SDRSharp Users Guide https://www.rtl-sdr.

com/sdrsharp-users-guide/

rtl-sdr.com
RTL-SDR (RTL2832U) and software defined radio news and projects. Also featuring Airspy, HackRF, FCD, SDRplay and more.

Home
About RTL-SDR
Quick Start Guide
Featured Articles
Tutorials
Air and Marine
ADS-B Aircraft Radar
ACARS Decoding
AIS Ship Tracking
Decoding Weather Balloons
Satellite
NOAA Weather Satellites
Meteor-M Weather Satellites
Inmarsat STD-C NCS EGC Decoding
Decoding and Plotting GPS
Decoding HRPT Weather Satellite Images
Terrestrial
P25 P1 Digital Voice Decoding
P25 P2 Decoding with OP25
Trunked Radio Following
POCSAG Pager Decoding
TETRA Voice Decoding
Analyzing GSM Signals
DRM Radio Decoding
Decoding 433 MHz ISM Band Weather Stations
Single Board Computer
QRP (FT8, JT9, WSPR etc) Monitoring Station
Performing Replay Attacks with RTL-SDR and RpiTX
Other
Radio Astronomy
Measuring Filter Characteristics & VSWR
SpyServer Tutorial
Using the V3 Bias Tee on PiAware
Properly Positioning a Preamp/LNA
Product Reviews
SDRs
Airspy HF+ Review
Airspy vs. SDRplay vs. HackRF
SDRplay RSP1A
SDRplay RSP2
FlightAware ADS-B RTL-SDR
Outernet Dreamcatcher
LimeSDR Review
LimeSDR Mini
ThumbNet N3
Airspy Mini
PlutoSDR Unboxing
PlutoSDR Tests
KiwiSDR Review
FlightAware Prostick vs Prostick Plus
HackRF PortaPack Review
SpyVerter Upconverter
9A4QV Folded Monopole ADS-B Antenna
FlightAware ADS-B Antenna and Filter
Outernet LNA and Patch Antenna
moRFeus Review
Interesting
TEMPEST with SDR
Listening to HD Radio
Receiving Dead Satellites
Listening to SCA Broadcasts
Live ADS-B Aircraft Cockpit
Transmitting with a Raspberry Pi
Quick Start Guides
RTL-SDR QSG
V3 Features Users Guide
SDRSharp Users Guide
PlutoSDR QSG
Direct Sampling Mod
Roundup of Software Defined Radios
Software
RTL-SDR Supported Software
List of SDRSharp Plugins
Experimental Drivers
Experimental HF Driver
Manual gain controls and decimation driver
ExtIO with Decimation & Tuner Bandwidth Controls
Keenerds Driver
L-Band Heat Issue Driver
Signal ID Wiki
Forum
RTL-SDR Store
Guide Book
Contact

May 8, 2018

SDRSharp Users Guide

This is an excerpt from our book on RTL-SDR which we've decided to post given that many new users struggle to understand all the settings in SDR#.

SDR# is currently the most popular SDR program used with the RTL-SDR. It's easy to set up and use. To install SDR#, go through our Quickstart Guide. Below we explain some of the settings and displays in SDR#.

Upon opening SDR# you'll be greeted with the screen shown below. Here we have highlighted the main parts of SDR#

1 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

After opening SDR# for the first time, we suggest that you immediately remember to perform the following steps (if you don’t know what some of these steps are, continue reading further below for more information):

1. Increase the RF gain from zero to a higher value in the configure menu.
2. Reduce the range slider on the right of the SDR# window to about -70 (for RTL-SDR dongles).
3. Enable the “Correct IQ” setting to remove the center spike if using an R820T/R820T2, or enable “Offset Tuning” in the configure menu if using an E4000/FC0012/13.
4. Turn off the “Snap to grid” setting, or adjust the PPM offset accordingly.
5. Set the 'Mode' to the correct setting for the signal that you are listing to.

Main Settings and Windows

Note that there is a distinction in SDR# between settings that affect the software side, and settings that affect the hardware side. All hardware side settings can be found in the Configure Menu window which can be accessed with the cog
icon . In here are settings to control things like the RF gain and sample rate / bandwidth of the RTL-SDR. To optimize reception, you need to adjust settings in this window.

