See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/323760334

Simulation of Static Synchronous Compensator (STATCOM) for Voltage Profile

Improvement

Article · July 2015

CITATIONS READS

4 2,039

2 authors, including:

Nasiru Bello Kadandani

Bayero University, Kano
10 PUBLICATIONS   5 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

Power Quality View project

All content following this page was uploaded by Nasiru Bello Kadandani on 14 March 2018.

The user has requested enhancement of the downloaded file.

Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

Simulation of Static Synchronous Compensator (STATCOM) for

Voltage Profile Improvement
Nasiru B. Kadandani1* Yusuf A. Maiwada2
1. Department of Electrical Engineering, Bayero University, Kano – Nigeria
2. Department of Electrical Engineering, Hassan Usman Katsina Polytechnic, Katsina – Nigeria

Abstract
Voltage profile improvement is a very important aspect of power quality and system stability. Flexible A.C
Transmission System (FACTS) devices have been developed to provide system stability thereby enhancing
controllability and increasing the power transfer capability. Static Synchronous Compensator (STATCOM) is a
member of FACTS devices used for voltage profile improvement as well as power quality improvement of the
net system. In this paper, a STATCOM is simulated in Simpower Simulink of MATLAB environment for
voltage regulation in a nominal π medium transmission line. The simulation results show that a STATCOM
without droop is a perfect voltage regulator and follows exactly the reference voltage. When the results are
compared to one with droop regulator, it was found that the sooner performs better than the later. However, the
droop extends the linear operating range of the STATCOM.
Keywords—STATCOM, FACTS, power quality, voltage regulation, grid

1. Introduction
Power quality is significant to both utility operators and consumers at all level of usage especially to non-linear
loads and sensitive devices placed in both industrial and domestic environment (Krishna & Reddy 2013). Power
quality refers to the proper characteristics of supply voltage and also a reliable and effective process for
delivering electrical energy to consumers. In other words, it is the power that enables equipment to work
properly (Srinivas & Reddy 2011). The measure of power quality depends on the nature and type of equipment.
Thus, power quality that is considered good for one equipment may not be good for another equipment. Hence,
power quality can be directly related to maintaining a smooth sinusoidal waveform of bus voltages at rated
frequency and also to be free from noise and harmonic distortion (Kumba & Sumanthi 2012). Therefore, any
deviation of magnitude, frequency or purity from the ideal sinusoidal voltage waveform can be considered as
power quality issue (Earnest & Wizelius 2011).
Binding standards and regulations are currently being imposed on suppliers and consumers, the
obligations to maintain the required power quality parameters at the point of interconnection, POI (Hiren et al
2010). These obligations become necessary due to the widespread use of power electronics equipments that are
sensitive in nature such as computers, converters, programmable logic controllers and energy efficient lightning
(Mohod & Aware 2011). These loads are very sensitive, hence, can lead to power quality disturbances such as
voltage dip, voltage swell, voltage flicker, voltage transient, and harmonic distortion. Among such disturbances,
voltage dip is the most dangerous one because it can leads to equipment failure, industrial shut down and
tripping of protection devices (Omar & AbdRahim 2008).
However, when good power quality is required, some kinds of compensation devices are necessary to
overcome the power quality disturbances (Kanaujia & Srivastava 2013). Thus, to restore the required power
quality, FACTS devices have been introduced (Das & Moharana 2012). Among such devices, STATCOM is the
latest development in that regard capable of interfacing between the utility and the consumer with the aim of
providing voltage profile improvement by compensating the reactive and harmonic power generated or absorbed
by the load (Khadem & Basu 2010). Thus, FACTS controllers provides an avenue for the regulation of
transmission of alternating current thereby increasing or diminishing the power flow in specific lines and
providing a quick response to stability problems (Mohanty and Barik 2014).

2. Static Synchronous Compensator (STATCOM)

Static synchronous compensator, popularly known as STATCOM is a shunt connected reactive power
compensation device used on alternating current electricity transmission network. It is capable of generating and
or absorbing reactive power and its output can be varied to control certain power parameters. It is a power
electronic based voltage source converter (VSC) that can act as either a source or a sink of reactive power in an
a.c power system.

