®

PARAMAX
The Cooling Tower Drives
SFC Series

CW21

No. G2201E-2.1 No. G2201E-2

Issued 2009.12
 Features

Optimised for cooling tower use

1 Selection Criteria
● The SFC Series was specifically designed for the Motor Size vs. Fan Speed Input Speed 1800r/min
Fan Speed 285 253 225 200 180 160 144 128 112 100
r/min
cooling tower environment. Reduction 6.3
Ratio
7.1 8 9 10 11.2 12.5 14 16 18
55
● Use the chart to find the correct size based on motor 75
size and fan speed. 90

Motor (kW)
110
132
160
200
250
280

Gearbox SFC045 SFC055 SFC060 SFC065 SFC070 SFC075

Size
∗Refer to the selection table on page 5 for detatils.
2 Low Vibration Design
● Extended Bearing Span
Even if the cooling fan is balanced, excess vibration can occur
during operation.
Using an extended fan drive shaft (gearbox low speed shaft),
Extened Bearing Span
run-out due to fan operation is significantly reduced.
● Balanced Mounting Load
By arranging the mounting bolt holes uniformly about the Flat Mount Design
Backstop (Optional) Flat Mount Design
fan drive shaft, the load to the gearbox mounting base is Backstop
Oil Pump (Optional)
(Optional)
Oil Pump (Optional)
transmitted uniformly.
Fan Weight and
Thrust Load

3 Flat Mount Design

The SFC gearbox is designed without protrusions beneath the
mounting surface, leading to simple mounting base design and
construction.
The design also takes into account the use of an optional Uniform Mounting Load
backstop and pump to be added without protruding beneath the
Symetric Mounting Holes
mounting surface.

4 Thermally Efficient Design

Due to the gearbox location in a cooling tower, minimal airflow
from the cooling tower fan reaches it.
The SFC gearbox is designed with maximum heat dissipation in mind.
● Maximized Surface Area
● High Efficiency Gearbox Cooling Fan

With a Gearbox Cooling Fan Without a Gearbox Cooling Fan

(SFC Series)

Stagnant Air

Forced Cooling

Cooling Fan

Air Flow Around the Gearbox

090624_SFC Series_E.indd 2 2009/12/15 17:34:57

 Features

Low Noise
6 ～ 8dB（A）Noise Reduction From Previous Series
6 to 8dB (A) noise reduction from previous series achieved with 3D tooth surface modification in the
input stage bevel gear of reducer, enabling usage in environment with strict noise restriction.

Noise Level Noise Level of SFC Series

(Noise Level at 1m from Reducer Side)
Condition: Input Speed at 1,500r/min with Cooling Fan

Previous Model

Low Noise Model

Modification is made for optimal tooth contact

under load through simulation.
Motor Power

Ease of Maintenance
External Oil Gage Pipe
● 1 Year Maintenance free operation.
Oil Fill
Pipe Threads
● Gearbox is drilled and tapped for attachment of Air Breather
external air breather and oil fill/drain. Fan Stack
Inspection
● Internal gearbox inspection possible without Cover
draining oil due to inspection cover location
above operating oil level.
● Using internal splash oil lubrication, use of an Oil Drain
oil pump and its periodic replacement is not
required.

Available Accessories
Oil Seal Hood (Output Shaft)
Cooling Tower specific accessories are standard Oil Splasher
(Splash Lubrication)
equipment. Cooling Fan

Standard Equipment Options

Integral Cooling Fan Backstop *
Oil Seal Hood (Output Shaft) Oil Heater
Oil Gauge Oil Pump
Oil Gauge
Magnetic Plug Flow Switch
Magnetic Plug
Oil Level Switch Backstop (optional)
Dust-free Air Breather Oil Pump (optional)
Vibration Sensor Seat

* Use of a backstop (optional) is to prevent reverse rotation of the cooling fan. Backstop uses the internal gear oil for lubrication. Grease lubrication
type is also available.