Most of the settings found in the main windows of SDR# affect the software digital signal processing (DSP) side of things. To optimize processing of the signal you need to adjust these DSP settings.

Control/View Explanation
Play Button /
This button is used to start and stop the SDR.
Stop Button
This is a drop down menu which is used to select the SDR input device being used. If you are using an RTL-SDR, select RTL-SDR/USB. Be sure to NOT select RTL-SDR/TCP unless you are using a remote server with
Source
rtl_tcp.
Configure
Clicking this button opens up the configure menu. In here you can change settings like the sample rate (bandwidth) and RF gain. See further down for more information about these settings.
Menu

Use the mouse to set the desired frequency you wish to listen to here. You can either click on the tops and bottoms of each individual number to increase or decrease the value, or simply hover over the number you want
to change and use the mouse wheel to alter the value.

Frequency
Input
The frequency input is divided into 4 sections with each section containing 3 values (e.g. 000.000.000.000). The first section represents GHz frequency values, the second MHz, the third kHz and the last Hz. For example
to tune to a radio station at 88.6 MHz we would enter 000.088.600.000 into the frequency input. To tune to 861.5475 MHz we would enter 000.861.547.500. To tune to 1.575 GHz we would enter 001.575.000.000. To
tune to 500 kHz (with an upconverter and appropriate offset shift set (discussed later)) we would tune to 000.000.500.000.

Volume Set the volume level of your output speakers or audio piping device here.
RF Spectrum /
This part of the window shows the RF spectrum as a graph in real time visually. Active signals will appear as peaks on this graph.
FFT Display
RF Waterfall This part of the window shows the RF spectrum graph spread over time with new data at the top and old data at the bottom, just like a waterfall.

The vertical red line in the RF spectrum graph shows where on the RF spectrum the RTL-SDR is currently tuned to. Within the currently active chunk of instantaneous bandwidth the tuning can be altered by simply
using the mouse to click and drag the red line, or just by clicking elsewhere in the RF spectrum.
Tuning Bar
The shaded rectangular area around the red line shows the bandwidth of the tuned area (don’t confuse this with the bandwidth/sample rate that is set in the configure menu). The bandwidth should be set so that it covers
the area of the signal that is tuned. The bandwidth can be adjusted by using the mouse to simply drag the edges of the shaded area in or out.

Radio Tab

Here you can choose what type of demodulation mode the signal at your currently tuned frequency should use.

2 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Mode Acronym Expansion Explanation

Narrowband Frequency
NFM Commonly used mode used by walkie talkie radios, weather radio and most VHF/UHF digital signals.
Modulation

WFM Wideband Frequency Modulation This is the mode that broadcast FM stations use (e.g. radio music stations).

Used by broadcast AM stations that are receivable by normal shortwave radios and also used by air band voice frequencies used by aircraft and air traffic control. Some digital signals also use
AM Amplitude Modulation
AM.

Lower Side Band / Upper

LSB/USB Used in the HF band by ham radio users to transmit voice and data efficiently with small bandwidths.
Sideband

CW Continuous Wave Used for listening to Morse code.

DSB Double Side Band Similar use to AM, but requires centered tuning.

RAW Raw IQ signal Used for listening or recording RAW IQ data

Setting Suggested Default Explanation

This box offsets the tuned frequency by the amount entered. This is useful if you are using an upconverter. For example if you have an upconverter with a 100 MHz oscillator, you would set the shift to
0 (No upconverter
Shift be -100,000,000 (don’t forget the minus sign). Without the shift, when using an upconverter to tune to a signal at 9 MHz you would need to actually tune to 100 + 9 = 109 MHz. With the shift set, you
used)
can tune to 9 MHz as normal. If you have an upconverter with a 125 MHz oscillator you would tune to 125 + 9 = 134 MHz, or set the shift to -125,000,000.

NFM/AM: 12500,
Bandwidth This is the width of the shaded part of the tunable area. You can set it manually here, or by dragging the edges with the mouse as described under the tuning bar description.
WFM: 250000

Changes the filter type used. Different filters have different shapes. The filter is used to select the highlighted signal in the RF window. Blackman-Harris is usually the best filter to choose and this setting
Filter Blackman-Harris 4
almost never needs to be changed.

