Sr No DRAIN NO.xxx DRAIN NO.

for total South campus(beyond Nala)

Calculation of discharge & design of Storm water in respect of trapezoidal section rm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section h x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE – South Campus,TOTAL plot
Area in sqm 101500
in hectares 10.15
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 9.135

Q1 = CIA/360 in cumecs 2.4106

Unpaved area of the total area. In hectares 1.015

Q2 = CIA/360 in cumecs 0.1692

Total run off Q = Q1 + Q2 cumecs 2.5798

Actual discharge in cumecs 2.5798 91.01505

Trial 1. Assume some depth

Design of RCC drain
B diameter 1.2 3.936
B mtrs assumed (Trapz. Sect / Rect. Sect.) 1 3.280
B' mtrs assumed (Only for Trapz. Sect ) 1.3
Y mtrs B70 1.2 0.366
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 1.38
Area = 'a' sqm for rect. Sect = B*Y 1.2 12.912
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 1.1304 12.16129536
Trapz sect P= B + 2 x √2 x Y in m 4.39
OR Rect. Sect P= B + 2Y in m 3.4 11.152
OR Circular Section P =2*3.14*(B/2) 3.768 12.35904
R = a/P for trapz.sect 0.314
R = a/P for rect.sect 0.353
R = a/P for Circular.sect 0.300 0.984
Hydraulic radius m 0.300 0.9840
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 3.64 70.8 2.640588
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 3.43 75.3 2.854293
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 2.90 102.16 cft/s 89.1 2.561192

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 1.3
Width of drain mtrs ; rect.sect. 1
Dia of drain mtrs ; Circular sect. 1.2 OR, 0.9-2nos
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 1.2
Sr No DRAIN NO.Z1 DRAIN NO.South Campus_West spine road=Zone1
Calculation of discharge & design of Storm water in respect of trapezoidal section torm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section h)/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section dth x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru- South Campus

ZONE 1- UG sump, Kitchen, courts (West of spine road)
Area in sqm 16800
in hectares 1.68
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 1.512

Q1 = CIA/360 in cumecs 0.3990

Unpaved area of the total area. In hectares 0.168

Q2 = CIA/360 in cumecs 0.0280

Total run off Q = Q1 + Q2 cumecs 0.4270

Actual discharge in cumecs 0.4270 15.06456

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.7 2.296
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.55 1.804
B' mtrs assumed (Only for Trapz. Sect ) 0.7
Y mtrs (Trapz. Sect / Rect. Sect.) 0.55 0.168
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.34375
Area = 'a' sqm for rect. Sect = B*Y 0.3025 3.2549
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.38465 4.13821856
Trapz sect P= B + 2 x √2 x Y in m 2.11
OR Rect. Sect P= B + 2Y in m 1.65 5.412
OR Circular Section P =2*3.14*(B/2) 2.198 7.20944
R = a/P for trapz.sect 0.163
R = a/P for rect.sect 0.183
R = a/P for Circular.sect 0.175 0.574
Hydraulic radius m 0.175 0.5740
Author:
S = bed slope in m/m 0.0025 Slope 1:400 0.0033 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.59 72.8 1.707
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.56 76.5 1.844
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.69 24.27 cft/s 62.1 1.788

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.7
Width of drain mtrs ; rect.sect. 0.55
Dia of drain mtrs ; Circular sect. 0.7 OR, 0.5-2nos
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.55
Sr No DRAIN NO.Z2 DRAIN NO.South Campus_East spine road & shops 110,111,112=Zone2
Calculation of discharge & design of Storm water in respect of trapezoidal section rm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section h x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 2- East spine road & shops 110,111,112=Zone2
Area in sqm 32150
in hectares 3.215
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 2.8935

Q1 = CIA/360 in cumecs 0.7636

Unpaved area of the total area. In hectares 0.3215

Q2 = CIA/360 in cumecs 0.0536

Total run off Q = Q1 + Q2 cumecs 0.8171

Actual discharge in cumecs 0.8171 28.828905

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.8 2.624
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.6 1.968
B' mtrs assumed (Only for Trapz. Sect ) 0.75
Y mtrs (Trapz. Sect / Rect. Sect.) 0.8 0.244
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.54
Area = 'a' sqm for rect. Sect = B*Y 0.48 5.1648
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.5024 5.40502016
Trapz sect P= B + 2 x √2 x Y in m 2.86
OR Rect. Sect P= B + 2Y in m 2.2 7.216
OR Circular Section P =2*3.14*(B/2) 2.512 8.23936
R = a/P for trapz.sect 0.189
R = a/P for rect.sect 0.218
R = a/P for Circular.sect 0.200 0.656
Hydraulic radius m 0.200 0.6560
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 1.02 80.5 1.880
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.99 82.2 2.071
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.9820 34.65 cft/s 83.2 1.955