Table of Contents

● Features ..............................1 ● Allowable Thrust Load (kW) .....8

● Nomenclature ......................3 ● Selection Procedure (HP) ........9
● Painting Specifications ........3 ● Mechanical Rating Table (HP) ...11
● Standard Specifications ......4 ● Allowable Thrust Load (HP) ...12
● Lubricant Specifications ......4 ● Application Data Sheet ..........13
● Selection Procedure (kW) ...5 ● Dimensions ............................14
● Mechanical Rating Table (kW) ....7

090624_SFC Series_E.indd 3 2009/12/15 17:35:00

 Standard Specification

Nomenclature

SFC 065 R2 G S RR F 14

Output Torque Gear Shaft Nominal

Series Size (kNm) Suf fix 1 Suf fix 2
Stages Arrangement Ratio

6.3
F : With Cooling Fan
7.1
(Standard)
045 (10.0) R2 S : Splash 8
055 (18.0) (Standard) 9
Right Angle FB : With Cooling Fan &
060 (21.7) G RR 10
SFC 065 (27.5) Double Backstop
11.2
070 (35.5) Reduction P : Shaft Driven 12.5
075 (44.0)
N : No Additional Cooling
Pump 14
16
NB : With Backstop
18

Painting Specifications
Valuation basis：◎･･･ Excellent，○･･･ Good
Weather-
Kind of painting Paint Specification Water Acid Alkali Heat
Painting ability of
Classification Resis- Resis- Resis- Resis-
area Paint of finish Thickness finished
Classification Type Quality tance tance tance tance coat
coat μm
Under
20-40 Modified alkyd resin
Standard Corrosion Acrylic modified
Coating
Paint Resistance phthalic ○ ○ ○ ○ ○
Finish Acrylic modified alkyd
30-60
Coating resin

Heavy Duty Under Special permeability

Corrosion
40-80
Coating epoxy aluminium paint
Humidity Thick film
Resistant
Resistance epoxy ◎ ◎ ◎ ○ ○
Outside Paint 1 Finish
120-240 Polyamide epoxy
Paint* (Option) Coating

Under Special permeability

40-80
Coating epoxy aluminium paint
Heavy Duty Humidity
Corrosion Resistance Second
120-240 Polyamide epoxy
Resistant & Polyurethane Coating ◎ ◎ ◎ ○ ◎
Paint 2 Weather-
(Option) ability
Finish Polyisocianate urethane
20-40
Coating resin paint

Inside Standard Oil

Paint Paint Resistance
ー ー 20-40 Modified alkyd resin ー ー ー ー ー

* One layer of modified alkyd resin paint as the first primer.

090624_SFC Series_E.indd 4 2009/12/15 17:35:01

 Standard Specification

Standard Specifications

Item Standard Specification

Material Spec. : Alloy Steel
Gear Heat Treatment : Case Hardening
Processing : Precision Finish
Type ： Roller Bearing
Bearing Rated Life (L10) : Low Speed Shaft Bearing ･････････････････････ 100,000 Hours or Longer
High Speed Shaft/Intermediate Shaft Bearings ･･･ 50,000 Hours or Longer
Shaft Material Spec. ： Alloy Steel
Housing Material Spec. ： Cast Iron
Gearbox
Housing and Cover Mating surfaces : Liquid Sealant
Seal Low Speed Shaft ： Dust-lip Oil Seal and Seal Hood
High Speed Shaft : Dust-lip Oil Seal
Oil Splash Lubrication
Lubrication An oil splasher attached to the high speed shaft propels oil from the lower oil reservoir to
the upper bearing oil reservoir.
Paint P3 Reference
Rotation Speed High Speed Shaft input speed: 450 to 1800r/min
Ambient
0℃ to 40℃
External Temperature
Conditions Environment Not designed for corrosive or explosive gas environments.
Altitude Designed for altitudes of 1000m or less.

Lubricant Specifications

● Mineral Oil
EXXON TOTAL
Brand ARAL BP CASTROL CHEVRON GULF OPTIMOL SHELL TEXACO THIBOL
MOBIL FINA ELF

GEAR MOBIL-
ISO VG320 DEGOL ENERGOL ALPHA EP LUBRI- OPTIGEAR OMALA MEROPA CARTER THIBOL
COMPOUNS GEAR 600
AGMA 6EP BG320 GR-XP-320 SP320 CANT HD320 BM 320 320 WM 320 EP320 1100/320
EP320 XP320

● Synthetic Oil

Brand EXXONMOBIL

MOBIL GEAR
ISO VG320 MOBIL GEAR
SHC XMP
AGMA 6S SHC 320
320

090624_SFC Series_E.indd 5 2009/12/15 17:35:01

 Selection Procedure

Quick Selection Table kW

● Input Shaft Speed 1750r/min
Fan Speed
280 245 220 195 175 155 140 125 110 97
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
55 ※ ※ ※ ※ ※ 045 045 ※ ※ ※
75 ※ 045 045 045 045 045 045 055 055 055
90 ※ 045 045 045 045 055 055 055 055 055
110 ※ 045 045 055 055 055 055 055 055 060
Motor
132 ※ ※ 055 055 055 055 055 060 065 065
(kW)
160 ※ ※ 055 055 055 060 060 065 070 070
200 ※ ※ ※ 060 060 065 065 070 075 075
250 ※ ※ ※ ※ 065 070 070 075 075 ―
280 ※ ※ ※ ※ ※ 070 075 075 ― ―