Changes the filter order. You may notice when using low filter orders that signals outside of the tuned bandwidth can still be heard. Larger filter orders “tighten” or “sharpen” the band pass filter used
Order 500 within the tuned bandwidth/IF thus preventing signals outside of the tuned bandwidth from being heard. You will want to increase the filter order when there are strong signals near to your tuned area.
Using higher filter orders can cause a greater load on the CPU, so slow PCs may need to reduce this value.

Squelch is used to mute the audio when the signal strength is below the specified value. A larger value requires a stronger signal to unmute the audio. It is useful for when listening to speech as the sound
Squelch OFF
of static when no one is talking will be muted.

CW Shift 600 Mainly useful for when receiving CW (Morse code) as it specifies the offset between CW transmit and receive frequencies.

FM Stereo OFF Will enable stereo output for broadcast radio WFM signals, but can make weak stations sound worse.

In many bands frequencies are allocated at a fixed distance apart. For instance in most countries air band signals are spaced 25 kHz apart (or 8.33 kHz in some countries). Turning on snap to grid can
Snap to Grid / OFF or set to band
help with tuning by causing the tuning bar to snap directly to a signal. However, to use this with a non-TCXO RTL-SDR the PPM frequency offset correction must be set correctly, otherwise the
Step size spacing
frequencies may not line up. The snap to step size can be set in the “Step Size” pull down menu.

Correct IQ ON Should usually be selected as ON. This setting removes the small but annoying center spike that is present with R820T/R820T2 RTL-SDR dongles.

Only active in AM or DSB mode. Allows for synchronous AM which can significantly improve reception and also automatically centers the signal on the carrier. Turn this on for better AM reception,
Lock Carrier OFF
but may increase CPU usage.

Can be used when “Lock Carrier” is activated. Takes advantage of the symmetry of AM signals which helps with weak signals when they may be fading in and out. Turn this on for better AM reception,
Anti-Fading OFF
but may increase CPU usage.

Swap I & Q OFF If you are using SDR# as a panadapter, some hardware radios may have the I & Q signals swapped and need this option checked.

Mark Peaks OFF Simply marks any peak in the RF spectrum with a circle.

Audio Tab

This tab allows you to adjust settings related to the audio processing.

3 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Suggested
Setting Explanation
Default

Sample Sets the sample rate of your sound card. Some decoding software may require a specific sample rate to be set. Usually the default value should be fine for general listening. This is normally greyed out unless
48000
Rate using a sound card based SDR.

Specifies the input sound card when using SDR# with the “Other (Sound Card)” source. Used mainly with sound card based software defined radios. In normal use with an RTL-SDR this does not need to be
Input A Sound Card
set.

Output Speakers Sets the audio output device. By default it is set to your speakers. If you are passing the audio to a decoder program here you would choose your virtual audio pipe (VAC/VB Cable) to send the audio to.

Unity Gain OFF Should normally be unchecked as it sets the audio gain to 0 dB.

Filter
ON Improves voice signals by filtering the audio, removing high pitched hiss and DC noise. Should normally be off if decoding digital signals, but may actually help in some cases if there is significant DC offset.
Audio

AGC (Automatic Gain Control) Tab

Note that in some modes the AGC tab will be greyed out.

Suggested
Setting Explanation
Default

Turns on the audio automatic gain control. The AGC will attempt control the audio volume level so that loud sounds are not too loud and quiet sounds are not too quiet. The default settings work
Use AGC ON
well for voice audio signals. It is especially useful to turn this on when listening to AM/USB/LSB signals as strong signals in these modes may sound distorted otherwise.

Use Hang / Threshold /

-50, 100, 0 Allows you to modify the default AGC behavior, though in most cases the defaults are fine.
Decay / Slope

FFT Display

The FFT display settings adjust options related to the spectrum analyzer screen and the waterfall.

Suggested
Setting Explanation
Default

View Both Set it to view both the RF spectrum and the waterfall, or only one of them, or none at all. Removing the waterfall may be useful on older PCs with slow processing hardware.

Blackman-
Window Sets the type of windowing algorithm to use on the FFT, the default of Blackman-Harris 4 is the best in most cases.
Harris 4

Increasing the resolution will increase the quality of how the signal looks in the RF display and waterfall. Using a higher resolution may be useful when fine tuning, as high resolutions will allow you to see
Resolution 32768 the peaks and structure of a signal much more clearly. Beware that high resolutions can slow your PC down and can cause trouble especially with single core machines. Generally, a value of at least 32768
should be used if your PC can handle it.