1
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

Figure 1. Basic Configuration of a STATCOM

STATCOM is a member of FACTS devices used for voltage profile improvement. It makes use of VSC to inject
a compensation current of variable magnitude and frequency into the system at the bus PCC. It is thus a three
phase VSC with capacitance on its d.c link. STATCOM is thus a solid-state switching converter capable of
generating or absorbing independently controllable real and reactive power at its output when it is fed from an
energy source or energy storage device as its input terminal. The d.c voltage can be provided by a battery or an
energy-storage capacitor. The output of a STATCOM is a set of three phase voltage, each in phase and coupled
to the corresponding a.c system voltage through a small reactance. The reactance can be provided by a leakage
inductance of the coupling transformer or by an interface reactor. STATCOM is a very fast acting device that is
analogous to an ideal synchronous machine, which generates a balanced set of three sinusoidal voltages at the
fundamental frequency, with controllable amplitude and phase angle. It is based on VSC topology that utilizes
either Gate-Turn-off Thyristor (GTO), or Insulated Gate Bipolar Transistor (IGBT) devices. Thus, a STATCOM
is a VSC that converts a d.c input voltage into an a.c output voltage for active and reactive power compensation
(Kamarposhti & Alinezhad 2010).
In general, STATCOM can be operated to perform the following objectives:
• Voltage regulation
• Power factor correction
• Load balancing
• Harmonic compensation

3. Components of a STATCOM
STATCOM is basically comprised of four major components, namely
• Voltage source converter (VSC)
• Coupling transformer
• Controller
• DC energy storage

Figure 2. Basic Components of a STATCOM

2
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

3.1 Voltage Source Converter (VSC)

VSC is a power electronic device capable of generating a sinusoidal voltage of desired frequency, magnitude and
phase angle. It converts the d.c voltage across the storage device into a set of three phase a.c output voltages
(Sivakoti et al 2013). The voltages are in phase and coupled with the a.c system through the reactance of the
coupling transformer. The function of VSC as an integral part of STATCOM is to contribute in mitigating power
quality disturbances either by completely replacing the voltage or by injecting the missing voltage. The missing
voltage in this case is the difference between nominal and actual voltage. The VSC is usually based on some
kind of energy storage that will supply the d.c voltage. The desired voltage can then be obtained by switching the
solid state electronic devices in the converter circuit.

Figure 3. A three phase Voltage Source Converter

3.2 Coupling Transformer

Coupling Transformer is required to step down the system voltage to match that of the utility grid. A coupling
reactor is usually incorporated in order to filter out the current harmonic components that are generated by
pulsating output voltage of the VSC. The AC voltage difference across the leakage reactance produces reactive
power exchange between the STATCOM and the power system, in such a way that the AC voltage at the bus bar
can be regulated to improve the voltage profile of the power system, which is the primary duty of the
STATCOM. Alternatively, a secondary damping function can be added into the STATCOM to enhance power
system oscillation stability.

3.3 Controller
The controller performs feedback control and outputs a set of switching signals to drive the main semiconductor
switches of the power converter. It generates switching signal for the STATCOM to enable the STATCOM
injects a reactive current into the grid to behave as an over-excited synchronous generator (or capacitor) thereby
supporting the grid voltage or absorbs reactive current and behave like an under-excited synchronous generator
(or inductor) and tends to decrease the grid voltage. The STATCOM compensator is varied according to the
control strategy (Tajavoth et al 2013).
The main function of the controller is to maintain the voltage magnitude constant at the point where sensitive
load is connected, under system disturbances. It does this by measuring and comparing the r.m.s voltage at the
load point with the reference voltage. The difference between the two values is the error signal which serves as
input to the controller. The output is the power angle δ which is provided to the PWM signal generator. Thus, the
processed error signal generates the required power angle, δ, that will drive the error to zero, thereby restoring
the r.m.s value of the load voltage to the reference voltage value.

Figure 4. Block Diagram of a STATCOM Controller

3.4 DC Energy Source

The d.c voltage source can be provided by a capacitor connected on the d.c side of the VSC or by a battery
energy storage system (BESS). The dc energy source is connected in parallel with the d.c capacitor. It carries the
input ripple current of the converter. The capacitor can be charged by the VSC or by BESS. The function of the
BESS is to support the real power source under power fluctuating condition. Thus, in order to achieve the
required voltage regulation, the BESS is connected in parallel to the d.c capacitor of the STATCOM thereby
making it as energy storage element. The BESS will then inject or absorbs the reactive power required to
stabilize the grid system while maintaining the d.c capacitor voltage constant. In other words, it charges and
discharges to improve the voltage profile. Thus, the d.c energy storage is responsible for supplying and
absorbing the real power that is being exchanged by the transmission system at its d.c terminals (Malarvizhi &

3
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

Baskaran 2010).

