 400 350 300 M16x25 7 395 / 179 P200 16 55 59.3

C
P63 P80 P100 P160
P132 P200
P71 P90 P112 P180
20.63 21.02 22.46 24.65 25.63
A 70 3 —
524 534 570.5 626 651
21.87 22.64 23.03 24.35
A 70 4 — —
555.5 575 585 618.5

inch
Dimensions are
mm
103
 Shaft mount, integral motor A 80 3 A 80 4
CB
C
AB B
VA BA

VB VB BB

OA U P
J
BC

D
H
G

E FA FB
AC UZ QB

UY Output Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
13.39 12.99 11.81 10.43 9.055 -0.0038 10.71 10.83 4.80 8.23 0.91 1.02 13.03 17.99 7.28
A 80 3, A 80 4 -0.050 M16x28 [mm]
340 330 300 265 230 -0.096 272 275 122 209 23 26 331 457 185

Output shaft
U UY UZ VA VB
+ 0.0016
3.150 + 0.00039 3.362 0.866 7.09 3.15
A 80 3, A 80 4 UH + 0.04
80 + 0.01 85.4 22 180 80

Motor
Weight
AB C CB P
[lbs / kg]
5.59 31.87 35.65 7.68
A 80 3_S3 M3S 582 / 264
142 809.5 905.5 195
5.59 33.13 36.71 7.68
A 80 3_S3 M3L 597 / 271
142 841.5 932.5 195
7.60 37.38 41.67 10.16
A 80 3_S4 M4S 655 / 297
193 949.5 1058.5 258
7.60 37.38 41.67 10.16
A 80 3_S4 M4L 697 / 316
193 949.5 1058.5 258
7.60 38.76 42.66 10.16
A 80 3_S4 M4LC 714 / 324
193 984.5 1083.5 258
9.65 40.79 46.30 12.20
A 80 3_S5 M5S 785 / 356
245 1036 1176 310
9.65 42.52 48.03 12.20
A 80 3_S5 M5L 820 / 372
245 1080 1220 310
4.25 30.57 33.05 5.43
A 80 4_S1 M1S 545 / 247
108 776.5 839.5 138
4.25 31.52 33.92 5.43
A 80 4_S1 M1L 549 / 249
108 800.5 861.5 138
4.69 32.66 35.41 6.14
A 80 4_S2 M2S 560 / 254
119 829.5 899.5 156
5.59 34.35 38.13 7.68
A 80 4_S3 M3S 578 / 262
142 872.5 968.5 195
5.59 35.61 39.19 7.68
A 80 4_S3 M3L 593 / 269
142 904.5 995.5 195
7.60 39.86 44.15 10.16
A 80 4_S4 M4L 650 / 295
193 1012.5 1121.5 258
7.60 39.86 44.15 10.16 inch
A 80 4_S4 M4S 692 / 314 Dimensions are
193 1012.5 1121.5 258 mm
104
A 80 3 A 80 4 Shaft mount - NEMA C - face adapter
C

VA BA
NC
VB VB BB X N
DIA

OA U
J
BC

D
H
G

E FA FB NB

AC QB NA
A UZ MA

UY Output shaft MC Input shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
13.39 12.99 11.81 10.43 9.055 -0.0038 10.71 10.83 4.80 8.23 0.91 1.02 13.03 17.99 7.28
A 80 3, A 80 4 -0.050 M16x28 [mm]
340 330 300 265 230 -0.096 272 275 122 209 23 26 331 457 185

Output shaft
U UY UZ VA VB
+ 0.0016
3.150 + 0.00039 3.362 0.866 7.09 3.15
A 80 3, A 80 4 UH + 0.04
80 + 0.01 85.4 22 180 80

NEMA flange Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 547 / 248 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 549 / 249 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 551 / 250 N180TC 0.250 1.125 1.241
N210TC 8.996 7.250 8.500 0.551 0.216 571 / 259 N210TC 0.312 1.375 1.518
N250TC 13.780 7.250 8.500 0.551 0.216 591 / 268 N250TC 0.375 1.625 1.796
N280TC 13.780 9.000 10.500 0.551 0.216 592 / 268 N280TC 0.500 1.875 2.102
N320TC 17.717 11.000 12.500 0.669 0.216 657 / 298 N320TC 0.500 2.125 2.350

C
N56C N140TC N180TC N210TC N250TC N280TC N320TC
24.47 25.71 28.70 28.90 31.75
A 80 3 — —
621.5 653 729 734 806.5
26.20 26.20 26.95 28.19
A 80 4 — — —
665.5 665.5 684.5 716

inch
Dimensions are
mm
105
 Solid input / hollow output shaft A 80 3 A 80 4
C

VA B

VB VB BA

E BB

BC FV
KEY

FM
TAP

FU
OA U J

D DA
H
G

AC QB
A FA FB

UZ

UY Output Shaft FZ Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
13.39 12.99 11.81 10.43 9.055 -0.0038 10.71 10.83 4.80 8.23 0.91 1.02 13.03 17.99 7.28
A 80 3, A 80 4 -0.050 M16x28 [mm]
340 330 300 265 230 -0.096 272 275 122 209 23 26 331 457 185

Output shaft
U UY UZ VA VB
+ 0.0016
3.150 + 0.00039 3.362 0.866 7.09 3.15
A 80 3, A 80 4 UH + 0.04
80 + 0.01 85.4 22 180 80

Input shaft
FU FZ FV Key FM
+0
1.654 - 0.0006 1.772 4.331
A 80 3 HS +0 12 x 8 x 90 M12x28 [mm]
42 - 0.016 45 110
+0
A 80 4 NHS 1.000 - 0.0005 1.110 1.970 3/4 x 3/4 x 1 3/4 M8x19 [mm]

Weight
C [lbs / kg]
30.96
A 80 3 584 / 265
786.5
28.94
A 80 4 551 / 250
735

inch
Dimensions are
mm
106
A 80 3 A 80 4 Shaft mount - IEC B5 motor adapter
C

B A803_P225
6.063
VA 154
BA
(P63) N
NC
VB VB BB X N
DIA

45°
OA U
J
BC

NC
D
DIA
H
G

FA FB NB
E NB

AC QB NA NA
A UZ MA

UY Output shaft MC Input shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
13.39 12.99 11.81 10.43 9.055 -0.0038 10.71 10.83 4.80 8.23 0.91 1.02 13.03 17.99 7.28
A 80 3, A 80 4 -0.050 M16x28 [mm]
340 330 300 265 230 -0.096 272 275 122 209 23 26 331 457 185

Output shaft
U UY UZ VA VB
+ 0.0016
3.150 + 0.00039 3.362 0.866 7.09 3.15
A 80 3, A 80 4 UH + 0.04
80 + 0.01 85.4 22 180 80

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 547 / 248 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 547 / 248 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 549 / 249
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 551 / 250 P100, P112 8 28 31.3
P132 300 265 230 14 5 571 / 259 P132 10 38 41.3
P160 12 42 45.3
P160, P180 350 300 250 18 6 591 / 268
P180 14 48 51.8
P200 400 350 300 M16x25 7 615 / 279 P200 16 55 59.3
P225 450 400 350 18 6 657 / 298 P225 18 60 64.4

C
P63 P80 P100 P160
P132 P200 P225
P71 P90 P112 P180
23.70 24.09 25.53 27.72 28.70 30.49
A 80 3 —
602 612 648.5 704 729 774.5
25.41 26.18 26.57 28.01
A 80 4 — — —
645.5 665 675 711.5

inch
Dimensions are
mm

107
 Shaft mount, integral motor A 90 3 A 90 4
CB
C
AB B
VA BA

VB VB BB

OA U P
J
BC

D
H
G

E FA FB
AC UZ QB

UY Output Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
15.35 14.76 13.78 11.81 9.843 -0.0038 12.80 12.40 6.10 10.04 1.18 1.02 16.14 21.65 8.86
A 90 3, A 90 4 -0.050 M20x33 [mm]
390 375 350 300 250 -0.096 325 315 155 255 30 26 410 550 225

Output shaft
U UY UZ VA VB
+ 0.0018
3.543 + 0.00047 3.756 0.984 8.07 3.15
A 90 3, A 90 4 UH + 0.047
90 + 0.012 95.4 25 205 80

Motor
Weight
AB C CB P
[lbs / kg]
5.59 36.63 40.41 7.68
A 90 3_S3 M3S 926 / 420
142 930.5 1026.5 195
5.59 37.89 41.48 7.68
A 90 3_S3 M3L 941 / 427
142 962.5 1053.5 195
7.60 42.15 46.44 10.16
A 90 3_S4 M4S 999 / 453
193 1070.5 11795 258
7.60 42.15 46.44 10.16
A 90 3_S4 M4L 1041 / 472
193 1070.5 1179.5 258
7.60 43.52 47.42 10.16
A 90 3_S4 M4LC 1058 / 480
193 1105.5 1204.5 258
9.65 45.55 51.06 12.20
A 90 3_S5 M5S 1129 / 512
245 1157 1297 310
9.65 47.28 52.80 12.20
A 90 3_S5 M5L 1164 / 528
245 1201 1341 310
4.25 36.12 38.60 5.43
A 90 4_S1 M1S 906 / 411
108 917.5 980.5 138
4.25 37.07 39.47 5.43
A 90 4_S1 M1L 908 / 412
108 941.5 1002.5 138
4.69 38.21 40.96 6.14
A 90 4_S2 M2S 939 / 426
119 970.5 1040.5 156
5.59 39.90 43.68 7.68
A 90 4_S3 M3S 957 / 434
142 1013.5 1109.5 195
5.59 41.16 44.74 7.68
A 90 4_S3 M3L 972 / 441
142 1045.5 1136.5 195
7.60 45.41 49.70 10.16
A 90 4_S4 M4L 1030 / 467
193 1153.5 1262.5 258
7.60 45.41 49.70 10.16 inch
A 90 4_S4 M4S 1071 / 486 Dimensions are
193 1153.5 1262.5 258 mm
108
A 90 3 A 90 4 Shaft mount - NEMA C - face adapter
C

VA BA
NC
VB VB BB X N
DIA

OA U
J
BC

D
H
G

E FA FB NB

AC QB NA
A UZ MA

UY Output shaft MC Input shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
15.35 14.76 13.78 11.81 9.843 -0.0038 12.80 12.40 6.10 10.04 1.18 1.02 16.14 21.65 8.86
A 90 3, A 90 4 -0.050 M20x33 [mm]
390 375 350 300 250 -0.096 325 315 155 255 30 26 410 550 225

Output shaft
U UY UZ VA VB
+ 0.0018
3.543 + 0.00047 3.756 0.984 8.07 3.15
A 90 3, A 90 4 UH + 0.047
90 + 0.012 95.4 25 205 80

NEMA flange Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
N56C 6.496 5.875 4.500 0.394 0.196 908 / 412 N56C 0.188 0.625 0.710
N140TC 6.496 5.875 4.500 0.394 0.196 910 / 413 N140TC 0.188 0.875 0.964
N180TC 8.996 7.250 8.500 0.551 0.216 915 / 415 N180TC 0.250 1.125 1.241
N210TC 8.996 7.250 8.500 0.551 0.216 933 / 423 N210TC 0.312 1.375 1.518
N250TC 13.780 7.250 8.500 0.551 0.216 957 / 434 N250TC 0.375 1.625 1.796
N280TC 13.780 9.000 10.500 0.551 0.216 957 / 434 N280TC 0.500 1.875 2.102
N320TC 17.717 11.000 12.500 0.669 0.216 1041 / 472 N320TC 0.500 2.125 2.350

C
N56C N140TC N180TC N210TC N250TC N280TC N320TC
29.23 30.47 33.46 33.66 36.52
A 90 3 — —
742.5 774 850 855 927.5
31.75 31.75 32.50 33.74
A 90 4 — — —
806.5 806.5 825.5 857

inch
Dimensions are
mm
109
 Solid input / hollow output shaft A 90 3 A 90 4
C

VA B

VB VB BA

E BB

BC FV
KEY

FM
TAP

FU
OA U J

D DA
H
G

AC QB
A FA FB

UZ

UY Output Shaft FZ Input Shaft

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
15.35 14.76 13.78 11.81 9.843 -0.0038 12.80 12.40 6.10 10.04 1.18 1.02 16.14 21.65 8.86
A 90 3, A 90 4 -0.050 M20x33 [mm]
390 375 350 300 250 -0.096 325 315 155 255 30 26 410 550 225

Output shaft
U UY UZ VA VB
+ 0.0018
3.543 + 0.00047 3.756 0.984 8.07 3.15
A 90 3, A 90 4 UH + 0.047
90 + 0.012 95.4 25 205 80

Input shaft
FU FZ FV Key FM
+0
2.362 - 0.0007 2.520 5.512
A 90 3 HS +0 18 x 11 x 120 M16x36 [mm]
60 - 0.019 64 140
+0
A 90 4 NHS 1.000 - 0.0005 1.110 1.970 1/4 x 1/4 x 1 3/4 M8x19 [mm]

Weight
C [lbs / kg]
39.72
A 90 3 1025 / 465
1009
34.47
A 90 4 915 / 415
875.5

inch
Dimensions are
mm
110
A 90 3 A 90 4 Shaft mount - IEC B5 motor adapter
C
A903_P225
B A903_P250
6.063
VA 154
BA
(P63) N
NC
VB VB BB X N
DIA

45°
OA U
J
BC

NC
D
DIA
H
G

FA FB NB
E NB
AC QB NA NA
A UZ MA

UY Output shaft MC Input shaft

MB

Outline dimensions
A AC B BA BB BC D E FA FB G H J OA QB
-0.0020
15.35 14.76 13.78 11.81 9.843 -0.0038 12.80 12.40 6.10 10.04 1.18 1.02 16.14 21.65 8.86
A 90 3, A 90 4 -0.050 M20x33 [mm]
390 375 350 300 250 -0.096 325 315 155 255 30 26 410 550 225

Output shaft
U UY UZ VA VB
+ 0.0018
3.543 + 0.00047 3.756 0.984 8.07 3.15
A 90 3, A 90 4 UH + 0.047
90 + 0.012 95.4 25 205 80

