Application Note

1606-XLDNET4
• World-wide approvals ( )
for industry
• Input: AC 230V/115V, DC 210...375V • No switch-off at overload
• Output: 24V/4 A • Wide-Range Input
• 100 VA Limited Power Source • Robust mechanics and EMC
Input Output
Input voltage AC100...120/200...240V (switchable), 47...63 Hz Output voltage 24V DC +5% –1%
(85...132VAC / 176...264VAC, 210...375VDC,
see also“Output: Continuous Loading”) Output noise Radiated EMI values below EN50081-1, even when
Wide-Range Input: With the switch in the 230V position the power-supply unit op- suppression using long, unscreened output cables.
erates at low and moderate loads (up to 2 A) at any input voltage between 95 and Ambient temperature range Operation: -10°C...+70°C (>60°C Derating)
264VAC. Tamb Storage: -25°C...+85°C
Note: At DC input, always leave the switch in the 230V position
Input current < 2.0 A (switch in 115V position) Continuous loading Switch AC/DCin Iout
< 1.1 A (switch in 230V position)
(Tamb = -10°C...+60°C, 230V 176...264V ACin 4A
convection cooling), see also 95...176V ACin 3A
DCin at open output typ. 5 mA (preserves battery sources) diagram
For start at Tamb<0°C and low 210...375V DCin 4A
Inrush current typ. < 15 A at 264V AC and cold start input voltage, please contact 150...210V DCin 3A
If you intend to protect the primary side of the power supply with a fuse or a circuit Rockwell Automation. 100...150V DCin 2A
breaker, a 10 A slow acting fuse (HBC) or a supplementary protector 1492- 115V 85...132V ACin 4A
SPU1C100 is recommended. In order to meet local requirements, please consult lo- Output is protected against short circuit, open circuit and overload.
cal codes and regulations for proper installation..
Transient Transient resistant acc. to VDE 0160 / W2 Derating typ. 3 W/K (at Tamb=+60°C...+70°C)
handling (750V / 1.3 ms), for all load conditions.
Voltage regulation better 2% Vout over all
Hold-up time > 20 ms at 196VAC, 24V/4 A
(see diagram) Ripple / Noise < 25 mVPP (20 MHz bandwidth, 50 Ω measurement)
Overvolt. protection typ. 29V
Efficiency, Reliability etc. Parallel operation yes

Efficiency typ. 88 % (230V AC, 24V/4 A) Power back immunity 26V

Losses typ. 13.6 W (230V AC, 24V/4 A) Front panel indicator Green LED on front panel,
Life cycle (electrolytics) The unit exclusively uses longlife electrolytics, speci- goes out at Vout < 12 V
fied for +105°C.
Start / Overload Behavior
Construction / Mechanics
Start-up delay typ. 0.1 s
Housing dimensions and Weight
• WxHxD 65 mm x 124 mm x 102 mm (+ DIN rail) Rise time appr. 5...30 ms, depending on load
• Free space for above/below 25 mm recommended Overload behavior Unit fulfills the requirements under Ltd. Power Source
ventilation left/right 15 mm recommended acc. to EN60950, para. 2.11, as follows:
• Weight 620 g
• Pout < 100 VA at all load conditions
Design advantages:
• Iout < 8 A at all load conditions
• All connection blocks are easy to reach as mounted at the front panel.
• Input and output are strictly apart from each other and so cannot be mixed up (In-
put below, output above).
Wire Size Input/Output:
• Stranded 20...10 AWG (0.5...4 mm²), Solid 20...10 AWG (0.5...6 mm²)
Tightening Torque: 7 lbs in (0.8 Nm) recommended

1 Publication 1606-AP031A-EN-E March 2003

 2 Application Note
Output Current over Input Voltage (min.) Output characteristic (min.)

6
DCin 25
Output current Iout [A]

UL Limited Power
4 Source Class 2
20 P max 100 W
2 Imax < 8A

Output voltage Vout [V]

210
375 15
100 200 300 400
Input voltage DCin [V]

6 10
ACin
Output current Iout [A]

switch at 115V
4 switch at
230V 5

95 0
85 132 176 264 0 2 4 6 8 10
100 200 300 400
Input voltage ACin [V] Output current Iout [A]

Efficiency (min.)

90 90
89 89
88 88
87 87
Efficiency [%]

Efficiency [%]

86 86
85 85 176 VAC
84 85 VAC 84 230 VAC
83 115 VAC 83 264 VAC
82 132 VAC 82
81 81
80 80
1 2 3 4 5 1 2 3 4 5
Output current Iout [A] Output current Iout [A]

Hold-up time (min.)

100 100

90 90 switch pos. Iout=2A

Iout=2A 115V
80 80
Iout=2A 70 Iout=3A
Hold-up time [ms]

70
Hold-up time [ms]

Iout=3A
60 60
Iout=3A 50
50
40 switch pos. Iout=4A
40 230V
Iout=4A 30
30
20 20
10 ACin
10 DCin
0 0
90 110 130 150 170 190 210 230
130 170 210 250 290 330 Input voltage VACin [V]
Input voltage VDCin [V]

Specifications valid for 230V AC input voltage, +25°C ambient temperature, and 5 min
www.rockwellautomation.com run-in time, unless otherwise stated. They are subject to change without prior notice.
Corporate Headquarters
Rockwell Automation, 777 East Wisconsin Avenue, Suite 1400, Milwaukee, WI, 53202-5302 USA, Tel: (1) 414.212.5200, Fax: (1) 414.212.5201

Headquarters for Allen-Bradley Products, Rockwell Software Products and Global Manufacturing Solutions
Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe: Rockwell Automation SA/NV, Vorstlaan/Boulevard du Souverain 36-BP 3A/B, 1170 Brussels, Belgium, Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, 27/F Citicorp Centre, 18 Whitfield Road, Causeway Bay, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846

Headquarters for Dodge and Reliance Electric Products

Americas: Rockwell Automation, 6040 Ponders Court, Greenville, SC 29615-4617 USA, Tel: (1) 864.297.4800, Fax: (1) 864.281.2433
Europe: Rockwell Automation, Brühlstraße 22, D-74834 Elztal-Dallau, Germany, Tel: (49) 6261 9410, Fax: (49) 6261 1774
Asia Pacific: Rockwell Automation, 55 Newton Road, #11-01/02 Revenue House, Singapore 307987, Tel: (65) 351 6723, Fax: (65) 355 1733

Publication 1606-AP031A-EN-E March 2003  2003 Rockwell International. All Rights Reserved. Printed in US