Figure 5. DC Energy Source

4. STATCOM Topology for Voltage Profile Improvement

STATCOM generates a set of balanced three phase sinusoidal voltages at the fundamental frequency, with
rapidly controllable amplitude and phase angle (Appala-Naranya et al 2013). In other words, the VSC in the
STATCOM generates a controllable AC voltage source behind the leakage reactance. This voltage is compared
with the AC bus voltage of the system; if the voltage magnitudes are equal, the reactive power exchange is zero.
If the VSC voltage magnitude is higher than that of the AC bus voltage magnitude, the AC system sees the
STATCOM as a capacitance connected to its terminals. Conversely if the VSC voltage magnitude is lower than
that of the AC bus, the A.C system sees the STATCOM as an inductance connected to its terminals (Usha &
Kumar 2013).
Consider the following Figure:

Figure 6. Single line diagrem of a STATCOM

Where
E = System voltage (Line voltage of the transmission line)
V = Voltage generated by the VSC
X = Equivalent reactance of the coupling transformer
δ = Phase angle of E with respect to V
P = Active power dissipated in the system
Q = Reactive power generated or absorbed by the STATCOM

The active power, P and reactive power, Q, can be expressed in terms of the system voltage, converter voltage
and the reactance of the coupling transformer (Nazrul-Islam & Kazushige 2013):

δ (1)
δ (2)

While the phase angle, δ is given as:

δ (3)
The STATCOM based current controlled VSC injects compensation current into the grid thereby making the
source current harmonic free with a corresponding shift in the phase angle with respect to the source voltage to a
desired value. The injected current will then cancel out the reactive and harmonic parts of the load and induction
generator current, thereby improving the voltage profile. Thus, the impedance of the shunt controller, which is
connected to the line voltage, causes a variable current flow, and hence, represents an injection of current into
the line. If the STATCOM has a DC source such as BESS or an energy storage device like capacitor on its DC
side, it can supply real power to the power system. This can be achieved by adjusting two parameters, namely;
the phase angle of the STATCOM terminals (or VSC) and the phase angle of the AC power system. If the phase
angle of the AC power system lags that of the VSC, the STATCOM supplies real power to the AC system.
Conversely, if the phase angle of the AC power system leads the VSC phase angle, the STATCOM absorbs real

4
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

power from the AC system. The main function of the BESS is to serve as an energy storage element purposely
for voltage regulation and to keep the d.c capacitor voltage constant.
The STATCOM can be operated in two modes of operation as under
• In voltage regulation mode (the STATCOM voltage is maintained within specified limits)
• In VAR control mode (the STATCOM reactive power , Q is maintained at a fixed value)
In voltage regulation mode, the STATCOM implements the following V-I characteristic:

Figure 7: V-I Characteristics of a STATCOM in Voltage Regulation Mode

The voltage is said to be regulated at the reference value,Vref, provided the compensation current, I stays within
the minimum and minimum current values (-Imax, Imax) imposed by the converter rating. However, in order to
extend the linear operating range of the STATCOM, a voltage droop is normally used (usually between 1% and
4% at maximum reactive power output), and the V-I characteristic has the slope depicted in Figure 10. In the
voltage regulation mode, the V-I characteristic is described by the following equation:
+ (4)
Where = Positive sequence voltage (pu)
= Compensation current (pu/Pc)
= Slope or droop reactance
Pc = Three phase power of the converter

STATCOM has no moving parts; hence, it generates or absorbs reactive power at a faster rate than other FACTS
devices. It is capable of generating as well as absorbing reactive power thereby regulating the voltage profile of
the bus to which it is connected.

5. Simulation Results and Discussion

The entire system is simulated in Simpower Simulink of MATLAB environment. It consists of a 100MVA
STATCOM located at the centre of a nominal medium transmission line. The control parameters of the
STATCOM were first set to voltage regulation mode without any droop. The system reference voltage (i.e the
p.u voltage used by the regulator) was initially set to 1p.u and decreased to 0.98pu at t = 0.3s. It is further
increased to 1.02pu at t = 0.6s and finally brought back to 1p.u at t = 0.9s.