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.75
Width of drain mtrs ; rect.sect. 0.6
Dia of drain mtrs ; Circular sect. 0.8 OR, 0.6-2nos
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.8
Sr No DRAIN NO.Z3 DRAIN NO.ZONE 3- Central Ph-3 RnD bldgs=Zone3
Calculation of discharge & design of Storm water in respect of trapezoidal section rm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section h x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 3- Central Ph-3 RnD bldgs=Zone3
Area in sqm 15156
in hectares 1.5156
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 1.36404

Q1 = CIA/360 in cumecs 0.3600

Unpaved area of the total area. In hectares 0.15156

Q2 = CIA/360 in cumecs 0.0253

Total run off Q = Q1 + Q2 cumecs 0.3852

Actual discharge in cumecs 0.3852 13.5903852

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.6 1.968
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.5 1.640
B' mtrs assumed (Only for Trapz. Sect ) 0.65
Y mtrs (Trapz. Sect / Rect. Sect.) 0.5 0.152
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.2875
Area = 'a' sqm for rect. Sect = B*Y 0.25 2.69
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.2826 3.04032384
Trapz sect P= B + 2 x √2 x Y in m 1.91
OR Rect. Sect P= B + 2Y in m 1.5 4.92
OR Circular Section P =2*3.14*(B/2) 1.884 6.17952
R = a/P for trapz.sect 0.150
R = a/P for rect.sect 0.167
R = a/P for Circular.sect 0.150 0.492
Hydraulic radius m 0.150 0.4920
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.46 83.0 1.615
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.43 89.0 1.731
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.4560 16.09 cft/s 84.5 1.613

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.65
Width of drain mtrs ; rect.sect. 0.5
Dia of drain mtrs ; Circular sect. 0.6 OR, 0.45-2nos
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.5
Sr No DRAIN NO.Z4 DRAIN NO.- S campus-Z4
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 4 & 5- S campus 623, 6xx-DG-Ttrack-112a-110a
Area in sqm 30000
in hectares 3
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 2.7

Q1 = CIA/360 in cumecs 0.7125

Unpaved area of the total area. In hectares 0.3

Q2 = CIA/360 in cumecs 0.0500

Total run off Q = Q1 + Q2 cumecs 0.7625

Actual discharge in cumecs 0.7625 26.901

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.6 1.968
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.5 1.640
B' mtrs assumed (Only for Trapz. Sect ) 0.65
Y mtrs (Trapz. Sect / Rect. Sect.) 0.5 0.152
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.2875
Area = 'a' sqm for rect. Sect = B*Y 0.25 2.69
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.2826 3.04032384
Trapz sect P= B + 2 x √2 x Y in m 1.91
OR Rect. Sect P= B + 2Y in m 1.5 4.92
OR Circular Section P =2*3.14*(B/2) 1.884 6.17952
R = a/P for trapz.sect 0.150
R = a/P for rect.sect 0.167
R = a/P for Circular.sect 0.150 0.492
Hydraulic radius m 0.150 0.4920
S = bed slope in m/m 0.0028571429 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.50 153.6 1.726
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.46 164.8 1.850
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.4874 17.20 cft/s 156.4 1.725 78.21611

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.65
Width of drain mtrs ; rect.sect. 0.5
Dia of drain mtrs ; Circular sect. 0.6 0.6 -2nos
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.5
Sr No DRAIN NO.Z5 DRAIN NO.- S campus-66Kv s/s, testTrack-Z5
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 4- S campus623 area
Area in sqm 4000
in hectares 0.4
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 0.36

Q1 = CIA/360 in cumecs 0.0950

Unpaved area of the total area. In hectares 0.04

Q2 = CIA/360 in cumecs 0.0067

Total run off Q = Q1 + Q2 cumecs 0.1017

Actual discharge in cumecs 0.1017 3.5868

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.4 1.312
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.6 1.968
B' mtrs assumed (Only for Trapz. Sect ) 0.75
Y mtrs (Trapz. Sect / Rect. Sect.) 0.6 0.183
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.405
Area = 'a' sqm for rect. Sect = B*Y 0.36 3.8736
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.1256 1.35125504
Trapz sect P= B + 2 x √2 x Y in m 2.30
OR Rect. Sect P= B + 2Y in m 1.8 5.904
OR Circular Section P =2*3.14*(B/2) 1.256 4.11968
R = a/P for trapz.sect 0.176
R = a/P for rect.sect 0.200
R = a/P for Circular.sect 0.100 0.328
Hydraulic radius m 0.100 0.3280
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.73 14.0 1.797
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.70 14.4 1.955
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.1546 5.46 cft/s 65.7 1.231