● Input Shaft Speed 1160r/min

Fan Speed
185 165 145 130 115 105 93 83 73 64
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
55 ※ 045 045 045 045 055 055 055 055 055
75 ※ 045 045 055 055 055 055 055 055 060
90 ※ ※ 055 055 055 055 060 060 065 070
110 ※ ※ 055 055 055 060 065 065 070 070
Motor
132 060 060 060 060 060 065 065 070 075 075
(kW)
160 060 060 060 065 065 065 070 070 075
200 065 065 065 065 070 075 075 075
250 065 070 070 075 075 075
280 075

● Input Shaft Speed 1450r/min

Fan Speed
230 205 180 160 145 130 115 105 91 81
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
55 ※ ※ ※ 045 045 045 045 ※ ※ ※
75 ※ 045 045 045 045 055 055 055 055 055
90 ※ 045 045 045 055 055 055 055 055 060
110 ※ ※ 055 055 055 055 055 060 065 065
Motor
132 ※ ※ 055 055 055 060 060 065 070 070
(kW)
160 ※ ※ 060 060 060 065 065 065 075 075
200 ※ ※ 060 065 065 065 070 070 075 075
250 ※ ※ 065 065 070 075 075 075 ※ ※
280 ※ ※ ※ 070 070 075 075 ※ ※ ※

● Input Shaft Speed 970r/min

Fan Speed
155 135 120 110 97 87 78 69 61 54
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
55 ※ 045 045 045 045 055 055 055 055 055
75 ※ ※ 055 055 055 055 055 060 065 065
90 ※ ※ 055 055 055 060 060 065 070 070
110 060 060 060 060 060 065 065 070 075 075
Motor
132 060 060 060 065 065 065 070 075 075 ※
(kW)
160 065 065 065 065 070 070 075 075 ※ ※
200 065 065 070 075 075 075 075 ※ ※ ※
250 ※ ※ ※ ※ ※ ※ ※ ※ ※ ※
280 ※ ※ ※ ※ ※ ※ ※ ※ ※ ※
Attention
1) ※ symbol indicates a non-standard application. Inquire with Sumitomo for details.
2) For more specific details please use the selection method on page 6.
5

090624_SFC Series_E.indd 6 2009/12/15 17:35:02

 Selection Procedure

kW
● Selection Order
Item Selection Method Reference Page
Determine
Reduction Ratio ＝ Motor Speed ÷ Fan Speed ーーーー
Reduction Ratio
Determine
the Service SF = 2.0 ーーーー
Factor (SF)
Determine the
Motor Power ≦ Mechanical Rating (Service Factor 2.0) P.7 Rating Table
Reducer Size
P.8 Allowable Thrust
Actual Thrust Load ≦ Allowable Thrust Load on Slow Speed Shaft
Thrust Load Load on Slow
Conservatively calculated, Actual Thrust Load = Fan Thrust Load + Fan Weight Speed Shaft
Ambient
Standard ambient temperature operating range 0 ～ 40℃ ーーーー
Temperature

Input Shaft
Rotating Standard Input Shaft operating range 450 ～ 1800r/min ーーーー
Speed

Attention
1) Thrust load is the downward thrust load due to the weight and rotation of the cooling fan in the clockwise direction.
2) Allowable thrust load is based on a bearing life of 100,000 hours. Please inquire about cases above the 100,000 hour
limit.
3) Please inquire about operating ambient temperature that exceed the 0℃ to 40℃ range.
4) Please inquire about input shaft operating speeds lower than 450 r/min or higher than 1800 r/min.

