Scribd
Upload
602 views

Instruction of Plasma Cutting Machine Upgrade

The document provides instructions for upgrading a plasma cutting machine. It outlines a four step process: 1. Install a new text library by copying files to a USB drive and restarting the machine. 2. Upgrade the system by changing a chip, copying upgrade files to the USB drive, and restarting when prompted. 3. Install a new system by copying additional files to the USB drive if the previous step was completed. 4. Restart the machine after shutdown to complete the upgrade process. Attention is given to modifying parameters and settings after startup.

Uploaded by

uripss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
602 views

Instruction of Plasma Cutting Machine Upgrade

The document provides instructions for upgrading a plasma cutting machine. It outlines a four step process: 1. Install a new text library by copying files to a USB drive and restarting the machine. 2. Upgrade the system by changing a chip, copying upgrade files to the USB drive, and restarting when prompted. 3. Install a new system by copying additional files to the USB drive if the previous step was completed. 4. Restart the machine after shutdown to complete the upgrade process. Attention is given to modifying parameters and settings after startup.

Uploaded by

uripss
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

Instruction of Plasma Cutting Machine Upgrade

Click:1502 Date:2013-3-4 21:28:20

Installation of New Plasma Cutting Machine upgrade


Installation of the system upgrade, requires two steps upgrading. The first step: install a new text libra
ry, if the new text library has been installed, this step can be omitted. Step two: Install the Russian sy
stem.
The specific steps are as follows
Step One: Download the original file
1. STARTCNC1.EXE
2. STARTCNC2.EXE

Step two: open the back cover of the system, find a white 3p spin on the board.
Change it as picture shows.

1. copy files
Will STARTCNC1.EXE, renamed STARTCNC.EXE, stored in a U disk.
2. Power
Different systems, see a different approach.
3. Upgrade
When the prompt appears on the screen to upgrade the system's USB port plug in the U disk, pr
ess 【F1】 key, wait for the update. When the "Upgrade Success!"prompt, the shutdown.
4. install a new text library
5 seconds before turning off the screen on, pause for about 10 seconds (this time without any dis
play on the screen, the system is installed a new text library) manually after shut down.

The third step: install the new system


If the second step has been completed, or has a new system, the implementation of this step
.

1. copy files
Will STARTCNC2.EXE, renamed STARTCNC.EXE, stored in a U disk.
2. Power
Different systems, see a different approach.
3. Upgrade
When the prompt appears on the screen to upgrade the system's USB port plug in the U disk, pr
ess 【F1】 key,

Waiting to upgrade. When the "Upgrade Success!"prompt, the shutdown.

Step Four: the end of upgrade


Shutdown, and then restart the upgrade completed.

Some attention after turned on:


1. modify the parameters [set] - [System] - "Reset direction " are set to 0
2. modify the parameters [set] - [Control] -
Took over the control box outside the choice 0
G41/G42 detection effectively 0
Select the soft limit of 1 / No 00
Effective 1 External limit
Collision detection and effective gun 0
Select 0 after a pause Taiqiang
3 changes back / forward speed
[Settings] - [Speed] - Back / forward speed of 2000

4 to determine the mechanical machine zero is


The torch on the processing of a starting point, [Manual] --- [secondary] --- [Reset]

5 when the program is very large (do not display all graphic) , It can use the two methods as
follows:
a) In the [parameter] is set to [control], the width of the plate X, and Y height of the actual value is
written;
b) into the editor (go to exit), restart the run, the system will automatically adjust the zoom.

You might also like