IEC flange (mm) Hollow input shaft

Weight
N NA NB NC X MA MB MC
[lbs / kg]
P63 140 115 95 M8x19 4 906 / 411 P63 4 11 12.8
P71 160 130 110 M8x16 4.5 908 / 412 P71 5 14 16.3
P80 6 19 21.8
P80, P90 200 165 130 M10x12 4 910 / 413
P90 8 24 27.3
P100, P112 250 215 180 M12x16 4.5 915 / 415 P100, P112 8 28 31.3
P132 300 265 230 14 5 933 / 423 P132 10 38 41.3
P160 12 42 45.3
P160, P180 350 300 250 18 6 957 / 434
P180 14 48 51.8
P200 400 350 300 M16x25 7 961 / 436 P200 16 55 59.3
P225 450 400 350 18 6 1041 / 472 P225 18 60 64.4
P250 550 500 450 18 6 1047 / 475 P250 18 65 69.4

C
P63 P80 P100 P160
P132 P200 P225 P250
P71 P90 P112 P180
28.46 28.86 30.30 32.48 33.46 35.26 36.44
A 90 3 —
723 733 769.5 825 850 895.5 925.5
30.96 31.73 32.13 33.56 35.55
A 90 4 — — —
786.5 806 816 852.5 903

inch
Dimensions are
mm
111
 Foot mount A 10...A 90 (single shaft extension)

(V) VA VA V
UY
KEY KEY

U U Output Shaft

M M
TAP TAP

Output shaft (NUL, NUR inch series / UL, UR metric series)

Model U UY V VA Key M

2.480
NUL +0
A 10 1.000 -0.0005 1.110 2.000 1/4 x 1/4 x 1 3/4 M8x19 [mm]
NUR 63

2.874
NUL +0
A 20 1.250 -0.0006 1.360 2.500 1/4 x 1/4 x 2 5/32 M10x22 [mm]
NUR 73

3.268
NUL +0
A 30 1.375 -0.0006 1.510 2.750 5/16 x 5/16 x 2 3/8 M10x22 [mm]
NUR 83

3.661
NUL +0
A 41 1.625 -0.0006 1.790 3.250 3/8 x 3/8 x 2 7/8 M12x228 [mm]
NUR 93

4.646
NUL +0
A 50 2.000 -0.0007 2.220 4.000 1/2 x 1/2 x 3 3/4 M16x36 [mm]
NUR 118

4.921
NUL 2.625
+0
2.900 5.250 5/8 x 5/8 x 5 M20x42 [mm]
A 60 -0.0007
NUR 125
+0
3.150 -0.0009 3.346 5.118 6.024
UL 22x14x110 M20x42 [mm]
A 70
UR 80 +0
-0.022 85 130 153
+0
3.543 -0.0009 3.740 6.692 7.087
UL 25x14x160 M24x50 [mm]
A 80
UR 90 +0
-0.022 95 170 180
+0
3.937 -0.0009 4.173 8.267 8.070
UL 28x16x190 M24x50 [mm]
A 90
UR 100 +0
-0.022 106 210 205

inch
Dimension are
mm
112
Foot mount A 10...A 90 (double shaft extension)

V1 V
VA VA
(V) (V1) UY
KEY KEY

U U Output Shaft

M M
TAP TAP

Output shaft (NUD inch series / UD metric series)

Model U UY V V1 VA Key M

+0
2.480
A 10 NUD 1.000 -0.0005 1.110 2.080 2.000 1/4 x 1/4 x 1 3/4 M8x19 [mm]
63

2.874
+0
A 20 NUD 1.250 -0.0006 1.360 2.550 2.500 1/4 x 1/4 x 2 5/32 M10x22 [mm]
73

+0
3.268
A 30 NUD 1.375 -0.0006 1.510 2.800 2.750 5/16 x 5/16 x 2 3/8 M10x22 [mm]
83

+0
3.661
A 41 NUD 1.625 -0.0006 1.790 3.330 3.250 3/8 x 3/8 x 2 7/8 M12x228 [mm]
93

+0
4.646
A 50 NUD 2.000 -0.0007 2.220 4.060 4.000 1/2 x 1/2 x 3 3/4 M16x36 [mm]
118

4.921
+0
A 60 NUD 2.625 -0.0007 2.900 5.290 5.250 5/8 x 5/8 x 5 M20x42 [mm]
125
+0
3.150 -0.0009 3.346 5.118 5.118 6.024
A 70 UD 22x14x110 M20x42 [mm]
+0
80 -0.022 85 130 130 153
+0
3.543 -0.0009 3.740 6.692 6.692 7.087
A 80 UD 25x14x160 M24x50 [mm]
+0
90 -0.022 95 170 170 180
+0
3.937 -0.0009 4.173 8.267 8.267 8.070
A 90 UD 28x16x190 M24x50 [mm]
+0
100 -0.022 106 210 210 205

inch
Dimension are
mm
113
 Shaft mount with shrink disc A 10...A 90

VA VB

UB UC UD

N U UA

Output shaft (Inch series / Optional metric series)

T
Model é Ib × inù U UA UB UC UD VA VB N
ëê Nm ûú

128 1.260 1.181 1.417 3.051 1.417 2.362 4.055 3.346

A 10
14.5 32 30 36 77.5 36 60 103 85

128 1.457 1.378 1.654 3.524 1.614 2.756 4.547 3.937

A 20
14.5 37 35 42 89.5 41 70 115.5 100

128 1.654 1.575 1.969 3.760 1.890 3.150 4.941 3.937

A 30
14.5 42 40 50 95.5 48 80 125.5 100

128 1.850 1.772 2.047 4.862 1.909 3.661 5.819 5.315

A 41
14.5 47 45 52 123.5 48.5 93 147.8 195

310 2.244 2.165 1.890 6.142 2.441 4.488 7.051 7.283

A 50
35 57 55 48 156 62 114 179.1 185

310 2.835 2.756 1.969 7.008 2.638 4.921 7.461 7.283

A 60
35 72 70 50 178 67 125 189.5 185

310 3.228 3.150 3.622 6.811 3.543 6.024 8.366 8.268

A 70
35 82 80 92 173 90 153 212.5 210

611 3.622 3.543 4.016 8.504 3.937 7.087 9.764 9.055

A 80
69 92 90 102 216 100 180 248 230

611 4.016 3.937 3.150 12.638 2.756 8.071 11.063 9.843

A 90
69 102 100 80 321 70 205 281 250

inch
Dimension are
mm
114
Flange options for A 10...A 60

C B A

AJ BE GA AJ BE GA AJ BE GA 1 2

BD AK BD AK BD AK

BF BF BF
DIA DIA DIA
VD
VD
VD

Flange
AJ AK BD BE BF GA VD
-0.0014
5.118 4.331 -0.0028 6.299 0.118 0.354 0.394 3.602
A 10 -0.036
130 110 -0.071 160 3 9 10 91.5
-0.0014
5.118 4.331 -0.0028 6.299 0.118 0.354 0.394 3.602
A 20 -0.036
130 110 -0.071 160 3 9 10 106
-0.0014
5.118 4.331 -0.0028 6.299 0.118 0.354 0.394 4.567
A 30
A
-0.036
130 110 -0.071 160 3 9 10 116
-0.0017
8.465 7.087 -0.0033 9.843 0.157 0.433 0.512 5.020
A 41 -0.043
215 180 -0.083 250 4 14 13 127.5
-0.0020
10.433 9.055 -0.0038 11.811 0.157 0.433 0.630 6.299
A 50 -0.050
265 230 -0.096 300 4 14 16 160
-0.0020
10.433 9.055 -0.0038 11.811 0.157 0.433 0.630 6.692
A 60 -0.050
265 230 -0.096 300 4 14 16 170
-0.0017
6.496 5.118 -0.0033 7.874 0.138 0.433 0.433 3.602
A 10 -0.043
165 130 -0.083 200 3.5 11 11 91.5
-0.0017
6.496 5.118 -0.0033 7.874 0.138 0.433 0.433 4.173
A 20 -0.043
165 130 -0.083 200 3.5 11 11 106
-0.0017
6.496 5.118 -0.0033 7.874 0.138 0.433 0.433 4.567
A 30 -0.043
165 130 200 3.5 11 11 116
B
-0.083
-0.0020
10.433 9.055 -0.0038 11.811 0.157 0.551 0.630 5.020
A 41 -0.050
265 230 -0.096 300 4 14 16 127.5
-0.0020
11.811 9.843 -0.0039 13.780 0.197 0.709 0.709 6.299
A 50 -0.050
300 250 -0.098 350 5 18 18 160
-0.0020
11.811 9.843 -0.0039 13.780 0.197 0.709 0.709 6.692
A 60 -0.050
300 250 -0.098 350 5 18 18 170
-0.0017
8.465 7.087 -0.0033 9.843 0.157 0.551 0.512 3.602
A 10 -0.043
215 180 -0.083 250 4 14 13 91.5
-0.0017
8.465 7.087 -0.0033 9.843 0.157 0.551 0.512 4.173
A 20 -0.043
215 180 -0.083 250 4 14 13 106
-0.0017
8.465 7.087 -0.0033 9.843 0.157 0.551 0.512 4.567
A 30
C
-0.043
215 180 -0.083 250 4 14 13 116
-0.0020
11.811 9.843 -0.0038 13.780 0.197 0.709 0.709 5.020
A 41 -0.050
300 250 -0.096 350 5 18 18 127.5
-0.0022
13.780 11.811 -0.0043 15.748 0.197 0.709 0.787 6.299
A 50 -0.056
350 300 -0.108 400 5 18 20 160
-0.0022
13.780 11.811 -0.0043 15.748 0.197 0.709 0.787 6.692
A 60 -0.056
350 300 -0.108 400 5 18 20 170

inch
Dimensions are
mm

115
 Flange options for A 70...A 90
B A

AJ BE GA AJ BE GA 1 2

BD AK BD AK

BF BF
DIA DIA
VD
VD

Flange
AJ AK BD BE BF GA VD
-0.0024
15.748 13.780 -0.0047 17.717 0.197 0.709 0.866 8.661
A 70 -0.062
400 350 -0.119 450 5 18 22 220

A
-0.0024
15.748 13.780 -0.0047 17.717 0.197 0.709 0.866 9.843
A 80 -0.062
400 350 -0.119 450 5 18 22 250
-0.0027
19.685 17.717 -0.0052 21.654 0.197 0.709 0.945 11.024
A 90 -0.068
500 450 -0.131 550 5 18 24 280
-0.0027
19.685 17.717 -0.0052 21.654 0.197 0.709 0.945 8.661
A 70
B
-0.068
500 450 -0.131 550 5 18 24 220
-0.0027
19.685 17.717 -0.0052 21.654 0.197 0.709 0.945 9.843
A 80 -0.068
500 450 -0.131 550 5 18 24 250

inch
Dimensions are
mm
116
2.17 TORQUE ARM

DD DE L LA LB Y YA YB

5.433 4.252 5.827 4.646 2.362 0.787 0.394 1.181

A 10
138 108 148 118 60 20 10 30

5.827 4.646 6.575 5.394 2.362 0.787 0.394 1.181

A 20
148 118 167 137 60 20 10 30

6.693 5.315 7.283 5.906 2.756 0.984 0.787 1.575

A 30
170 135 185 150 70 25 20 40

7.559 6.181 9.252 7.874 2.756 0.984 0.787 1.575

A 40
192 157 235 200 70 25 20 40

9.646 7.874 11.614 9.843 3.543 1.575 1.260 2.205

A 50
245 200 295 250 90 40 32 56

10.630 8.858 13.583 11.811 3.543 1.575 1.260 2.205

A 60
270 225 345 300 90 40 32 56

13.150 11.380 11.614 9.843 3.543 1.575 1.260 2.205

A 70
334 289 295 250 90 40 32 56

16.614 14.055 14.370 11.811 5.118 2.362 1.654 3.071

A 80
422 357 365 300 130 60 42 78

18.700 16.142 16.338 13.780 5.118 2.362 1.654 3.071

A 90
475 410 415 350 130 60 42 78

Torque arm comes complete with fasteners

inch
Dimensions are
mm

117
118
3.0 BONFIGLIOLI ELECTRIC MOTORS

119
 (C1)
3.1 GENERAL INFORMATION
Canada CSA C22.2 N° 100
Great Britain BS5000 / BS 4999
BONFIGLIOLI RIDUTTORI three-phase AC induction Germany DIN VDE 0530
motors and brake motors are designed for continuous Australia AS 1359
operation, IEC dimensional standard and comply electri- Belgium NBNC 51 - 101
cally with all relevant standards including NEMA MG1. Norway NEK – IEC 34
France NF C 51
They are supplied either integral (M type) to a
Austria OEVE M 10
BONFIGLIOLI gear unit or flanged design (BN type).
Switzerland SEV 3009
The motors also comply with national standards Netherlands NEN 3173
adapted to IEC 60034-1 as charted along side. Sweden SS 426 01 01

Abbreviations and units Conversion table for commonly

used metric – imperial units
Symb. U.m. Description Length
1 in = 25.40 mm = 0.0254 m
cos j – Power factor = 0.3048 m
1 ft = 304.8 mm
h – Efficiency = 0.9144 m
1 yd = 914.4 mm
fm – Intermittence adjustment factor
ft – Ambient temperature factor Area
I – Cyclic duration factor 1 in2 = 645.16 mm2 = 0.645´10-3 m2
ln [A] Rated current 1 ft2 = 92.9´103 mm2 = 92.9´ 103 m2
1 yd2 = 836´103 mm2 = 0.8361 m2
ls [A] Locked rotor current
Jc [Ib·ft2] Load inertia Volume
Jm [Ib·ft2] Motor inertia
1 in3 = 16.4´10-3 dm3 = 16.4´10-6 m3
n [rpm] Speed 1 ft3 = 28.32 dm3 = 28.3´10-3 m3
Kc – Torque factor
Kd – Load factor Force – Weight
Kj – Inertia factor 1 lbm = 2.2046 Kg
Tb [lb·in] Brake torque 1 lbf = 4.4482 N
Tn [lb·in] Motor rated torque
Torque
Ta [lb·in] Mean starting torque
1 lb in = 0.1129 Nm
Tk [lb·in] Breakdown torque 1 lb ft = 1.3558 Nm
TL [lb·in] Load torque
Ts [lb·in] Locked rotor torque Power
Pb [W] Power absorbed by brake coil 1 hp = 0.7457 kW
Pn [W] Rated power output
Moment of inertia
t1 [ms] Brake release time
1 lb ft2 = 4.214´10-2 Kg m2
t1s [ms] Shorter brake release time 2
1 lb in s = 1.12985´10-1 Kg m2
t2 [ms] Brake reaction time 2
1 lb ft s = 1.35582 Kg m2
t2c [ms] Faster reaction time
ta [°C/ °F] Ambient temperature Pressure – stress
tf [min] Operating time at constant load 1 lb/in2 = 6.89´10-3 N/mm2
tr [min] Rest time
2
1 lb/ft = 47.88 N/m2
W [Ib•ft] Brake work between two successive
adjustments Temperature
5
Wmax [Ib•ft] Max permissible brake work t [°F] = x [ t - 32] [°C]
Z [1/h] Permissible starts per hour 9
Z0 [1/h] Permissible starts per hour (un- æ 9 x T + 32 ö [°F]
T [°C] = ç ÷
loaded, I=50%) è 5 ø

120
3.2 MOTOR ORDERING NUMBERS

MOTOR BRAKE

M 2SA 4 230/460-60 IP54 CLF ..... W FD 15 R SB 220 SA ....