● Selection Example

Required Specifications Selection

Use ： Cooling Tower 1. Determine Reduction Ratio

Motor Power ： 132kW × 1500r/min Motor Speed/Fan Speed ＝ 14

Cooling Fan Speed ： 107 r/min 2. Determine the Service Factor ･･･････････････････････ SF=2.0

Actual Thrust Load ： 14.7kN 3. Determine the Size

Rotation Direction ： Clockwise rotation Transfer Capacity (Motor Rating) ≦ Mechanical Rating ＠ SF2.0

Ambient Temperature ： 0 to 40℃ From Rating Table SFC065R2S-14 Ratio 14

Backstop ： Yes 132<160kW (Mechanical Rating @SF2.0) ････････････ OK

4. Check Thrust Load
Low Speed Shaft Allowable Thrust Load
14.7kN ＜ 28kN ･･･････････････････････････････････ OK
5. Check Ambient Temperature
Operating Ambient Temperature 0 ～ 40℃･････････････ OK
6. Check Input Shaft Operating Range
1500r/min Fixed Speed is within the 450-1800r/min
operating limits ･･････････････････････････････････ OK
7. With Backstop
Based on the selection criteria above, SFC065R2S-RRFB-14
is selected

090624_SFC Series_E.indd 7 2009/12/15 17:35:03

 Rating Table

Service Factor 2.0 kW

Unit : kW
Nominal Input Speed Output Size
Ratio r/min Speedr/min 045 055 060 065 070 075
Exact Ratio ※ ※ 6.188 6.426 6.188
1750 280 ※ ※ ※ ※ ※
6.3 1450 230 ※ ※ ※ ※ ※
1160 185 ※ ※ 191 227 260
970 155 ※ ※ 155 195 225
Exact Ratio 7.320 ※ 7.210 6.927 6.933
1750 245 115 ※ ※ ※ ※
7.1 1450 205 99 ※ ※ ※ ※
1160 165 77 ※ 189 216 260
970 135 64 ※ 154 186 225
Exact Ratio 8.338 7.955 7.875 8.118 8.082
1750 220 115 167 ※ ※ ※
8 1450 180 99 136 227 248 ※
1160 145 77 112 188 205 286
970 120 64 91 152 177 231
Exact Ratio 8.889 8.938 9.176 8.750 9.056 8.597
1750 195 105 167 223 ※ ※ ※
9 1450 160 91 136 180 235 287 324
1160 130 70 112 150 195 230 264
970 110 59 91 122 164 193 221
Exact Ratio 10.125 10.125 9.995 10.028 10.125 10.007
1750 175 95 171 211 256 ※ ※
10 1450 145 79 144 176 218 285 ※
1160 115 64 115 140 179 229 280
970 97 55 96 117 145 186 234
Exact Ratio 11.624 11.375 11.647 10.809 11.345 11.229
1750 155 78 142 171 235 284 ※
11.2 1450 130 65 119 143 204 230 304
1160 105 52 96 115 164 192 252
970 87 43 80 96 133 160 205
Exact Ratio 13.240 12.462 12.469 12.756 12.797 12.536
1750 140 75 138 161 202 257 340
12.5 1450 115 61 115 135 163 208 291
1160 93 49 94 105 135 167 234
970 78 41 77 90 113 139 201
Exact Ratio ※ 14.000 14.529 13.750 14.338 14.067
1750 125 ※ 116 138 193 233 301
14 1450 105 ※ 97 115 161 201 252
1160 83 ※ 78 95 125 162 202
970 69 ※ 66 77 105 131 164
Exact Ratio ※ 15.188 15.392 15.889 15.750 15.844
1750 110 ※ 113 131 151 188 257
16 1450 91 ※ 94 106 122 151 208
1160 73 ※ 75 85 97 122 167
970 61 ※ 61 71 82 101 139
Exact Ratio ※ 17.062 17.936 17.500 17.647 17.779
1750 97 ※ 96 112 133 185 232
18 1450 81 ※ 80 94 111 150 201
1160 64 ※ 65 75 89 120 156
970 54 ※ 55 63 77 101 131
Attention
1) When the desired input speed is not shown, use interpolation to determine the appropriate values. N
PN = P970 ×
2) When input speed (N) is below 970 r/min, use the following formula to determine the mechanical power rating (PN) 970
3) Please inquire with us when input shaft speed exceeds 1800r/min.
4) ※ Please inquire with us about these categories.
5) - No information available.
7

090624_SFC Series_E.indd 8 2009/12/15 17:35:04

 Allowable Thrust Load on Slow Speed Shaft

Unit：kN
kW
Output Shaft Size
Speed
(r/min) 045 055 060 065 070 075
≦ 300 16 25 22 28 29 50
≦ 150 18 27 27 28 31 50
≦ 100 21 29 30 34 39 50