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.75
Width of drain mtrs ; rect.sect. 0.6
Dia of drain mtrs ; Circular sect. 0.4
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.6
Sr No DRAIN NO.Z5 DRAIN NO.- S campus-66Kv s/s, testTrack-Z5
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 4- S campus623 area
Area in sqm 8000
in hectares 0.8
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 0.72

Q1 = CIA/360 in cumecs 0.1900

Unpaved area of the total area. In hectares 0.08

Q2 = CIA/360 in cumecs 0.0133

Total run off Q = Q1 + Q2 cumecs 0.2033

Actual discharge in cumecs 0.2033 7.1736

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.5 1.64
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.6 1.968
B' mtrs assumed (Only for Trapz. Sect ) 0.75
Y mtrs (Trapz. Sect / Rect. Sect.) 0.6 0.183
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.405
Area = 'a' sqm for rect. Sect = B*Y 0.36 3.8736
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.19625 2.111336
Trapz sect P= B + 2 x √2 x Y in m 2.30
OR Rect. Sect P= B + 2Y in m 1.8 5.904
OR Circular Section P =2*3.14*(B/2) 1.57 5.1496
R = a/P for trapz.sect 0.176
R = a/P for rect.sect 0.200
R = a/P for Circular.sect 0.125 0.41
Hydraulic radius m 0.125 0.4100
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.73 27.9 1.797
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.70 28.9 1.955
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.2804 9.89 cft/s 72.5 1.429

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.75
Width of drain mtrs ; rect.sect. 0.6
Dia of drain mtrs ; Circular sect. 0.5
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.6
Sr No DRAIN NO.Z5 DRAIN NO.- S campus-66Kv s/s, testTrack-Z5
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 5- S campus66Kv s/s, testTrac
Area in sqm 10000
in hectares 1
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 0.9

Q1 = CIA/360 in cumecs 0.2375

Unpaved area of the total area. In hectares 0.1

Q2 = CIA/360 in cumecs 0.0167

Total run off Q = Q1 + Q2 cumecs 0.2542

Actual discharge in cumecs 0.2542 8.967

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.5 1.64
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.6 1.968
B' mtrs assumed (Only for Trapz. Sect ) 0.75
Y mtrs (Trapz. Sect / Rect. Sect.) 0.6 0.183
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.405
Area = 'a' sqm for rect. Sect = B*Y 0.36 3.8736
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.19625 2.111336
Trapz sect P= B + 2 x √2 x Y in m 2.30
OR Rect. Sect P= B + 2Y in m 1.8 5.904
OR Circular Section P =2*3.14*(B/2) 1.57 5.1496
R = a/P for trapz.sect 0.176
R = a/P for rect.sect 0.200
R = a/P for Circular.sect 0.125 0.41
Hydraulic radius m 0.125 0.4100
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.73 34.9 1.797
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.70 36.1 1.955
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.2804 9.89 cft/s 90.6 1.429

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.75
Width of drain mtrs ; rect.sect. 0.6
Dia of drain mtrs ; Circular sect. 0.5
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.6
Sr No DRAIN NO.Z5 DRAIN NO.- S campus-66Kv s/s, testTrack-Z5
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 4- S campus -DG-623-6xx)
Area in sqm 24000
in hectares 2.4
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 2.16

Q1 = CIA/360 in cumecs 0.5700

Unpaved area of the total area. In hectares 0.24

Q2 = CIA/360 in cumecs 0.0400

Total run off Q = Q1 + Q2 cumecs 0.6100

Actual discharge in cumecs 0.6100 21.5208

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.7 2.296
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.6 1.968
B' mtrs assumed (Only for Trapz. Sect ) 0.75
Y mtrs (Trapz. Sect / Rect. Sect.) 0.6 0.183
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.405
Area = 'a' sqm for rect. Sect = B*Y 0.36 3.8736
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.38465 4.13821856
Trapz sect P= B + 2 x √2 x Y in m 2.30
OR Rect. Sect P= B + 2Y in m 1.8 5.904
OR Circular Section P =2*3.14*(B/2) 2.198 7.20944
R = a/P for trapz.sect 0.176
R = a/P for rect.sect 0.200
R = a/P for Circular.sect 0.175 0.574
Hydraulic radius m 0.175 0.5740
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.73 83.8 1.797
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.70 86.7 1.955
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.6878 24.27 cft/s 88.7 1.788