OPTIONS

BRAKE SUPPLY

AC/DC RECTIFIER
NB, NBR, SB, SBR

BRAKE HAND RELEASE (optional)

R, RM

BRAKE TORQUE [specify Nm!]

[1 ft • Ib = 1.356 Nm]

BRAKE TYPE
FD (DC brake)
FA (AC brake)

TERMINAL BOX
W (default), N, S, E

MOUNTING
blank for compact motor
B5 for IEC motor

INSULATION CLASS
CL F default

DEGREE OF PROTECTION
IP 55 standard (IP 54 standard for brake motors)

VOLTAGE - FREQUENCY

NUMBER OF POLES

MOTOR FRAME SIZE

TYPE OF MOTOR

121
US power mains voltages and the corresponding rated
voltages to be specified for the motor are indicated in
CUS
the following table: Motors for USA and Canada
(C2)

Frequency Mains voltage Vmot

BN and M motors are available in NEMA Design C con-
figuration (concerning electrical characteristics), certified
208 V 200 V
to CSA (Canadian standard) C22.2 No. 100 and UL
240 V 230 V (Underwriters Laboratory) UL 1004. Name plate in-
60 Hz cludes the cCSAus mark (voltage £ 600V), in this case,
480 V 460 V
please specify option CUS.
600 V 575 V

Motors with YY/Y connection (e.g. 230/460-60;

220/440-60) feature, as standard, a 9-stud terminal
board. 3.3 MECHANICAL
For DC brake motors type BN_FD, the rectifier is fed
with 1-phase 230V a.c., factory pre-wired in the motor CHARACTERISTICS
terminal box as standard.

IP..
Brake power supply for brake motors is as follows:
(C3)
Enclosures

BN_FD Motors are provided as totally enclosed fan-cooled

M_FD
(TEFC) according to NEMA MG1 1-26-2 1998 and they
are designed for IP 55 (IP 54 for brake motors) degree
Wired to terminal box 1~230V a.c.
of protection in accordance with NEMA MG1- 5 / IEC
60034-5 Standards.
BN_FA
Higher degree of protection (IP 56, or IP 55 for brake
M_FA
motors) is available on request.
Specify The following table provides an overview of the avail-
able degree of protection.
Separate power supply Regardless of the protection class specified on order,
230SA
230V D - 60Hz motors to be installed outdoors require protection
against direct sunlight and in addition – when they are to
Separate power supply be installed with the shaft downwards – a drip cover to
460SA
460V Y - 60Hz
keep out water and solid matter (option RC).

(C5)
Tolerances
IP 54 IP 55 IP 56
As per the IEC standards applicable the tolerances here n.a. standard at request
after apply to the following quantities.
BN_FD M_FD
standard at request n.a.
BN_FA M_FD

(C4)
-0.15 (1 - h) P £ 75 hp Efficiency
-(1 - cosj)/6 min 0.02 max 0.07 Power factor
±20% * Slip
Cooling
+20% Locked rotor current
-15% +25% Locked rotor torque The motors are self ventilated (IEC 411 / NEMA MG1-6)
-10% Max. torque and are equipped with a plastic fan working in both di-
* ± 30% for motors with Pn < 0.75 hp rections.

122
The motors must be installed allowing sufficient space Values refer to measures with freely suspended motor
between fan cowl and the nearest wall to ensure free air in unloaded conditions.
intake and allow access for maintenance purposes on
motor and brake, if supplied.
Independent, forced air ventilation (IEC 416 / NEMA
MG1-6) can be supplied on request (option U1). Winding connection and motor
This solution enables to increase the motor duty factor
when driven by an inverter and operating at reduced terminal box
speed.
Standard terminal board has 9 studs for YY-Y dual-volt-
age winding and 6 studs for star/delta winding configu-
ration (single-speed motors).
Direction of rotation An earth terminal located in the terminal box is provided
as standard on all motors.
Rotation is possible in both directions. If terminals U1,
For DC brake motors, the AC/DC rectifier is supplied in
V1, and W1 are connected to line phases L1, L2 and L3,
the terminal box and it is provided with adequately con-
clockwise rotation (looking from drive end) is obtained.
nected terminals.
For counterclockwise rotation, switch two phases.
All connections must be carried out according to the dia-
grams inside the terminal box or in the instruction
manual.

Noise
Cable entry
(C7)
Noise levels, measured using the method prescribed by
ISO 1680 Standards, are within the maximum levels Cable entry Max cable diam.
specified by Standards CEI EN 60034-9. (metric thread) [mm]

BN 63 M 05 2 x M20 13

BN 71 M1 2 x M25 17
Vibrations and balancing
BN 80 - BN 90 M2 2 x M25 17

Rotor shafts are balanced with half key fitted and fall 2 x M32 21
BN 100 M3
within the vibration class N, as per Standard CEI EN
2 x M25 17
60034-14.
If a further reduced noise level is required improved bal- 2 x M32
ancing can be optionally requested (class N). BN 112 - 17
2 x M25
Table below shows the value for the vibration velocity
for standard (N) and improved (R) balancing. BN 132...BN 160MR M4 4 x M32 21

(C6) BN 160M...BN 200L M5 2 x M40 29

Vibration Angular Limits of the vibration velocity

class velocity
[mm/s]
Bearings
BN 56…BN 132 BN 160MR…BN 200
n [rpm] M05…M4 M5
Life lubricated preloaded radial ball bearings are used,
types are shown in the chart here under.
N 600 £ n £ 3600 1.8 2.8
Calculated endurance lifetime L10, as per ISO 281, in
unloaded condition, exceeds 40000 hrs.
600 £ n £ 1800 0.71 1.12
R DE = drive end
1800 < n £ 3600 1.12 1.8 NDE = non drive end

123
(C8) (C10)

DE NDE Low Voltage High Voltage

M, M_FD, M_FA M M_FD, M_FA
230V - 60Hz 460V - 60Hz
M05 6004 2Z C3 6201 2Z C3 6201 2RS C3

M1 6004 2Z C3 6202 2Z C3 6202 2RS C3 200V - 50Hz 400V - 50Hz

M2 6007 2Z C3 6204 2Z C3 6204 2RS C3

Single-Speed / Dual-Voltage
M3 6207 2Z C3 6206 2Z C3 6206 2RS C3
Low Voltage YY High Voltage Y
M4 6309 2Z C3 6208 2Z C3 6208 2RS C3

M5 6309 2Z C3 6209 2Z C3 6209 2RS C3

U2 V2 W2

T4 T5 T6 T4 T5 T6
U2 V2 W2
(C9) U5 V5 W5 U5 V5 W5
T7 T8 T9 T7 T8 T9

DE NDE U1
T1
V1
T2
W1
T3
U1
T1
V1
T2
W1
T3

BN, BN_FD,
BN BN_FD, BN_FA L1 L2 L3 L1 L2 L3
BN_FA

BN 56 6201 2Z C3 6201 2Z C3 -

BN 63 6201 2Z C3 6201 2Z C3 6201 2Z C3

BN 71 6202 2Z C3 6202 2Z C3 6202 2Z C3

BN 80 6204 2Z C3 6204 2Z C3 6204 2Z C3

(C11)
BN 90 6205 2Z C3 6205 2Z C3 6205 2Z C3

BN 100 6206 2Z C3 6206 2Z C3 6206 2Z C3 Low Voltage High Voltage

BN 112 6306 2Z C3 6306 2Z C3 6306 2Z C3

200V - 50Hz 346V - 50Hz
BN 132 6308 2Z C3 6308 2Z C3 6308 2Z C3
208V - 60Hz 360V - 60Hz
BN 160MR 6309 2Z C3 6308 2Z C3 6308 2Z C3

BN 160M/L 6309 2Z C3 6309 2Z C3 6309 2Z C3 220V - 50Hz 380V - 50Hz

BN 180M 6210 2Z C3 6309 2Z C3 6309 2Z C3 230V - 50Hz 400V - 50Hz

BN 180L 6310 2Z C3 6310 2Z C3 6310 2Z C3
240V - 50Hz 415V - 50Hz
BN 200L 6312 2Z C3 6310 2Z C3 6310 2Z C3
330V - 60Hz 575V - 60Hz

Single-Speed / Dual-Voltage

3.4 ELECTRICAL Low Voltage D High Voltage Y

CHARACTERISTICS
Voltage W2 U2 V2
T6 T4 T5
T6 T4 T5
W2 U2 V2

Motors can operate on any voltage within the range of T1

U1 V1
T2 T3
W1 U1
T1
V1
T2
W1
T3
200 – 690 Volts. Voltage to be <600 V for CSA/UL motors.
Voltage values available as standard are 230/460V-60
Hz and 575V-60Hz. L1 L2 L3 L1 L2 L3
Other voltage values may be available on request.

124
 (C13)
Rated horsepower
CL H
Motor outputs shown in this catalogue are based on 360°F
CL F 360°F - Hot spot
continuous operation at 40 °C [100 °F] ambient temper- 310°F allowance

ature and maximum elevation not exceeding 3300 feet 330°F

310°F
(1000 m) above the sea level. 293°F
Motors can operate at higher ambient temperatures
with output adjusted in accordance with the chart (C12)
here below. Temperature
rise allowed

(C12)
105°F 105°F
Max. ambient
Ambient temperature
100 115 120 130 140
temperature [°F]

Power output as a Standard Option

100% 95% 90% 85% 80%
% of rated power

Should a derating factor higher than 15% apply, contact Types of duty
our Technical Service.

Unless otherwise indicated, the power rating of motors

specified in the catalogue refers to continuous duty S1.
For motors used under conditions other than S1, the
type of duty required is definied with reference to CEI
EN 60034-1 Standards.
Insulation class
In particular, for intermittent duties type S2 and S3,
power can be adjusted with respect to continuous duty
through multipliers listed in table (C14) applicable to sin-
CL F gle speed motors.

Bonfiglioli motors use class F insulating materials P (S2...S8)

(enamelled wire, insulators, impregnation resins) as fm =
P (S1)
compared to the standard motor.
(C14)

Duty
CL H
S2 S3 * S4 - S8
Motors manufactured in higher insulation class H are
available at request.
Cycle duration Cyclic duration
In standard motors, the stator windings temperature rise (min) factor (I)
normally stays below the 80 K limit corresponding to
class B over temperature. Consult
10 30 60 25% 40% 60% factory
A careful selection of insulating components makes the
motors compatible with tropical climates and normal vi-
bration. fm 1.35 1.15 1.05 1.25 1.15 1.1
For applications involving the presence of aggressive
chemicals or high humidity, contact Bonfiglioli Engi- * Cycle duration must, in any event, be equal to or less than 10 min-
neering for assistance with product selection. utes; if this time is exceeded, please contact our Technical Service.

125
 (C15)
Cycle duration factor:
tf
I= x 100
tf + tr 1.2

tf = operating time at constant load 1

tr = rest time
0.8

M / MN
0.6

Limited duration duty S2 0.4

0.2

This type of duty is characterized by operation at con- 0

0 10 20 30 40 50 60 70 80 90 100
stant load for a limited time, which is shorter than the
[Hz]
time required to reach thermal equilibrium, followed by a
rest period of sufficient duration to restore ambient tem- Separate cooling Self cooling
perature in the motor.

Periodical intermittent duty S3 Table (C16) reports the mechanical limit speed for mo-
tor operation above rated frequency:

This type of duty is characterized by a sequence of (C16)

identical operation cycles, each including a constant
n [rpm]
load operation period and a rest period.
For this type of duty, the starting current does not signifi- 2p 4p 6p
cantly influence overtemperature.
£ BN 112 M05…M3 5200 4000 3000

BN 132...BN 200L M4, M5 4500 4000 3000

Inverter-driven motors
Above rated speed, motors generate increased me-
The electric motors of series BN and M may be used in chanical vibration and fan noise. Class R rotor balancing
combination with PWM inverters with rated voltage at is highly recommended in these applications. Installing a
transformer input up to 500 V.Standard motors use a separate supply fan cooling may also be advisable.
phase insulating system with separators, class 2 enam- Indipendent fan cooling and brake (if fitted) must always
elled wire and class H impregnation resins (1600V be connected direct to mains power supply.
peak-to-peak voltage pulse capacity and rise edge ts >
0.1µs at motor terminals). Table (C14) shows the typical
torque/speed curves referred to S1 duty for motors with
base frequency fb = 60 Hz. Permissible starts per hour Z
Because ventilation is somewhat impaired in operation
at lower frequencies (approx. 30 Hz), standard motors
with incorporated fan (IC411) require adequate torque The rating charts of brakemotors lend the permitted
derating or - alternately - the addition of a separate number of starts Z0, based on 50% intermittence and for
supply fan cooling. unloaded operation.
Above base frequency, upon reaching the maximum The catalogue value represents the maximum number
output voltage of the inverter, the motor enters a of starts per hour for the motor without exceeding the
steady-power field of operation, and shaft torque drops rated temperature for the insulation class F.
with ratio (f/fb). To give a practical example for an application character-
As motor maximum torque decreases with (f/fb)2, the al- ized by inertia Jc, drawing power Pr and requiring mean
lowed overloading must be reduced progressively. torque at start-up TL the actual number of starts per hour

126
for the motor can be calculated approximately through meaning that they are applied by spring-action in the
the following equation: event of a power failure.