090624_SFC Series_E.indd 9 2009/12/15 17:35:04

 Selection Procedure

Quick Selection Table HP

● Input Shaft Speed 1750r/min
Fan Speed
280 245 220 195 175 155 140 125 110 97
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
75 ※ ※ ※ ※ ※ 045 045 ※ ※ ※
100 ※ 045 045 045 045 045 045 055 055 055
125 ※ 045 045 045 045 055 055 055 055 055
150 ※ 045 045 055 055 055 055 055 055 060
Motor
175 ※ ※ 055 055 055 055 055 060 060 065
(HP)
200 ※ ※ 055 055 055 060 060 065 065 070
250 ※ ※ ※ 060 060 065 065 065 070 075
300 ※ ※ ※ ※ 065 065 070 070 075 075
350 ※ ※ ※ ※ ※ 070 075 075 ※ ※

● Input Shaft Speed 1160r/min

Fan Speed
185 165 145 130 115 105 93 83 73 64
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
75 ※ 045 045 045 045 055 055 055 055 055
100 ※ 045 045 055 055 055 055 055 055 060
125 ※ ※ 055 055 055 055 055 060 065 070
150 ※ ※ 055 055 055 060 065 065 070 070
Motor
175 060 060 060 060 060 065 065 070 075 075
(HP)
200 060 060 060 060 065 065 070 070 075 075
250 060 060 065 065 070 070 075 075 ※ ※
300 065 070 070 070 070 075 075 ※ ※ ※
350 ※ ※ 070 075 075 ※ ※ ※ ※ ※

● Input Shaft Speed 1450r/min

Fan Speed
230 205 180 160 145 130 115 105 91 81
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
75 ※ ※ ※ 045 045 045 045 ※ ※ ※
100 ※ 045 045 045 045 055 055 055 055 055
125 ※ 045 045 055 055 055 055 055 055 060
150 ※ ※ 055 055 055 055 055 060 065 070
Motor
175 ※ ※ 055 055 055 060 060 065 070 070
(HP)
200 ※ ※ 060 060 060 065 065 065 070 070
250 ※ ※ 060 065 065 065 070 070 075 075
300 ※ ※ 065 065 070 070 075 075 ※ ※
350 ※ ※ ※ 070 070 075 075 ※ ※ ※

● Input Shaft Speed 970r/min

Fan Speed
155 135 120 110 97 87 78 69 61 54
r/min
Reduction Ratio 6.3 7.1 8 9 10 11.2 12.5 14 16 18
75 ※ 045 045 045 055 055 055 055 055 060
100 ※ ※ 055 055 055 055 055 060 065 065
125 ※ ※ 060 060 055 060 065 065 070 070
150 060 060 060 060 060 065 065 070 075 075
Motor
175 060 060 060 065 065 065 070 070 075 075
(HP)
200 060 060 060 065 070 070 075 075 ※ ※
250 065 065 070 070 075 075 075 ※ ※ ※
300 070 070 070 ※ 075 ※ ※ ※ ※ ※
350 ※ ※ ※ ※ ※ ※ ※ ※ ※ ※
Attention
1) ※ symbol indicates a non-standard application. Inquire with Sumitomo for details.
2) For more specific details please use the selection method on page 10.
9

090624_SFC Series_E.indd 10 2009/12/15 17:35:05

 Selection Procedure

HP
● Selection Order
Item Selection Method Reference Page
Determine
Reduction Ratio ＝ Motor Speed ÷ Fan Speed ーーーー
Reduction Ratio
Determine
the Service SF = 2.0 ーーーー
Factor (SF)
Determine the
Motor Power ≦ Mechanical Rating (Service Factor 2.0) P.11 Rating Table
Reducer Size
P.12 Allowable Thrust
Actual Thrust Load ≦ Allowable Thrust Load on Slow Speed Shaft
Thrust Load Load on Slow
Conservatively calculated, Actual Thrust Load = Fan Thrust Load + Fan Weight Speed Shaft
Ambient
Standard ambient temperature operating range 0 ～ 40℃ ーーーー
Temperature

Input Shaft
Rotating Standard Input Shaft operating range 450 ～ 1800r/min ーーーー
Speed

Attention
1) Thrust load is the downward thrust load due to the weight and rotation of the cooling fan in the clockwise direction.
2) Allowable thrust load is based on a bearing life of 100,000 hours. Please inquire about cases above the 100,000 hour
limit.
3) Please inquire about operating ambient temperature that exceed the 0℃ to 40℃ range.
4) Please inquire about input shaft operating speeds lower than 450 r/min or higher than 1800 r/min.