Time Markers OFF Adds time markers on the waterfall display, so you know at what time a particular signal was broadcasting.

Gradient Allows you to customize the colors used in the waterfall display.

Mark Peaks OFF Adds a circular marker on every signal peak on the RF spectrum.

S-Attack /
Changes the amount of smoothing and averaging done in the RF spectrum display.
S-Decay

4 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

W-Attack /
Changes the amount of smoothing and averaging done in the waterfall display.
W-Decay

Speed Changes how fast the RF spectrum and waterfall updates.

Zoom FFT

Zoom FFT is a plugin that comes by default with SDR#. It creates a zoomed in RF spectrum display of the tuned IF bandwidth at the bottom of SDR#.

Setting Explanation
Enable
Opens a “zoomed in” RF spectrum graph around the area of your tuned IF bandwidth. Allows you to see the signal structure with much greater resolution.
IF

Enable
If Enable IF is checked, then you can enable a special adjustable IF filter. This filter allows you to filter the left and right side of the tuned IF bandwidth individually.
Filter

Enables you to see the MPX spectrum of a broadcast FM radio station. Broadcast FM is encoded in a special baseband audio format called MPX. It contains a mono section, a pilot tone and a stereo section, as well as sometimes
Enable
subcarrier sections for data like RDS and special radio services like SCA. If you were to try and view the audio baseband with the “Enable Audio” button, you wouldn’t see the MPX structure because SDR# would have
MPX
processed it into normal audio, and discarded the subcarriers and other sections.

Enable
Allows you to see the audio (baseband) spectrum.
Audio

SDR# Digital Noise Reduction

It is useful to turn on digital noise reduction when listening to weak and noisy analogue voice signals. This setting will attempt to reduce the background ‘hiss’ sound. There are two DNR options available, IF and Audio. The IF uses the
noise reduction algorithm on the IF signal and the Audio option does it on the output audio signal. Usually the IF digital noise reduction works best and should be tried first, though a combination of both may work best. The sliders control
the strength of the algorithm applied, and the profile can be optimized for the type of audio you are listening to. The profile options are Hi-Fi, Talk, Speech, Narrow Band and custom.

Noise Blanker

The noise blanker is an algorithm that can be turned on to help reduce impulsive and pulsing like noise from sources like spark gaps. Examples of this type of noise may come from motors, electricity lines, power over Ethernet and switching
power supplies. Carefully using this option can really help when receiving a weak signal amongst pulsating noise, which is mostly common on the HF bands. The noise blanker works by simply removing any samples that have large pulses
of energy in them.

In SDR# there are two different types of noise blanker. The baseband noise blanker works on the entire spectrum and will remove pulses from the FFT and waterfall, whereas the demodulator noise blanker only works within the tuned area
that is currently being demodulated. Tuning the settings is mainly an exercise in trial an error. Move the sliders until the pulsating noise goes away, whilst trying to keep the signal active.

Recording Tab

The recording tab allows you to make I/Q and Audio recordings. The sample format allows you to choose the level of recording quality needed. Since the RTL-SDR is only about 8-bits, we can select the lowest 8 Bit PCM option. Using only
8-bits saves a significant amount of disk space.

An I/Q recording is a recording of the entire ~2 MHz bandwidth that you are currently tuned to. It saves the RF data within the bandwidth so you can replay it at a later time. An I/Q recording can be made by checking the “Baseband” check
box. Note that I/Q recordings can use up a lot of disk space, so make sure to watch the File Size and Duration status counters. I/Q recordings can be played back in SDR# by selecting IQ File (*.wav) from the source menu. If you receive a lot
of dropped buffers, then your PC or disk may simply not be fast enough to process the recording. Remember that baseband recordings use a lot of disk space.

The audio coming out of the speakers can be recorded by checking the “Audio” check box. This will record audio to a standard audio .wav file. All recorded files are stored in the same folder as the SDR# executable.

5 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Frequency Manager Tab

The frequency manager allows you to save any frequencies of interest in a database. A new frequency can be added to the database by clicking in the New button. This will add a frequency with the current tuned frequency and settings like
bandwidth. You can edit the frequencies name and put it into a group for easy management. Double clicking on a stored entry will instantly tune SDR# to that frequency, and set the stored mode and bandwidth.