(C18)
Z x Kc x Kd
Z= 0
KJ

where:
Jm + Jc
KJ = =inertia factor
Jm
Ta - TL
Kc = = torque factor
Ta

Kd = load factor (see table C17)

(C17)

Key:
 brake disc
‚ disc carrier
ƒ pressure plate
„ brake coil
… motor rear shield
† brake springs

When power is disconnected, the springs push the ar-

mature plate against the brake disc. The disc becomes
trapped between the armature plate and motor shield
and stops the shaft from rotating.
When the coil is energized, a magnetic field attracts the
If actual starts per hour is within permitted value (Z) it armature plate, so that the brake disc – which is integral
may be worth checking that braking work is compatible with the motor shaft – is released.
with brake (thermal) capacity Wmax also given in table
(C22) and dependent on the number of switches (s/h).
Most significant features

• High braking torques (normally T2 Tn), braking

torque adjustment.
3.5 BRAKE MOTORS • Steel brake disc with double friction lining (low-wear,
asbestos-free lining).
• Hexagonal socket head on motor shaft end (N.D.E.)
Operation for manual rotation (not compatible with options PS,
RC, TC, U1, U2, EN1, EN2, EN3).

Versions with incorporated brake use spring-applied DC

• Manual release lever.
(FD option) or AC (FA option) brakes. • Corrosion-proof treatment on all brake surfaces.
All brakes are designed to provide fail-safe operation, • Class F insulation

127
3.6 DC BRAKE MOTORS TYPE BN_FD

Frame sizes: BN 63 … BN 200L

(C19)

IP 54 (DEFAULT FOR BRAKE MOTORS) IP 55 (OPTIONAL ON BRAKE MOTORS)

Direct current electromagnetic brake bolted onto motor

Protection class
shield. Preloading springs provide axial positioning of
magnet body. Standard protection class is IP54.
Brake disc slides axially on steel hub fitted onto motor Brake motor FD is also available in protection class IP
shaft with anti-vibration spring. 55, which incorporates the following variants:
Brake torque factory setting is indicated in the corre-
 V-ring at N.D.E. of motor shaft
sponding motor rating charts.
Braking torque may be modified by changing the type ‚ dust and water-proof rubber boot
and/or number of springs. ƒ stainless steel shim placed between motor shield
At request, motors may be equipped with manual re- and brake disc
lease lever with automatic return (R) or system for hold- „ stainless steel hub
ing brake in the released position (RM). … stainless steel brake disc
See table (C33) for available release lever locations.
FD brakes ensure excellent dynamic performance with
low noise. DC brake operating characteristics may be
optimized to meet application requirements by choosing
from the various rectifier/power supply and wiring con-
nection options available.
FD brake power supply
A rectifier housed into the terminal box feeds the DC
brake coil. Wiring connection across rectifier and brake
coil is performed at the factory.
On single-speed motors, rectifier is pre-wired to the mo-
tor terminal board.
Rectifier standard power supply voltage VB is as indi-
cated in the following table (C20), regardless of mains
frequency:

128
(C20)

2, 4, 6 P 1 speed

BN_FD / M_FD
brake connected to terminal separate power
Vmot ± 10% VB ± 10% board power supply supply
3~ 1~

BN 63…BN 200 M05...M5 230/460 V – 60 Hz 230 V standard specify VB SA or VB SD

The diode half-wave rectifier (Vdc » 0,45 x Vac) is avail- Rectifiers NBR or SBR are available for applications re-
able in versions NB, SB, NBR e SBR, as detailed in the quiring quick brake release response.
table (C21). Rectifier SB with electronic energizing con- These rectifiers complement the NB and SB types as
trol over-energizes the electromagnet upon power-up to their electronic circuit incorporates a static switch that
cut brake release response time and then switches to de-energizes the brake quickly in the event voltage is
normal half-wave operation once the brake has been re- missing.
leased. This arrangement ensures short brake release response
Use of the SB rectifier is mandatory in the event of: time with no need for additional external wiring and con-
tacts.
- high number of operations per hour
Optimum performance of rectifiers NBR and SBR is
- reduced brake release response time achieved with separate brake power supply.
- brake is exposed to extreme thermal stress Available voltages: 230V ± 10%.

(C21)

Brake
Standard At request

BN 63 M05 FD 02

FD 03 SB,
BN 71 M1 t1 t2

FD 53

M2 FD 04 NB SBR,
BN 80
t1 t2 t1s t2r *
BN 90S — FD 14

BN 90L — FD 05 NBR
t1 t2r *
BN 100 FD 15
M3
— FD 55

BN 112 — FD 06S

BN 132...160MR M4 FD 56 SB SBR
t1s t2 t1s t2r *
BN 160L - BN 180M M5 FD 06

BN 180L - NM 200L — FD 07

(*) t2c < t2r < t2

129
FD brake technical specifications

The table (C22) shows the technical specifications of DC brakes type FD.

(C22)

Brake torque Wmax per each brake

Brake Release Braking W P
Tb [lb·in] operation

Springs t1 t1s t2 t2c [lb·ft]

6 4 2 [ms] [ms] [ms] [ms] 10 c/h 100 c/h 1000 c/h [lb·ftx106] [W]

FD02 — 31 15 30 15 80 9 3300 1050 130 11 17

FD03 44 31 15 50 20 100 12
5200 1400 170 18 24
FD53 66 44 22 60 30 100 12

FD04
133 88 44 80 35 140 15 7400 2300 260 27 33
FD14

FD05 354 230 115 130 65 170 20

FD15 354 230 115 130 65 170 20 13300 3300 370 37 45

FD55 487 327 159 — 65 170 20

FD06S 831 354 177 — 80 220 25 15000 3500 400 52 55

FD56 664 327 90 150 20

— — 21500 5500 600 59 65
FD06 885 443 100 150 20

FD07 1328 885 443 — 120 200 25 29500 6900 750 96 65

FD08* 2200 1770 1500 — 140 350 30 44500 10300 1100 170 100

FD09** 3540 2650 1770 — 200 450 40 51500 7600 1250 170 120

* brake torque values obtained with 9, 7 and 6 springs, ** brake torque values obtained with 12, 9 and 6
respectively springs, respectively

Key:
t1 = brake release time with half-wave rectifier Wmax = max energy per each brake operation
t1s = brake release time with over-energizing rectifier W = braking energy between two successive
t2 = brake engagement time with AC line disconnect air gap adjustments
and separate power supply Pb = brake power absorption at normal ambient
t2c = brake engagement time with AC and DC line temperature
disconnect. Tb = static braking torque (±15%)
Values for t1, t1s, t2, t2c indicated in the tab. (C22) [s/h] = starts per hour
are referred to brake set at maximum torque,
medium air gap and rated voltage

130
FD brake connections
Because the load is of the inductive type, brake con-
On standard single-speed motors, the rectifier is con- trol and DC line switch must use contacts from the
nected to the motor terminal board at the factory. usage class AC-3 to IEC 60947-4-1.

(C23) (C24) (C25) (C26)

Coil Coil Coil Coil

Brake supply from motor Separate power supply to Brake coil energized from Separate power supply to
terminals and A.C. line dis- brake coil and A.C. line motor terminals, both A.C. brake coil. Both A.C. and
connect. Longer stop time disconnect. and D.C. line switch off. D.C. line disconnect.
t2, dependent on motor Stopping time is independ- Rapid stopping time, t2c. Rapid stopping time to t2c
time constants. Use when ent on motor. See table See table C22 value, see table C22
no particular braking per- C22
formance is required.

131
3.7 AC BRAKE MOTORS TYPE BN_FA
Frame sizes: BN 63 … BN 180M

(C27)

IP 54 IP 55

Electromagnetic brake operates from three-phase alter- Degree of protection

nated current power supply and is bolted onto motor
rear shield. Preloaded springs provide axial positioning
of the magnet body. Standard degree of protection is IP54.
Steel brake disc slides axially on steel hub fitted onto Brake motor BN_FA is also available with degree of pro-
motor shaft with anti-vibration spring. tection IP 55, which incorporates the following variants:
Brake torque factory setting is indicated in the corre-
sponding motor rating charts. - V-ring at N.D.E. of motor shaft
Spring preloading screws provide stepless braking - water-proof rubber grommet
torque adjustment.
- O-ring
Torque adjustment range is 30% TbMAX < Tb < TbMAX
(where TbMAX is maximum braking torque as shown in
tab. (C29).
Thanks to their high dynamic characteristics, FA brakes
are ideal for heavy-duty applications as well as applica-
tions requiring frequent stop/starts and fast response
time.
Motors may be equipped with manual release lever with
automatic return (R) at request. See table (C33) for
available lever locations.

132
FA brake power supply
Depending on motor voltage the brake may require the diagram below. Special voltages in the 24...690 V range
supply voltage to be specified, or not, as detailed in the may be available on request.
(C28)
Motor voltage - Vmot Brake voltage - VB Specify Brake wiring scherme
Motor terminal board Auxiliary terminal board W2
T6
U2
T4
V2
T5

230 D - 60 Hz 230SA D Connected

U1
T1
V1
T2
W1
T3

230/460 V YY/Y T4
U2
T5
V2
T6
W2
W2
T6
U2
T4
V2
T5
L1 L2 L3

60 Hz U5
T7
V5
T8
W5
T9 T6
W2
T4
U2
T5
V2
U1 V1 W1

460 Y - 60 Hz 460SA U1 V1 W1
T1 T2 T3 Y Connected
U1
T1
V1
T2
W1
T3

T1 T2 T3
L1 L2 L3

Motor terminal board Brake

330/575 V D/Y 330/575 V D/Y not W2 U2 V2

T6 T4 T5
60 Hz 60 Hz required U1 V1 W1
T1 T2 T3

Technical specifications of FA brakes

(C29)
Brake Brake torque Release Braking Wmax W Pb

Tb t1 t2 [lb·ft]
6
[lb·in] [ms] [ms] 10 s/h 100 s/h 1000 s/h [lb·ftx10 ] [VA]
FA 02 31 4 20 4500 1400 180 15 60
FA 03 66 4 40 7000 1900 230 25 80
FA 04
133 6 60 10000 3100 350 30 110
FA 14

FA 05
354 8 90 18000 4500 500 50 250
FA 15

FA 06S 530 16 120 20000 4800 550 70 470

FA 06 663 16 140 29000 7400 800 80 550

FA 07 1328 16 180 40000 9300 1000 130 600

FA 08 2200 20 200 60000 14000 1500 230 1200

Key:
Tb = max static braking torque (±15%) Pb = power drawn by brake at 20° (50 Hz)
t1 = brake release time [s/h] = starts per hour
t2 = brake engagement time
Wmax = max energy per brake operation (brake thermal
capacity) NOTE
W = braking energy between two successive air gap Values t1 and t2 in the table refer to a brake set at rated
adjustments torque, medium air gap and rated voltage.

133
 The availability for the two lever options is charted here
3.8 - BRAKE RELEASE SYSTEMS below:

Spring-applied brakes type FD and FA may be

equipped with optional manual release devices. These
are typically used for manually releasing the brake be-
(C32)
fore servicing any machine or plant parts operated by
the motor. R RM

BN_FD BN 63...BN 200 BN 63...BN 160MR

R
M_FD M 05...M 5 M 05...M 4LC
(C30)
BN_FA BN 63...BN 180M
n.a.
M_FA M 05...M 5

Release lever arrangement

Unless otherwise specified, the release lever is located

90° away from the terminal box – identified by letters
[AB] in the diagram below – in a clockwise direction on
A return spring brings the release lever back in the origi- both options R and RM.
nal position. Alternative lever positions [AA], [AC] and [AD] are also
possible when the corresponding option is specified:

RM (C33)
(C31)

AA
AC
AD

Fly-wheel data (F1)

On motors type BN_FD, it the option RM is specified, The table below shows values of weight and inertia of
the release lever may be locked in the ”release” position flywheel (option F1). Overall dimensions of motors re-
by tightening the lever until lever end becomes engaged main unchanged. The option is available for DC
with a brake housing projection. brake-motors only.

134
(C34) tervene on currents of energizing coils, and must there-
fore be connected to a special control unit (triggering
Main data for flywheel apparatus) to be interfaced with the external connec-
Fly-wheel Fly-wheel
tions.
weight inertia Thus protected, three PTCs connected in series are in-
stalled in the winding, the terminals of which are located
[lbs] [lb • ft2] x 10-5 on the auxiliary terminal-board.
BN 63 M05 0.31 2.7
BN 71 M1 0.51 5.7
BN 80 M2 0.76 11.4
BN 90 Bimetallic thermostates
– 1.14 22.3
BN 90 L
BN 100 M3 1.58 35.4
These types of protective devices house a bimetal disk.
BN 112 – 2.19 62.4 When the rated switch off temperature is reached, the
BN 132 S disk switches the contacts from their initial rest position.
M4 2.81 108.6
BN 132 M As temperature falls, the disk and the contacts automati-
cally return to rest position.
Three bimetallic thermostates connected in series are
usually employed, with normally closed contacts. The ter-
minals are located in an auxiliary terminal-board.