● Selection Example

Required Specifications Selection

Use ： Cooling Tower 1. Determine Reduction Ratio

Motor Power ： 200HP × 1750r/min Motor Speed/Fan Speed ＝ 14

Cooling Fan Speed ： 107 r/min 2. Determine the Service Factor ･･･････････････････････ SF=2.0

Actual Thrust Load ： 14.7kN 3. Determine the Size

Rotation Direction ： Clockwise rotation Transfer Capacity (Motor Rating) ≦ Mechanical Rating ＠ SF2.0

Ambient Temperature ： 0 to 40℃ From Rating Table SFC065R2S-16 Ratio 16

Backstop ： Yes 200<202HP (Mechanical Rating @SF2.0) ･････････････ OK

4. Check Thrust Load
Low Speed Shaft Allowable Thrust Load
14.7kN ＜ 28kN ･･･････････････････････････････････ OK
5. Check Ambient Temperature
Operating Ambient Temperature 0 ～ 40℃･････････････ OK
6. Check Input Shaft Operating Range
1750r/min Fixed Speed is within the 450-1800r/min
operating limits ･･････････････････････････････････ OK
7. With Backstop
Based on the selection criteria above, SFC065R2S-RRFB-16
is selected

10

090624_SFC Series_E.indd 11 2009/12/15 17:35:06

 Rating Table

Service Factor 2.0 HP

Unit : HP
Nominal Input Speed Output Size
Ratio r/min Speedr/min 045 055 060 065 070 075
Exact Ratio ※ ※ 6.188 6.426 6.188
1750 280 ※ ※ ※ ※ ※
6.3 1450 230 ※ ※ ※ ※ ※
1160 185 ※ ※ 256 304 349
970 155 ※ ※ 208 261 302
Exact Ratio 7.320 ※ 7.210 6.927 6.933
1750 245 154 ※ ※ ※ ※
7.1 1450 205 133 ※ ※ ※ ※
1160 165 103 ※ 253 289 349
970 135 86 ※ 207 249 302
Exact Ratio 8.338 7.955 7.875 8.118 8.082
1750 220 154 224 ※ ※ ※
8 1450 180 133 182 304 332 ※
1160 145 103 150 252 274 354
970 120 86 122 204 237 310
Exact Ratio 8.889 8.938 9.176 8.750 9.056 8.597
1750 195 141 224 299 ※ ※ ※
9 1450 160 122 182 241 315 385 434
1160 130 94 150 201 261 308 354
970 110 79 122 164 220 259 296
Exact Ratio 10.125 10.125 9.995 10.028 10.125 10.007
1750 175 127 229 283 343 ※ ※
10 1450 145 106 193 236 292 382 ※
1160 115 86 154 188 240 307 375
970 97 74 129 157 194 249 314
Exact Ratio 11.624 11.375 11.647 10.809 11.345 11.229
1750 155 105 190 229 315 381 ※
11.2 1450 130 87 160 192 274 308 408
1160 105 70 129 154 220 257 338
970 87 58 107 129 178 215 275
Exact Ratio 13.240 12.462 12.469 12.756 12.797 12.536
1750 140 101 185 216 271 345 456
12.5 1450 115 82 154 181 219 279 390
1160 93 66 126 141 181 224 314
970 78 55 103 121 152 186 270
Exact Ratio ※ 14.000 14.529 13.750 14.338 14.067
1750 125 ※ 156 185 259 312 404
14 1450 105 ※ 130 154 216 270 338
1160 83 ※ 105 127 168 217 271
970 69 ※ 89 103 141 176 220
Exact Ratio ※ 15.188 15.392 15.889 15.750 15.844
1750 110 ※ 152 176 202 252 345
16 1450 91 ※ 126 142 164 202 279
1160 73 ※ 101 114 130 164 224
970 61 ※ 82 95 110 135 186
Exact Ratio ※ 17.062 17.936 17.500 17.647 17.779
1750 97 ※ 129 150 178 248 311
18 1450 81 ※ 107 126 149 201 270
1160 64 ※ 87 101 119 161 209
970 54 ※ 74 84 103 135 176
Attention
1) When the desired input speed is not shown, use interpolation to determine the appropriate values. N
2) When input speed (N) is below 970 r/min, use the following formula to determine the mechanical power rating (PN)
PN = P970 ×
970
3) Please inquire with us when input shaft speed exceeds 1800r/min.
4) ※ Please inquire with us about these categories.
5) No information available.
11