If you check the “Show on spectrum” check box then your saved frequencies will be displayed in the RF spectrum.

Right hand side sliders

The sliders on the right adjust the graph display settings for the RF spectrum and waterfall.

Suggested
Setting Explanation
Default

Moving this slider will cause the RF spectrum and waterfall to zoom in on your tuned IF bandwidth area in order to see a signal closeup. However, the more you zoom in, the lower the resolution will seem. An
Zoom Zoomed out alternative to zooming is to either reduce the sample rate, or to use the special decimation drivers. These alternative methods will preserve the visual resolution and allow you to see the signal structure much more
clearly.

Contrast Adjusts the contrast of the waterfall. Adjust it so that signals clearly stand out from the background noise.

Modifies the dB level range shown on the left (vertical) axis of the RF spectrum window. You should adjust this so that the noise floor sits near the bottom of the RF spectrum window. This will allow signals to be
more visible in the FFT RF spectrum and waterfall displays. As the RTL-SDR has a dynamic range of approximately 50 dB (plus a little more after oversampling/decimation), you will not need a range much higher
than 0 to -70 dB. This setting will also affect the contrast in the waterfall and may help make weak signals easier to spot.

Range -70

Adds an offset to the dB level range in the RF spectrum window. The offset is added to the top value on the dB level range in the RF spectrum. Usually there is no need to adjust this, but if you want to get really good
contrast on weak signals, adjust this along with the range so that the signal height is the same height as the vertical axis. This setting will also affect the contrast in the waterfall and may help make weak signals easier
to spot.

Offset 0

Configure Window / RTL-SDR Controller

The SDR# configure window can be accessed by clicking on the cog icon at the top of the SDR# window. The settings in this window affect the actual RF performance of the RTL-SDR, and should be set correctly to optimize the signal
to noise ratio (SNR). The configure window has several options which are described below.

Remember that some options may be greyed out until you press stop in SDR#.

6 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Setting Suggested Default Explanation

If you have multiple RTL-SDR dongles plugged in, the device drop down menu allows you to choose between them.
Device Your RTL-SDR

Lets you choose the size of the instantaneous bandwidth the RTL-SDR should display. Generally settings of up to 2.8 MSPS work well on most PCs, but if you have a slow PC
Sample Rate 2.048 or 2.4 MSPS
you may want to reduce this. We recommend a default rate of 2.048 or 2.4 MSPS.

Sampling Mode Quadrature Sampling Use Quadrature sampling for normal operation. The direct sampling selections should be used when using an RTL-SDR that supports it.

R820T/2 : OFF

Offset Tuning E4000/FC0012/13 : ON Only useful for the E4000/FC0012/13 tuners. Selecting this will get rid of the large spike in the center of the spectrum that is present with the E4000/FC0012/13 zero IF tuners.

RTL AGC OFF Enables automatic gain control on the RTL2832U chip. This is normally not useful as selecting this usually degrades reception.

Tuner AGC OFF Enables the automatic gain control system on the tuner chip. Can be useful for general browsing, but it is almost always better to set the gain manually.

RF Gain Adjust for best signal to noise ratio This slider can be used to set the tuner RF gain manually. Will not be active if Tuner AGC is checked.

TCXO Dongle: 0
Allows you to correct the frequency offset that RTL-SDRs have from having low quality crystal oscillators.
Frequency correction
(ppm) Standard Dongle: Adjust for freq.
accuracy.

Setting the RF Gain

There are three RF gain settings that can be found by clicking on the Configure button. RTL AGC turns on the RTL2832U chips internal automatic gain control (AGC) algorithm. Tuner AGC enables the RTL-SDR tuners AGC. The AGC’s
attempt to automatically optimize the SNR of the signals. Finally, the gain slider can be used to manually set the gain.

The AGCs used in the RTL-SDR are designed to be used with wideband DVB-T signals, and do not work very well with narrowband signals. We recommend using manual gain control at all times to optimize the gain of a signal, however
for casual browsing turning on Tuner AGC may suffice. RTL AGC is almost never used as it tends to just introduce a lot of unwanted noise.

The goal when setting the RF gain manually is to try and get the signal to noise ratio (SNR) as high as possible. This means that the maximum signal strength should be high, but the noise floor should also be as low as possible.