5
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

Figure 8: Simulink Diagram of a STATCOM for Voltage Regulation

5.1 Null Droop Condition
It can be seen from Figure 9a that under null droop condition, the STATCOM measured voltage, Vm follows the
reference value, Vref. This implies that STATCOM is a very good voltage regulator. Figure 9b shows the
reactive power absorbed/generated by the STATCOM, Qm together with the reference one, Qref. Positive value
of Qm represents the reactive power absorbed by the STATCOM while negative value indicates the reactive
power generated. The two Figures certify that the STATCOM absorbs reactive power when the A.C system
voltage rises and generates reactive power when the A.C system voltage falls.
Measured Voltage, Vm with Reference Voltage, Vref
1.025
Vm
1.02 Vref

1.015

1.01
Vm(p.u), Vref(p.u)

1.005

0.995

0.99

0.985

0.98
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Time(s)

Figure 9a. STATCOM Measured and Reference Voltage under Null Droop Condition
Reactive Power Generated/Absorbed, Qm with Reference Value, Qref
0.5
Qm
0.4 Qref

0.3

0.2
f(p.u)

0.1
.u), Qre

0
m(p

-0.1
Q

-0.2

-0.3

-0.4

-0.5
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Time(s)

Figure. 9b. Reactive Power Absorbed/Generated by the STATCOM with Reference Value under Null Droop
Condition

5.2 Droop Condition

Figure 10a shows the STATCOM measured and reference voltage (Vm and Vref) under droop condition.

6
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

Specifically, a droop of 2% was set. The corresponding reactive power, Qm absorbed/generated by the
STATCOM is shown in Figure 10b. It can be seen from Figure 10a that, because of the droop, the STATCOM
measured voltage, Vm does not follow the reference value, Vref perfectly.
Measured Voltage, Vm with Reference Voltage, Vref
1.025
Vm
1.02 Vref

1.015

1.01
Vm(p.u), Vref(p.u)

1.005

0.995

0.99

0.985

0.98
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Time(s)

Figure 10a. STATCOM Measured and Reference Voltage under Droop Condition
Reactive Power Generated/Absorbed, Qm with Reference Value, Qref
0.4
Qm
0.3 Qref

0.2
Qm(p.u), Qref(p.u)

0.1

-0.1

-0.2

-0.3

-0.4
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Time(s)

Figure 10b. Reactive Power Absorbed/Generated by the STATCOM with Reference Value under Droop
Condition

5.3 During Fault Condition

Figure 11 shows the measured voltage and the reactive power generated by the STATCOM when a remote fault
is applied. It can be seen from the Figure that the STATCOM generates reactive power in order to provide
voltage support to the system during the fault period.
Measured Voltage, Vm and Reactive Power Generated by the STATCOM, Qm
1.5
Vm
Qm
1

0.5
Vm(p.u), Qm(p.u)

-0.5

-1

-1.5
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Time(s)

Figure 11. Measured Voltage and Reactive Power Generated by the STATCOM

7
Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol.6, No.7, 2015

5. Conclusion
The paper has presented a technological review of STATCOM for voltage profile improvement. Its basic
structure, configuration, component parts and topology were also presented. Simulation results reveal that
STATCOM is an excellent voltage regulator especially when operated without droop. It can provide both
capacitive and inductive compensation. It has the capability of controlling output current over the rated
maximum capacitive or inductive range independent of the a.c system voltage and it has increased transient
rating in both capacitive and inductive operating regions as well as maintaining full compensating current at
depressed line voltage.