3.9 - SPECIAL EXECUTIONS

Thermal protective devices H1

In addition to the standard protection provided by the Anti-condensation heaters
magneto-thermal device, motors can be supplied with
built-in thermal probes to protect the winding against
overheating caused, by insufficient ventilation or by an Where an application involves high humidity or extreme
intermittent duty. temperature fluctuation, motors may be equipped with
This additional protection should always be specified for an anti-condensate heater.
servoventilated motors (IC416). A single-phase power supply is available in the auxiliary
terminal board inside the main terminal box. Values for
the absorbed power are listed here below:

E3
(C35)
Thermistors H1
1~ 230V ± 10%
These are semi-conductors having rapid resistance vari- P [W]
ation when they are close to the rated switch off temper-
BN 56...BN 80 M0...M2 10
ature.
Variations of the R = f(T) characteristic are specified BN 90...BN 160MR M3 - M4 25
under DIN 44081, IEC 34-11 Standards. BN 160M...BN 180M M5 50
These elements feature several advantages: compact di-
mensions, rapid response time and, being contact-free, BN 180L...BN 200L – 65
absolutely no wear.
Positive temperature coefficient thermistors are normally Warning!
used (also known as PTC “cold conductor resistors”). Always disconnect power supply to the anti-
Unlike bimetallic thermostates, they cannot directly in- condensante heater before operating the motor.

135
 AL AR Ventilation

Motors are cooled through outer air blow (IC 411 ac-
cording to CEI EN 60034-6) and are equipped with a
Backstop device plastic radial fan, which operates in both directions.
Ensure that fan cover is installed at a suitable distance
from the closest wall so to allow air circulation and ser-
For applications where backdriving must be avoided, mo- vicing of motor and brake, if fitted.
tors equipped with an anti run-back device can be used On request, motors can be supplied with independently
(available for the M series only). power-supplied forced ventilation system starting from
While allowing rotation in the direction required, this de- BN 71 or M1 size.
vice operates instantaneously in case of a power failure, Motor is cooled by an axial fan with independent power
preventing the shaft from running back. supply and fitted on the fan cover (IC 416 cooling sys-
The anti run-back device is life lubricated with special tem).
grease for this specific application. This option comes handy for inverter driven motors so
When ordering, customers should indicate the required that constant torque operation is possible even at low
rotation direction, AL or AR. speed or when high starting frequencies are needed.
Never use the anti run-back device to prevent reverse ro- Motors with rear shaft projection (PS option) are ex-
tation caused by faulty electrical connection. cluded.
Table (C36) shows rated and maximum locking torques
for the anti run-back devices.
A diagram of the device can be seen in Table (C37).
Overall dimensions are same as the corresponding (C38)
brake motor.
Power supply

(C36) V a.c.
Hz P [W] I [A]
± 10%
Rated locking Max. locking Release
torque torque speed BN 71 M1 22 0.14

[lb·in] [lb·in] [rpm] BN 80 M2 22 0.14

1~ 230
M1 53 90 750 BN 90 – 40 0.25

M2 140 240 650 BN 100 (*) M3 50 0.25

50 / 60

M3 480 815 520 BN 112 – 50 0.26 / 0.15

M4 970 1815 430 BN 132S M4S 3~ 230 D /

400Y
110 0.38 / 0.22
BN 132M...
(C37) M4L
BN160MR

BN 160...
M5 3~460 60 210 1.25 / 0.72
BN 180M

This variant features two options, designated U1 and

U2, having the same length overall.
Longer side of fan cover (DL) is specified for both mod-
els in the table below. Overall dimension can be reck-
oned from motor size table.

136
(C39) (C41)

Extra length for servoventilated motors [in] AQ DV

D L1 D L2 [in] [in]
add for standard motor add for brakemotor
BN 63 M05 118 24
BN 71 M1 3.66 1.26 BN 71 M1 134 27
BN 80 M2 5.00 2.17 BN 80 M2 134 25

BN 90 – 5.16 1.89 BN 90 – 168 30

BN 100 M3 4.69 1.10 BN 100 M3 168 28

BN 112 – 211 32
BN 112 – 5.12 1.22
BN 132...BN 160MR M4 211 32
BN 132S M4S 6.34 2.01
BN 160M...BN 180M M5 270 36
BN 132M M4L 6.34 2.01
BN 180L...BN 200L – 310 36

U1 (C42)
Fan wiring terminals are housed in a separate terminal
box.
In brake motors of size BN 71...BN 160MR, with U1
model, the release lever cannot be positioned to AA.

U2
Fan terminals are wired in the motor terminal box.
The option does not apply to BN160M...BN200L motors.
(C40)

V a.c. ± 10% Hz P [W] I [A]

(*)
BN 100_U2 M3 3~ 230 D / 400Y 50 / 60 40 0.24 / 0.14

RC
Drip cover
TC
Textile canopy
The drip cover protects the motor from dripping and
avoids the ingress of solid bodies. It is recommended
when motor is installed in a vertical position with the Option TC is a cover variant for textile industry environ-
shaft downwards. ments, where lint may obstruct the fan grid and prevent
Relevant dimensions are indicated in the table (C41). a regular flow of cooling air.
The drip cover is not compatible with variants PS, EN1, This option is not compatible with variants EN1, EN2,
EN2, EN3 and will not fit motors equipped with a BA EN3. Overall dimensions are the same as drip cover
brake. type RC.

137
Feedback units

Motors may be combined with three different types of

encoders to achieve feedback circuits.
Configurations with double-extended shaft (PS) and rain
canopy (RC, TC) are not compatible with the installation
of the encoder.

EN1
Incremental encoder, VIN= 5 V, line-driver output RS
422.

EN2
Incremental encoder, VIN=10-30 V, line-driver output RS
422.

EN3
Incremental encoder, VIN=12-30 V, push-pull output
12-30 V.

(C43)
EN1 EN2 EN3

Interface RS 422 RS 422 push-pull

Power supply voltage [V] 4...6 10...30 12...30

Output voltage [V] 5 5 12...30

No-load operating current [mA] 120 100 100

No. of pulses per revolution 1024

No. of signals 6 (A, B, C + inverted signals)

Max. output frequency [kHz] 300 300 200

Max. speed [rpm] 600 (900 rpm x 10s)

Temperature range [°C] -20...+70

Protection class IP 65

138
 3.10 COMPACT MOTOR RATING CHARTS
2 POLE - 3600 rpm - S1
60 Hz
Pn n Tn h cosj In Is Ts Tk Jm Weight Brake Tb Zo Weight Brake Tb Zo Weight
at 460V In Tn Tn lb×ft2 lbs type 1/h lbs type 1/h lbs

HP kW rpm lb×in % A % % % 1) 2) 1) lb×in 3) 4) 2) lb×in 4) 2)

0.25 0.18 M 05A 2 3380 4.7 60 0.74 0.53 410 300 320 0.0048 0.0062 7.1 FD 02 15 2700 3300 10.8 FA 02 15 3300 10.4

0.33 0.25 M 05B 2 3400 6.1 65 0.75 0.63 490 320 330 0.0055 0.0071 7.9 FD 02 15 2700 3300 11.7 FA 02 15 3300 11.2

0.5 0.37 M 05C 2 3420 9.2 69 0.76 0.89 550 330 350 0.0062 0.0078 10.6 FD 02 30 2500 3000 14.3 FA 02 30 3000 13.9

0.75 0.55 M 1SD 2 3450 13.7 76 0.75 1.23 620 340 390 0.0097 0.0126 12.8 FD 03 44 2200 2700 18.7 FA 03 44 2700 18.1

1 0.75 M 1LA 2 3440 18.3 77 0.75 1.62 620 380 410 0.0119 0.0145 15.2 FD 03 44 1500 2100 21 FA 03 44 2100 21

1.5 1.1 M 2SA 2 3430 27.6 77 0.76 2.40 620 380 390 0.0214 0.0252 19.4 FD 04 88 1200 1600 28 FA 04 88 1600 28

2 1.5 M 2SB 2 3420 36.8 80 0.81 2.89 600 330 350 0.0271 0.0309 23 FD 04 133 1000 1300 32 FA 04 133 1300 32

3 2.2 M 3SA 2 3430 55 81 0.83 4.2 600 240 250 0.0570 0.0665 34 FD 15 230 800 1000 49 FA 15 230 1000 51

5 3.7 M 3LB 2 3490 92 84 0.83 6.7 670 290 320 0.0926 0.102 49 FD 15 354 360 500 62 FA 15 354 500 64

7.5 5.5 M 4SA 2 3490 135 83 0.86 9.8 640 270 300 0.240 0.266 72 FD 06 440 400 101 FA 06 440 400 104

10 7.5 M 4SB 2 3490 181 82 0.88 13.0 620 280 320 0.318 0.344 88 FD 06 440 350 117 FA 06 440 350 143

15 11 M 4LC 2 3510 271 87 0.88 18.3 690 270 300 0.499 132

20 15 M 5SB 2 3510 359 86 0.90 24.2 600 250 270 0.808 154

25 18.5 M 5SC 2 3520 449 88 0.91 29.2 690 280 300 0.998 183

30 22 M 5LA 2 3520 537 88 0.91 35.1 690 280 310 1.164 209

1) Inertia without brake 3) Permissible starts with NB rectifier (AC/DC)

139

2) Inertia with brake 4) Permissible starts with SB rectifier (AC/DC)

140

4 POLE - 1800 rpm - S1

60 Hz
Pn n Tn h cosj In Is Ts Tk Jm Weight Brake Tb Zo Weight Brake Tb Zo Weight
at 460V In Tn Tn lb×ft2 lbs type 1/h lbs type 1/h lbs

HP kW rpm lb×in % A % % % 1) 2) 1) lb×in 3) 4) 2) lb×in 3) 2

0.12 0.09 M 0B 4 1670 4.5 59 0.52 0.37 280 290 290 0.0356 6.4

0.16 0.12 M 05A 4 1690 6.0 60 0.57 0.44 330 240 250 0.0048 0.0062 7.1 FD 02 15 7000 9000 10.8 FA 02 15 9000 10.4

0.25 0.18 M 05B 4 1670 9.4 58 0.60 0.65 320 280 290 0.0055 0.0071 7.9 FD 02 30 7000 9000 11.7 FA 02 30 9000 11.2

0.33 0.25 M 05C 4 1670 12.4 64 0.64 0.77 330 250 260 0.0078 0.0093 10.6 FD 02 30 6000 8000 14.3 FA 02 30 8000 13.9

0.50 0.37 M 1SD 4 1700 18.5 66 0.73 0.96 450 260 280 0.0164 0.0190 12.1 FD 03 44 4800 7500 18.1 FA 03 44 7500 17.4

0.75 0.55 M 1LA 4 1710 27.6 72 0.70 1.37 490 300 310 0.0216 0.0242 15.2 FD 53 66 3400 7000 21 FA 53 66 7000 21

1 0.75 M 2SA 4 1720 36.6 78 0.75 1.61 620 340 350 0.0482 0.0523 20 FD 04 133 3000 6000 29 FA 04 133 6000 29

1.5 1.1 M 2SB 4 1720 55 78 0.76 2.33 630 340 350 0.0594 0.0641 23 FD 04 133 2000 4200 32 FA 04 133 4200 32

2 1.5 M 3SA 4 1720 73 82 0.73 3.15 570 290 330 0.0808 0.0903 34 FD 15 230 1500 3000 49 FA 15 230 3000 51

3 2.2 M 3LA 4 1720 110 81 0.73 4.67 550 270 290 0.0960 0.105 37 FD 15 354 1000 2700 53 FA 15 354 2700 53

5 3.7 M 3LC 4 1730 182 84 0.74 7.5 560 280 310 0.145 0.154 51 FD 55 480 1200 64 FA 55 480 1200 66

7.5 5.5 M 4SA 4 1730 273 84 0.84 9.8 630 290 310 0.506 0.530 93 FD 56 664 850 121 FA 06 664 850 124

10 7.5 M 4LA 4 1740 362 85 0.84 13.2 610 290 300 0.641 0.665 112 FD 06 885 700 141 FA 06 885 700 143

15 11 M 4LC 4 1740 543 88 0.81 19.4 650 310 320 0.855 0.907 143 FD 07 1328 600 179 FA 07 1328 600 183

20 15 M 5SB 4 1750 720 90 0.84 24.9 580 230 270 1.544 1.781 187 FD 08 1770 400 254 FA 08 1770 400 251

25 18.5 M 5LA 4 1760 895 90 0.83 31.1 580 250 310 1.876 2.054 223 FD 08 2210 300 289 FA 08 2210 300 287

1) Inertia without brake 3) Permissible starts with NB rectifier (AC/DC)

2) Inertia with brake 4) Permissible starts with SB rectifier (AC/DC)
 6 POLE - 1200 rpm - S1
60 Hz
Pn n Tn h cosj In Is Ts Tk Jm Weight Brake Tb Zo Weight Brake Tb Zo Weight
at 460V In Tn Tn lb×ft2 lbs type 1/h lbs type 1/h lbs

HP kW rpm lb×in % A % % % 1) 2) 1) lb×in 3) 4) 1) lb×in 4) 2)

0.12 0.09 M 05A 6 1100 6.9 47 0.46 0.52 240 290 290 0.0081 0.0095 9.5 FD 02 30 7000 10000 13.2 FA 02 30 10000 12.8

0.16 0.12 M 05B 6 1100 9.2 49 0.54 0.57 230 240 240 0.0088 0.0102 10.1 FD 02 30 7000 10000 13.9 FA 02 30 10000 13.4

0.25 0.18 M 1SC 6 1100 14.3 61 0.65 0.57 330 260 280 0.0200 0.0226 11.2 FD 03 44 6500 10000 17.2 FA 03 44 10000 16.5

0.33 0.25 M 1SD 6 1100 18.9 64 0.65 0.75 320 260 270 0.0259 0.0290 13.9 FD 03 44 6200 8000 19.8 FA 03 44 8000 19.2

0.50 0.37 M 1LA 6 1100 28.6 66 0.65 1.08 330 260 270 0.0306 0.0330 16.1 FD 53 66 4000 7000 22 FA 03 66 7000 21

0.75 0.55 M 2SA 6 1140 41.4 76 0.66 1.38 490 320 340 0.0594 0.0641 23 FD 04 133 3800 5000 32 FA 04 133 5000 32

1 0.75 M 2SB 6 1140 55 76 0.61 2.03 440 280 300 0.0665 0.0713 25 FD 04 133 2700 5000 34 FA 04 133 5000 34

1.5 1.1 M 3SA 6 1140 83 74 0.68 2.74 440 240 280 0.147 0.157 37 FD 15 230 2300 4500 51 FA 15 230 4500 53

2 1.5 M 3LA 6 1140 111 76 0.66 3.75 450 240 280 0.195 0.204 46 FD 15 354 1500 3000 60 FA 15 354 3000 62

3 2.2 M 3LC 6 1140 166 77 0.68 5.3 510 260 290 0.226 0.235 51 FD 55 480 1500 64 FA 15 480 1500 66

5 3.7 M 4LA 6 1150 274 80 0.79 7.3 610 250 310 0.701 0.724 95 FD 06 885 900 123 FA 06 885 900 126

7.5 5.5 M 4LB 6 1140 414 82 0.75 11.2 540 270 290 0.910 0.964 119 FD 07 1328 800 154 FA 07 1328 800 159

10 7.5 M 5SA 6 1160 543 85 0.82 13.5 580 230 280 1.758 1.936 152 FD 08 1500 550 216 FA 08 1500 550 216

15 11 M 5SB 6 1160 815 84 0.83 19.8 580 250 290 2.304 2.482 196 FD 08 1770 400 262 FA 08 1770 400 260

1) Inertia without brake 3) Permissible starts with NB rectifier (AC/DC)