When increasing the gain, there will come a point at which the noise floor begins to rise faster than the signal strength rises. This is the point at which you should stop increasing the gain.

You can calculate the signal to noise ratio by subtracting the peak signal height from the height of the noise floor.

What Overload Looks Like

In SDR's (and all radio's for that matter), overload is when a signal that is too strong enters the radio and causes “saturation”. An analogy might be trying to listen to your friend talking to you at a loud concert. The music from the speakers is
so loud that you can't hear what they are saying. The same thing can happen in radios. For example if the SDR cannot cope with a strong signal and starts overloading, weaker signals will no longer be able to be heard. This can happen even
if there is a strong signal hundreds of MHz away from your target signal, though the closer in frequency it is the more problematic it will be. The biggest causes of overload are broadcast FM signals, pagers, TV broadcasts, DAB radio and
GSM signals.

The first solution to overload is to simply turn the gain down. But turning the gain down can also make your desired signal weaker, so ideally you'd use a filter to remove those unwanted strong signals, or buy a more expensive 12-bit or
higher SDR which can handle strong signals much better. In this section we'll show you what overload looks like on SDR#, so you'll know when to recognize if there is a problem.

Overload can manifest itself as images of the strong signal at frequencies where they're not meant to be. For example in the image below there are broadcast FM stations at 206 MHz, and they definitely should not be there. Simply turning
down the gain causes them to disappear.

7 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

BCFM Images

It can also manifest as a rise in the noise floor. For example in the image below a strong pager signal is causing the noise floor to rise whenever it transmits, and then fall again when it stops.

Pager Causing Noise Floor Rises

If you are tuned only a few MHz away from a very strong signal it can cause all sorts of weird images to show up . For example in this image below, whenever the pager transmits it causes strange signal spikes all over this part of the
spectrum.

Of course overload can also cause the noise floor to rise so high that the signal is no longer visible at all.

Pager Overload

SDR Sharp Plugins

There are many plugins available for SDR# that extend its functionality. We recommend visiting rtl-sdr.com/sdrsharp-plugins for a list and brief overview of these plugins.

To install plugins you will most often need to copy a .dll file to the SDR# directory and add a 'magic line' text entry to the Plugins.xml text file which can be found in the SDR# directory. You will need to open this file in Notepad or another
text editor to read it. The readme file that usually comes in the plugin zip file will usually tell you what the 'magic line' is. The line should be added between the <sharpPlugins> </sharpPlugins> tags.

Note that some older plugin readme files may still instruct you to add the line to the SDRSharp.exe.config file. This was used in older SDR# versions and is now incorrect. The line should be added to the plugins.xml file now.

If you enjoyed this tutorial you may like our eBook available on Amazon.

8 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

The Hobbyist's Guide to the RTL-SDR: Really Cheap Software Defined radio.

30 103 133
SHARES

Related Posts:

1. SDRSharp Frequency Manager Plugin updated to Version 1.4

2. Measurements on RTL-SDR E4000 and R820T DVB-T Dongles: Image Rejection, Internal Signals, Sensitivity, Overload, 1dB Compression, Intermodulation
3. SDRSharp Frequency Manager + Scanner v1.31 Update
4. Airspy Reception Tips and Tricks: Receiving Weak Signals with Strong Nearby Signals
5. New SDR# RTL-SDR Driver with LNA/Mixer/VGA Gain Settings and Decimation

Written by admin Posted in RTL-SDR Tagged with rtl-sdr, rtl2832, rtl2832u, sdrsharp

17 comments

1.

July 26, 2018 - 6:29 pm HarveyL

Is there any way of invoking SDR# in ‘play’ mode?

I’m running it on a remote machine so am not on site to click the ‘play’ triangle. I’m clicking it under s/ware control, but that’s not ideal as the computer is sometimes busy with updates etc.

Reply

2.

July 24, 2018 - 9:10 am Richard Rojas

regards
I want to install orbitron in the latest version of sdrsharp maybe someone could indicate how I could do it.

Reply

3.