090624_SFC Series_E.indd 12 2009/12/15 17:35:07

 Allowable Thrust Load on Low Speed Shaft

HP
Unit：kN

Output Shaft Size

Speed
(r/min) 045 055 060 065 070 075
≦ 300 16 25 22 28 29 50
≦ 150 18 27 27 28 31 50
≦ 100 21 29 30 34 39 50

12

090624_SFC Series_E.indd 13 2009/12/15 17:35:08

 Application Data Sheet 

Enter the required specifications below when inquiring about SFC series reducers.
1.Load Conditions
No. Items Required specification
1 Motor Type (AC, Pole Change or Inverter)
2 Motor Power kW
Motor 3 Maximum Start-up Power kW
4 Absord Power kW
5 Input Shaft Speed (Min ･ Max) Min r/min Max r/min
6 Output Shaft Speed (Min ･ Max) Min r/min Max r/min
7 Thrust Load (Fan Thrust + Fan Mass) kN
Output
Output Shaft Rotation Direction
shaft 8
(View from the shaft end)
9 Maximum Torque kNm

2.Installation Environment
No. Items Required specification
Ambient Temperature Around the Gearbox Minimum Maximum
testing degC

Around the
Starting degC
10 Gearbox Operating degC
Temperature Customer comment:
Within 500mm distance from
gearbox housing surface

11 Temperature outside of stack degC

12 Temperature of cooling water degC
13 Country (area)
Condition of location
Environment 14
(coast, suburbs or others)
15 Corrosive Gas (ex. Hydrogen Sulfide etc.) Yes (Please describe: ), No

3.Cooling tower structure

No. Items Required specification
16 Method of fixing fan blade (Rigid or Flexible)
Disc diameter φA φA mm
Fan blade φB mm
17
(Detailed review is required, when sunshade
φB
effect can not be expected.)
Material (concrete, steel, wood or FRP) of ･ Structure:
18
cooling tower structure ･ Base plate:
Structure
Supporting structure underneath the gearbox
19
(Yes or No.)

4.Plant type cooling tower equipment

No. Items Required specification
Example.
･ Power generation
(Geothermal power, Natural gas or others)
Plant type 20 ･ Steel
･ Chemistry
･ Oil refinement
･ Others (Cement, Medicine or others)

Note,
Data must be specified for indicated items by the thick frame.

13

090624_SFC Series_E.indd 14 2009/12/15 17:35:09

 Dimensions 

B A K1

Oil Fill (DP1) K1 C FC

L2
L1
U

Air Vent (DP1)

Oil Gauge Cooling Fan
L

5
K2

OL
N2
H

Magnetic Plug Oil Drain/Fill (DP2) N1

G
M

X1

Z1
X2

Z2
Y1

Z
Y2
D
E1
D

W2
W1
S
V1
G

M M 4- J Low Speed Shaft High Speed Shaft

D D G
E1

Unit: mm
J Weight Oil Q'ty
Size A B C D E1 G H L P M OL
(Installation Bolt) (kg) (Liters)
045 725 260 645 200 470 35 38 28 (M24) 725 290 95 365 24 260
055 794 290 714 225 530 40 40 35 (M30) 795 320 105 435 34 290
060 865 305 750 240 560 40 45 35 (M30) 900 370 105 660 55 335
065 946 325 831 260 600 40 45 35 (M30) 990 395 105 830 75 360
070 965 350 850 275 650 50 52 42 (M36) 1010 415 135 960 90 375
075 1018 370 903 295 690 50 52 42 (M36) 1045 450 135 1250 110 410

Low Speed Shaft High Speed Shaft Pipe Thread

Size
V1 U1 L1 X1 Y1 Z1 W1/Depth S FC L2 X2 Y2 Z2 W2/Depth DP1 K1 K2 DP2 N1 N2
045 100m6 210 190 28 10 16 M24/50 45k6 80 80 14 5.5 9 M16/36 R1 190 393 R1 1/4 235 80
055 110m6 210 190 28 10 16 M24/50 50k6 80 80 14 5.5 9 M16/36 R1 210 445 R1 1/4 265 100
060 120m6 210 185 32 11 18 M24/50 60m6 115 105 18 7 11 M20/42 R1 1/4 260 505 R1 1/4 280 105
065 130m6 250 225 32 11 18 M24/50 65m6 115 105 18 7 11 M20/42 R1 1/4 280 555 R1 1/4 300 105
070 140m6 250 225 36 12 20 M30/60 65m6 115 105 18 7 11 M20/42 R1 1/4 290 575 R1 1/4 325 105
075 150m6 250 225 36 12 20 M30/60 65m6 115 105 18 7 11 M20/42 R1 1/4 310 610 R1 1/4 345 105