141

2) Inertia with brake 4) Permissible starts with SB rectifier (AC/DC)

142

3.11 IEC MOTOR RATING CHARTS

2 POLE - 3600 rpm - S1
60 Hz
Pn n Tn h cosj In Is Ts Tk Jm Weight Brake Tb Zo Weight Brake Tb Zo Weight
at 460V In Tn Tn lb×ft2 lbs type 1/h lbs type 1/h lbs

HP kW rpm lb×in % A % % % 1) 2) 1) lb×in 3) 4) 2) lb×in 4) 2)

0.25 0.18 BN 63A 2 3360 4.7 58 0.74 0.55 370 290 300 0.0048 0.0062 7.7 FD 02 15 2700 3300 10.7 FA 02 15 3300 11.0

0.33 0.25 BN 63B 2 3370 6.2 61 0.73 0.69 420 290 300 0.0055 0.0071 8.6 FD 02 15 2700 3300 11.5 FA 02 15 3300 11.9

0.5 0.37 BN 71A 2 3420 9.2 71 0.77 0.86 580 330 380 0.0082 0.0109 11.9 FD 03 30 2400 3200 16.6 FA 03 30 3200 17.2

0.75 0.55 BN 71B 2 3450 13.7 76 0.75 1.23 620 340 390 0.0097 0.0126 13.7 FD 03 44 2200 2700 18.2 FA 03 44 2700 19.0

1 0.75 BN 80A 2 3440 18.3 76 0.76 1.62 590 310 370 0.0185 0.0223 19.0 FD 04 44 1400 1700 26 FA 04 44 1700 27

1.5 1.1 BN 80B 2 3430 27.6 77 0.76 2.40 620 380 390 0.0214 0.0252 21 FD 04 88 1200 1600 27 FA 04 88 1600 29

2 1.5 BN 90SA 2 3480 36.2 79 0.78 3.04 730 360 380 0.0297 0.0335 27 FD 14 133 750 1000 34 FA 14 133 1000 36

3 2.2 BN 90L 2 3490 54 81 0.79 4.4 730 380 390 0.0397 0.0435 31 FD 05 230 750 1000 41 FA 05 230 1000 46

5 3.7 BN 100LB 2 3490 90 84 0.83 6.7 670 290 320 0.0926 0.102 51 FD 15 354 360 500 59 FA 15 354 500 66

7.5 5.5 BN 132SA 2 3490 135 83 0.86 9.8 640 270 300 0.240 0.266 77 FD 06 440 400 98 FA 06 440 400 108

10 7.5 BN 132SB 2 3490 181 82 0.88 13.0 620 280 320 0.318 0.344 93 FD 06 440 350 113 FA 06 440 350 123

15 11 BN 160MR 2 3510 271 87 0.88 18.3 690 270 300 0.499 143

20 15 BN 160MB 2 3510 359 86 0.90 24.2 600 250 270 0.808 185

25 18.5 BN 160L 2 3520 449 88 0.91 29.2 690 280 300 0.998 214

30 22 BN 180M 2 3520 537 88 0.91 35.1 690 280 310 1.164 240

40 30 BN 200L 2 3530 716 89 0.91 46.2 690 260 300 1.829 309

1) Inertia without brake 3) Permissible starts with NB rectifier (AC/DC)

2) Inertia with brake 4) Permissible starts with SB rectifier (AC/DC)
 4 POLE - 1800 rpm - S1
60 Hz
Pn n Tn h cosj In Is Ts Tk Jm Weight Brake Tb Zo Weight Brake Tb Zo Weight
at 460V In Tn Tn lb×ft2 lbs type 1/h lbs type 1/h lbs

HP kW rpm lb×in % A % % % 1) 2) 1) lb×in 3) 4) 2) lb×in 4) 2)

0.08 0.06 BN 56A 4 1670 3.0 53 0.55 0.26 290 310 310 0.0036 6.8

0.12 0.09 BN 56B 4 1670 4.5 59 0.52 0.37 280 290 290 0.0036 6.8

0.16 0.12 BN 63A 4 1650 6.1 55 0.64 0.43 310 240 250 0.0048 0.0062 7.7 FD 02 15 7000 9000 11.5 FA 02 15 9000 11.0

0.25 0.18 BN 63B 4 1670 9.4 58 0.59 0.68 310 280 290 0.0055 0.0071 8.6 FD 02 30 7000 9000 12.3 FA 02 30 9000 11.9

0.33 0.25 BN 71A 4 1700 12.2 64 0.74 0.65 430 260 270 0.0138 0.0164 11.2 FD 03 30 6000 8500 17.2 FA 03 30 8500 16.5

0.50 0.37 BN 71B 4 1700 18.5 66 0.73 0.97 450 260 280 0.0164 0.0190 13.0 FD 03 44 4800 7500 19.0 FA 03 44 7500 18.3

0.75 0.55 BN 80A 4 1710 27.6 73 0.75 1.28 490 300 300 0.0356 0.0394 18.1 FD 04 89 3400 7000 27 FA 04 89 7000 26

1 0.75 BN 80B 4 1720 36.6 78 0.75 1.60 620 340 350 0.0482 0.0523 22 FD 04 133 3000 6000 30 FA 04 133 6000 30

1.5 1.1 BN 90S 4 1720 55 78 0.74 2.43 570 310 340 0.0499 0.0546 27 FD 14 133 3000 7000 36 FA 14 133 7000 36

2 1.5 BN 90LA 4 1720 73 81 0.74 3.12 660 330 360 0.0665 0.0760 30 FD 05 230 2200 4700 43 FA 05 230 4700 45

3 2.2 BN 100LA 4 1720 110 81 0.73 4.8 550 270 290 0.0960 0.105 40 FD 15 354 1000 2700 55 FA 15 354 2700 55

5 3.7 BN 100LC 4 1730 182 84 0.74 7.5 560 280 310 0.145 0.154 55 FD 55 480 1200 66 FA 15 480 1200 64

5.5 4 BN 112M 4 1730 200 85 0.76 8.0 700 310 340 0.233 0.254 66 FD 06S 530 850 88 FA 06S 530 850 93

7.5 5.5 BN 132S 4 1730 273 84 0.84 10.0 630 290 310 0.506 0.530 97 FD 56 664 850 126 FA 06 664 850 128

10 7.5 BN 132MA 4 1740 362 85 0.84 13.1 610 290 300 0.641 0.665 117 FD 06 885 700 146 FA 07 885 700 157

15 11 BN 160MR 4 1740 543 88 0.81 19.4 650 310 320 0.855 0.907 154 FD 07 1328 600 190 FA 07 1328 600 194

20 15 BN 160L 4 1750 720 90 0.84 24.8 580 230 270 1.544 1.722 218 FD 08 1770 400 284 FA 08 1770 400 282

25 18.5 BN 180M 4 1760 895 90 0.83 31.3 580 250 310 1.876 2.054 254 FD 08 2210 300 320 FA 08 2210 300 317

1) Inertia without brake 3) Permissible starts with NB rectifier (AC/DC)

143

2) Inertia with brake 4) Permissible starts with SB rectifier (AC/DC)

144

6 POLE - 1200 rpm - S1

60 Hz
Pn n Tn h cosj In Is Ts Tk Jm Weight Brake Tb Zo Weight Brake Tb Zo Weight
at 460V In Tn Tn lb×ft2 lbs type 1/h lbs type 1/h lbs

HP kW rpm lb×in % A % % % 1) 2) 1) lb×in 3) 4) 2) lb×in 4) 2)

0.12 0.09 BN 63A 6 1100 6.9 47 0.50 0.48 280 290 290 0.0081 0.0095 10.1 FD 02 30 7000 10000 13.9 FA 02 30 10000 13.4

0.16 0.12 BN 63B 6 1100 9.2 50 0.55 0.55 240 240 270 0.0088 0.0102 10.8 FD 02 30 7000 10000 14.6 FA 02 30 10000 14.1

0.25 0.18 BN 71A 6 1100 14.3 61 0.65 0.57 330 260 280 0.0200 0.0226 12.1 FD 03 44 6500 10000 18.1 FA 03 44 10000 17.4

0.33 0.25 BN 71B 6 1100 18.9 64 0.65 0.75 320 260 270 0.0259 0.0285 14.8 FD 03 44 6200 8000 21 FA 03 44 8000 20

0.50 0.37 BN 80A 6 1130 27.9 67 0.65 1.07 390 260 280 0.0499 0.0546 22 FD 04 88 4100 5500 30 FA 04 88 5500 30

0.75 0.55 BN 80B 6 1140 41.4 76 0.66 1.38 490 320 340 0.0594 0.0641 25 FD 04 133 3800 5000 34 FA 04 133 5000 33

1 0.75 BN 90S 6 1140 55.3 73 0.63 2.05 450 290 310 0.0618 0.0665 29 FD 14 133 2700 4000 37 FA 14 133 4000 37

1.5 1.1 BN 90L 6 1140 83 75 0.65 2.83 430 280 290 0.0784 0.0879 33 FD 05 230 2000 3500 46 FA 05 230 3500 49

2 1.5 BN 100LA 6 1140 111 76 0.66 3.75 450 240 280 0.195 0.204 49 FD 15 354 1500 3000 62 FA 15 354 3000 64

3 2.2 BN 112M 6 1150 164 81 0.69 4.9 550 280 290 0.400 0.420 71 FD 06S 530 1250 93 FA 06S 530 1250 97

5.0 3.7 BN 132MA 6 1150 274 80 0.79 7.3 610 250 3.1 0.701 0.724 97 FD 06 885 900 128 FA 07 885 900 139

7.5 5.5 BN 132MB 6 1140 414 82 0.75 11.2 540 270 290 0.910 0.964 123 FD 07 1328 800 159 FA 07 1328 800 163

10 7.5 BN 160M 6 1160 543 85 0.82 13.5 580 230 280 1.758 1.936 183 FD 08 1500 550 247 FA 08 1500 550 249

15 11 BN 160L 6 1160 815 84 0.83 19.8 580 250 290 2.304 2.482 227 FD 08 1770 400 293 FA 08 1770 400 293

1) Inertia without brake 3) Permissible starts with NB rectifier (AC/DC)

2) Inertia with brake 4) Permissible starts with SB rectifier (AC/DC)
 M
3.12 DIMENSIONS

J
LA EA
AF LL

DB
AD

DA

FA
AC
GC

AC AD AF LL J DA EA LA DB GC FA

4.33 3.58 2.91 3.15 3.58 0.35 0.79 0.08 0.40 0.12
M0 M3
110 91 74 80 91 9 20 2 10.2 3
4.76 3.74 2.91 3.15 4.61 0.43 0.91 0.12 0.49 0.16
M 05 M4
121 95 74 80 117 11 23 3 12.5 4
5.43 4.25 2.91 3.15 4.65 0.55 1.18 0.08 0.63 0.20
M 1S M5
138 108 74 80 118 14 30 2 16 5
5.43 4.25 2.91 3.15 5.59 0.55 1.18 0.08 0.63 0.20
M 1L M5
138 108 74 80 142 14 30 2 16 5
6.14 4.69 2.91 3.15 5.98 0.75 1.57 0.12 0.85 0.24
M 2S M6
156 119 74 80 152 19 40 3 21.5 6
7.68 5.59 3.86 3.86 6.95 1.10 2.36 0.12 1.22 0.31
M 3S M10
195 142 98 98 176.5 28 60 3 31 8
7.68 5.59 3.86 3.86 8.21 1.10 2.36 0.12 1.22 0.31
M 3L M10
195 142 98 98 208.5 28 60 3 31 8
10.16 7.60 4.65 4.65 11.67 1.50 3.15 0.12 1.61 0.39
M 4S M12
258 193 118 118 296.5 38 80 3 41 10
10.16 7.60 4.65 4.65 11.67 1.50 3.15 0.12 1.61 0.39
M 4L M12
258 193 118 118 296.5 38 80 3 41 10
10.16 7.60 4.65 4.65 13.05 1.50 3.15 0.12 1.61 0.39
M 4LC M12
258 193 118 118 331.5 38 80 3 41 10
12.20 9.65 7.36 7.36 13.44 1.50 3.15 0.16 1.61 0.39
M 5S M12
310 245 187 187 341.5 38 80 4 41 10
12.20 9.65 7.36 7.36 15.16 1.50 3.15 0.16 1.61 0.39
M 5L M12
310 245 187 187 385 38 80 4 41 10

inch
Dimensions are
mm

145
 M_FD

J
LA EA
AF
LL
AA
AD

DB

DA

FA
AD

AC
AB
Default

GC

ES

AC

AC AD AF LL J R DA EA LA DB GC FA ES

4.76 4.69 3.86 5.24 7.20 3.78 0.43 0.91 0.08 0.49 0.16 0.20
M 05 M4
121 119 98 133 183 96 11 23 2 12.5 4 5
5.43 5.20 3.86 5.24 6.02 4.06 0.55 1.18 0.08 0.63 0.20 0.20
M 1S M5
138 132 98 133 153 103 14 30 2 16 5 5
5.43 5.20 3.86 5.24 6.89 4.06 0.55 1.18 0.08 0.63 0.20 0.20
M 1L M5
138 132 98 133 175 103 14 30 2 16 5 5
6.14 5.63 3.86 5.24 7.24 5.08 0.75 1.57 0.08 0.85 0.24 0.20
M 2S M6
156 143 98 133 184 129 19 40 2 21.5 6 5
7.68 6.10 4.33 6.50 7.95 6.30 1.10 2.36 0.12 1.22 0.31 0.24
M 3S M10
195 155 110 165 202 160 28 60 3 31 8 6
7.68 6.10 4.33 6.50 9.02 6.30 1.10 2.36 0.12 1.22 0.31 0.24
M 3L M10
195 155 110 165 229 160 28 60 3 31 8 6
10.16 7.60 4.65 4.65 11.22 8.90 1.50 3.15 0.12 1.61 0.39 0.24
M 4S M12
258 193 118 118 285 226 38 80 3 41 10 6
10.16 7.60 4.65 4.65 11.22 8.90 1.50 3.15 0.12 1.61 0.39 0.24
M 4L M12
258 193 118 118 285 226 38 80 3 41 10 6
10.16 7.60 4.65 4.65 16.97 8.90 1.50 3.15 0.12 1.61 0.39 0.24
M 4LC M12
258 193 118 118 431 226 38 80 3 41 10 6
12.20 9.65 7.36 7.36 18.94 10.47 1.50 3.15 0.16 1.61 0.39
M 5S M12 —
310 245 187 187 481 266 38 80 4 41 10
12.20 9.65 7.36 7.36 20.67 10.47 1.50 3.15 0.16 1.61 0.39
M 5L M12 —
310 245 187 187 525 266 38 80 4 41 10

inch
Dimensions are
NOTE: The hexagonal socket "ES" is not available with the PS option. mm