July 12, 2018 - 7:07 pm Craig E Newby

Is there a way to update to latest revision of SDR# from an earlier (.1637) without doing a fresh install? I was hoping to retain all the settings, specifically freq.mgr . Thanks, Craig

Reply

July 12, 2018 - 8:55 pm Brightnoise

After installation of the Zadig driver you can run the version that you want. No need for un-install: just select the version that you want. Different subdirectories for different versions! I use more and newer versions and still
prefer version 1631. Brightnoise

Reply

July 13, 2018 - 3:08 pm Craig

Thanks for the reply. Im still missing something. I created a folder named sdr#1667 inside the main SDR# folder (current rev) and placed SDRSharp.exe (rev 1667) there. Nothing happens when I open the new rev. It works
fine with my rev 1637. Im not getting what you describe. Do I need to run zadig again for new revision? Thanks.

Reply

July 13, 2018 - 3:55 pm Timmy

I usually create a new folder for each release of SDR#

e.g.
I’d download sdrsharp-x86 rev 1667 and fully extract it to a new folder called sdrsharp-x86-v1667
And then I copy in “BandPlan.xml” and “frequencies.xml” because I customised mine.
I’d go about adding any plugins I use one at a time, to see which one are broken (if any) by newly added features. So then I know which plugins I need to wait on those developers to make releases.

And if anything is broken by the newest release or just does not work as I would expect, I still have my old folders with a fully functioning previous releases.

Reply

July 13, 2018 - 5:09 pm Craig

Got it ! Obvious once it worked! Im new to SDR# so its time to look at plug-ins. Thanks much.

Reply

4.

May 11, 2018 - 1:24 am OKCarl

I own two scanner radios popular in the 1990’s- AOR AR 3000A’s. Each radio has a port in the back for a 25 pin serial cable. Each has a switch on the backside labeled: Remote: on off. Are there options/settings somewhere in the
SDR# package that will allow me to link up SDR# with my old fashioned hardware? Is there a soldering iron kind of a fix I need to make on the circuit boards of my AOR AR 3000A’s to get them working with SDR#? There used to be
software packages built for my machines but they went out of fashion as digital became popular. Could I use SDR# as a kind of a ‘plug in’ in a software package purpose built for my AOR AR 3000A’s?

Reply

5.

May 10, 2018 - 9:57 pm Not-Brightnoise

9 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Can I use OmniRip to control my Yaesu FT-950 w/an RSP2?

Reply

July 12, 2018 - 8:57 pm Brightnoise

You are using a confusion name. Why?

Reply

6.

May 9, 2018 - 10:39 am Mario

SDR# is unquestionably the best program out there. Many of us got our start in the world of Software Defined Radio using a simple SDR dongle and SDR# which continues to improve with updates. And to boot, it’s free. Thanks to all
who were involved in developing this software program that’s brought SDR to the masses.

Reply

May 9, 2018 - 9:07 pm Bendail Vam

You must not have experienced sdr-console, because THAT is the definitive SDR “program” – w/GPU FFT accel, multiple receive slices, mutilple audio endpoints built in, and free (but you should def. donate, once you gasp at
the ‘why haven’t I been using this all along’ shock wears off).

Reply

May 11, 2018 - 12:48 pm Mario

Good point, I have downloaded this great program. It has a plethora of useful options (not a criticism!) the learning curve is a bit steep for me hi hi. One day I’ll sit down and finally work with it. And yes, if you have the
funds to donate, shake the piggy bank and do so.

Reply

7.

May 8, 2018 - 5:17 pm Brightnoise

Thank you! I see that the noise floor WITHIN the filter is estimated/measured as reference; even when the carrier has sidebands. I still see some things that I can’t understand; I will look further in it.

Reply

May 8, 2018 - 6:21 pm Brightnoise

Yes, your explanation is correct. For my measurements I need to have C/N in a specified bandwidth. The noise floor in the reading (not the S-meter reading, but the number on the right-hand side of the spectrum) is related to the
noise in the FFT bandwidth (one bin). This bandwidth is not specified: I need to recalculate it from the FFT-settings.When I change the resolution, the reading changes corresponding. As it should. There is always the need to
calculate the BIN bandwidth. Or do I oversee something simple….. My measurements are always related to radio bandwidth 3 kHz; I set the filter to that bandwidth and take the reading from the level indicator (left-hand pane).
Better suggestions? Please!

Reply

8.

May 8, 2018 - 1:33 pm Brightnoise

All is very well explained. Thanks. One question: what is the meaning of the number on the right-hand side of the spectrum display. In the figure “pager causes noise floor rises” above it is visible and gives value 3. In my application it
is changing the value continuously and I can’t get a logic explanation what it is measuring. Anybody?

