Scribd
Upload
285 views4 pages

Service Directive - BEHRINGER X32 Fascia PDF

This document provides instructions for replacing the front fascia of an X32 audio console from May 2012 through July 2012. It instructs technicians to power down the unit, remove side panels, screws, and cables to separate the upper and lower sections of the console. Components like the LCD screen and fader assemblies are then removed from the front panel before swapping it and reassembling the console. The work must only be done by a qualified technician.

Uploaded by

Carlos Alberto de Andrade Freitas Junior
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
285 views4 pages

Service Directive - BEHRINGER X32 Fascia PDF

This document provides instructions for replacing the front fascia of an X32 audio console from May 2012 through July 2012. It instructs technicians to power down the unit, remove side panels, screws, and cables to separate the upper and lower sections of the console. Components like the LCD screen and fader assemblies are then removed from the front panel before swapping it and reassembling the console. The work must only be done by a qualified technician.

Uploaded by

Carlos Alberto de Andrade Freitas Junior
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

MODIFICATION INSTRUCTION X32

Project : X32 Fascia Replacement

Date Codes : May2012 thru July2012

Materials : Standard workshop equipment

Components Required : Replacement Fascia

!! This work must only be performed by a qualified technician !!

Changing The Front Fascia


When changing the front fascia, it is necessary to completely open the unit and remove
all the attached items. Refer to the X32 Exploded Drawing pages 92-93 at the bottom of
this document.

Two people are recommended for this.

Changing the Front Panel

Power down the unit and disconnect any other devices (loudspeakers, compressors,
etc).

Remove the side panels (ITEM 6) via the 5 screws per side.

CAREDepo_Instruction_X32_2012-8-30_Rev.0.odt
MODIFICATION INSTRUCTION X32

Remove the upper-back screws (ITEM 1) via 8 screws

Remove the upper screws from the side chassis panels (ITEM 2) via 5 screws per
side.

CAREFULLY peel off the rubber padding from the cell phone holder pad (ITEM 7).

Remove the cell phone holder by unscrewing the three screws (ITEM 3).

Unscrew the talkback XLR plate via 4 screws.

Remove 25 fader caps and the 3 knobs from the Monitor / Talkback section.

Remove the front bottom screws via 8 screws.

Remove the bottom screw by the middle foot bracket.

CAREFULLY pull and rotate the upper panel.

*NOTE: The lengths of the cabling will prevent the console from being
clam-shelled.

With the upper panel at a 90 degree angle, cut the Tie-wraps and unplug the
power cables that are preventing full rotation.

Unscrew the ferrite coil cover from LCD. Unseat the LCD ribbon cable via the
connector.

At this point, the upper and lower sections should be able to lay back to back.

Remove the front arm rest via 8 screws.

Remove the screws from each PCB attached to the upper panel, including the
fader PCBs, LCD, and fader assembly. To prevent leaving fingerprints on the
plastic screens, it is recommended that gloves be worn.

CAREDepo_Instruction_X32_2012-8-30_Rev.0.odt
MODIFICATION INSTRUCTION X32

Once the PCBs are removed from the front panel, remove the standoff brackets
(ITEM 15) via two nuts.

Swap the front panel and reassemble. Test all functions.

PAGE 92

CAREDepo_Instruction_X32_2012-8-30_Rev.0.odt
MODIFICATION INSTRUCTION X32

PAGE 93

Rev 0. 30Aug2012
Robert Feldman
CARE Depot US

CAREDepo_Instruction_X32_2012-8-30_Rev.0.odt

You might also like