Scribd
Upload
105 views

G Clips

This document provides information on G-Clip grating fasteners made by Production Fastening Systems, L.L.C. It includes a chart that specifies the appropriate G-Clip model based on the thickness of the grating and structural member flange. It also lists the material specifications for galvanized carbon steel, 316 stainless steel, and aluminum models. Finally, it provides torque requirements for installation, stating that G-Clips should be tightened by hand to approximately 58 inch-pounds.

Uploaded by

Moanquile
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
105 views

G Clips

This document provides information on G-Clip grating fasteners made by Production Fastening Systems, L.L.C. It includes a chart that specifies the appropriate G-Clip model based on the thickness of the grating and structural member flange. It also lists the material specifications for galvanized carbon steel, 316 stainless steel, and aluminum models. Finally, it provides torque requirements for installation, stating that G-Clips should be tightened by hand to approximately 58 inch-pounds.

Uploaded by

Moanquile
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Production Fastening Systems, L.L.C.

New Orleans, LA

G-Clip Grating Fasteners

Structural Member Flange Thickness


Grating
1/4'' to 3/4'' to 1-1/4'' to 1-3/4'' to
Thickness
3/4'' 1-1/4'' 1-3/4'' 2-1/4''
1 inch GG-1A GG-2A GG-3A GG-4A
1-1/4 inch GG-1B GG-2B GG-3B GG-4B
1-1/2 inch GG-1C GG-2C GG-3C GG-4C
1-3/4 inch GG-1D GG-2D GG-3D GG-4D
2 inch GG-1E GG-2E GG-3E GG-4E

MATERIAL SPECIFICATIONS
Galvanized, carbon steel
 Fasteners body units are stamped, using 11 guage hot-
rolled, pickled and oiled, steel coils, conforming to ASTM A-366.
 Top units are identical, except that 16 guage coil is used,
and conforms to ASTM A-569.
 Top and body units are mechanically galvanized, after
stamping, with galvanized conforming to ASTM B-695, class
50 (2 mils thick).
 Threaded studs are grade 2 carbon steel, hex head cap screws, conforming to ASTM A-307, and
mechanically galvanized.
316 Stainless steel
 Fastener body units are stamped, using 13 guage hot rolled and annealed stainless steel coils,
conforming to ASTM A-240 and ASME SA-240.
 Top units are identical, except that 16 guage coil is used.
 Threaded studs are 316 stainless steel, hex head cap screws, conforming to ANSI B-18.2.1.
 Internal tooth lock washers are 410 stainless steel, conforming to ANSI B-27.1.
Aluminum
 Fastener body units are stamped, using 1/8″ thick, grade 5052 aluminum plate, conforming to ASTM
B-209 and Federal Spec. Q2A-250/8.
 Top units are identical, except that 13 guage plate is used.
 Threaded studs are 6061 T-6 aluminum, hex head cap screws, conforming to Federal Spec. QQA-
270.
Torque Requirements
 G-Clips should be tightened by hand, using a 7/16″ nut driver. When fully tightened
by the average installer, a torque value of approximately 58 inch/ pounds torque is realized,
according to tests. This is sufficient to allow the clips to resist typical vibration and stress loads to which
grating is often subjected.

WWW.PFSNO.COM Ph: 800-216-1827


[email protected] 504-427-1562
Fax: 504-891-6229

You might also like