Scribd
Upload
463 views4 pages

Retro Wrap

Ee project DESCRIPTION Redesigned 1952 retro wrap is lined to the edge and has patch pockets and collar. You WILL NEED 2yds (1.80m) of 45" wide fabric or 1-3 / 4yds of 60" (160cm) wide fabric.

Uploaded by

lcheg
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
463 views4 pages

Retro Wrap

Ee project DESCRIPTION Redesigned 1952 retro wrap is lined to the edge and has patch pockets and collar. You WILL NEED 2yds (1.80m) of 45" wide fabric or 1-3 / 4yds of 60" (160cm) wide fabric.

Uploaded by

lcheg
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

free

project

DESCRIPTION Redesigned 1952 retro wrap is lined to the edge and has patch pockets and collar.
FINISHED SIZE 18-3/4˝ X 101-1/2” (47.5cm X 258cm)

FABRIC SUGGESTIONS Lightweight Broadcloth, Lightweight Brocade, Lightweight Velvet and Taffeta.
LINING SUGGESTIONS Taffeta and Satin.

YOU WILL NEED • 2yds (1.80m) of 45˝ (114cm) wide fabric or 1-3/4yds of 60˝ (160cm) wide fabric
• 1-1/2yds (135cm) of lining
©2008 Butterick, The McCall Pattern Company 1
ENLARGING AND TRACING the pattern on page 4:
To enlarge the pattern, you can use one of the following methods:
•Trace the pattern pieces directly on the fabric – count each square as 1˝, draw the lines and cut out along the markings.
•Trace block pieces to Perfect Pattern Paper (available for purchasing on www.mccallpattern.com) or make your own grid
paper.
•Put the paper with pattern pieces on a scanner or photocopier and enlarge square to 1˝ (2.5cm) grid. You may have to print
it in sections and than tape the pages together.

NOTE: Seam allowances are 5/8" (1.3mm).

SEWING 1. 2.
INSTRUCTIONS:
2
Stitch FRONT AND BACK
(1) sections together at
center back.

Finish upper edge of


POCKET (2). 1
3.

Turn upper edge to


1
outside along foldline and
stitch ends. Trim, as
shown.

Turn upper edge to 4.


inside, turning in
remaining seam
allowance and diagonally
folding corners. Press.
5.

Pin pockets to front and


6.
back, matching symbols.
Edgestitch side and lower
edges. 3

With right sides together,


fold COLLAR (3) along 7.
foldline. Stitch ends. Trim.

Turn collar right side out.


Press. Baste raw edges
together.

©2008 Butterick, The McCall Pattern Company 2


On outside, pin collar to
8.
front and back between
large circles, matching
centers. Baste.
9.
Stitch front and back
LINING sections together
at center back, leaving an
opening for turning.

With right sides together,


pin lining to front and
back, having raw edges
even. Stitch along outer
edges. Trim.
10.

Turn lining to inside,


turning collar out; press.
Slipstitch back opening
edges together.

11.

©2008 Butterick, The McCall Pattern Company 3


CENTER BACK
ON FOLD
CENTER BACK
FOLDLINE

3
GRAINLINE

Cut 1 on fold
POCKET

Butterick

COLAR
Cut 2

GRAINLINE
Butterick

GRAINLINE
1
FRONT AND BACK
Fabric: Cut 2
Lining: Cut 2

Butterick

Produced entirely in the USA


©2008 Butterick, The McCall Pattern Company 4

You might also like