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.75
Width of drain mtrs ; rect.sect. 0.6
Dia of drain mtrs ; Circular sect. 0.7
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.6
Sr No DRAIN NO. 112+112a sheds DRAIN NO.- S campus-112+112a sheds (part Z2)
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 2- S campus-112 bldg (part Z2)
Area in sqm 1551
in hectares 0.1551
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 0.13959

Q1 = CIA/360 in cumecs 0.0368

Unpaved area of the total area. In hectares 0.01551

Q2 = CIA/360 in cumecs 0.0026

Total run off Q = Q1 + Q2 cumecs 0.0394

Actual discharge in cumecs 0.0394 1.3907817

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.3 0.984
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.4 1.312
B' mtrs assumed (Only for Trapz. Sect ) 0.45
Y mtrs (Trapz. Sect / Rect. Sect.) 0.3 0.091
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.1275
Area = 'a' sqm for rect. Sect = B*Y 0.12 1.2912
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.07065 0.76008096
Trapz sect P= B + 2 x √2 x Y in m 1.25
OR Rect. Sect P= B + 2Y in m 1 3.28
OR Circular Section P =2*3.14*(B/2) 0.942 3.08976
R = a/P for trapz.sect 0.102
R = a/P for rect.sect 0.120
R = a/P for Circular.sect 0.075 0.246
Hydraulic radius m 0.075 0.2460 40
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s 0.100
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.16 24.8 1.249
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.17 23.6 1.390
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.0718 2.53 cft/s 54.9 1.016

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.45
Width of drain mtrs ; rect.sect. 0.4
Dia of drain mtrs ; Circular sect. 0.3
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.3

IL at passage - before crossing at chamber 898.275

IL at passage - after crossing at chamber 898.265
Dist. From new CH to Ex. Open Drain 35
300
0.117
IL - at connection to existing open drain along West main road 898.148
Sr No DRAIN NO. 111+111a sheds DRAIN NO.- S campus-111+111a sheds (part Z2)
Calculation of discharge & design of Storm water in respect of trapezoidal section rm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section h x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 2- S campus-111+111a+110 bldgs (part Z2)
Area in sqm 4381 111= 46x15; 111a=53x15; 110=72x30; open area=(46+46)x8.
in hectares 0.4381
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 0.39429

Q1 = CIA/360 in cumecs 0.1040

Unpaved area of the total area. In hectares 0.04381

Q2 = CIA/360 in cumecs 0.0073

Total run off Q = Q1 + Q2 cumecs 0.1114

Actual discharge in cumecs 0.1114 3.9284427

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.45 1.476
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.4 1.312
B' mtrs assumed (Only for Trapz. Sect ) 0.5
Y mtrs (Trapz. Sect / Rect. Sect.) 0.4 0.122
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.18
Area = 'a' sqm for rect. Sect = B*Y 0.16 1.7216
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.1589625 1.71018216
Trapz sect P= B + 2 x √2 x Y in m 1.53
OR Rect. Sect P= B + 2Y in m 1.2 3.936
OR Circular Section P =2*3.14*(B/2) 1.413 4.63464
R = a/P for trapz.sect 0.118
R = a/P for rect.sect 0.133
R = a/P for Circular.sect 0.113 0.369
Hydraulic radius m 0.113 0.3690
S = bed slope in m/m 0.0025 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.25 45.1 1.371
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.24 46.7 1.492
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.2117 7.47 cft/s 52.6 1.332

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.5
Width of drain mtrs ; rect.sect. 0.4
Dia of drain mtrs ; Circular sect. 0.45
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.4

Open drain for 111 towards West Existing from 111a SE corner to 111SE corner
Start IL @ 111 SE corner 898.599 898.836 111a SE corner
Dist.m 46 53
Slope 1: 300 223.63
Drop 0.153 0.237
IL at passage - before chamber connection 111SW corner 898.446 898.599 111 SE corner

Open drain for 110 towards West

Start IL @110 NE corner 898.548
Dist.m 50 4
Slope 1: 300 300
Drop 0.167 0.013
IL at passage - before crossing at chamber 898.381
IL at passage - after crossing at chamber 898.366