146
 M_FA

J
AF LA EA
LL
AA

DB

R
AD

DA

FA
AD

AC
AB
Default

GC

ES

AC

AC AD AF LL J R DA EA LA DB GC FA ES

4.76 3.74 2.91 3.15 7.20 4.57 0.43 0.91 0.08 0.49 0.16 0.20
M 05 M4
121 95 74 80 183 116 11 23 2 12.5 4 5
5.43 4.25 2.91 3.15 6.02 4.88 0.55 1.18 0.08 0.63 0.20 0.20
M 1S M5
138 108 74 80 153 124 14 30 2 16 5 5
5.43 4.25 2.91 3.15 6.89 4.88 0.55 1.18 0.08 0.63 0.20 0.20
M 1L M5
138 108 74 80 175 124 14 30 2 16 5 5
6.14 4.69 2.91 3.15 7.24 5.28 0.75 1.57 0.08 0.85 0.24 0.20
M 2S M6
156 119 74 80 184 134 19 40 2 21.5 6 5
7.68 5.59 3.86 3.86 7.95 6.30 1.10 2.36 0.12 1.22 0.31 0.24
M 3S M10
195 142 98 98 202 160 28 60 3 31 8 6
7.68 5.59 3.86 3.86 9.02 6.30 1.10 2.36 0.12 1.22 0.31 0.24
M 3L M10
195 142 98 98 229 160 28 60 3 31 8 6
10.16 7.60 4.65 4.65 10.16 8.54 1.50 3.15 0.12 1.61 0.39 0.24
M 4S M14
258 193 118 118 258 217 38 80 3 41 10 6
10.16 7.60 4.65 4.65 11.22 8.54 1.50 3.15 0.12 1.61 0.39 0.24
M 4L M14
258 193 118 118 285 217 38 80 3 41 10 6
10.16 7.60 4.65 4.65 16.97 8.54 1.50 3.15 0.12 1.61 0.39 0.24
M 4LC M14
258 193 118 118 431 217 38 80 3 41 10 6
12.20 9.21 6.73 7.36 18.94 9.72 1.50 3.15 0.16 1.61 0.39
M 5S M12 —
310 234 171 187 481 247 38 80 4 41 10
12.20 9.21 6.73 7.36 20.67 9.72 1.50 3.15 0.16 1.61 0.39
M 5L M12 —
310 234 171 187 525 247 38 80 4 41 10

inch
Dimensions are
NOTE: The hexagonal socket "ES" is not available with the PS option. mm

147
 IM B14 BN
LC
L
E LB EA
V LL
AF
T

DB DB

AD
°
45
DA

FA
F

AC
N
D
P

GA GC

S
M

Shaft Flange Motor

D E GA F
DB M N P S T AC L LB LC AD AF LL V
DA EA GC FA
0.35 0.79 0.40 0.12 2.56 1.97 3.15 0.10 4.33 7.28 6.50 8.15 3.58 2.91 3.15 1.34
BN 56 M3 M5
9 20 10.2 3 65 50 80 2.5 110 185 165 207 91 74 80 34
0.43 0.91 0.49 0.16 2.95 2.36 3.54 0.10 4.76 8.15 7.24 9.13 3.74 2.91 3.15 1.02
BN 63 M4 M5
11 23 12.5 4 75 60 90 2.5 121 207 184 232 95 74 80 26
0.55 1.18 0.63 0.20 3.35 2.76 4.13 0.10 5.43 9.80 8.62 11.06 4.25 2.91 3.15 1.46
BN 71 M5 M6
14 30 16 5 85 70 105 2.5 138 249 219 281 108 74 80 37
0.75 1.57 0.85 0.24 3.94 3.15 4.72 0.12 6.14 10.79 9.21 12.40 4.69 2.91 3.15 1.50
BN 80 M6 M6
19 40 21.5 6 100 80 120 3 156 274 234 315 119 74 80 38
0.94 1.97 1.06 0.31 4.53 3.74 5.51 0.12 6.93 12.83 10.87 14.88 5.24 3.86 3.86 1.73
BN 90 S M8 M8
24 50 27 8 115 95 140 3 176 326 276 378 133 98 98 44
0.94 1.97 1.06 0.31 4.53 3.74 5.51 0.12 6.93 12.83 10.87 14.88 5.24 3.86 3.86 1.73
BN 90 L M8 M8
24 50 27 8 115 95 140 3 176 326 276 378 133 98 98 44
1.10 2.36 1.22 0.31 5.12 4.33 6.30 0.14 7.68 14.41 12.05 16.89 5.59 3.86 3.86 1.97
BN 100 M10 M8
28 60 31 8 130 110 160 3.5 195 366 306 429 142 98 98 50
1.10 2.36 1.22 0.31 5.12 4.33 6.30 0.14 8.62 15.16 12.80 17.64 6.18 3.86 3.86 2.05
BN 112 M10 M8
28 60 31 8 130 110 160 3.5 219 385 325 448 157 98 98 52
1.50 3.15 1.61 0.39 6.50 5.12 7.87 0.16 10.16 17.91 14.76 21.18 7.60 4.65 4.65 2.28
BN 132 S M12 M10
38 80 41 10 165 130 200 4 258 455 375 538 193 118 118 58
1.50 3.15 1.61 0.39 6.50 5.12 7.87 0.16 10.16 19.41 16.26 22.68 7.60 4.65 4.65 2.28
BN 132 M M12 M10
38 80 41 10 165 130 200 4 258 493 413 576 193 118 118 58

inch
Dimensions are
1) These values refer to the rear shaft end. mm

148
 BN IM B5

Shaft Flange Motor

D E GA F
DB M N P S T LA AC L LB LC AD AF LL V
DA EA GC FA
0.43 0.91 0.49 0.16 4.53 3.74 5.51 0.37 0.12 0.39 4.76 8.15 7.24 9.13 3.74 2.91 3.15 1.02
BN 63 M4
11 23 12.5 4 115 95 140 9.5 3 10 121 207 184 232 95 74 80 26
0.55 1.18 0.63 0.20 5.12 4.33 6.30 0.37 0.12 0.39 5.43 9.80 8.62 11.06 4.25 2.91 3.15 1.46
BN 71 M5
14 30 16 5 130 110 160 9.5 3 10 138 249 219 281 108 74 80 37
0.75 1.57 0.85 0.24 6.50 5.12 7.87 0.45 0.14 0.45 6.14 10.79 9.21 12.40 4.69 2.91 3.15 1.50
BN 80 M6
19 40 21.5 6 165 130 200 11.5 3.5 11.5 156 274 234 315 119 74 80 38
BN 90 S 0.94 1.97 1.06 0.31 6.50 5.12 7.87 0.45 0.14 0.45 6.93 12.83 10.87 14.88 5.24 3.86 3.86 1.73
M8
BN 90 L 24 50 27 8 165 130 200 11.5 3.5 11.5 176 326 276 378 133 98 98 44
1.10 2.36 1.22 0.31 8.46 7.09 9.84 0.55 0.16 0.55 7.68 14.45 12.09 16.89 5.59 3.86 3.86 1.97
BN 100 M10
28 60 31 8 215 180 250 14 4 14 195 367 307 429 142 98 98 50
1.10 2.36 1.22 0.31 8.46 7.09 9.84 0.55 0.16 0.59 8.62 15.16 12.80 17.64 6.18 3.86 3.86 2.05
BN 112 M10
28 60 31 8 215 180 250 14 4 15 219 385 325 448 157 98 98 52
1.49 3.14 1.61 0.39 10.43 9.05 11.81 0.55 0.15 0.62 10.15 17.91 14.76 21.18 7.59 4.64 4.64 2.28
BN 132 S M12
38 80 41 10 265 230 300 14 4 16 258 455 375 538 193 118 118 58
1.49 3.14 1.61 0.39 10.43 9.05 11.81 0.55 0.15 0.62 10.15 19.40 16.25 22.67 7.59 4.64 4.64 2.28
BN 132 M M12
38 80 41 10 265 230 300 14 4 16 258 493 413 576 193 118 118 58
1.65 4.33 1.77 0.47
M16
42 110 45 12 11.81 9.84 13.77 0.72 0.19 0.59 10.15 22.12 17.79 25.39 7.59 4.64 4.64 8.58
BN 160 MR
1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 258 562 452 645 193 118 118 218
M12 (1)
38 (1) 80 (1) 41 (1) 10 (1)
1.65 4.33 1.77 0.47
M16
BN 160 M 42 110 45 12 11.81 9.84 13.77 0.72 0.19 0.59 1.22 23.46 19.13 26.77 9.64 7.36 7.36 2.00
BN 160 L 1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 310 596 486 680 245 187 187 51
M12 (1)
38(1) 80 (1) 41 (1) 10 (1)
1.88 4.33 2.02 0.55
M16
48 110 51.5 14 11.81 9.84 13.77 0.72 0.19 0.59 1.22 25.19 20.86 28.50 9.64 7.36 7.36 2.00
BN 180 M
1.49 4.33 1.61 0.39 300 250 350 18.5 5 15 310 640 530 724 245 187 187 51
M12 (1)
38 (1) 110 (1) 41 (1) 10 (1)
1.88 4.33 2.02 0.55
M16
48 110 51.5 14 11.81 9.84 13.77 0.72 0.19 0.70 13.70 27.87 23.54 32.40 10.27 7.36 7.36 2.04
BN 180 L
1.65 4.33 1.77 0.47 300 250 350 18.5 5 18 348 708 598 823 261 187 187 52
M16 (1)
42 (1) 110 (1) 45 (1) 12 (1)
2.16 4.33 2.32 0.62
M20
55 110 59 16 13.77 11.81 15.74 0.72 0.19 0.70 13.70 28.42 24.09 32.95 10.27 7.36 7.36 2.59
BN 200 L
1.65 4.33 1.77 0.47 350 300 400 18.5 5 18 348 722 612 837 261 187 187 66
M16 (1)
42 (1) 110 (1) 45 (1) 12 (1)

inch
Dimensions are
1) These values refer to the rear shaft end. mm

149
 IM B14 BN_FD

LC
L AF
E LB EA
V LL AA
T

AD
DB DB

"
45
DA

FA
F

AB AD

AC
N
D
P

standard

GC
GA

ES

S AC
M

Shaft Flange Motor

D E GA F
DB M N P S T AC L LB LC AD AF LL V R ES
DA EA GC FA
0.43 0.91 0.49 0.16 2.95 2.36 3.54 0.10 4.76 10.71 9.80 11.69 4.69 3.86 5.24 0.55 3.78 0.20
BN 63 M4 M5
11 23 12.5 4 75 60 90 2.5 121 272 249 297 119 98 133 14 96 5
0.55 1.18 0.63 0.20 3.35 2.76 4.13 0.10 5.43 12.20 11.02 13.46 5.20 3.86 5.24 1.18 4.06 0.20
BN 71 M5 M6
14 30 16 5 85 70 105 2.5 138 310 280 342 132 98 133 30 103 5
0.75 1.57 0.85 0.24 3.94 3.15 4.72 0.12 6.14 13.62 12.05 15.28 5.63 3.86 5.24 1.61 5.08 0.20
BN 80 M6 M6
19 40 21.5 6 100 80 120 3 156 346 306 388 143 98 133 41 129 5
0.94 1.97 1.06 0.31 4.53 3.74 5.51 0.12 6.93 16.10 14.13 18.15 5.75 4.33 6.50 1.54 5.08 0.24
BN 90 S M8 M8
24 50 27 8 115 95 140 3 176 409 359 461 146 110 165 39 129 6
0.94 1.97 1.06 0.31 4.53 3.74 5.51 0.12 6.93 16.10 14.13 18.15 5.75 4.33 6.50 1.54 6.30 0.24
BN 90 L M8 M8
24 50 27 8 115 95 140 3 176 409 359 461 146 110 165 39 160 6
1.10 2.36 1.22 0.31 5.12 4.33 6.30 0.14 7.68 18.03 15.67 20.51 6.10 4.33 6.50 2.44 6.30 0.24
BN 100 M10 M8
28 60 31 8 130 110 160 3.5 195 458 398 521 155 110 165 62 160 6
1.10 2.36 1.22 0.31 5.12 4.33 6.30 0.14 8.62 19.06 16.69 21.54 6.69 4.33 6.50 2.87 7.83 0.24
BN 112 M10 M8
28 60 31 8 130 110 160 3.5 219 484 424 547 170 110 165 73 199 6
1.50 3.15 1.61 0.39 6.50 5.12 7.87 0.16 10.16 22.24 19.09 25.51 7.60 4.65 4.65 5.59 8.03 0.24
BN 132 S M12 M10
38 80 41 10 165 130 200 4 258 565 485 648 193 118 118 142 204 (2) 6
1.50 3.15 1.61 0.39 6.50 5.12 7.87 0.16 10.16 23.74 20.59 27.01 7.60 4.65 4.65 7.09 8.03 0.24
BN 132 M M12 M10
38 80 41 10 165 130 200 4 258 603 523 686 193 118 118 180 204 (2) 6