Reply

May 8, 2018 - 2:43 pm Bertran

The level of the signal inside the highlighted IF in relation to the noise floor in dB.

Reply

Post a comment

Comment

You may use the following HTML:

<a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

Name Email Website

ANTISPAM: What does the 'A' in AM radio stand for? (Required)

Notify me of followup comments via e-mail. You can also subscribe without commenting.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Reading Household Wireless Utility Meters with an RTL-SDR and Plotting the Data in Home Automation Software
New SDR# Plugin Manager and Colorizer Available

10 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Follow Us

Weekly Newsletter

Search

Recent Posts

HydraSDR Preview: A 4x Coherent RTL-SDR for Direction Finding, Passive Radar and more
A Web and RTL-SDR Based Trunking Scanner
HDSDR Version 2.80 Beta Released
Using a HackRF SDR to Withhold Treatment from an Insulin Pump
Building a Tracking Mount for HRPT Weather Satellite Reception Part 2

Recent Comments

{ i got the same error, but eventually the file was created and it run without problems. it saves all the scan values in that file. } – Aug 19, 10:19 PM
mavallmo { Hola. He comprado este filtro, anteriormente ya compre el de FM, mi duda es, ¿hay una forma especifica de conectar estos filtros?, es decir, ¿tienen ... } – Aug 19, 4:18 PM
Danny Robinson VK6DVR { Danny VK6DVR Tracking meteor trajectories: I wonder how good this HydraSDR system would be at reporting the trajectory of meteors, but more particular, the much ... } – Aug 19, 11:52 AM
szpajder { Narrowband FM is supported since version 2.1.0, which has been released 2 years ago... } – Aug 18, 7:39 PM
{ actually laughing at the recall that people are atlkig about that UNIDEN AMERICA HAS TO DO TO REPLACE THE LIL TUNER CHIP INSide... No firmware ... } – Aug 18, 11:42 AM
TK { Damn this looks cool. Eagerly awaiting more news! } – Aug 17, 11:59 PM
Arthur Ripple { on the pre order web page there are many options available but I can not see enough info to decide what to order no links ... } – Aug 17, 2:44 PM
Older »

Polls

What do you mainly use your RTL-SDR / SDR for?

ADS-B
AIS
Trunked Radio
Police/EMS Scanner (P25/TETRA/Analogue)
Weather Satellites
HF Reception
Filter & VSWR Meter
L-Band Satellites
Radio Astronomy
Air Traffic Control
ACARS
Weather Balloons
Reverse Engineering
Monitoring Pagers
Amateur/Professional Research
VHF Amateur Radio (APRS/Voice etc)
Panadapter
General Signal Browsing
Passive Radar, Direction Finding, Coherent Experiments
Other

Vote

View Results

Polls Archive

Categories

Archives

Full Archives List

Tags

ads-b adsb AERO aircraft airspy airspy HF+ AIS amateur radio android antenna APT Automatic dependent surveillance broadcast DAB downconverter dsd E4000 gnu radio GPS GSM hackrf hdsdr HF inmarsat l-band limesdr linux LNA NOAA outernet plugins R820T radio
astronomy raspberry pi reverse engineering rtl-sdr rtl2832 rtl2832u satellite sdr# sdrplay sdrsharp security Software-defined radio upconverter weather satellite
Latest Forum Posts

RTL-SDR Discussion • DMR units position

RTL-SDR Discussion • Re: Sdr sharp tetra demodulator crash on startup
RTL-SDR Discussion • Popping noises
Other SDR Devices • Re: RSP1A with SDR# v1668
RTL-SDR Discussion • Re: SDR for xDSL spectrum analysis

11 of 12 19/08/2018 22:44
SDRSharp Users Guide https://www.rtl-sdr.com/sdrsharp-users-guide/

Submit a Story/Contact

Submit a Story/Contact

Meta

Log in
Entries RSS
Comments RSS
WordPress.org

What is RTL-SDR

The RTL-SDR is an ultra cheap software defined radio based on DVB-T TV tuners with RTL2832U chips. The RTL-SDR can be used as a wide band radio scanner. It may interest ham radio enthusiasts, hardware hackers, tinkerers and
anyone interested in RF.

Privacy Policy

12 of 12 19/08/2018 22:44