Dist. From new CH to Ex. Open Drain 35

IL - at connection to existing open drain along West main road 898.250
Sr No DRAIN NO. All sheds DRAIN NO.- S campus-All sheds (part Z2) Diversion
Calculation of discharge & design of Storm water in respect of trapezoidal section orm water in respect of trapezoidal section
Rational formula for calculating runoff Q = (C I A) / 360 Q = (C I A) / 360 Wetted Perimeter of a Trapezoid
C– Co-efficient of run off Co-efficient of run off P = B + [(Z1*D)2 + D2]1/2 + [(Z2*D)2 + D2]1/2
I – Intensity of rainfall in mm/ hr. Intensity of rainfall in mm/ hr.
A – Drainage area in hectares. Drainage area in hectares. P = Wetted perimeter (ft.)
Run-off co-efficient for various types of surfaces B = Bottom width (ft.)
Open grounds, unpaved street 0.10 - 0.30 D = Depth of flow
Parks, lawns, gardens 0.10- 0.25 Z1 = Left side slope (z:1)
Macadam roads, pavements 0.25 - 0.70 Z2 = Right side slope (z:1)
Asphalt pavements 0.85 - 0.90
Water tight roof surface 0.90 - 0.95
Storm frequency
Intensity of precipitation.
Time of concentration
Manning’s formula for calculating the size of drain
Q= A x V =AxV
V = Velocity of flow in m/sec.
n = Co-efficient of friction, 0.013 0.013 0.013
R = Hydraulic mean depth in mts.
R=A/P
A=(Top width + bottom width)/2xdepth of flow for trapezoidal Section )/2xdepth of flow for trapezoidal Section
Bottom width x depth of flow for rectangular section th x depth of flow for rectangular section
P = Wetted perimeter in meters P = Wetted perimeter in meters
P=Bottom width + (2 x √2 x depth of flow) for trapezoidal section = B + 2 x √2 x Y
Where Y= depth of flow

Bottom width + 2 x depth of flow for rectangular section. = B + 2Y

S Hydraulic bed slope.

I DESIGN OF STORM WATER DRAIN. BAN600, Bangaluru

ZONE 2- S campus-all sheds (part Z2) For diversion
Area in sqm 13000 10800
in hectares 1.3
Intensity of rain fall in mm 100
c1= 0.95 Paved area 0.95
% of Paved area to the total area. 90%
c2= 0.60 Unpaved area-open ground 0.6
% of unPaved area to the total area. 10%

Paved area of the total area. In hectares 1.17

Q1 = CIA/360 in cumecs 0.3088

Unpaved area of the total area. In hectares 0.13

Q2 = CIA/360 in cumecs 0.0217

Total run off Q = Q1 + Q2 cumecs 0.3304

Actual discharge in cumecs 0.3304 11.6571

Trial 1. Assume some depth

Design of RCC drain
B diameter 0.6 1.968
B mtrs assumed (Trapz. Sect / Rect. Sect.) 0.6 1.968
B' mtrs assumed (Only for Trapz. Sect ) 0.7
Y mtrs (Trapz. Sect / Rect. Sect.) 0.45 0.137
Area = 'a' sqm for trapz.sect =((B+B')/2)*Y 0.2925
Area = 'a' sqm for rect. Sect = B*Y 0.27 2.9052
Area = 'a' sqm for circular . Sect = (3.142*B*B)/4 0.2826 3.04032384
Trapz sect P= B + 2 x √2 x Y in m 1.87
OR Rect. Sect P= B + 2Y in m 1.5 4.92
OR Circular Section P =2*3.14*(B/2) 1.884 6.17952
R = a/P for trapz.sect 0.156
R = a/P for rect.sect 0.180
R = a/P for Circular.sect 0.150 0.492
Hydraulic radius m 0.150 0.4920
S = bed slope in m/m 0.0022222222 0.0020 0.002 Usage% Vel.m/s
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Traps.sect. 0.46 72.3 1.563
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; rect.sect. 0.46 71.2 1.718
Calucalated discharge in cumecs =Q = a x 1.486/n x R2/3 x S1/2; Circular sect. 0.4299 15.17 cft/s 76.9 1.521 0.859748

Calculated discharge is higher than the actual discharge. Calculated discharge is higher than the
actual discharge.
Provided size of drain okay
Widths of drain mtrs (top width B') ; Traps.sect. 0.7
Width of drain mtrs ; rect.sect. 0.6
Dia of drain mtrs ; Circular sect. 0.6 OR 0.45-2nos
Depth of drain mtrs (Trapz. Sect / Rect. Sect.) 0.45