1) These values refer to the rear shaft end. ES hexagon is not supplied with PS option inch
Dimensions are
2) For FD07 brake value R=226 mm

150
 BN_FD IM B5

Shaft Flange Motor

D E GA F
DB M N P S T LA AC L LB LC AD AF LL V R ES
DA EA GC FA
0.43 0.91 0.49 0.16 4.53 3.74 5.51 0.37 0.12 0.39 4.76 10.71 9.80 11.69 4.69 3.86 5.24 0.55 3.78 0.20
BN 63 M4
11 23 12.5 4 115 95 140 9.5 3 10 121 272 249 297 119 98 133 14 96 5
0.55 1.18 0.63 0.20 5.12 4.33 6.30 0.37 0.14 0.39 5.43 12.20 11.02 13.46 5.20 3.86 5.24 1.18 4.06 0.20
BN 71 M5
14 30 16 5 130 110 160 9.5 3.5 10 138 310 280 342 132 98 133 30 103 5
0.75 1.57 0.85 0.24 6.50 5.12 7.87 0.45 0.14 0.45 6.14 13.62 12.05 15.28 5.63 3.86 5.24 1.61 5.08 0.20
BN 80 M6
19 40 21.5 6 165 130 200 11.5 3.5 11.5 156 346 306 388 143 98 133 41 129 5
0.94 1.97 1.06 0.31 6.50 5.12 7.87 0.45 0.14 0.45 6.93 16.10 14.13 18.15 5.75 4.33 6.50 1.54 5.08 0.24
BN 90 S M8
24 50 27 8 165 130 200 11.5 3.5 11.5 176 409 359 461 146 110 165 39 129 6
0.94 1.97 1.06 0.31 6.50 5.12 7.87 0.45 0.14 0.45 6.93 16.10 14.13 18.15 5.75 4.33 6.50 1.54 6.30 0.24
BN 90 L M8
24 50 27 8 165 130 200 11.5 3.5 11.5 176 409 359 461 146 110 165 39 160 6
1.10 2.36 1.22 0.31 8.46 7.09 9.84 0.55 0.16 0.55 7.68 18.03 15.67 20.51 6.10 4.33 6.50 2.44 6.30 0.24
BN 100 M10
28 60 31 8 215 180 250 14 4 14 195 458 398 521 155 110 165 62 160 6
1.10 2.36 1.22 0.31 8.46 7.09 9.84 0.55 0.16 0.59 8.62 19.06 16.69 21.54 6.69 4.33 6.50 2.87 7.83 0.24
BN 112 M10
28 60 31 8 215 180 250 14 4 15 219 484 424 547 170 110 165 73 199 6
1.49 3.14 1.61 0.39 10.43 9.05 11.81 0.55 0.15 0.62 10.15 22.24 19.09 25.51 7.59 4.64 4.64 5.59 8.03 0.23
BN 132 S M12
38 80 41 10 265 230 300 14 4 16 258 565 485 648 193 118 118 142 204 (2) 6
1.49 3.14 1.61 0.39 10.43 9.05 11.81 0.55 0.15 0.62 10.15 23.74 20.59 27.00 7.59 4.64 4.64 7.08 8.03 0.23
BN 132 M M12
38 80 41 10 265 230 300 14 4 16 258 603 523 686 193 118 118 180 204 (1) 6
1.65 4.33 1.77 0.47
M16
42 110 45 12 11.81 9.84 13.77 0.72 0.19 0.59 10.15 26.45 22.12 29.72 7.59 4.64 4.64 8.58 8.89 0.23
BN 160 MR
1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 258 672 562 755 193 118 118 218 226 6
M12 (1)
38 (1) 80 (1) 41 (1) 10 (1)
1.65 4.33 1.77 0.47
M16
BN 160 M 42 110 45 12 11.81 9.84 13.77 0.72 0.19 0.59 1.22 28.97 24.64 32.28 9.64 7.36 7.36 2.00 8.89
BN 160 L 1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 310 736 626 820 245 187 187 51 226
M12 (1)
38 (1) 80 (1) 41 (1) 10 (1)
1.88 4.33 2.02 0.55
M16
48 110 51.5 14 11.81 9.84 13.77 0.72 0.19 0.59 1.22 30.70 26.37 34.01 9.64 7.36 7.36 2.00 8.89
BN 180 M
1.49 4.33 1.61 0.39 300 250 350 18.5 5 15 310 780 670 864 245 187 187 51 226
M12 (1)
38 (1) 110 (1) 41 (1) 10 (1)
1.88 4.33 2.02 0.55
M16
48 110 51.5 14 11.81 9.84 13.77 0.72 0.19 0.70 13.70 34.09 29.76 38.62 10.27 7.36 7.36 2.04 12.00
BN 180 L
1.65 4.33 1.77 0.47 300 250 350 18.5 5 18 348 866 756 981 261 187 187 52 305
M16 (1)
42 (1) 110 (1) 45 (1) 12 (1)
2.16 4.33 2.32 0.62
M20
55 110 59 16 13.77 11.81 15.74 0.72 0.19 0.70 13.70 34.56 30.23 39.09 10.27 7.36 7.36 2.51 12.00
BN 200 L
1.65 4.33 1.77 0.47 350 300 400 18.5 5 18 348 878 768 993 261 187 187 64 305
M16 (1)
42 (1) 110 (1) 45 (1) 12 (1)

1) These values refer to the rear shaft end. ES hexagon is not supplied with PS option inch
Dimensions are
2) For FD07 brake value R=226 mm

151
 IM B14 BN_FA

LC
L AF
E LB EA
V LL
AA
T

DB DB

AD
°
45
DA

FA
F

AC
AB AD
N
D
P

standard

GC
GA

ES

S AC
M

Shaft Flange Motor

D E GA F
DB M N P S T AC L LB LC AD AF LL V R ES
DA EA GC FA
0.43 0.91 0.49 0.16 2.95 2.36 3.54 0.10 4.76 10.71 9.80 4.69 3.74 2.91 3.15 1.02 4.57 0.20
BN 63 M4 M5
11 23 12.5 4 75 60 90 2.5 121 272 249 119 95 74 80 26 116 5
0.55 1.18 0.63 0.20 3.35 2.76 4.13 0.10 5.43 12.20 11.02 13.46 4.25 2.91 3.15 2.68 4.88 0.20
BN 71 M5 M6
14 30 16 5 85 70 105 2.5 138 310 280 342 108 74 80 68 124 5
0.75 1.57 0.85 0.24 3.94 3.15 4.72 0.12 6.14 13.62 12.05 15.28 4.69 2.91 3.15 3.27 5.28 0.20
BN 80 M6 M6
19 40 21.5 6 100 80 120 3 156 346 306 388 119 74 80 83 134 5
0.94 1.97 1.06 0.31 4.53 3.74 5.51 0.12 6.93 16.10 14.13 18.15 5.24 3.86 3.86 3.74 5.28 0.24
BN 90 S M8 M8
24 50 27 8 115 95 140 3 176 409 359 461 133 98 98 95 134 6
0.94 1.97 1.06 0.31 4.53 3.74 5.51 0.12 6.93 16.10 14.13 18.15 5.24 3.86 3.86 3.74 6.30 0.24
BN 90 L M8 M8
24 50 27 8 115 95 140 3 176 409 359 461 133 98 98 95 160 6
1.10 2.36 1.22 0.31 5.12 4.33 6.30 0.14 7.68 18.03 15.67 20.51 5.59 3.86 3.86 4.69 6.30 0.24
BN 100 M10 M8
28 60 31 8 130 110 160 3.5 195 458 398 521 142 98 98 119 160 6
1.10 2.36 1.22 0.31 5.12 4.33 6.30 0.14 8.62 19.06 16.69 21.54 6.18 3.86 3.86 5.04 7.80 0.24
BN 112 M10 M8
28 60 31 8 130 110 160 3.5 219 484 424 547 157 98 98 128 198 6
1.50 3.15 1.61 0.39 6.50 5.12 7.87 0.16 10.16 22.24 19.09 25.51 7.60 4.65 4.65 5.59 7.87 0.24
BN 132 S M12 M10
38 80 41 10 165 130 200 4 258 565 485 648 193 118 118 142 200 (2) 6
1.50 3.15 1.61 0.39 6.50 5.12 7.87 0.16 10.16 23.74 20.59 27.01 7.60 4.65 4.65 7.09 7.87 0.24
BN 132 M M12 M10
38 80 41 10 165 130 200 4 258 603 523 686 193 118 118 180 200 (2) 6

1) These values refer to the rear shaft end. ES hexagon is not supplied with PS option.
2) For FD07 brake value R=226 For motors type BN..FA, the terminal box sizes AD, AF, LL, inch
Dimensions are
V are the same as for BN..FD. mm

152
 BN_FA IM B5

Shaft Flange Motor

D E GA F
DB M N P S T LA AC L LB LC AD AF LL V R ES
DA EA GC FA
0.43 0.91 0.49 0.16 4.53 3.74 5.51 0.37 0.12 0.39 4.76 10.71 9.80 11.69 3.74 2.91 3.15 1.02 4.57 0.20
BN 63 M4
11 23 12.5 4 115 95 140 9.5 3 10 121 272 249 297 95 74 80 26 116 5
0.55 1.18 0.63 0.20 5.12 4.33 6.30 0.37 0.14 0.39 5.43 12.20 11.02 13.46 4.25 2.91 3.15 2.68 4.88 0.20
BN 71 M5
14 30 16 5 130 110 160 9.5 3.5 10 138 310 280 342 108 74 80 68 124 5
0.75 1.57 0.85 0.24 6.50 5.12 7.87 0.45 0.14 0.45 6.14 13.62 12.05 15.28 4.69 2.91 3.15 3.27 5.28 0.20
BN 80 M6
19 40 21.5 6 165 130 200 11.5 3.5 11.5 156 346 306 388 119 74 80 83 134 5
0.94 1.97 1.06 0.31 6.50 5.12 7.87 0.45 0.14 0.45 6.93 16.10 14.13 18.15 5.24 3.86 3.86 3.74 5.28 0.24
BN 90 S M8
24 50 27 8 165 130 200 11.5 3.5 11.5 176 409 359 461 133 98 98 95 134 6
0.94 1.97 1.06 0.31 6.50 5.12 7.87 0.45 0.14 0.45 6.93 16.10 14.13 18.15 5.24 3.86 3.86 3.74 6.30 0.24
BN 90 L M8
24 50 27 8 165 130 200 11.5 3.5 11.5 176 409 359 461 133 98 98 95 160 6
1.10 2.36 1.22 0.31 8.46 7.09 9.84 0.55 0.16 0.55 7.68 18.03 15.67 20.51 5.59 3.86 3.86 4.69 6.30 0.24
BN 100 M10
28 60 31 8 215 180 250 14 4 14 195 458 398 521 142 98 98 119 160 6
1.10 2.36 1.22 0.31 8.46 7.09 9.84 0.55 0.16 0.59 8.62 19.06 16.69 21.54 6.18 3.86 3.86 5.04 7.80 0.24
BN 112 M10
28 60 31 8 215 180 250 14 4 15 219 484 424 547 157 98 98 128 198 6
1.49 3.14 1.61 0.39 10.43 9.05 11.81 0.55 0.15 0.62 10.15 22.24 19.09 25.51 7.59 4.64 4.64 5.59 7.87 0.23
BN 132 S M12
38 80 41 10 265 230 300 14 4 16 258 565 485 648 193 118 118 142 200 (2) 6
1.49 3.14 1.61 0.39 10.43 9.05 11.81 0.55 0.15 0.62 10.15 23.74 20.59 27.00 7.59 4.64 4.64 7.08 7.87 0.23
BN 132 M M12
38 80 41 10 265 230 300 14 4 16 258 603 523 686 193 118 118 180 200 (1) 6
1.65 4.33 1.77 0.47
M16
42 110 45 12 11.81 9.84 13.77 0.72 0.19 0.59 10.15 26.45 22.12 29.72 7.59 4.64 4.64 8.58 8.54 0.23
BN 160 MR
1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 258 672 562 755 193 118 118 218 217 6
M12 (1)
38 (1) 80 (1) 41 (1) 10 (1)
1.65 4.33 1.77 0.47
M16
BN 160 M 42 110 45 12 11.81 9.84 13.77 0.72 0.19 0.59 1.22 28.97 24.64 32.28 9.64 7.36 7.36 2.00 9.72
BN 160 L 1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 310 736 626 820 245 187 187 51 247
M12 (1)
38 (1) 80 (1) 41 (1) 10 (1)
1.88 4.33 2.02 0.55
M16
48 110 51.5 14 11.81 9.84 13.77 0.72 0.19 0.59 1.22 30.70 26.37 34.01 9.64 7.36 7.36 2.00 9.72
BN 180 M
1.49 3.14 1.61 0.39 300 250 350 18.5 5 15 310 780 670 864 245 187 187 51 247
M12 (1)
38 (1) 80 (1) 41 (1) 10 (1)

1) These values refer to the rear shaft end. ES hexagon is not supplied with PS option.
2) For FD07 brake value R=226 For motors type BN..FA, the terminal box sizes AD, AF, LL, inch
Dimensions are
V are the same as for BN..FD. mm

153
 R3

This publication supersedes any previous edition and revision. We reserve the right to implement modifications without notice.
This catalogue cannot be reproduced, even partially, without prior consent.

154
COD. 1822
 A

High efficiency (η 0.95÷0.97) thanks

to the high performance offered
by the patented hypoid bevel gear pair
at output

Low-noise gearing

High load capacity

A
MANAGEMENT SERVICE

ISO 9001