Attention
(1) Keys and keyways for both high speed and low speed shafts conform to ISO/R773-1969 close key. (JIS B 1301-1996 Parallel Key in
Fastening Type)
(2) The oil quantity shown is approximate. Fill to the appropriate level using the oil level gauge.
(3) Air breather and air breather pipe are assembled by the customer and installed on site. A pipe extending from the gearbox to outside
the fan stack should be prepared. Piping parts are not included.
(4) The installation bolts should be rated JIS Class 8.8 .
(5) To maintain coupling alignment, stop plates or knock pins should be installed to prevent gearbox twisting on its base due to fan opera-
tion.

14

090624_SFC Series_E.indd 15 2009/12/15 17:35:11

 The scope of our warranty for our products is limited to the range of our manufacture.
Warranty Warranty(Period and contents)
Warranty The warranty period for the Product shall be 18 months after the shipment of the Product from the
Period Seller's works or 12 months after the Product comes into operation, whichever comes first.

In the event that any problem or damage to the Product arises during the "Warranty Period" from
defects in the Product whenever the Product is properly installed and combined with the Buyer's
equipment or machines, maintained as specified in the maintenance manual, and properly operated
under the conditions described in the catalog or as otherwise agree upon in writing between the
Seller and the Buyer or its customers; the Seller will provide, at its sole discretion, appropriate repair
Warranty
or replacement of the Product without charge, except as stipulated in the "Exception for Warranty" as
Condition
described below.
However, if the Product is installed or integrated into the Buyer's equipment or machines, the Seller
shall not reimburse the cost of: removal or re-installation of the Product or other incidental costs related
thereto, any lost opportunity, any profit loss or other incidental or consequential losses or damages
incurred by the Buyer or its customers.

Not withstanding the above warranty, the warranty as set forth herein shall not apply to any problem or
damage to the Product that is caused by:
1. installation, connection, combination or integration of the Product in or to the other equipment or
machine that is rendered by any person or entity other than the Seller;
2. insufficient maintenance or improper operation by the Buyer or its customers, such that the Product
is not maintained in accordance with the maintenance manual provided or designated by the Seller;
3. improper use or operation of the Product by the Buyer or its customers that is not informed to the
Seller, including, without limitation, the Buyer's or its customers' operation of the Product not in
conformity with the specifications, or use of lubrication oil in the Product that is not recommended
Exception
by the Seller;
for
4. any problem or damage on any equipment or machine to which the Product is installed, connected
Warranty
or combined or on any specifications particular to the Buyer or its customers;
5. any changes, modifications, improvements or alterations to the Product or those functions that are
rendered on the Product by any person or entity other than the Seller;
6. any parts in the Product that are supplied or designated by the Buyer or its customers;
7. earthquake, fire, flood, sea-breeze, gas, thunder, acts of God or any other reasons beyond the
control of the Seller;
8. waste, exhaustion, normal wear and tear, or deterioration of the Product's parts, such as bearings,
oil-seals;
9. any other troubles, problems or damages to the Product that are not attributable to the Seller.

SAFETY PRECAUTIONS
● Strictly observe the safety rules for the installation place and the equipment to use.
(Industrial Safety and Health Law, Technical Standard for Electric Facilities, Extension Rules, Plant Explosion
Guidelines, Building Standards Law, etc.)
● Carefully read the maintenance manual before use. If the maintenance manual is not on hand, make a request
for one to the distributor at which you purchased the product or to our sales department. The maintenance
manual should be sent to the actual user.
● Select an appropriate product that matches the operating environment and usage.
● Install a protective equipment on the machine side when the machine is used for transportation of passengers or
for elevators, escalators, and dumbwaiters.
● When the machine is used for food processing equipment and others that are susceptible to oil, install an oil pan
or other damage preventive devices in case of oil leakage due to failure or termination of service life.

15

090624_SFC Series_E.indd 16 2009/12/15 17:35:11

090624_SFC Series_E.indd 17 2009/12/15 17:35:11
090624_SFC Series_E.indd 18 2009/12/15 17:35:11