References
Krishna, A.R, & Reddy, K.R (2013), “Power Quality Problems and its Improvement Using FACTS Devices”,
Int. Journal of Engineering Trends and Technology”, Vol.4, Issue 5, May 2013, pp 1462 – 1466
Srinivas, D., & Reddy, M.R.S. (2011), “Power Quality Improvement in Grid Connected Wind Energy Systems
Using FACTS Devices and PID Controller”, IOSR Journal of Engineering, Vol.2, Issue 11, November
2011, pp 19-26
Kumbha, V., & Sumanthi, N. (2012) “Power Quality Improvement of Distribution Lines Using DSTATCOM
Under Various Loading Conditions”, Int. Journal of Modern Engineering Research, Vol.2, Issue 5,
September – October 2012, pp 3451 – 3457
Earnest, J., & Wizelius, T. (2011) “Wind Power Plants and Project Development”, PHI Learning Private
Limited, New Delhi,
Hiren, P., Krishna, V., & Roy, R. (2010) “Shunt Compensation for Power Quality Improvement Using a
STATCOM Controller”, ACEEE Int. Journal on Electrical and Power Engineering, Vol.1, Issue 2, July
2010, pp. 40-44
Mohod, S.W., & Aware, M.V. (2011) “Power Quality Issues and its Improvement in Wind Energy Generation
Interface to Grid System”, MIT Int. Journal of Electrical and Instrumentation Engineering, Vol.1, No.-
2, August 2011, pp 116-122
Omar, R., & Abd Rahim, N., (2008) “Modeling and Simulation for Voltage Sags/Swells Mitigation Using
Dynamic Voltage Restorer (DVR)”, Australasian Universities Power Engineering Conference, pp 1- 8
Kanaujia, M.K., & Srivastava, S.K. (2013) “Power Quality Enhancement with D-STATCOM Under Different
Fault Conditions”, Int. Journal of Engineering Research and Applications”, Vol.3, Issue 2, March –
April 2013, pp. 823 – 833
Das, S.K., & Moharana, J.K. (2012) “Design and Simulation of Small Signal Model of a STATCOM for
Reactive Power Compensation on Variation of D.C Link Voltage”, Int. Journal of Engineering and
Innovative Technology, Vol.2, Issue 5, November 2012, pp. 134 – 140
Khadem, S.K., Basu, M., & Conlon, M.F. (2010) “Power Quality in Grid Connected Energy System: Role of
Custom Power Devices”, International Conference on Renewable Energies and Power Quality”, March
2010.
Mohanty, A.K., & Barik, A.K. (2014)“Power System Stability Improvement Using FACTS Devices”, Int.
Journal of Modern Engineering Research, Vol.1, Issue 2, pp. 666 – 672
Kamarposhti, M.A., & Alinezhad, M., (2010) “Comparison of SVC and STATCOM in Static Voltage Stability
Margin Enhancement”, Int. Journal of Electronics Engineering, Vol.4, Issue 5, pp. 323 – 328
Sivakoti, K.K., Kumar, Y.N., & Archana, D. (2013) “Power Quality Improvement in Distribution System Using
D-STATCOM in Transmission Lines”, Int. Journal of Engineering Research and Application, Vol.1,
Issue 3, pp. 748 – 752
Tajavoth, C., Trishulapani, M., Mohan-Rao, V.K.R., & Yambabu, Y. (2013) “Power Quality Improvement for
Grid Connected Wind Energy System Using STATCOM Control Scheme”, IOSR Journal of
Engineering, Vol.3, Issue 7, July 2013, pp. 51 – 57
Malarvizhi, K., & Baskaran, K. (2010) “Enhancement of Voltage Stability in Fixed Speed Wind Energy
Conversion System Using FACTS Controllers”, Int. Journal of Engineering Science and Technology,
Vol.2, Issue 6, pp. 1800 – 1810
Appala-Narayana, C.H., Annanth, D.V.N, Syam-Prasad, K.D, Saibabu, C.H, Saikiran, S., & Papi-Naidun, T.
(2013) “Application of STSTCOM for Transient Stability Improvement and Performance
Enhancement for a Wind Turbine Based Induction Generator”, International Journal of Soft
Computing and Engineering, Vol.2, Issue 6, January 2013, pp. 158 – 163
Usha, N. & Kumar, M.V (2013) “Enhancement of Power Quality in Thirty Bus System Using ZSI Based
STATCOM”, Int. Journal of Modern Engineering Research, Vol.3, Issue 2, March – April 2013, pp.
773 – 778
Nazrul-Islam, M. & Kazushige, Y. (2013) “Design and Simulation of STATCOM to Improve Power Quality”,
Int. Journal of Innovation and Applied Sciences, Vol.3, No-3, July 2013, pp 871 – 878

8
 The IISTE is a pioneer in the Open-Access hosting service and academic event management.
The aim of the firm is Accelerating Global Knowledge Sharing.

More information about the firm can be found on the homepage:

http://www.iiste.org

CALL FOR JOURNAL PAPERS

There are more than 30 peer-reviewed academic journals hosted under the hosting platform.

Prospective authors of journals can find the submission instruction on the following
page: http://www.iiste.org/journals/ All the journals articles are available online to the
readers all over the world without financial, legal, or technical barriers other than those
inseparable from gaining access to the internet itself. Paper version of the journals is also
available upon request of readers and authors.

MORE RESOURCES

Book publication information: http://www.iiste.org/book/

Academic conference: http://www.iiste.org/conference/upcoming-conferences-call-for-paper/

IISTE Knowledge Sharing Partners

EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open

Archives Harvester, Bielefeld Academic Search Engine, Elektronische Zeitschriftenbibliothek
EZB, Open J-Gate, OCLC WorldCat, Universe Digtial Library , NewJour, Google Scholar

View publication stats